HKTS 18 OM - Mikrocontroller.net
harman/kardon
SUB-TS18
(HKTS 18 SUBWOOFER)
SERVICE MANUAL
harman/kardon, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797
Rev1
4/2007
harman/kardon
SUB-TS18
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . . . . ……………………………………. . . . 1
DETAILED SPECIFICATIONS. . . . . . . . . . . . . .. . . . . . . . . ………………….. …2
PACKAGING. . . . . . . . . . . . . .. . . . . . . ……………………… . . . . .. . .. .. .. . . . . 4
CONTROLS & CONNECTIONS . . . . . . . . . . . . . .. . . . . . . . . ………………….. 5
SPEAKER CONNECTIONS……………………….………..……. . . .. . .. . . . .. . .. 6
OPERATION……. . . . . .. . . . . . . . .. .. . . . .. .. . . . . ………………………………10
TEST PROCEDURE. . . . . . . . . . . ………………………………………………….11
UNIT EXPLODED VIEW. . . . …………… ……………. .. ………... . . .. .. ... . … . 12
AMPLIFIER EXPLODED VIEW. . . . ………………... . .. ………... . . .. . . .. . .… . 13
BLOCK DIAGRAM . . . . . . . . . . . . . .. . . . . . . ……………… . . . . .. . .. . .. . . . . 14
DETAILED TROUBLESHOOTING..…………………………………………………15
PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ……… . …………. . . . .. .. .. . .. . . . 16
ELECTRICAL PARTS LIST …………. .... . .. . . . …………………………... … . . 20
SEMICONDUCTOR PINOUTS . . . .. .. .. .. . . . .. . ……………..………..………. .24
SCHEMATIC DIAGRAMS . . . . . . . . .. .. .. .. . . . .. . ………………………..……. .25
SPECIFICATIONS
Amplifier Power (RMS)
200 Watts
Driver
10" (254mm) woofer, Bass Reflex Enclosure
Inputs
Stereo Line Level, dedicated Subwoofer (LFE)
and Speaker Level with gold-plated binding posts
Outputs
Speaker Level with gold-plated binding posts
Frequency Response
35Hz – 120Hz (Filter switch ON)
35Hz – 450Hz (Filter switch OFF)
External Trigger Input Voltage:
3-30 Volts AC/DC
Dimensions (H x W x D)
18-7/8" x 13-3/8" x 13-3/8" (479mm x 340mm x 340mm)
Weight
35.1 lb/15.8kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications
unless otherwise stated.
1
harman/kardon
SUB-TS18
HKTS 18 Sub 200W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120vac/60Hz
Parameter
Amp Section
Yes/No
Yes
Hi/Lo Line
108-132
Nom.
120
Nonimal
Specification
Unit
QA Test
Limits
Unit
Vrms
Notes
Normal Operation
Notes
Conditions
Bridge type amplifier, None of the
speaker terminals must be
connected to system GND at any
time.
n/a
Ohms
Watts
%
%
mV-DC
n/a
n/a
150
0.1
0.5
20
Nominal
50 - 250 Hz, 1 input driven, limiter off
22k filter
22k filter
@ Speaker Outputs
16
n/a
10
Measured at amplifier board
Input Sensitivity
Input Frequency
Line (L&R) Input
SUB (LFE) Input
50
220
125
Hz
mVrms
mVrms
Speaker/Hi Level Input
3.4
Vrms
2.4 - 4.8
Hi Level Max. Input Voltage
32
Vrms
30
Nominal Freq., Min. Volume
Signal to Noise Ratio
SNR-A-Weighted
SNR-unweighted
SNR rel. 1W-unweighted
85
62
64
dB
dB
dB
82
59
59
Residual Noise Floor
1.2
mVrms
3.0
Residual Noise Floor
0.8
mVrms
2.0
relative to rated power
relative to rated power
relative to 1W Output
Volume @max, using RMS
reading DMM/VOM (or A/P)
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
freq.+ harmonics)
10K
4.7K
ohms
ohms
n/a
n/a
Nominal
Nominal
160
270
25
Hz
Hz
Hz
2.0
%
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
THD @ Rated Power
THD @ 1 Watt
DC Offset
Damping factor
Input Impedance
Line Input (L, R,LFE)
Speaker/Hi Level Input
Filters
L&R Fixed Low-Pass Filter
SUB (LFE) Low pass Filter
Subsonic filter (HPF) 3rd Order
Limiter
THD at Max. Output Power
Features
Auto - On -Off Selection Switch
Phase Switch
Filter On/Off Switch
Volume Pot Taper (Lin/Log)
Speaker Out
2-Color LED power indicator
Power Switch
Fuse Holder
D
3.5
200
0.08
0.15
5
YES
0-180
YES
LOG
YES
YES
YES
YES
deg
n/a
Nominal Freq.
154 - 308 To Rated Power
87 - 175 To Rated Power
To Rated Power
140 - 180 @ -6dB ref. 100Hz
240 - 300 @ -3dB ref. 100Hz
22 - 28 @ -3dB ref. 30Hz
Measured at the speaker at speake
output terminals on the amp board.
Single input driven
SUB (LFE) input driven only
(20 dB below Line In), Single input
driven
A-Weighting filter
22k filter
22k filter
3rd order fixed
2nd order fixed
3rd order fixed
5.0
functional
functional
functional
functional
functional
functional
functional
functional
Refer to ATO section
A Taper
Binding post connector L&R
Blue: On, Amber: Stand-by
Input Configuration
Line In (L,R)
SUB (LFE)
Speaker/Hi Level In
YES
YES
functional
functional
Dual RCA jack
RCA jack
YES
functional
Binding post connector L&R
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input test frequency
ATO Level Line & SUB Input
ATO Level Speaker in
YES
50
4.0
35
Hz
mV
mV
0.9
sec.
ATO Turn-on time
functional Auto - on selection switch in Auto
n/a
"
2.0 - 6.0
"
20 - 50
"
Amp connected and AC on, then
functional input signal applied
2
harman/kardon
SUB-TS18
Nonimal
Specification
Parameter
Amp Section
Unit
QA Test
Limits
Conditions
5 - 17
Time before muting, after signal is
removed
ATO Turn-OFF Time
12
minutes
Power on Delay time
3
sec.
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
5
500
500
mV-peak
mV-peak
mV-peak
Notes
functional AC Power Applied
10
700
700
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Efficiency
Stand-by Input Power
Power Consumption @ rated power
8
Watts
12
@ nom. line voltage
240
Watts
250
@ nom. line voltage
Maximum allowable input power
under nominal input voltage and
frequency, in stand-by mode (HOT
or COLD operation).
200 Watts @ 3.5 ohms and
nominal line voltage
Protection
Short Circuit Protection
functional Direct short at output
YES
Thermal Protection
YES
functional
DC Offset Protection
Primary Fuse Rating
YES
functional DC present at Speaker Out leads
USA-Domestic
3.15
Amps
n/a
3
Type-T or Slo Blo (no DENTORI
Amplifier should resume operation
after short circuit condition is
removed.
Any user accessible metal parts
should always remain at 65 degree
C or less for domestic version or 55
degree C or less for EU version.
Relay or crowbar (for driver/fire
protection),
User-replacable fuse with
UL/SEMCO rated holder.
harman/kardon
SUB-TS18
4
harman/kardon
SUB-TS18
SUB-TS18 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
¡ Subwoofer-Level Control
™ High-Cut (Low-Pass) Filter Switch
£ External Trigger Input
¢ Audio-Sense On/Off Switch
∞ Phase Switch
§ Line-Level Subwoofer (SUB) Input
¶ Line-Level Full-Range Inputs
• Speaker-Level Outputs
ª Speaker-Level Inputs
‚ Master Power Switch
⁄ AC Power Cord
¡ Subwoofer-Level Control: Volume
may be adjusted using the SubwooferLevel Control. Turn the control clockwise
to increase the SUB-TS18’s volume, or
counterclockwise to decrease it.
inefficiency and distortion. Engage this filter
when using the Speaker-Level Inputs ª,
or when using the Line-Level Full-Range
Inputs ¶, unless your receiver or processor
processes its line-level output using a lowpass filter. The filter has no effect when the
SUB Input § is used.
or DC) is detected, the SUB-TS18 amplifier
will turn on, even when the audio-sense
feature has been activated by placing the
Audio-Sense On/Off Switch ¢ in the
AUTO position. The amplifier will remain
on for about 10–15 minutes without a
trigger signal.
£ External Trigger Input: Use the supplied mini-plug cable to connect the trigger
output of another product to this jack. When
a trigger signal between 3 and 30 volts (AC
¢ Audio-Sense On/Off Switch: When
placed in the AUTO position, and when the
Master Power Switch ‚ is turned on, the
SUB-TS18 will automatically turn itself on or
™ High-Cut (Low-Pass) Filter Switch:
Placing this switch in the ON position activates circuitry that cuts out all audio input
signals above 120Hz, allowing the SUB-TS18
to focus its power on reproducing the lowfrequency portion of the signal, avoiding
5
HKTS 18 OM
10/6/06
1:34 PM
Page 6
harman/kardon
SUB-TS18
SUB-TS18 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
place itself in the Standby mode, depending on
whether it is receiving an audio signal. When
this switch is placed in the ON position, the
SUB-TS18 will remain on, whether or not it is
receiving an audio signal.
An LED located on top of the SUB-TS18
indicates whether the SUB-TS18 is in the On
or Standby state when used with the AudioSense On/Off Switch ¢ in the AUTO
position. The LED is lit blue to indicate that
the SUB-TS18 is receiving an audio signal
and is turned on, and the LED is lit amber to
indicate that no signal is being received and
the SUB-TS18 is in the Standby mode.
When the Audio-Sense On/Off Switch ¢
is in the ON position, the LED will be lit
blue, whether or not an audio signal is
present.
When the Master Power Switch ‚ is
turned off, the LED goes dark, no matter
which position the Audio-Sense On/Off
Switch ¢ is in.
∞ Phase Switch: This switch determines
whether the SUB-TS18 subwoofer’s pistonlike action moves in and out in phase with
the main speakers. If the speakers were to
play out of phase, the sound waves produced by the subwoofer would be canceled
out, reducing bass response. This phenomenon depends in part on the relative placement of the speakers in the room. In most
cases, the Phase Switch ∞ should be left
in the NORMAL position. However, it
does no harm to experiment with the Phase
Switch ∞, and you may leave it in the
position that maximizes bass response.
§ Line-Level Subwoofer (SUB) Input:
Connect the subwoofer output of a receiver
with digital surround sound decoding, such
as Dolby® Digital or DTS®, to this input. This
input bypasses the SUB-TS18’s internal
crossover circuitry, and should only be used
with a filtered signal. If your receiver does not
have digital decoding, you should use the
Line-Level Full-Range Inputs ¶ instead.
¶ Line-Level Full-Range Inputs: Connect
the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these
inputs. If your receiver does not have a separate subwoofer output, use a Y-adapter (not
supplied) to bridge the receiver’s preamp output to the main amp input for that channel,
and connect the long end of the adapter
to the corresponding line-level input on the
SUB-TS18. If your receiver has only a single
subwoofer output, you may connect it to
either the left or right line-level input on the
SUB-TS 18, and no Y-adapter is needed.
• Speaker-Level Outputs: If you are
using the Speaker-Level Inputs ª on the
SUB-TS18, you should connect these bindingpost terminals to your front left and right
speakers, remembering to maintain polarity
by connecting the (+) terminal on the
SUB-TS18 subwoofer to the (+) terminal
on the speaker, and the (–) terminal on the
SUB-TS18 subwoofer to the (–) terminal
on the speaker. If you are not using the
Speaker-Level Inputs ª, then connect
your front left and right speakers directly
to your receiver or amplifier. See pages 9
through 12 for further information on speaker
connections.
6
ª Speaker-Level Inputs: If your receiver
or amplifier does not have a line-level subwoofer output, connect these binding-post
terminals to the main left and right speaker
terminals of your receiver or amplifier.
Remember to maintain polarity by connecting
the (+) terminal on the receiver/amplifier to the
(+) terminal on the SUB-TS18 subwoofer, and
the (–) terminal on the receiver/amplifier to the
(–) terminal on the SUB-TS18 subwoofer.
‚ Master Power Switch: Place this
switch in the “•” position to power-on the
SUB-TS18 subwoofer. The SUB-TS18 will
then be either in the Standby mode or completely on, depending on the position of the
Audio-Sense On/Off Switch ¢.
⁄ AC Power Cord: Make sure to plug this
cord into an active, unswitched electrical outlet for proper operation of the SUB-TS18.
The cord should not be plugged into the
accessory outlets found on some audio
components.
HKTS 18 OM
10/6/06
1:34 PM
Page 10
harman/kardon
SUB-TS18
SPEAKER CONNECTIONS
Dolby® Digital or DTS® (or Other
Digital Surround Mode) Connection
USE THIS INSTALLATION METHOD FOR
DOLBY DIGITAL, DTS OR OTHER DIGITAL
SURROUND PROCESSORS:
Center
–
+
Front
Left
–
+
Front
Right
–
+
SUB-TS18 Subwoofer
Use the line-level input jack marked SUB
§ for the low-frequency effects channel.
Connect this jack to the subwoofer output
or LFE output on your receiver or amplifier.
Connect each speaker to the corresponding
speaker terminals on your receiver or
amplifier.
LINE LEVEL IN
SUB
Make sure you’ve configured your surround
sound processor for “Subwoofer On.” The
front left, front right, center and surround
speakers should all be set to “Small.”
R
Front
Left
L
Front
Right
SUB/LFE
Out
When all connections have been made, plug
the AC power cord on the subwoofer into
an AC outlet.
Surround
Left
Surround
Left
–
+
Center
Receiver
7
Surround
Right
Surround
Right
–
+
HKTS 18 OM
10/6/06
1:34 PM
Page 11
harman/kardon
SUB-TS18
SPEAKER CONNECTIONS
Dolby Pro Logic®
(Non-Digital) – Line Level
USE THIS INSTALLATION METHOD FOR
DOLBY PRO LOGIC APPLICATIONS (NOT
DOLBY DIGITAL, DTS OR OTHER DIGITAL
PROCESSING), WHERE THE RECEIVER/
PROCESSOR IS EQUIPPED WITH A
SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL
OUTPUT:
Center
Front
Left
–
–
+
–
+
SUB-TS18
Subwoofer
Line-Level
R
Use the supplied RCA-type interconnect
cable to connect the line-level subwoofer
output on your receiver or amplifier to either
the left or right Line-Level Full-Range
Input ¶ on the SUB-TS18 subwoofer.
Use both the left and right inputs on the
subwoofer if your receiver or processor has
both left and right line-level outputs. In that
case, you will need to supply a second
interconnect cable.
If your receiver is equipped with line-level outputs but does not have a separate subwoofer
output, use a Y-adapter (not supplied) to
bridge the receiver’s preamp output to the
main amp input for that channel, and connect
the long end of the adapter to the corresponding line-level input on the SUB-TS18.
Front
Right
+
L
Front
Left
Front
Right
SUB/LFE
Out
Surround
Left
Surround
Left
–
+
Center
Receiver
Surround
Right
Surround
Right
–
+
IMPORTANT: Do not use the SUB Input
§ on the subwoofer with Dolby Pro Logic
processors.
If your receiver/processor has a built-in lowpass-crossover filter for the subwoofer output, you may use the SUB Input § to
bypass the subwoofer’s internal crossover.
Connect each speaker to the corresponding
speaker terminals on your receiver or amplifier.
Make sure that you have configured your
surround sound processor for “Subwoofer
On.” The front left, front right, center and
surround speakers should all be set to
“Small.”
When all connections have been made, plug
the AC power cord on the subwoofer into
an AC outlet.
8
SPEAKER CONNECTIONS
11
HKTS 18 OM
10/6/06
1:34 PM
Page 12
harman/kardon
SUB-TS18
SPEAKER CONNECTIONS
Dolby Pro Logic
(Non-Digital) – Speaker Level
USE THIS INSTALLATION METHOD FOR
DOLBY PRO LOGIC APPLICATIONS (NOT
DOLBY DIGITAL, DTS OR OTHER DIGITAL
PROCESSING), WHERE THE RECEIVER/
PROCESSOR DOES NOT HAVE A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL
OUTPUT:
Front
Left
–
Center
–
+
+
–
Front
Right
+
SUB-TS18
Subwoofer
Connect your receiver or amplifier’s front
left and right speaker terminals to the left
and right Speaker-Level Input ª terminals on the SUB-TS18 subwoofer that are
marked “High Level In.” Connect the left and
right Speaker-Level Output • terminals
on the SUB-TS18 subwoofer that are
marked “High Level Out” to the corresponding terminals on the back of your front left
and right speakers.
H
I
G
H
L
E
V
E
L
Connect your receiver or amplifier’s center
and surround left and right speaker terminals to the corresponding terminals on the
back of your center and surround left and
right speakers.
L
R
Receiver
Front Left
When all connections have been made,
plug the AC power cord on the subwoofer
into an AC outlet.
Surround Left
Front Right
Surround Right
Surround
Right
Surround
Left
–
Center
+
–
9
+
HKTS 18 OM
10/6/06
1:34 PM
Page 13
harman/kardon
SUB-TS18
OPERATION
Move the Master Power Switch ‚
(marked Power) to the “•” (On) position.
The SUB-TS18 subwoofer will automatically
turn itself on or go into Standby mode,
depending on whether or not a signal is
being sent to it by your receiver or surround
processor, and provided that the AudioSense On/Off Switch ¢ is moved down
so that it is in the AUTO position.
When your receiver or amplifier is off, or is
not sending program material to the subwoofer, the subwoofer will be in Standby
mode and the LED indicator on the top
of the subwoofer will turn amber. When the
subwoofer senses an audio signal, it will automatically turn itself on and the LED indicator
will turn blue. If the subwoofer does not
sense a signal after approximately 20 minutes,
it will automatically go into Standby mode.
Volume
Additional Bass Adjustments
Volume can be adjusted using the Subwoofer-Level Control ¡, as shown.
Turn the control knob clockwise to
increase the volume of the subwoofer,
and counterclockwise to decrease the
subwoofer’s volume.
In addition to the volume adjustments described
previously, the SUB-TS18 subwoofer includes
a Phase Switch ∞ and a Filter Switch
™ that can be used to adjust the bass
response to suit your listening environment
or taste.
In most situations, the Phase Switch ∞
should be left in the NORMAL position.
If you suspect that the subwoofer is playing
out of phase with the other speakers, which
would tend to diminish bass response, try
placing this switch in the REVERSE
position. There is no harm in experimenting,
and you may return the switch to the
NORMAL position at any time. If you
rearrange your room and reposition the
speakers, it would be a good idea to check
whether they are in phase by flipping this
switch.
Subwoofer
Level
MIN
MAX
Subwoofer
Level
MIN
MAX
When the Audio-Sense On/Off Switch ¢
is switched to the ON position, the subwoofer will remain on, whether or not program material is playing, and the LED indicator will remain lit blue.
The High-Cut (Low-Pass) Filter Switch
™ limits the frequencies of the audio signal
inputted to the subwoofer to the low frequencies that the subwoofer reproduces
best. This allows the subwoofer to perform
more efficiently, and with superior bass
reproduction, minimizing distortion that might
occur if the subwoofer attempted to reproduce higher frequencies. This switch should
be left in the ON position, except:
If your receiver, processor or amplifier is
equipped with a compatible trigger output,
you may connect it to the SUB-TS18’s
External Trigger Input £. When you turn
on your component, if you have set it up correctly, it will send an electrical trigger signal
to the SUB-TS18, which will cause the
subwoofer to turn itself on, even when the
Audio-Sense On/Off Switch ¢ has been
placed in the AUTO position and no audio
signal is detected.
1. When the SUB Input § is being used,
in which case it has no effect, or
2. When the Speaker-Level Inputs ª
or the Line-Level Full-Range Inputs
¶ are being used with a crossover or
filter aboard the receiver or processor.
The trigger signal must be between 3 and 30
volts, although it may be an AC or DC signal,
and an AC signal may be 50Hz or 60Hz.
In these two circumstances, place the switch
in the OFF position.
If you’ll be away from home for an extended
period of time, or if the subwoofer will not be
used, switch the Master Power Switch ‚
to the OFF position.
10
OPERATION
13
harman/kardon
SUB-TS18
Test Set Up and Procedure
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
Initial Control Settings:
• Power Switch OFF; Filter OFF
• Level MIN (Full CCW)
• Phase, Auto/On switches do not matter
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single, purple SUB input.
2) Turn on generator; adjust to 60mV, 50 Hz.
3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX)
4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be
heard and felt from port tube opening.
5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be
connected to an integrated amplifier fed by the signal generator.
7) Turn on generator and adjust so that speaker level input at the amplifier is 1.2V, 50 Hz. Turn LEVEL control
full clockwise.
8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from
the port tube opening.
Sweep Function
1) Follow steps 6-8 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 2.8 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
11
harman/kardon
SUB-TS18
12
harman/kardon
SUB-TS18
13
harman/kardon
SUB-TS18
14
harman/kardon
SUB-TS18
SUB-TS18 (UL) AMP
Troubleshooting Flow Chart
AMP no signal out
no
yes
Check Fuse,Transformer,
D501, etc
Dc voltage check ±Vcc
yes
yes
no
Check Q501.Q502.Q503,D502 etc
Check+/-15VDC
yes
yes
LED red
LED light green or red
LED light green
Check,Q206,Q207,U203 etc
yes
yes
no
Check U202 pin8 signal
yes
Check U201
pin1 signal
yes
CheckU201,U202,VR201
etc
no
no
Check limiter Circuit C317
yes
Check U301,R343,R344 ,
C340,Q301,Q302, etc
yes
Check ,+VCC& -VCC
no DC voltage
Test R147 signal
yes
yes
Check RY101,D110,Q112,Q113 etc
Check CLASS 150W
MODEL
yes
no
Check Q107,Q108,Q109 etc
Check TH1
yes
yes
Check M100 signal
The Amp ass’Y OK, END
15
harman/kardon
SUB-TS18
16
harman/kardon
SUB-TS18
17
harman/kardon
SUB-TS18
18
harman/kardon
SUB-TS18
19
harman/kardon
SUB-TS18
SUB-TS18 120V Electrical parts list
Part number
Description
Qty Reference Designator
PREAMP PCB
Resistors
110-12472j52-e
110-16102j26-e
RESISTOR4.7K 1/2W ±5% CF 52mm (RoHS)
RESISTOR 1K 1/6W ±5% CF 26mm (RoHS)
2
6
110-16103j26-e
RESISTOR 10K 1/6W ±5% CF 26mm (RoHS)
18
110-16104j26-e
110-16105j26-e
110-16113j26-e
110-16122j26-e
110-16134j26-e
110-16152j26-e
110-16183j26-e
110-16203j26-e
110-16223j26-e
110-16303j26-e
110-16472j26-e
110-16473j26-e
110-16474j26-e
110-16475j26-e
110-16512j26-e
110-16622j26-e
110-16684j26-e
110-16912j26-e
110-16913j26-e
116-169091f26-e
RESISTOR 100K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 1M 1/6W ±5% CF 26mm (RoHS)
RESISTOR 11K 1/6W ±5% 26mm (RoHS)
RESISTOR 1.2K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 130K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 1.5K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 18K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 20K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 22K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 30K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 47K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 470K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 4.7M 1/6W ±5% CF 26mm (RoHS)
RESISTOR 5.1K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 6.2K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 680K 1/6W CF 26mm (RoHS)
RESISTOR 9.1K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 91K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 9.09K 1/6W±1% MF 26mm (RoHS)
variable RESISTOR RV16AE-20B2-15K-A54-104(A50K)
(RoHS)
metal oxide film RESISTOR 1K 2W ±5% 5mm (RoHS)
5
1
1
1
1
1
1
2
6
2
3
2
1
1
2
1
1
2
4
1
R201,R202
R213,R214,R215,R254,R253,R304
R209,R212,R216,R217,R218,R220,R221,R222,R225,R
228,R229,R230,R232,R235,R240,R248,R260,R270
R231,R263,R266,R257,R300
R259
R268
R265
R233
R302
R262
R237,R238
R247,R255,R256,R249,R250,R261
R223,R224
R200,R207,R258
R219,R264
R251
R303
R210,R211
R234
R252
R226,R227
R203,R204,R205,R206
R301
1
VR201
1
R267
129-a154j633-e
129-a224j633-e
130-2b103k503-e
METALIZE CAP. 0.15U 63V ±5% MSC (RoHS)
METALIZE CAP. 0.22uF 63V ±5% MSC (RoHS)
DISC CAPACITOR 0.01u 50V ±10% (RoHS)
2
1
1
130-2b221k503-e
DISC CAPACITOR 220P 50V ±10% (RoHS)
12
130-3f104z503-e
132-183j503-e
132-223ja03-e
132-473j503-e
132-563j503-e
132-823j503-e
135-3105m50-e
DISC CAPACITOR 0.1U 50V +80/-20% (RoHS)
MYLAR CAPACITOR 0.018uF 50V ±5% (RoHS)
MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS)
MYLAR CAPACITOR 0.047U 50V ±5% (RoHS)
MYLAR CAPACITOR 0.056U 50V ±5% (RoHS)
MYLAR CAPACITOR 0.082U 50V ±5% (RoHS)
ELECTROLYTIC CAP. 1U 50V ±20% (RoHS)
8
1
1
1
1
1
1
135-3106m50-e
ELECTROLYTIC CAP. 10uF 50V ±20% (RoHS)
12
135-3107m16-e
135-3226m50-e
135-3475m16-e
135-3107m50-e
135-3227m50-e
ELECTROLYTIC
ELECTROLYTIC
ELECTROLYTIC
ELECTROLYTIC
ELECTROLYTIC
1
1
1
1
1
C221,C222
C218
C238
C200,C204,C205,C207,C208,C210,C211,C212,C214,C
220,C230,C237
C232,C242,C244,C245,C246,C252,C254,C256
C223
C215
C224
C216
C217
C228
C201,C202,C206,C213,C219,C231,C241,C243,C251,C
253,C248,C247
C234
C225
C233
C301
C300
115-h503a102-e
116-201001j5vx-e
Capacitors
CAP. 100uF 16V ±20% (RoHS)
CAP. 22U 50V ±20% (RoHS)
CAP.4.7U 16V ±20% (RoHS)
CAP. 100U 50V ±20% (RoHS)
CAP. 220uF 50V ±20% (RoHS)
Semiconductors
192-027c1815gr-e
TRANSISTOR 2SC1815GR NPN TOSHIBA(RoHS)
4
197-631n4148-e
DIODE 500mW 75V 1N4148 Panjit (RoHS)
13
199-65000513g-e
190-06m4558d-e
190-06m4558ld-e
190-16tl074cn-e
197-141n4004-e
190-05ps25051-e
ZENER DIODE GDZJ5.1B 500mW 5.1V 2% ROHM 1N5231B
I.C. OPA 4558D dual OP-AMP inline (RoHS)
I.C. NJRC NJM4558LD OP-AMP inglerow inline (RoHS)
I.C TL074CN ST QUAD OP-AMP
*DIODE 1N4004 shaping short crus (RoHS)
photoelectric coupler PS2505-1 NEC (RoHS)
1
1
1
2
4
1
20
Q201,Q206,Q207,Q208
D201,D202,D203,D204,D205,D206,D207,D208,D214,D
215,D216,D301,D302
D213
U203
U204
U201,U202
D217,D218,D219,D220
U1
harman/kardon
SUB-TS18
Part number
Description
Qty Reference Designator
PREAMP PCB
Miscellaneous
162-50122004-e
162-5014d008-e
162-a016d001-e
174-0rca313v-e
174-20810360g-e
174-6ej3556agp-e
175-1b08v01-e
175-1c07v01-e
180-tms7210v-e
362-FE-00041-0LAE
drop-out line 120mm RED/WHT 2PIN (RoHS)
WIRE 2468#26AWG RED/WHT length 140mm (RoHS)
mixed wire UL1007 160/80mm#26 (RoHS)
RCA JACK RCA-313G V/R/W (RoHS)
jack SPK JK BP 8PIN (RoHS) SH0810360G US1.35
PHONE JACK EJ3556A-GP (RoHS)
WIRE CONNECTOR & BASE 8 PIN PITCH=2.0mm(RoHS)
WIRE CONNECTOR & BASE 7PIN PITCH=2.5mm (RoHS)
SWITCH SLIDE 6PIN MS7210V (RoHS)
PCB support 11.75*8.5*12.5H (RoHS)
1
1
1
1
1
1
1
1
3
2
D209
P1-P2
W202
JK201
JK202
JK203
W202
M201
SW201,SW202,SW203
110-14103j26-e
110-14222j26-e
110-14432j26-e
110-14472j26-e
110-16102j26-e
RESISTOR 10K 1/4W ±5% CF 26mm (RoHS)
RESISTOR 2.2K 1/4W ±5% CF 26mm (RoHS)
RESISTOR 4.3K 1/4W ±5% CF 26mm (RoHS)
RESISTOR 4.7K 1/4W ±5% CF 26mm (RoHS)
RESISTOR 1K 1/6W ±5% CF 26mm (RoHS)
3
1
1
1
1
110-16103j26-e
RESISTOR 10K 1/6W ±5% CF 26mm (RoHS)
10
110-16104j26-e
110-16153j26-e
110-16182j26-e
110-16203j26-e
110-16221j26-e
110-16222j26-e
110-16223j26-e
110-16333j26-e
110-16393j26-e
110-16434j26-e
110-16473j26-e
110-16474j26-e
110-16562j26-e
110-16621j26-e
110-16751j26-e
110-16755j26-e
116-161002f26-e
116-161202f26-e
116-162200f26-e
116-162202f26-e
110-20332jk3-e
113-50s68j00-e
116-201001jk3x-e
116-304700jk2x-e
RESISTOR 100K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 15K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 1.8K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 20K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 220Ω 1/6W ±5% CF 26mm (RoHS)
RESISTOR 2.2K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 22K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 33K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 39K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 430K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 47K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 470K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 5.6K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 620Ω 1/6W ±5% CF 26mm (RoHS)
RESISTOR 750Ω 1/6W ±5% CF 26mm (RoHS)
RESISTOR 7.5M 1/6W ±5% CF 26mm (RoHS)
metal film RESISTOR 10K 1/6W ±1% MF 26mm (RoHS)
metal film RESISTOR 12.0K 1/6W ±1% MF 26mm (RoHS)
metal film RESISTOR 220Ω 1/6W ±1% MF 26mm (RoHS)
metal film RESISTOR 22.0K 1/6W ±1% MF 26mm (RoHS)
RESISTOR 3.3K 2W ±5% standing short crus 7.5m (RoHS)
cement RESISTOR 0.068Ω 5W ±5% prone long crus (RoHS)
oxide film RESISTOR 1.00K 2W ±5% 7.5mm (RoHS)
oxide film RESISTOR 470Ω 3W ±5% 10mm (RoHS)
3
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
2
R503,R504,R510
R511
R506
R505
R153
R128,R130,R149,R150,R305,R306,R308,R311,R314,R
319
R122,R126,R307
R107
R145
R309
R144
R102
R316
R310
R151
R312
R106,R129
R127
R152
R160
R315
R313
R301,R303
R302
R317
R318
R134
R147
R148
R501,R502
DISC CAPACITOR 0.1U 50V +80/-20% (RoHS)
DISC CAPACITOR 100P 50V SL ±10% (RoHS)
MYLAR CAPACITOR 0.01uF 50V ±5% (RoHS)
MYLAR CAPACITOR 0.01uf 100V ±5% (RoHS)
MYLAR CAPACITOR 0.1UF 100V ±5% (RoHS)
MYLAR CAPACITOR 0.027UF 100V ±5% (RoHS)
ELECTROLYTIC CAP. 10uF 50V ±20% (RoHS)
ELECTROLYTIC CAP. 100U 10V ±20% (RoHS)
ELECTROLYTIC CAP. 100U 35V ±20% (RoHS)
ELECTROLYTIC CAP. 2.2U 50V ±20% (RoHS)
ELECTROLYTIC CAP. 22U 16V ±20% (RoHS)
ELECTROLYTIC CAP. 22U 50V ±20% (RoHS)
ELECTROLYTIC CAP. 220U 16V ±20% (RoHS)
ELECTROLYTIC CAP. 47U 16V ±20% (RoHS)
6
3
2
2
3
1
2
2
2
1
1
2
1
1
C107,C117,C122,C144,C320,C322
C302,C303,C306
C305,C317
C103,C104
C123,C503,C504
C143
C319,C321
C114,C115
C507,C508
C509
C304
C505,C506
C118
C318
MAIN PCB
Resistors
Capacitors
130-3f104z503-e
130-sl101k503-e
132-103j503-e
132-103ja03-e
132-104ja03-e
132-273ja03-e
135-3106m50-e
135-3107m10-e
135-3107m35-e
135-3225m50-e
135-3226m16-e
135-3226m50-e
135-3227m16-e
135-3476m16-e
21
harman/kardon
SUB-TS18
Part number
Description
Qty Reference Designator
MAIN PCB
138-5478m80-e
LARGE ELECTROLYTIC CAP. 4700uF 80V ±20% 85 ℃
2
C501,C502
132-103kd00-e
MYLAR CAPACITOR 0.01U 400V +/-10% long crus (RoHS)
1
C500
TRANSISTOR 2SC1815GR NPN TOSHIBA(RoHS)
TRANSISTOR 2SC2235Y NPN TOSHIBA (RoHS)
TRANSISTOR 2SA1015GR PNP TOSHIBA(RoHS)
*TRANSISTOR FSC 2N5551 NPN (RoHS)
TRANSISTOR FSC 2N5401 AI-PNP 350V 500mA TO-92
(RoHS)
DIODE 500mW 75V 1N4148 Panjit (RoHS)
ZENER DIODE GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS)
ZENER DIODE GDZJ16C 500mW 16V 26mm 2% (RoHS)
I.C TL074CN ST QUAD OP-AMP
TRANSISTOR TIP31C NPN SGS (RoHS)
TRANSISTOR TIP32C PNP SGS (RoHS)
bridge rectifier 6A 800V KBU606G (RoHS)
*DIODE 1N4004 shaping short crus (RoHS)
5
1
3
2
Q108,Q109,Q113,Q301,Q302
Q111
Q101,Q107,Q112
Q114,Q115
1
Q503
7
1
1
1
1
1
1
2
D102,D103,D104,D105,D143,D301,D302
D101
D502
U301
Q501
Q502
D501
D110,D504
thermistor TTC-802(JS) NTC long crus (RoHS)
inductor 10W AI YT-C3104-005 1CRHW 354708LTB (RoHS)
CABLE ASS'Y drop-out line 120mm AWG28 WHT (RoHS)
relay RWH-SH-124D (1600 ohm) (RoHS)
WIRE CONNECTOR & BASE 2PIN PITCH=3.96mm (RoHS)
WIRE CONNECTOR & BASE 3 PIN PITCH=3.96mm JST-VH
take off the middle PIN
1
2
1
1
1
TH1
FB1,FB2
W201
RL1
M100
1
M500
Semiconductors
192-027c1815gr-e
192-027c2235y-e
192-028a1015gr-e
192-1572n5551-e
192-1582n5401-e
197-631n4148-e
199-65000623g-e
199-65001603g-e
190-16tl074cn-e
192-161tip31c-e
192-162tip32c-e
197-00kbu606g-e
197-141n4004-e
Miscellaneous
109-1ttc802j0-e
120-1000003-e
162-50129001-e
171-urwh124d-e
175-1d02v01-e
175-1d03v01-e
CLASS D ASS'Y PCB (Replacment of entire module is recommended, part# 051-B00012A-E).
Resistors
118-12061001j-e
118-12061002j-e
118-120610r0j-e
SMD RESISTOR 1.00K 1206 5% (RoHS)
SMD RESISTOR 10.0K 1206 5% (RoHS)
SMD RESISTOR 10.0Ω 1206 5% (RoHS)
4
3
2
118-12061201j-e
SMD RESISTOR 1.20K 1206 5% (RoHS)
16
118-12062002j-e
118-12062201j-e
118-12062701j-e
118-12063000j-e
118-12063301j-e
118-12063902j-e
118-12064700j-e
118-12064701j-e
118-12064702j-e
118-12064704j-e
118-120647r0j-e
SMD RESISTOR 20.0K 1206 5% (RoHS)
SMD RESISTOR 2.20K 1206 5% (RoHS)
SMD RESISTOR 2.70K 1206 5% (RoHS)
SMD RESISTOR 300.0Ω 1206 5% (RoHS)
SMD RESISTOR 3.30K 1206 5% (RoHS)
SMD RESISTOR 39.0K 1206 5% (RoHS)
SMD RESISTOR 470Ω 1206 5% (RoHS)
SMD RESISTOR 4.70K 1206 5% (RoHS)
SMD RESISTOR 47.0K 1206 5% (RoHS)
SMD RESISTOR 4.70M 1206 5% (RoHS)
SMD RESISTOR 47.0Ω 1206 5% (RoHS)
1
3
1
1
4
1
1
3
1
1
2
R2,R11,R29,R30
R7,R9,R25
R22,R23
R31,R32,R33,R34,R35,R36,R37,R38,R39,R40,R41,
R42,R43,R44,R45,R46
R26
R6,R13,R16
R10
R24
R14,R15,R27,R28
R3
R8
R1,R5,R12
R17
R4
R20,R21
SMD CAPACITOR 100pF 50V 10% 1206 NP0 (RoHS)
SMD CAPACITOR 22pF 50V 10% 1206 SMT NPO (RoHS)
SMD CAPACITOR 560pF 50V 10% 1206 NPO (RoHS)
SMD CAPACITOR 1206 Y5V 0.1uF 50V ±20% (RoHS)
SMD CAPACITOR 0.022uF 50V 10% 1206 X7R (RoHS)
SMD CAPACITOR 0.1uF 100V 10% 1210 X7R (RoHS)
SMD CAPACITOR 0.1uF 250V 10% 1210 X7R (RoHS)
1
1
1
8
1
1
5
C4
C5
C6
C2,C3,C7,C8,C9,C10,C11,C15
C13
C12
C1,C18,C19,C20,C14
*SMD I.C. TL072CDT Dual Op-Amp SGS THOMSON (RoHS)
SMD TRANSISTOR 2SC2412K-T146Q/R ROHM (RoHS)
1
3
IC1
Q1,Q4,Q5
Capacitors
141-c0101k50-e
141-c0220k50-e
141-c0561k50-e
141-c5104m50-e
141-c7223k50-e
141-d7104ka0-e
141-d7104kb5-e
Semiconductors
190-16tl072dts-e
192-09124126qs-e
22
harman/kardon
SUB-TS18
Part number
Description
Qty Reference Designator
CLASS D ASS'Y PCB
192-09139066rs-e
192-09210376qs-e
192-09215146rs-e
197-03rls4148s-e
199-15000563s-e
199-1500120s-e
199-15001503s-e
192-233f640n-e
192-232irf9640-e
SMD TRANSISTOR 2SC3906K-T146R ROHM (RoHS)
SMD TRANSISTOR 2SA1037K-T146Q/R ROHM (RoHS)
SMD TRANSISTOR 2SA1514K-T146R ROHM (RoHS)
*SMD DIODE RLS4148-TE11 ROHM (RoHS)
SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 (RoHS)
SMD ZENER 12V 5% PHILIPS BZX84-C12 (RoHS)
SMD ZENER 15V 5% PHILIPS BZX84-C15 (RoHS)
TRANSISTOR IRF640N INTERNATIONAL (RoHS)
FET IRF9640 IR P-CH TO220 (RoHS)
2
2
2
6
2
2
2
1
1
Q2,Q8
Q7,Q9
Q3,Q6
D1,D2,D3,D4,D5,D6
Z1,Z2
Z5,Z6
Z3,Z4
Q11
Q10
choke coil 35uH Ferrite Core 25 Milliohm (RoHS)
non polarized ELEC LYTIC CAP. 10UF 100V 20% 105 ℃
(RoHS)
WIRE CONNECTOR & BASE 40PIN PITCH=2.54mm HR2*40
(RoHS)
Ferrite core 日word type LS-A6206-ST EFD-30 (RoHS)
1
L2
2
C16,C17
1
L1
1
1
1
1
1
1
1
1
1
2
1
T501
Miscellaneous
122-14350j4180-e
128-e106ma01k-e
175-9f40hr2-e
122-14121m4191-e
MISCELLANEOUS/MECHANICAL
150-r4055903-e
152-u602015-e
154-k31505t0-e
155-63032i-e
162-10152001-e
162-5020d006-e
162-50552003-e
176-wjce1-e
180-prf1003s-e
193-201815t2-e
302-AL-00373-1BGE
306-ABS-00714-0BAE
311-ABS-00028-0BAE
317-000-00037-0LAE
323-AL-00056-0LAE
333-EVA-00096-0BAE
333-EVA-00097-0BAE
333-EVA-00121-0BAE
333-EVA-00132-0BAE
333-EVA-00133-0BAE
333-EVA-00188-0BAE
333-EVA-00219-0BAE
333-EVA-00220-0BAE
333-EVA-00866-0BAE
335-NYL-00002-0BAE
335-NYL-05015-0BAE
350-EM04012D024-E
351-AM03008A078-E
351-AM03008A079-E
352-AM03008D040-E
352-AM03008D041-E
352-AM03010D065-E
352-HM03012D086-E
353-0870122-E
362-FE-00013-0LAE
Power transformer TT0900304490 (RoHS)
power cord joint heteropolarity SVT FT-26FT bi-insul (RoHS)
fuse 3.15A 250V 30mm UL/CSA/PSE (RoHS)
fuse holder HTB-32I 30mm UL/CSA (RoHS)
WIRE UL1617 AWG22 150mm RED 6:6 (RoHS)
WIRE UL2468 200mm 2.5mmpitch RED/WHT (RoHS)
WIRE UL1007 #16 550mm (RoHS) #110/#205 0.5T
dead end CE-1 (RoHS)
power switch ROCK RF-1003-BB2-OHA(RoHS)
ceramic insulator (RoHS)
aluminium rear board 270*215*2.5T anode black (RoHS)
plastic rear housing 268*213*102 spout conductive paint
(RoHS)
plastic KNOB 46077-W soft material P.V.C.(RoHS) LEVEL
earth terminal M3 lug plate t=0.3 (RoHS)
heat sink 83.5*50.5*27.5H defat
Gasket pad wide sides 213*15*2.0mm (RoHS)
Gasket pad wide sides 213*15*1.0t (RoHS)
8PIN BB Gasket (RoHS)
Gasket pad long sides 238*15*2.0mm (RoHS)
Gasket pad long sides 238*15*1.0t (RoHS)
Gasket pad 170x5x1t glue on back (RoHS)
Gasket pad wide sides 150*15*1t UL (RoHS)
Gasket pad long sides 225*15*1t UL (RoHS)
Gasket 48*18*1.5T (RoHS)
WIRE CLIP 4K-4 NO-BB(RoHS)
power cord fixed button SB4F-2 黑色(RoHS)
4*12 wood screw electrical back (RoHS)
M3*8 machine screw nickel plating (RoHS)
M3*8 machine screw electrical back (RoHS)
3*8 type ping screw electrical back (RoHS)
3*8 type ping screw nickel plating (RoHS)
3*10 P type ping electrical back (RoHS)
3*12 type ping screw electrical back (RoHS)
machine screw M8*70 round head electrical back (RoHS)
PCB support L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS)
23
1
1
1
1
2
2
1
2
2
1
2
1
1
1
1
4
4
4
2
2
3
1
1
2
F501
SW501
for Q10,Q11
harman/kardon
SUB-TS18
24
harman/kardon
SUB-TS18
25
harman/kardon
SUB-TS18
26
harman/kardon
SUB-TS18
27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement