LW2702/LW2902 Quick Start Guide
under 15 minutes
under 30 minutes
over 60 minutes
under 60 minutes
Router
Wireless VIDEO MONITORING System
LW2710/LW2910 Series
quick start guide
Hand Tools
Time
Tools
Hardware
Hi Speed
Skills - Easy
Skill Level
SIMPLY AWARE
Under 20 Minutes*
NOTE: AVOID INSTALLING IN A LOCATION WHICH REQUIRES THE
WIRELESS SIGNAL TO PASS THROUGH CEMENT, CONCRETE AND METAL
advanced
STRUCTURES.
THIS WILL REDUCE THE TRANSMISSION RANGE.
Router
* Installation time may vary
based on application and
camera location
Hand Tools
™
Plug & Play connections, Intermediate
easy
On screen set up
Skill Level
Getting Started
*
This wireless digital security system
comes with the following components:
• LCD monitor with built-in recorder and
wireless receiver*
• Color two-way audio outdoor cameras*
• Camera Stand(s)*
A. Camera Setup
1
• Audio/video cable
Connect the antenna by
turning it clockwise onto the
receiver’s antenna jack.
• Mounting hardware kit(s)*
• Instruction manual
4
2
4
Connect one end of the camera Power
Adapter to the camera and the other
end to an electrical outlet.
Connect power adaptor to local
120V AC power outlet.
PIR motion sensor
3
Plug the included stand
into the slot as shown
below. Turn the stand
counter-clockwise until
it clicks into place. For
different viewing angles,
rotate the stand further.
Connect one end of the
receiver power adaptor to
the bottom of the receiver
and the other end to an
electrical outlet.
• CD
*
Secure Camera to the mounting stand.
advanced
Adjust the angle
of the camera until the
desired view is set.
Tighten the thumbscrews to secure the
desired camera position.
Intermediate
NOTE: Wireless cameras require a power source to operate.
NOTE: When adding cameras that were not included in the original
box, you will need to pair up the camera with the receiver. Please
refer to the camera pairing section of the User Manual.
NOTE: This camera includes an Auto Mechanical IR Cut Filter.
When the camera changes between day/night lighting, an audible
clicking noise may be heard coming from the camera. This clicking is
normal, and indicates that the camera filter is working.
• USB cable
Monitor size, number of cameras and
SD card capacity may vary by model.
Check your package for specific content
information.
3
IMPORTANT: The motion detection
range is up to 21ft (6.5m) to minimize
false alarms. Keep this in mind when
selecting suitable installation location.
The LCD Receiver can be setup for use on a tabletop, or mounted to a wall or underneath a counter or cupboard. See the User Manual for full mounting details.
• Tabletop stand
• Power adapters (for receiver
& camera[s])*
Attach the included
easy
antenna to the camera
by
screwing it on to the side
as shown below.
B. LCD Receiver Setup
• Remote control
• Wireless antennas (for camera [s])*
2
NOTE: Before you install a camera, carefully plan where
and how it will be positioned, and where you will route
the cable that connects the camera to the power adaptor.
Before starting permanent installation, verify its performance
by observing the image on a monitor when the camera is
positioned where it will be permanently installed. Cameras
are rated for indoor/outdoor installation. Not intended for
direct exposure to rain or snow. For outdoor applications
install under shelter protected from the elements
1
• SD memory card*
Mount camera stand to
the wall.
ATTENTION: Make sure to first connect the camera(s) to
an electrical outlet before powering on the receiver; this will
ensure a proper connection.
5
Insert the included SD card into
the SD Card slot on the LCD
receiver until you hear a “click.”
The card will not be flush when
completely inserted.
NOTE: The receiver is compatible
with most major brands of SD card
up to 16 GB.
Slide the power switch
to the “ON” position.
NOTE: For the
LW2710 Series,
the switch is located
on the back of the
screen.
LW2710 Series
6
Adjust the antenna on the
receiver as necessary to
provide the clearest
reception.
LW2910 Series
NOTE: For the
LW2910 Series, the
switch is located on the
side of the screen.
NOTE: If one or more of the cameras do not appear when selected (i.e. Camera 2 is turned on but does not appear on channel 2),
follow the pairing process as described in user manual.
www.lorextechnology.com
LW2710/LW2910 Series Quick Start Guide_R1
Page 1
Wireless VIDEO MONITORING System
LW2710/LW2910 Series
quick start guide
C. Basic System Setup
NOTE: This system supports a USB connection
to your PC to enable remote monitoring using
Skype™. Refer to the user manual for detailed
set-up instructions.
Remote Control
Follow these steps to access the Menu screen and make
updates/changes to settings:
1. 1/Play/Pause
2. Confirm Setting
3. 4/Rewind
4. MENU/ Back
5. Record Motion/
Start/Stop
6. Volume
7. Quad View
8. 2/Fast Forward
9. 3/Stop
10. Scan/Delete
11. Channel
Autoscan/Manual
12. AV Output
1. Press the MENU button to enter the Menu screen
2. Use the directional buttons to highlight a menu item
3. Press ENTER to enter the highlighted menu item
4. Use the directional buttons to change highlighted setting
5. Press ENTER to save a setting change (If you press MENU instead,
the setting change will NOT be saved)
6. Press MENU to go back to the previous menu. Press MENU
repeatedly to go back to camera view mode.
Setting Date/Time:
Set the date and time to ensure that they are properly captured
on recordings
1. Press MENU. Highlight SETTING menu and press ENTER
2. Highlight DATE & TIME and press ENTER
3. Press RIGHT / LEFT to move the cursor and UP / DOWN to
change the value for the date and time
4. Press ENTER to save setting. Press MENU to return to previous menu
Changing Camera View Mode
View a single camera at a time, single cameras in sequence
(Auto Sequence) or all cameras at the same time (Quad). Follow
these steps to access each of the viewing modes:
Single Channel View: Press CHANNEL-M repeatedly to
manually scroll through available camera channels (turn unused
channels off in CAMERA ON/OFF menu)
Auto Sequence View (default setting): Press CHANNEL-A
to automatically scroll through every available channel at 5 second
intervals. Press CHANNEL-M to return back to manually switching
camera channels
Quad View: Press the QUAD button once to enter 4-channel
quad view. Press again to return to the previous camera view. To
quickly go to a specific channel while in Quad view, simply press
the corresponding directional button (1-4). Once you have exited
Quad view, return to using MANUAL-M to manually scroll to
specific channel
Three recording modes are available on the system: Manual Recording, Schedule Recording, and Motion
Recording.
NOTE: The system can record video to an SD card one channel at a time. You should always format the SD
card prior to initial recording. For details refer to the owner’s manual section “Format”.
NOTE: Recording overrides other actions on the receiver. You must stop recording on the system in order to
perform other actions, such as opening the Main Menu, Quad Mode, etc.
TIP: Beeping Sound
Mode
Description
HOW TO OPERATE
Manual Recording
• Continuous recording from one camera
• Cannot record while in Quad mode
• Cannot record while in Auto Sequence
Viewing Mode
• Press the RECORD • button on the
remote control to start/stop manual
recording
SCHEDULE RECORDING
• Continuous recording from one camera or from
Auto Sequence
Viewing Mode (system will record from one
camera at a time)
• IMPORTANT: Turn off Manual
Recording and Motion Recording to
enable Schedule Recording
• Enter a Start and Stop Time from Main
Menu > Record > Schedule Record
• Cannot record while in Quad mode
MOTION RECORDING
(AUTO)
• System only records when motion is detected by
a camera
• Compatible with Quad Mode (recommended) –
enable Quad Mode
BEFORE turning on Motion Recording
• Compatible with Auto Sequence Viewing Mode
• Press the Motion button on the remote
control to start/stop Motion recording
SCREEN SAVER +
MOTION RECORDING
• Enable Screen Saver for LCD receiver to simulate
a picture frame
• System only records when motion is detected by
a camera
• Press the Motion button to start Motion
Recording
• Press the Scan/Del button to enable
Screen Saver mode
On-Screen Display (see user manual for further details)
1
4
2
5
6
3
7
1.
2.
3.
4.
Signal Indicator
Recording Status Indicator
File Name
Camera indicator
For information on viewing recordings, refer to the user manual section “Viewing Recorded Video”
5. New Recording/
Memory Full indicator
6. SD card status indicator
7. Current Time/
Date Indicator
Intercom Feature
By default, the system is set to beep when motion is detected
by the camera(s). To turn the beeping off, follow these steps:
1. Press MENU. Highlight SETTING menu and press ENTER
2. Highlight ALARM VOLUME and press ENTER
3. Press LEFT directional button repeatedly to move volume
to the lowest setting (1 bar)
4. Press ENTER to save setting
™
D. How to begin Recording?
(using remote control)
Navigating Menu Screens:
SIMPLY AWARE
Use the Intercom feature for two-way
communication between the LCD receiver and the
camera. Talk to the person at the camera from
behind closed doors for added security. Refer to
the user’s manual, section “Using the Intercom”
NOTE: Please make sure the camera(s) is
properly connected prior to using the Intercom.
www.lorextechnology.com
©2011 Lorex Technology Inc.
This product is expandable up to 4 cameras.
To order additional cameras, please visit our website at
www.lorextechnology.com
It’s all on the Web
For detailed setup information, please refer to your User’s
Manual. For additional information and accessory purchases, please visit our website
www.lorextechnology.com/support
Extending Your Wireless Signal
Even with a clear line-of-sight between your camera(s) and your receiver, you may experience a lower frame
rate simply due to the distance between your wireless devices. Accessory antennas are available that can
help extend the range of your wireless signal. Visit www.lorextechnology.com for more details.
As our product is subject to continuous improvement, Lorex Technology &
subsidiaries reserve the right to modify product design, specifications, prices
& warranty without notice and without incurring any obligation. E&OE
LW2710/LW2910 Series Quick Start Guide_R1
Page 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement