Agilent Technologies 11899A User's Manual

Agilent Technologies 11899A User's Manual
Agilent 11899A
Probe Power Supply
Operating and Service Note
For use with the Agilent Technologies 83400 series lightwave
sources and receivers
© Copyright
Agilent Technologies 2000
All Rights Reserved. Reproduction, adaptation, or translation without prior written
permission is prohibited,
except as allowed under copyright laws.
Agilent Part No. 11899-90004
Printed in USA
April 2000
Agilent Technologies
Lightwave Division
1400 Fountaingrove Parkway
Santa Rosa, CA 95403-1799,
USA
(707) 577-1400
Notice.
The information contained in
this document is subject to
change without notice. Companies, names, and data used
in examples herein are fictitious unless otherwise noted.
Agilent Technologies makes
no warranty of any kind with
regard to this material, including but not limited to, the
implied warranties of merchantability and fitness for a
particular purpose. Agilent
Technologies shall not be liable for errors contained herein
or for incidental or consequential damages in connection with the furnishing,
performance, or use of this
material.
Restricted Rights Legend.
Use, duplication, or disclosure by the U.S. Government
is subject to restrictions as set
forth in subparagraph (c) (1)
(ii) of the Rights in Technical
Data and Computer Software
clause at DFARS 252.227-7013
for DOD agencies, and subparagraphs (c) (1) and (c) (2)
of the Commercial Computer
Software Restricted Rights
clause at FAR 52.227-19 for
other agencies.
Warranty.
This Agilent Technologies
instrument product is warranted against defects in
material and workmanship for
a period of one year from date
of shipment. During the warranty period, Agilent Technologies will, at its option, either
repair or replace products
which prove to be defective.
For warranty service or repair,
this product must be returned
to a service facility designated by Agilent Technologies. Buyer shall prepay
shipping charges to Agilent
Technologies and Agilent
Technologies shall pay shipping charges to return the
product to Buyer. However,
Buyer shall pay all shipping
charges, duties, and taxes for
products returned to Agilent
Technologies from another
country.
Agilent Technologies warrants that its software and
firmware designated by Agilent Technologies for use with
an instrument will execute its
programming instructions
when properly installed on
that instrument. Agilent Technologies does not warrant that
the operation of the instrument, or software, or firmware
will be uninterrupted or errorfree.
Limitation of Warranty.
The foregoing warranty shall
not apply to defects resulting
from improper or inadequate
maintenance by Buyer, Buyersupplied software or interfacing, unauthorized modification or misuse, operation
outside of the environmental
specifications for the product,
or improper site preparation
or maintenance.
No other warranty is
expressed or implied. Agilent
Technologies specifically disclaims the implied warranties
of merchantability and fitness
for a particular purpose.
Exclusive Remedies.
The remedies provided herein
are buyer's sole and exclusive
remedies. Agilent Technolo-
2
❍ The OFF symbols
are used to mark the
positions of the instrument power line
switch.
gies shall not be liable for any
direct, indirect, special, incidental, or consequential damages, whether based on
contract, tort, or any other
legal theory.
The CE mark is a registered trademark of
the European Community.
Safety Symbols.
CAUTION
The caution sign denotes a
hazard. It calls attention to a
procedure which, if not correctly performed or adhered
to, could result in damage to
or destruction of the product.
Do not proceed beyond a caution sign until the indicated
conditions are fully understood and met.
The CSA mark is a registered trademark of
the Canadian Standards Association.
The C-Tick mark is a
registered trademark
of the Australian Spectrum Management
Agency.
WARNING
The warning sign denotes a
hazard. It calls attention to a
procedure which, if not correctly performed or adhered
to, could result in injury or
loss of life. Do not proceed
beyond a warning sign until
the indicated conditions are
fully understood and met.
The instruction manual symbol. The product is marked with this
warning symbol when
it is necessary for the
user to refer to the
instructions in the
manual.
The laser radiation
symbol. This warning
symbol is marked on
products which have a
laser output.
The AC symbol is used
to indicate the
required nature of the
line module input
power.
| The ON symbols are
used to mark the positions of the instrument
power line switch.
ISM1-A
This text denotes the
instrument is an
Industrial Scientific
and Medical Group 1
Class A product.
Typographical Conventions.
The following conventions are
used in this book:
Key type for keys or text
located on the keyboard or
instrument.
Softkey type for key names that
are displayed on the instrument’s screen.
Display type for words or
characters displayed on the
computer’s screen or instrument’s display.
User type for words or charac-
ters that you type or enter.
Emphasis type for words or
characters that emphasize
some point or that are used as
place holders for text that you
type.
General Safety Considerations
General Safety Considerations
This product has been designed and tested in accordance with IEC Publication 61010-1, Safety Requirements for Electrical Equipment for Measurement,
Control and Laboratory Use, and has been supplied in a safe condition. The
instruction documentation contains information and warnings that must be
followed by the user to ensure safe operation and to maintain the product in a
safe condition.
WARNING
There are many points in the instrument which can, if contacted, cause
personal injury. Be extremely careful. Any adjustments or service
procedures that require operation of the instrument with protective
covers removed should be performed only by trained service
personnel.
WARNING
These servicing instructions are for use by qualified personnel only.
To avoid electrical shock, do not perform any servicing unless you are
qualified to do so.
WARNING
The opening of covers or removal of parts is likely to expose
dangerous voltages. Disconnect the Agilent 11899A from all voltage
sources while it is being opened.
WARNING
The power cords on system instruments are connected to internal
capacitors that may remain live for five seconds after disconnecting
the plug from its power supply.
WARNING
If this instrument is not used as specified, the protection provided by
the equipment could be impaired. This instrument must be used in a
normal condition (in which all means for protection are intact) only.
WARNING
To prevent electrical shock, disconnect the Agilent 11899A from
mains before cleaning. Use a dry cloth or one slightly dampened with
water to clean the external case parts. Do not attempt to clean
internally.
3
General Safety Considerations
WARNING
This is a Safety Class 1 product (provided with a protective earthing
ground incorporated in the power cord). The mains plug shall only be
inserted in a socket outlet provided with a protective earth contact.
Any interruption of the protective conductor inside or outside of the
product is likely to make the product dangerous. Intentional
interruption is prohibited.
WARNING
No operator serviceable parts inside. Refer servicing to qualified
personnel. To prevent electrical shock, do not remove covers.
WARNING
For continued protection against fire hazard, replace line fuse only
with same type and ratings, (type T 0.315A/250V for 100/120V
operation and 0.16A/250V for 220/240V operation). The use of other
fuses or materials is prohibited. Verify that the value of the linevoltage fuse is correct.
• For 100/120V operation, use an IEC 127 5×20 mm, 0.315 A, 250 V, Agilent
part number 2110-0449.
• For 220/240V operation, use an IEC 127 5×20 mm, 0.16 A, 250 V, Agilent
Technologies part number 2110-0448.
CAUTION
Before switching on this instrument, make sure that the line voltage selector
switch is set to the line voltage of the power supply and the correct fuse is
installed. Assure the supply voltage is in the specified range.
CAUTION
This product is designed for use in Installation Category II and Pollution
Degree 2 per IEC 1010 and 664 respectively.
CAUTION
VENTILATION REQUIREMENTS: When installing the product in a cabinet, the
convection into and out of the product must not be restricted. The ambient
temperature (outside the cabinet) must be less than the maximum operating
temperature of the product by 4°C for every 100 watts dissipated in the
cabinet. If the total power dissipated in the cabinet is greater than 800 watts,
then forced convection must be used.
CAUTION
Always use the three-prong ac power cord supplied with this instrument.
Failure to ensure adequate earth grounding by not using this cord may cause
instrument damage.
CAUTION
Do not connect ac power until you have verified the line voltage is correct.
Damage to the equipment could result.
4
General Safety Considerations
CAUTION
This instrument has autoranging line voltage input. Be sure the supply voltage
is within the specified range.
5
Contents
Contents
The Agilent 11899A Probe Power Supply— At a Glance
Performance Characteristics 9
Power Cords 10
Returning the Instrument for Service 12
Agilent Technologies Service Offices 15
6
7
The Agilent 11899A Probe Power Supply— At a Glance
The Agilent 11899A Probe Power Supply—
At a Glance
The Agilent 11899A probe power supply provides regulated DC power at the
front panel receptacles for operation of one or two probes. The following products are compatible with the power supply:
• Agilent 85024A High Frequency Probe
• Agilent 41800A Active Probe
• Agilent 834XX family of lightwave sources and receivers
One of the following options is required for operation in a particular country:
• Option 100 for 100 volt operation
• Option 120 for 120 volt operation
• Option 220 for 220 volt operation
• Option 240 for 240 volt operation
7
The Agilent 11899A Probe Power Supply— At a Glance
An extender cord (Agilent 10131B) can also be ordered to increase the length
between the power supply and the probe.
This manual provides operating and service information for the probe power
supply. Perform all work at a static-safe workstation. Failure to protect against
electrostatic discharge could result in damage to the instrument. For information on static-safe workstations and protection against electrostatic discharge,
refer to the User’s Guide for your Agilent Technologies 83400 series product.
8
Performance Characteristics
Performance Characteristics
The following table contains performance characteristics for the
Agilent 11899A probe power supply. These are not specifications, but are provided as information useful in operating the power supply.
Probe Driving Capability
1 or 2 probes
Power Output
–12.6 volts 350 mA; and +15 volts 500 mA (male connectors)
Power Input
88–112 volts, 50/60 Hz (option 100)
105–135 volts, 50/60 Hz (option 120)
193–247 volts, 50/60 Hz (option 220)
211–269 volts, 50/60 Hz (option 240)
Dimensions
81 mm wide, 65 mm high, 121 mm long (3.2 in × 2.6 in × 4.8 in)
Weight
net 0.9 kg (2 lb); shipping 1.8 kg (4 lb)
9
Power Cords
Power Cords
Plug Type
Cable Part
No.
Plug Description
Length
(in/cm)
Color
Country
250V
8120-1351
Straight *BS1363A
90/228
Gray
8120-1703
90°
90/228
Mint Gray
United Kingdom,
Cyprus, Nigeria,
Zimbabwe,
Singapore
8120-1369
Straight *NZSS198/ASC
79/200
Gray
87/221
Mint Gray
250V
90°
8120-0696
250V
125V
250V
Australia, New
Zealand
8120-1689
Straight *CEE7-Y11
79/200
Mint Gray
East and West
Europe, Saudi
Arabia, So. Africa,
India (unpolarized
in many nations)
8120-1692
90°
79/200
Mint Gray
8120-2857p
Straight (Shielded)
79/200
Coco Brown
8120-1378
Straight *NEMA5-15P
90/228
Jade Gray
8120-1521
90°
90/228
Jade Gray
8120-1992
Straight (Medical) UL544
96/244
Black
United States,
Canada, Mexico,
Philippines,
Taiwan
8120-2104
Straight *SEV1011
79/200
Mint Gray
Switzerland
8120-2296
1959-24507
79/200
Mint Gray
Type 12 90°
* Part number shown for plug is the industry identifier for the plug only. Number shown for
cable is the Agilent Technologies part number for the complete cable including the plug.
10
Power Cords
Plug Type
Cable Part
No.
Plug Description
Length
(in/cm)
Color
Country
220V
8120-2956
Straight *DHCK107
79/200
Mint Gray
Denmark
8120-2957
90°
79/200
Mint Gray
8120-4211
Straight SABS164
79/200
Jade Gray
8120-4600
90°
79/200
250V
Republic of South
Africa
India
100V
8120-4753
Straight MITI
90/230
8120-4754
90°
90/230
Dark Gray
Japan
* Part number shown for plug is the industry identifier for the plug only. Number shown for
cable is the Agilent Technologies part number for the complete cable including the plug.
11
Returning the Instrument for Service
Returning the Instrument for Service
The instructions in this section show you how to properly return the instrument for repair or calibration. Always call the Agilent Technologies Instrument
Support Center first to initiate service before returning your instrument to a
service office. This ensures that the repair (or calibration) can be properly
tracked and that your instrument will be returned to you as quickly as possible. Call this number regardless of where you are located. Refer to “Agilent
Technologies Service Offices” on page 15 for a list of service offices.
Agilent Technologies Instrument Support Center . . . . . . . . . . . (800) 403-0801
If the instrument is still under warranty or is covered by an Agilent Technologies maintenance contract, it will be repaired under the terms of the warranty
or contract (the warranty is at the front of this manual). If the instrument is
no longer under warranty or is not covered by an Agilent Technologies maintenance plan, Agilent Technologies will notify you of the cost of the repair after
examining the unit.
When an instrument is returned to a Agilent Technologies service office for
servicing, it must be adequately packaged and have a complete description of
the failure symptoms attached. When describing the failure, please be as specific as possible about the nature of the problem. Include copies of additional
failure information (such as the instrument failure settings, data related to
instrument failure, and error messages) along with the instrument being
returned.
Preparing the instrument for shipping
1 Write a complete description of the failure and attach it to the instrument.
Include any specific performance details related to the problem. The following
12
Returning the Instrument for Service
information should be returned with the instrument.
• Type of service required.
• Date instrument was returned for repair.
• Description of the problem:
• Whether problem is constant or intermittent.
• Whether instrument is temperature-sensitive.
• Whether instrument is vibration-sensitive.
• Instrument settings required to reproduce the problem.
• Performance data.
• Company name and return address.
• Name and phone number of technical contact person.
• Model number of returned instrument.
• Full serial number of returned instrument.
• List of any accessories returned with instrument.
2 Cover all front or rear-panel connectors that were originally covered when you
first received the instrument.
CAUTION
Cover electrical connectors to protect sensitive components from electrostatic
damage. Cover optical connectors to protect them from damage due to physical
contact or dust.
CAUTION
Instrument damage can result from using packaging materials other than the
original materials. Never use styrene pellets as packaging material. They do not
adequately cushion the instrument or prevent it from shifting in the carton.
They may also cause instrument damage by generating static electricity.
3 Pack the instrument in the original shipping containers. Original materials are
available through any Agilent Technologies office. Or, use the following
guidelines:
• Wrap the instrument in antistatic plastic to reduce the possibility of damage
caused by electrostatic discharge.
• For instruments weighing less than 54 kg (120 lb), use a double-walled, corrugated cardboard carton of 159 kg (350 lb) test strength.
• The carton must be large enough to allow approximately 7 cm (3 inches) on
all sides of the instrument for packing material, and strong enough to accommodate the weight of the instrument.
• Surround the equipment with approximately 7 cm (3 inches) of packing material, to protect the instrument and prevent it from moving in the carton. If
packing foam is not available, the best alternative is S.D-240 Air Cap™ from
13
Returning the Instrument for Service
Sealed Air Corporation (Commerce, California 90001). Air Cap looks like a
plastic sheet filled with air bubbles. Use the pink (antistatic) Air Cap™ to
reduce static electricity. Wrapping the instrument several times in this material will protect the instrument and prevent it from moving in the carton.
4 Seal the carton with strong nylon adhesive tape.
5 Mark the carton “FRAGILE, HANDLE WITH CARE”.
6 Retain copies of all shipping papers.
14
Agilent Technologies Service Offices
Agilent Technologies Service Offices
Before returning an instrument for service, call the Agilent Technologies
Instrument Support Center at (800) 403-0801, visit the Test and Measurement
Web Sites by Country page at http://www.tm.agilent.com/tmo/country/English/
index.html, or call one of the numbers listed below.
Agilent Technologies Service Numbers
Austria
01/25125-7171
Belgium
32-2-778.37.71
Brazil
(11) 7297-8600
China
86 10 6261 3819
Denmark
45 99 12 88
Finland
358-10-855-2360
France
01.69.82.66.66
Germany
0180/524-6330
India
080-34 35788
Italy
+39 02 9212 2701
Ireland
01 615 8222
Japan
(81)-426-56-7832
Korea
82/2-3770-0419
Mexico
(5) 258-4826
Netherlands
020-547 6463
Norway
22 73 57 59
Russia
+7-095-797-3930
Spain
(34/91) 631 1213
Sweden
08-5064 8700
Switzerland
(01) 735 7200
United Kingdom
01 344 366666
United States and Canada
(800) 403-0801
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement