A.O. Smith Custom Commercial Solar Water Heating Systems Technical Documents

A.O. Smith Custom Commercial Solar Water Heating Systems Technical Documents
AOSCE16000 Solar Storage Tank Spec Sheet:AOS Effex Res HE Spec Sheet
9/18/11
2:47 PM
Page 1
Solar Commercial Storage Tanks
FACTORY JACKETED AND INSULATED SOLAR
COMMERCIAL STORAGE TANKS
Large volume solar storage tanks from A. O. Smith are designed for storing
potable water. These storage tanks are fitted with additional openings to
suit the specific needs of solar thermal, commercial heat pump, and other
renewable energy heat sources.
SJV-140 thru 2000
and
SJH-200 thru 1000
These tanks are available as pre-configured Specialty Solar Tanks and as
Custom Solar Tanks built to specified application requirements. See the
Custom Solar Tank options on page 4 and consult your
factory representative for more information.
FEATURES
SPECIALTY SOLAR TANKS: Vertical tanks from 140 to 2,000 gallons,
horizontal tanks from 200 to 1,000 gallons. A. O. Smith commercial
solar storage tanks are constructed with openings for potable water
and solar thermal/renewable energy applications as shown in the
drawings that follow. These heavy duty storage tanks have been
designed for new construction and retrofit applications.
ASME CONSTRUCTION
I All tanks are ASME constructed at 160 psi working pressure.
Consult your factory representative for tanks with greater or
lesser working pressures
GLASSLINED
I Specialty Solar Tanks feature A. O. Smith PermaGlas® coating that
provides superior protection against corrosion and is fused to all
inner tank surfaces at 1600°F
INSULATION
I All tanks are surrounded with 3 inches of high density fiberglass insulation to reduce
costly heat loss; insulation is non-sagging and verminproof. To meet ASHRAE 90.1 (current
edition) depth of insulation cavity requires use of remote bulb-type tank temperature control
and thermometer. Storage tanks meet R12.5 minimum thermal insulation requirements of the
U.S. Department of Energy and current edition of ASHRAE/IESNA 90.1
JACKET/CABINET
I All tanks feature heavy gauge steel with high quality powder coat paint that provides
additional insulating qualities for greater energy savings
CATHODIC PROTECTION
I All tanks are furnished with factory installed magnesium anodes designed for
maximum protection
CONNECTIONS
I Tanks will be supplied with the fittings located as indicated on the drawings unless specified
otherwise. Manhole or handholes are optional on glasslined tanks but are included on
cement lined tanks
TEMPERATURE SENSORS
I Factory installed upper and lower temperature sensor wells with Pt1000 type sensors and
internal wiring pre-installed.
U
ASME
OPTIONAL
CRN
These storage tanks are
eligible for a 30% federal tax
credit when installed as part of
a complete commercial solar
thermal hot water system.
CUSTOM SOLAR TANKS: See options and suggested specification on page 4.
Page 1 of 4
AOSCE16000
AOSCE16000 Solar Storage Tank Spec Sheet:AOS Effex Res HE Spec Sheet
9/18/11
2:47 PM
Page 2
Solar Commercial Storage Tanks
VERTICAL STORAGE TANKS
J SENSOR WELL
A
A
LIFTING LUGS
T&P VALVE
K
OPENING
ANODE
HOT OUTLET H
SENSOR WELL J
JACKET (CABINET)
FRONT VIEW
SIDE VIEW
TOP VIEW
3" INSULATION
FOR SHIPPING
ONLY
I SOLAR RETURN
B
SENSOR WIRING
J
SENSOR WELL
ANODE
F
H COLD INLET
E D
I SOLAR DRAW
C
DRAIN G
(MALE NPT)
DRAWING NOTES:
I Inspection openings, IE: handholes and manholes, are optional with glasslined or stainless steel tanks and will only be included when specified. Tanks so
equipped are FOB Seattle.
I All openings female pipe thread except as noted.
I Number of factory installed anode rods will vary with tank size.
SJV-140 THROUGH SJV-2000
SOLAR
DRAW
HEIGHT
LOWER
SENSOR
HEIGHT
COLD
INLET
HEIGHT
SOLAR
RETURN
HEIGHT
DRAIN
(IN. NPT)
INLET/OUTLET
CONNECTIONS
(IN. NPT)
GLASSLINED
DRY WEIGHT
(LBS.)
WIDTH
MODEL
NOMINAL
VOLUME
(GALLONS)
A
B
C
D
E
F
G
H
SJV-140
SJV-200
SJV-250
SJV-300T
SJV-300S
SJV-350
SJV-400
SJV-450
SJV-500T
SJV-500S
SJV-600
SJV-700
SJV-800
SJV-900
SJV-1000T
SJV-1000S
SJV-1500
SJV-2000T
SJV-2000S
140
200
250
300
300
350
400
450
500
500
600
700
800
900
1000
1000
1500
2000
2000
613
749
811
898
857
942
1436
1565
1682
1714
1820
1911
2974
3208
3697
3947
4456
6035
5952
30
36
36
36
42
42
42
42
42
48
48
48
54
54
54
**66
**60
**66
**78
86
82
95
110
82
97
104
118
133
99
114
130
120
128
148
99
164
176
131
13
14
14
14
15 1/2
15 1/2
15 1/2
15 1/2
15 1/2
17
17
17
18
18
18
21
19 1/2
21
24
18 1/2
20
20
20
21 1/2
21 1/2
21 1/2
21 1/2
21 1/2
23
23
23
24 1/2
24 1/2
24 1/2
27 1/2
26
27 1/2
30 1/2
19
20
20
20
22
22
22
22
22
23 1/2
23 1/2
23 1/2
25
25
25
28
26 1/2
28
31
49 1/2
48
54
62
48
56
59
66 1/2
74
57
65
73
68
72
82
58
90 1/2
97
75
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
3
3
3
3
3
3
3
3
3
3
HEIGHT
SOLAR LOOP
CONNECTIONS
(IN. NPT)
*SENSOR
WELLS
(IN. NPT)
T&P VALVE
OPENING
(IN. NPT)
I
J
K
1 1/2
1 1/2
1 1/2
1 1/2
2
1 1/2
2
2
2
2 1/2
2
2
2 1/2
2 1/2
2 1/2
3
3
3
3
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
All dimensions are in inches.
Four vertical tanks are available in short and tall models. The S and T designators at the end of the model numbers are used to identify these models.
* Sensor well openings are 1/2" NPT female. All models have factory installed Pt1000 temperature sensors and wiring to an external junction box. Access covers are provided for field
supplied temperature sensors and servicing.
** These models will have rectangular jackets when manufactured for indoor use. All other models will have round jackets.
A. O. Smith Corporation reserves the right to make product changes or improvements without prior notice.
Page 2 of 4
www.hotwater.com
AOSCE16000
AOSCE16000 Solar Storage Tank Spec Sheet:AOS Effex Res HE Spec Sheet
9/18/11
2:47 PM
Page 3
Solar Commercial Storage Tanks
HORIZONTAL STORAGE TANKS
L
SENSOR WELL
J
D
M
T&P VALVE
OPENING
B
HOT OUTLET
CABINET
SENSOR WIRING
3" INSULATION
FRONT VIEW
ANODE
COLD INLET
SIDE VIEW
ANODE
K
SOLAR RETURN
L
SENSOR
WELL
K
SOLAR DRAW
(MALE NPT)
A
J
F
E
G
DRAIN
(MALE NPT)
H
I
H
C
DRAWING NOTES:
I Inspection openings, IE: handholes and manholes, are optional with glasslined or stainless steel tanks and will only be included when specified. Tanks so
equipped are FOB Seattle
I All openings female pipe thread except as noted
I Number of factory installed anode rods will vary with tank size
SJH-200 THROUGH SJH-1000
HOT
OUTLET
CENTER
SOLAR
DRAW
HEIGHT
E
F
G
H
I
J
K
L
M
13
23
4
16
1 1/2
2 1/2
1 1/2
1/2
1
13
23
4
22 1/2
1 1/2
2 1/2
1 1/2
1/2
1
17 1/2
12
26
4
22 1/2
1 1/2
2 1/2
1 1/2
1/2
1
99
17 1/2
12
26
4
26
1 1/2
2 1/2
2
1/2
1
54
79
23
14
32
4
11
1 1/2
3
2
1/2
1
59
54
111
23
14
32
4 1/2
27
1 1/2
3
2 1/2
1/2
1
59
54
143
23
13
32
5
43
1 1/2
3
3
1/2
1 1/2
MODEL
GLASSLINED
DRY
WEIGHT
(LBS.)
A
B
C
D
SJH-200
200
1020
41
36
77
16
SJH-250
250
1082
41
36
90
16
SJH-350
350
1232
47
42
93
SJH-400
400
1402
47
42
SJH-500
500
2270
59
SJH-750
750
2970
SJH-1000
1000
3751
HEIGHT DEPTH LENGTH
COLD
INLET
HEIGHT
TANK
SADDLE
CENTERS
T&P
INLET/OUTLET SOLAR LOOP *SENSOR
VALVE
CONNECTIONS CONNECTIONS WELLS
OPENING
(IN. NPT)
(IN. NPT)
(IN. NPT)
(IN. NPT)
SOLAR
RETURN
HEIGHT
NOMINAL
VOLUME
(GALLONS)
DRAIN
(IN. NPT)
All dimensions are in inches.
* Sensor well openings are 1/2" NPT female. All models have factory installed Pt1000 temperature sensors and wiring to an external junction box. Access covers are provided for field
supplied temperature sensors and servicing.
A. O. Smith Corporation reserves the right to make product changes or improvements without prior notice.
Page 3 of 4
www.hotwater.com
AOSCE16000
AOSCE16000 Solar Storage Tank Spec Sheet:AOS Effex Res HE Spec Sheet
9/18/11
2:48 PM
Page 4
Solar Commercial Storage Tanks
CUSTOM SOLAR TANKS: Customized solar tanks with specified construction materials and configurations are also available;
consult your factory sales representative for more information.
CUSTOM OPTIONS INCLUDE:
I
I
I
I
I
I
I
I
Glasslined tanks
Cement lined tanks
Stainless steel tank construction
Specified gallon capacities up to 12,500 gallons
Specified tank dimensions
Specified tank openings
Specified tank opening locations
Outdoor models - entire tank is sprayed with minimum of 2 inch high-density polyurethane foam insulation that forms a
watertight jacket that is approved for outdoor use. Meets or exceeds the thermal efficiency and standby loss requirements
of the U.S. Department of Energy and Current Edition of the ASHRAE/IESNA 90.1
– Note: Minimum foam insulation thickness is 2 inches; however, since tank is hand sprayed, insulation thicknesses may
be greater in some areas giving the finished tank an uneven but watertight surface
I Additional insulation - provides R16 insulation value - adds 8” to tank jacket diameter/cabinet dimensions
I Supplemental/backup heat sources
– Electric heating element packages - standard voltages 208/240 VAC (single/three phase), 480 three phase. Advanced
electronic controller, modulating step control, low water cutoffs. Contact your factory sales representative for available
kW input configurations
– Tank heaters - flange mounted removable single/double wall copper tube heat exchangers for backup heating from low
pressure steam or boiler water
– Tank heaters - flange mounted removable single/double wall copper tube heat exchangers for supplemental heat from
alternate heat sources such as geo-thermal, air or water source heat pumps
LIMITED WARRANTY OUTLINES
GLASSLINED and CEMENT: If the tank should leak anytime during the first five years, under the terms of the warranty,
A. O. Smith will repair or replace the tank; installation, labor and handling extra.
NOTE: THIS OUTLINE IS NOT A WARRANTY. For complete information, consult the written warranty or A. O. Smith. Warranty does
not apply to product installed outside of the United States of America or its territorial possessions and Canada.
SAMPLE SPECIFICATION FOR CUSTOM-LINE STORAGE TANKS
When jacketed or insulated these models meet R12.5 minimum thermal insulation requirements of the U.S. Department of Energy and current edition of
ASHRAE/IESNA 90.1.
ASME storage tank to be A. O. Smith Custom-Line model ___________________. Capacity to be ___________ gallons with a diameter of _________ inches.
Tank(s) shall be constructed and stamped according to ASME specifications for __________ psi working pressure. Manhole (11 x 15), handhole (4x6) or
inspection openings (2-2˝) shall be installed in accordance with ASME code requirements and manufacturer(s) standard practice. Tank to be constructed
of (carbon steel) _________. Lining shall be (glass or cement) ______________. Tank(s) lined with (glass or cement) _____________lining shall be equipped
with the number and size of magnesium anode rod(s) sufficient to provide adequate protection for the tank lining.
Tank shall be (vertical, horizontal) _______________ design and provided with (four) ___________ (angle iron legs, threaded leg socket(s)) _____________
ring base, ___________ saddles.
Tank shall be equipped with two (one upper and one lower) factory-installed Pt1000 temperature sensors for renewable energy control devices such as
those used on solar thermal control systems. Sensor wells shall be installed in 1/2 inch female NPT openings to accommodate Pt1000 sensors. These wells
shall be removable to accommodate field supplied temperature sensing devices. Wiring for temperature sensors will be factory installed and terminate
in a junction box affixed to the outside jacket. On outdoor models this wiring shall terminate in a weather proof wiring box.
SAMPLE SPECIFICATION FOR TANK HEATERS (Tube Bundle Heat Exchangers)
Tank heaters shall be Model No. ____________ 3/4˝ OD 20 gauge copper “U” tubes. The tank heater shall be a (single, double) __________ wall heat
exchanger construction. Tank heater to have ________ square feet of heating surface to heat ____________ gallons per hour from _____________ degrees
F to ____________ degrees F with heating media of ____________ psi steam (or _________ degrees F boiler, heat pump, geothermal, or other heat source
water). The tank heater element shall be constructed so that the entire section can be removed from the tank for cleaning and inspection.
A. O. Smith Corporation reserves the right to make product changes or improvements without prior notice.
Page 4 of 4
www.hotwater.com
© 2011 A. O. Smith Corporation
AOSCE16000
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement