Instruction of 2CH Relay Receiver Magic 2CH

Instruction of 2CH Relay Receiver Magic 2CH
RFRemotech Radio Frequency Remote Technology
Remote Control Products, Remote Controllable Service, E-MadeinCHN
Email: [email protected]
Http://www.RFRemotech.com
Instruction of 2CH Relay Receiver
Magic 2CH / Magic 2CH C
Mode No.:
RR2LN (Magic 2CH, Superregenerative)
RR2LNC (Magic 2CH C, Superheterodyne)
ASK type, 2 channels. With learning code,
can receive both FIXED code signal and
LEARNING code signal, each channel can
work at MOMENTARY and TOGGLE or LATCH
mode. Can distinguishes the signals from
different channels of the same transmitter,
flexible and a transmitter can work with
multiple discrete receivers. Suitable for most kind of application. There is reverse
Page 1 of 3
RFRemotech Radio Frequency Remote Technology
Remote Control Products, Remote Controllable Service, E-MadeinCHN
Email: [email protected]
Http://www.RFRemotech.com
protection. Among Magic 2CH C is FCC compliant and can be CE certified, with
excellent anti-jam performance and works steadily.
Specs:
Operating Voltage: 12VDC
Stand by Current: 20mA
Operating Current: 45mA (1CH), 80mA (2CH)
Frequency:
315MHz or 433MHz
Decode:
Learning Code, works with FIXED code transmitter and
LEARNING code transmitter
Output Mode:
Momentary, Toggle or Latch(Selectable through Jumper)
Relay:
12VDC,10A 120VAC, 7A 240VDC/10A 28VDC, 7A 240VAC
Dimensions:
54mm x 39mm x 20mm
How Channel 1 Learns Codes:
A. Learn FIXED CODE transmitter:
Turn off supply power, plug JUMPER 1.
Press and release LEARNING BUTTON 1, LEARNING INDICATOR LED is on. Press button
of transmitter within 5 seconds, LEARNING INDICATOR LED blinks once and then off,
then the button is defined to work with the receiver channel 1 in MOMENTARY mode
or LATCH ON mode.
Depress LEARNING BUTTON 1 and don’t release until LEARNING INDICATOR LED turns
on (it costs 5 seconds), then press button of transmitter within 5 seconds, LEARNING
INDICATOR LED blinks once and then off, then the button is defined to work with the
receiver channel 1 in TOGGLE mode or LATCH OFF mode.
A receiver channel can save codes of 10 different buttons/channels of transmitter. When
a button/channel of transmitter is learned twice, the former code is cleared and the later
one is stored automatically. The codes remains in the receiver channel even though
supply power is disconnected.
B. Learn LEARNING CODE transmitter:
Turn off supply power, unplug JUMPER1. Then the same steps as the ones of “A.Learn
FIXED CODE transmitter” above.
How Channel 2 Learns Codes: the same as Channel 1.
How to Clear Codes:
Keeping depressing LEARNING BUTTON for 10 seconds or more, LEARNING INDICATOR
LED will blinks twice, all codes are cleared.
How transmitter and receiver work:
Page 2 of 3
RFRemotech Radio Frequency Remote Technology
Remote Control Products, Remote Controllable Service, E-MadeinCHN
Email: [email protected]
Http://www.RFRemotech.com
Only when learning succeeds, receiver can work availably.
MOMENTARY mode: Plug JUMPER 2 of receiver on top, if button is defined to work in
“MOMENTARY mode or LATCH ON mode”, the receiver channel will work in
MOMENTARY mode with the button/channel.
TOGGLE mode: Plug JUMPER 2 of receiver on top, if button is defined to work in
“TOGGLE mode or LATCH OFF mode”, the receiver channel will work in TOGGLE mode
with the button/channel.
LATCH mode: Plug JUMPER 2 of receiver at bottom, if button is defined to work in
“MOMENTARY mode or LATCH ON mode”, the receiver channel will work in LATCH ON
mode with the button/channel of transmitter; if button is defined to work in “TOGGLE
mode or LATCH OFF mode”, the receiver channel will work in LATCH OFF mode with the
button/channel of the transmitter.
Page 3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement