==
—
OQ
OO
=
а
L
<C
pe
oc
LL]
Ve
—
<L
WSP 2010, WSP 3010, Deutsch
WSP 4010, WSP 5010,
WSP 6010, WSP 7010
Wärmespeicher
Standard-Baureihe
Gebrauchs- und Montageanweisung
WSP 2010, WSP 3010, English
WSP 4010, WSP 5010,
WSP 6010, WSP 7010
Electric Storage Heaters
Standard Series
Operating and Installation instructions
WSP 2010, WSP 3010, Franca
WSP 4010, WSP 5010,
WSP 6010, WSP 7010
Accumulateurs de chaleur
Série standard
Notice d'utilisation et de montage
WSP 2010, WSP 3010, Nederlands
WSP 4010, WSP 5010,
WSP 6010, WSP 7010
Warmteaccumulator
— standaard serie
Gebruiks- en montagehandleiding
20 (N4)
co
|
|
A
|
An
| 21 (F1)
di
THEME
ISSN
—
©
||
L
—— — —
19 (N5) 13 18
ES
NX
240mm =100mm
= |
So
CC oC III CD |
шее
Е | : г р Ро! {г == 1 >500mm =>
BETA
I
Ii
NN NN
=
Fr |
|
-
|
|
—
o
Deutsch
Inhaltsverzeichnis
1.
Gebrauchsanweisung
Fiir den Benutzer
1.1 Gerátebeschreibung
1.2 Bedienung _
1.3 Sicherheitshinweise =
1.4 Pflege und Wartung
1.5 Wichtiger Hinweis
Was tun wenn... ?
O e “uu Y Oh oO
. Montageanweisung
Fur den Installateur
2.1 Technische Daten
2.2 Gerätebeschreibung
2.3 Vorschriften und Bestimmungen
2.4 Montageort
2.5 Gerátemontage
2.6 Erstinbetriebnahme __
2.7 Instandsetzung, Umbau des Gerátes __
2.8 Ubergabe
. Kundendienst und Garantie
3.1 Entsorgung von
Verpackung und Altgerát
Francais
Sommaire
2.2 Description de l'appareil
. Notice d'utilisation
À l'intention de l'utilisateur
1.1 Description de l'appareil
1.2 Commande
1.3 Consignes de sécurité
1.4 Entretien et maintenance
1.5 Remarque importante
Que faire si … ?
Notice de montage
À l'intention de l'installateur
2.1 Caractéristiques techniques
2.3 Consignes et réglementations
2.4 Site de montage
2.5 Montage de l'appareil
2.6 Première mise en service
2.7 Réparation, modification de l'appareil _
28 Remise à l'utilisateur
. Environnement et recyclage
10
11
12
12
16
16
16
19
20
35
35
36
36
37
37
38
39
40
41
41
45
45
48
English
Table of Contents
1. Operating instructions
For the user
1.1 Technical description
1.2 Operation
1.3 Safety instructions
1.4 Care and maintenance
1.5 Important note
What to do when ..?
2. Installation instructions
For the fitter
2.1 Technical data
2.2 Technical description
2.3 Rules and regulations
2.4 Installation
2.5 Unit installation
2.6 First-time operation
2.7 Repair, conversion of unit
2.8 Transfer
3. Environment and recycling
Nederlands
Inhoudsopgave
1. Gebruiksaanwijzing
Voor de gebruiker
1.1 Beschrijving van het apparaat
1.2 Bediening
1.3 Veiligheidsvoorschriften
1.4 Verzorging en onderhoud
1.5 Belangrijke aanwijzing
Wat te doen wanneer ...?
2. Montagehandleiding
Voor de installateur
2.1 Technische gegevens
2.2 Beschrijving van het apparaat
2.3 Voorschriften en bepalingen
2.4 Montageplaats
2.5 Montage van apparaat
2.6 Eerste inbedrijfstelling
2.7 Reparatie, ombouwen van het apparaat
2.8 Aflevering
3. Milieu en recycling
21
21
22
22
23
23
24
25
26
27
27
31
31
31
34
49
50
50
51
51
52
53
54
55
55
59
59
62
For the User
1. Operating Instructions
1.1 Technical Description
Storage heaters store electrically generated heat during low-cost electricity tariff periods
(depending on the electricity supply company, mainly during the night hours). This is then
discharged according to the desired room temperature as hot air by a fan and to a smalt extent
through the surface of the heater.
1.2 Operation
The unit is operated by the contro! pane! (1) on the right side wall (fig. 1).
1.2.1 Heat Storage
The degree of heat storage (charging) is determined by the selector knob (fig. 17).
A distinction needs to be made here between operation of the storage heater with or without
central weather-controlled charging control unit {is in the sub-distributor).
If there is no central, weather-controlled charging control unit (manual operation, fig. 18), the
selector knob should be set as follows:
e = no charging
1 = Transitional period (Spring/Autumn) - corresponds to about 1/3 full charge
2 = Mild Winter days - corresponds to about 2/3 full charge
3 = Winter days - corresponds to full charge
After a short while you will soon have the necessary experience to find the right setting every
time.
If there is a central, weather-controlled charging control unit (automatic operation), the selector
knob should be set to position 3. The weather-controlied charging control unit then takes care of
the right charging. For varying contro! of individual storage heaters, the charging volume can be
adapted manually with the selector knob even when a charging control unit is available.
1.2.2 Heat Discharge
The heat discharge is controlled by a wall-mounted or integrated AEG room temperature
regulator (special accessory).
The desired room temperature must be set at the room temperature regulator which then controls
the heat discharge automatically with the fan so that the set room temperature is kept constant.
On very cold days it is advisable to leave the room temperature regulator switched on during long
periods of absence (several days) to keep the temperature at about 10 °C for example so that the
building or room does not go cold (protection against frost).
21
22
For the User
1.3 Safety Instructions
A
The unit must not
- be operated in rooms where there is a risk of fire or explosion due to chemicals, dust, gases or
fumes;
— be operated in the immediate vicinity of pipes or containers which carry or contain inflammable
or explosive substances;
- be operated when the minimum distances from adjacent object surfaces are not kept.
e This unit must only be installed (electrical installation), commissioned and maintained by an
authorised expert according to these instructions.
The unit must on no account be operated when work on floors such as laying, sanding, sealing,
cleaning with petrol and caring (spray, wax) and similar is being performed.
Then the room must be adequately aired before charging.
e The heater's casing surfaces and the air outlet grille can heat up to temperatures above 80 °C.
Therefore no inflammable, ignitable or heat insulating objects or materials such as washing,
blankets, newspapers, containers of floor wax or petrol, aerosol cans and similar may be placed
on or in the immediate vicinity of the heater. Washing must never be hung over the heater to
dry. Danger of catching fire!
e The following minimum distances must be kept from the heater by all kinds of objects, e.g.
furniture, curtains and textiles or other flammable and non-flammable materials especially from
the air outlet grid (fig. 2):
to the air outlet grille => 500 mm
from the right side wall (for installation clearance) = 100 mm
from the left side wall => 70 mm
from the left side wall with two storage heaters next to one another = 100 mm
from the cover (e. g. window ledge} > 40 mm
from the cover (curtains, inflammable materials) = 100 mm
The hot air must be able to discharge unhindered (fig. 19)!
e The label enclosed with these operating and installation instructions "Do not place objects on or
lean them against the heater" must be affixed well visibly on the top of the heater in
commercially used rooms such as hotels, holiday homes, schools etc.
1.4 Care and Maintenance
If slight brown discoloration of the unit housing should occur, this should be rubbed off
immediately with a soft cloth.
The device should be cleaned cold with normal cleaners.
Abrasive and aggressive cleaners should be avoided.
Do not spray cleaning spray into the air vents.
The ventilation duct behind the air outlet grille (5) should be checked by a specialist every two
years. Slight dirt deposits may accumulate here.
We recommend that you have the inspection and control elements checked during regular
maintenance. Safety, inspection and control elements as well as the entire charging and discharge
control system should be checked by a specialist 10 years after first commissioning at the latest.
1.4.1 Cleaning the Fluff Screen (fig. 3)
The fluff screen (7) located in the air inlet grille (6) must be cleaned regularly,
so that fault-free discharging of the storage heater is guaranteed.
The fans switch off when the fluff screen is blocked.
Proceed as follows to clean the fluff screen.
— Press the air inlet grille (6) down slightly on both sides, tip forward at the front and remove;
~ Press the fluff screen out of the grille with a screwdriver for example and clean with a brush,
vacuum cleaner or similar;
Replace the fluff screen in the grille and snap in the lugs.
— Place the air inlet grille at an angle on the lugs in the unit base and snap in under the air outlet
grille by pressing lightly (fig. 16).
For the User and Fitter
1.5 Important Note
AN
What to do when .. . ?
Keep these instructions in a safe place, pass on to the new owner in case of a change of ownership.
Make them available to the specialist in the case of repair work.
For the User
For the specialist
e the storage heater
does not get hot
* the storage heater
housing should get
extraordinarily
hot even in mild
weather
Check whether ...
. the selector knob is set to
position 3.
. the corresponding fuses in
“your fuse box are defective or
the Fl switch has switched off.
Eliminate the cause!
If the following day the
storage heaters have still not
heated up, call a specialist.
Check whether...
. the fan can be switched on
with the room temperature
regulator.
If not, call a specialist.
. the fluff screen in the air inlet
griile is blocked.
Eliminate cause as described
in section 1.4.1!
Check whether ... |
... the control of the heating
element contactor is OK.
. there is a voltage at terminals
L1/L2/L3.
. whether the safety temperature
limiter (F1) has triggered.
Check whether ..
. the room temperature
regulator has switched on and
voltage is applied at terminal
. the fans are turning.
... the safety temperature
regulator "(N5, see page 3,
fig. 1) in the air outiet has
switched off.
. the control signal Z1 of the
charging control unit is applied
at terminal A1/21 in the
storage heater.
23
“English |
24
2. Installation Instructions
2.1 Technical Data
For the Fitter
TF
+ 1
co
650
=
The unit must be installed and connected by a specialist under consideration of these installation
Instructions.
WSP 2010 | WSP 3010 | WSP 4010 | WSP 5010 | WSP 6010 | WSP 7010
Width "B" mm 605 780 955 1130 1305 1480
Weight (with storage blocks} kg 118 169 220 271 322 373
Distance "X" mm 415 590 765 940 1115 1290
Connection * 3/N/PE ~ 50 Hz 400 V
Power kW 2.0 3,0 4.0 5.0 6.0 7.0
Reference charging kWh 16.0 24.0 32.0 40.0 48.0 56.0
max. charging P, kWh 17.0 25.5 35.0 42.0 51.0 61.5
Storage blocks
Number of packages (blocks) pcs. 6 (12) 9 (18) 12 (24) 15 (30) 18 (36) 21 (42)
Block weight kg 85 128 170 213 256 298
Control resistance ко 2.78 2.78 2.78 2.78 2.78 2.78
Supplementary heating (special accessories)
Power kW! 035 | 05 0.8 1.0 1.2 1.5
* WSP 2010 also with 1/N/PE ~ 50 Hz 230 V connectable
for the Fitter
2.2 Technical Description (page 3, fig. 1)
Control panel
Cover
Right side wall
Front wall
Air outlet grille
Air inlet grille
Fluff screen
Inside front wall
Storage blocks
Cover plate
Thermal insulation
Floor thermal insulation
Mixing air flap
Air duct
Cable duct
Air guidance assembly
Heating element
Fan
Safety temperature regulator - discharging (N5)
Safety temperature regulator - charging (N4)
Safety temperature limiter (F1)
№№) №) == ed — owed od ond ak ak md md
= © © 09 ч ос о в м = @ ® 69 М ©) сл Фо © КЮ —
2.2.1 Function Principle
The storage blocks are heated up by the heating elements between the rows of storage blocks.
Charging is set continuously with the charging control unit (selector knob fig. 17)
Start and duration of the charging time are determined by the responsible electricity supply
company.
Two built-in safety temperature regulators (19, 20) and a safety temperature limiter (21) prevent
overheating of the unit. Whilst the safety temperature regulators switch on again automatically,
the safety temperature limiter must be switched back on by the technician by pressing in the knob
in the middle of the limiter after eliminating the cause of the error.
The heat stored in this way is then discharged with the aid of a fan, also partly through the heater
surface. In this case, the room air is sucked in through the air inlet grille (6) by the fan (18) and
blown through the air ducts of the storage blocks (9) which heats them up.
Before being output through the air outlet grille (5) the hot air generated in this way is mixed vía
two mixing air flaps with colder room air so that the emitted air does not exceed the maximum
permissible temperature. The position of the mixing air flap and thus the
mixing ratio of the air is controlled by a bi-metal controller.
25
For the Fitter
26
2.2.2 Reducing the Output
A
By moving or removing bridges at the terminals, the connection rating, factory wired to 100 % can
be reduced by three levels (see the table).
The dimensioning of the line cross sections and the fusing should correspond to the maximum
possible output of the unit.
A single-phase connection may be made according to the "Technical connection conditions” of
the energy supply company only up to 2 kW (WSP 2010).
Power 8h heating elements 6h heating element fitting set
variants kW | (series) (special accessory)
Connection M O © @ ® D @ 3 @
variants 100% | 91.6 % | 83.3 % | 75% 100 % || 100 % | 91.6 % | 83.3 % | 75%
Model | |
WSP 2010 2.0 1.83 1.67 1.50 2.0 2.7 2.47 2.25 2.03
WSP 3010 3.0 2.75 2.50 2.25 - 4.1 3.75 3.42 3.07
WSP 4010 4.0 3.66 3.33 3.00 — 5.5 5.04 4.58 4.13
WSP 5010 5.0 4.58 4.16 3.75 — 6.5 5.96 5.42 4.88
WSP 6010 6.0 5.50 5.00 4.50 - 8.1 7.42 6.75 6.08
WSP 7010 7.0 6.42 5.83 5.25 — 9.0 8.24 7.5 6.75
100 % Pure 916%P 83.3 % P ated
(series wiring)
o | E A 1 | | © Mol © ITIL
312] 1|L3IL2{L1] X1 (13 | 2 | 1 |132 | 11| X1 3 | 2} 1 13/12] LI] X1
музой nisl RIA
3/N/PE + 50 Hz 400 V | 3/N/PE + 50 Hz 400 V 3/N/PE - 50 Hz 400 V
75% P 100 % Ps 2kW
| |} À E |
| | | 1 1
9 Malo] rfiahala e © at >| ||) | хо
|3 По: Ч
3/PE ~ 50 Hz 400 V 1/N/PE ~ 50 Hz 230 V
2.3 Rules and Regulations
e Pay attention to the packing slip!
e The national building and garage regulations must be taken into account.
e The installation area must have a sufficient floor load capacity.
In case of doubt a building surveyor should be consulted (for weights of the storage heaters, see
"Technical Data").
e The minimum distance from adjacent object surfaces must be kept (figs. 2 and 2a).
e All electrical connection and installation work must be performed in accordance with the VDE
regulations (0100), the regulations of the electricity supply company responsible and the
pertinent national and regional regulations.
e The device must be disconnectable from the mains at all poles by an supplementary device with a
disconnection distance of at least 3 mm. Contactors, fuses and similar can be connected for this.
e À later increase in the output must be approved separately by the responsible electricity supply
company. Failure to notify the electricity supply company of the increase in the output
constitutes a breach of the electricity supply contract.
e The operating equipment must be designed for the rated consumption of the units.
e The unit's rating plate must be observed!
The specified voltage must match the rated voltage.
e The unit must be fixed to meet the VDE standing safety requirement.
For the Fitter
2.4 Installation Site
A
The unit may not
— be operated in rooms where there is a risk of fire or explosion due to chemicals, dust, gases or
fumes;
- be operated in the immediate vicinity of pipes or containers which carry or contain inflammable
or explosive substances;
- be operated when the minimum distances from adjacent object surfaces are not kept.
In rooms in which exhaust fumes, oil and petrol smells occur, the unpleasant smell may linger and
could possibly cause soiling.
Installation wall |
Check whether a wall of sufficient stability is available for fastening the unit.
If no suitable fastening wall is available, the unit must be fixed to the floor (screwed directly to the
floor or to another floor console [special accessory]).
Floors
The standing surface of the unit must be level and sufficiently stable so that the housing is not
deformed.
A temperature resistance of the fastening wail of at least 85 °C and of the floor of at least 80 °C
must be ensured. The units can be placed on any conventional floor but changes may occur in the
rail area on PVC, parquet and long pile carpeted floors under the influence of pressure and tem-
perature. In this case heat-resistant underlay tiles must be used (to be provided on site).
2.5 Unit Installation (fig. 3-14)
The storage heater must be secured by a wall or floor fixture (fig. 8) to meet the VDE standing
safety requirement.
The screws and plugs necessary for fixing the unit are not included in delivery. They must be
selected and provided by a qualified fitter depending on the respective wall material.
Wall fastening
There is a hole in the unit rear wall in the vicinity of the switching area through which a suitable
screw can be inserted for fixing to a sufficiently stable wall (fig. 8).
Before fixing the unit, make sure that the permissible minimum distances from adjacent objects
are kept. |
Floor fastening
The unit is fixed to the floor by screwing the bottom of the unit to the floor through 4 9 mm holes
(see "Technical Data”, page 9 for dimensions).
This type of fixture is only possible with the air outlet and inlet grilles and the fan drawer removed.
27
English
For the Fitter
28
2.5.1 Unit Installation (fig. 3-6)
e Press the air inlet grille (6) down slightly on both sides, tip forward at the front and remove.
Unscrew both screws at the air outlet grille (5) and remove the grille (fig. 3).
e Loosen the front wall (4) with 2 screws at the bottom (inside threaded holes), lift the front wall
slightly and remove (fig. 4). Loosen the inside front wall with 2 screws at the bottom and remove
(fig. 5).
e Disassembly of the right side wall (3): Remove the rotary knob (a), screw (b) on the side wall (3),
pull the side wall slightly to the side at the back (c), push forward, tilt to the side at the top (d),
lift and remove (fig. 6).
e Feed the power cables and connecting cables for charging control unit and discharge control
unit through the opening in the unit rear wall (15) and connect according to section 2.5.2 (lay
connecting cable about 210 mm and shorten as required so that it does not obstruct the air
vents in the side wall);
e Place the unit at the planned location and screw to the wall (or to the floor if floor fixing is
necessary).
e Remove cover plate (10), cardboard inlays and operating button from inside (fig. 9). This must be
completely free of foreign bodies such as packing leftovers.
Check the thermal insulation in the unit for transportation damage and replace if necessary.
Insert the storage blocks (fig. 10 and 11)
The storage blocks are delivered packed separately.
Storage blocks with slight transportation damage may still be used. This does not impair the
function of the heater.
The heating elements (17) must be lifted slightly to insert the storage blocks (9) (fig. 10).
Place the first storage block with the heating element recess at the top some distance away from
the right thermal insulation under the heater and push to the right and rear thermal insulation.
The elongated holes form the heating channels. |
When lifting the heating elements, make sure that the through holes in the side thermal insulation
are not widened by the heating elements.
Then push the cover plate (10) removed from the interior over the top storage blocks (fig. 12).
2.5.2 Electrical Connection
ON
The heating elements are connected electrically with 3/N/PE ~ 50 Hz 400 V or in the
units WSP 2010 also with 1/N/PE ~ 50 Hz 230 V.
Direct connection with NYM is possible. The number of supply cables and wires as well as cable
cross sections depends on the connection rating of the unit and the type of mains connection and
on special electricity supply company regulations. Observe the appropriate circuit diagrams for
this.
When connecting the unit to an automatic charging control unit, voltages may occur at the
terminals A1/Z1 and A2/Z2 even when the fuses are removed.
Connection
Relieve the strain on the electrical connecting leads as required and connect according to the
electrical circuit diagram in the device (on the inside of the right side pane!) or the connection
diagram.
If the bracket in the switching area for holding the mains terminals is poorly accessible due to too
small a spacing, it can be swung forward during connection work after loosening the screw (not
removing) in the rear panel.
For the Fitter
AN
A bridged must be inserted between "N" and "A2/Z2" for operation with "single-wire control"**!
Power adaptation according to rated charging time
By moving or removing bridges at the terminals, the output can be adapted to the rated charging
time specified by the electricity supply company.
Heating element model 8h (series) 6h (heating element fitting set)
Rated charging time 8h 9h 10h 5h 6h 7h
Connection variants (kW) D @ © © © ®
Model
WSP 2010 2.0 1.83 1.67 2.7 2.47 2.25
WSP 3010 3.0 2.75 2.5 4.1 3.76 3.42
WSP 4010 4.0 3.66 3.33 5.5 5.04 4.58
WSP 5010 5.0 4.58 4.16 6.5 5.36 5.42
WSP 6010 6.0 5.5 5.0 8.1 7.42 6.75
WSP 7010 7.0 6.42 5.83 9.0 8.24 7.5
8h 9h 10h
100 % P
(series ian te 91.6 % P rated 83.3 % Ps
EE LU OL 1 1] LL 1 |
+
© 3 | 2 | 1|L3|L2[L1} X1 © 3} 2] 1|L3|L2|E1| X1 © 3} 2] 1[L3|L2|L1| X1
МА М =n 13 valu
3/N/PE ~ 50 Hz 400 V 3/N/PE ~ 50 Hz 400 V 3/N/PE ~ 50 Hz 400 V
Unit rating plate
Observe the labelling on the rating plate and the circuit diagram!
After connecting electrically, the box corresponding to the connection rating and rated charging
time of the unit on the rating plate and the circuit diagram in these installation instructions
should be marked with a smear-proof ballpoint pen.
2.5.3 Unit Ready for Operation
Cleaning the unit (fig. 13 and 14) |
The open unit must be cleaned after installation and insertion of the storage blocks.
The fans and the air guidance assembly must be removed for this. |
Unscrew and remove the air guidance assembly (16)
e Lift and remove the fan (18) after loosening (not removing) the screws at the front of the
support brackets (pay attention to cable laying).
In some units, the discharge temperature control unit (19) including support plate must be
unscrewed.
Make sure the wires are not damaged when setting down the removed parts.
* Clean the floor plate and fan (avoid damage to lamellas!). Then re-install the fans, possibly the
temperature limiter and the air guidance module (correct cable laying!).
Ciose the unit (fig. 15 and 16)
e Hang in the inside front wall with thermal insutation swung forward slightly at an angle at the
top edge and screw at the bottom edge with 2 screws;
* Hang in the right side wall at the bottom, tilt up, hang in at top and fix with screw: (reverse
order see 2.5.1 - disassembly right side wall fig. 6)
* Hang in front wall at top, swing to the heater at the bottom and fix with 2 screws (always use
the two inside threaded holes) (fig. 15);
e Screw on the air outlet grille, screwing the screws hand tight and then back about 1 turn
(fig. 16);
e Place the air inlet grille at an angle on the lugs in the heater base, swing round at the top and
snap in behind the air outlet grille (fig. 16).
29
30
Connection diagram ...
... for integrated room temperature requlators RTi 100 M/RTi 101 EP
X
FAA xi X1
Ta | LE [IH (IH (LE P NP NP NICNIN EA LT] N
iD
7 г J 7
x |
# Bridges (L) - (L-5H) and [N) - {N]
for control without
remove heater contactor AC .
charging-
E
L
5H
control unit
230 Y system
|| 1
1
|
|
I
| ---
Charging control unit A1/A2 |
1/№ = 50 Hz 230 Y ~~
Lt/L2/L3
(pass. via heating contactor] |
HYPE ~ 50 Hz 400 Y
. .. for wall-mounted room temperature regulators
a X2 X1
N
N
НЧ gol | fee ge |9 | ©
ajo
E == 7
|,
| i
Y Bridges (1) - IL-5H) and LN) - EN]
for control without
remove heater contactor AC
‘ , charging-
| control unit
TA |LE [LA |LH |LE
| 230 V system
|
Charging control unit Al/A2-—
1fH ~ 50 Hz 230 Y
|
wall-mounted room
temperature controtlers —
11/12/13
{poss. via heating contactor)
N/PE - 50 Hz 400 Y
|
|
.. . for single-phase connection (max. 2 kW)
Xi
aa L N LE 3 1 1 u Li Li b
I WJ
UNIPE ~ SO Hz 230V —
... for storage heater replacement “old-new" with wall-mounted
room temperature regulator and missing daytime electricity supply
xi
** "Single wire control”
Charging control unit
room temperature
regulator
L1/L2{L3
(poss. via heating
NfPE ~ 50 Hz 400 V
| LE | 3 1 т В FIR Li db
For the Fitter
For the Fitter
2.6 First-time Operation
2.6.1 Function Test
Check the function of the fan for the storage unit by switching on the room temperature
regulator.
2.6.2 Charging
AN
The units can be started without initial heating up after the function test. Charging takes place
either manually with the adjuster of the mechanical charging control unit or automatically with
the available Elfamatic charging control unit.
During initial charging, the charging in kWh must be determined and compared with the
maximum permissible charging from the cold state specified in the "Technical Data”. The
determined charging may not exceed the maximum permissible charging from the cold state.
During initial charging, a smell may be produced, the room should therefore be adequately aired
(1.5 times air change, e.g. tilted windows). Initial charging in the bedroom should not take place
when sleeping in it if possible.
2.7 Repair, Conversion of Unit
Proceed according to these installation instructions as for the initial installation for re-installation
of a unit which has been dismantled for repairs or which was in operation somewhere else.
In these cases the following must be paid special attention: Parts of the thermal insulation at
~ which there are visible signs or damage or change which could impair the safety must be replaced
by new parts. The insulation must be tested and the rated consumption measured before commis-
sioning.
2.7.1 Conversion of the Unit
The instructions enclosed with the respective fitting set are applicable for conversions, additions
and installations.
2.8 Transfer
Explain the functions of the unit to the user. Draw his attention to the safety instructions in
particular.
Hand over the operating and installation instructions to the user.
«iy
( ) Symbols of the rating plate
AEG (Example WSP 7010)
WSP 7010 357 kg
й a Total weight
E-No. 956 042710 |F-No. 20, 00504
) Charging
IE Discharging
AM Supplementary heater
* tu” 1/N/PE AC 230V 50Hz | A Е
ай
nn
| E а
A 26 W
X
E e C € Made in Germany
31
English
For the Fitter
32
Circuit diagram WSP 2010 - 7010
E1-E6: Heating element (storage heater) || Integr. room temperature regulator
E7: Heating resistor E9: Heating resistor
F1: Safety temperature limiter №: Temperature regulator - discharging
М1 - МЗ: Fan S2: Rocker switch - discharging
N1: Temperature limiter - charging Z1: Radio interference suppressor
№5: Temperature limiter — fan drawer
N4: Temperature limiter - charging [| Supplementary heater
X1: Mains terminal E8: Supplementary heating element
X2: Terminal N2: Temperature regulator - supplementary heater
№: Temperature regulator - supplementary heater
S1: Rocker switch - supplementary heater
В 1 | |
Mi
eg || mon
|
7 : =
Eo
| = A y
e 1 —— +»
| — X | © LT
Na 19 N5 >
a. |
a Le Es be [o] ye
NIT 1 |
= | | Ng Ви
54 HA | | |
|
Dal | |
Na |
3 Y | | 21
№ == 4 |
Mm
Y eg | lz lL |
52 т 7 | Li
| |
yl 000
mT H
| | | |
Na |
|| | |
PE e _ 1
| | sd
||
SA ANA FRS,
AC-signal 230 V
Charging control signal
E
Control circuit
Xi 3 12 [11x L3 |L2 [L1 | X
3/N/PE ~ 50 Hz 400 V
1/N/PE - 50 Hz 230 V
* when external RT is connected
Series circuit
100 % P 91.6 % Ро. 833%P
3 |2 | 11312 |1 312 | 1113112111 3112| 1|L3JL2{LI
J
= |3 plu ТМ Зо L1 | м а | L1
3/N/PE ~ 50 Hz 400V 3/N/PE + 50 Hz 400 Y
3/N/PE ~ 50 Hz 400 V
Only for WSP 2010
75 % Ро 100% P_
3 | 2] 1j13/L2j 11 312] 1|L3|L2|L1
lll Noa
3/PE ~ 50 Hz 400 V 1/N/PE ~ 50 Hz 230 V
For the Fitter
Caution! On a 3/PE AC 50 Hz 230 V mains
Rewiring of the storage heater load circuit necessary!
Circuit diagram for 3/PE AC 50Hz 230 V
Rewiring necessary in the storage heater!
XXX pull off vi wire from E2 and plug to E6
XX pull off br wire from E6 and plug to E4
x pull off ws wire from E4 and plug to E2
>
ws |br |vi
E1 - E6:(storage) heater
F1: protective temperature limiter
N1: temperature limiter - charging
N4: temperature limiter - charging
x1. mains terminal
ws |br |vi ws |br [vi
3 |2 | 1] L3[ 2] Ly
UA
_—
3/PE AC 50 Hz 230V
Jumpers must be wired by customer on site.
English
Environment and recycling
3. Environment and recycling
Please help us to protect the environment by disposing of the packaging in accordance with the
national regulations for waste processing.
Guarantee
For guarantee please refer to the respective terms and conditions of supply for your country.
The installation, electrical connection and first operation of this appliance should be carried out by
a qualified installer.
The company does not accept liability for failure of any goods supplied which are not installed in
accordance with the manufacturer's instructions. |
34
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021