Model 4280/4280-8 Installation Instructions

Model 4280/4280-8 Installation Instructions
V’STii, XM
-
GENERAL
FORMAT
ANDDIPSWITCH
TABLESHAVEBEENREVISED
INTHISISSUE.
0
4280/4280-8
INSTALLATION
INSTRUCTIONS
GENERAL
INFORMATION
RANGE
The 4280/4280-8. RF Receiver can
rreceive,+‘ signals. from *wireless
component of the VISTA XM
system which reccgnixes alarms,
transmitters within a nominal range of
200 feet. This provides greater
status messages and keypad
tixpandability ,in insrallations where
cmtrol messages from ALERT Ill.,
(5700 series) trafism.itters at 345 .:’ :’ haid, *ire might’ not be feasible. By
usirq ::?wo Receivers, the #fective
M!=?z(U.S.A)‘. (The 428014280-8 is* :
rapge ican ,be increased to suit the
nob compatible with Alert II (560$! ,
These
needi of a particular installation.
series) transmitters..).
messages are processed and
IMPORTANT!
The Receiver
relayed to the VISTA XM Cbntd
‘! must be mounted a minimum 01
panel via & P-wire polling loop.
10 feet from tho Control and
Using a 4280 allows expafisiiirk up- :
other
,electronic
equlpment.
to. 63 zones, plus a Wireless
.’ Mountlitg
closer than 10 feei
keypad (5727). .-.;The 4280-8
can
result
In
RF
supports 8 zones, plus a wireless
communlcatlpti
.f(eIlures
- keypad (5727).
between the transmitters
and
To r muse ALERT Ill
wkeless
Receivir,
due to’ Interference
transmitters with the VISTA XM
from
the
Cci-ntrol’s
system, a 4171X1-X,! dialer board,
micropiocessor.
and a 4152LMB loop module ‘must be
NOTE: The 4280-8 Receiver is
installed in the Control, and either one
identical to the 4280, except that it
or twc 4280s (or 428008s, if only 8
supports
up tc 8 zones only. To avoid
wireless zones are required) must be
confusion, the term ‘Receiver is used
connected to the polling loop. Note
in this document to collectively
that the 4280 and 4280-8 each draw
represent
both the 4280 and 4280-8
40mA current. tf two Receivers ata
Receivers.
J
used, power for the second Receiver
should be taken” from the auxiliary
power connection on the main Control.
315 MHz in Canada
INTRODUCTION
The 4280/4280-8 RF Receiver is a
l
0
.
VISTA
m
(STANDARD)
-20
;’
TOADD~OPW
2-WlE
f\. .
.
-
1c-JJ
\ _,’
RECEIVER SUPERVlSlON
1. If the cover of the Receiver is
removed, an ALARM or TROUBLE will
be displayed depending upon the
response programmed in the Control.
2. If the connection is broken
between the Receiver and the Control,
an ALARM or TROUBLE will be
displayed depending on the response
programmed in the Control. This
response is usually that of a
DAY/NIGHT or 24 hour type.
3. tf, within a programmed interval of
time, the Receiver does not hear from
any of its transmitters, an ALARM or
TROUBLE will be displayed depending
on the response programmed in the
Control. The interval is programmed in
field 130.
4280 HOUSE IDENTlFlCATlON
The Receiver -responds only to
transmitters with the same house ID
(DIP switch programmable from Ol31).
This
prevents
system
interference from transmitters in other
nearby systems. To make sure you do
not choose a House ID that is in use
nearby, put the system in the Sniffer
Mode, which is described later in this
document.
to the separate DIP Switch Tables at
included with the VISTA XM Control)
TRANSMITTER SUPERVISION
Each transmitter (except 5701 and
5727) automatically transmits a
check-in signal to the Receiver at 7090 minute intervals. H the Receiver
does not hear at least one Check-in
signal from a transmitter within a
programmed interval (4-30 hours; field
1*31), the console will display that
transmitter’s ID number and the word
ZHECK..
Each transmitter (including 5701 and
5727) is also supervised for bw battery
conditions, and will transmit a low
battery signal to the Receiver when the
battery has approximately 30 days of
life remaining. The console will beep
once every 60 seconds, and display
the transmitter’s ID number and the
words ‘LO BAT (5130XMI5137) or
“BAT- (413OXM4137).
NOTE: After replacing a low or dead
battery, activate the transmitter and
enter the security-code + OFF. at the
control to clear its memory of the low
battery signal.
TRANSMITTER
IDENTIFICATION
Each transmitter is assigned its own
unique ID number (Zone #; DIP switch
programmable).
Whenever
a
transmission takes place; either for
an alarm, fault, check-in or low
battery, ,this ID number is sent along
with the message to the Receiver
which, in turn, relays this information
to the control panel, which displays
the condifion and zone number on the
console.
GOR/WlNoOW
TFIANSMITTER
5711wM
WIRELESS
PANIC
BUITON
5101
-30
--
CONFIGURATIONS
SINGLE RECEIVER
A single 4280 RF receiver can
uniquefy identify up to 64transmitters
within a nominal 200’ range, without
hard-wiring a large premises, and is
suitable for many installatiins.
2 RECEIVERS I REDUNDANCY.
For additional
security,
some
installations
might warrant
a
redundant configuration. Thii means
that 2 receivers, connected to the
same 2qire polling loop, are used and
set to the same house ID. Each of
these receivers listens to all of the
transmitters on the job, but if one
receiver happens to fail or is
sabotaged, or a path from one or more
transmitters is inadvertently blocked
by a metal object, the other one will
still be there to detect alarms, and
faults,
and to supervise
the
transmitters. Both 4280s (or 42808s)
are fully supervised so that if one
does fail or is deliberately sabotaged,
you’ll know about it.
SINGLE WIRELESSRECEIVER
USING lW0 RECEWERS TO
INCREASE COVERAGE
For installations where the area to.be
protected goes well beyond the 200’
range of the system, or the building
configuration prevents getting the
rated range in all paths to
transmitters, a second receiver can
be installed. The first 4280 is located
at one end of the premises and the
second 4280 at the other with both
4280s connected to the same 2-wire
polling loop.
IMPORTANT: tf two 4280s used:
.* Both must be at least 10 feet from
each other, as well as from the Vii
XM Control panel and remote consoles.
One of the 4280s or 4280-8s must be
powered from auxiliary power.
The house IDS must be the same.
Using two Receivers does not
increase the number of transmitters
(63
the system can support
transmitters, plus a wireless keypad).
l
l
l
TWO WIRELESSRECEIVERS
REDUNDANT CONFlGURATiON
WIRELESS ZONE TYPES
Each RF zone can be programmed to
respond as any zone type such as
.
ZONETYPE
Entry/Exit Burg
Perimeter Burg
IRAN~R
ID t
1 through 63 l
1 through 63 l
1 through 63 l
ENTRY/EXIT,
INTERIOR,
interior Burg
PERIMETER, etc. (refer to the VlSTA
XM Technical Reference Manual for a
complete explanation of each zone
type). Alarm responses as follows:
NOTES:
(silent or audible) 162 - 63%” (6701)
Transmitters set for an ID of 32
,Day/Night Burglaryl 1 through 63
through 47 will have a 3 minute lock24 Hour Auxiliin I 1 throuah 63
out between transmissions.
* Transmitter IDS48 through 55 have
highest signal prior&.
n Transmitter IDS 62 and 63 are unsuperv&ed to albw removal of the 6701 off
premises - signal priority is bwer than fire, but higher than burglary.
l
!
l
l
l
l
PROGRAMMING & DISPLAYS
Each Receiver and transmitter used
must be enabled as an RF device
when programming the control. In
addition, two supervisory check-in
intervals and various other RF options
must be programmed. Refer to the
VISTA XM Technical Reference
Manual for complete programming
information.
A display of *CHECK” ~mpanied by
a display of one or more zone ID
numbers indicates that a problem
exists with the transmitters assigned
to those zones. First check that the
zones are intact and make them so if
they are not. If the problem has been
corrected, enter the code + Off to
clear the display.
A display of ‘CHECK” accompanied by
zone ID 88, 89,90 or 91 indicates a
problem with the Receiver. Refer to
the Technical Reference Manual for
troubleshooting information.
A display of ‘LO BAr’ (‘BAT for
4130XMI4137) and a zone ID
indicates a low battery condition in
that transmitter.
A display of l 4280 SET UP ERROR’
(“E8” for 413OXMI4137) indicates that
a 4280-8 Receiver is being used in a
system with more than 8 RF zones
programmed. ff thii is not corrected,
none of the zones in the system will
be protected. tf more than 8 RF zones
are desired, a 4280 Receiver must be
used.
-
INSTALLATION
RECEIVER
Location: The Receiver should be
bcated in a central indoor location,
such that optimum RF signal reception
from transmitters can be obtained ( a
high location in the premises is best).
. The approximate
range
for
transmitters is 200 feet. Do not mount
the Receiver to a metal wall, post or
girder, and avoid locating near large
metal objects such as refrigerators,
ranges, storage cabinets, etc.
IMPORTANT!
The Receiver must
be at least 10 feet from the control
panel or any remote consoles to avoid
their
from
interference
microprocessors.
Wiring:
Run the Control’s polling
loop wiring to the 4280(s) using
twisted
pair wire, and make
connections to the terminals as
shown on page 9, making sure polarity
is correct. Depending upon whether
or not the polling loop can support the
current drain of the Receiver will
determine if the wire run is a 2- or 4
wire run.
Maximum polling loop wire runs are as
follows: #22 gauge @6SV max
#20 gauge @950’ max
#18 gauge @18OO’max
#16 gauge @ 2400’ max
NOTE: The maximum combined
polling loop run is 4000’. ff using
shielded wire, the maximum is 2OW.
CAUTION: ff an intercom system is
being used, the polling loop wires
must be as far from the intercom
wiring as possible (minimum 67. If this
spacing cannot be accomplished,
shikied wire must be used, otherwise
interference on the intercom system
might occur. Also note that the
maximum total wire supported is cut in
half when shielded wire is used.
Blue Jumper: If two Receivers are
used, cut the BLUE jumper on the
second Receiver. This identifies it as
the 2nd Receiver at the control panel.
Power: Each Receiver draws 4OmA
for its operation. The number of other
devices being supported by the
polling bop and their individual current
drains will determine if the Receiver
can draw its power directly from the
are usBd,
polling loop. /f2 Rec8iims
at hst one must draw its pwer from
tie wnrro~s allxii&uy power output
If the polling loop current’s capacity
will be exceeded, run an additional
pair of wires from the control’s 12VDC
auxiliary power output to the
Receiver’s auxiliary power terminals.
In this case, the 4280 derives its DC
power primarily from the auxiliary
power source (signal communication
is via the polling loop terminals).
CAUTION : To avoid possible
damage to the Receiver, do not
connect auxiliary power to the polling
loop terminals.
Antenna: Attach the antenna to the
antenna terminal as shown. Note that
in some earlier models, a two piece
antenna was supplied, along with
separate instructions for installation.
Snlffer
Mods
Select
Receiver House &:O To avoid
interference from nearby systems,
set the DIP switches in the Receiver
for House ID WO’-(all switches up),
then enter your ‘Installer Code’ + [#) +
121. Note that if two Receivers are
being used, both must be set to ID
%O’. The Receiver will now ‘sniff’ out
any House IDS in the area and display
them at the console. Keeping the
Receiver in this mode for about 2
hours will give a good indication of the
House IDS being used. To exit the
Sniffer Mode, key your installer code
+ Off. Set the Receiver’s House ID to
one not displayed in the Sniffer Mode.
!t-?
‘. :
TRANSMITTERS
‘.
Battery
Switches/
DIP
Set each
Installation:
transmitter’s House ID and unique
transmitter ID number using the
transmitter’s DIP switches and
referring to the DIP Switch Tables at
the end of this document. Install the
required battery for each transmitter.
Verify
,Mode
to
Sniffer
Transmitter
House
IDS: To
check that ali transmitters have been
set for the proper house ID, set the
Receiver to the proper house ID and
enter the Installer code + [#] + [3].
Fault each transmitter to cause a
transmission and check that each
transmitter’s ID number is displayed
at the console in turn. To exit the
Snider Mode, simply key your installer
code + Off.
Transmitter
Locations:
Before
mounting each transmitter, first verify
that the proposed location is suitable
for radio transmission by using the
Go/No Go test. When a suitable
location is determined, mount each
transmitter in accordance with its
instructions.
Advisories
Do not place transmitter on or near
metal objects, as this will decrease
range and/or block transm’&ions.
When connecting a door/window
contact to a 5711.5711 WM, or 5715
transmitter, avoid a wire length of 2024 inches. This particular length
decreases range. A shorter or longer
length has no effect
Go/No
Go Test (Patented):
This mode helps determine the best
location for each transmitter and is
activated by putting the system in the
TEST mode (security code + [S)) and
removing the Receiver’s cover. The
Receiver’s sensitivity is reduced by
half. Once transmitters are placed in
their desired locations and the
approximate length of wire to be run to
sensors is connected
to the
transmitter’s screw terminals, open
circuit each transmitter. Do not
conduct this test with your hand
wrappedamundthe transmitrer.
tf a single Receiver is used, the
transmitter ID will be displayed, and
the console will beep three times to
indicate signal reception. If two
Receivers are used, the keypad will
beep -once if the first received the
signal, twice if the second received
the signal and three times if both
Receivers heard the signal.
tf the console does not beep, reorient
or move the transmitter to another
location; Sometimes moving the
transmitter only a few inches may
mean the difference
between
successful
and unsuccessful
transmissions.
To exit this mod-a, replace the
Receiver’s cover, then enter the
installer code and press Off. Note
that the Receiver’s sensitivity is fully
restored when the cover is replaced.
TESTING
THE
SYSTEM
Power up the entire system and put it
in the TEST mode.
Check the
Check the operation of the 5727
wireless keypad by using it to
operation of all wireless transmitters
perform
by faulting and restoring each
wireless sensor. The control panel
console should beep l-3 times
(depending on whether 1 or both
4280s received the transmission) for
each fault, and the ID number for the
device should be displayed. The
display should disappear as the
transmitter sensor is restored. Exit
TEST mode.
all
keypad
functions.
;l-)
‘\ :
including arming, disarming, chime.
mode, use of temporary codes and
panic keys.
IONS
Physical:
Ekctr+l:
4.e (117mm)
7.6” (193mm);
16.6” (419mm) with antenna
Depth: 25 (64mm)
Vottage: 7-l 1 votts (with lkH2 mod&Gin from an Ademco
poiw hop)
7-14VDC from auxiliary power source.
Current: 46mA
Width:
Height:
TURNING THE SYSTE‘M OVER TO THE USER
1. Explain the significance of the CHECK and LO BAT d&lays and what should
be done when they appear.
2. Encourage the user to find and remedy any unintentionally faulted transmitter
so as to avoid having to bypass them when arming the system.
3. instruct the user in bow to change transmitter batteriis and bow to clear the
LO BAT display, should it appear. Make sure the user understands the
importance of changing a transmitter battery within 30 days after a LO BAT
display appears (within 7 days for transmitters that are activated on a
frequent daily basis). Transmitter operation is unpredictable when battery
voltage is iow, and may result in runaway transmissions, which can block
reception of other transmitters.
Preferably, battery replacement may be scheduled and done by the service
company, at least at the rated end of life of the battery or after a LO BAT
message appears, whichever occurs sooner.
{c----l
\ i’
House ID
SWltChSOltingfCKAll
Dwiw6 Except 6716
DIP SWITCH TABLES FOR WIRELESSDEVICES
6701 hnicxmtr.
h
1
Po6.6: w.jQITRlo62
d, rXUTRlD63
lm7Keypd
EGa
000
000
m
u.
t
musEID
(1 snsww,
1
12345
/,
XumID
6ldrn
UP
mil
dn
cl
sd
(Or)
DIP SWlTCH TABLES FOR WIRElESS DEVICES
6711m11w
DoorlwhdowTrpnrmrtter
6715
Uniuer8alXmtr.
r---j
’
-a-n’
ms. 1:UPI NORWREsPoN6E XM lo PO6o:l$. g.
t=-swomu)
e . FAST RESPONSE
(kdd IO32& ilit
Pos.2:uP~NocwERTAyPER
d? . CQvER TANPER @moN.C. 6-q)
- 10 -
N.O.)
DIP SWITCH TABLES FOR WIFELESS DNlcES
TRU%NfT--.
0
1
664311
7
10
11
I
lb
~
- 11 -
WARNING
THE LlMt7ATlONS OF THIS ALARM SYSTEM
Vhiie this system is an advanced design security system, it does not offer
uaranteed protection against burglary, fire or other emergency. An alarm
ystem, whether commercial or residential, is subject to compromise or failure to
ram for a number of reasons. For example:
Intruders may gain access through unprotected openings or have the
technical sophistication to bypass an alarm sensor or disconnect an alarm
warning device.
Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and
many other sensing devices will not work without power. Battery opera&d
devices will not work without batteries, with dead batteries, or if the batteries
are not put in properly. Devicespowered solely by AC will not work if their AC
power supply is cut off for any reason, however briifly.
Signals sent by wireless transmitters may be blocked or reflected by metal
before they r8aCh the alarm receiver. Even if the signal path has been
recently checked during a weekly test, biockage can occur if a metal object is
moved into the path.
A user may not be able to reach a panic or emergency button quickly 8nOugh.
T8i8phone lines needed to transmit alarm signals from a premises to a central
monitoring station may be out of service or temporarily out of senrice.
Telephone lines are also subject to compromise by sophisticated intruders.
While smoke detectors have played a key role in reducing residential fire
deaths in the United States, they may not activate or provide early warning for
a variety of reasons in as many as 35% of all fires, according to data
published by the Federal Emergency Management Agency. Some of the
reasons smoke detectors used in conjunction with.this System may not work
are as follows. Smoke detectors may have been improperly installed and
positioned. Smoke detectors may not sense fires that start where smoke
cannot rsZ5h the detectors, such as in chimneys, in walls, or roofs, or on the
other side of closed doors. Smoke detectors also may not sense a fire on
another. level of a residence or building. A second fbor detector, for example,
may not sense a first fbor or basement fire. Moreover, smoke detedors have
sensing limitations. No smoke detector can sense every kind of fire every
time. in general, detector’s may not always warn about .fir8S caused by
carelessness and safety hazards like smoking in bed, violent explosions,
escaping gas, improper storage or flammable materials, overbaded electrical
circuits, children playing with matches, or arson. Depending on the nature of
the fire and/or the location of the smoke [email protected], the detector, even if it
operates as anticipated, may not provide sufficient warning to allow all
occupants to escape in time to prevent injury or death.
- 12 -
pj
_’
f-?
./
WARNING
THE LIMITATIONS OF THIS ALARM SYSTEM (cont.)
b Passive Infrared Motion Detectors can only detect intrusion within the
designed ranges 85 diagrammed in their instajiation manual. hssive
Infrared
Detectors do not provide volumetric area protection. They do create multiple
beams of protection, and intrusion can only be detected in unobstructed
areas covered by those beams. They cannot detect motion or intrusion that
takes place behind walls, ceilings, floors, closed doors, glass partitions,
glass doors, or windows. Mechanical- tampering, masking, painting or
spraying of any material on the mirrors, windows or any part of the optical
system can reduce their d8t8Ction ability. Passive Infrared Detectors sense
changes in temperature; however, as the ambient temperature of the
protected area approaches the temperature range of 90’ to 150°F, the
detection performance can decrease.
Alarm warning devices such as sirens, bells or horns may not alert people or
wake up sleepers who are bcat8d on the other side of a closed or partly open
doors. tf warning device sound on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the
bedrooms. Even persons who are awake may not hear the warning if the alarm
is muffle by noise from a stereo, air conditioner or other appliances, or by
passing traffic. Finally, alarm warning devices, however loud, may not warn
hearing-impaired people or waken deep sleepers.
Even if the system responds to the emergency as intended, however,
OCCUpantSmay have insufficient time to prOt8Ct themselves from th8
emergency situation. In the case of a monitored alarm system, authorities
may not respond appropriiteiy.
This equipment, liie Other eie&iCal devices, is subject to component failure.
Even though this equipment is designed to last as long as 10 years, the
electronic components could fail at any time.
he most common cause of an alarm system not functioning when an intrusion or
Ire occurs is inadequate maintenance. This alarm system should be tested
v88kly to make sure ali sensors are working properly.
Mailing an alarm system may make one eligible for lower insurance rates, but
in alarm system is not a substiiut8 for insurance. Homeowners, property owners
md renters should continue to act prudentty in protecting themS8lv8s and
ontinue to insure their lives and property.
Ye continue to deV8iOpnew and improved protection devices. users of alarm
systems owe it to th8mSetV8S and their bV8d ones t0 iearn about these
l8veiopments.
- 13 -
“FEDERAL
COMMUNICATIONS
COMMISSION
(FCC) STATEMENT”
This equipment has been tested to FCC requirements and has been found
aoCeptabi8
for Use. fhe FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed
and used properly, that is, in strict accordance with the manufacturefs
instructions, may cause interference to radio and television reception. It has
been typ8 tested and found to comply with th8 limits for a Class B computing
device in accordance with the specifications in Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonabie protection against such
interferenc8 in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. lf this equipment does
cause interference to radio or television reception, which can be determined by
turning the equipment off tind on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ff using an indoor antenna, have a qualify outdoor antenna installed.
Reorient th8 receiving antenna until interference is reduced or eliminated.
Move th8 receiver away from the kc8iver.
Move the antenna leads away from any wire runs to the Receiver. \
Plug the Receiver into a different outlet so that it and the radio or n! are on
different branch circuits.
If necessary, the user should consult the deaier or an experienced
radioheievision technician for additional suggestions.
fhe user or installer may find the foliowing bookiet prepared by the Federal
Communications Commission helpful:
‘Interference Handbook’
This booklet is available from the U.S. Government Printing Office, Washington,
DC 20402. Stock No. 004-000-0045Q-7.
The user shall not make any changes or modifications to the equipment unless
authorized by the Installation Instructions or User’s Manual. Unauthorized
changes or modifications could void the user’s authority to operate the
(-1
\. .:
l
l
l
l
l
- 14 -
r! ,
-
NOTES -
-
- 15 -
ADEMCO LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Piiay Corporation, and its
divisions, subsidiaries and affiliates (Sellef),
165 Eileen Way, Syosset, New
York 11791, warrants its products to be in conformance with its own plans and
specifications and to be free from defects in materials and workmanship under
normal use and service for 18 months from the date stamp control on the produd
or, for products not having an Ademco date stamp, for 12 months from date 01
original purchase unless the installation, instructions or catalog sets forth a
shorter period, in which case the shorter period shall apply. Seller’s obligation
shall be limited to repairing or replacing, at its option, free of charge for materials
or labor, any product which is proved not in compliance with Seller’s
specifications or proves defective in materials or workmanship under normal us8
and service. Seller shall have no obligation under this Limited Warranty OI
otherwise if the product is aftered or improperly repaired or senric8d by anyone
other than Ademco factory service. For warranty service, return product
transportation prepaid, to Ademco Factory Service, 165 Eileen Way, Syosset,
.
New York 11791.
THERE ARE NO WARRANTIES,
EXPRESS OR IMPLIED, OF
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR
OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THlS OR ANY
OTHER WARRANTY, EXPRESSOR IMPLIED, OR UPON ANY OTHER BASIS OF
LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY
THE SELLERS OWN NEGLIGENCEOR FAULT.
Seller does not represent that the products it sells may not be compromised or
circumventsd; that the products will prevent any personal injury or property loss
by burglary, robbery, fire or otherwise; or that the products will in all cases
provide adequate warning or protection. Customer understands that a properly
installed and maintained alarm may only reduce th8 risk of a burglary, robbery,
fir8 or Other events occurring without providing an alarm, but it is not inSUranc8or
a guarantee that such will not occur or that there will be no personal injury or
Droperty loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER
LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR
INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMlTED
rNARRANTV OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN,
SELLER’S MAXIMUM LlABlLlTY SHALL NOT IN ANY CASE EXCEED THE
PURCHASEPRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND
%CLUSIVE REMEDY AGAINST SELLER. This warranty replan= any previous
Hairanties and is the only warranty made by Seller on this pxKkJCt.No increase
>r alteration, written or verbal, of the obligations Of this Limited Warranty is
authorized.
ALARM DEVICE MANUFACTURINO AONeONOF~YCQIS#eOW
16S Eileen Way, Syosset, New Vork 11791
NISOlV4
lOi91
Copyright 0 lW0 PlI7WAY CORPORMION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement