Owner`s Manual
IMPORTANT INFORMATION
Carefully read this instruction manual before you install or
use your portable air conditioner. Please retain this
manual for product warranty and for future reference.
MODEL:
DIMC10RC / DIMC12RC / DIMC15RC
INSTRUCTION MANUAL
CAUTION
1. Make sure the inlet and outlet vents are never blocked.
2. Ensure the appliance is on a stable, even surface when operating to avoid water
leakage.
3. Do not operate this unit in an explosive or corrosive atmosphere.
4. When switched to cooling, only operate this unit in ambient temperatures between
17°C and 43°C. For heating, only operate this unit in ambient temperatures
between 5°C and 23°C.
5. Clean the air filter frequently to ensure efficient operation.
6. To prevent compressor damage when the unit has been operating and is turned off,
please wait at least 3 minutes before restarting.
7. This unit needs to be plugged into a 220-240V ~ 50Hz AC, 10 Amp power outlet.
8. Do not use any extension cords with this unit.
9. This unit is for indoor operation only.
10. Open the adjustable air vent and extend the exhaust pipe (and drain pipe, if fitted) to
the closest window before using.
11. Only ever have a professional technician, manufacturer or service agent replace a
damaged power cord.
12. The batteries from the remote control must be removed and disposed of safely,
before the appliance is scrapped.
13. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
14. Children should be supervised to ensure that they do not play with the appliance.
Important.
PORTABLE AIR CONDITIONER
The air conditioner must always be stored and
transported upright. In case of doubt we suggest you
wait for at least 24 hours before operation.
(Please keep unit upright at all times)
1
PACKAGE CONTENTS
CONTROLS AND DISPLAY
Portable air conditioner
DIMC10RC
Remote control
Batteries for remote control
Extendable window kit
Water tray
PARTS
1.
Controls
2.
Remote receiver
3.
Adjustable air vent
4.
Window kit adaptor
5.
Exhaust tube
6.
Upper drain plug
7.
Cool air inlet
8.
Cool air filter
9.
Hot air inlet
DIMC12RC/ DIMC15RC
1. POWER
10. Hot air filter
Press the POWER button to turn the unit "ON" or "OFF".
※ The portable air conditioner is fitted with a compressor delay protection circuit. This
11. Lower drain plug
protects the unit from possible damage due to rapid starting and stopping of its
compressor. Compressor operation begins 3 minutes after the unit is switched on or the
mode is switched from dehumidify to air conditioning.
2. FUNCTION
Press this button to select cooling, heating or dehumidification.
※ When the heating or dehumidification functions are used the upper drain plug (6) must be
Note: Make sure drain plugs (6 and 11) are fitted before use.
2
removed and a drain hose must be attached.
3
3. TEMP+
In cooling function, this button raises the set temperature by 1°C each
7. TIMER
ON/OFF button for the programmable timer.
The timer can be used to turn the unit on automatically after a set
time it is pressed to a maximum of 30°C. In heating function, this button
time delay is complete.
raises the set temperature by 1°C each time it is pressed to a maximum
1. With the unit OFF, press the "TIMER" button to set the desired time
of 25°C.
delay before the unit is to start.
4. TEMP-
In cooling function, this button lowers the set temperature by 1°C each
2. Choose the function desired (cooling, heating or dehumidification.)
time it is pressed, to a minimum of 17°C. In heating function, this button
3. Once the set time delay is complete, the unit will turn on
automatically.
lowers the set temperature by 1°C each time it is pressed to a minimum
4. If you press the “POWER” button before the time delay is complete,
of 15°C.
the delay will be cancelled and the unit will turn on immediately.
※ The time taken to reach the desired set temperature will depend on the environment and
The timer can be used to turn the unit off automatically after a set
the size of the space in which the unit is operating in.
time period is complete.
For example, if the ambient temperature is too hot or the room is too large, the rate at
which the temperature descends will be slow as the cooling may be less effective.
1. With the unit ON, press the "TIMER" button to set the desired time
for the unit to remain on.
5. DISPLAY
The display indicates the current, the set temperature or the timer
2. Once the set time period is complete, the unit will turn off
setting. When the timer or temperature is adjusted, the new setting is
automatically.
3. If you press the “POWER” button before the time delay is complete,
shown then the display returns to the current set temperature.
the delay will be cancelled and the unit will turn off immediately.
※ The display is also used to show error codes should a fault occur, see ERROR CODES.
6. SPEED
Press SPEED to select LOW, MEDIUM, HIGH or AUTO fan speed.
If AUTO fan speed is selected, the unit operates at maximum capacity
and high fan speed while the room temperature is more than 2°C from
8. SLEEP
Press the SLEEP button to select the sleep comfort mode.
When the unit is cooling and sleep mode is selected, the unit will raise
the set temperature 1°C each hour to a maximum of 2°C over two hours.
the set temperature. When the room temperature is within 2°C of the set
temperature, the unit operates at medium capacity and fan speed. Once
the room temperature equals the set temperature, the unit will operate
When the unit is heating and sleep mode is selected, the unit will lower
the set temperature 1°C each hour to a maximum of 2°C over two hours.
at minimum capacity and low fan speed to efficiently maintain the
These temperatures will be maintained for the balance of the time set
desired temperature.
and help maximize sleep comfort.
When HIGH, MEDIUM or LOW speed is selected, the unit operates at
When setting the "sleep comfort" mode, please ensure that you set the
maximum capacity until the set temperature is reached. The fan
operates at the selected speed.
number of hours required by using the TIMER function. The hours set
will be shown on the display by pressing either the TEMP+ or TEMPbuttons.
4
5
REMOTE CONTROL
INSTALLATION
Unpacking the unit.
1.
Remove the exhaust tube from its storage under the
rear air outlet. Replace the rear air outlet.
2.
Install the exhaust tube by rotating it clockwise onto
the rear air outlet. Please ensure it is fully inserted
before use.
Locating the unit.
Install the portable air conditioner in a flat location
with adequate space to ensure the air inlets and
outlets will not be blocked.
Keep a minimum clearance of 50cm from walls and
other objects. Locate the unit to allow the exhaust
POWER
ON/OFF switch
FUNC
Function selector
TIMER
Timer programming
AUTO
Automatic fan speed
Avoid sharp bends or kinks in the exhaust pipe.
HI
High fan speed
The optional adjustable window slider is included to
MID
Medium fan speed
ensure the exhaust pipe is held in place (in the
LOW
Low fan speed
window) and prevents expelled hot air re-entering
SLEEP
Sleep comfort mode selector
the room.
c
Raise Set Temperature
d
Lower Set Temperature
6
pipe and drain hose to reach a suitable window, as
shown.
The appliance should not be used in damp areas such as a laundry or bathroom.
Do not place the unit where it will be in direct sunlight as it may overheat and turn off.
7
ADJUSTABLE WINDOW SLIDER KIT
WATER DRAIN (Error code E4)
The adjustable window slider kit is installed as shown below.
When the air conditioner is used, excess water condensation may be produced that cannot be
removed via the exhaust hose. This water is captured by an internal container. When this
container is full, the unit will stop working and display the E4 error code.
When the error code E4 is displayed the water collected in the internal container must be
manually drained:
1.
Switch off and unplug the unit.
2.
Move the unit to a suitable place to drain the water.
Consider placing a tray or suitable container under the
outlet pipe to catch the drained water.
HEATING AND DEHUMIDIFICATION
When the heating or dehumidification functions are used the upper
drain plug (6) must be removed and a drain hose must be attached.
3.
Remove the lower drain plug (11), refer to parts illustration.
4.
Slightly tilt the unit to the rear to drain the water.
5.
Replace the drain plug.
Make sure the drain plug is re-fitted to the drain outlet before
use.
Extend the exhaust to the window before the unit is restarted.
HEATING
When using the heating function move the rear air outlet with the exhaust tube to the front of
the unit as below:
The outlet exhaust must still be attached to the window when using the heating function.
Return the outlet and tube to the rear of the unit for cooling or dehumidification.
8
9
MAINTENANCE
CARE OF THE UNIT
WARNING: ALWAYS UNPLUG THE UNIT BEFORE MOVING OR CLEANING.
1.
Only plug the unit into a suitable 220-240V~ 50Hz AC 10 AMP power supply.
2.
Hold the plug when unplugging the unit, never pull on the cord.
CLEANING
3.
Do not place the unit in direct sunlight. This can fade the plastic case.
Air filters
4.
Do not operate the unit in a confined space.
The air filters located on the rear of the unit can be removed simply by pulling the filter frame
5.
Do not place objects on top of the unit. This blocks the air outlet.
slightly out and then across to the side.
6.
Do not place the unit where the air inlets or outlets may be blocked by curtains or
furniture.
7.
Keep the filters clean.
OVERHEAT PROTECTION
This unit is fitted with an overheat prevention device. If the unit overheats it will automatically
turn off. The unit can be restarted after 30 minutes.
ERROR CODES
Error codes are shown on the display should a fault occur.
Cabinet
Wipe with a damp cloth and polish with a soft cloth.
E1: Indicates open circuit or short circuit in the room temperature sensor.
E2: Indicates open circuit or short circuit in the pipe temperature sensor.
E4: Indicates the internal water container is full. Refer to WATER DRAIN.
If error code E4 persists, please contact an authorized service centre.
10
11
TROUBLE SHOOTING
WARRANTY
Never try to repair or dismantle the air conditioner yourself. Unauthorized repairs may
The warranty period is 24 months from the date of purchase.
result in the loss of warranty and can endanger the user and their property.
Problem
The air conditioner
does not operate.
Cause
Solution
No power supply.
Connect to a functioning power
supply socket and switch on.
Error code E4 is shown,
indicating the internal water
container is full.
The start timer function is
active.
The air conditioner is in direct
sunlight.
Windows or doors are open.
Empty the internal water
container.
(Refer to WATER DRAIN)
Press the POWER button to
deactivate the TIMER function.
Close the curtains.
The filters are dirty.
Clean the filters.
The air inlets or outlets are
blocked.
The room temperature is
below the set temperature.
Remove the blockage.
The air conditioner
is noisy.
The air conditioner is not
level.
Place the air conditioner on an
even, solid surface.
The compressor
does not work.
The overheat protection is
activated.
The remote control
does not function.
The distance between the
remote control and the air
conditioner is too great.
Wait 30 minutes until the
temperature has decreased,
then turn the air conditioner on
again.
Note: Compressor operation
begins 3 minutes after the unit
is switched on.
Move closer to the air
conditioner. Aim the remote
control directly at the control
panel.
The air conditioner
does not seem to
operate efficiently.
The batteries are flat.
Glen Dimplex Australia Pty Ltd
Glen Dimplex Australasia Ltd
Unit 1, 21 Lionel Road.
38 Harris Road, East Tamaki,
Mount Waverley VIC 3149.
Manukau, Auckland 2013
Australia
New Zealand
Ph: 1300 556 816
Ph: (09) 274 8265
Fax: 1800 058 900
Fax: (09) 274 8472
Web: www.dimplex.com.au
Web: www.dimplex.co.nz
Close windows and doors.
Lower set temperature.
DISPOSAL
•
•
•
Do not dispose of electrical appliances as unsorted municipal
waste. Use separate collection facilities.
Contact your local government for information regarding the
collection systems available.
If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the ground water, polluting the
food chain and damaging health and well-being.
Replace the batteries.
If you have any issues with your unit, please contact Glen Dimplex for
your nearest service agent.
Proof of purchase is required at the time of service.
12
13
SPECIFICATIONS
Model No.
DIMC10RC
DIMC12RC
Power Source
220-240V ~ 50Hz AC
220-240V ~ 50Hz AC
Power Consumption
1245W / 1090W
1452W / 1246W
Rated Power
1280W / 1100W
1480W / 1300W
(EN60335)
Cooling / Heating
Capacity
3000W / 3000W
3500W / 3500W
Air Flow
360 M3/H
450 M3/H
Moisture Removed
40 L/DAY
60 L/DAY
Refrigerant
R410A
R410A
Min. room size
10m2
10m2
Max. room size
22m2
25m2
Dimensions (mm)
300W x 507D x 627H
300W x 550D x 760H
Net Weight
28KG
29.5KG
Model No.
DIMC15RC
Power Source
220-240V ~ 50Hz AC
Power Consumption
1826W / 1566W
(EN14511)
(EN14511)
Rated Power
1700W / 1500W
(EN60335)
Cooling / Heating
Capacity
4400W / 4400W
Air Flow
550 M3/H
Moisture Removed
75 L/DAY
Refrigerant
R410A
Min. room size
10m2
Max. room size
29m2
Dimensions (mm)
300W x 550D x 760H
Net Weight
31.5KG
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement