High Speed Network Dome Camera

Quick Start Guide

Ax63Z

SAFETY

When installing your Ax63Z camera be sure to avoid:

• excessive heat, such as direct sunlight or heating appliances

• contaminants such as dust and smoke

• strong magnetic fields

• sources of powerful electromagnetic radiation such as radios or TV transmitters

• moisture and humidity

• areas with mechanical vibrations

• fluorescent lamps or objects that reflect light

• unstable light sources as this may cause flickering

• temperatures below -40° Celsius or -40° Fahrenheit and above 50° Celsius or 122°

Fahrenheit

.

POWER SUPPLY

Ensure the supplied voltage meets the power consumption requirements of this camera before powering the camera on.

Ax63Z power consumption requirement: Indoor - PoE+ (IEEE 802.3at) or AC24V; Low temperature outdoor - AC24V only. PoE+ power is supported in indoor installations only.

Maximum power consumption for outdoor installations with heater on: 36W

Incorrect voltage may cause irreparable damage to the video camera and will effectively void the camera warranty.

CLEANING

• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft, dry cloth to remove finger prints or dust from the dome cover.

• Use a blower to remove dust from the lens.

• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent, then wipe dry.

• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may damage the surface finishes.

CAMERA PARTS AND DEFINITIONS

Safety

Wire

SERVICING

To avoid electrical shock and to preserve the product warranty, DO NOT disasemble the camera.

Refer servicing to qualified personnel only.

PACKAGE CONTENTS

In addition to this manual and a fully assembled camera, the dome camera packing box includes:

1. Blind set screw

2. Hex driver (Allen key)

3. Torx driver (Torx key)

4. RJ45 Female/Female Coupler

1 2 3 4

Please Note: Scan the QR code to the right or visit www.i3international.com to view and download the full User Manual for this camera. Also available for download is the

AnnexxusConfigurationTool or ACT program used to locate and configure your cameras with your SRX-Pro software. This program is already installed in SRX-Pro v3.3.3.69 and higher. Please contact our Technical Support team if you have any questions or concerns regarding camera installation or you require software services or support. Technical support can be reached by email at:

[email protected] or by phone toll free 1.877.877.7241.

INSTALLATION

Main signal connector

1. Remove the dome cover

2. Remove the EPE

3. Using a soft lint-free cloth, wipe the dome cover clean and remove fingerprints

4. Attach camera housing

5. Turn on the camera

6. Mount the camera (basic options presented below)

7. Connect the camera to a power source AC24V for indoor or outdoor installations; or PoE+ for indoor installations only. (For reliable PoE please use i3 switches S81, S243, or S242)

Caution: Some switches may have compatibility issues, in this case the camera will require AC24V.

8. Connect control inputs to terminals GND, Alarm in, Alarm out, Audio in, Default and Reset

9. Connect camera to DVR

QR Code to Complete

User Manual / ACT i3-TRNG-CAMSAx63Z-QuickGuide .indd

Rev. 160929

QUICK START GUIDE

PENDANT PIPE MOUNT

1. Remove ceiling support frame and attach connector ring to the aluminum tube in clockwise direction.

2. Mark the ceiling matching 4 mount holes on ceiling support frame.

3. Drill 4 holes, hammer 4 wall screws into holes.

4. Secure entire ceiling support frame to screw mounts.

5. Fasten connector ring to wall hang support.

6. Thread cabling of main unit through short aluminum tube and push cables out from bottom.

7. Pull out cables and connect main unit to connector ring in clockwise direction. Use hex key to secure set screw to connector ring and fasten safety cable to tube.

High Speed Network Dome Camera Ax63Z

CONNECT CAMERA TO i3 SRX-PRO SERVER

Connection Type 1:

Crossover direct connection

i3 SRX-Pro Server

LAN

Connection Type 2:

Via Gigabit Switch

i3 SRX-Pro Server

WALL MOUNT

1. Remove the secure plate and drill 4 holes on wall matching mount holes on plate.

2. Hammer 4 screw mounts into holes and secure plate.

3. Fasten connector ring to wall hang support in clockwise direction.

4. Thread cabling of main unit through aluminum tube and push cables out from bottom.

5. Pull out cables and connect main unit to connector ring in clockwise direction

6. Use hex key to secure set screw to connector ring and fasten the safety cable to tube.

PARAPET WALL MOUNT

1. Remove the secure plate and drill 8 holes on wall matching mount holes on plate.

2. Hammer 8 screw mounts into holes and secure plate.

3. Fasten connector ring to L tube in clockwise direction.

4. Thread cabling of main unit through aluminum tube and push cables out from bottom.

5. Pull out cables and connect main unit to connector ring in clockwise direction

6. Use hex key to secure set screw to connector ring and fasten the safety cable to tube.

7. Insert entire tube including main unit into hole fitting on secure plate

8. Rotate tube 180 degrees clockwise with secure plate and fasten screws.

Camera’s default IP: 192.0.0.16.

FW ver. ANNEXXUS 63Z.0.1.4670 | Login: admin

FW ver. ANNEXXUS 63Z.0.1.5025, or higher | Login:

/ PW: 1234 i3admin / PW: i3admin

1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.

2. Change the IP address on the onboard NIC (LAN) (or on NIC1 if your SRX-Pro

Server has two onboard NIC cards) of your SRX-Pro Server to 192.0.0.XXX to match the default IP range of your Annexxus IP camera.

3. Connect your camera to i3 SRX-Pro Server (see diagram above).

4. Turn on your Annexxus camera.

5. It may be necessary to download and install AnnexxusConfigTool (ACT) from our website (www.i3international.com). Follow the ACT installation instructions until the application has been successfully installed on your SRX-Pro Server. For SRX-

Pro v3.3.3.69 and above ACT is already installed.

6. Either double-click i3 Annexxus Configuration Tool icon on the desktop to launch the ACT application or click the “ACT Config Tool” button on the IP Camera Tab in SRX-Pro.

7. The application window will appear displaying a list of active network cameras.

Remember: Annexxus Cameras cannot share an IP address, each camera requires its own unique IP address.

8. Select desired camera in the Annexxus Finder software by double-clicking it in the list and click Edit.

9. Enter the new IP address and Subnet Mask of the camera in the Change IP

Address area. The new camera IP address must match the original range of your

SRX-Pro LAN or NIC1 card.

E.g. If your original SRX-Pro Server’s IP address was 192.138.10.122, change your Annexxus camera’s IP address to 192.138.10.XXX.

10. Enter the default camera password the Input Password field and click Save.

11. Wait a few moments for a successful confirmation window. Click OK to close it.

12. Repeat Steps 8-11 for all detected Annexxus cameras in the Annexxus Finder.

13. Make sure you can connect to the camera through Internet Explorer:

a. Launch Internet Explorer and enter the IP Address you have just assigned to your Annexxus camera. The password window should be displayed.

b. Enter the default camera User Name and default Password.

c. Annexxus camera interface will be displayed in the Internet Explorer window. You should be able to see the camera image on the screen.

If you do not see the camera image on the screen, call i3 International tech support for troubleshooting tips: 1.877.877.7241

14. Make sure that the latest version of GiPi updater is installed on your SRX-Pro

Server. You can download the updates from ftp://files.123ip.com/drivers/gipi.

Please contact i3 Technical Support team for access information.

15. Once the latest GiPi updater has been installed, restart i3 SRX-Pro Server software.

16. Log In and go to the Setup -> IP Camera tab.

17. Click the Search button to display connected Annexxus cameras.

18. Select the detected camera in the list and click Select.

19. In the Select IP Camera window, enter the default camera User Name and

Password, then click Add.

20. The selected camera will be added to the IP Camera list.

Don’t forget to assign the IP camera to the SRX-Pro video channel in the corresponding column.

21. Your Annexxus camera is now connected to SRX-Pro Server and is ready to record. You may change resolution and frame rate for the Annexxus camera in the IP Camera tab menu or you may choose to configure the camera’s advanced settings.

i3 INTERNATIONAL INC.

1.866.840.0004

www.i3international.com

U.S.A 1967 Wehrle Drive, Suite 1,

PMB# 034 Buffalo NY, 14221

Canada 780 Birchmount Road, Unit 16,

Scarborough, ON, M1K 5H4