Aiphone AP-1M User's Manual

Aiphone AP-1M User's Manual
83599800 1096 (A) <» А!РНОМЕ
AP-M Series
HIGH-POWER INTERCOM
~
N
— PRECAUTIONS on AP-M SYSTEM
A Precautions on Safety
А © № >
2.
3.
4.
AP-1M, 1-call master
Models: AP-5M, 5-call master
AP-10M, 10-call master Type A: 230V AC version
INSTALLATION MANUAL
The AP-M equipment is an electrical device, whose wiring must be done by qualified personnel.
Do not change or modify AP-M equipment.
Keep AP-M station away from water or any other liquid. It can cause fire or electric shock.
Do not open AP-M station. High voltage is present inside.
General Precautions
1.
Do not install or make any wire terminations while power supply is turned on.
It can cause electric shock or damage the unit.
Do not install AP-M components in any of the following locations, as it may cause the system to malfunction:
— High or extreme cold temperature areas: under direct sunlight, near equipment that varies in
temperature, in front of air-conditioner, inside a refrigerated area, etc.
— Places subject to moisture or humidity extremes.
— Places subject to environmental conditions, such as oil, dust, chemicals, salt, etc.
— Places subject to constant vibration or impact.
Make sure wires are connected properly before plugging in the unit.
When mounting AP-M station on wall, select a location where protruded unit would not cause injury to
people.
Precautions on Usage
1.
2.
AP-M system is not operable during a power failure.
In areas where broadcasting station antennas are close by, intercom system may be affected by radio
frequency interference.
Keep all DC wiring at least 30cm, 20” away from AC 100 ~ 240V wiring, fluorescent lighting, or dimmer
switches. Cross AC wiring at a 90° angle.
Severe weather conditions, such as lightning storms, may cause damage to AP-M equipment. The AP-M
has a GROUND terminal, which is to be connected to an earth ground.
1 SYSTEM OUTLINE & COMPONENTS
AP-M is a High-Power Intercom with 10 watt power output.
system in combination with remote 8Q horn speakers and Aiphone’s subs, desk or ceiling mount.
Xx Use a twisted pair cable for each sub (non-polarized).
80 Horn
H Package contents
It can be configured in either single or dual master
For any 8Q horn speaker, install a NP 25mfd, 25V capactior in line with * Master station (AP-1M, AP-5M or
# wire (not required when NP-B is installed) AP-10M)
¢ Mounting bracket
* Packet of screws
* Installation 8% Operation Manual
E Components available
* Master stations * Sub stations
Wall/desk Ceiling mount
AP-1M, AP-5M, AP-10M,
1-call master 5-call master 10-call master
AS-3WA,
Dual call
NP-B,
Call button
* Mounting accessories: N-EA: Frame for AS-3N, ceiling surface-mount
NBZ-M: Ceiling flush-mount
NP-W: Surface-mount box for NP-B
£ NAMES AND FEATURES -
15 Speaker
OFF button
Station selector button
Call-in LED
Directory card
Power on LED
Power switch
Mic.
RECEIVE volume control
. TRANSMIT volume control
. Tone CALL button
. TALK/LISTEN button
. Occupied LED
. AC cord / plug
. Preset receive & transmit volume controls
* AP-5M: Second switch bank is not included.
О 0 м о о В О
LL A A A A
a RN =0"
10 1112
E Features
* One or two master configuration * 8Q horn speaker w/talkback
1,5, or 10-call master consoles e Separate transmit & receive volume controls
* 10 watt output Group call (selectively up to 5 subs)
* Desk/wall or ceiling subs available
11
10 I |
Г
—
Speaker
Power on LED
Power switch
Mic.
RECEIVE volume control
TRANSMIT volume control
OFF button
TALK/LISTEN button
Communication LED
AC cord/plug
Preset receive & transmit volume controls
5 CONDON
— ©
C
mr ©
AP-1M
45 6 7 8
M Features
Same features as on AP-10M, except for single sub call capability.
Sy,
Terminal Preset volume
block controls
Y
« AP-5M terminals
E Terminal block layout
1-5
6-10
AP-5M, AP-10M
As shown, station numbers 1 ~ 5 (top row) & 6 ~ 10 (2nd row)
are assigned, corresponding to the terminal numbers.
N Cable
1 ~50r1~ 10: Selective communication channels
E: Common communication
C: “CALL” for calling other master
R : Occupied mode control
GND : for grounding
Use a single-twisted pair cable for wiring between AP-M and each sub, homerun, or the other AP-M (In USA,
cable # 832202 specified)
Hl Wiring
In single-master configuration, wiring is non-polarized for any type of sub. In dual-master system, wiring of
common sub(s), AS-3WA (2-call) and AP-M’s becomes polarized.
E 82 horn speaker
When using an 8Q horn speaker and a call button is not required,
insert a 25 mfd non-polar capacitor in one side of the line. If a 25 mfd
capacitor is not available, two 50 mfd, 25V electrolytic capacitors may
be used when connected in series + to +, or — to —, as shown.
HE Wiring examples of NP-B call buttons
For AS-3N
1. Multiple NP-B's
To AP-M XX e e
Red(2) à +
Making non-polar capacitor:
25mfd, 25V using two NP 50mfd, 25V
2. Locai call switch
To AP-M 000€ = ©
O
ТИ <
7
——
Call button
For 8Q horn
1. Multiple NP-B's
Blue(2)
NP-B NP-B NP-B
2. Local call switch
25uF NP,25V
To AP-M XX Ç
1W<
07
——
Call button
Ш
Ш WIRING DIAGRAMS
e AP-5M, AP-10M
AP-10M
Polarized NP 4
1 1
CO E Sw —— E AS-3A
> Polarized =} о NP 2
LE] LE] E AS-3A
Polarized NP
3 3 3
[3] © 200 ГЕ] 3000 Е < AS-3A
Polarized 25uF NP,25V
[4] 2000 E 0 "E С 4
[LE] LE} o tb 8Q horn
Polari
[5] olarized — [51 q 5
LE} XX {EJ > 80 horn
NP-B
6 7 5 25uF NP,25V NP 5] EH NP 25uF NP,25V 7 6
80 nom EP) fn OC [E] [E] ХХ a XJ 80 hor
NP
7 =~ [Гб [7] 7
AS-3N od XX [E] [E] AS-3N
NP
8 5 [8] 8
AS-3N ol XOX ГЕ] [E] AS-3N
Polarized
[9]
XX ГЕ)
9
00 E
Polarized LE]
Polarized ГО]
© [El LE]
Master to master
communication 1101 [E] XX ГЕ]
[8] ГВ] No. of E terminals : 6 on AP-5M.7 on AP-10M
(Multiple “E” wires can be connected to one E terminal.)
- AP-1M
MOUNTING
> 80 horn
AP-M Terminals
Gang Box
Sub Chassis
AP-M is designed for desk-top use. For wall-mounting,
install sub-chassis upside down.
Do not remove sub-chassis, which is necessary for heat
radiation. Use a sub-plate for mounting on box.
AS-3A, AS-3WA a
Terminals — 97900 Вох
8 83.5mm
= (3-5/16")
Bracket
2 SCrews
Supplied
Attach the mounting bracket to box or wall. Mount the unit
on the bracket until it firmly locks.
AS-3N Holder
Ceiling
diameter
{5-7/8")
| 5——— NBZ-M FRAME
(attach to speaker)
Open a hole 150mme (5-7/8"g) in the ceiling. (NBZ-M square frame may be
attached from the back). Locate the holder on the ceiling, and mount AS-3N
with 2 hooks.
* For surface-mounting, use N-EA round frame.
NP-B Sinal b
Panel- ne gang ох Screws (2)
mounting Screws (2) Is
screws (2) E
= 83.56mm
:- (3-5/16") a
e Ss
Panel
screw (2)
NP-B cail switch flush-mounts to box, or surface-mounts on NP-W box.
—4—
3 OPERATIONS on AP-M
OFF
Station selector
button
Speaker
Mic. Cail-in LED
Power on LED
Power switch
Occupied LED
TALK/LISTEN button
CALL button
Hl Placing a call to sub
1. Depress the station selector button of sub.
2. Depress CALL button to ring sub with mono tone.
Or press TALK button and call with voice.
3. Release TALK button to listen.
Press TALK button to reply.
4. At conclusion, depress OFF button.
Ш Receiving a sub call-in
Monotone sounds, and a call-in LED is lit for 15 sec.
Depress the LED lit station selector button.
Press TALK button to talk and release to listen.
At conclusion, depress OFF button.
PON
* A call-in from sub during communication is indicated by a lit LED only.
E Group Call (up to 5 subs)
1. Depress up to 5 station selector buttons.
2. Depress and hold down TALK button to transmit.
3. Depress OFF button(s) to reset.
E Communication between AP-M's
The other AP-M calls in with tone or with voice direct.
Depress the other master’s selector button. Initiating master uses TALK button to talk, and release to
listen.
E Volume adjustments
On front panel, set speech volumes as desired. = = " Е
Replace to MID levels at end of each communication. yy
RECEIVE vol. , 3-position
TRANSMIT vol. , 3-position RECEIVE - VOL - TRANSMIT
H Sub stations: AS-3A, AS-3WA, 82 horn
To call, depress momentarily CALL button on AS-3A sub (either on AS-3WA) or on NP-B. lt rings
AP-M master with monotone, and an LED is lit for approx. 15 seconds. Master calls in with tone
and/or voice directly. Just reply toward the unit hands free.
E Operations on AP-1M
To call a sub with tone, press both
OFF and TALK buttons. Or press Speaker
TALK and call by voice.
Continue communications with TALK Mic.
button. I Power on LED Communication
When finished, depress OFF button. Power switch TALK/LISTEN button
OFF button
* Temperature:
TECHNICAL PRECAUTIONS
AP-M is rated to operate between temperatures 0°C ~ +40°C (+32°F ~ +104°F).
* Power switch:
If AP-M is unplugged or its power switch is turned off, it cannot receive sub’s call nor transmit a call to subs. However, it can receive the other
AP-M’s call-in tone and voice.
* Volume adjustments on back panel
Place two front controls to MID position and adjust volume to desired level with
controls on back panel.
* Cleaning:
Clean AP-M equipment with a soft cloth dampened with neutral household cleanser.
Never use any abrasive cleaner or cloth.
TERE
та
uli
* Power source:
* Power consumption:
* Communication output:
* Calling & communication:
* Wiring:
* Distance:
e Dimensions & weight:
+
eto eto slo ojo efe aja ato efe aja ado ajo ajo ajo aja ajo ojo ojo ojo ojo alo ajo efe ajo ato aja ato eto efe ota ojo fe eta ajo ajo aja ato ato ato ato aja efa aja efo aja ato af efe ato ato ate alo ato eto eto ojo ojo efe nto to efe cto ate ade
AIPHONE CO., Ltd., Nagoya, Japan
AIPHONE CORPORATION, Bellevue, WA, USA
AIPHONE EUROPE NV, Antwerp, Belgium
AP-M-I/M(E)1096A
£ SPECIFICATIONS (AP-M)
BACK VIEW
VOL. VOL.
a Y /*
D H D,
110 - 125V AC, 127V AC, 220-240V AC, 50/60 Hz (AP-M). 230V AC, 50/60Hz (AP-M/A).
Max. 45W, 4W standby (AP-M, AP-M/A).
AP-M to sub 10 watts max.
AP-M to AP-M 0.3watts max.
Sub to AP-M 0.3watts max.
Sub’s call-in with mono tone & an LED lit for 15 sec. (tone only on AP-1M). Select and press to
talk and release to listen. Speak hands free at sub.
The other AP-M calls by voice. Reply hands free.
Twisted pair cable (In USA,1 pair #832202 per station, specified).
1 pair per sub (any type). 2 pairs + 1 between AP-M's.
Between AP-M to sub/AP-M;
Diameter/AWG | 0.65mmg | 1.0mme | 22AWG | 18AWG
Distance 150m 360m 490’ 1,200
Desk use; |
AP-1M; 240H x 196W x 114D (mm). 9-1/2"H x 7-3/4"W x 4-1/2"D.
AP-5M, 10M: 253H x 276W x 140D (mm). 10”H x 11”W x 5-1/2"D.
AP-1M: 3.2Kg (7.05 Ibs.) AP-5M: 4.0Kg (8.82 Ibs.) AP-10M: 4.2Kg (9.26 Ibs.) approx.
WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one
year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which
examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision
whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or aitered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
wie sie vie ojo ojo edo ojo slo slo ole slr ole slo ole lv ojo ajo ode ole ole ojo ojo aja ole ojo jo ojo ajo ajo ojo ajo ajo efe oe ojo ojo eto eto ola ajo jo eto eta ajo ojo aja ole oe oho ofa ole ojo aja ajo ojo ajo ole ole oe ajo ato fo ato
4h de de dde dede ef fe fe ff dd
a COMMUNICATION SYSTEMS
HOME, BUSINESS, INDUSTRY.
Printed in Japan (E)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement