ACTiSYS | ACT-IR200L | User's Manual | ACTiSYS ACT-IR200L User's Manual

ACTiSYS ACT-IR200L User's Manual
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
ACT-IR220L+/220L/200L
IrDA PC Adapter
User’s Manual
ACTiSYS Corp.
48511 Warm Springs Blvd, Suite 206
Fremont, CA 94539, USA
TEL: (510) 490-8024, FAX: (510) 623-7268
E-Mail: irda-support@actisys.com
Web: www.actisys.com
Release 1.5
ACTiSYS Corporation 2001
1
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
FCC & VCCI Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING-FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user authority to operate
this equipment
NOTE: This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Increase the separation between the equipment and receiver.
-Reorient or relocate the receiving antenna.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for helps.
This equipment is in the 2nd Class category (information equipment to be used in a residential
area there to) and conforms to the standards set by the Voluntary Control Council For
Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing
radio interference in such residential area.
When used near a radio or TV receiver, it may become the cause of radio interference. Read the
instructions for correct handling.
NOTE: Must be used with shielded cable only.
FOR YOU RECORDS
For your assistance in reporting this product in case of loss or theft, please record the model and
serial number that is located on the bottom of the case. Please retain this information.
Model Number
Serial Number
Date of Purchase
Place of Purchase
All indicated copyrights and trademarks in the following pages are copyrights and trademarks of
their
Respective corporations.
Release 1.5
ACTiSYS Corporation 2001
2
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
CONTENTS
CONTENTS............................................................................................................................................. 3
INTRODUCTION ..................................................................................................................................... 4
PACKING CHECK LIST.......................................................................................................................... 4
SYSTEM REQUIREMENTS .................................................................................................................... 4
BIOS SETUP VERIFICATION ................................................................................................................. 4
WINDOWS 98 INSTALLATION GUIDE .................................................................................................. 5
WINDOWS 98 UNINSTALLATION GUIDE ............................................................................................. 9
WINDOWS 2000 INSTALLATION GUIDE............................................................................................. 11
WINDOWS 2000 UNISTALLATION ...................................................................................................... 15
WINDOWS ME INSTALLATION GUIDE ............................................................................................... 17
WINDOWS ME UNINSTALLATION GUIDE .......................................................................................... 22
WINDOWS XP INSTALLATION GUIDE................................................................................................ 23
WINDOWS XP UN-INSTALLATION GUIDE ......................................................................................... 28
TROUBLE SHOOTING ......................................................................................................................... 31
SPECIFICATIONS................................................................................................................................. 32
WARRANTY INFOMATION .................................................................................................................. 34
CONTACT INFORMATION ................................................................................................................... 36
Release 1.5
ACTiSYS Corporation 2001
3
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
INTRODUCTION
This document provides instructions to install the ACT IR220L+/220L/200L Serial-IR dongle along with
Windows 98/ME/2000 device driver. It is assumed that the user is familiar with basic operation of Window
98/ME/2000.
PACKING LIST
When you unpack the package, the following items should be found.
1.
2.
ACT-IR220Lplus or ACT-IR220L or ACT-IR200L.
User’s Guide
SYSTEM REQUIREMENTS
To use ACT-IR220L+/220L/220L, your computer MUST meet the following requirements.
1.
2.
3.
Window 98/ME/2000.
One unoccupied Serial (Rs232) COM port .
One unoccupied virtual comport (Com4)
BIOS SETUP Verification
Before installing the device driver, you MUST setup or verify your BIOS FIRST. Below demonstrates a
example of ACT-IR220L+ being installed on Com2.
1. Choose PNP & PCI from BIOS SETUP
PNP OS Installed: NO
Resource Controlled by: Manual
2. Choose Integrated Peripherals from BIOS SETUP
Onboard UART2 Serial Port 2 : 2F8H/IRQ3
Onboard IR function: Disable or
UART2: Normal
Release 1.5
ACTiSYS Corporation 2001
4
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS 98 INSTALLATION GUIDE
Precaution: If you have not verified your Bios setup at this point, we strongly recommend you to refer
back to the Bios verification section and verify your Bios setup again.
Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or
occupied by any hardware or any software. We recommend users to completely delete any files or drivers
that can interrupt clean fresh installation of our product.
Note: You are trying to install a SIR product. Your operating system can always be upgraded to use FIR
products. However you can never downgrade from a FIR product to SIR product, therefore verify that you
have on previously installed any FIR products on your system.
Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a
computer system with at least one serial port and Windows 98 already installed. The best choice for the
system is a desktop.
1.
2.
3.
4.
Connect ACT-IR220L+/200L serial adapter to the COM Port of Desktop PC.
Boot up your computer system.
Double Click My Computer on DeskTop
Double Click Control Panel
5. Double Click Add New Hardware on Control Panel Window.
6. Click Next.
7. Click Next.
Release 1.5
ACTiSYS Corporation 2001
5
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
8. Select No, the device isn’t in the list in the
box. Then click Next.
9. Highlight Infrared Devices from the Hardware
types list, then click Next.
10. Click Next.
Release 1.5
ACTiSYS Corporation 2001
6
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
11. From Manufacturers list, choose (Infrared
COM port or dongle), from Infrared Devices
list, choose (Generic Infrared Serial Port or
dongle). Then click OK.
12. Choose ACTiSYS IR-200L if you are a ACT-IR
200L user. Then click Next.
13. Choose ACTiSYS IR-220L/ 220L+ if you are a
ACT-IR-220L/ ACT-IR220L+ User. Then click
Next.
Release 1.5
ACTiSYS Corporation 2001
7
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
14. Select COM port which is physically connected
to the Dongle. In most cases, the Dongle is
connected to COM2. Choose Communication
Port (COM2) from the Port list, click Next.
15. Reboot your computer.
Release 1.5
ACTiSYS Corporation 2001
8
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS 98 UNINSTALLATION GUIDE
1.
2.
3.
4.
Boot up your computer system.
Click Control Panel.
Double click System Icon
Click Device Manager tab.
5. Highlight Infrared Communication
Device, and then click Remove.
6. Click OK in the Confirm Device Removal
box.
Release 1.5
ACTiSYS Corporation 2001
9
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
7. Highlight (Generic Infrared Serial Port or
Dongle), then click Remove.
8. Click OK in the Confirm Device Removal.
9. Click on OK to restart your computer.
Release 1.5
ACTiSYS Corporation 2001
10
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS 2000 INSTALLATION GUIDE
Note: If you do not change your computer BIOS setting, STOP here and go to Chapter BIOS SETUP.
Note: If your computer system has installed some device on the same com port before, you MUST
properly uninstall the devices first. ACT-IR220L+/220L/200L would NOT work with your system any more if
the devices are uninstalled improperly because some drivers are still there and cause conflicts with
ACT-IR220L+/220L/200L driver. You HAVE to re-install your Windows 2000 again.
Note: If your computer system has installed a FIR device before, ACT-IR220L+/220L/200L would NOT
work with your system any more. You HAVE to re-install your Windows 2000 again.
Note: If you want use Virtual COM Port in your application, STOP here and change
IR220L+/IR220L/IR200L to USB-IR Dongle.
Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a
computer system with at least one serial port and Windows 2000 already installed. The best choice for the
system is a desktop.
1.
2.
3.
4.
5.
Connect ACT-IR220L+/200L serial adapter to the COM Port of Desktop PC.
Startup your computer system
Click on Control Panel.
Double Click Add/Remove Hardware.
On Welcome to the Add/Remove Hardware
wizard, click Next>.
6. Choose Add/Troubleshoot a device, then
click Next>. You may have to wait a while when
the wizard searches for Plug and Play
hardware.
Release 1.5
ACTiSYS Corporation 2001
11
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
7. Highlight ADD a new drive then click Next.
8. Choose No, I want select the hardware form
a list then click OK
9. Select the Infrared device from the Hardware
types.
Release 1.5
ACTiSYS Corporation 2001
12
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
10. From Manufacturers list, choose ACTiSYS,
from Infrared Device list, choose ACTiSYS
IR-200L Serial Infrared Device for IR200L;
click Next>.
11. Choose ACTiSYS IR-220L Serial Infrared
Device for IR220L, click Next>.
12. ACTiSYS IR-220L+ Serial Infrared Device for
IR220L+, click Next>.
Release 1.5
ACTiSYS Corporation 2001
13
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
13. Click Next>.
14. Choose COM2 in most case, then click Next>.
15. Click Finish.
Release 1.5
ACTiSYS Corporation 2001
14
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS 2000 UNISTALLATION
1. Startup your computer system.
2. Click on Control Panel.
3. Double click System Icon.
4. Click on Hardware tab, then click Device
Manager button.
5. Click on Infrared devices, then highlight
ACTiSYS IR-220L+Serial Infrared
Device.
6. Click Action and then Uninstall.
Release 1.5
ACTiSYS Corporation 2001
15
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
7. The device has been uninstalled and close
device manager, restart your computer.
Release 1.5
ACTiSYS Corporation 2001
16
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS ME INSTALLATION GUIDE
Precaution: If you have not verified your Bios setup at this point, we strongly recommend you to refer
back to the Bios verification section and verify your Bios setup again.
Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or
occupied by any hardware or any software. We recommend users to completely delete any files or drivers
that can interrupt clean fresh installation of our product.
Note: You are trying to install a SIR product. Your operating system can always be upgraded to use FIR
products. However you can never downgrade from a FIR product to SIR product, therefore verify that you
have on previously installed any FIR products on your system.
Note: You may experience problems, If you are using a beta version of Windows ME or a old upgrade
edition of Windows ME. Some German version of Windows ME has also known to lack virtual Comports.
This problem may make are device incapable of communicating with other devices.
Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a
computer system with at least one serial port and Windows ME already installed. The best choice for the
system is a desktop.
1.
2.
3.
4.
5.
6.
Connect ACT-IR220L+/220L/200L serial adapter to the COM Port of Desktop PC.
Boot up your computer system.
Double Click My Computer icon on DeskTop
Double click Control Panel icon.
Double click Add New Hardware icon.
On the following boxes, click Next>.
7.
Click Next>.
Release 1.5
ACTiSYS Corporation 2001
17
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
8. Choose No I want to select the hardware
from a list, then click Next>.
9.
If you can not find Infrared device from
Hardware types list, choose Other devices
from the Hardware types list, then click Next >.
Otherwise go to step 16.
10. From Manufacturers list, choose (legacy serial
infrared device), from Models list, Choose
ACT-IR200L Infrared Wireless Interface, then
click Next>.
11. Click Finish.
Release 1.5
ACTiSYS Corporation 2001
18
All Rights Reserved
ACTiSYS Corp.
12.
Serial-IR Dongle Installation Manual
Double click Add New Hardware icon.
13. Click Next>.
14. Click Next>.
15. Choose No I want select the hardware
from list, then click Next>.
Release 1.5
ACTiSYS Corporation 2001
19
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
16. Highlight Infrared device from Hardware
types list. Then click Next>
17. Click Next>.
18. Click Next>
19. If your device is IR200L, choose
ACTiSYS IR200L, click Next>.
Release 1.5
ACTiSYS Corporation 2001
20
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
20. If your device is physically connected to
COM2, highlight Communications ports
(COM2), then click Next>.
21. Click Next>.
22. Click Finish
Release 1.5
ACTiSYS Corporation 2001
21
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS ME UNINSTALLATION GUIDE
1. Double click System icon on Control Panel.
Panel
2. Go to Device Manager, highlight the items in
the Infrared devices, then click Remove
button.
3. Highlight the items in the Infrared devices,
then click Remove button.
4. Highlight (Generic Infrared Serial Port or
dongle), then click Remove button. Click OK
button.
5. The device has been successfully uninstalled.
Release 1.5
ACTiSYS Corporation 2001
22
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS XP INSTALLATION GUIDE
1. Highlight My Computer, right click
2. Highlight Properties, left click
3. Click Add New Hardware Wizard.
Release 1.5
ACTiSYS Corporation 2001
23
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
4. Click Next.
5. Choose Yes, I have already…………….. then
click Next>.
6. Wait processing
Release 1.5
ACTiSYS Corporation 2001
24
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
7. Choose Add a new hardware device, then
click Next>.
8. Choose install the hardware that I manually
select from a list (Advanced), then click Next.
9. Choose Infrared devices, then click Next>
Release 1.5
ACTiSYS Corporation 2001
25
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
10. Choose respective ACT model, then click
Next>
11. Click Next>
12. Choose the Com port which the device
physically connected, click Next>
Release 1.5
ACTiSYS Corporation 2001
26
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
13. Click Finish
Release 1.5
ACTiSYS Corporation 2001
27
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WINDOWS XP UN-INSTALLATION GUIDE
1. Highlight My Computer, then right click.
2. Highlight Properties, then left click
3. Click Device Manager
Release 1.5
ACTiSYS Corporation 2001
28
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
4. Highlight the items under Infrared device, then
right click.
5. Click Uninstall
6. Click OK, you have successfully uninstalled the
device on your system.
Release 1.5
ACTiSYS Corporation 2001
29
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
7. Click OK, you have successfully uninstalled the
device on your system.
Release 1.5
ACTiSYS Corporation 2001
30
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
TROUBLE SHOOTING
For help on general and miscellaneous problems you may be experiencing with your printing, refer to the
following pages for possible solutions. Look up your problem and try the solution.
SYMPTOM
Can not establish link
(General)
PROBLEM
1. The two IR devices are 1.
not aligned properly.
2.
2. Distance is too near or
far.
3.
3. The device is inactivated. 4.
4. The device is not
installed properly
ACT-IR200L/220L+ is The power-saving feature in 1.
connected to and takes the notebook computer
power only from the
either stops or reduces
serial port of the
power output from the
notebook computer.
signal lines of the serial port
to the ACT-IR200L/220L+ 2.
devices.
3.
File Transfer between 1. The infrared
1.
IR-equipped PDA and
communication is
ACT-IR device-attached
interfered. For example,
host computer stops
something blocks out 2.
before finishing up and
the infrared beam or the
an error message
burst of string light
3.
appears.
source, etc.
2. Software does not
support the IrDA
controller chip on the
motherboard.
3. Serial port is occupied
and not available for IR
transmission.
4.
5.
Release 1.5
ACTiSYS Corporation 2001
Solution
Properly align them again
Move one device to a proper
distance.
Activate it by IR monitor.
Refer to Un-installation Guide to
remove the device, then
reinstall again.
Set the “Power Management”
control to “Advanced” or “Off” to
enable power supplied from
computer serial port to
ACT-IR200L/220L+ devices.
Go to Integrate Peripheral to set
the COM port to “Infrared”.
Do not install more than one
infrared devices on one
computer.
Check to find out the source of
interference and eliminate it
before trying again.
If you were restoring data,
simply try again.
If you were doing backup
something the PDA does not
reset its flags and keeps
stopping at the same position
unless you press the RESET
button once. Be very careful.
DO NOT initialize (press ON
key and RESET button at the
same time) your PDA.
Otherwise you may lose all your
data.
Make proper model # selection
in the software as specified in
your PC system user`s manual.
Make sure to disconnect
modem, etc. from the serial port
to make it available for IR
transmission.
31
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
SPECIFICATIONS
Model:
ACT-IR220L+/ACT-IR220L/ACT-IR200L
Carrier:
Infrared radiation (peak wavelength: 850 to 1050nm)
Sub-Carrier:
500 KHz for SHARP ASK-IR and ASK(37KHz) for TV remote spec.(IR200L only)
Communication Distance:
IR200L From 0 cm to 80 cm.
For best results, from 20 cm (7.9in) to 60 cm (1 ft. 11.6 in)
IR220L From0 cm to 250 cm.
For best results, from10 cm (3.95 in) to 150 cm (4 ft. 11.05 in)
SHARP ASK-IR:
Baudrate:
Parity Bit:
Data:
Stop Bit:
Error Check:
9600 bps to 38.4K bps (IR200L only)
Odd
8 bit
1 bit
Check Sum
IrDA-IR:
Baudrate:
Parity Bit:
Data:
Stop Bit:
Error Check:
9.6,19.2,(38.4),57.6,115.2K bps (IR200L/220L+)
None
8 bit
1 bit
CRC
Serial Interface:
Cable Interface (to host computer)
Signal Level: RS-232 Standards
Connector:
DB-9 female connector
Power Source:
PC RS-232 Serial Port
Power Consumption:
0.30mW (11mA max.)
Operating temperature:
0oC to 40oC (32oF to 104oF)
Dimensions (Inches):
2.0”L x 1.63”W x 0.62”H
51mm x 41mm x 16mm
Weight:
2.0 oz (54 gr.)
Accessories:
User Manual
Optional Accessories:
DB9/DB25 Converter
Windows 95/98/ME/2000: IR Software
Release 1.5
ACTiSYS Corporation 2001
32
All Rights Reserved
ACTiSYS Corp.
Pin Assignments:
Pin
2
3
4
5
7
8
Serial-IR Dongle Installation Manual
Serial Interface DB9 female connector
Name
Receive Data
Transmit Data
Data Terminal Ready
Signal Ground
Request to send
Clear to send
Release 1.5
ACTiSYS Corporation 2001
Symbol
RXD
TXD
DTR
GND
RTS
CTS
I/O
I
O
O
O
I
Function
Input signal
Output signal
For data link to build up and maintain
Reference ground (0V) for all signals
Output signal from host computer
Input signal to host computer
33
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
WARRANTY INFOMATION
THE FOLLOWING WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
ACTiSYS Corporation warrants to the first consumer purchaser, for a period of one year from the date of
purchase, that this wireless interface (“the Product”) will be free from defective workmanship and materials,
and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
at no charge to the purchaser for parts or for labor.
This warranty does not apply to any appearance items of the Product, any consumable items such as
paper, ink ribbon, or batteries supplied with the Product, or to any equipment or any hardware, software,
firmware, or peripheral other than the Product. This warranty does not apply to any Product the exterior of
which has been damaged or defected, which has been subjected to misuse, abnormal service or handling,
or which has been altered or modified in design, construction or interfacing. Tampering With Label Voids
Warranty.
In order to enforce the rights under this limited warranty, the purchaser should mail, ship, or carry the
Product, together with proof of purchase, to ACTiSYS.
The limited warranty described above is in addition to whatever implied warranties may be granted to
purchasers by law. To the extent permitted by applicable law, ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR USE ARE LIMITED TO A PERIOD OF
ONE YEAR FROM THE DATE OF PURCHASE. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other
than those described above, or to extend the duration of any warranties beyond the time period described
above on behalf of ACTiSYS Corporation.
The warranties described above shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described above, shall constitute full
satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall ACTiSYS Corporation be liable, or in any way responsible, for any damages or defects in the Product
which were caused by repairs or attempted repairs performed by anyone other than ACTiSYS technician.
Nor shall ACTiSYS Corporation be liable or in any way responsible for any incidental or consequential
economic or property damage. Some states do not allow the exclusion of incidental or consequential
damages, so the above exclusion may not apply for you.
Release 1.5
ACTiSYS Corporation 2001
34
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
ACTiSYS Corporation warrants to the first consumer purchaser, for a period of 1 year from the
date of purchase, that this wireless interface (The Product? Will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or
replace the defective Product or part thereof at no charge to the purchaser for parts or for labor.
This warranty does not apply to any appearance items of the Product, any consumable items
such as paper, ink ribbon, or batteries supplied with the Product, or to any equipment or any
hardware, software, firmware, or peripheral other than the Product. This warranty does not apply
to any Product the exterior of which has been damaged or defected, which has been subjected to
misuse, abnormal service or handling, or which has been altered or modified in design,
construction or interfacing. Tampering With Label Voids Warranty.
In order to enforce the rights under this limited warranty, the purchaser should mail, ship, or carry
the Product, together with proof of purchase, to ACTiSYS .
The limited warranty described above is in addition to whatever implied warranties may be
granted to purchasers by law. To the extent permitted by applicable law, ALL IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS
FOR USE ARE LIMITED TO A PERIOD OF 1 YEAR FROM THE DATE OF PURCHASE. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitation may
not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any
warranties other than those described above, or to extend the duration of any warranties beyond
the time period described above on behalf of ACTiSYS Corporation.
The warranties described above shall be the sole and exclusive remedy available to the
purchaser. Correction of defects, in the manner and for the period of time described above, shall
constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or
otherwise. In no event shall ACTiSYS Corporation be liable or in any way responsible, for any
damages or defects in the Product which were caused by repairs or attempted repairs performed
by anyone other than ACTiSYS technician. Nor shall ACTiSYS Corporation be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may
not apply to you.
Release 1.5
ACTiSYS Corporation 2001
35
All Rights Reserved
ACTiSYS Corp.
Serial-IR Dongle Installation Manual
CONTACT INFORMATION
ACTiSYS Corporation.
48511 Warm Springs Blvd, Suite 206
Fremont, CA 94539, USA
TEL: (510) 490-8024, FAX: (510) 623-7268
E-Mail: irda-support@actisys.com
Web: www.actisys.com
Release 1.5
ACTiSYS Corporation 2001
36
All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising