Aiphone KB-3HRD User's Manual

Aiphone KB-3HRD User's Manual
830762 (E) P0212 AF 54192 Al PHON E
VIDEO SENTRY COLOR TILT
COLOR TILT VIDEO ENTRY SECURITY INTERCOM
Models: KB-3MR D, Master station with monitor
KB-3 HR D, Sub station with monitor
INSTALLATION MANUAL
This Manual and the Markings on the product contain
various symbols in order that the product can be used
safely and properly, and that the installer and user are
protected from injury and property damage.
The following precautions must be thoroughly read and
understood before proceeding. КН
PRECAUTIONS ON INSTALLATION & WIRING
/\ WARNING Negligence could result in death or serious injury.
/\ CAUTION Negligence could result in injury or damage to property.
The following precautions also apply to KB-3HRD sub station with monitor.
A WARNING 1. Do not connect any power source other than specified to terminals +, — on KB-3MRD. ®
Fire or damage to the unit could result.
. Do not open KB-3MRD. High voltage is present inside, and it can cause electric shock. ®
. Do not change or alter KB-3MRD. It can cause fire or electric shock.
. Make sure wires are connected properly before plugging in power supply. ®
. Keep the KB-3MRD unit away from water or any other liquid. Fire or electric Y
shock could result.
. Do not put any forcible strength on the video monitor. Damage may result. O
. Keep AC plug away from moisture or dust.
. Keep AC cord away from being marred or crushed. O
. Do not plug or unplug with wet hands.
. Do not put any metal into KB-3MRD through openings. It can cause fire, CS
electric shock or unit damage.
с! > о
O ONO
AN CAUTION 1. Do not install or make any wire terminations while power supply is plugged in. O
It can cause electrical shock or damage to the unit.
. Do not manually hold down hook switch to verify chime volume. It sounds very O
loud in the handset, and can cause hearing damage.
. Mount KB-3MRD on wall in a convenient location, but not where it could be
bumped or jarred.
. In case of electrical storms, unplug power supply from AC outlet. It can cause O
fire, electric shock, or power surge damage.
. Do not install KB-3MRD components in any of the following locations, as it may S
cause the system to malfunction;
— High or extreme cold temperature area: under direct sunlight, near equipment
that varies in temperature, in front of air conditioner, inside a refrigerated area, etc.
— Places subject to moisture or humidity extremes. (bathroom, cellar, greenhouse, etc.) Y
— Places subject to environmental conditions, such as oil, dust, chemicals, salt, etc.
— Places subject to constant vibration or impact.
— Places where noise generating devices such as TV or radio are close by.
a > o N
/ÍN GENERAL PRECAUTIONS
1. KB-3MRD equipment, except for KB-DAR, is designed for indoor use only.
Do not install outdoors.
2. KB-3MRD system is not operational during a power failure.
3. In areas where broadcasting station antennas are close by, intercom system
may be affected by radio frequency interference.
4. Keep all DC wiring at least 30cm(1') away from AC 100~240V wiring, fluorescent
lighting, or dimmer switches. Otherwise, cross AC wiring at a 90°angle.
Examples of Symbols;
/N GENERAL PRECAUTIONS: — ZA mark
indicates caution statement (incl. danger
and warning), which is specifically
shown inside.
O
GENERAL INSTRUCTIONS: — @ mark
indicates contents which demands a
specific action shown inside or attached.
GENERAL PROHIBITIONS: — O mark
indicates contents which prohibit a specific
action shown inside or attached.
® DISMANTLE PROHIBITIONS
Y MOISTURE PROHIBITIONS
1 SYSTEM OUTLINE & COMPONENTS
VIDEO SENTRY COLOR TILT 3 - 5: KB-3MRD is an audio video entry
security intercom for 3 video doors & max. 5 room stations with monitor.
SYSTEM LAYOUT
KB-DAR
Video door
station
IF-DA
Door station
KB-3MRD, Master
station w/monitor
KB-3HRD, Sub
station w/monitor
PACKAGE CONTENTS
e Master 8 sub stations w/monitor
(KB-3MRD or KB-3HRD)
* Packet of screws
* Connectors (2) for options
(with KB-3MRD)
e Installation & Operation Manual
Upon completing installation, give the
Operation Manual to the user.
KB-3HRD
24 2/1
24
I= : PS-2420, PS-2420D, PS-2420S, PS-2420UL
One I= for KB-3MRD, RY-3DL
One LEVI per two KB-3HRD's
: AC transformer PT-1210N in North America
KB-DAR: Video door station.
KB-3MRD: Master station w/monitor.
KB-3HRD: Sub station w/monitor (1 ~ 4 pcs).
KB-3SD: Audio sub station (max. 2).
Door station (IE/IF series).
Functions
One to KB-3MRD master only
Requires an AC transformer
(PT-1210N in North America)
Max. 60 image memory. 18V
or 24V DC power sourced.
External light turns on when
KB-DAR call button or inside
monitor button is pressed.
1-gang surface mounting.
1-gang surface mounting.
IF-DA:
KB-3SD, Audio
sub station
24V DC power supply:
PS-2420, PS-2420D,
PS-2420S, PS-2420UL
OPTIONAL COMPONENTS
Model Description
IER-2 Call extension speaker
EL-12S Electric door release.
12V AC, 0.125A
12V DC, 0.2A
KC-32EU | Picture memory unit.
MAW-B | Auxiliary light control
relay. 24V DC.
KAW-D | 30° Angle Box for KB-DAR
KA-DGR | Stainless steel panel
PANEL for KB-DAR
RY-3DL | Door release adaptor
1-gang surface mounting.
-2.
KB-3HRD
2 NAMES & FEATURES
KB-DAR
White light — | |_—— Color CCD camera
— Mic.
Speaker — ——
7 — CALL button
Tamper-proof
screw/cover
KB-3MRD
Handset
| | —Video monitor (TFT color LCD)
Station selector
button || — Door release button
Speaker _— Door call-in LED 1, 2, 3
—— MONITOR button
Instantly turns on audio & video of door,
to monitor handsfree, or to extend while
| Е communicating.
Mic.
Tilt control button
Move door camera vertically from 0°
to max. 40° (approx.).
ALL CALL button
Also, works for setting PRIVACY mode.
Left side / Bottom view
TT /
CP FT
moe 7 +
LL LL
TONE control button
Adjusts chime tone &
receive volumes.
\
+0 65 № |
Y3MOd
power switch
. BRIGHT control MONITOR:
AN Turn power switch off when system Adjust audio monitor volume of door.
malfunctions. Can be cut off: OFF — MID — HIGH.
FEATURES
* Audio video entry security intercom 3 doors - 5 room stations with monitor with TILT camera control.
* Clear and bright image with TFT(*1) Color LCD monitor and DSP(*2) for door station.
* INSTANT - ON audio and video of door station when door calls or during monitoring from room station.
* Selective room calling with handsfree reply at called station.
* ALL CALL button.
* Selective door release control with RY-3DL adaptor.
* Max. 100m distance to farthest sub station w/monitor. (*1) TFT = Thin Film Transistor
See power supply requirements. (*2) DSP = Digital Signal Processor
3
INSTALLATION
Cable Specify for wiring to both door and inside stations.
1. 0.65mmo to 1.2mmo (22AWG to 16AWG).
2. PE (polyethylene) insulation & Vinyl-sheathed cable.
Attenuation of less than — 6.5dB at 10MHz./100m, 330" length.
3. Solid core conductor. (Note: Do not use stranded wire on this system.)
4. Line impedance : + 75Q (less than 100Q at the highest).
For other types, normal operation or max. communication distance cannot be guaranteed.
Wiring
1. Use a parallel cable to connect video door station. Do not use any other cable YES NEVER
like coax-cable, individual wires, etc. ad
2. When existing chime wires are used, be sure to locate and disconnect the AC a
transformer. When system does not function properly, install new cable as PARALLEL WIRE COAXIAL CABLE
KB-DAR KB-MRD TKB-3HRD KB-3HRD
specified.
If unused wires exist in the cable, terminate each extra pair with a 120Q
resistor at each end of wires (on audio sub station end as well). Extra wires can
interfere with video signal.
Keep audio/video wires more than 30cm(1") away from AC 100~240V power
lines. It will cause noise in communication & malfunction.
Run internal wiring of audio/video system in such a manner that the cable is
run from master to sub without any splices, which will create inferior video KB-DAR KB-3MRD
quality. or KB-3MRD or KB-3HRD
YES NEVER
Wire monitor to monitor Homerun to master DO NOT include in & out wires in
the same jacketed cable.
KB-3HRD KB-3HRD
KB-DAR KB-3MRD 7
Tol] 2 [|
KB-DAR
To 2
|
||
NOTE: The above wiring methods also apply to KB-3SD audio sub station.
Power supply requirements
METHOD 1 METHOD 2 100m w/1.0mmgo
| — 1 ; —— T
330' wi8AWG
100m w/1.0mmo 50m w/1.0mmo
— — ' — — — — — —
| 330' w/18AWG 165' WI8AWG
KB-3MRD KB-3HRD KB-3HRD KB-3HRD KB-3HRD KB-3MRD KB-3HRD KB-3HRD
=
J,
т
10m w/1.0mmo
33' WI8AWG
1
Л Use a specified power supply to secure proper operations of system.
A Do not connect power supplies in parallel. PS
=) NEVER
Compatibility
Description Compatible Not compatible
Video door station KB-DAR KC-DAR, KA-DAR, others
Sub station w/monitor | KB-3HRD KC-1HRD
Audio sub station KB-3SD KC-1SD, IEH-1CD, others
-4-
3 INSTALLATION (continued)
Mounting locations & Height
Do not install a video door station in the following
locations;
— Places subject to temperature/humidity extremes.
— Places from dust, vapor, smoke and chemicals.
— Places where a call is strongly backlit (white wall
is on the background).
— Places where direct sunlight or strong light comes
into the camera lens.
Image view area (approx.) when the door camera is tilted Mount the station so that the video
*2350m . monitor comes at the user's eye level.
VERTICAL (tilting) 79" = HORIZONTAL
*124ст Over view Unit _ _
(4'1 ")
*111cm -
(3'8")
Setting
Video door station Room stations w/monitor
Mounting locations
7
\
center
150cm (5)
Place the dip switches to put the corresponding function into effect.
(1) Filling in directory
Open the directory pushing the cut edge. Fill in names
(2) Silencing chime tone
On KB-3MRD 8 KB-3HRD;
Chime Tone Mute : To mute the chime tone from any d
move the switch to the Up position. To hear the chime, leave in the lower default position.
(3) White light on/off
On KB-3MRD only;
When ambient light is low (during night, etc.),
the white light on door station will turn on automatically
when door calls or during monitoring.
Adjustments
e in standby
[MID] — [HIGH] — [Low]
|
2 TONE button Chime
volume control
2 TONE button Handset
receive volume control
STANDARD| — |HIGH| — [VERY HIGH |
| |
1 LIVING 2 KITCHEN
with pen. CC) CJ)
° == 6 KID 7 BEDROOM
oor station,
2: for door 2
3: for door 3
Chime (1: for door 1
ton
Chime volume
In standby mode, press TONE button. Chime tone sounds
at mid level, and changes when the button is pressed.
MID (initially set) - HIGH - LOW - MID...
When power switch is turned off or after power failure,chime volume will
return to MID position.
Receive volume
While communicating with door or another room station, press TONE
button. Pressing button repeatedly, the recieve volume changes:
STANDARD (initially set) — HIGH — VERY HIGH —- STANDARD ...
Notes:
1. When acoustic feedback takes place in answering door, with receive
volume set to HIGH or EXTRA HIGH position, put the volume back
to STANDARD position.
2. Once receive volume is set, it will be in memory after communication.
(When power switch is turned off or after power failed, receive volume
will return to STANDARD position)
-5-
Auxiliary light power control
4 WIRING DIAGRAM
“EON DAR KB-DAR KB-DAR
(0
r IF-DA)
Master
KB-3MRD
Sub
KB-3HRD
Sub
KB-3HRD
Sub
KB-3HRD
Sub
KB-3HRD
—
oan AJ 1A1
N Hi
—
—
o. al 2A]
—
on ay aM]
| 7” a
— NP . =
un 025
| „x ET] STATION
—
Master
Sub
KB-3HRD
Sub
KB-3HRD
Sub
KB-3HRD
{D
[= [= [= [MN | (Terminated)
[mA [mA [ MA [HA
[mB [ MB mB № Ig
[mC Mc [EC № с
STATION #2 STATION #3 STATION #4 STATION #5
— J J —,
y
See 5. MOUNTING Item 5 on Page 7.
Connectors for optional devices (supplied with KB-3MRD)
Selective door release
control
Door 1
EL-12S
V7
ACT .
C Trans. |
RY-3DL
и
Li
11
Hu b1
— | b2
|. |63
L2] | L|
C2 D1
L2| |E
| 02|
1-3 |
C3
L3 |
CN12
BROWN
RED
ORANGE
—
+
—
Yellow (M2)
Orange (M1)
| Door release control.
NOTE:
* Time lapse control signal is provided
Black by photo-coupler as long as the image
À Cut off and White } Unused is on the monitor KB-3MRD (CN12 :
insulate Y Gray | orange-yellow : rated 24V DC, 10mA)
= Purple (b3) | Auxiliary light power control [CN12]
Blue (b2) | input. (for doors 1~ 3)
= Green (b1) CT Orange TPUT
— Yellow ime lapse video control output KB-3MRD | Y Yellow UTP
Orange
Red
(У— |
Brown (V+)
(See Note).
Video output 1Vp-p/75Q.
Connect TV monitor.
/\ Cut off and insulate all the unused wires.
YELLOW
GREEN
BLUE
PURPLE
GRAY
WHITE
BLACK
CN11
ORANGE
— YELLOW +
N J
A Door release and auxiliary light controls are alternatively used.
* Auxiliary light: When door calls, each light turns on and stays lit until
the room station hangs up handset.
Run audio/video wires in a pair cable. As to power
supply, extend 2 wire cable separately from power
e Cable:
/N Do not use an
supply to each monitor location.
y vacant terminal for any other purpose.
5 MOUNTING
KB-3MRD, KB-3HRD
1 Loosen two screws on bottom.
— — — — >
Uk (attached)
S Pull the front case up
screw q and unhook at top.
(attached) N
3 Attach the back case to 2-gang box or on wall.
Power supply
24V +, —
terminals
2-gang box
Audio / video wires
2 Pull up front case slightly, and off the chassis.
Back case
N
\ J T
Power supply 1
Screw (4)
Audio / video
wires
Cut off the cable inlet on bottom of back case.
1}
—
Cable inlet (2)
E @ | Bottom view
dé | J (back case)
5 Assign station # and set impedance with DIP
switches.
Impedance
[MN] onlast KB-3HRD station
Ш | >
(A) [ mM when connecting further
№ | KB-3HRD station
O
ON <—
Station #
1 2 3 4 5
№ |- № |- Ш |- Wm J+ Ш J+
OI» Oo [Je We B® mo
Gs Ga O me GM a GM Je
O_M- O_M- O 1- O_M- OM -
A
t Initial setting on KB-3HRD
Initial setting on KB-3MRD
Unit holding pin
AT
v Y Y Y
Make sure all connectors are properly
seated between front and bac
of the unit before closing.
sections
4 Conect wires from each door station,
room station, etc.
SET switch
018) 1 section
O
Li
| []
Tre 5
535253535000
Ss
Terminal bank
$0.65mm ~ ¢1.6mm
22AWG ~ 12AWG
9mm
—
ое р |В1 |
10 } | В2
05 ) |1A1
0 p |1A
A Lu à
СТЛ
LL E L
RELEASÉ button
Strip wire by 9mm (3/8"), and insert the wire into
slot. To unlock, press on the release button.
=p |3A1
=p |3A2
1 = =A pe
a
<
q
lal
L
6 Aligning on the hook, put together front case and back case.
Screw
< (attached)
Hook on top, and slightly
pull down front case.
Screw
(attached)
Notes:
» Securely plug all the connectors into each slot.
» Be careful that connecting wires are not
pinched between the components.
7 Tighten two screws at bottom.
- 7 -
6 TECHNICAL PRECAUTIONS
OPERATING TEMPERATURE
KB-DAR: - 10°C ~60°C (14°~ 140°F).
KB-3MRD: 0°C ~ 40°C (32°F ~ 104° F).
LCD MONITOR
* |t must be noted in advance that the TFT color
LCD panel, though manufactured with very
high precision techniques, inevitably has a
very small portion of picture elements that are
steadily lit or not lit at all, which is not considered
a unit malfunction. The LCD monitor looks dark
in the bright sunlit area, etc. Adjust BRIGHT
control to high position to increase monitor luminosity,
or reduce ambient lighting.
* When holding handset close to video monitor, the
image may vary, but this is not a malfunction.
e KB-3MRD unit surface becomes warmer while
being powered, but this is not a malfuction.
e Strong light, such as direct sunlight, etc. may cause
silhouette on the monitor, but this is not a malfunction.
e When outside temperature lowers sharply after
rainfall, etc., the inside of camera may fog up slightly,
causing a blurry picture, but this is not a malfunction.
Normal operation will be restored when moisture
evaporates.
* KB-3MRD may collect dust on the top of the unit.
Clean unit as needed.
* Do not apply any caulking sealant around video
door station. The openings at the bottom will help
rain to dissipate.
CLEANING
Clean KB-3MRD and KB-DAR with a soft cloth
dampened with neutral household cleanser. Never
use any harsh cleaner or cloth. Do not spray high-
pressure water on KB-DAR.
7 SPECIFICATIONS (KB-3MRD)
* Power source:
* Consumption:
e Call-in:
e Communication:
e Wiring:
e Wiring distance:
24V DC.
Max. Standby
KB-3MRD: 710mA 230MA
KB-3HRD: 260mA 80mA
KB-3SD: 85MA 50MA
4-, 2- & 8-tone chime from door 1, 2
a 3, with adjustable volume.
Pre-tone and voice for internal call,
with adjustable volume.
Simultaneous with handset.
Handsfree simultaneous at room
station internally called.
2 solid parallel wires, non-polarized
to door.
2 solid parallel wires, non-polarized
to room,
plus 2 wires to power supply
(separately jacketed).
0.65mms 1.0mme
e KB-3MRD to door 100m 200m
e KB-3MRD to farthest monitor/KB-3SD 50m 100m
e KB-3MRD to door IF-DA 150m 360m
22AWG 18AWG
e KB-3MRD to door 330' 660!
e KB-3MRD to farthest monitor/KB-3SD 165' 330'
e KB-3MRD to door IF-DA 450! 1,000’
A For use of cables not specified, normal operation
or max. communication distance cannot be
guaranteed.
Cable Specify for wiring to both door and inside stations.
1. 0.65mmg to 1.2mmg (22AWG to 16 AWG).
2. PE (polyethylene) insulation & Vinyl-sheathed
cable.
Attenuation of less than — 6.5dB at 10MHz./100m,
330' length.
3. Solid core conductor.
4. Line impedance : = 75Q (less than 100Q at the
highest).
For other types, normal operation or max.
communication distance cannot be guaranteed.
* Housing á color: Fire-retardant ABS plastic, in white.
185 (W) x 195 (H) x 84 (D) (mm).
7-1/4"(W) x 7-3/4"(H) x 3-5/16"(D).
* Dimensions:
e Weight:
900g (1.98 Ibs.) approx.
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A.S., LISSES-EVRY, FRANCE
< AIPHONE*
Providing Peace of Mind
http://www.aiphone.net/
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement