Installation Manual
VX3012
7" Single DIN Multimedia Receiver
DVD / Built-in BT Technology /
iPhone® iPod® / USB / AV In
INSTALLATION GUIDE
What’s in the Box
The following items are supplied
with the VX3012:
•
•
•
•
•
•
•
•
VX3012HeadUnit
Trim Ring
Hardware Bag
Power/Speaker Output Harness
Remote Control
External Microphone
MountingSleeve& RemovalKeys
Installation Guide
Tools and Supplies
The following tools and supplies
are needed to install the VX3012:
• Torx type, flat-head and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screw
driver, socket wrench set or other
tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.
Optional Equipment
Steering Wheel Control Interface (SWC) - The VX3012 is compatible with various PAC, Metra and iDatalink Maestro SW
steering wheel control adapters.
Disconnect the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VX3012 is to be installed in a car equipped with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Replacing the Fuse
When replacing the vehicles radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating
could damage the unit and cause a fire.
ISO-DIN Installation
The VX3012 is designed to fit into a 1.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may
be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to
mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of
installation.
1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.
2.Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer
screws may damage components inside the chassis.
Dash Board
Rubber Sheath
3. Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve. Follow
the wiring diagram carefully and make certain all connections
are secure and insulated with wire nuts or electrical tape. After
completing the wiring connection, plug the connector into the
mating socket on the rear of the chassis. Turn the unit on to
confirm operation (vehicle ignition switch must be “ON”). If
the unit does not operate, re-check all wiring until the problem
is corrected.
4. Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
Mounting
The rear of the unit
Trim plate
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal
laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation flexibility. This unit will fit into most import dashes with little or
no modification to the dash board/cavity. Some US domestic vehicle dashes will accept a Single-DIN chassis, but there is usually a
small gap between the radio and dash piece after installation is complete. In this case, use the trim ring to conceal any gaps that
may be present.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the
unit is mounted within this limitation.
2
Wiring Diagram
CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions
carefully, or have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.
AUTO ANTENNA
MONITOR
SWC A
White/Purple
White/Purple
SWC B
White/Brown
White/Brown
SWC GND
Brown/Black
Brown/Black
BLACK - ANTENNA
YELLOW RCA - REAR CAMERA
BLACK 1MM WIRE - BT ANTENNA
PINK - PARKING BRAKE (-)
AUX2 R
AUX2 L
AUX2 VIDEO IN
YELLOW
POWER ANTENNA / AMP REMOTE - BLUE (+)
REVERSE - GREEN / WHITE (+)
MOBILE POWER AMP
Some vehicles may not support all SWC functions. Professional Installation is recommended.
YELLOW - VIDEO OUT
BLACK 3.5MM - BT MICROPHONE
BATTERY
GND
BATTERY (+)
GROUND (-)
IGNITION SWITCH
IGN / ACC (+)
ORANGE - TFT DIMMER (+)
3
BACKUP
CAMERA
SWC ADAPTER CABLE
Voxx Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 800-323-4815
www.jensenmobile.com
© 2015
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement