BASIS 722az - Full Compass
BASIS 722az
QSControl.net Digital System
QSControl.net, QSC’s next generation network
audio system, achieves the seamless integration of
the company’s control, processing, and monitoring
technologies. QSControl.net brings together QSC’s digital,
power amplification and loudspeaker products into a
unified system that enables the user to administrate it
all via a fully integrated graphical user interface. The new
generation BASIS devices are designed to operate under
the company’s QSControl.net platform.
BASIS 722az
The BASIS platform meets the control, monitoring and
processing needs of amplification and loudspeaker systems
over an Ethernet network. The BASIS 722az units combine
two distinct QSC technologies within a single hardware
unit. Amplifier and loudspeaker control, monitoring and
protection, and configurable DSP are seamlessly integrated
into one powerful single RU package.
Through QSControl.net, QSC’s BASIS and next-generation
RAVE and DSP products can be networked together and
controlled from a single software interface. In addition,
multiple networked computers can be set up to control
and monitor all of the units simultaneously.
Inputs
DSP Outputs
Analog DataPort
8 line level
24 x 24
4(8 channels)
Features
• Amplifier and loudspeaker control, monitoring and protection
• Configurable DSP functions and signal paths
• Fixed latency DSP engine
• Ethernet controllable
• Each unit can store eight design configurations that can be changed on the fly
• Snapshots can recall config or block and/or parameter settings
•THX™ approved for professional cinema applications
DSP functions include, but are not limited to:
• Matrix mixer – any size, up to 24 x 24
• Automixers – gain sharing
• Routers – any size, up to 24 x 24
• Gain controls – any channel count, up to 24
• Graphic equalizers
Fixed Latency DSP
Users of most other configurable DSP systems are
familiar with a variable latency inherent in the processing
configuration. Add more processing blocks and you
also add delay, whether you want it or not. QSC’s DSP
engine is unique in having a short and fixed processing
latency through the DSP subsystem. When the A/D and
D/A converters are included, the total analog-to-analog
latency of a single unit is a negligible 2.354 milliseconds.
QSC’s fixed latency DSP is configurable DSP that stays
fast and predictable from one configuration to the next.
•Crossovers – Linkwitz-Riley, Butterworth, Bessel-Thomson in-phase, BesselThomson symmetrical, 2-way, 3-way, and 4-way general purpose adjustable
For more information, visit www.qscontrol.net
• Delays
THX is a trademark of THX Ltd.
•Filters – high-pass, low-pass, all-pass, shelf, parametric, parametric shelf,
Butterworth high and low-pass, Linkwitz-Riley high and low-pass, BesselThomson high and low-pass
• Compressors, peak limiters, AGC’s, gates, dynamics processor
•Duckers – up to 8 channels, up to 60 seconds fade in and fade out times,
priority mix
• Pink noise, white noise, sine generators
• Macros – user-definable custom blocks with password protection
BASIS 722az
PERFORMANCE
Dynamic Range (AES-17, -60 dB method, all sensitivities)
Unweighted A weighted Distortion (20 Hz – 20 kHz, all sensitivities)
+4 dBu (maximum) 2 dB below clip (maximum) Crosstalk (20 Hz – 20 kHz)
Inter-channel (maximum) Inter-channel (typical) Intra-channel (maximum) Intra-channel (typical) Frequency Response
20 Hz – 20 kHz (maximum) 20 Hz – 20 kHz (typical) Audio Converters Mute Delay Analog input through full DSP chain to analog output
INPUTS/OUTPUTS Program Inputs Connector type Type Grounding Pinout Input Impedance Common-mode Rejection
Input Sensitivities (variable)
Program Outputs Connector Type Cable Type Available “Stock” Lengths Maximum Qualified Length MONITOR
Control Room Foldback Monitoring
Connector type Pinout Tap Points Monitor Input
Monitor Signal (unit off) Maximum Level Impedance (nominal) CMRR, 20 Hz – 20 kHz Monitor Output
Monitor Frequency Response (20 Hz – 20 kHz) Distortion (20 Hz – 20 kHz) Noise Floor Output Impedance (nominal) Output Load (minimum) Monitor Level
Control Range (nominal) CONTROL INPUTS/OUTOUTS
Relay Outputs Connector Type Configuration Pinout Switching Capacity (nominal) Logic Outputs Connector Type Configuration Pinout Omni Inputs Connector Type Configuration Pinout Normal Operating Range Potentiometer Operation Voltage Tolerance Current Output RS-232 Port
QSControl Port
Indicators
QSControl Status Power Diagnostic DataPort Status (port) LCD Data Display Specifications
In
> 115 dB > 118 dB Out
> 112 dB > 115 dB Thru
110 dB
113 dB
< 0.009% THD+N < 0.009% THD+N < 0.009% THD+N < 0.009% THD+N < 0.009% THD+N
< 0.009% THD+N
> 75 dB
> 90 dB
> 85 dB
> 100 dB
+/- 0.5 dB
+/- 0.2 dB
24 bit, 48 kHz, in and out
Infinite attenuation
2.354 milliseconds (default group delay) 8 inputs
3-pin “phoenix style” (a.k.a. “euro style”) detachable terminal blocks
Electrically balanced
All shield terminals connected to chassis
1:+ / 2:- / 3:CHASSIS GND
Balanced: 10k ohms / Unbalanced: 10k ohms
20 Hz - 20 kHz (minimum): > 54 dB / 20 Hz - 20 kHz (typical): > 60 dB
Vrms: 1.5, 3, 9, 18 / dBu: 5.7, 11.8, 21.3, 27.3 / dBV: 3.5, 9.5, 19.1, 25.1
8 outputs
4 HD-15 DataPort connections
QSC DataPort cable, QSC p-n DPC-x (“x” designates cable length in feet)
1, 2, 3, 4, 5, 6, 10, and 20 ft., custom lengths available
328 ft. (100 m) using QSC DP cable only / Non QSC cable limited to 6 ft. (audio only)
5-pin “phoenix style” (a.k.a. “euro style”) detachable terminal blocks
1:+(input) / 2:-(input) / 3:CHASSIS GND / 4:-(output) / 5:+(output)
8 internal input / 8 internal output / 8 amplifier (pre-, post-, amplifier) software selectable
Unity gain connection, relay bypass
+21 dBu
10k ohms
> 54 dB
Sum of monitor input and signal from internal monitor tap point(s)
+/- 0.5 dB
< 0.05% at +4 dBu
> 90 dB
100Ω
600Ω
0 dB to -95.5 dB in 0.5 dB steps
2 discrete floating relay switch outputs
3-pin “phoenix style” (a.k.a. “euro style”) detachable terminal blocks
Electromechanical relay
1:NC / 2:NO / 3:COM
1A 30 VDC
4 discrete outputs
2-pin “phoenix style” (a.k.a. “euro style”) detachable terminal blocks
Single-ended, TTL compatible
1:+(Signal) / 2:-(CHASSIS GND)
6 discrete inputs for TTL logic, voltage control or passive resistance
2-pin “phoenix style” (a.k.a. “euro style”) detachable terminal blocks
Single-ended, ground referenced
1:+(Signal) / 2:-(CHASSIS GND)
Reads signals between 0-5 V nominally
Use 10k ohms for full range
+/- 48 V
0.5 mA with 10k pot (for passive resistive controls)
Female DB9 connector (setup and diagnostics purposes only)
Neutrik Ethercon RJ45 ruggedized data connector
Yellow Link, Tx, Rx, front panel / Green Link, Tx, Rx, rear panel
Blue, front panel
Red, front panel
Tri-state (red, green, yellow), front panel
2 line x 16 character, backlit, front panel
Specifications subject to change without notice.
1675 MacArthur Boulevard • Costa Mesa, CA 92626 • Ph: 800/854-4079 or 714/957-7100 • Fax: 714/754-6174
BASIS 722az - 04/23/07
qscaudio.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement