ONE PRO Instructions_913
- Model #ONE-PRO
Power Extension Cable Management
Power + Cable Kit
Kit Includes:
Tools for Installation
Not Included
PowerOutlet | PowerInlet | 72” PowerConnect Supply Cord | Template
Stud Finder
Level
Drywall Saw
Flat-Blade
CODE COMPLIANCY
Wall Cut-out Template:
Lay against wall, use a level on edge
of paper to align.
Use a pencil to trace around edge.
Use drywall saw or sharp utility
knife cut on the edge of the line.
Remove drywall section.
SUPPORT
Meets all US states and cities
1)NEC Article 334.30
adaptive to the National
Electrical Code (NEC)
Unsupported NM Cable
2.1/4” x 3.5/8”
57mm x 93mm
allowing NM type building cable.
2) NEC 2014 Article 400.7(A)(11)
Specific locations not allowing
Permitted use of cord / approved kit
NM-type building cable:
using inlet to energize receptacle
~Cook County, IL ~NYC, NY
Model #ONE/Pro
PowerIN
PowerOUT
!
Caution - Risk of Fire - Do Not Install Power Supply Cord Within the Wall Cavity
WARNING - Risk of Fire and Shock, Do Not Connect this Box to any Other Circuits or Outlets.
This kit is rated to 15AMP 125Volt use only
Do not install this product near water, example, near a sink, tub, shower, swimming pool or laundry area.
Manufacturer is not liable for damages due to improper installation methods not followed herein.
This product does not have built-in electronic circuitry for surge protection or A/C filtering.
It is recommended that this product be connected to a quality surge-protector/power conditioner for equipment protection.
Disclaimer. HD-Products, Inc. the Manufacturer, it's agents, suppliers, and affiliates, shall not be liable for any damages, not limited to; misuse, acts of nature,
verbal and written expression and improper installation. Improper installation is determined such to include, not limited to, non-code compliant installation, product
modifications, alterations, adjustments, and substitutions of components or materials.
Limited 2-year Warranty from Manufactures Defects: Limited Two Year product warranty against manufacturer's defects.
HD-Products, Inc., intent to make this manual accurate and complete. However, HD-Products, Inc., makes no claim that the information contained herein covers all details, conditions, or
variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change
without notice or obligation of any kind. HD-Products, Inc., makes no representation of warranty, expressed or implied, regarding the information contained herein.
HD-Products, Inc/LLC. PowerBridge Solution 3869 Norwood Dr. Littleton, CO 80125 USA
Customer Service: 855-755-9838 [email protected] www.PowerBridge1.com
Part No. ONECK913
Step 1
2013 All Rights Reserved
Location - Wall Cutout
PowerOUT - Determine TV wall mount bracket location.
Align between wall framing studs.
Use stud finder to determine in-wall obstructions between
framing both VERTICALLY and HORIZONTALLY.
Install in any direction, right/left, horizontal or vertical below,
above, next to TV wall bracket.
PowerIN - Install within 60” from an existing power outlet or
power-surge device.
Patent Pending
!
PowerOUT
PowerBridge can only be installed
within standard construction walls.
Vertical
or Horizontal
Only attempt installation within
2x4 or 2x6 wood/metal stud
framed wall.
Do not exceed more
than 60” apart from
existing outlet or
surge-protection unit
PowerIN
Use supplied template sheet to mark area to cut out from drywall.
Use a level to maintain proper alignment.
Carefully use drywall saw or utility knife to cut along outside of line.
LEVEL
!
If insulation exists,
remove or push
completely away
from the openings
to allow proper
flush mounting.
Step 2 In-Wall Installation
A) Begin at the upper PowerOUT location.
Drop or wall-fish audio video cables and NM-type
PowerWire (ROMEX) to the PowerIN location below.
Pull all cables out lower cutout.
!
Use NM-type building wire.
14/2 size wire only.
Copper wire only CU
Wire Connection - Assembly
B) Strip NM-type PowerWire use Wire Strip Gauge on label.
Remove 1.5” of outer sheath. ½” off Black and White wires.
C) Insert wire through funnel of back-box as shown.
D) Insert wires as shown on label into back of OUTLET/INLET.
E) Tighten all three screws, tug on wires, make certain all secure.
F) Bend all three wires toward the cable-brush.
G) Slide back-box onto back, secure with the 4 supplied screws.
H) Insert tab into funnel, this snaps in place.
TOP
OUTLET
INLET
< Silver Screw
WHITE Wire
Green Screw
BARE Wire
Green Screw
BARE Wire
W
D
C
W
Brass Screw >
BLACK Wire
Silver Screw >
WHITE Wire
B
E
F
G
H
TOP
< Brass Screw
BLACK Wire
G
I) Slide audio video cables through backside through CableBrush.
Allow for enough cable length out to connect to TV and Equipment.
J) Slide both wall plates into wall opening.
Use Flat-Blade screw driver to secure panel to wall.
Careful to not over-tighten.
Step 3 Plug it in
Plug supplied 6’ PowerConnect cord into PowerIN.
Plug other end into existing grounded outlet or surge protector.
CAUTION-Risk of Fire-Only Use Cord Set Provided With This Kit
or equivalent.
The PowerBridge In-Wall Extension is now energized.
Plug TV power supply cord in to PowerOUT and connect AV cables to TV.
Follow wall mount manufacture instructions, install TV on wall bracket.
Plug in TV
Surge Protector
Existing
Outlet
Plug in Flat Angle Plug
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement