Aiphone TA-12F User's Manual

Aiphone TA-12F User's Manual
AIPHONE COMMUNICA
TELEPHONE TYPE INTERCOM TA-F <A SERIES
MODELS TA-1F ryreA (single-way) TA-3F ТУРЕ А three-way)
TA-6F ТУРЕА (six-way) TA-12F type A (twelve-way)
COMMON TALK SELECTIVE RING
— INSTRUCTIONS -
NAMES AND FUNCTIONS
(1) Case Handset
(2) Station selector buttons Receiver
3) Paging button Microphone
(4) Coil cord
(5) Terminal cord
(6) Terminal box
Directory card
OO
Receiver cradle for wall mounting , included
SPECIFICATIONS
* Power source: DC 12 volt. Use PS—12S (PS—12C in North America) AC adaptor.
* Current consumption: 65 mA maximum at calling; 25 mA at talking.
* Calling: Push-button station selection. An electronic tone sounds when the selected station
button is depressed.
* Paging: Use PG-U 1vee A paging adaptor in conjunction with standard paging amplifier and
speakers
* Wiring: Up to 18 conductors may be required. Please refer to wiring diagram showing system
that meets your requirements.
FEATURES
* Up to 13 selective ring stations can be connected in a system.
* Single channel common talk system. Conference calls can selectively include up to 13 stations.
* Phone designed for either desk use or wall mounting.
* Door station TC—D tyre A can be installed with adaptor DF—U TyPE À to master stations TA—3F Tyre À , TA—GF
TyPEA, or TA-12F TyPEÂ. (Up to two door stations may be connected to up to 5 masters.)
* Phone system may be connected to existing paging and background music system using adaptor PG—U
TYPE A
* Talkback paging available through existing paging system using adaptor PA-B.
INSTALLATION
Do not attempt to install your intercom system until you have read and thoroughly understood the installation
procedure. Aiphone’s warranty is void if system is installed in a manner other than described in this manual.
Lay out your system in advance. Determine the exact location of each station. We recommend a full comple
ment of wire be installed, even though you may not initially be installing the maximum number of stations available
to your system. This way, should you decide to add a station later, you can avoid running additional cables to
existing stations. Do not connect wires to terminals D1 or D2 unless appropriate equipment is used. Phone system
will not operate if these wires are connected in parallel through system.
WIRING REQUIRED
TA-1F - 5 Conductors maximum TA—6F = 12 Conductors maximum
TA-3F - 9 Conductors maximum TA—12F - 18 Conductors maximum
Refer to the chart below and select the proper wire gauge to meet your requirements.
AWG WIRE SIZE 24 AWG 22 AWG 20 AWG 18 AWG
DISTANCE 1300" 2100" 3300" 5300"
DIAMETER OF WIRE 0.5 mm 0.65 mm 0.8 mm 1.0 mm
DISTANCE 400 m 650 m 1000 m 1450 m
Begin your installation with station #1. A space is provided at the left of the diagram to write in your color
code. Note the position of the C terminal at each station. Be sure you wire each station correctly.
After installing your second station we recommend that the power supply be connected to the +and - terminal
lines at a convenient location and that a test be made for calling and talking between each station. As each addi-
tional station is.installed re-test between each station. Unplug power supply while making wiring connections.
ACTUAL TA-F TERMINAL LOCATIONS
TA-1F ee A ТА-ЗЕтуРЕ А ТА-бЕт/РЕ А TA-12F TyPEA . .
(1) - (à : for connecting relative stations
10 pO в © Р© 0d PO| ® - O: for power supply
e 02 2 во | 02 2 52112029 © : for receiving call and talking
С 2 o 4 DI 4 10-01 — 62 : for connecting door station
3 с 30 cc 30 9 O CO
_Q 20 [email protected] 20 —O 20 #9 _0 © : for paging
+0 10 +0 10 +40 , 0 70,0
=
INSTALLATION FOR WALL MOUNTING
1) Attach the mounting bracket to wall or “< |
single gang plaster ring.
2) Attach handset cradle included. as shown in
illustration.
бов
1-83. 59
by d
D
‘
Or
EQUIPMENT AVAILABLE FOR USE WITH YOUR TA-F tree A PHONE SYSTEM
TA—12F TYrEA: 12 call master station
with paging button and door station
capability.
TA—1F TyPE À : 1 call master station with
paging button,
TC- D Type A: Surface or semi-flush mount
door station with push button for calling
connected master.
TA—3F TyPE À : 3 call master station with
paging button and door station capability.
TA—6F TYPE À : 6 call master station with
paging button and door station capability.
DF—U tyre A: Adaptor for door station.
Required between door station TC--D TyPE À
and TA—F type A stations.
SP—3: Paging speaker. Complete and | — PG-U TYPE A: Paging adaptor for
ready to install including round flush = connecting any amplifier and background
mounting frame. Transformer installed music source to your TA—F system.
tor 70V line operation. Features paging volume, treble & bass
(Not available in North America) controlsand automatic background music
Tu“ Sat,
PS-12S: Power supply for system.
Standard everywhere except in North
America.
N—S: Square frame for SP—3 speaker.
N-E: Round surface frame for SP—3
speaker.
EL—9S: Electric door release. Requires
separate transformer and RY— AC.
PS-12C: CSA & UL LISTED power sup- PA—B: Talkback paging adaptor.
ply (available only in North America).
NCH-1:Noise cancelling handset espe-
cially designed to allow Aiphone TA-F
phone system to operate in extremely
noisy areas. Field installed only.
RY—AC TYPEA; Relay for operating
external device such as additional calling
buzzer or bell, door release, etc.
TA—6F TYPE A: WITH TWO DOOR STATIONS CONNECTED.
TC-D TYPEA STATION STATION STATION STATION
1 2 3 4
TA-6F DEF-UTYreA TC-DTYPEA
TYPE A
nge (3
Black (4)
range (3
Black (4)
PS-12S
or
PS-12C
NOTE: 1. Example above shows 4TA—6F TYPEA phones. 1 additional phonemay be added if required.
2. Maximum of 2 door stations may be connected to up to 5 phones per system.
3. Do not use terminal 41 on each phone for communication with door station.
OPERATION: When call tone is heard at master, lift handset and press button No.4 (or No.5)
once and begin conversation.
TA-12F r= A ALL MASTE
STATION STATION И STATION STATION YI STATION STATION JI STATION
1 2 3 4 5 6 7
mImI mOOO CON 02-2-3 M4=-X=
TA-12F rveA PHONE SYSTEM with PAGINC
STATION ‚A STATION ‚1 STATION STATION “À STATION STATION 7 STATION
1 2 3 4 5 6 7
W
R
|
T
E
W
!
R
|
N
G
C
O
L
O
U
R
C
O
D
E
H
E
R
E
R PHONE SYSTEM
STATION A STATION À STATION STATION A STATION STATION
8 9 10 11 12 13
and BACKGROUND MUSIC SYSTEM
STATION
11
STATION
10
STATION
12
STATION
13
STATION
8
STATION
9
PAGING
SPEAKER
EXISTING
PAGING AMP
OUTPUT
O_O
1
BACKGROUND
MUSIC SOURCE
TA—6F type A SYSTEM WITH DOOR STATION & ELECTRIC DOOR RELEASE
TC-D TYPE A STATION STATION STATION STATION Example shows 4 TA-GF Type A
1 2 3 A ЩИ ‚
phones. One additional phone
may be added if required. Button
TA-6F Sallows conversation with door
TYPE A
station. Button 6 operates door
release.
2
range (3)3
4
Black {4} IN
EL—9S
YELLOW
BELL
TRANSFORMER
FOR DOOR
LOCK
WIRING DOOR RELEASE EL-9S
AVAILABLE CYLINDRICAL LOCKS
EL—9S The bolt width
should be within
1 3/32”.
WHITE
RED Y -AC |
BLACK |TYPE A| YELLOW
EL- 9s
Trans.
Separate bell transformer (not supplied by
Aiphone) required to power door lock.
YELLOW
FT
CYLINDRICAL
LOCK
=
WITHIN
134”
TA—F TrrEA INTERCOM SYSTEM WITH TALKBACK PAGING
EQUIPMENT REQUIREMENTS
1) TA—F system shall consist of TA—3F, TA—6F or TA—12F phones. TA—1F will not operate with
talkback paging adaptor PA—B.
2) One PS—12C, one PG—U TYPE A, one PA—B, one paging amplifier with 70 volt line and output of less
than 50 watt RMS, and appropriate paging speakers as required must be used.
3) Door station adaptor DF—U tyrEA and TC—D TyrEA door station can not be included in system when
installing talkback paging adaptor PA—B.
For the full information, please refer to PA-B instruction sheet.
STATION
6
STATION
7
STATION
4
STATION
5
STATION
3
STATION
1
STATION
2
TALKBACK
PAGING
SPEAKER
|
70V LINE
NON
ITY
NON PORALITY
TO PAGING AMP
or ADAPTER
OO) | BACKGROUND
MUSIC
— SOURCE
TO PHONES
PS—12S or PS—12C
POWER SUPPLY DC 12V
|+REV-OUSUNO
MASTER/SUB SYSTEM
Any combination of TA—F series phones can be intermixed to develop a master-sub system to meet your
requirements. The example below shows 6 TA—1F stations connected to 1 TA—6F.
MASTER
TA—6F
, 7
2 CT
19
4
5
e
с?
PS—12C ’
PS 125 "о
Power Supply D2
TD e e e O e, e
% e "D e "D
C7 \ nn \ J _
All stations have paging ability. Refer to paging diagram for proper connection to paging system.
FIELD INSTALLATION OF NOISE CANCELLING HANDSET MODEL NCH-1
For extremely noisy areas, Aiphone has developed a special handset which allows excellent communication
from a phone in a noisy area to other phones in the communication system. Designed to work
with Aiphone Model TA-F, this handset contains an amplifier for communication and noise cancelling
mouthpiece.
TO INSTALL
(a) Remove two screws on bottom of phone as shown, using a Phillips screw driver. (fig. 1)
(b) Carefully lift the plastic case from the base.
)
(c) Lift hook anchoring coil cord to metal base. (fig. 2)
(d) Carefully remove red, white and black wires from printed circuit board using soldering iron.
Remove old handset, and retain for spare parts.
(e) Attach red, white and black wires from noise cancelling handset coil cord with soldering iron as shown.
Be sure your wires are in the correct order. (fig. 3)
(fy Веп4 hook back, (Note (c)), replace plastic case (Note (b)), and screws (Note (a)).
Dram
INSTALLING EXTERNAL SIGNALING DEVICE RELAY
Example shows station 4 with relay RY-AC which switches an external light, bell, horn or buzzer (external
signal devices not provided by Aiphone).
EXTERNAL SIGNALING DEVICE
NOT TO EXCEED 2A 250V
| STATION
| STATION | STATION
: 3 : —»
TO EXTERNAL
POWER
6 SOURCE. >
+. YELLOW
>
> ; TO RY-AG
> TYPE
co 2 D wl ЭГ x
>. > Hi wi U
3 з © с“ 70 = = 3
1D 70 30 co -
PS—12C p © , O © ©
or
PS—12S 01D p1 © о @ 01 ©
Power Supply оо @ D7 @ 02 © 00 @
0 2 що ‚ ©
_ D 6 ©
OPERATION _ 7
* Calling: |
Pick up the handset and momentarily depress the selector button of desired station.
* Receiving:
An incoming call is announced by an electronic tone. Pick up the handset and begin speaking.
PAGING OPERATION
* Pick up the handset and make announcement by pushing and holding the paging button. Background music will
automatically’ cut out during paging operation.
CLEANING YOUR INTERCOM STATIONS
* Your Aiphone intercom stations may be cleaned with a soft cloth dampened with household cleanser, such as Mr.
Clean or Fantastik.
x + +
We at AIPHONE are proud of our products. Our designers and engineers strive to bring you the finest in
communication equipment. Each item has been carefully tested and inspected before leaving our factory. Properly
installed and used, your Aiphone intercom system should give years of trouble-free service.
We are pleased to offer the following warranty:
WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal
use and service for a period of one year after delivery to the ultimate user and will repair free of
charge or replace at no charge, should it become defective upon which examination shall disclose
to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final
decision whether there is a defect in materials and/or workmanship; and whether or not the prod-
uct is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect,
accident, or to use in violation of instructions furnished, nor extended to units which have been
repaired or altered outside of the factory.
This warranty does not cover batteries or damage caused by batteries used in connection with the
product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place des-
ignated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving on
site service calls.
re . : Em
FET ЕЕ ЕЕ)
ar]
CLR D
Aiphone Co., Ltd., Nagoya, Japan
Aiphone U.S.A., Inc., Bellevue, Washington ALL OVER THE WORLD AIPHONE
TA—FI—02786) Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement