Owner`s Manual
Owner’s Manual
READ AND SAVE THESE INSTRUCTIONS!
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and
proper installation. Therefore, before attempting to install and operate your Casablanca fan, read this Owner’s
Manual completely and carefully. Retain this manual and other included documentation for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker
or fuse box before attempting any installation procedure.
CONTENTS
INTRODUCTION
Before You Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MOUNTING RECOMMENDATIONS
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION
Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Crossbar Mounting Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Lag Screw Installation (required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
W-81 Wall Control Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Light Fixture Installation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switch Housing and End Cap Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CARE RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PN C1943001 AT0708
1
INTRODUCTION
BEFORE YOU START
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code,
ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified
electrician. To avoid overheating and possible damage to other equipment, do not install control to a receptacle,
fluorescent light fixture, motor-operated appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for
ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are available for
sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The
maximum current requirement for the fan with light fixture is 3.1 amps. The fan uses about 1.1 amp or 132 watts.
Maximum light current is about 2.0 amps or 190 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy
hatch, make sure all wires are within the canopy and that no wires are being pinched.
• WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the
fan. Do not insert foreign objects in between the rotating fan blades.
• The fan must be supplied with 3 independent 120V AC supply wires to provide power for the fan, the light, and
neutral.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have
been removed.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal weight
to assure smooth fan operation. If more than one fan
is being installed, be careful not to mix blades from
different cartons.
Fuse Box
(Remove fuse for the
circuit you will be
working on)
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
• Inspect the contents of your carton for possible
shipping or handling damage. If parts are missing or
damaged, call 1-888-227-2178.
• It is always a good idea to have an assistant to help
with the installation.
• When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn the
power OFF to the ceiling fan before working on it or
replacing lightbulbs.
• Never insert anything into the path of the fan blades
while the fan is in operation.
from
wall
18"
70"
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged
i n a n y w a y. F o r a s s i s t a n c e i n o b t a i n i n g
service, call Casablanca Fan Company at
1-888-227-2178 or contact your local authorized
Casablanca dealer.
84"
from bottom
edge of blade
to floor
Dimensions indicated are the minimum
allowable for proper installation.
2
MOUNTING RECOMMENDATIONS
GENERAL GUIDELINES
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and
fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We
suggest you follow these mounting recommendations as you decide where
to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7' above the
floor.
• Do not locate the fan in a doorway or above a swinging door.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage
from pool cues.
• In kitchens, be sure to allow for open cupboard doors to clear the fan
blades.
• Do not install a fan close to or over a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 60" fan even in smaller rooms. For very large rooms, two fans may
be needed.
SLOPED CEILING INSTALLATIONS
SUGGESTED EXTENSION DOWNROD LENGTHS
Ceiling Height
9' 0"
9' 6"
10' 0"
11' 0"
12' 0"
13' 0"
14' 0"
15' 0"
Downrod Length
Extension
Downrod
Maximum
Hang-Tru®
angle 32º
3"
3"
12"
18"
24"
36"
48"
60"
Blades must be a
minimum of 7 feet
above the floor
7' minimum
When to Use an Extension Downrod
For optimum performance and appearance, an
extension downrod should be used with your
Casablanca fan when installing on high (cathedral)
ceilings or sloped ceilings. Casablanca offers
standard downrods in increments of 6" up to 60". See
your Authorized Casablanca Dealer for details.
EXAMPLE 1
NOTE: The fan may wobble or vibrate if pole length is
not long enough and the inside blade is too close to
the downslope or side wall. Using a longer downrod
will usually solve the problem.
EXAMPLE 2
Calculation of Ceiling Angle
Use the tear-off Ceiling Angle Template card inserted
in this manual. It provides you with a simple “go” or
“no go” for installing your fan on a sloped ceiling.
EXAMPLE 3
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum slope that will allow the fan to
hang straight down. It is OK to install
your fan.
This slope is more than 32º. Your fan
will not hang straight down. Contact
your local Authorized Casablanca
Dealer.
3
FAN INSTALLATION
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
Using Existing Ceiling Fixture Outlet Box
If you do not have an existing fixture located where
you wish to place your Casablanca fan, an approved
ceiling fixture outlet box must be installed and wired.
After turning the power OFF at its source (either the
circuit breaker or fuse box), lower the old fixture and
disconnect the wiring. Check the ceiling fixture outlet
box to be sure it is marked “Approved for Ceiling Fan
Mounting.” If it is not, a new box must be installed.
WARNING!
To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box
marked “Acceptable Fan Support of 22.7
kg (50 lbs.) or less” using the mounting
hardware provided with the outlet box.
CROSSBAR MOUNTING BRACKET INSTALLATION
CEILING HARDWARE (not to scale)
Crossbar Mounting Bracket
Rubber
Gasket
Mounting
Plate
Lag Screw and Washer (1)
1" x 8-32 Roundhead Screws and Washers (2)
Wire Nuts (4)
Note: After removing the old fixture, check the outlet
box to ensure that it is supported by a joist or beam
across its upper surface. If not, a 2 x 4 stud must be
installed.
Step 1a. Remove the knockout plug in the center of
the outlet box or drill a 1/2-inch hole for the lag screw
to pass through. Then drill a 1/4-inch guide hole into
the joist or beam to a depth of 3 inches.
Step 1b. The rubber gasket has a cutout already in
the gasket for the wires as shown in Figure #1. Route
the outlet box wires through the rubber gasket and the
mounting plate as shown in Figure #2.
CUTOUT
FOR WIRES
JOIST
CEILING FANAPPROVED
WIRING BOX
RUBBER
GASKET
MOUNTING
PLATE
Figure #1
4
Figure #2
1 2"
/
HOLE
CEILING
WIRING
Step 1c. After routing the outlet box wires through the
rubber gasket and the mounting plate, route the outlet
box wires along side of the crossbar mounting bracket
as shown in Figure #3. Attach the crossbar mounting
bracket to the outlet box with the screws provided. First
you will need to make a hole in the rubber gasket for
the screws before attaching the crossbar mounting
bracket to the outlet box. Make sure the outlet box
wires are not pinched by the washer.
JOIST
CROSSBAR
MOUNTING
BRACKET
CAUTION:
To reduce the risk of personal injury, use
only the mounting hardware provided
with the approved outlet box to install the
crossbar mounting bracket.
WASHERS
WARNING!
GREEN
GROUND WIRE
Support directly to building structure only.
1" x 8-32
ROUNDHEAD
SCREWS
Figure #3
5
LAG SCREW INSTALLATION (REQUIRED)
NOTE: This step is required only under two conditions:
If the fan weighs 36 lbs. or more or if the existing ceiling
fixture outlet box needs to be modified for a ceiling
fan application (for example, if the house is not new
construction and you are replacing an existing light
fixture). We recommend that the ceiling box be of
sufficient capacity to support the weight of the fan and
light fixture under any conditions. If in doubt whether
you need to install the lag screw, consult a qualified
electrician.
Step 2. Pass the lag screw through the center hole
of the crossbar mounting bracket and screw into the
guide hole. Tighten until the outlet box is mounted
firmly to the beam. This box must be secured to the
ceiling firmly.
CANOPY INSTALLATION
CANOPY HARDWARE (not to scale)
Canopy Hatch
Canopy Screws and Lock Washers (4)
Canopy
Phillips
Screwdriver
Step 3. Attach the canopy to the crossbar mounting
bracket with three of the 8-32 x 21/2" long canopy screws
and lock washers provided with your Casablanca fan.
Tighten using the provided screwdriver until snug
against the ceiling.
NOTE: On sloped ceilings, align the canopy opening
with the top or peak of the room.
CANOPY
CANOPY SCREWS
LOCK WASHERS
6
FAN PREPARATION
PERMA•LOCK™ HARDWARE AND TOOLS NEEDED (not to scale)
3"Perma•Lock™ Downrod
and Ball Assembly
Pole Cover
Set Screw
IMPORTANT SAFETY INFORMATION:
Allen Wrench
PAPER MOTOR
SHIELD
Before starting the installation of your
ceiling fan, install the threaded downrod into
the motor coupling and lock the assembly.
Figure #1
MOTOR WIRES
(LEAVE AT LEAST
6" LONG)
Prepare for fan installation as follows:
Step 4a. Remove the paper shield (Figure #1) from
the motor.
POLE COVER
Step 4b. Locate the Set Screw as shown in Figures
#2 and #3. If the end of the Set Screw can be seen
within the motor coupling as shown in Figure #3, you
will need to unscrew the Set Screw so that the tip
of the Set Screw does not remain in the path of the
downrod.
TAPERED
THREAD
SET SCREW
PERMA•LOCK™
DOWNROD AND
BALL ASSEMBLY
MOTOR
COUPLING
MOTOR
HOUSING
ASSEMBLY
Figure #2
Step 4c. Slide the pole cover on to the downrod, then
route the wires through the 3" Perma•Lock downrod
and ball assembly as shown in Figures #2 and #4.
Insert the downrod into the motor coupling and turn it
clockwise until it stops turning as shown in Figure #4,
ensuring that the downrod has bottomed out.
TIP OF SET SCREW
ALLEN
WRENCH
TIP: The downrod has a tapered thread as shown in
Figure #4 that is designed to lock completely when
installed correctly.
Figure #3
Step 4d. Tighten the Set Screw with the Allen wrench
as shown in Figure #4 to ensure safe operation of your
fan. If it is tight enough, you should not be able to turn
the downrod counterclockwise with your hands. If in
doubt, tighten the Set Screw with the Allen wrench
until you cannot turn it any further.
CAUTION: Failure to fully screw in the
downrod all the way into the motor coupling
may cause the fan to separate from the
downrod and fall during normal operation.
PERMA•LOCK™
DOWNROD AND
BALL ASSEMBLY
SET SCREW
ALLEN
WRENCH
Figure #4
7
HANGING THE FAN
Step 5a. To hang the fan body in the canopy, hold
the fan body firmly and insert the ball into the canopy
opening. Check that no wires are pinched. Rotate
the fan body until the slot in the ball fits into the pin
opposite the canopy opening.
BALL
Step 5b. Trim excess motor wires, leaving at least
6 inches above the downrod. Strip ½-inch insulation
from the end of each wire using a wire stripper
(available at your local hardware store).
SLOT
PIN
CANOPY ELECTRICAL CONNECTIONS
Step 6. Attach the fan wires to the ceiling fixture outlet
box wiring by placing the bare ends of the wires side
by side and then securing with a wire nut. Test that
the connection is secure by pulling on the wire nut.
Connect in this order:
• GREEN leads from mounting plate and downrod
assembly of fan to GROUND conductor of power
source. Secure with wire nut.
WIRE NUT
RED AND BLUE
WIRES
• WHITE wire from fan to white NEUTRAL wire in
ceiling fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire
in ceiling outlet box. Secure with wire nut.
2 BLACK WIRES
• BLUE D1-OPTION wire from fan to RED power
wire (second hot wire) in ceiling outlet box. Secure
with wire nut.
2 WHITE WIRES
After making the wire connections, the wires should
be spread apart with the grounded conductor and
the equipment-grounding conductor on one side of
the outlet box and the ungrounded conductor on the
other side of the box. The splices after being made
should be turned upward and pushed carefully into
the outlet box.
3 GREEN WIRES
NOTE: If the color of your ceiling wires differs from that
described, consult an electrician.
CANOPY HATCH INSTALLATION
Step 7a. Tuck the wires into the canopy with the wire
nuts pointed upwards, so that the WHITE and BLACK
wires are on opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 7b. Install the canopy hatch with the last
canopy screw and lock washer using the provided
screwdriver. To do this, tilt the fan body away from
the hatch opening. Tighten the screws firmly.
Step 7c. Straighten the fan, then check to ensure that
there is no movement between the canopy and the
ceiling or the downrod and the ball assembly.
8
CANOPY
HATCH
CANOPY
SCREW &
WASHER
CANOPY
W-81 WALL CONTROL INSTALLATION
CONTROL HARDWARE (not to scale)
Wall Plate
Screws (4)
W-81 Wall Control
(assembled)
Wall Plates (2)
Wall Control (1)
Switch Box
Screws (4)
Wire Nuts (4)
W-81 WIRING DIAGRAM
• The fan must be supplied with three independent
120V AC supply wires to provide power for the fan,
the light, and neutral.
• The fan can be turned ON and OFF by the wall
control.
• The optional light fixture can be turned ON and OFF
by the wall control and the intensity adjusted from
Low to High.
• The W-81 is designed to replace a standard wall
switch and will fit wall boxes (metal or plastic) with a
depth of 2" or greater.
1. Remove the screws and switch plate from the
existing switch box.
2. Remove the screws holding the switch in the
switch box.
3. Pull the existing switch from the switch box to
expose the wire connections.
4. Remove the three wires from the switch.
5. Prepare wires if necessary, by stripping ½-inch
insulation from the end of each wire using a wire
stripper.
CAUTION! Ensure the power is turned OFF
at the breaker or fuse panel before starting
installation.
9
NOTE: The wire connectors provided are suitable
for copper wire only. Use to join the following wire
combination: One No. 14 gauge with one No. 16 or
18 gauges.
BLACK
WIRE
(LIVE)
YELLOW
WIRE
(FAN)
6. Connect in this order:
• GREEN GROUND conductor from the wall box to
the GREEN wire from wall control (labeled GRD).
• BLACK wire from fan in the wall box to YELLOW
wire on wall control (labeled FAN).
(GRD)
GREEN
WIRE
• RED wire from fan in the wall box to RED wire on
the wall control (labeled LIGHT).
(LIGHT)
RED
WIRE
Figure #1
NOTE: BLUE D1 optional fan wire to RED power wire
in ceiling outlet box.
• BLACK wire form the source of power (HOT WIRE)
wire in the wall box to BLACK wire on wall conotrol
(labeled LIVE)
NOTE: If the colors of your wiring differ from that
described, consult an electrician.
7. Inspect each wire nut and ensure that no bare wire
is visible. Pull on each wire to test if the connection
is mechanically sound.
8. Install the W-81 in the wall box with the two switch
box screws provided as shown in Figure #2.
SWITCH BOX
SCREWS
Figure #2
CAUTION! Be sure no wires are pinched!
9. Install the wall plate on to the switch and screw in
the two wall plate screws as shown in Figure #3.
WALL PLATE
SCREWS
Figure #3
10
BLADE INSTALLATION
BLADE HARDWARE (not to scale)
Blades (5)
(packed separately)
Blade Irons (5)
Blade Iron
Screws (11)
Blade Badges (5)
Blade Screws (21)
Phillips
Screwdriver
NOTE: Blades are packaged separately based on
blade style. For illustrative purposes, the BL-ADK-RA
(Adirondack Reclaimed Antique) blades are shown.
Please use the instructions below for all three blade
types.
Step 8. Remove the five shipping blocks, washers,
and screws as shown in Figure #1. DO NOT discard
the five screws; you will need them for installing the
blades onto the fan.
SHIPPING BLOCK
Attach Blade Irons
Step 9. Attach a blade to a blade iron by first pressing
the blade badge onto the blade, then attaching the
blade iron using four blade screws as shown in Figure
#1. Using the provided screwdriver, tighten securely
by hand only. Repeat for each blade assembly.
Figure #1
BLADE IRON
BLADE BADGE
BLADE
Blade Installation
Step 10. Before attempting to attach the blades,
review Figure #3 for blade placement on the blade
holder adapter ring. The numbers and lines show
screw placement when attaching the five blade irons
and blades assemblies to the fan. When placing
the blades on the adapter ring, each blade iron will
cover one of the five adapter ring mounting screws
as shown.
Figure #2
BLADE BADGE
SCREWS
BLADE
HOLDER
ADAPTER
RING
Figure #3
11
Blade Installation
Step 11. Attach a blade/blade iron assembly to the
blade ring by using two blade iron screws provided.
Place the end of the blade iron on the blade holder
adapter ring as shown in Figure #4. Insert the screws
one by one using the provided screwdriver. Tighten
securely by hand only. Repeat for each blade/blade
iron assembly until all five blades are attached to the
fan as shown in Figure #5.
BLADE / BLADE
IRON ASSEMBLY
BLADE HOLDER
ADAPTER RING
CAUTION:
BLADE IRON SCREW
Figure #4
Blade screws must be tightened securely
before operating the fan.
Figure #5
LIGHT FIXTURE INSTALLATION (OPTIONAL)
Step 12. If you have purchased a Heritage™ compatible light fixture for your fan (KGC10W, KGC12W, or
KGC19W), you will need to install it at this time. Using the instructions and hardware packed with the fixture;
install it on the fan and skip steps 13-15. If you did not purchase a light fixture for your fan, continue with Step
13.
12
SWITCH HOUSING AND END CAP INSTALLATION
SWITCH HOUSING HARDWARE (not to scale)
Switch Housing Plate
Switch Housing Screws (3)
Switch Housing
Plate Gasket
Adapter Plate Screws (3)
Adapter Plate
Cover Plate Screws (2)
End Cap
Phillips
Screwdriver
Switch Housing Installation
Step 13a. Install two of the three switch housing
screws onto the switch housing adapter plate as
shown in Figure #1.
Step 13b. Thread BLUE and WHITE wires through
the hole in the center of the switch housing plate
and align the two keyholes with the two screws
that were installed on the switch housing. Place the
switch housing plate over the two screws and rotate
it clockwise so that the two screws are holding the
switch housing plate as shown in Figures #2 and
#3.
Step 13c. Align the screw hole on the switch
housing with the screw hole in the switch housing
plate and insert the third screw as shown in Figure
#3. Then tighten all three screws with the provided
screwdriver.
SWITCH
HOUSING
SCREWS
SWITCH
HOUSING
PLATE
Figure #2
SWITCH
HOUSING
SCREWS
Figure #1
TIGHTEN 3
SCREWS
Figure #3
13
Step 14a. Locate the two RED ARROWS printed
on the WHITE sticker as shown in Figure #4. Using
the screwdriver provided, attach the switch housing
plate gasket to the switch housing plate by screwing
in two of the three screws shown in Figure #4 part
way only.
Step 14b. Carefully tuck the wires so they do not
get pinched, then align the two key holes on the
adapter plate with the two screws that were installed
onto the switch housing plate as shown in Figure
#5. Place the adapter plate over the two screws and
rotate the adapter plate clockwise so that the two
screws are holding the adapter plate to the bottom
of the fan as shown in Figures #4 and #6.
Step 14c. Screw in the last of the three screws
holding the adapter plate to the bottom of the fan
as shown in Figure #6 and tighten all three screws
with the screwdriver.
SWITCH HOUSING
PLATE GASKET
Figure #4
Figure #5
TIGHTEN 3
SCREWS
Figure #6
14
2 SCREWS
Step 15. Align the two holes on the End Cap with the
two screw post located on the bottom of the adapter
plate as shown in Figure #7. Then with the provided
screwdriver, use the two cover plate screws to attach
the End Cap to the fan as shown in Figure #8.
SCREW
POSTS
END CAP
COVER PLATE
SCREWS
Figure #7
Figure #8
15
TROUBLESHOOTING TIPS
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEM
POSSIBLE REMEDIES
Fan wobbles or shakes excessively
• Be sure the canopy pin is set properly into the slot on the ball.
• Check that the bladeholders have not been bent during installation and the blades
are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure
the hanger bracket is attached tightly to the ceiling outlet box and the downrod
assembly is secured firmly.
• The downrod is attached to the downrod base too loosely. Make sure all the
screws are securely tightened.
Fan is noisy during operation
• Tighten the canopy screws and mounting plate assembly. Make sure the wire
nuts inside the canopy and switch housing are not touching the metal parts and
that they have not fallen off the wire splices. Tighten as necessary.
• Tighten the blade holders to the direct drive motor and the blades to the bladeholder
screws.
• Make sure all the screws in the motor housing are snug but not overly tight.
• Check and tighten the light fixture retaining screws, glass shade screws, and/or
lightbulb(s).
Fan does not run on low speed
• If fan is new, it may need to be “broken in.” Run at high speed for several days.
CARE RECOMMENDATIONS
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened
soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
Blades
• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a
mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents
as these will damage the finish.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated
for life.
• Do not attempt to oil the motor.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178
or visit us on the web at: www.casablancafanco.com
16
PRODUCT SPECIFICATIONS
Model Name:
Model Number:
ETL Rating:
Motor:
Blade Span:
Blade Pitch:
No. of Blades:
Technology:
Heritage™
C19xxxF
Wet
XTR200™ 30mm
60"
14°
5
W-81 four-speed wall control
Weight
(lbs)
Speed*
(rpm)
Airflow*
(cfm)
Electricity
Use*
(watts)
Airflow
Efficiency*
(cfm/watt)
A
B
C
D
E
BL-ADK-RA
(Adirondack Reclaimed Antique)
39
167
7,932
96.4
82.3
12.7
13.4
2.9
16
5.6
BL-TDW-BK
(Traditional Wicker Black)
45
125
6,780
97.2
69.8
12.7
13.4
2.9
16
5.6
BL-TPW-WB
(Tropical Wicker Weathered Bronze)
47
155
6,736
99.3
67.8
13.3
13.4
2.9
16
5.6
Motor with Heritage™ Compatible
Blades
* = At high speed
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes
or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement