advertisement
V13.1.00
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer.
©June 2013
Trademarks
Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:
• Off Mode < 0.5W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1.
This device may not cause interference.
And
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
IV
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1.
This device may not cause interference.
And
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
V
Preface
FCC RF Radiation Exposure Statement:
1.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Important Notice - 3G & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3G module and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G module is powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.
VI
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1.
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2.
Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3.
Do not use the telephone to report a gas leak in the vicinity of the leak.
4.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
5.
This product is intended to be supplied by a Listed Power Unit:
• Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19.5V, 6.15A (120W) minimum.
VII
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.
Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
2.
Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on any surface that will block the
Vents/Fan Intakes.
VIII
Preface
3.
Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4.
Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all programs.
Do not turn off any peripheral devices when the computer is on.
Do not disassemble the computer by yourself.
Perform routine maintenance on your computer.
5.
Take care when using peripheral devices.
Use only approved brands of peripherals.
Unplug the power cord before attaching peripheral devices.
IX
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).
•Only use a power adapter approved for use with this computer.
•Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
•The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
•When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
•Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
•Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
You must also remove your battery in order to prevent accidentally turning the machine on. Before removing
the battery disconnect the AC/DC adapter from the computer.
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
X
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.
• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
XI
Preface
General Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
XII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
XIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.
Check that the battery pack and any spares are fully charged.
2.
Power off the computer and peripherals.
3.
Close the display panel and make sure it’s latched.
4.
Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.
The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
6.
Put the notebook in its carrying bag and secure it with the bag’s straps.
7.
If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.
8.
Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
XIV
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
•Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
•Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
•Use a chair with a back and adjust it to support your lower back comfortably.
•Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.
•Take periodic breaks if you are using the computer for long periods of time.
Remember to:
•Alter your posture frequently.
•Stretch and exercise your body several times a day.
•Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XVI
Preface
Lighting
Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.
XVII
Preface
XVIII
Preface
Contents
Quick Start Guide
XIX
Preface
XX
Preface
Storage Devices, Audio & Mouse
Power Management
XXI
Preface
Drivers & Utilities
XXII
Preface
BIOS Utilities
XXIII
Preface
Upgrading The Computer
XXIV
Preface
Modules
XXV
Preface
XXVI
Preface
Troubleshooting
Interface (Ports & Jacks)
XXVII
Preface
Control Center
Video Driver Controls
XXVIII
Preface
Specifications
XXIX
Preface
XXX
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, card reader), TouchPad & Mouse & Audio Features.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN
Combo, Intel technology, Sound Blaster Audio and 3G modules (some of which may be optional depending on your purchase configuration).
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.
• Appendix B Information on the Control Center.
• Appendix C Information on the Video driver controls.
• Appendix D The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
“Drivers & Utilities” on page 4 - 1
“BIOS Utilities” on page 5 - 1
“Upgrading The Computer” on page 6 - 1
in the User’s Manual. You may also find the notes marked with a
of interest to you.
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see
(Ports & Jacks)” on page A - 1
.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the
Preface
.
1 - 2 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in
. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
for installation instructions.
You will need to attach an optical device drive to the computer in order to access the drivers on the Device Drivers &
Utilities + User’s Manual disc. This contains the drivers and utilities necessary for the proper operation of the computer.
Ports and Jacks
“Ports and Jacks” on page A - 2
for a description of the interface (ports & jacks) which allow your computer to com-
municate with external devices, connect to the internet etc.
1
Overview 1 - 3
1
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8 operating system is supported.
Note: In order to run Windows 8 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Windows 8 OS
In order to run Windows 8 (32 Bit) without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM), however if you are running Windows 8 (64 bit) your computer requires a minimum 2GB of system memory (RAM).
1 - 4 Overview
Quick Start Guide
System Startup
1.
Remove all packing materials and place the computer on a stable surface.
2.
Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3.
Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
4.
Use one hand to raise the lid/LCD to a comfortable viewing angle (do not exceed 135 degrees); use the other hand (as illustrated in
Figure 1 - 1
below) to support the base of the computer (Note: Never lift the computer by the lid/LCD).
5.
Press the power button on the top right of the computer for about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).
Shutdown
Note that you should always shut your computer down by choosing the Shut Down command from the
Power item in Settings in the
Charms Bar (use the Windows
Logo Key + C key combination to access the Charms Bar) in Win-
dows 8. This will help prevent hard disk or system problems.
135
°
Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In
System Startup 1 - 5
1
1
Quick Start Guide
Figure 1 - 2
LCD Panel Open
1.
Built-In PC Camera
2.
PC Camera LED
3.
Built-In
Microphone
4.
LCD
5.
Power Button
6.
LED Indicators
7.
Keyboard
8.
Touchpad &
Buttons
System Map: LCD Panel Open
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN/
Bluetooth/3G modules are OFF if you are using the computer aboard aircraft.
Use the Airplane Mode hot key combination to toggle Airplane Mode
On/Off, and check the
LED indicator for the power status.
6
2
1
7
4
8
3
1 - 6 System Map: LCD Panel Open
5
LED Indicators
The LED indicators on the top case and front of the computer display helpful information about the current status of the computer.
Icon Color Description
Number Lock is Activated (press Num Lk)
Blue
Caps Lock is Activated (press Caps Lock)
Blue
Scroll Lock is Activated (press Fn + Scr Lk)
Blue
Table 1 - 1 - Top Case LED Indicators
Quick Start Guide
1
Icon Color
Orange
Green
Blinking
Green
Description
AC/DC Power is Plugged In
The Computer is On
The Computer is in Sleep Mode
Blinking
Orange
Orange
Green
Blinking
Orange
Green
The Powered USB Port is On
(see
“Powered USB 3.0 Port” on page 1 - 13
The Battery is Charging
The Battery is Fully Charged
The Battery Has Reached Critically
Low Power Status
Airplane Mode is ON (the WLAN/
Bluetooth/3G Modules are OFF)
Green Hard Disk Activity
Table 1 - 2 - Front Case LED Indicators
LED Indicators 1 - 7
1
Quick Start Guide
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.
NumLk & ScrLk
Hold down the Fn Key and either NumLk or
ScrLk to enable number or scroll lock, and check the LED indicator for status.
Keyboard
The illuminated keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly. The keyboard illumination level may be adjusted, or turned off/on, by using the Fn + F12 keys.
Function Keys
Play/Pause Key
NumLk &
ScrLk Keys
Numerical
Keypad
Fn Key
Menu/Application Key
Windows Logo Key
Figure 1 - 3 - Keyboard
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
1 - 8 Keyboard
Quick Start Guide
Keyboard Shortcuts
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.
Windows Logo
Key +
Description
Tap Winkey
C
D
E
R
Z
L
P
F
I
K
Toggle between the Start screen and the foremost running app or the
Windows Desktop
Display Charms menu
Switch to the Windows Desktop and toggle show Desktop
Switch to the Windows desktop and launch Windows Explorer with
Computer displayed
Display file Search
Open the Settings charm
Open the Connect charm
Lock the computer and display the Lock screen
Display the Second Screen menu (see
Switch to the Windows Desktop and display the Run dialog box
Access the App Bar (see
Figure 1 - 12 on page 1 - 19
)
Table 1 - 3 - Keyboard Shortcuts
Windows Logo
Keyboard Shortcut
Use the Windows logo
bination to switch between the Start screen and Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app is running you can use the Menu/Application key on the keyboard to display the context menu as per a mouse right-click. In the Start screen this function is useful to quickly display the All
Apps icon.
Keyboard 1 - 9
1
1
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed.
Keys
Fn + ~
Fn + Esc
Fn + 1
Function/Visual Indicators
Play/Pause (in Audio/Video Programs)
Control Center Toggle (see over)
Fan Control Toggle - Toggle between Automatic Fan Control / Full Power
Keys
Fn +F5/F6
Fn + F7
Fn +F8/F9
Function/Visual Indicators
Volume Decrease/Increase
Display Toggle
Brightness Decrease/Increase
Fn + F1
Touchpad Toggle
Fn + F10
PC Camera Power
Toggle
Fn + F2
Turn LCD Backlight Off
(Press a key to or use Touchpad to turn on)
Fn + F11
Airplane Mode
Toggle
Fn + F3
Fn + F4
Mute Toggle
Sleep Toggle
Fn + F12
Toggle Keyboard
Illumination/Adjust
Brightness Level
for Number Lock, Caps
Lock and Scroll Lock indicators
Table 1 - 4 - Function Keys & Visual Indicators
1 - 10 Keyboard
Quick Start Guide
Control Center
When in the Windows Desktop app (not in the Start screen) press the Fn + Esc key combination, or double-
click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Cen-
ter gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off
(see
Appendix B
for full details).
Control Center
Click on any button to turn any of the modules (e.g.
TouchPad, Camera) on/off.
Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes
). To remove the Power Conservation
Modes screen just click in a blank area of the icon or press a key on the keyboard.
Click on the buttons (or just click and hold the mouse button) to adjust the slider for Brightness/Volume.
Click on Display Switch and click to choose a display mode from the menu (see page
).
1
Figure 1 - 4 - Control Center
Control Center 1 - 11
1
Quick Start Guide
Figure 1 - 5
Front & Left Views
1. LED Indicators
2. Vent/Fan Intake
3. Multi-In-1 Card
Reader
4. USB 2.0 Port
5. Headphone-Out
Jack
6. Microphone-In
Jack
System Map: Front & Left Views
1
2 2
Sound Blaster
Cinema Audio
Note that you will need
to install the Sound
Blaster audio application in order to get maximum audio performance.
3
2
4
5 6
Multi-In-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
The card reader features a push-in/push-out card insertion and ejection mechanism. Simply push the card to insert and eject it, however some cards may require an adapter.
Optical Device Drives
To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports.
1 - 12 System Map: Front & Left Views
System Map: Right & Rear Views
1 2 2
3
4 5
6
7
8
USB 3.0 Port OR USB 2.0 Port
This model includes 1 * USB 2.0 port and 3 * USB 3.0 ports (including one AC/DC powered
USB 3.0 port). USB 3.0 ports are denoted by their
blue color
; USB 2.0 ports are colored black.
Powered USB 3.0 Port
The powered USB 3.0
1
port can supply power (for charging devices only, not for op-
erating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices - see page
8 - 12
). Toggle power to this port by using Fn +
power button.
Quick Start Guide
Figure 1 - 6
Right & Rear Views
1. 1 * Powered (AC/
DC) USB 3.0 Port
2. 2 * USB 3.0 Ports
3. HDMI-Out Port
4. External Monitor
Port
5. RJ-45 LAN Jack
6. DC-In Jack
7. Security Lock Slot
8. Battery
HDMI Port
Note that the HDMI Port supports video and audio signals to attached external displays. Note that Sound
Blaster audio will be disabled when you are connecting to an external display through an HDMI connection (see page
1
System Map: Right & Rear Views 1 - 13
1
Quick Start Guide
Figure 1 - 7
Bottom View
1. Battery
2. Speakers
3. Fan Outlet/Intake
4. Component Bay
Cover
System Map: Bottom View
1
3
3
4
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See
“Battery Information” on page 3 - 12
for full instructions.
3
3
3
2
CPU
The CPU is not a user serviceable part.
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
1 - 14 System Map: Bottom View
Quick Start Guide
Windows Control Panel
Throughout this manual you will see an instruction to open the Control Panel. In Windows 8 right-click the lower left hot corner to bring up the context menu (or use the Windows Logo Key + X key combination) and select Control Panel.
1
Swipe a finger from the right of the Touchpad from the
Desktop (not the Start screen) to access the Charms Bar, click Settings and click Control Panel.
Move the mouse to the bottom left of the screen and right-click to access the menu.
Figure 1 - 8 - Windows 8 Context Menu & Charms Bar Settings (from Desktop App)
Windows Control Panel 1 - 15
1
Quick Start Guide
Windows 8 Start Screen & Desktop
The Apps, control panels, utilities and programs within Windows 8 are accessed from the Start screen and/or
Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
Desktop App
Figure 1 - 9 - Windows Start Screen
1 - 16 Windows 8 Start Screen & Desktop
Quick Start Guide
Apps & Tiles
The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.
Accessing Pining/Unpinning All Apps
You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area
of the Start screen, and you will see the All Apps icon. Click the All Apps icon to display all the installed applications etc. Right-click any icon to bring up the menu at the bottom of the screen and you can then click the appropriate icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop applica-
tion.
Right-click on a blank area of the
Start Screen and click All Apps (or swipe a finger up or down on to the screen)
Right-click (or swipe down on) an icon to display the menu
1
Figure 1 - 10 - All Apps
Windows 8 Start Screen & Desktop 1 - 17
1
Quick Start Guide
Desktop Application
When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up.
When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app.
Move the mouse to the bottom left of the screen and click to switch back to the Start screen.
Figure 1 - 11 - Desktop
1 - 18 Windows 8 Start Screen & Desktop
Quick Start Guide
When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc.
Display Most
Recently Used
Apps
If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.
To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.
Move the mouse to the bottom left of the screen and right-click to access the menu.
Figure 1 - 12 - Advanced Context Menu (Right-Click lower left hot corner)
Windows 8 Start Screen & Desktop 1 - 19
1
1
Quick Start Guide
Windows 8 Charms Bar
The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share,
Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Move the mouse to the top/lower right icons to activate the Charms Bar
Move the mouse over a Charms Bar icon to activate the menu
Move the mouse to the top/lower right icons to activate the Charms Bar
Figure 1 - 13 - Start Screen with Charms Bar
1 - 20 Windows 8 Start Screen & Desktop
Quick Start Guide
Charms Bar Items
• Search : You can search for any file, application, Apps and control panel settings with instantaneous results.
• Share
: This button is used to share information with people via mail or social networks.
• Start
: Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen).
• Devices
: Click this button to change connected peripheral device settings e.g. an external display.
• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).
1
Charms Bar - TouchPad Access
To quick access the Charms Bar using the TouchPad:
1.
Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).
2.
Move your finger across to the left on to the TouchPad.
3.
The Charms Bar will then pop-up.
Figure 1 - 14 - Settings Menu
Windows 8 Start Screen & Desktop 1 - 21
1
Quick Start Guide
Windows 8 Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel can be accessed in a number of ways in Windows 8.
• Click/ Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type
Control Panel and select it from the results to the left.
Figure 1 - 15 - Search (Control Panel)
• Click on Computer (you may need to pin Computer to the Start screen) in the Start screen, click on
Computer in the top menu and select Open Control Panel from the ribbon.
Figure 1 - 16 - Open Control Panel (Computer)
1 - 22 Windows 8 Control Panel
Quick Start Guide
• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows
Charms Bar and select Control Panel from the menu.
1
Figure 1 - 17 - Settings Charms Bar (Desktop App Only)
• Right-click on a blank area of the Start screen, or swipe a finger from the top or bottom of the touch
screen. Click the All Apps icon and click Control Panel.
Figure 1 - 18 - All Apps - Control Panel
Windows 8 Control Panel 1 - 23
1
Quick Start Guide
• Right-click the lower left hot corner to bring up the menu and select Control Panel (see
Figure 1 - 12 on page 1 - 19
).
Keyboard Shortcut to Control Panel
You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key
and R
to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
1 - 24 Windows 8 Control Panel
Quick Start Guide
Windows 8 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the task-
bar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop.
The taskbar is displayed at the bottom of the desktop screen, and you can see the notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and applications referred to during the course of this manual can be accessed from here.
1
Figure 1 - 19 - Desktop Taskbar
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see
“Accessing
Pining/Unpinning All Apps” on page 1 - 17
).
Windows 8 Control Panel 1 - 25
1
Quick Start Guide
Video Features
NVIDIA
®
Optimus
™
Technology
NVIDIA
®
Optimus
™
Technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. The computer will auto-
matically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete
GPU (dGPU) when required by the applications in use.
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows 8 when running the Desktop app (see
“Desktop Application” on page 1 - 18
and
Appendix B
). In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see
“Windows 8 Charms Bar” on page 1 - 20
).
To Configure Displays from Devices (Charms Bar):
1.
Attach your display to the HDMI-Out port, and turn it on.
2.
Go the Charms Bar and select Devices.
3.
Click Second Screen.
4.
Click on any one of the options from the menu to select Duplicate, Extend or a Single display
Figure 1 - 20 - Second Screen (Devices)
1 - 26 Video Features
Quick Start Guide
1
To access Display (Control Panel) and Screen Resolution in Windows 8:
1.
Go to the Control Panel.
2.
Click Display (icon) - In the Appearance and Personalization category.
3.
Adjust resolution.
1
2
3
Right-Click Desktop App
1. You can right-click the desktop and select
Screen resolution
1
(
Figure 1 - 21
).
2. Use the dropbox to select the screen
Resolution
2
(
Figure
1 - 21
).
3. Click Advanced
settings
3
(
Figure 1 -
21
) to bring up the
Advanced properties tabs.
Figure 1 - 21 - Screen Resolution
Video Features 1 - 27
1
Quick Start Guide
To access the Intel(R) Graphics Control Panel:
1.
Click Advanced settings
3
(
Figure 1 - 21 on page 1 - 27
) in the Screen Resolution control panel in Win-
dows.
2.
Click the Intel(R)... tab and click Graphics Properties (button)
4
(
Figure 1 - 22 on page 1 - 28
) .
OR
3.
Right-click the desktop and select Graphics Properties from the menu.
OR
4.
Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
1 - 28 Video Features
4
Figure 1 - 22 - Intel HD Graphics Control Panel
To access the NVIDIA Control Panel:
1.
Right-click the desktop and select NVIDIA Control Panel
5
(
Figure 1 - 23
).
OR
2.
Double-click the icon
6
(
Figure 1 - 23
) in the Windows control panel.
Quick Start Guide
1
5
6
Figure 1 - 23 - NVIDIA Control Panel
Video Features 1 - 29
1
Quick Start Guide
Power Options
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set-
tings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/
Sleep to the menu - see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 9
).
Shut Down, Restart or Sleep
1.
Go to the Charms Bar and click Settings.
2.
Click Power .
3.
Select Sleep, Shut Down or Restart.
1 - 30 Power Options
Figure 1 - 24 - Power (Settings)
Quick Start Guide
Running Apps
To run apps in Windows 8 you will need to check that the Screen Resolution and User Account Control Set-
tings are compatible with the system requirements.
Screen Resolution Settings
1.
Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).
2.
Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).
Screen Resolution for Metro Style Apps (Windows 8)
The minimum resolution in which Metro style Apps will run is
1024x768.
The minimum resolution required to support all the features of
Windows 8 (including multitasking with snap) is 1366x768.
These specs are the minimum screen resolution that supports all the features of Windows 8 on a useful physical size.
1
Figure 1 - 25 - Screen Resolution
Running Apps 1 - 31
1
Quick Start Guide
User Account Control Settings
If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.
1.
Open the Control Panel.
2.
Click on User Accounts and then click on Change User Account Control settings (or click System and
Security and click Change User Account Control Settings under Action Center).
3.
If the slider is in the Never notify position, then the UAC is disabled.
4.
To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes
to my computer (default) position, and then click OK.
1 - 32 Running Apps
Figure 1 - 26 - User Account Control
Storage Devices, Audio & Mouse
Chapter 2: Storage Devices, Audio & Mouse
Overview
Read this chapter to learn more about the following main features and components of the computer:
2
Overview 2 - 1
2
Storage Devices, Audio & Mouse
Power Safety
Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.
Hard Disk Drive
The hard disk drive(s) is(are) used to store your data in the computer. The hard disk(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The hard disk is(are) accessible after removing the component bay cover from the bottom of your computer as seen below.
Further details on removing and inserting the hard disk are available in
“Upgrading the Hard Disk Drive(s)” on page 6 - 9
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Figure 2 - 1
Hard Disk Location
2 - 2 Hard Disk Drive
1
Storage Devices, Audio & Mouse
Multi-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver
).
• MMC (MultiMedia Card) / RSMMC
• SD (Secure Digital) / Mini SD / SDHC / SDXC
Note: Some of these cards require PC adapters that are usually supplied with the cards.
Card Reader Cover
Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.
Push-Push Card
Reader
The card reader features a push-in/push-out card insertion and ejection mechanism. Simply push the card to insert and eject it, however Ms
Duo cards require an adapter.
Figure 2 - 2
Left View
1.
Card Reader
Multi-in-1 Card Reader 2 - 3
2
2
Storage Devices, Audio & Mouse
Audio Features
Sound Volume
Adjustment
The sound volume level is set using the volume control within Windows
(and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting.
panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio
Deck control panel .
The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Click Expert Mode to access the Advanced menus
Figure 2 - 3
VIA HD Audio Deck
2 - 4 Audio Features
Storage Devices, Audio & Mouse
Expert Mode will allow you to access more advanced configuration menus for
Speaker, Microphone and Stereo Mix.
Syncing Left & Right
Volume
Balance
If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the
VIA HD Audio Deck in Expert Mode.
Click Speaker in VIA HD
Audio Deck (in Expert
Mode) and click the Sync
Left and Right volume
button (see left). You can then adjust the volume sliders independently (this setting also controls the
Balance setting in the Windows Sound control panel).
Sound Blaster Cinema Audio
Note that you will need to install the Sound Blaster Cinema audio application in order to get
maximum audio performance. See
“Sound Blaster Cinema EQ” on page 7 - 24
.
Figure 2 - 4
VIA HD Audio Deck
(Expert Mode)
2
Audio Features 2 - 5
2
Storage Devices, Audio & Mouse
Mouse Driver
If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.
Be sure to check the device’s user documentation for details.
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
2 - 6 TouchPad and Buttons/Mouse
Storage Devices, Audio & Mouse
Once you have installed the TouchPad driver (see
can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area of the taskbar in the
Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.
TouchPad Scrolling
This computer model series may feature different
TouchPad versions.
These TouchPads may differ in their vertical scrolling function in most scrollable windows.
Some TouchPads require sliding the finger up and down on the right of the
TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the
TouchPad to scroll the window.
2
Figure 2 - 5
Mouse Properties
TouchPad and Buttons/Mouse 2 - 7
2
Storage Devices, Audio & Mouse
Show Video
You can get a clearer view of the gestures involved by clicking the
Show Video option for each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Set-
tings left tree menu and click the Show Video button to see the demonstration video.
For more details on any of the gestures see the help in the lower part of the right menu window.
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1.
Go to the Control Panel.
2.
Click Mouse (Hardware and Sound).
3.
Click Device Settings (tab) and click Settings.
4.
Use the menu tree on the left to access the user configurable settings.
Figure 2 - 6
Mouse Properties -
Device Settings
2 - 8 TouchPad and Buttons/Mouse
Storage Devices, Audio & Mouse
Disabling the Touchpad
If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination.
You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached.
1.
Go to the Mouse Properties control panel.
2.
Click to select Device Settings (tab).
3.
Click to place a tick in the “Disable internal pointing device when external USB
pointing device is attached” tickbox.
4.
Click OK to save the setting.
2
Figure 2 - 7
Mouse Properties
(Disable Touchpad)
TouchPad and Buttons/Mouse 2 - 9
2
Storage Devices, Audio & Mouse
Scrolling
The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Figure 2 - 8
Scrolling Gesture
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.
Figure 2 - 9
Zooming Gesture
2 - 10 TouchPad and Buttons/Mouse
Storage Devices, Audio & Mouse
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Figure 2 - 10
Rotating Gesture
2
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
Figure 2 - 11
Flick/Press
Gesture
TouchPad and Buttons/Mouse 2 - 11
2
Storage Devices, Audio & Mouse
2 - 12
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
• Configuring the Power Buttons
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.
OS Note
Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.
3
Overview 3 - 1
3
Power Management
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1.
Attach the AC/DC adapter to the DC-in jack on the right of the computer.
2.
Plug the AC power cord into an outlet, and then connect the AC power cord to the
AC/DC adapter.
3.
Raise the lid/LCD to a comfortable viewing angle.
4.
Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see
We recommend that you do not remove the battery. For more information on the battery, please refer to
“Battery Information” on page 3 - 13
3 - 2 The Power Sources
Power Management
Turning On the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Shut Down
Note that you should always shut your computer down by choosing the Shut Down command from the Power Menu in the Set-
tings menu in the Windows 8 Charms Bar.
This will help prevent hard disk or system problems. If you want to add Hibernate/
Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 9
.
Power Button as
Stand by or
Hibernate Button
You can use the OS’s
“Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your
OS’s documentation, or
“Configuring the Power Buttons” on page 3
Figure 3 - 1
Power Menu
(Settings - Charms
Bar)
3
Turning On the Computer 3 - 3
3
Power Management
Resuming
Operation
See
Table 3 - 1, on page 3 - 10
for information on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in order to protect your data.
Power Plans
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Figure 3 - 2
Power Plan
Advanced Settings
3 - 4 Power Plans
Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Click to Show/Hide additional power plans
Figure 3 - 3
Power Plans
Power Plans 3 - 5
3
Power Management
Wake On LAN
Support
(Windows 8)
Wake-On-LAN is only supported from Sleep or
Hibernate states in
Windows 8.
If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hiber-
nate.
Wake-On-LAN is not supported from Shutdown states in Win-
dows 8.
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.
To add Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power
Menu” on page 3 - 9
.
3 - 6 Power-Saving States
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the
Power Menu see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 9
.
Shut down
You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.
Power Management
3
Figure 3 - 4
Power Menu
Power-Saving States 3 - 7
3
Power Management
Password
Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can disable this setting from the
Power Options menu by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that are currently unavail-
able).
Configuring the Power Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Figure 3 - 5
Power Options
Define Power
Buttons
3 - 8 Configuring the Power Buttons
Adding Hibernate/Sleep to the Power Menu
Add Hibernate/Sleep to the Power Menu as follows.
1.
Go to the Power Options (Hardware and Sound) control panel
(see page
1 - 23
)
.
2.
Click “Change settings that are currently unavailable” .
3.
Click Choose what the power buttons do.
4.
Click to put a tick in the Hibernate/Sleep box under Shutdown settings.
5.
Click Save Changes and close the control panel.
Power Management
3
Figure 3 - 6
Power Options
Define Power
Buttons - Shutdown
Settings
Configuring the Power Buttons 3 - 9
3
Power Management
Table 3 - 1
Resuming
Operation
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status To Resume
Power Off
Sleep
Off
Blinking Green
Press the Power Button
Press the Power Button
Press the Sleep Button (Fn + F4 Key Combo)
Hibernate
Display Turned Off
Off (battery)
Orange (AC/DC adapter)
Green
Press the Power Button
Press a Key or Move the Mouse/Touchpad
Closing the Lid
If you have chosen to send the computer to
Sleep when the lid is closed, raising the lid will wake the system up.
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
3 - 10 Configuring the Power Buttons
Power Management
Power Conservation Modes
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:
1.
Press the Fn + Esc key combination to toggle the Control Center on/off.
2.
Click either the Performance, Balanced or Energy Star button.
3.
Click in a blank area of the icon or press a key on the keyboard to exit Power
Conservation Mode without making any changes.
Power Conservation
Modes
The Energy Star setting will result in maximum power saving, but with the possible loss of some performance.
Setting the mode to Bal-
ance will give power saving matched with performance.
Performance will give optimum computer performance but with less power conservation.
3
Figure 3 - 7
Control Center
Configuring the Power Buttons 3 - 11
3
Power Management
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination from almost any of the Win-
dows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log
off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Figure 3 - 8
Ctrl + Alt + Delete
Menu
To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to perform the function selected.
3 - 12 Configuring the Power Buttons
Power Management
Battery Information
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see
Figure
3 - 3 on page 3 - 5
).
Click the battery icon in the notification area to see the current battery level and charge status.
Low Battery
Warning
When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.
3
Figure 3 - 9
Battery Icon
(Notification Area) &
Battery Advanced
Settings
Battery Information 3 - 13
3
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Conserving Battery Power
• Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth, modem or communication applications when they are not being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
Figure 3 - 10
Windows Mobility
Center
3 - 14 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see
“Removing the Battery” on page 6 - 4
New Battery
Always completely discharge, then fully charge, a new battery (see
for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. Refer to
“LED Indicators” on page 1 - 7
for information on the battery charge status, and to
“Battery Information” on page 3 - 13
for more information on how to maintain and properly
recharge the battery pack.
Power Management
3
Battery Information 3 - 15
3
Power Management
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.
3 - 16 Battery Information
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1.
Save and close all files and applications.
2.
Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Figure 3 - 11
Power Plan Create
Battery Information 3 - 17
3
Power Management
3.
Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings.
Figure 3 - 12
Change Plan
Settings / Change
Advanced Power
Settings
3 - 18 Battery Information
4.
Scroll down to Battery and click + to expand the battery options.
5.
Choose the options below (click Yes if a warning appears):
Power Management
3
Figure 3 - 13
Power Options
Advanced Settings -
Battery
• Low battery levels = 0%
• Critical battery Levels = 1%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
Battery Information 3 - 19
3
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
3 - 20 Battery Information
Drivers & Utilities
Chapter 4: Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.
What to Install
You will need to attach an external DVD drive to install the drivers from the
Device Drivers & Utilities + User’s Manual
disc.
Table 4 - 1, on page 4 - 3
lists what you need to install and it is very important that the drivers are installed in the or-
der indicated.
Module Driver Installation
The procedures for installing drivers for the PC Camera, WLAN and Combination
Bluetooth & WLAN modules (you should also install the Sound Blaster Cinema,
Intel Technology drivers as instructed in Chapter 7) are provided in
.
Driver Installation &
Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a work-
ing power source.
Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems
(note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
4
What to Install 4 - 1
4
Drivers & Utilities
Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into into an attached optical (DVD) drive
.
2.
Click the message “Tap to choose what happens
with this disc.”
3.
Click Run autorun.exe.
4.
Click Install Drivers (button), or Option Drivers
(button) to access the Optional driver menu.
5.
Check the driver installation order from
Table 4 - 1, on page 4 - 3
(the drivers must be installed in this order) which is the same as that listed in the Drivers
Installer menu below.
6.
Click to select the driver you wish to install, (you should note down the drivers as you install them).
7.
Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure 4 - 1
- Drivers Installer Screen 1
4 - 2 Driver Installation
Figure 4 - 2
- Install Drivers
Drivers & Utilities
Win 8 System Driver
Page #
Optional
Setting Up SATA RAID or AHCI Mode
(No driver required)
Intel® Rapid Storage Technology
(required for hard disks in AHCI mode)
Intel® Rapid Start Technology Driver
Page #
Intel® Wireless Display Application
Table 4 - 1
- Driver Installation
All drivers provided are for the Windows 8 operating system.
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
4
Driver Installation 4 - 3
4
Drivers & Utilities
Manual Driver Installation
Click Browse CD/DVD (button) in the Drivers Install-
er application and browse to the executable file in the appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See
“Windows Update” on page 4 -
8
for instructions.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1.
Go to the Control Panel).
2.
Double-click Device Manager (Hardware and
Sound > Devices and Printers > Device
Manager).
3.
Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4.
Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
4 - 4 Driver Installation
Drivers & Utilities
User Account Control
If a User Account Control prompt appears as part of the driver installation procedure, click Continue or
Allow, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this
driver software anyway” or “Install” to continue the installation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” during the installation procedure (other than when out-
lined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter
(and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver.
Make sure any modules (e.g. WLAN or Bluetooth) are
ON (i.e. the system is not in Airplane Mode) before installing the appropriate driver.
4
Driver Installation 4 - 5
4
Drivers & Utilities
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual disc into your attached CD/DVD drive and click In-
stall Drivers (button).
Note: After installing the video driver go to the Dis-
play/Display Settings control panel to adjust the video settings to the highest resolution.
Chipset
1.
Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
LAN
1.
Click 4.Install LAN Driver > Yes.
2. Click Next > Install.
3. Click Finish.
Video (VGA)
1.
Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Card Reader
1.
Click 5.Install Cardreader Driver > Yes.
2. Click Finish.
NVIDIA Video (VGA)
1.
Click 3.Install NVIDIA VGA Driver > Yes.
2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement.
3. Click Next.
4. Click Close to complete the installation.
TouchPad
1.
Click 6.Install Touchpad Driver > Yes.
2. Click Next.
3. Click the button to accept the license, and then click Next.
4. Click Finish > Restart Now to restart the computer.
4 - 6 Driver Installation
Airplane
1.
Click 7.Install Airplane AP > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Drivers & Utilities
Audio
1.
Click 10.Install Audio Driver > Yes.
2. Click Next.
3. Click the button to agree to the license and click Next.
4. Click Next > Next > Next.
5. Click Finish to restart the computer.
Hot Key
1.
Click 8.Install Hotkey AP > Yes.
2. Click Next > Next.
3. Click Finish > Finish to restart your computer.
MEI Driver
1.
Click 9.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish.
After installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers, eject the Device Drivers & Utili-
ties + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click
Option Drivers (button) to access the optional driver menu.
It is recommended that you install the Sound Blaster
Audio application for maximum audio performance
“Sound Blaster Cinema EQ” on page 7 - 33
) and Intel
Rapid Storage Technology driver (see
Storage Technology” on page 7 - 38
or RAID mode).
4
Driver Installation 4 - 7
4
Drivers & Utilities
Windows Experience Index
After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi-
ence Index (make sure the AC/DC adapter is plugged in):
1.
Go to the Control Panel.
2. Click Performance Information and Tools
(System and Security > System > Windows
Experience Index).
3. Click “Rate this computer/Refresh Now/Re-
run the assessment”.
4. The computer will take a few minutes to assess the system performance.
5. Close the control panel.
Windows Update
After installing all the drivers make sure you enable Win-
dows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1.
Go to the Control Panel.
2.
Click Windows Update (System and Security/
Security).
3.
Click Check for updates (button).
4.
The computer will now check for updates (you need to be connected to the internet).
5.
Click Install now (button) to begin checking for the updates.
6.
Click Install updates (button) to install the updates.
4 - 8 Driver Installation
Drivers & Utilities
Optional Drivers
See the pages indicated in
Table 4 - 1, on page 4 - 3
for the driver installation procedures for any modules included in your purchase option.
4
Models A & B
Figure 4 - 3
- Optional Drivers Installer Screen
Note that you need to install both the WLAN & Bluetooth drivers for all the Bluetooth Combo modules.
Driver Installation 4 - 9
4
Drivers & Utilities
4 - 10
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s
BIOS.
BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
5
Overview 5 - 1
5
BIOS Utilities
The Power-On Self Test (POST)
If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options.
Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
BIOS Utilities
5
The Power-On Self Test (POST) 5 - 3
5
BIOS Utilities
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct mistakes, return to Set-
up and restore the Pre-
vious Values with
<F2>, or Optimized De-
faults with <F3>.
The Setup Utility
The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) during the POST (or press F7 for boot options). If you get a
“Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
To see the boot options press F7.
5 - 4 The Setup Utility
BIOS Utilities
Setup Screens
The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options.
5
Figure 5 - 1
Navigation Menu
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the upper right side of each screen explains the highlighted item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
The Setup Utility 5 - 5
5
BIOS Utilities
Figure 5 - 2
Main Menu
Main Menu
5 - 6 Main Menu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
SATA Port # (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a optical Device/
HDD on the computer’s SATA Ports.
System/Extended Memory (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
MB Series / BIOS Revision / KBC/EC Firmware Revision (Main Menu)
This item contains information on the BIOS version and video card etc., and is not user configurable.
BIOS Utilities
5
Main Menu 5 - 7
5
BIOS Utilities
Advanced Menu
Figure 5 - 3
Advanced Menu
5 - 8 Advanced Menu
Advanced Chipset Control (Advanced Menu)
The sub-menu here allows you to adjust the Bluetooth Power Setting.
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)
You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
Intel(R) Rapid Start Technology (Advanced Menu)
Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power.
Intel(R) Rapid Storage Technology (Advanced Menu)
Enable/disable Intel(R) Rapid Storage Technology from this menu to provide high-performance SATA RAID capabilities for Windows 8. Note that this menu item will be available if UEFI Boot is enabled (in the OS Select sub-menu) and the
SATA Mode (Advanced Menu) is set to RAID (see below). See
RAID or AHCI Mode” on page 7 - 2
BIOS Utilities
5
Advanced Menu 5 - 9
5
BIOS Utilities
SATA Mode
Selection
If you have installed the
Windows
operating system with either IDE,
AHCI or RAID mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows OS).
Intel Anti-Theft Technology (Advanced Menu)
Anti-Theft Technology, which is built-in to the processor of the computer, allows system administrators to render your computer useless to thieves by sending a poison pillencrypted SMS message over a 3G network etc. Administrators can also remotely unlock a recovered computer quickly, or direct the system to send location information (GPS coordinates) back to a central server.
SATA Mode (Advanced Menu)
You can configure SATA (Serial ATA) control to operate in IDE (native/compatible), AHCI (Advanced Host Controller Interface) or RAID (Redundant Array of Independent disks) modes from this menu. A RAID mode may be set if you have
included 2 * mSATA SSDs in your purchase configuration. The SATA Mode should be set BEFORE installing an operating system, and after you have backed
up all necessary files and data (see sidebar). See
Make sure you install the Intel Rapid Storage Technology application if you have set the SATA Mode to RAID or AHCI (see
“Intel® Rapid Storage Technology” on page 7 - 38
5 - 10 Advanced Menu
Boot Logo (Advanced Menu)
Use this menu item to enable/disable the Boot Logo screen at system startup if you
have not enabled UEFI Boot. If you disable the Boot Logo you will not see the F2
Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot
Option functions.
When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear.
However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities
5
Advanced Menu 5 - 11
5
BIOS Utilities
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.
These settings do not affect your machine or network passwords which will be set in your software OS.
Security Menu
Figure 5 - 4
Security Menu
5 - 12 Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities
Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Note: You can only set the user password after you have set the supervisor pass-
word.
Password on boot: (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.
Secure Boot (Security Menu)
Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have
Windows 8 set as your operating system, and have enabled UEFI Boot (see
). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy), or Custom (which enables you to make changes to the Image Execution
Policy and Key Management database).
Password Warning
If you set a boot password (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
5
Security Menu 5 - 13
BIOS Utilities
Boot Menu
Figure 5 - 5
Boot Menu
5
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s
BIOS.
BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
When you turn the computer on it will look for an operating system (e.g. Windows
7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities. Item specific help on the right is available to help you move devices up and down the order.
5 - 14 Boot Menu
Boot Option Priorities (Boot Menu)
Use the arrow keys to move up and down the menu, and press enter to select a device from the menu (the selected device will be highlighted in white).
UEFI Boot (Boot Menu > OS Select)
Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services. The Network Stack item will be enabled as an option under UEFI Boot.
BIOS Utilities
5
Boot Menu 5 - 15
5
BIOS Utilities
Figure 5 - 6
Exit Menu
Exit Menu
5 - 16 Exit Menu
Click Save Changes and Reset to save all changes made. Choosing to Discard
Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Component Bay Cover
• Upgrading the Hard Disk Drive(s)
• Upgrading the System Memory (RAM)
Please make sure that you review each procedure before you perform it.
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
6
Overview 6 - 1
6
Upgrading The Computer
Power Safety Warning
Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
You must also remove your battery in order to prevent accidentally turning the machine on.
Before removing the battery disconnect the
AC/DC adapter from the computer.
When Not to Upgrade
These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if:
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
6 - 2 Overview
Upgrading The Computer
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
6
Overview 6 - 3
6
Upgrading The Computer
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/
DC adapter from the computer first.
1.
Turn the computer off, remove the AC/DC adapter and turn it over.
2.
Slide the latch
1
in the direction of the arrow.
3.
Slide the latch
2
in the direction of the arrow and hold it in place.
4.
While holding latch
2
, slide the battery
3
out of the compartment.
2 1
Figure 6 - 1
Battery Unlock
2 1
3
6 - 4 Removing the Battery
Upgrading The Computer
Inserting the Battery
1.
Slide the battery
1
straight into the compartment (note that there are grooves on the side of the battery which should align up with the battery compartment).
2.
Lock the battery in place by sliding the latches in the direction of arrows
2
&
3
.
1
Figure 6 - 2
Battery Insertion &
Lock
6
2 3
Removing the Battery 6 - 5
Upgrading The Computer
Removing the Component Bay Cover
1.
Turn off the computer, and turn it over and remove the battery.
2.
Locate the component bay cover and remove screws
1
-
3
.
6
Figure 6 - 3
Component Bay
Cover Screws
3
1
6 - 6 Removing the Component Bay Cover
2
Upgrading The Computer
3.
Lift the cover up at point
4
and remove the cover
5
the direction of arrow
6
.
4
5
6
Figure 6 - 4
Component Bay
Cover Removal
6
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
• Do not touch the heat sink area as the parts may be hot.
Removing the Component Bay Cover 6 - 7
6
Upgrading The Computer
Replacing the Component Bay Cover
1.
Reinsert the component bay cover by placing it on the bottom case assembly and aligning the three pins
1
-
3
with the slots in the case.
2.
Angle the cover up to make sure that the cover pins fit in the slots, and then place the cover down onto the computer and ensure that the fit is tight before replacing the screws
1
-
3
Figure 6 - 5
Component Bay
Cover Replacement
1
2
3
6 - 8 Removing the Component Bay Cover
Upgrading The Computer
Upgrading the Hard Disk Drive(s)
The hard disk Drive(s) can be taken out to accommodate up to one other 2.5" serial
(SATA) hard disk drives with a height of 9.5mm (h) (see
).
Follow your operating system’s installation instructions, and install all necessary
drivers and utilities (as outlined in
“Drivers & Utilities” on page 4 - 1
up a new hard disk.
HDD System Warning
New HDD’s are blank. Before you begin make sure:
You have backed up any data you want to keep from your old HDD.
You have all the CD-ROMs and FDDs required to install your operating system and programs.
If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
6
Upgrading the Hard Disk Drive(s) 6 - 9
6
Upgrading The Computer
Removing the Hard Disk
1.
Turn off the computer, and turn it over and remove the battery and component bay covers (see pages
2.
Slide the HDD cover in the direction of arrow
1
, and lift it out of the bay
2
.
3.
Remove screws
3
&
4
and the cover
5
.
1
2
Figure 6 - 6
Primary HDD
Removal
4
5
3
6 - 10 Upgrading the Hard Disk Drive(s)
Upgrading The Computer
Reinserting the Hard Disk
1.
Reverse the process to install a new disk and do not forget to reinstall the cover
).
2.
Place the hard disk assembly into the bay and slide it in the direction of arrow
3.
Replace the component bay cover (see page
).
1
.
1
Figure 6 - 7
Inserting the Hard
Disk
6
5
Upgrading the Hard Disk Drive(s) 6 - 11
6
Upgrading The Computer
Upgrading the System Memory (RAM)
The computer has two memory sockets for 204 pin Small Outline Dual In-line (SO-
DIMM) DDR3L type memory modules (see
memory size is automatically detected by the POST routine once you turn on your computer.
6 - 12 Upgrading the System Memory (RAM)
Upgrading The Computer
1.
Turn off the computer, and turn it over and remove the battery and component bay
&
2.
The memory sockets will be visible at point
1
on the mainboard.
Figure 6 - 8
RAM Module
Location
1
3.
Gently pull the two release latches (
2
&
3
)
on the sides of the memory sockets) in the direction indicated below.
Contact Warning
Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
2 3
Figure 6 - 9
RAM Module
Release Latches
6
Upgrading the System Memory (RAM) 6 - 13
6
Upgrading The Computer
4.
The RAM module will
4
pop-up, and you can remove it.
Figure 6 - 10
RAM Module
Removal
Single Memory Module
Installation
If your computer has a single memory module, then insert the module into the
Channel 0 (JDIMM1) socket. In this case this is the lower memory socket
(the socket closest to the mainboard).
Contact Warning
Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
4
5.
Pull the latches to release the second module if necessary.
6.
Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket.
7.
The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go. DO NOT FORCE the module; it should fit without much pressure.
8.
Press the module in and down towards the mainboard until the socket levers click into place to secure the module.
9.
Replace the component bay cover (see page
6 - 14 Upgrading the System Memory (RAM)
Modules
Chapter 7: Modules
Overview
This chapter contains the information on the various modules (some of which are
optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
The chapter includes information on the following:
• Setting Up SATA RAID or AHCI Mode
• Bluetooth & WLAN Combo Module
• Intel® Rapid Storage Technology
• Intel® Smart Response Technology
• Intel® Rapid Start Technology Driver
• Intel® Wireless Display Application
You will need to attach an optical device drive to the computer in order to access the drivers on the Device Drivers & Utilities + User’s Manual disc.
Overview 7 - 1
7
7
Modules
RAID Solid State
Drives (SSDs)
All mSATA SSDs in a
RAID should be identical (the same size and brand) in order to prevent unexpected system behavior.
SATA Mode
Selection
The SATA mode selection should be made be-
fore installing your
operating system.
DO NOT change your selected SATA mode
unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so.
Setting Up SATA RAID or AHCI Mode
AHCI Mode
Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced serial ATA features such as Native Command
Queuing (for maximum hard disk efficiency and performance). Make sure you install the Intel® Rapid Storage Technology application if you have set up your hard
“Intel® Rapid Storage Technology” on page 7 - 38
RAID
To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0), Mirroring (RAID 1) or Recovery modes (see
Table 7 - 1, on page 7 -
3
) you will require at least two identical (see sidebar) mSATA solid state drives
(SSDs). Note that you will need to install a driver from the Device Drivers & Utili-
ties + User’s Manual disc at OS installation (see page
).
Intel
®
Rapid Storage Technology Application
Make sure you install the Intel® Rapid Storage Technology application if you have set up your hard disk in AHCI mode or mSATA SSD’s in RAID mode (see
“Intel® Rapid Storage Technology” on page 7 - 38
7 - 2 Setting Up SATA RAID or AHCI Mode
RAID Level
RAID 0
RAID 1
Recovery
Description
Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive.
Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data. When a new replacement drive is installed, data to the new drive is rebuilt from the mirrored drive to restore fault tolerance.
Two Identical drives copying data between a master and a recovery disk. This provides more control over how data is copied between the master and recovery drives, fast volume updates and the ability to view the data in Windows Explorer.
SATA Mode Selection
The SATA mode selection should be made before installing your operating system.
DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so.
RAID Solid State Drives (SSDs)
All mSATA SSDs in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior.
Modules
Table 7 - 1
RAID Levels
Array Types
A
Mirrored Array
(RAID 1) provides full data protection, as data can simply be copied from a healthy disk to a replacement for any failed disk.
A
Striped Array
(RAID 0) is NOT faulttolerant. The failure of one drive will result in the loss of all data in the array. It is designed to increase disk performance by spreading the I/O load across the channels and drives.
7
Setting Up SATA RAID or AHCI Mode 7 - 3
7
Modules
SATA RAID Setup Procedure (Windows 8)
To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0) or Mirroring (RAID 1) modes (see
Table 7 - 1, on page 7 - 3
) you will require at least two identical (see sidebar) mSATA solid state drives (SSDs) in-
stalled.
You need to setup a RAID before installing your Windows 8 operating system, and you will need to prepare the following in order to do so.
1.
The Microsoft Windows 8 OS DVD.
2.
Two (identical) mSATA solid state drives installed (note that hard disk drive will be used for data storage only in a mSATA SSD RAID configuration).
3.
You will need to attach an external DVD drive to install the drivers from the
Device Drivers & Utilities + User’s Manual disc.
4.
The Device Drivers & Utilities + User’s Manual disc.
5.
A USB flash drive.
6.
An operable computer (to copy files from the Device Drivers & Utilities +
User’s Manual disc to the USB flash drive).
Before setting up the system you will need to copy a driver folder to a USB flash drive or external USB hard disk. This driver folder is included on the Device Drivers
& Utilities + User’s Manual disc but you will need to go to an operable computer and copy the folder to a USB Flash drive or external USB hard disk.
7 - 4 Setting Up SATA RAID or AHCI Mode
Modules
1.
Go to the operable computer and insert a USB Flash drive or external USB hard disk.
2.
Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive of the operable computer.
3.
Copy the f6flpy-x86 or f6flpy-x64 folder from the location below (D: denotes your
DVD drive) on the Device Drivers & Utilities + User’s Manual disc to the USB flash drive or external USB hard disk.
• For Windows 8 32bit = D:\Options\RAID\f6flpy-x86
• For Windows 8 64bit = D:\Options\RAID\f6flpy-x64
4.
Start-up your notebook computer and press <F2> to enter the BIOS.
5.
Go to the Boot menu, select UEFI Setting and press <Enter> (see page
6.
Set UEFI Boot to “Enabled”.
7.
Press <Esc> to exit the menu and go to the Advanced menu.
8.
), press <Enter> and select “RAID Mode”.
9.
Press <F4> and <Yes> to “Save Changes and Reset”.
10. After computer restarts press <F2> to enter the BIOS again.
11. Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press
<Enter>.
12. Select Create RAID Volume and press <Enter>.
Figure 7 - 1
Create RAID Volume
(Advanced > Intel(R)
Rapid Storage
Technology
7
Setting Up SATA RAID or AHCI Mode 7 - 5
Modules
13. You can now setup your RAID volume using any installed SSDs.
14. Go to Name: and press <Enter>.
15. Type a name of your choice for your RAID volume and press <Enter>.
7
Figure 7 - 2
Name the RAID
Volume (Advanced
> Intel(R) Rapid
Storage
Technology)
7 - 6 Setting Up SATA RAID or AHCI Mode
Modules
16. Go to RAID Level: and press <Enter>.
17. Choose the RAID Level required (see
Table 7 - 1, on page 7 - 3
for details) and press <Enter>.
• RAID0 (Stripe)
• RAID1 (Mirror)
• Recovery
18. Go to any of the disks listed under Select Disks: and select a drive name and press <Enter>.
19. Move the cursor down (use the arrow keys) onto to X (o select the SSD drives required and press <Enter>.
• If you have selected a Recovery level RAID then you need to select one drive to be Master disk (M) and one disk to be the Recovery disk (R)
For Recovery
Figure 7 - 3
Select Disks
(Advanced > Intel(R)
Rapid Storage
Technology)
For Stripe or Mirror
7
Setting Up SATA RAID or AHCI Mode 7 - 7
Modules
7
Figure 7 - 4
Created RAID
Information
(Advanced > Intel(R)
Rapid Storage
Technology)
20. You should select two identical mSATA SSDs to form your RAID volume.
21. If you have selected RAID0 (Stripe) then you can adjust the “Strip Size” to your requirements.
22. If you have selected Recovery then you can adjust the Synchronization to “On
Request” or “Continuous”.
23. Go to Create Volume and press <Enter>.
24. The RAID volume will then be created and the RAID information will be displayed under Intel(R) Rapid Storage Technology (in the Advanced menu).
7 - 8 Setting Up SATA RAID or AHCI Mode
Modules
25. Press <Esc> to exit the menu.
26. Go to the Boot menu and make sure your attached DVD drive is set as Boot
Option #1 in Boot Option Priorities.
Figure 7 - 5
Boot Option
Priorities (Set
Attached DVD Drive as Option #1)
27. Press <F4> and <Yes> to “Save Changes and Reset”, however ensure that the
two conditions in the bulleted points below are met before doing so.
• Make sure the Windows 8 OS DVD is in the attached DVD drive. and as the computer starts up it will automatically boot from the Windows 8 OS DVD (you will be prompted to press a key to boot from the DVD).
• Make sure your USB Flash drive or external USB hard disk is attached to one of the USB ports on the computer.
28. Press <F7> as the computer starts up to bring up the boot device menu.
29. Select the DVD drive containing the Windows 8 OS DVD and press <Enter>.
30. Press a key at system startup to begin installing Windows from your Microsoft
Windows 8 disc.
31. Click Next > Install Now to continue installing the operating system as normal
(see your Windows documentation if you need help on installing the Windows
OS).
32. A prompt will appear to ask you to Load Driver.
Setting Up SATA RAID or AHCI Mode 7 - 9
7
7
Modules
33. Click Browse and browse to the location you copied the files to on your USB Flash drive or external USB hard disk (X: denotes your USB Flash drive or external USB hard disk):
• X:\f6flpy-x86 (for Windows 8 32bit)
• X:\f6flpy-x64 (for Windows 8 64bit)
34. Click Next.
35. Follow the on-screen instructions to install the Windows 8 operating system.
36. Install the Windows drivers from the Device Drivers & Utilities + User’s Manual disc as per
(make sure you install the Intel Rapid
Storage Technology driver - see overleaf).
37. Run the Intel® Rapid Storage Technology application to manage your RAID volume as instructed in
“Intel® Rapid Storage Technology for RAID Systems” on page 7 - 39
.
IRST Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3.
Click 4.Install IRST Driver > Yes.
4. Click Next > Next.
5. Click the tickbox to accept the license and click Next.
6. Click Next > Next > Next.
7. Click Finish to restart the computer.
“Intel® Rapid Storage Technology for RAID Systems” on page 7 - 39
.
7 - 10 Setting Up SATA RAID or AHCI Mode
Modules
Deleting a RAID (Windows 8)
If you wish to delete an existing RAID then follow the procedure below to do so. However backup up any necessary files and data before deleting a RAID, as doing so will result in the loss of all data on the RAID volumes.
1.
Start-up your notebook computer and press <F2> to enter the BIOS.
2.
Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press
<Enter>.
3.
Go to the RAID (listed under RAID Volumes:) and press <Enter>.
4.
Select Delete and press <Enter>.
5.
Select “Yes” (note that al the data on the volumes will be lost) and press <Enter>.
Figure 7 - 6
Delete RAID
(Advanced > Intel(R)
Rapid Storage
Technology)
7
Setting Up SATA RAID or AHCI Mode 7 - 11
7
Modules
PC Camera Module
When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red
use the Camera app in Windows 8 to take pictures and capture video. Use the Fn +
F10 key combination (see
“Function Keys & Visual Indicators” on page 1 - 10
to toggle power to the PC Camera module.
7 - 12 PC Camera Module
Modules
PC Camera Audio Setup
If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows.
1.
Go to the Control Panel.
2.
Click Sound (Hardware and Sound) and click Recording (tab).
3.
Right-click hold and release Microphone (VIA High Definition Audio) and make sure the item is not disabled.
4.
Double-click Microphone (or select Properties from the right-click menu).
5.
Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required.
6.
Click OK and close the control panels.
Figure 7 - 7
Audio Setup for PC
Camera
7
Right-click
PC Camera Module 7 - 13
7
Modules
Camera App
1.
Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module).
2.
Click the Camera app icon in the Start screen to run the Camera app
3.
The camera interface is a translucent app bar with three buttons.
.
Figure 7 - 8
Camera App Bar
Figure 7 - 9
Camera Options
• Camera options:. Click this button to open a window with three main options:
Camera Options
• Resolution (determined by the camera spec)
• Audio device (select microphone to use)
• Video Stabilization (a toggle based on spec of the camera)
7 - 14 PC Camera Module
Modules
You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here).
Eliminating Screen
Flicker
If you find that the video screen in the camera program is flickering, you can try to adjust the setting in
Flicker under More Op-
tions.
Figure 7 - 10
More Camera
Options
7
• Timer: This button will start a three second countdown before the system takes a still photo or video recording starts.
• Video Mode: This button toggles between still photo mode (transparent button
) and video recording mode (highlighted white button ).
PC Camera Module 7 - 15
Modules
7
Figure 7 - 11
Libraries - Pictures
Taking Pictures/Capturing Video
1.
Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module).
2.
Click the Camera app icon in the Start screen to run the Camera app
3.
Click to select the timer if you require a countdown before capture.
.
4.
Click to select either photo or video modes.
5.
Click in the main window to take a picture or start video capture (if video capture begins a timer will appear in the bottom right corner of the screen).
6.
To stop video capture click the main window again.
7.
Captured photos and videos will be saved to a Camera Roll folder within the
Picture folder in Libraries.
7 - 16 PC Camera Module
Modules
8.
A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured.
9.
Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app.
10. Clicking on a captured photo will bring up an app bar with Crop and Delete buttons.
Figure 7 - 12
Crop & Delete
Buttons
(for Still Photos)
11. Use the handles to Crop any captured picture, and click OK to save the changes made.
12. Click Delete to delete any captured photo (note that no prompt will appear to confirm the delete).
13. Right-click any captured video to bring up app bar with Trim and Delete buttons.
14. Use the buttons at either end of the slider to adjust the video length and click OK to save the changes made.
Figure 7 - 13
Trim & Delete
Buttons
(for Video Files)
7
PC Camera Module 7 - 17
7
Modules
Reducing Video File Size
Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My
Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Note that the Windows 8 system requires a minimum of 16GB (32-bit) or 20GB (64-
bit) of free space on the C: drive system partition. In order to prevent system problems it is recommended that you move any large sized captured video file to a location other than the C: drive, or reduce video resolution (see below).
To Reduce Video Resolution Output Size:
1.
Run the Camera app.
2.
Click the Video resolution dropbox and select a lower resolution size in order to reduce the captured file size.
3.
Note that reducing video resolution will affect the video quality.
7 - 18 PC Camera Module
Modules
Wireless LAN Module
If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver.
Make sure you install the drivers in the order indicated in
.
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN
& Bluetooth Combo modules.
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
Bluetooth and 3G
module(s) are OFF if you are using the computer aboard aircraft by putting the system in to
Airplane Mode (see
).
7
Wireless LAN Module 7 - 19
7
Modules
3rd Party 802.11b/g/n Driver Installation
1.
Make sure the system is not in Airplane Mode, and then insert the Device
Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
1.Install WLAN Driver > Yes.
4.
Click Next.
5.
Click
Finish to restart the computer.
6. The operating system is the default setting for Wireless LAN control in
Windows (see page
7 - 21
Intel® WLAN Driver Installation
1.
Make sure the system is not in Airplane Mode, and then insert the Device
Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
1.Install WLAN Driver > Yes.
4.
Click in the tickbox to agree to the End User License Agreement and click
Install.
5.
Click
Finish.
6. The operating system is the default setting for Wireless LAN control in
Windows (see page
7 - 21
7 - 20 Wireless LAN Module
Modules
WLAN Configuration in Windows 8
You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins.
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
3.
A list of available access points will appear.
Figure 7 - 14
WiFi Settings
(Charms Bar) &
Networks
7
Wireless LAN Module 7 - 21
Modules
4.
Double-click an access point to connect to it (or click it and click Connect).
5.
Enter a network security key (password) if required, and click Next.
6.
You can choose to share or connect to devices or not.
7.
When you are connected to the network access point it will display the Connected icon .
8.
Select any connected network and click Disconnect connected access point.
to disconnect from a
7
Figure 7 - 15
Networks
Connected /
Disconnect
9.
You can click the Airplane Mode button to turn the mode On or Off.
10. If you click on Change PC Settings (at the bottom of Settings in the Charms Bar) you can turn Wireless or Airplane Mode On/Off (see over).
7 - 22 Wireless LAN Module
11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft.
Modules
Figure 7 - 16
PC Settings
(Wireless)
7
Wireless LAN Module 7 - 23
Modules
7
Figure 7 - 17
Windows Desktop
Taskbar Notification
Area WLAN
Connection
Desktop Mode
1.
Switch to the Windows Desktop (click the app or use the Windows logo key +
D key combination).
2.
Click the wireless icon in the notification area of the taskbar.
3.
A list of available access points will appear.
4.
Double-click an access point to connect to it (or click it and click Connect).
5.
Enter a network security key (password) if required, and click Next.
6.
You can choose to share or connect to devices or not.
7.
Select any connected network and click Disconnect to disconnect from a connected access point.
7 - 24 Wireless LAN Module
Modules
Control Panel
If you are in Category View do the following (see over for Icon View):
1.
Open the Control Panel.
2.
Click the Network and Internet control panel.
3.
Click Connect to a network.
Figure 7 - 18
Network and
Internet Control
Panel
7
4.
A list of available access points will appear.
5.
Double-click an access point to connect to it (or click it and click Connect).
6.
Enter a network security key (password) if required, and click Next.
7.
You can choose to share or connect to devices or not.
8.
Select any connected network and click Disconnect to disconnect from a connected access point.
Wireless LAN Module 7 - 25
Modules
If you are in Icon View do the following:
1.
Open the Control Panel.
2.
Click Network and Sharing Center.
3.
Click Change Adapter Settings.
4.
Double-click Wi-Fi.
7
Figure 7 - 19
Network and
Sharing Center
Control Panel
5.
A list of available access points will appear.
6.
Double-click an access point to connect to it (or click it and click Connect).
7.
Enter a network security key (password) if required, and click Next.
8.
You can choose to share or connect to devices or not.
9.
Select any connected network and click Disconnect to disconnect from a connected access point.
7 - 26 Wireless LAN Module
Bluetooth & WLAN Combo Module
If your purchase option includes the Combination Wireless LAN & Bluetooth
module (either Intel® or 3rd Party) then install the driver as instructed overleaf.
Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver.
Bluetooth Data Transfer
Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
Modules
7
Bluetooth & WLAN Combo Module 7 - 27
7
Modules
High Speed Bluetooth
Data Transfer
The Combination Wire-
less LAN & Bluetooth
module supports high speed data transfer. However to achieve such transfer speeds, both de-
vices must support high speed data trans-
fer.
To obtain high speed data transfer make sure that both the WLAN and
Bluetooth modules are powered on.
Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer.
3rd Party Bluetooth (V4.0) Combo Driver Installation
1.
Make sure the system is not in Airplane Mode, and then insert the Device
Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
2.Install Combo BT Driver > Yes.
4.
Click Next.
5.
Click
Finish to restart the computer.
“Bluetooth Configuration in Windows 8” on page 7 - 29
for configuration instructions.
Intel Bluetooth Combo Driver Installation
1.
Make sure the system is not in Airplane Mode, and then insert the Device
Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
2.Install Combo BT Driver > Yes.
4.
Click Next > Next.
5.
Click in the tickbox to accept the license and click Next.
6.
Click Next > Finish.
“Bluetooth Configuration in Windows 8” on page 7 - 29
for configuration instructions.
7 - 28 Bluetooth & WLAN Combo Module
Modules
Bluetooth Configuration in Windows 8
You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (i.e. not in Airplane Mode) before configuration begins.
Desktop Mode
1.
Switch to the Windows Desktop (click the App or use the Windows logo key +
D key combination).
2.
Click the notification area of the taskbar and double-click the Bluetooth icon (or click and select Show Bluetooth Devices).
3.
The Devices item in PC Settings will appear.
OR
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click Change PC Settings.
3.
The Devices item in PC Settings will appear.
\
Figure 7 - 20
Bluetooth Taskbar
Icon & Change PC
Settings (Charms
Bar -Settings)
7
Bluetooth & WLAN Combo Module 7 - 29
Modules
4.
Click Add a Device.
5.
Double-click the device you want to pair with the computer.
Figure 7 - 21
PC Settings
(Devices)
Add A Device
7
6.
On first connection the computer will provide you with a pairing code to be entered onto the device.
Figure 7 - 22
Enter the Passcode
7.
Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
7 - 30 Bluetooth & WLAN Combo Module
8.
You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft.
Modules
Figure 7 - 23
PC Settings
(Wireless)
7
Bluetooth & WLAN Combo Module 7 - 31
Modules
7
Figure 7 - 24
Bluetooth Settings
To Make your Computer Discoverable to Bluetooth Devices
1.
Switch to the Windows Desktop (click the app or use the Windows logo key +
D key combination).
2.
Click the notification area of the taskbar, click the Bluetooth icon and click
Open Settings.
3.
Click Options, and make sure that Allow Bluetooth devices to find this
computer check box (Discovery) has a tick inside it.
4.
Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a tick inside it, if you want to be notified when a
Bluetooth device wants to connect.
7 - 32 Bluetooth & WLAN Combo Module
Modules
Sound Blaster Cinema EQ
Install the Sound Blaster Cinema EQ to allow you to configure the audio settings to your requirements for the best performance in games, music and movies.
Sound Blaster Cinema EQ Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3. Click 3.Install SB Cinema EQ > Yes.
4. Choose the setup language and click Next.
5. Click Yes to accept the license.
6. Click Next > Full Installation (button).
7. Click Next > Finish to restart the computer.
Sound Blaster Cinema EQ Activation
On the first run of Sound Blaster Cinema EQ you will may to activate the application.
1.
To activate the application you will need to be connected to the internet.
2.
Double-click the Activate icon on the desktop and click the Activate button.
3.
The program will connect to the internet to verify the activation key.
4.
Click Finish to complete the application activation.
5.
Restart the computer after the process is complete.
Creative Software
AutoUpdate
Run the application from the shortcut in the Start screen and make sure you are connected to the internet, then click
Next and follow the on screen instructions to update the software.
7
Sound Blaster Cinema EQ 7 - 33
7
Modules
Sound Blaster
Cinema & HDMI
Note that the Sound
Blaster Cinema audio effects do not apply to audio generated through an HDMI connection.
Sound Blaster Cinema Application
Run the Sound Blaster Cinema control panel from the notification area of the taskbar (or from the item in the Start menu). Click on the tabs to access the any of the control panel menus.
Power On/Off
Figure 7 - 25
Sound Blaster
Cinema
(Taskbar
Notification Area
Icon & Menu)
7 - 34 Sound Blaster Cinema EQ
Modules
Sound Blaster Cinema Settings
Sound Blaster Cinema selects the built-in speakers by default and this setting may cause some sound quality issues when using headphones. To adjust the settings for
headphones do the following:
1.
Run the Sound Blaster Cinema application.
2.
Select Settings from the menu.
3.
Select Headphones from the drop-down menu (you can adjust the slider for crossover frequency).
4.
Click OK and close the application.
Settings
Figure 7 - 26
Sound Blaster Cinema
Select Headphones
7
Sound Blaster Cinema EQ 7 - 35
7
Modules
Settings
You can use the drop down menu to use presets for Music, Movie or
Games. Alternatively you can use a Custom setting.
Sound Blaster Cinema Controls
Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels.
Menu
Figure 7 - 27
Sound Blaster
Cinema Controls
• Surround: Provides virtual sound channels to control the level of immersion.
• Crystalizer: Enhances audio to make it sound livelier.
• Bass: Enhances the bass level of the sound system.
• Smart Volume: Minimizes sudden volume changes to avoid the need for constant adjustment.
• Dialog Plus: Enhances dialogue levels for movies etc.
7 - 36 Sound Blaster Cinema EQ
Modules
Sound Blaster Cinema & HDMI
1.
When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema controls will be disabled.
2.
A warning box will pop-up and will prompt “...Do you want to select another
audio device now?”.
3.
Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display).
Menu
Figure 7 - 28
Sound Blaster
Cinema HDMI
Display Warning
7
Sound Blaster Cinema EQ 7 - 37
7
Modules
Intel
®
Rapid Storage Technology
The Intel Rapid Storage Technology application provides high-performance
SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology
application (after installing all necessary drivers in the correct order) to support your RAID (if you have two mSATA SSDs installed) system or SATA drive if set
up in AHCI mode in the BIOS (see
“SATA Mode (Advanced Menu)” on page 5 -
See
“Intel® Smart Response Technology” on page 7 - 43
on setting up Smart Response.
IRST Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3.
Click 4.Install IRST Driver > Yes.
4. Click Next.
5. Click the tickbox to accept the license and click Next.
6. Click Next > Next > Next.
7. Click Finish to restart the computer.
See the following pages for more information if you have set your hard disks up in a RAID configuration.
7 - 38 Intel® Rapid Storage Technology
Modules
Intel® Rapid Storage Technology for RAID Systems
Intel® Rapid Storage Technology application displays status information on your
RAID configuration. Run the Intel® Rapid Storage Technology application from the item in the Start menu.
When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system. Various volume creation and management options are available depending on the system’s status.
Figure 7 - 29
Intel
®
Rapid
Storage Technology
Status
7
Intel® Rapid Storage Technology 7 - 39
7
Modules
Help
Click the Help (or press
F1) menu button at the top of the Intel® Rapid
Storage Technology
application.
Click Contents to view the general list of subjects covered, click In-
dex or Search for a more specific help topics on a particular item.
Click More help on this
page at the bottom of any page for page specific help.
Figure 7 - 30
Intel
®
Rapid
Storage
Technology
Help
Intel® Rapid Storage Technology Help
If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the
Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes.
7 - 40 Intel® Rapid Storage Technology
Modules
RAID Volume Data Verification and Repair
The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level:
RAID
Level
Verify Verify & Repair
RAID 0
RAID 1
Bad blocks are identified.
Bad blocks are identified.
Data on the mirrored drive is compared to data on the source drive.
N/A
Bad blocks are reassigned.
If the data on the mirrored drive does not match the data on the source drive, the data on the mirrored drive is overwritten by the data on the source.
Replacing and Reverting Recovery and Master Volumes
If a master or recovery drive fails you will need to add a new identical drive and rebuild the recovery volume to the drive. You can also revert the master drive to the state of the previous volume update. For details on how to do this see the help file
“Intel® Rapid Storage Technology Help” on page 7 - 40
.
See over for details on how to verify and repair RAID volume data. Verification will identify and repair data inconsistencies on the volume.
Table 7 - 2
RAID Level
Verification &
Repair Status
7
Intel® Rapid Storage Technology 7 - 41
Modules
Verifying and Repairing RAID Volume Data
1.
Run the Intel® Rapid Storage Technology application.
2.
Click to select the RAID in the pane on the right side of the window.
3.
Click Manage and click Advanced.
4.
Click Verify, then click Verify (button) to begin the process.
5.
The completion percentage will be listed under Status (Verifying)
6.
Click Close to complete the process.
7
Figure 7 - 31
Intel
®
Rapid
Storage
Technology
Verify
7 - 42 Intel® Rapid Storage Technology
Modules
Intel® Smart Response Technology
Intel® Smart Response Technology is an Intel® Rapid Storage Technology
(RST) caching feature that accelerates computer system performance by using the
SSD as cache memory between the hard disk drive and system memory.
System Requirements to support Intel® Smart Response Technology:
• System BIOS with SATA mode set to RAID (see “
“SATA Mode (Advanced
Menu)” on page 5 - 8
).
• Intel Rapid Storage Technology software installed.
• A Solid State Drive (SSD) with a minimum capacity of 18.6GB (or with a partition on the drive formatted to more than 18.6GB e.g a 20GB partition set on the
SSD). Note that the SSD requires at least 5MB of free unpartitioned and unallocated space (if you have used all the disk space for the partition you will need to shrink some of space for the cache memory’s use).
Figure 7 - 32
Computer
Management - Disk
Management -
Unallocated SSD
Space
See overleaf for instructions on enabling Intel® Smart Response Technology.
Intel® Rapid Storage Technology 7 - 43
7
Modules
Enabling Intel Smart Response Technology
1.
Run the Intel® Rapid Storage Technology application.
2.
Click Enable acceleration under Performance > Smart Response Technology
(note that you will at least 5MB of free unpartitioned and unallocated space on the SSD
otherwise the Smart Response Technology item will not appear).
7
Figure 7 - 33
Intel® Rapid
Storage
Technology -
Performance
Enable
Acceleration
3.
Select the SSD to be used as a cache device.
4.
Select the size from the SSD to be allocated for the cache memory (any remaining space on the SSD can be used for data storage using the simple data single-disk
RAID 0 volume that is automatically created).
7 - 44 Intel® Rapid Storage Technology
5.
Select the HDD (or RAID volume) to be accelerated (it is highly recommended that you accelerate the system volume or system disk for maximum performance).
6.
Select the acceleration mode, and then click OK (Enhanced mode is selected by default).
Note: Enhanced mode (default): Acceleration optimized for data protection.
Maximized mode: Acceleration optimized for input/output performance.
Modules
Figure 7 - 34
Enable
Acceleration
Options
7
Intel® Rapid Storage Technology 7 - 45
Modules
7.
The page will refresh and report the new configuration in under Performance >
Smart Response Technology.
7
Figure 7 - 35
Intel® Rapid
Storage
Technology -
Performance
(Smart Response
Technology)
7 - 46 Intel® Rapid Storage Technology
Intel
®
Rapid Start Technology Driver
Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to
6 seconds and can remember your computer's previous state with zero power.
System Requirements to support Intel® Rapid Start Technology:
• Rapid Start Technology should be enabled in the BIOS (see “
Start Technology (Advanced Menu)” on page 5 - 9
• Intel Rapid Storage Technology software installed.
• A Solid State Drive (SSD) with a minimum capacity of 18.6GB.
See overleaf for instructions on enabling Intel® Rapid Start Technology.
Modules
7
Intel® Rapid Start Technology Driver 7 - 47
Modules
Intel® Rapid Start Technology Configuration
1.
Enable/disable Intel(R) Rapid Start Technology from the BIOS (see
Rapid Start Technology (Advanced Menu)” on page 5 - 9
).
2.
Go the Windows control panel and double-click Administrative Tools (System
and Security)> Computer Management > Storage > Disk Management
3.
Right-click the SSD and select Shrink Volume from the menu.
7
Figure 7 - 36
Computer
Management
(Shrink SSD
Volume)
Shrink Volume
7 - 48 Intel® Rapid Start Technology Driver
Modules
4.
Enter the figure, which should be equal to amount of system memory (RAM)
in your computer, in “Enter the amount of space to shrink in MB”.
Figure 7 - 37
Shrink Volume
Size
5.
Click Shrink (any unallocated file space may be formatted for storage use).
Memory Size (Amount of Space to Shrink)
The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer. In the example above the system memory is 4GB
(1024MB * 4 = 4096GB). If you are unsure of your total system memory (RAM) then go to System control panel (System and Security) and check Installed memory (RAM). The memory size will be displayed in GB so convert by multiplying the GB figure by 1024 to get the total in MB (e.g. 8GB =
8192MB).
Intel® Rapid Start Technology Driver 7 - 49
7
Modules
6.
Run the Desktop app and right-click the lower left hot corner (or use the Windows
Logo Key + X key combination) and select Command Prompt (Admin).
Figure 7 - 38
Search for CMD
Prompt
7
Figure 7 - 39
Diskpart - List Disk
7.
Type “DISKPART”.
8.
At the DISKPART command type “list disk”.
7 - 50 Intel® Rapid Start Technology Driver
Modules
9.
Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number).
10. The message “Disk # is now the selected disk.” will appear.
Figure 7 - 40
Diskpart - Select
Disk #
11. Type “create partition primary”.
12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Figure 7 - 41
Diskpart - Create
Partition
Intel® Rapid Start Technology Driver 7 - 51
7
Modules
13. Type “detail disk”.
7
Figure 7 - 42
Diskpart - Detail
Disk
14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number).
15. The message “Volume # is now the selected volume.” will appear.
Figure 7 - 43
Diskpart - Select
Volume #
7 - 52 Intel® Rapid Start Technology Driver
Modules
16. Type the following, depending on the format of the SSD.
• For MBR formatted SSD’s: “set id=84 override” (the id must be set to 84).
• For GPT formatted SSD’s: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”.
Figure 7 - 44
Diskpart - Set id=
7
17. The message “DiskPart successfully set the partition ID.” will appear.
18. Close the CMD window.
Intel® Rapid Start Technology Driver 7 - 53
7
Modules
19. Go the Windows control panel and double-click Administrative Tools (System
and Security)> Computer Management > Storage > Disk Management.
20. The disk partition should read Healthy Hibernation Partition.
Figure 7 - 45
Computer
Management
(Healthy
Hibernation
Partition)
Healthy (Hibernation Partition)
21. Restart the computer.
22. Install the driver (see below).
Intel® Rapid Start Technology Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3.
Click 5.Install Rapid Start Driver > Yes.
4. Click Next > Next > Yes > Next > Next.
5. Click Finish to restart the computer.
7 - 54 Intel® Rapid Start Technology Driver
Modules
Intel
®
Wireless Display Application
The Intel
® Wireless Display Application (requires Intel® Centrino WLAN/
Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your
TV/external display without using HDMI or A/V cables.
Before configuring the Intel® WiDi application you will need to set up your com-
patible adapter with your display/speakers. Connect the adapter using an HDMI or
A/V cable and turn on the display (or in the case of speakers connect them to the wireless speaker adapter with the cables provided with the adapter), and then set the display to the appropriate input channel (see the documentation supplied with your
compatible adapter for full details).
Compatible
Adapters
For a list of compatible display and audio adapters check the Intel website, or your distributor/ supplier.
7
Intel® Wireless Display Application 7 - 55
7
Modules
Intel
®
WiDi Application Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3. Click 6.Install Intel WiDi AP > Yes.
4. Click Next.
5. Click the button to accept the license and click Next.
6. Click Finish.
7 - 56 Intel® Wireless Display Application
Intel
®
WiDi Application Configuration
1.
Run Intel(R) Wireless Display from the Start screen.
2.
Click I agree to the terms of this license (button).
3.
The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Modules
Figure 7 - 46
Intel
®
WiDi Scan
7
Intel® Wireless Display Application 7 - 57
Modules
\
7
Figure 7 - 47
Intel
®
WiDi Connect
& Enter Security
Code
4.
Click to select and detected adapters, and click Connect.
5.
The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter).
6.
Enter the code for the video adapter and click Continue.
7 - 58 Intel® Wireless Display Application
7.
You will then be prompted to enter a name for the video adapter and click
Continue.
8.
Click Finished to complete the setup.
Modules
Test Audio Adapter
To verify a successful audio connection (for In-
tel® Wireless Music), select the “Test your
audio connection” link or select “Finished” to bypass the test.
You can select “Play
Sample” to play an audio test sample from your adapter to the connected speaker set.
7
Figure 7 - 48
Intel
®
WiDi
Connected
Intel® Wireless Display Application 7 - 59
7
Modules
7 - 60 3G Module
3G Module
If you have included an optional UMTS/HSPDA+ based 3G Module (Universal
Mobile Telecommunications System or High Speed Packet Access) module (see
“Communication” on page D - 4
for specification details) in your purchase option,
you do not require a driver/application installation for Windows 8. Follow the instructions overleaf to install the USIM card (which will be provided by your service provider), and then use the Charms Bar Wireless icon to access the 3G network
in the same manner as the WLAN (see page
).
Important Notice
If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Important Notice - 3G & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3G module and the
Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G module is powered on, make sure that the Bluetooth/
Wireless LAN modules are powered off (use the PC Settings > Wireless control panel to
turn on/off individual modules - see
).
Modules
3G Module USIM Card Installation
Follow the instructions below to install the USIM card (which will be provided by your service provider).
1.
Turn off the computer, and turn it over.
2.
“Removing the Battery” on page 6 - 4
3.
Insert the USIM card (at the rear of the battery compartment) as illustrated below until it clicks fully into position, and replace the battery.
Power Safety
Warning
Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.
USIM Card Orientation
Note that the USIM card’s readable side (with the gold-colored contacts) should face upwards as illustrated.
7
Figure 7 - 49
USIM Card Insertion
3G Module 7 - 61
Modules
\
7
Figure 7 - 50
WiFi Settings
(Charms Bar) &
Networks (with
Mobile Broadband)
3G Configuration in Windows 8
You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins.
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
3.
A list of available access points will appear.
7 - 62 3G Module
Modules
4.
Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband.
5.
Double-click any connection icon under Mobile Broadband (or click and click
Connect).
6.
The system will connect to your network.
7.
A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session).
Figure 7 - 51
Mobile Broadband
(Connect)
7
Figure 7 - 52
Mobile Broadband
(Disconnect)
3G Module 7 - 63
7
Modules
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the system is in Airplane Mode if you are using the computer aboard aircraft.
8.
You can then access the internet, download e-mail etc. as per any internet connection.
9.
To disconnect you can select the connection and click Disconnect .
10. You need to either use Airplane Mode, or to turn the Mobile Broadband module
off aboard aircraft.
Figure 7 - 53
PC Settings
(Wireless)
7 - 64 3G Module
Modules
EM820W 3G Module PIN Code & Power-Saving
Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows 8, Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you sim-
ply do not enable a PIN for the EM820W 3G module. The following provides instructions for disabling the PIN code; for specific instructions on resolving the issue where “Insert a SIM” appears in the connection see
“Resolving the “Insert a SIM” issue with the 3G Module (Windows 8)” on page 8 - 19
.
Disabling a PIN code for a 3G Module
1.
Go to the Charms Bar.
2.
Select Settings and then click the WiFi icon.
3.
Right-click the 3G connection and select View connection properties.
Figure 7 - 54
WiFi Settings
(Charms Bar) &
Right-Click
Connection to View
Properties
EM820W 3G Module PIN Code & Power-Saving 7 - 65
7
Modules
4.
Click Security (tab) and click Disable PIN.
5.
Enter the PIN number and click Disable PIN and click OK to confirm.
6.
It is recommended that you do not Enable a PIN for the EM820W 3G module.
7
Figure 7 - 55
Disable PIN
7 - 66 EM820W 3G Module PIN Code & Power-Saving
7
Modules
7 - 67
Troubleshooting
Chapter 8: Troubleshooting
Overview
Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried.
Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative.
8
Overview 8 - 1
8
Troubleshooting
Basic Hints and Tips
Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working.
• Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip,
make sure it is actually working. Check the LED Power Indicators (see
“LED Indicators” on page 1 - 7
) to see the computer’s power status.
• Connections - Check all the cables to make sure that there are no loose connections anywhere.
• Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config-
ured in your Power Options (see
“Configuring the Power Buttons” on page 3 - 8
nation, or power button to wake-up the system.
• Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the bright-
).
• Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.
• Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive when you start up your machine (this is a common cause of the message “Invalid system disk - Replace the
disk, and then press any key” / “Remove disks or other media. Press any key to restart”).
8 - 2 Basic Hints and Tips
Troubleshooting
Backup and General Maintenance
• Always backup your important data, and keep copies of your OS and programs safe, but close to hand.
Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet.
• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so.
• Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Boot password for the SCU (see
“Security Menu” on page 5 - 12
• Keep copies of vital settings files such as network, dialup settings, mail settings etc. (even if just brief notes).
8
Warranty
The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.
Backup and General Maintenance 8 - 3
8
Troubleshooting
Viruses
• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini-
tions file updates are usually downloadable directly from the internet.
• Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e-
mail attachments so take care when opening any attached file. You can configure most Anti-Virus programs to check all e-mail attachments. Note: You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the person’s knowledge.
• Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OS’s documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one).
8 - 4 Viruses
Troubleshooting
Upgrading and Adding New Hardware/Software
• Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system.
• Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
• Read the documentation. We can assume, since you are reading this that you are looking at the computer’s manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”.
• When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected.
• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendor’s websites).
• Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs.
8
Upgrading and Adding New Hardware/Software 8 - 5
8
Troubleshooting
• Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming.
8 - 6 Upgrading and Adding New Hardware/Software
Troubleshooting
Problems and Possible Solutions
Problem Possible Cause - Solution
You turned on the power but it doesn’t work.
Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
blinking orange.
immediately, turn it off then on again.
You are losing battery power too quickly.
The system is using too much power. If your OS has a Power Options scheme
(see
) check its settings. You may also be using a
peripheral device/USB device that is drawing a lot of power.
Actual battery operating time is shorter than expected.
The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see
“Battery Information” on page 3 - 13
).
Power Options have been disabled. Go to the Control Panel in Windows and re-enable the options.
A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power.
8
Problems and Possible Solutions 8 - 7
8
Troubleshooting
Problem
The computer feels too hot.
Possible Cause - Solution
Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see
). Make sure you’re using the correct adapter.
Nothing appears on screen.
No image appears on the external
monitor I have plugged in and powered on.
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan intakes to be blocked.
The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see
“Configuring the Power Buttons” on page 3 - 8
The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If an external monitor is connected, turn it on.
The screen saver is activated. Press any key or touch the TouchPad.
You haven’t installed the video driver and configured it appropriately from the
for instructions on installing and configuring
the video driver.
8 - 8 Problems and Possible Solutions
Problem
You forget the boot password.
Troubleshooting
Possible Cause - Solution
If you forget the password, you may have to discharge the battery of the CMOS.
Contact your service representative for help.
Password Warning
If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
The sound cannot be heard or the volume
is very low.
Unwelcome numbers appear when typing.
The volume might be set too low. Check the volume control in the Volume
Control Panel in the Windows notification area, or use the key combination Fn
+ F5 and F6 (see
“Function Keys & Visual Indicators” on page 1 - 10
adjust.
Num Lock is turned ON (see
“LED Indicators” on page 1 - 7
).
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the regular keyboard may not work.
8
Problems and Possible Solutions 8 - 9
8
Troubleshooting
Problem Possible Cause - Solution
The system freezes or the screen goes dark.
The system never goes into a power
saving mode.
The Wireless LAN/Bluetooth modules cannot be detected.
The PC Camera module cannot be detected.
The Wireless LAN/Bluetooth modules cannot be configured.
The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit.
Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see
“Power-Saving States” on page 3 - 6
). Make sure you have enabled Hibernate mode from the control panel.
The modules are off as the computer is in Airplane Mode. Check the LED indicator
to see if it is in Airplane Mode (see
). Use the Fn + F11 key combination to toggle Airplane Mode on/off (see
).
The module is off. Press the Fn + F10 key combination in order to enable the module (see
“Function Keys & Visual Indicators” on page 1 - 10
). Run the camera application to view the camera picture.
The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in
“Wireless LAN Module” on page 7 - 19
and/or
“Bluetooth & WLAN Combo Module” on page 7 - 28
).
8 - 10 Problems and Possible Solutions
Troubleshooting
Problem Possible Cause - Solution
A file cannot be copied to/from a connected Bluetooth device.
I cannot obtain high speed Bluetooth data transfer.
The transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not
supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process has been completed
To obtain high speed Bluetooth data transfer take into account the following:
• To achieve high speed transfer speeds, both devices must support high
speed data transfer (i.e both the computer and the Bluetooth compatible device you are connecting to).
• Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer, and for configuration information.
The port is not powered on. Toggle power to the port using the Fn + power
button combination.
The computer is off (or in Sleep Mode) but powered by the AC/DC adapter plugged in to a working outlet, or by battery with a capacity above 20%. I have plugged a
device into the powered USB port in order to charge it, but the device is not
charging.
This function may not work with certain external USB compliant devices (check
your device’s documentation). If this is the case, power the computer on and
connect the external USB device in order to charge it.
No sound can be heard through an HDMI connected display.
Note that this function is designed to help charge USB compliant devices, but is not designed to allow their operation.
You have not configured the HDMI audio output. See
“HDMI Audio
Configuration” on page C - 26
.
8
Problems and Possible Solutions 8 - 11
8
Troubleshooting
Problem Possible Cause - Solution
The Sound Blaster audio controls don’t work when the system is connected to an
external display through an HDMI
cable.
Note that Sound Blaster Audio will be disabled when you are connecting to an external display through an HDMI connection. See
“Sound Blaster Audio &
HDMI” on page C - 28
.
8 - 12 Problems and Possible Solutions
Troubleshooting
Resolving the “Insert a SIM” issue with the 3G Module (Windows 8)
1.
If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) under Wireless in PC Settings, and the system has just resumed from a power-saving state the following error may occur.
Figure 8 - 1
- PC Settings (Charms Bar) - Wireless (Mobile Broadband Off)
2.
On resuming from the power-saving state the standard procedure would be to go to PC Settings in the Charms
Bar and turn on Mobile broadband under Wireless > Wireless Devices.
Problems and Possible Solutions 8 - 13
8
Troubleshooting
3.
Go to the Charms Bar.
4.
Select Settings and you will then note that the WiFi icon will read Unavailable.
5.
Standard procedure would be to click the connection and enter the PIN number to unlock the connection.
6.
In this instance you will note that the Mobile broadband connection will read Insert a SIM.
8
Figure 8 - 2
- Mobile Broadband (Insert a SIM)
7.
In this case you will need to restart the computer.
8.
After system restart you can then connect to the Mobile Broadband as normal.
9.
To fully resolve this issue it is recommended that you do not Enable a PIN for the EM820W 3G module.
8 - 14 Problems and Possible Solutions
Interface (Ports & Jacks)
Appendix A: Interface (Ports & Jacks)
Overview
The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) A - 1
A
A
Interface (Ports & Jacks)
Ports and Jacks
Item
Card Reader
DC-In Jack
Description
The card reader allows you to use the following digital storage cards:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
Push the card into the slot and it will appear as a removable device.
Plug the supplied AC/DC adapter into this jack to power your computer.
External Monitor Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
HDMI-Out Port
Headphone-Out Jack
The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel
Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video
“HDMI Audio Configuration” on page C - 33
).
Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack.
Microphone-In Jack Plug an external microphone in to this jack to record on your computer.
A - 2 Interface (Ports & Jacks)
Item
RJ-45 LAN Jack
Interface (Ports & Jacks)
Description
This port supports LAN (Network) functions.
Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Security Lock Slot
USB 2.0/1.1 Ports
USB 3.0 Port
3.
0
Powered USB 3.0 Port
3.
0
To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
The USB 3.0 ports are denoted by their blue color (and is not operational under DOS); USB 2.0
ports are colored black. USB 3.0 will transfer data much faster than USB 2.0, and is backwardscompatible with USB 2.0.
Note:
The powered USB 3.0 port (see
Figure 1 - 13 on page 1 - 23
) may be toggled on /off by means of the Fn + Power Button key combination. When the powered USB port is on it will supply power (for charging devices only, not for operating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices - see page
8 - 12
).
Note: This function is designed to help charge USB compliant devices, but is not designed to
allow their operation.
Interface (Ports & Jacks) A - 3
A
Interface (Ports & Jacks)
A
A - 4
Control Center
Appendix B: Control Center
Overview
The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected. The Control Center in Windows 8 works under the Desktop app and not under the Start screen.
Figure B - 1 - Control Center
Control Center B - 1
B
B
Control Center
Power Modes
You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc.
You can click a Control Center icon to set an overall power mode and then click individual icons in the
Control Center to power on/off the Touchpad and PC camera.
Modes
Power
Saving
Entertainment Quiet Performance
User
Defined
Icon
Power Plan
Power Conservation
Mode
Brightness
Power Saver
Energy Star
10
OFF PC Camera
TouchPad ON
Power Saving Power Saving
Energy Star Energy Star
High
Performance
Performance
100
OFF
ON
40
ON
ON
100
ON
ON
Table B - 1- Power Modes
B - 2 Control Center
Control Center
Power Status
The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state.
Brightness
The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight
(press any key to turn it on again). Note that screen brightness is also effected by the Power Mode selected (see
Volume
The Volume icon will show the current volume level. You can use the slider to adjust the Volume or the Fn +
F5/F6 key combinations, or use the Fn+ F3 key combination to mute the volume.
Power Conservation
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into
a low-power sleep modes after a designated period of inactivity (see
“Power Conservation Modes” on page 3 -
). Click either the Performance, Balanced or Energy Star button.
B
Control Center B - 3
B
Control Center
Sleep
Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the
computer enter the appropriate power-saving mode (see
“Power-Saving States” on page 3 - 6
Display Switch
Click the Display Switch button to access the menu (or use the + P key combination) and select the appro-
priate attached display mode (see page
).
Time Zone
Clicking the Time Zone button will access the Date and Time Windows control panel.
Desktop Background
Clicking the Desktop Background button will allow you to change the desktop background picture.
TouchPad/PC Camera
Click either of these buttons to toggle the TouchPad or camera module’s power status. A crossed out icon will appear over the top left of the icon when it is off
.
Note that the power status of the camera module is also
effected by the Power Mode selected (see
Caps Lock/Scroll Lock/ Number Lock
Click the button to toggle the appropriate lock mode.
B - 4 Control Center
Appendix C: Video Driver Controls
The basic settings for configuring the LCD are outlined in
“Video Features” on page 1 - 26
.
Video Driver Installation
Make sure you install the drivers in the order indicated in
Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers
(button).
Video (VGA)
1.
Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
NVIDIA Video (VGA)
1.
Click 3.Install NVIDIA VGA Driver > Yes.
2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement.
3. Click Next.
4. Click Close to complete the installation.
Video Driver Controls
Video Card Options
Note that card types, specifications and drivers are subject to continual updates and changes. Check with your distributor/supplier for the latest details on video cards supported
(see
).
C
Video Driver Installation C - 1
C
Video Driver Controls
iGPU or dGPU
Note the NVIDIA control panel refers to High-
performance NVIDIA
processor (which is the discrete GPU) and Inte-
grated graphics (which is the integrated GPU).
NVIDIA
®
Optimus
™
Technology
Most notebook computers come with either a discrete or integrated graphics solution.
Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications. However computers with discrete graphics solutions tend to be heavy in power consumption, and slightly larger in size in order to incorporate the dedicated discrete GPU.
Integrated graphics solutions usually feature memory sharing technology to help save power consumption and allow for longer battery life. However computers with integrated graphics solutions will not usually run games, HD video or GPU-based applications without severe limitations.
Nvidia
®
Optimus
™
technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. Thus when an application is run that requires extra performance or quality, then the system will run the discrete GPU (dGPU); when the system does not require such enhanced performance it will let the integrated (iGPU) handle it.
C - 2 NVIDIA® Optimus™ Technology
How Optimus Technology works
When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required.
UMA Mode & Performance
UMA Mode is designed for maximum power saving, however this does have an affect on the system’s overall video performance (as it is based on the Power saver power plan).
Video Driver Controls
Customization
Options
Although Optimus is completely seamless to the user, NVIDIA also allow customization options within the control panel (see
Customization Options” on page C - 28
If you require better video performance then it is recommended that you use Optimus
Mode. Alternatively you may switch the UMA Mode power plan to Balanced (however power savings will be reduced in this case).
Note that when the power plan is set to UMA Mode the GPU LED indicators may no longer display the correct status.
C
NVIDIA® Optimus™ Technology C - 3
Video Driver Controls
Intel® Dynamic Video Memory Technology
Intel
®
DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver
must be installed). DVMT returns whatever memory is no longer needed to the operating system.
C
C - 4 Intel® Dynamic Video Memory Technology
Intel
®
Graphics & Media Control Panel
Advanced video configuration options are provided by the Intel
®
HD Graphics
Control Panel. To access the control panel see below and overleaf:
1.
Click the Intel® Graphics and Media Control Panel icon in the Start screen.
Video Driver Controls
(see over)
Figure C - 1
Start Screen
Intel® G&M Control
Panel
Intel® Graphics & Media Control Panel C - 5
C
Video Driver Controls
OR
2.
Right-click the Desktop and select Graphics Properties from the menu.
OR
3.
Click Advanced settings in the Screen Resolution control panel in Windows.
4.
Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties
(button).
5.
Double-click the Intel(R) HD Graphics control panel in the Windows Control
Panel.
Figure C - 2
Intel® HD Graphics
Control Panel
C
C - 6 Intel® Graphics & Media Control Panel
You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right.
Video Driver Controls
Figure C - 3
Intel® HD Graphics
Control Panel
Intel® Graphics & Media Control Panel C - 7
C
Video Driver Controls
Sub-Menus
Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Figure C - 4
Intel® HD Graphics
Control Panel
Sub-Menus
C
C - 8 Intel® Graphics & Media Control Panel
Display
Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays.
Video Driver Controls
Multiple Display
At least one other display must be attached in order to view multiple display selection options.
Figure C - 5
Intel® HD Graphics
Control Panel
Display Settings
Intel® Graphics & Media Control Panel C - 9
C
Video Driver Controls
Multiple Display
At least one other display must be attached in order to view multiple display selection options.
Click the Display menu at the top of the screen to display the sub-menus. The Mul-
tiple Displays menu allows you to configure the display mode of any attached dis-
“Attaching Other Displays” on page C - 21
).
Figure C - 6
Intel® HD Graphics
Control Panel
Display Settings -
Multiple Displays
C
C - 10 Intel® Graphics & Media Control Panel
The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio
Without Video to keep audio on when the display blanks out for power saving purposes.
Video Driver Controls
Figure C - 7
Intel® HD Graphics
Control Panel
Display Settings -
Audio
Intel® Graphics & Media Control Panel C - 11
C
Video Driver Controls
3D
This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and
Custom allows you to configure the Anisotropic Filtering, Vertical Sync and
Anti-Aliasing features to your preferences. Click Apply to save changes.
Figure C - 8
Intel® HD Graphics
Control Panel 3D
C
C - 12 Intel® Graphics & Media Control Panel
Options
Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Video Driver Controls
Figure C - 9
Intel® HD Graphics
Control Panel
Options
Intel® Graphics & Media Control Panel C - 13
C
Video Driver Controls
Preferences
Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD
Graphics Control Panel.
Make sure you turn Tray
Icon On to display the
Intel® HD Graphics
Control Panel icon in the notification area of the taskbar (as below).
Click the Options menu at the top of the screen to display the sub-menus. The In-
formation Center provides details on System Information, the Built-In Display and any attached displays.
C
Figure C - 10
Intel® HD Graphics
Control Panel
Options -
Information Center
C - 14 Intel® Graphics & Media Control Panel
Video
The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings based on the Ap-
plication Settings or Driver Settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes.
Video Driver Controls
Figure C - 11
Intel® HD Graphics
Control Panel Video
(Basic - Driver
Settings)
Intel® Graphics & Media Control Panel C - 15
C
Video Driver Controls
Click the Video menu at the top of the screen to display the sub-menus.The Image
Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhance-
ment, Noise Reduction etc.Click Apply to save changes.
Figure C - 12
Intel® HD Graphics
Control Panel Video
Image
Enhancement Basic
C
C - 16 Intel® Graphics & Media Control Panel
The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Video Driver Controls
Figure C - 13
Intel® HD Graphics
Control Panel Video
Image Scaling &
Gamut Mapping
Intel® Graphics & Media Control Panel C - 17
C
Video Driver Controls
Power
Choose a Power Plan for when the computer is Plugged in or On battery. When turned on, the Display Power Saving Technology (which adjusts the backlight intensity) battery settings may be adjusted by means of the slider towards Maximum
Quality or Maximum Battery. Click on Apply to save changes.
Figure C - 14
Intel® HD Graphics
Control Panel Power
(Battery Settings)
C
C - 18 Intel® Graphics & Media Control Panel
Support
Click Support and select an item from the menus to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links.
Video Driver Controls
Figure C - 15
Intel® HD Graphics
Control Panel
Support
Intel® Graphics & Media Control Panel C - 19
C
C
Video Driver Controls
Display Devices & Options
Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported.
Attaching Displays
When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R)
HD Graphics Control Panel to configure the full screen display.
Table C - 1
Display Modes
Display Mode
(Intel / Win8)
Single Display
Clone/Duplicate
Extended / Extend
Description
One of the connected displays is used as the display device
(PC screen only or Second screen only).
Both connected displays output the same view and may be configured independently
Both connected displays are treated as separate devices, and act as a virtual desktop
C - 20 Display Devices & Options
Attaching Other Displays
To Clone Displays:
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3.
Click Clone from the Select Multiple Display Mode menu.
4.
Click Apply, and OK to confirm the settings change.
5.
You can select the displays to be used from the Select Active Displays menu.
Video Driver Controls
Multiple Display
At least one other display must be attached in order to view Multiple
Display selection options.
Figure C - 16
Display > Multiple
Displays (Clone)
Attaching Other Displays C - 21
C
C
Video Driver Controls
Display Settings
Extended Desktop
You can have different
Colors, Screen Area and Monitor Refresh
Rates for each display device provided your
monitor can support
them.
You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays.
To Enable Extended Mode:
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3.
Click Extended from the Select Multiple Display Mode menu.
4.
Click Apply, and OK to confirm the settings change.
Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display).
Figure C - 17
Display > Multiple
Displays (Extended)
Click Display Set-
tings to make any adjustments required.
C - 22 Attaching Other Displays
Attaching Other Displays - Devices (Charms Bar)
You can configure attached displays from Devices (in the Windows 8 Charms Bar)
.
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go the Charms Bar and select Devices.
3.
Click Second Screen.
4.
Click on any one of the options from the menu to select Duplicate, Extend or a
Single (PC Screen only or Second Screen only) display.
Video Driver Controls
Windows Logo Key
+ P Key
Combination
You can use the
+ P
key combination to quickly bring up the Sec-
ond Screen menu.
You can also use the
Display Switch
button in the Control Cen-
ter to access the menu and select the appropriate attached display mode.
You can also use the Fn
+F7 key combination to quickly access the Sec-
ond Screen menu in
Windows 8.
Figure C - 18
Second Screen
(Devices)
Attaching Other Displays - Devices (Charms Bar) C - 23
C
Video Driver Controls
Configuring an External Display In Windows
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go to the Screen resolution control panel (see page
1 - 32
) in the Desktop app.
3.
Click the Detect button.
4.
The computer will then detect any attached displays.
C
Figure C - 19
Screen Resolution
Multiple Displays
C - 24 Attaching Other Displays - Devices (Charms Bar)
5.
You can configure the displays from the Multiple Displays menu.
Video Driver Controls
Figure C - 20
Screen Resolution
Multiple Display
Options
• Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s)
• Extend these displays - Treats both connected displays as separate devices
• Show desktop only on 1/2 - Only one of your displays is used.
Attaching Other Displays - Devices (Charms Bar) C - 25
C
Video Driver Controls
NVIDIA Control
Panel
To access the Ge-
Force..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control
Panel.
NVIDIA Control Panel
More advanced video configuration options are provided in the NVIDIA Control
Panel tab.
1.
Go to the Control Panel.
2.
Double-click NVIDIA Control Panel (click to view the control panel in either Large
icons or Small icons if you are in Category view).
C
Figure C - 21
NVIDIA Control
Panel
C - 26 NVIDIA Control Panel
The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and video configuration.
Video Driver Controls
Navigating the
Control Panel
Navigate through the control panels in much the same way as you would a web page.
Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
Figure C - 22
NVIDIA Control
Panel
C
NVIDIA Control Panel C - 27
Video Driver Controls
Display GPU
Activity Icon
Click to enable Dis-
play GPU Activity
Icon in the Notifica-
tion Area to quickly access the GPU Activity monitor from the taskbar.
Optimus
™
Customization Options
One of the most important aspects of Nvidia
®
Optimus
™
technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, and does not require any input from the user. However customization options are offered for users who prefer to set their own parameters for GPU usage.
Context Menu
One of the quickest ways to choose which GPU to use for a particular application is by using the “Run with graphics processor” in the context menu.
1.
Go to the NVIDIA Control Panel (see page
).
2.
Click Desktop from the top menu and select Add “Run with graphics
processor” to Context Menu (it should have a tick alongside it).
C
Figure C - 23
NVIDIA Control
Panel - Desktop
C - 28 Optimus™ Customization Options
3.
Close the NVIDIA Control Panel.
4.
Find the executable file icon of the application you want to run.
5.
Right-click the icon and select Run with graphics processor from the context menu.
6.
Select either High-performance NVIDIA processor (dGPU) or Integrated
graphics (iGPU) to run the program with the selected GPU.
Video Driver Controls
iGPU or dGPU
Note the NVIDIA control panel refers to
High-performance
NVIDIA processor
(which is the discrete
GPU) and Integrated
graphics (which is the integrated GPU).
Figure C - 24
Context Menu with
Run with graphics processor
C
Right-click the application executable file
Optimus™ Customization Options C - 29
Video Driver Controls
Global Settings
Global settings allows you to set the preferred graphics processor for overall use.
Ideally this would be the iGPU for battery life, but this can be set to the dGPU if preferred.
1.
Go to the NVIDIA Control Panel (see page
).
2.
Click Manage 3D Settings (3D Settings) and select Global Settings (tab).
3.
Select either Integrated graphics (iGPU) or High performance NVIDIA
Processor (dGPU) from the drop-down menu.
4.
Click the Setting menu items to select any options required.
5.
Click Apply to save the settings.
Figure C - 25
Global Settings
C
C - 30 Optimus™ Customization Options
Program Settings
Program settings allows you to make specific adjustments for installed applications.
1.
Run the NVIDIA Control Panel (see page
).
2.
Click Manage 3D Settings (3D Settings) and select Program Settings (tab).
3.
Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu.
4.
Select the preferred graphics processor for the program from the drop-down menu.
5.
Click the Setting menu items to select any options required.
6.
Click Apply to save the settings.
Video Driver Controls
Figure C - 26
Program Settings
Optimus™ Customization Options C - 31
C
Video Driver Controls
Set PhysX
®
Configuration
NVIDIA
®
PhysX
®
is a physics engine that can use the GPU to accelerate game and
3D application performance. You can select the GeForce video card or CPU as a
PhysX
®
processor, or configure the computer to auto-select a PhysX
®
processor
(recommended default setting).
1.
Go to NVIDIA Control Panel (see page
2.
Click Set PhysX configuration.
3.
Click to Select a PhysX processor from the menu; Auto-select (recommended) is the default setting.
4.
Click Apply to save the settings.
Figure C - 27
Set PhysX
®
Configuration
C
C - 32 Set PhysX® Configuration
HDMI Audio Configuration
HDMI (High-Definition Multimedia Interface) carries both audio and video signals.
In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below.
1.
Go to the Control Panel.
2.
Click Sound (Hardware and Sound) and click Playback (tab)
3.
Depending on your display, the playback device may be selected, however in some cases you may need to select the audio device and click Set Default (button).
4.
Double-click the device to access the control panel tabs illustrated overleaf.
Video Driver Controls
Volume Adjustment
The sound volume level can be set using the volume control in the Set-
tings
menu in the
Charms Bar.
Figure C - 28
Sound - HDMI
Device (set Default)
HDMI Audio Configuration C - 33
C
Video Driver Controls
5.
Adjust the HDMI settings from the control panel tabs.
6.
Click OK to close the Sound control panel.
Figure C - 29
HDMI Device
Properties
C
C - 34 HDMI Audio Configuration
HDMI Notes
• Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
• To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual).
HDMI Video Configuration
1.
Connect an HDMI cable from the HDMI-Out port to your external display.
2.
Configure your external display as per the instructions in
3.
Set up your external display (TV or LCD) for HDMI input (see your display device manual).
4.
You can now play video/audio sources through your external display.
Sound Blaster Cinema EQ & HDMI
1.
When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema EQ controls will be disabled.
2.
A warning box will pop-up and will prompt “...Do you want to select another
audio device now?”.
3.
Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display.
Video Driver Controls
Other Applications
If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration
(the application must support digital to analog translation).
C
HDMI Audio Configuration C - 35
Video Driver Controls
C
C - 36
Specifications
Appendix D: Specifications
Latest Specification Information
The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications D - 1
D
D
Specifications
Processor
Intel® Core i7-4900MQ (2.8GHz)
Mobile Processor
8M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 47W
Intel® Core i7-4800MQ (2.7GHz)
Mobile Processor
6M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 47W
Intel® Core i7-4700MQ (2.4GHz)
Mobile Processor
6M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 47W
Core Logic
Mobile Intel® HM87 Lynx Point Express
Chipset
Display
13.3" (33.78cm) HD+ (1600 * 900), 16:9,
2.85 - 3.1mm Thick Backlit Panel
13.3" (33.78cm) FHD (1920 * 1080),
16:9, 2.8mm Thick Backlit Panel
Memory
Dual Channel DDR3L
*Three 204 Pin SO-DIMM Sockets
Supporting DDR3L 1600 MHz Memory
Modules (real operational frequency
depends on the FSB of the processor)
Memory Expandable up to 16GB
Compatible with 2GB, 4GB or 8GB Modules
Video Adapter Options
Intel® Integrated GPU and NVIDIA®
GeForce Video:
Supports NVIDIA® Optimus
Switchable GPU Technology between iGPU and dGPU
Intel® HD Graphics (GPU Type
Depends on Processor)
Dynamic Frequency
Intel® Dynamic Video Memory
Technology Supporting Shared Memory up to 1.7GB
Supports Microsoft DirectX ® 11.1
nVIDIA® GeForce GTX 765M PCIe * 8
Video Chip
2GB GDDR5 Video RAM On Board
Supports Microsoft DirectX
®
11.1
NVIDIA PhysX™
GeForce CUDA™ Technology
NVIDIA® Optimus™ Technology
Storage
One Changeable 2.5", 9.5 mm (h) SATA
(Serial) Hard Diskport mSATA SSD (RAID 0/1) with SATA
Interface
Audio
High Definition Audio
Built-In Microphone
2 Built-In Speakers
Sound Blaster™ Cinema
Keyboard & Pointing Device
Isolated Illuminated Keyboard
Built-In TouchPad (with Multi Gesture and
Scrolling Functionality)
D - 2 Specifications
Interface
One USB 2.0 Port
Three USB 3.0 Ports (Including one AC/
DC Powered USB 3.0 Port)
One HDMI™-Out (High-Definition
Multimedia Interface) Port (with HDCP)
One External Monitor Port
One Microphone-In Jack
One Headphone/Speaker-Out Jack
One RJ-45 LAN Jack
One DC-In Jack
Card Reader
Embedded Multi-In-1 Push-Push Card
Reader
- MMC / RSMMC
- SD / Mini SD / SDHC / SDXC
Note: Some of these cards require PC adapters that are usually supplied with the cards.
Specifications
Slots
Three Mini-Card Slots:
Slot 1 for Half Size Mini-Card WLAN
Combo Module with PCIe & USB
Interfaces:
Slot 2 for Full Size Mini-Card mSATA
SSD (Solid State Drive) with SATA
Interface)
Slot 3 for Full Size Mini-Card mSATA
SSD (Solid State Drive) with SATA
Interface) OR Full Size Mini-Card 3G
Module with USB Interface (Factory
Option)
Communication
Built-In 10/100/1000Mb Base-TX Ethernet
LAN
2.0M HD PC Video Camera Module
Intel® Dual Band Wireless-N 7260 (2*2
802.11 a/g/n) Half Mini-Card PCIe WLAN
+ Bluetooth Combo Module (Factory
Option)
Intel® Wireless-N 7260 (2*2 802.11 b/g/n)
Half Mini-Card PCIe WLAN
+
Bluetooth
Combo Module (Factory Option)
Intel® Dual Band Wireless-AC 7260
(2*2 802.11 a/c) Half Mini-Card PCIe WLAN
+ Bluetooth Combo Module (Factory Op-
tion)
(802.11b/g/n) Half Mini-Card PCIe WLAN
+ Bluetooth V4.0+LE Combo Module
(Factory Option)
(802.11b/g/n) Half Mini-Card PCIe WLAN
Module (Factory Option)
UMTS/HSPA+ based 3G Module with
Full Size Mini-Card Interface (Factory
Option)
Quad-band GSM/GPRS (850 MHz, 900
MHz, 1800 MHz, 1900 MHz)
UMTS WCDMA FDD (2100 MHz)
Note that UMTS modes CAN NOT be used in North America
BIOS
One 48Mb SPI Flash ROM
AMI BIOS
Security
Security (Kensington® Type) Lock Slot
BIOS Password
Specifications D - 3
D
Specifications
Operating System
Windows® 8
Features
Painted Style for some designs
Intel® Anti-Theft Technology
Intel® Rapid Start Technology
Intel® Smart Response Technology
Indicators
LED Indicators - Power/Suspend,
Battery, HDD, Airplane Mode, Num Lock,
Caps Lock, Scroll Lock, Camera
Power
Full Range AC/DC Adapter – AC in 100 -
240V, 50 - 60Hz DC Output 19.5V, 6.15A
(120 Watts)
Removable 6 Cell Smart Lithium Ion Battery
Pack 62.16WH
Power Management
Supports Wake on LAN
Supports Wake on USB
Supports Wake on RTC Alarm (AC Mode
Only
Environmental Spec
Temperature
Operating: 5
°
C - 35
°
C
Non-Operating: -20°C 60°C
Relative Humidity
Physical Dimensions & Weight
330mm (w) * 227mm (d) * 31.9mm (h)
2.0kg with Battery
D
D - 4 Specifications
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement