pcom-b632vg-user-manual---por

pcom-b632vg-user-manual---por
PCOM-B632VG
COM Express Type VI Non-ECC Module
User Manual
Version 1.0
Copyright © Portwell, Inc., 2013. All rights reserved.
All other brand names are registered trademarks of their respective owners
1
Preface
Preface
Revision History
Table 1.
Revision history
No.
Date
Author
Description
0.0
Nov.4.
2013
Portwell
Document started.
1.0
Feb.13.
2014
Portwell
Chapter 4 BIOS Setting Information updated.
1.1
Mar.26.
2014
Portwell
Chapter 2 HW configuration update.
Notational Conventions
This document lists and rates the required features of the product and provides some informative text to help the
reader understand the primary positioning and target of the platform and product.
Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview .......................................................................................................... 1
1.1 Introduction ...........................................................................................................1
1.2 Check List ...............................................................................................................1
1.3 Product Specification ............................................................................................2
1.4 Mechanical Drawing.............................................................................................3
1.5 System Architecture..............................................................................................4
Chapter 2 Hardware Configuration .............................................................................................. 5
2.1 Connector Allocation ............................................................................................5
Chapter 3 System Installation ..................................................................................................... 10
3.1
3.2
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.4
Intel® Vallyview CPU ............................................................................10
Main Memory ..........................................................................................10
Installing the Single Board Computer..................................................10
Chipset Component Driver ...........................................................11
Intel® Gen7 Graphic Controller ....................................................11
Intel I210LM Gigabit Ethernet Controller ...................................11
Intel HD Audio Controller ............................................................11
Intel Sideband Fabric Device .........................................................11
Intel Trusted Execution Engine .....................................................11
Clear CMOS Operation ..........................................................................12
Chapter 4 BIOS Setup Information ............................................................................................. 13
4.1 Entering Setup -- Launch System Setup ..........................................................13
4.2 Main ......................................................................................................................15
4.3 Advanced .............................................................................................................20
4.4 Others....................................................................................................................33
4.5 Security .................................................................................................................37
4.6 Boot .......................................................................................................................38
4.7 Exit.........................................................................................................................39
Chapter 5 Troubleshooting ......................................................................................................... 40
5.1
5.2
5.3
Hardware Quick Installation.................................................................40
BIOS Setting .............................................................................................41
FAQ ...........................................................................................................41
Preface
How to Use This Manual
The manual describes how to configure your PCOM-B632VG to meet various operating
requirements. It is divided into five chapters, with each chapter addressing a basic concept
and operation of this COM Express Module.
Chapter 1: System Overview. Presents what you have in the box and give you an overview of
the product specifications and basic system architecture for this model of single board
computer.
Chapter 2: Hardware Configuration. Show the definition and location of Jumpers and
Connectors that you can easily configure your system.
Chapter 3: System Installation. Describes how to properly mount the CPU, main memory to
get a safe installation and provides a programming guide of Watch Dog Timer function.
Chapter 4: BIOS Setup Information. Specifies the meaning of each setup parameters, how to
get advanced BIOS performance and update new BIOS. In addition, POST checkpoint list will
give users some guidelines of trouble-shooting.
Chapter 5: Trouble shooting.
The content of this manual and EC declaration document is subject to change without prior
notice. These changes will be incorporated in new editions of the document. Portwell may
make supplement or change in the products described in this document at any time.
Updates to this manual, technical clarification, and answers to frequently asked questions
will be shown on the following web site: http://www.portwell.com.tw
System Overview
Chapter 1
System Overview
1.1
Introduction
COM Express Type 6, holds by PICMG (PCI Industrial Computer Manufacturer Group) defines
new industrial computer platform in “Module board” and “Carrier board” architecture.
The “Module board” equipped processor or its socket, chipset, memory or memory socket
and single Ethernet controller on it. The On-The-Shelf Module board allows users to create
their own Carrier board easily and quickly since most critical parts are ready on Module
board. COM Express Module board offers expansion interfaces such as PCI Express, PCI,
SATA, LPC, HDMI, DP, DVI, and Audio etc. that could support variety functions depending on
Carrier board design.
The Carrier board was customized design to fit in different mechanical requirements. In
the meanwhile, its variety functions were also customized to meet the application.
Compare to the platform that designed from nothing, COM Express architecture platform
only needs to develop Carrier board. Users could keep their know-how which related to
their core competence in the Carrier board.
PCOM-B632 is Type VI COM Express Module board equipped Intel BayTrail BGA
processor ( 1.9GHz Quad Core、1.75GHz / 1.46GHz / 1.33GHz Dual Core and
1.46GHz single core processor on-board), one DDR3L SO-DIMM sockets, one
Gigabit Ethernet controller on it to provide expansion interfaces – PCI Express (x4 /
x1), eDP port (supports HDMI/DP/DVI), SATA and so on.
1.2
Check List
The PCOM-B632VG series package should cover the following basic items
 One PCOM-B632VG module board
If any of these items is damaged or missing, please contact your vendor and keep all packing
materials for future replacement and maintenance.
1
System Overview
1.3
Product Specification
#
1
2
Requirement
Form Factor
Processor
3
4
Chipset
Memory
5
6
BIOS
Ethernet
7
8
Graphic
Display
9
PCI Express
10
11
12
SATA
USB Port
Watchdog
Timer
LPC
13
14
15
16
Hardware
Monitoring
Connector
Audio
17
18
Board Size
Environment
Detailed Description
Type 6, Compact Form Factor COM Express
- Intel BayTrail-E3845, 1.91GHz 2MB Cache 4 Core (10W)
- Intel BayTrail-E3827, 1.75GHz 1MB Cache 2 Core (8W)
- Intel BayTrail-E3826, 1.46GHz 1MB Cache 2 Core (7W)
- Intel BayTrail-E3825, 1.33GHz 1MB Cache 2 Core (6W)
- Intel BayTrail-E3815, 1.46GHz 512KB Cache 1 Core (5W)
-SoC
-Supports up to 8GB DDR3L 1067/1333 MT/s SDRAM on one
204-pin SODIMM sockets.
- Phoenix UEFI
Intel® Ethernet Controller I210IT
(NC Sideband Interface, Jumbo frames , 1000Base-T)
Intel® Gen7 Graphics supports DX11.1, OpenGL 3.0 / ES2.0
eDP: Resolution up to 2560x1600
VGA: Resolution up to 2560x1600
DP: Resolution up to 2560x1600
PCI Express Gen2 (5.0GT/s)
x 4, x 2, x 1
2 x SATA 3.0Gb/s
4 x USB 1.0/2.0(HS/FS), 1 x USB3.0(SS).
Programmable via S/W from 1 sec to 255 min
LPC Interface (4-bit-wide bus operating at 4 times the clock speed,
33.3MHz)
-ITE 8528 ; CPU, Voltage , Temperature
COM Express Connector x2
Intel® High Definition Audio (2x channels delivering 192-KHz
32-bits, and 8x channels delivering 96-KHz 32-Bits)
95x95mm
-Operation Temperature:
-40° C ~ +85° C (-40° F~+185° F)
-Relative Humidity: 5~95%
2
System Overview
1.4
Mechanical Drawing
3
System Overview
1.5
System Architecture
4
Hardware Configuration
Chapter 2
Hardware Configuration
This chapter indicates connectors’ Pin Assignment.
SW1
J1
J5
J6
2.1
Connector Allocation
Connector Function List
Connector
Function
DDR3L channel connector.
J1
J5
COM Express connector raw C and D
COM Express connector raw A and B
J6
SW1
1-4
2-3
Function
Remark
Default Off
Default Off
ATX_DETECT
BIOS_RECOVERY
Pin Assignment of Connectors
J6
Row A
Pin No
Signal
Description
Remark
J5
Row B
Pin No
Signal
Description
Row C
Pin No
Signal
Description
Row D
Pin No
Signal
Description
A1
GND (FIXED)
B1
GND (FIXED)
C1
GND (FIXED)
D1
GND (FIXED)
A2
GBE0_MDI3-
B2
GBE0_ACT#
C2
GND
D2
GND
A3
GBE0_MDI3+
B3
LPC_FRAME#
C3
USB0_SSRX-
D3
USB0_SSTX-
5
Hardware Configuration
A4
A5
GBE0_LINK100
B4
#
GBE0_LINK100
B5
0#
LPC_AD0
C4
USB0_SSRX+
D4
USB0_SSTX+
LPC_AD1
C5
GND
D5
GND
A6
GBE0_MDI2-
B6
LPC_AD2
C6
USB1_SSRX-
D6
USB1_SSTX-
A7
GBE0_MDI2+
B7
LPC_AD3
C7
USB1_SSRX+
D7
USB1_SSTX+
A8
GBE0_LINK#
B8
LPC_DRQ0#
C8
GND
D8
GND
A9
GBE0_MDI1-
B9
LPC_DRQ1#
C9
USB2_SSRX-
D9
USB2_SSTX-
A10
GBE0_MDI1+
B10
LPC_PCLK
C10
USB2_SSRX+
D10
USB2_SSTX+
A11
GND (FIXED)
B11
GND (FIXED)
C11
GND (FIXED)
D11
GND (FIXED)
A12
GBE0_MDI0-
B12
PWRBTN#
C12
USB3_SSRX-
D12
USB3_SSTX-
A13
GBE0_MDI0+
B13
SMB_CLK
C13
USB3_SSRX+
D13
USB3_SSTX+
A14
GBE0_CTREF
B14
SMB_DAT
C14
GND
D14
GND
A15
SUS_S3#
B15
SMB_ALERT#
C15
DP1_LANE6
D15
A16
SATA0_TX+
B16
SATA1_TX+
C16
DP1_LANE6#
D16
A17
SATA0_TX-
B17
SATA1_TX-
C17
NC
D17
NC
A18
SUS_S4#
B18
SUS_STAT#
C18
NC
D18
NC
A19
SATA0_RX+
B19
SATA1_RX+
C19
PCIE_RX6+
D19
PCIE_TX6+
A20
SATA0_RX-
B20
SATA1_RX-
C20
PCIE_RX6-
D20
PCIE_TX6-
A21
GND (FIXED)
B21
GND (FIXED)
C21
GND (FIXED)
D21
GND (FIXED)
A22
SATA2_TX+
B22
SATA3_TX+
C22
NC
D22
NC
A23
SATA2_TX-
B23
SATA3_TX-
C23
NC
D23
NC
A24
SUS_S5#
B24
PWROK
C24
DP1_HDP
D24
NC
A25
SATA2_RX+
B25
SATA3_RX+
C25
DP1_LANE4
D25
NC
A26
SATA2_RX-
B26
SATA3_RX-
C26
DP1_LANE4#
D26
DP1_LANE0
A27
BATLOW#
B27
WDT
C27
NC
D27
DP1_LANE0#
A28
ATA_ACT#
B28
HDA_SDIN2
C28
NC
D28
NC
A29
HDA_SYNC
B29
HDA_SDIN1
C29
DP1_LANE5
D29
DP1_LANE1
A30
HDA_RST#
B30
HDA_SDIN0
C30
DP1_LANE5#
D30
DP1_LANE1#
A31
GND (FIXED)
B31
GND (FIXED)
C31
GND (FIXED)
D31
GND (FIXED)
A32
HDA_BITCLK
B32
SPKR
C32
A33
HDA_SDOUT
B33
I2C_CLK
C33
A34
BIOS_DIS0#
B34
I2C_DAT
C34
DP2_AUX_SEL D34
DP1_AUX_SEL
A35
THRMTRIP#
B35
THRM#
C35
NC
NC
A36
USB6-
B36
USB7-
C36
A37
USB6+
B37
USB7+
C37
DP2_CTRLCLK_
D32
AUX
DP2_CTRLDATA
D33
_AUX#
D35
DP3_CTRLCLK_
D36
AUX
DP3_CTRLDATA
D37
_AUX#
6
DP1_CTRLCLK_
AUX
DP1_CTRLDATA
_AUX#
DP1_LANE2
DP1_LANE2#
DP1_LANE3
DP1_LANE3#
Hardware Configuration
A38
USB_6_7_OC# B38
USB_4_5_OC# C38
DP3_AUX_SEL D38
NC
A39
USB4-
B39
USB5-
C39
DP3_LANE0
D39
DP2_LANE0
A40
USB4+
B40
USB5+
C40
DP3_LANE0#
D40
DP2_LANE0#
A41
GND (FIXED)
B41
GND (FIXED)
C41
GND (FIXED)
D41
GND (FIXED)
A42
USB2-
B42
USB3-
C42
DP3_LANE1
D42
DP2_LANE1
A43
USB2+
B43
USB3+
C43
DP3_LANE1#
D43
DP2_LANE1#
A44
USB_2_3_OC# B44
USB_0_1_OC# C44
DP3_HPD
D44
DP2_HPD
A45
USB0-
B45
USB1-
C45
NC
D45
NC
A46
USB0+
B46
USB1+
C46
DP3_LANE2
D46
DP2_LANE2
A47
VCC_RTC
B47
EXCD1_PERST# C47
DP3_LANE2#
D47
DP2_LANE2#
A48
EXCD0_PERST# B48
EXCD1_CPPE# C48
NC
D48
NC
A49
EXCD0_CPPE# B49
SYS_RST#
C49
DP3_LANE3
D49
DP2_LANE3
A50
LPC_SERIRQ
B50
CB_RESET#
C50
DP3_LANE3#
D50
DP2_LANE3#
A51
GND (FIXED)
B51
GND (FIXED)
C51
GND (FIXED)
D51
GND (FIXED)
A52
PCIE_TX5+
B52
PCIE_RX5+
C52
PEG_RX0+
D52
PEG_TX0+
A53
PCIE_TX5-
B53
PCIE_RX5-
C53
PEG_RX0-
D53
PEG_TX0-
A54
GPI0
B54
GPO1
C54
NC
D54
PEG_LANE_RV
#
A55
PCIE_TX4+
B55
PCIE_RX4+
C55
PEG_RX1+
D55
PEG_TX1+
A56
PCIE_TX4-
B56
PCIE_RX4-
C56
PEG_RX1-
D56
PEG_TX1-
A57
GND
B57
GPO2
C57
NC
D57
NC
A58
PCIE_TX3+
B58
PCIE_RX3+
C58
PEG_RX2+
D58
PEG_TX2+
A59
PCIE_TX3-
B59
PCIE_RX3-
C59
PEG_RX2-
D59
PEG_TX2-
A60
GND (FIXED)
B60
GND (FIXED)
C60
GND (FIXED)
D60
GND (FIXED)
A61
PCIE_TX2+
B61
PCIE_RX2+
C61
PEG_RX3+
D61
PEG_TX3+
A62
PCIE_TX2-
B62
PCIE_RX2-
C62
PEG_RX3-
D62
PEG_TX3-
A63
GPI1
B63
GPO3
C63
NC
D63
NC
A64
PCIE_TX1+
B64
PCIE_RX1+
C64
NC
D64
NC
A65
PCIE_TX1-
B65
PCIE_RX1-
C65
PEG_RX4+
D65
PEG_TX4+
A66
GND
B66
WAKE0#
C66
PEG_RX4-
D66
PEG_TX4-
A67
GPI2
B67
WAKE1#
C67
NC
D67
GND
A68
PCIE_TX0+
B68
PCIE_RX0+
C68
PEG_RX5+
D68
PEG_TX5+
A69
PCIE_TX0-
B69
PCIE_RX0-
C69
PEG_RX5-
D69
PEG_TX5-
A70
GND (FIXED)
B70
GND (FIXED)
C70
GND (FIXED)
D70
GND (FIXED)
A71
LVDS_A0+
B71
LVDS_B0+
C71
PEG_RX6+
D71
PEG_TX6+
A72
LVDS_A0-
B72
LVDS_B0-
C72
PEG_RX6-
D72
PEG_TX6-
A73
LVDS_A1+
B73
LVDS_B1+
C73
GND
D73
GND
7
Hardware Configuration
A74
LVDS_A1-
B74
LVDS_B1-
C74
PEG_RX7+
D74
PEG_TX7+
A75
LVDS_A2+
B75
LVDS_B2+
C75
PEG_RX7-
D75
PEG_TX7-
A76
LVDS_A2-
B76
LVDS_B2-
C76
GND
D76
GND
A77
LVDS_VDDEN
B77
LVDS_B3+
C77
NC
D77
NC
A78
LVDS_A3+
B78
LVDS_B3-
C78
PEG_RX8+
D78
PEG_TX8+
A79
LVDS_A3-
B79
LVDS_BKLT_EN C79
PEG_RX8-
D79
PEG_TX8-
A80
GND (FIXED)
B80
GND (FIXED)
C80
GND (FIXED)
D80
GND (FIXED)
A81
LVDS_CLKA+
B81
LVDS_CLKB+
C81
PEG_RX9+
D81
PEG_TX9+
A82
LVDS_CLKA-
B82
LVDS_CLKB-
C82
PEG_RX9-
D82
PEG_TX9-
A83
LVDS_I2CCK
B83
LVDS_BKLT_CT
C83
RL
NC
D83
NC
A84
LVDS_I2CDAT
B84
VCC_5V_SBY
C84
GND
D84
GND
A85
GPI3
B85
VCC_5V_SBY
C85
PEG_RX10+
D85
PEG_TX10+
A86
NC
B86
VCC_5V_SBY
C86
PEG_RX10-
D86
PEG_TX10-
A87
NC
B87
VCC_5V_SBY
C87
GND
D87
GND
A88
PCIE0_CK_REF
B88
+
BIOS_DIS1#
C88
PEG_RX11+
D88
PEG_TX11+
A89
PCIE0_CK_REF- B89
VGA_RED
C89
PEG_RX11-
D89
PEG_TX11-
A90
GND (FIXED)
B90
GND (FIXED)
C90
GND (FIXED)
D90
GND (FIXED)
A91
SPI_POWER
B91
VGA_GRN
C91
PEG_RX12+
D91
PEG_TX12+
A92
SPI_MISO
B92
VGA_BLU
C92
PEG_RX12-
D92
PEG_TX12-
A93
GPO0
B93
VGA_HSYNC
C93
GND
D93
GND
A94
SPI_CLK
B94
VGA_VSYNC
C94
PEG_RX13+
D94
PEG_TX13+
A95
SPI_MOSI
B95
VGA_DDC_CLK C95
PEG_RX13-
D95
PEG_TX13-
A96
NC
B96
VGA_DDC_DAT C96
GND
D96
GND
A97
TYPE10#
B97
SPI_CS#
C97
NC
D97
NC
A98
SER0_TX
B98
NC
C98
PEG_RX14+
D98
PEG_TX14+
A99
SER0_RX
B99
NC
C99
PEG_RX14-
D99
PEG_TX14-
A100
GND (FIXED)
B100
GND (FIXED)
C100
GND (FIXED)
D100
GND (FIXED)
A101
SER1_TX
B101
FAN_PWNOUT C101
PEG_RX15+
D101
PEG_TX15+
A102
SER1_RX
B102
FAN_TACHIN
C102
PEG_RX15-
D102
PEG_TX15-
A103
LID#
B103
SLEEP#
C103
GND
D103
GND
A104
VCC_12V
B104
VCC_12V
C104
VCC_12V
D104
VCC_12V
A105
VCC_12V
B105
VCC_12V
C105
VCC_12V
D105
VCC_12V
A106
VCC_12V
B106
VCC_12V
C106
VCC_12V
D106
VCC_12V
A107
VCC_12V
B107
VCC_12V
C107
VCC_12V
D107
VCC_12V
A108
VCC_12V
B108
VCC_12V
C108
VCC_12V
D108
VCC_12V
A109
VCC_12V
B109
VCC_12V
C109
VCC_12V
D109
VCC_12V
8
Hardware Configuration
A110
GND (FIXED)
B110
GND (FIXED)
C110
GND (FIXED)
9
D110
GND (FIXED)
System Installation
Chapter 3
System Installation
This chapter provides you with instructions to set up your system. The additional
information is enclosed to help you set up onboard PCI device and handle Watch Dog Timer
(WDT) and operation of GPIO in software programming.
3.1
Intel® Valleyview CPU
Intel® E3845 (4 core, 10W, 1.91GHz, 1333MT)
Intel® E3827 (2 core, 8W, 1.75GHz, 1333MT)
Intel® E3826 (2 core, 7W, 1.46GHz, 1067MT)
Intel® E3825 (2 core, 6W, 1.33GHz, 1067MT)
Intel® E3815 (1 core, 5W, 1.46GHz, 1067MT)
3.2
Main Memory
PCOM-B632 provides 1 x 204-pin SO-DIMM sockets which supports 1333 MT/s
DDR3L-SDRAM (1.35V) as main memory, Non-ECC (Error Checking and Correcting),. The
maximum memory can be up to 8GB. Memory clock and related settings can be detected by
BIOS via SPD interface.
Watch out the contact and lock integrity of memory module with socket, it will impact on
the system reliability. Follow normal procedures to install memory module into memory
socket. Before locking, make sure that all modules have been fully inserted into the card
slots.
3.3
Installing the Single Board Computer
To install your PCOM-B632 into standard chassis or proprietary environment, please perform
the following:
Step 1: Check all jumpers setting on proper position
Step 2: Install and configure CPU and memory module on right position
Step 3: Place PCOM-B632 into the dedicated position in the system
Step 4: Attach cables to existing peripheral devices and secure it
WARNING
Please ensure that SBC is properly inserted and fixed by mechanism.
Note:
Please refer to section 3.3.1 to 3.3.6 to install INF/VGA/LAN/Audio/Sideband Fabric
10
System Installation
Device/Trusted Execution Engine drivers.
3.3.1
Chipset Component Driver
PCOM-B632 uses state-of-art Intel® BayTrail-I chipset. It’s a new chipset that some old
operating systems might not be able to recognize. To overcome this compatibility issue, for
Windows Operating Systems such as Windows 8, please install its INF before any of other
Drivers are installed. You can find very easily this chipset component driver in PCOM-B632
CD-title
3.3.2
Intel® Gen7 Graphic Controller
PCOM-B632 has integrated Intel® Gen7 Graphic which supports DX11, OpenGL3.2. It is the
most advanced design to gain an outstanding graphic performance. PCOM-B632 supports
VGA, eDP (Optional), DP (1.1a) (Optional), HDMI (Optional) and dual display (Optional). This
combination makes PCOM-B632 an excellent piece of multimedia hardware.
Drivers Support
Please find the Graphic driver in the PCOM-B632 CD-title. The driver supports Windows 8.
3.3.3
Intel I210LM Gigabit Ethernet Controller
Drivers Support
Please find Intel I210LM LAN driver in /Ethernet directory of PCOM-B632 CD-title. The driver
supports Windows 8.
3.3.4
Intel HD Audio Controller
Please find Intel® High Definition Audio driver form PCOM-B632 CD-title. The driver supports
Windows 8.
3.3.5
Intel Sideband Fabric Device
Please find Intel® Sideband Fabric Device driver form PCOM-B632 CD-title. The driver
supports Windows 8.
3.3.6
Intel Trusted Execution Engine
Please find Intel® Trusted Execution Engine driver form PCOM-B632 CD-title. The driver
supports Windows 8.
11
System Installation
3.4
Clear CMOS Operation
The following table indicates how to enable/disable Clear CMOS Function hardware circuit
by putting jumper of the PCOM-C600 carrier board.
JP20:CMOS Setting
Jumper Setting Describe
*1-2
Default
2-3
Clean CMOS
12
BIOS Setup Information
Chapter 4
BIOS Setup Information
PCOM-B632 is equipped with the Phoenix BIOS stored in Flash ROM. These BIOS has a
built-in Setup program that allows users to modify the basic system configuration easily. This
type of information is stored in CMOS RAM so that it is retained during power-off periods.
When system is turned on, PCOM-B632 communicates with peripheral devices and checks
its hardware resources against the configuration information stored in the CMOS memory. If
any error is detected, or the CMOS parameters need to be initially defined, the diagnostic
program will prompt the user to enter the SETUP program. Some errors are significant
enough to abort the start up.
4.1
Entering Setup -- Launch System Setup
Power on the computer and the system will start POST (Power On Self Test) process. When
the message below appears on the screen, press <F2> key will enter BIOS setup screen.
Press <F2> to enter SETUP
If the message disappears before responding and still wish to enter Setup, please restart the
system by turning it OFF and On or pressing the RESET button. It can be also restarted by
pressing <Ctrl>, <Alt>, and <Delete> keys on keyboard simultaneously.
Press <F1> to Run General Help or Resume
The BIOS setup program provides a General Help screen. The menu can be easily called up
from any menu by pressing <F1>. The Help screen lists all the possible keys to use and the
selections for the highlighted item. Press <Esc> to exit the Help screen.
13
BIOS Setup Information
14
BIOS Setup Information
4.2
Main
Use this menu for basic system configurations, such as time, date etc.
System Date
View or set system date
The date format is <Day>, <Month> <Date> <Year>. Use [+] or [-] to configure system
Date.
System Time
View or set system time
The time format is <Hour> <Minute> <Second>. Use [+] or [-] to configure system Time.
15
BIOS Setup Information
System Information
Display System Information, Show only.
16
BIOS Setup Information
Boot Features
Select Boot features
NumLock:
Selects Power-on state for NumLock
Choices: On, Off.
Timeout
Number of seconds that P.O.S.T will wait for the user input before booting
Choices: 0-99 seconds.
CSM Support
Compatibility Support Module that provides backward compatibility services for legacy BIOS
services, like int10/int13, dependent OS.
Choices: No, Yes.
Quick Boot
Enable/Disable quick boot
Choices: Disable, Enable.
Diagnostic Splash Screen
If you select ‘Enabled’ the diagnostic splash screen always displays during boot. If you select
‘Disabled’ the diagnostic splash screen does not displays unless you press HOTKEY during
boot
Choices: Disable, Enable.
17
BIOS Setup Information
Diagnostic Summary Screen
Display the Diagnostic summary screen during boot
Choices: Disable, Enable.
BIOS Level USB
Enable/Disable all BIOS support for USB in order to reduce boot time. Note that this will
prevent using a USB keyboard in setup or a USB biometric scanner such as a finger print
reader to control access to setup, but does not prevent the operating system from
supporting such hardware
Choices: Disable, Enable.
Console Redirection
Enable/Disable Universal Console Redirection
Choices: Disable, Enable.
Terminal Type
Set terminal type of UCR.
Choices: ANSI, VT100, VT100+, UTF8.
Baud rate
Set baud rate of UCR.
Choices: 9600, 19200, 38400, 57600, 115200.
Flow Control
Set flow control method for UCR.
[None] – No flow control.
[RTS/CTS] – Hardware flow control.
[XON/XOFF] – Software flow control.
Choices: None, RTS/CTS, XON/XOFF.
Continue C.R. after POST
Enables Console Redirection after OS has loaded.
Choices: Disable, Enable.
Allow Hotkey in S4 Resume
Enable hotkey detection when system resuming from Hibernate state
Choices: Disable, Enable.
UEFI Boot
Enable the UEFI boot
Choices: Disable, Enable.
Legacy Boot
Enable the Legacy boot
Choices: Disable, Enable.
Boot in Legacy Video Mode
18
BIOS Setup Information
Enable to force the display adapter to switch the video mode to Text Mode 3 at the end of
BIOS POST for non-UEFI boot mode (Legacy Boot). Some legacy software, such as DUET,
requires that the BIOS explicitly enter text video mode prior to boot.
Choices: Disable, Enable.
Load OPROM
Load all OPROMs or on demand according to the boot device.
Choices: All, On Demand.
19
BIOS Setup Information
4.3
Advanced
Setup Warning:
Setting items on this screen to incorrect values may cause system to malfunction!
20
BIOS Setup Information
CPU Configuration
Active Processor Cores
Number of cores to enable in each processor package
Choices: All, 1.
Execute Disabled Bit
Execute Disabled Bit prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS
Choices: Disable, Enable.
Limit CPUID Maximum
Disabled for Windows XP
Choices: Disable, Enable.
Bi-directional PROCHOT#
When a processor thermal sensor trips (either core), the PROCHOT# will be driven
If bi-direction is enabled, external agents can drive PROCHOT# to throttle the processor
Choices: Disable, Enable.
VTX-2
To enable or disable the VTX-2 Mode support
Choices: Disable, Enable.
TM1
21
BIOS Setup Information
Enable/Disable TM1
Choices: Disable, Enable.
DTS
Enabled/Disable Digital Thermal Sensor
Choices: Disable, Enable.
CPU Power Management
System Power Options
Intel® SpeedStep™
Enable processor performance states (P-States)
Choices: Disabled, Enabled.
Boot performance mode
Select the performance state that the BIOS will set before OS handoff
Choices: Max Performance, Max Battery.
Intel® Turbo Boost Technology
Enable to automatically allow processor cores to run faster than the base operating
frequency if it’s operating below power, current, and temperature specification limits.
Choices: Disable, Enable.
22
BIOS Setup Information
C-States
Enable/Disable C States
Choices: Disable, Enable.
Enhanced C-States
Enable/Disable C1E, C2E and C4E. When enabled, CPU will switch to minimum speed when
all cores enter C-State
Choices: Disable, Enable.
Max C State
This option controls the Max C State that the processor will support
Choices: C7, C6, C4, C1.
Uncore Configuration
(Some Optional items are shown only)
GOP Driver (Optional)
Enable GOP Driver will unload VBIOS; Disable it will load VBIOS
Choices: Enable, Disable.
Integrated Graphic Device (Optional)
Enable: Enable Integrated Graphics Device (IGD) when selected as the Primary Video Adapter.
Disable: Always disable IGD
Choices: Disable, Enable.
23
BIOS Setup Information
Primary Display (Optional)
Select which of IGD/PCI Graphics device should be Primary Display.
Choices: Auto, IGFX, IGD, PCIe.
RC6 (Rander Standby) (Optional)
Check to enable render standby support
Choices: Enable, Disable.
PAVC
Enable/Disable Protected Audio Video control
Choices: Disable, LITE Mode, SERPENT Mode.
GTT Size (Optional)
Select the GTT Size
Choices: 1MB, 2MB.
Aperture Size (Optional)
Select the Aperture Size
Choices: 128MB, 256MB, 512MB.
DVMT Pre-Allocated (Optional)
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory sized used by the Internal Graphic
Device
Choices: 32M, 64M, 96M, 128M, 160M, 192M, 224M, 256M, 288M, 320M, 352M,
384M,416M, 448M, 480M, 512M.
Spread Spectrum clock (Optional)
Enable clock chip Spread Spectrum feature
Choices: Disable, Enable.
Force Lid States (Optional)
For test: Force to set lid status as on or off
Choices: OFF, ON.
BIA
>> Auto: GMCH Use VBIOS Default;
>>Level n: Enabled with Selected Aggressiveness Level.
Choices: Auto, Disabled, Level 1, Level 2, Level 3, Level 4, Level 5.
LCD Panel Type
Choices: Auto, 640x480, 800x600, 1024x768, 1280x1024, 1366x768, 1680x1050, 1600x1200,
1280x800.
IGD Boot Type (Optional)
Select preference for Integrated Graphics Device (IGD) display interface used when system
boots
Choices: Auto, VGA Port, HDMI Port B, DP Port B, DP Port C, eDP, DSI PORT A, DSI PORT C.
24
BIOS Setup Information
Panel Scaling (Optional)
Select the LCD Panel scaling option used by Internal Graphic device
Choices: Auto, Centering, Stretching.
South Cluster Configuration
25
BIOS Setup Information
PCI Express Configuration
PCI Express Configuration Settings
PCI Express Root Port 1-4
Control PCI Express root port
Choices: Enable, Disable.
26
BIOS Setup Information
USB Configuration
USB Configuration settings
XHCI Mode
Mode of operation of XHCI controller
Choices: Enable, Disable.
XHCI Link Power Management
Enable/Disable XHCI Link Power Management
Choices: Disable, Enable.
USB OTG Support
Enable/Disable USB OTG Support
Choices: Disable, PCI Mode, ACPI Mode.
EHCI Controller
Control the USB EHCI (USB2.0) functions. One EHCI controller must always be enabled.
Choices: Enable, Disable.
USB Per-Port Disable Control
Control each of the USB ports (0~3) disabling
Choices: Disable, Enable.
27
BIOS Setup Information
USB Port #0-#3 Disable
Disable each USB port (0~3).
Choices: Enable, Disable.
Audio Configuration
Audio Configuration Settings
LPE Audio Support
Select LPE Audio ACPI mod or PCI mode.
Choices: Disable, LPE Audio PCI mode, LPE Audio ACPI mode.
Audio Controller
Control Detection of the Azalia device
Disabled = Azalia will be unconditionally disabled.
Enabled = Azalia will be unconditionally enabled.
Choices: Disable, Enable.
28
BIOS Setup Information
SATA Drives
Press<Enter> to select the SATA Device Configuration Setup options.
Chipset SATA
Enables or Disables the Chipset SATA Controller. The Chipset SATA controller supports the 2
black internal SATA ports (up to 3Gb/s supported per port).
Choices: Enable, Disable.
SATA Test Mode
Test Mode Enable/Disable
Choices: Enable, Disable.
Chipset SATA Mode
IDE: Compatibility mode disables
AHCI support: Supports advanced SATA features such as Native Command Queuing.
Warning: OS may not boot if this setting is changed after OS install.
Choices: IDE, AHCI.
Serial Port 0/1 Hot Plug Capability
If enabled, SATA port 0/1 will be reported as Hot Plug capable.
Choices: Enable, Disable.
29
BIOS Setup Information
LPSS & SCC Configuration
LPSS & SCC Mode
LPSS & SCC Devices Mode Settings.
Choices: ACPI Mode, PCI Mode.
SCC SD Card Support
SCC SD Card Support Enable\Disable.
Choices: Disable, Enable.
Miscellaneous Configuration
30
BIOS Setup Information
Enable/Disable Misc. Features
State After G3
Specify what state to go to when power is re-applied after a power failure (G3 state)
Choices: S0 State, S3 State.
SMM LOCK
Enable/Disable SMM Lock feature. It will lock the SMRAM and unable load SMM driver any
more.
Choices: Disable, Enable.
PCI MMIO Size
PCI MMIO Size
Choices: 2GB, 1.5GB, 1.25GB, 1GB.
NGFF Card Inserted
Set ‘YES’ If NGFF Card is Inserted
Choices: No, Yes.
UHPAM Card Inserted
Set ‘YES’ If UHPAM Card is Inserted
Choices: No, Yes.
Security Configuration
31
BIOS Setup Information
TXE
Choices: Disable, Enable.
TXE HMRFPO
Choices: Disable, Enable.
TXE Firmware Update
Choices: Disable, Enable.
TXE EOP Message
Send EOP Message Before Enter OS
Choices: Disable, Enable.
TXE Unconfiguration Perform
Revert TXE settings to factory defaults
Choices: [No], [Yes]
32
BIOS Setup Information
4.4
Others
33
BIOS Setup Information
SIO Configuration
Serial Port1
Choices: Disable 3F8/IRQ4.
Watch Dog Timer Select
Choices: Disable, 15 secs, 30 secs, 1 min, 2 mins, 3 mins.
Power Control
Choices: Former State, Always On, Always Off.
34
BIOS Setup Information
Hardware Monitor
35
BIOS Setup Information
APM Configuration
Power On By RTC Alarm
Choices: Disable, Enable.
RTC Alarm Date
Choices: Every day, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23,
24, 25, 26, 27, 28, 29, 30, 31.
Wake up hour
Choices: 0-23
Wake up minute
Choices: 0-59
Wake up second
Choices: 0-59
Wake on LAN1
Choices: Disable, Enable.
36
BIOS Setup Information
4.5
Security
Set Supervisor Password
Set or clear the Supervisor account’ password.
Supervisor Hint String
Press Enter to type Supervisor Hint String.
Set User Password
Set or clear the User account’ password.
Supervisor Hint String
Press Enter to type User Hint String.
Min. password length
Set the minimum number of characters for password (1-20).
37
BIOS Setup Information
4.6
Boot
Boot Priority Order
Keys used to view or configure devices: ↑ and ↓ arrows Select a device. ‘+’ and ‘-‘move
the device up or down. ‘Shift + 1’ enabled or disables a device. ‘Del’ deletes an unprotected
device.
38
BIOS Setup Information
4.7
Exit
Exit Saving Changes
Equal to F10, save all changes of all menus, then exit setup configure driver. Finally resets
the system automatically.
Exit Discarding Changes
Equal to ESC, never save changes, then exit setup configure driver.
Load Setup Defaults
Equal to F9. Load standard default values.
Discard Changes
Load the original value of this boot time. Not the default Setup value.
Save Changes
Save all changes of all menus, but do not reset system.
39
Troubleshooting
Chapter 5
Troubleshooting
This chapter provides a few useful tips to quickly get PCOM-B632 running with success. As
basic hardware installation has been addressed in Chapter 2, this chapter will primarily focus
on system integration issues, in terms of BIOS setting, and OS diagnostics.
5.1
Hardware Quick Installation
ATX Power Setting
Unlike other Single board computer, PCOM-B632 supports ATX only. Therefore, there is no
other setting that really needs to be set up. However, there are only two connectors that must
be connected—J25 (4 pins ATX power connector) & J31 (20 pins ATX Power Connector) in
the PCOM-C600 carrier board.
Serial ATA
Unlike IDE bus, each Serial ATA channel can only connect to one SATA hard disk at a time;
The installation of Serial ATA is simpler and easier than IDE, because SATA hard disk
doesn’t require setting up Master and Slave, which can reduce mistake of hardware
installation.
The PCOM-B632 can support two SATA interface (SATAII, 3.0Gb/s) to the PCOM-C600
carrier board with AHCI or IDE mode. It has two J28 & J30 SATA ports in PCOM-C600
carrier board.
40
Troubleshooting
5.2
BIOS Setting
It is assumed that users have correctly adopted modules and connected all the devices
cables required before turning on ATX power. 204-pin DDR3 Memory, keyboard, mouse, SATA
hard disk, VGA connector, power cable of the device, ATX accessories are good examples
that deserve attention. With no assurance of properly and correctly accommodating these
modules and devices, it is very possible to encounter system failures that result in
malfunction of any device.
To make sure that you have a successful start with PCOM-B632, it is recommended, when
going with the boot-up sequence, to hit “F2” key and enter the BIOS setup menu to tune up
a stable BIOS configuration so that you can wake up your system far well.
Loading the default optimal setting
When prompted with the main setup menu, please scroll down to “Load Setup Defaults”,
press “Enter” and select “Yes” to load in default optimal BIOS setup. This will force your BIOS
setting back to the initial factory configuration. It is recommended to do this so you can be
sure the system is running with the BIOS setting that Portwell has highly endorsed. As a
matter of fact, users can load the default BIOS setting any time when system appears to be
unstable in boot up sequence.
5.3
FAQ
Information & Support
Question: I forget my password of system BIOS, what am I supposed to do?
Answer:
You can switch off your power supply then find the JP20 of the PCOM-C600
carrier board to set it from 1-2 short to 2-3 short and wait 5 seconds to clean
your password then set it back to 1-2 short to switch on your power supply.
JP20:CMOS Setting
Jumper Setting Describe
*1-2
Default
2-3
Clean CMOS
41
Troubleshooting
Question: How to update the BIOS file of the PCOM-B632?
Answer:
1. Please visit web site of the Portwell download center as below hyperlink
http://www.portwell.com.tw/support/download_center.php
But you must register an account first. (The E-Mail box should be an existing
Company email address that you check regularly.)
http://www.portwell.com.tw/member/newmember.php
2. Input your User name and password to log in the download center.
3. Select the “Search download” to input the keyword “PCOM-B632”.
4. Find the “BIOS “page to download the ROM file and flash utility.
5. Execute the zip file to root of the bootable USB pen drive. You can
get the“ShellFlash32.efi”,”temp.bin”,”Update.nsh” three files.
6. Insert your USB pen drive in USB port of the PCOM-C600 carrier
board and power-on.
7. Boot to EFI-Shell mode then input the “fs0:” command to switch to
the root of the USB pen drive.
42
Troubleshooting
8. Type the”update” command to start flash BIOS processes.
9. When it finished all update processes, it will reboot in 5 seconds automatically.
43
Troubleshooting
10. Please press the “F2” key to BIOS setup menu to select “Load
Setup Defaults” and then select “Exit Saving Changes” option to finish all BIOS
flash processes.
Question: What are the attention options when insert PCOM-B632 in PCOM-C600 carrier
board?
Answer: 1. The PCOM-C600 carrier board doesn’t support the DP display function in Win8
operation system. It must use the PCOM-C605 carrier board which can support
the DP display function.
2. It you want to use the eDP display function, it needs to use a PA-M1V
display adapter (optional) and need to modify a customized version BIOS to
enable the DP option of the BIOS. If you need to use this adapter, please ask
your PCOM-B632 provider or distributor.
Note:
Please visit our Download Center to get the Catalog, User manual, BIOS, and driver
files.
http://www.portwell.com.tw/support/download_center.php
If you have other additional technical information or request which is not covered in
this manual, please fill in the technical request form as below hyperlink.
http://www.portwell.com.tw/support/problem_report.php
We will do our best to provide a suggestion or solution for you.
Thank you.
44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement