Aiwa XR-MN5 User's Manual
4-246-022-21
030227AMI-H-FM
Micro Hi-Fi Component System
XR-MN5
WARNING
The following caution label is located inside the apparatus.
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAN.
ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLING.
To prevent fire, do not cover the ventilation of the apparatus
with newspapers, table-cloths, curtains, etc. And don't place
lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
VORSICHT: UNSICHTBARE LASERSTRAHLUNG. WENN ABDECKUNG GEÖFFNET
UND SICHEREITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL
AUSSETZENSTRÅLING.
VARO!: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-TIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KÄTSO SÄTEESEEN.
VARNING: OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
En
ADVERSEL: USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
VIGYÁZAT!: A BURKOLAT NYITÁSAKOR LÁTHATATLAN LÉZERSU-GÁRVESZÉLY!
KERÜLJE A BESUGÁRZÁST!
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
2
This appliance is classified
as a CLASS 1 LASER
product.
This label is located on the
rear exterior.
Don't throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
PRECAUTIONS
On operating voltage
Before operating the system, check that the operating voltage
of your system is identical with the voltage of your local power
supply.
On safety
•The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
•Unplug the system from the wall outlet (mains) if it is not to
be used for an extended period of time. To disconnect the
cord (mains lead), pull it out by the plug. Never pull the
cord itself.
•Should any solid object or liquid fall into the component,
unplug the stereo system and have the component checked
by qualified personnel before operating it any further.
•The AC power cord must be changed only at a qualified
service shop.
On placement
•The unit should be situated with adequate space around it
so that proper heat ventilation is assured. Allow 10 cm
clearance from the rear and the top of the unit, and 5 cm
from each side.
•Do not place the unit in an inclined position.
•Do not place the unit in locations where it is;
- Extremely hot or cold
- Dusty or dirty
- Very humid
- Vibrating
- Subject to direct sunlight.
TABLE OF CONTENTS
On heat buildup
•Although the unit heats up during operation, this is not
malfunction.
•Place the unit in a location with adequate ventilation to
prevent heat build-up in the unit.
If you continuously use this unit at a large volume, the cabinet
temperature of the top, side and bottom rises considerable.
To avoid burning yourself, do no touch the cabinet.
On operation
•If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture may
condense on the lens inside the CD player. Should this occur,
the system will not operate properly. Remove the CD and
leave the system turned on for about an hour until the
moisture evaporates.
•When you move the system, take out any discs.
Notes on discs
•Playable discs on this unit are Audio CDs (CDs), CD-R/
CD-RW with audio data (CD-R/RW) and CD-R/CD-RW with
MP3 files (MP3-CDs).
•Discs recorded on CD-R/RW drives may not be played back
because of scratches, dirt., recording condition or the drive's
characteristics.
•CD-R/RW discs which are not finalized at the end of
recording cannot be played back.
•Do not attach adhesive label, etc. to either side of a CD-R/
RW disc, as doing so may cause malfunction.
•Do not load an unrecorded CD-R/RW disc. The disc may be
damaged.
•Do not insert 8-cm (3-inch) discs. Those discs cannot be
played on this unit. Moreover, if you insert the discs of that
size forcibly, you may not be able to eject it.
•Discs with non-standard shapes (e.g., heart, square, star)
cannot be played on this unit. Attempting to do so may
damage the unit. Do not use such discs.
•DVD, SACD, CD-ROM and VCD cannot be played on this
unit.
PRECAUTIONS .................................... 2
PREPARATIONS ................................... 4
PARTS AND CONTROLS ......................... 5
ADJUSTMENTS BEFORE OPERATION .......... 8
SOUND ADJUSTMENTS .......................... 9
CD OPERATIONS ................................ 10
MP3-CD OPERATIONS ......................... 12
TUNER OPERATIONS ........................... 14
TAPE PLAYBACK ................................ 17
TAPE RECORDING .............................. 18
TIMER OPERATIONS ........................... 21
REFERENCE ..................................... 23
Music discs encoded with copyright protection
technologies
This product is designed to playback discs that conform to
the Compact Disc (CD) standard. Recently, various music
discs encoded with copyright protection technologies are
marketed by some record companies. Please be aware that
among those discs, there are some that do not conform to the
CD standard and may not be playable by this product.
If you have any questions or problems concerning your stereo
system, please consult your nearest Aiwa dealer.
3
En
PREPARATIONS
Connection
Plug in the AC power cord to the AC power socket after all
other connections are made.
1 Connect the speaker cords to the speakers.
3 Connect the supplied antennas.
Connect the FM antenna to the FM 75 Ω terminal and the
AM antenna to the AM LOOP jack.
AM antenna
Remote commander
Detach the battery compartment lid at the rear of the remote
commander and insert two R6 (size AA) batteries with correct
polarity.
Connect the copper cords to the + terminals and the silver
cords to the - terminals.
En
R6(AA)
2 Connect the speakers to the main unit.
Connect the right speaker to the SPEAKERS R terminals
and the left to the SPEAKERS L terminals. The copper
cords go to the 0 terminals.
FM antenna
4 Connect the AC power cord to an AC power
socket.
When the AC power cord is connected to a wall outlet for
the first time, DEMO appears in the display.
To deactivate the DEMO, press ECO/RDS or i-Bass/DEMO.
Speakers
•Do not short-circuit the 0 and 9 speaker cord leads.
•Do not leave objects generating magnetism or objects
affected by magnetism near the speakers.
Antennas
Keep antennas away from metallic objects, electrical
equipment and cords.
•FM antenna: Extend fully and position for the best
reception. If reception is poor, connect an optional outdoor
antenna to the FM 75 Ω terminal. Note that, when connecting
an optional outdoor antenna, use an adaptor as required.
•AM antenna: Rotate to find best reception.
4
•Replace the batteries with new ones when the operational
distance between the remote commander and main unit
becomes shorter.
•Remove the batteries if the unit is not going to be used for
an extended period of time.
•The remote commander may not operate if it is used under
intense sunlight or if its line of sight is obstructed.
PARTS AND CONTROLS
Main unit: front
Refer to the pages indicated in parentheses for details.
1
4
5
8 i-Bass/DEMO (4, 9)
Produces rich and clear low frequency sound.
Switches DEMO on and off while the unit is turned off.
6
SYNCHRO REC (18)
Starts recording and CD play simultaneously.
9 PUSH EJECTz (17-19)
Opens or closes the cassette holder.
7
REC START/REC PAUSE (18-20)
Starts and pauses recording.
0 PHONES jack
Plug in optional headphones set with a stereo mini plug
(ø3.5 mm). Speaker output is cancelled.
2
3
3 ECO/RDS (8, 14-16)
Sets the ECO mode on or off.
Tuner: Activates RDS features.
8
9
0
1 POWER 6STANDBY/ON (8)
Switches the unit on and off (standby).
2 ECD (8, 10-12)
Starts and pauses CD play.
TUNER/BAND (8, 14)
Selects tuner function and the tuner band.
dTAPE (REC MUTING) (8, 17, 19)
Starts playback and changes the playback side.
Also used to enter 4-second blank spaces during
recording.
AUX (8)
Selects the function of external equipment connected to
AUX IN jacks.
4 s (10-12, 17, 18, 20)
CD and Tape: stops playback.
Tuner: clears a preset station.
TUNING f/r-, +t/g (8,10-12,
14, 17, 21, 22)
CD: skips to a previous or a succeeding track when
pressed, searches a track in fast forward or reverse
playback when held down.
Tape: rewinds or fast forwards the tape.
Tuner: manually tunes up or down within the band.
5 VOLUME (9)
Adjusts the volume.
6 TREBLE (9)
Adjusts the treble level.
BASS (9)
Adjusts the bass level.
7 zCD EJECT (10, 12)
Ejects the disc(s).
CD slot buttons (1-5) (8, 10-12)
Selects a disc slot.
Starts CD play for one desired disc.
5
En
Main unit: rear
Refer to the pages indicated in parentheses for details.
1
2
3
4
5
En
6
1 AM LOOP jack and FM 75 Ω terminal (4)
Plug in the supplied AM and FM antennas.
2 SUB WOOFER3 jack
Connect optional powered sub woofer with a built-in
amplifier to the jack.
3 DIGITAL OUT (OPTICAL) jack
CD digital sound signals can be output through this jack.
Use an optical cable to connect digital audio equipment.
Fit an optical cable plug in the DIGITAL OUT (OPTICAL)
jack and push it to connect.
4 AUX IN jacks
Accept analogue sound signals from external equipment.
Connect external equipment using an optional connecting
cable with RCA phono plugs (red plug to R jack, white
plug to L jack). Refer also to the operating instructions
for your equipment.
To switch function to external input, press AUX.
To change a source name in the display of the
AUX function.
Hold down AUX and press POWER while the power is
on.
AUX
VIDEO
TV
5 SPEAKERS3 terminals (4)
Connect the speaker cords of the supplied speakers.
6 AC power cord (4)
6
Remote commander
Refer to the pages indicated in parentheses for details.
1
8
REV MODE (17, 18, 22)
Selects a reverse mode.
DISC/ALBUM (12)
Selects disc mode or album mode on an MP3-CD.
2
9
3
4
5
6
7
TUNER MODE (15)
Switches between stereo or monaural FM reception.
0
!
@
#
Buttons with the same or similar names on the main unit
basically have the same function.
1 POWER (8)
2 1–10/0, >10 (10-12, 15, 19, 20)
CD: selects a track of the specified number.
Tuner: tunes in the station with the specified preset
number.
CD EDIT/CHECK (19, 20)
Selects edited CD recording.
3 SHUFFLE/PROGRAM (11)
Selects shuffle or programmed CD playback mode.
REPEAT (11)
Selects repeat CD playback mode.
4 ALBUM/PRESETN,M (12, 15)
MP3-CD:Skips to a previous or succeeding album.
Tuner: Tunes in a preset station.
f/r,t/g (8, 10-12, 14, 17, 21,
22)
ENTER (8, 14, 15, 21, 22)
Determines the mode.
Stores the received station to preset.
TUNER/BAND (8, 14)
CLOCK (8)
Selects clock mode.
AUX (8)
MUTING (9)
To turn off the sound temporarily.
7 SHIFT
Hold down when pressing a numbered button to change
its function to that printed above the number.
8 DISC SELECT (10, 12)
Selects a desired CD slot.
9 CLEAR (11, 15, 21, 22)
CD: Clears a CD program
Tuner: Clears a preset station.
En
0 i-Bass (9)
TONE (9)
Selects the bass or treble adjusting mode.
! s (10-12, 17, 18, 20)
@ FUNCTION (18-20)
Switches the active function among TAPE, TUNER, AUX
(VIDEO or TV) and CD.
# VOLUME +,- (9)
5 ECD (8, 10-12)
The numbered buttons take on these functions when pressed with
SHIFT held down:
TIMER (21, 22)
Selects timer mode.
SLEEP (21)
Selects sleep-timer mode.
dTAPE (8, 17)
6 DISPLAY (10, 12)
Changes the display in CD playback mode.
DIMMER (8)
Adjusts the display window brightness.
7
ADJUSTMENTS BEFORE OPERATION
POWER
6STANDBY/ON
ECO/RDS
Setting the clock
ECD,
POWER
TUNER/
BAND,
dTAPE, CLOCK
AUX
f,g
En
1 In stop mode, hold down SHIFT and press CLOCK
on the remote.
Go to step 3 when the hour of the clock display flashes.
ENTER
ECD,
TUNER/
BAND,
dTAPE,
AUX
f,g
SHIFT
DIMMER
Power
ECO mode
Turning the unit on
Press POWER 6STANDBY/ON (POWER on the remote ).
Alternatively, press dTAPE, TUNER/BAND, AUX, ECD
or one of the CD slot buttons (1-5). Playback will start
automatically if a disc or tape is loaded.
Reduces power consumption in standby mode with the following
operations.
Turning the unit off
Press POWER 6STANDBY/ON again.
The unit goes into standby.
Dimmer
The display window brightness can be selected.
Press DIMMER on the remote.
Each press of the button changes between darker and brighter.
8
Press ECO/RDS.
Each press of the button changes the mode as follows;
ECO ON: Power economizing mode is activated.
When the unit turns off, everything on the display clears and
only the red indicator above POWER lights to show that the
power is being supplied.
ECO OFF: Power economizing mode is cancelled.
When the unit turns off, the clock display appears.
Initial mode is ECO OFF.
Standby power consumption
ECO ON: 0.26 W
ECO OFF: 15 W
2 Within 6 seconds, press ENTER.
The hour flashes in the display.
3 Press f or g to set the hour, then press
ENTER.
4 Press f or g to set the minute.
Each press changes the time in 1-minute steps.
5 Press ENTER.
The time display stops flashing and the clock starts from
00 seconds.
To display the time while the power is on
Hold down SHIFT and press CLOCK on the remote.
The time will be displayed for 6 seconds.
If "- -:- -" appears when the unit is turned off
There has been a power interruption. Reset the clock.
SOUND ADJUSTMENTS
MUTING
TREBLE,
BASS
VOLUME
i-Bass
f,g
SHIFT
i-Bass
TONE
Volume
Bass and treble
Turn VOLUME (press VOLUME +,- on the remote).
Adjust from 0 (minimum) to 33 and MAX (maximum).
Turn BASS or TREBLE.
When using the remote, press TONE repeatedly to select the
bass or treble, then press f or g within 6 seconds.
Each level can be adjusted from "–5" to "+5".
•If the sound becomes distorted, lower the level.
Muting
Hold down SHIFT and press MUTING on the remote.
Playback continues without sound and "MUTING" appears
in the display.
To cancel the Muting, repeat the above or turn up the volume.
En
VOLUME
+,-
i-Bass
Produces rich and clear low frequency sound besides BASS effect.
Press i-Bass/DEMO (i-Bass on the remote).
Each press of the button changes the following four levels:
"i-Bass OFF", "i-Bass 1", "i-Bass 2" and "i-Bass
MAX".
•During recording, you cannot activate or deactivate i-Bass.
9
CD OPERATIONS
To search (playback in fast forward or fast reverse)
Hold down f or g. Release at the desired point.
ECD
s
f,g
zCD
EJECT 1–10/0, >10
DISC
SELECT
CD slot SHUFFLE/
PROGRAM
buttons
REPEAT
(1-5)
ECD
CLEAR
En
DISPLAY
Notes
•Do not insert 8-cm (3-inch) discs. Those discs cannot be
played on this unit. Moreover, if you insert the disc of that
size forcibly, you may not be able to eject it.
•Discs with non-standard shapes (e.g., heart, square, star)
cannot be played on this unit. Attempting to do so may
damage the unit. Do not use such discs.
•Do not attach adhesive lavel to either side CD-R/RW discs,
as doing so may cause malfunction.
•Do not insert more than one disc into one disc slot.
Playback
This unit plays back finalized CD-R/RW discs as well as audio
CDs.
1 Press CD and load disc(s).
Press the CD slot buttons (1-5) and insert a disc with the
labeled side right.
To insert more discs, press CD slot buttons (1-5) so that
the slot changes, then insert a disc.
After reading the loaded disc, " " lights up at the
corresponding disc number (1-5) in the display.
Do not insert a disc forcibly.
10
f,g
s
2 To play all discs, press E CD.
To play one desired disc, press the desired CD
slot buttons (1-5).
Playback starts from the first track and the elapsed
playback time is displayed.
To insert discs consecutively
You can insert discs consecutively at one time.
1 Hold down zCD EJECT on the main unit for 2 seconds.
When no disc is inserted, "ALL INSERT" will be
displayed.
When the disc(s) already inserted, "ALL EJECT" will be
displayed and the unit will eject the disc(s) consecutively.
2 Insert a disc consecutively when "CD No Disc" is
displayed.
Do not insert a disc forcibly.
To stop playback
Press s.
To pause playback
Press E CD. Press again to resume playback.
To select a track
Press f or g repeatedly.
To select a disc and a track on the remote
To select a disc
Press DISC SELECT, then press the numbered button (1-5)
within 6 seconds.
To select a track
Press the numbered buttons in the following way.
- To select 10th track, press 10/0.
- To select 25th track, press >10, 2 and 5.
- To select 30th track, press >10, 3 and 10/0.
Auto resume playback
When you change the function from CD to another one, or
turn the unit off, CD playback is interrupted.
The next time you set the function to CD, the track you
interrupted playback will automatically start play from its
beginning.
To display the remaining playback time
Press DISPLAY on the remote during playback.
The display changes in the following order.
Track number being played and elapsed playing time.
Remaining time of current track.
Remaining time of current disc*
* During programmed playback, remaining time of program
playback is displayed.
* During program playback for plural discs, the remaining
time is not displayed.
* During shuffle playback for all discs, the remaining time is
not displayed.
To eject the disc
Press the desired CD slot buttons (1-5) to select the disc,
then press z CD EJECT.
Shuffle play
Programmed play
In shuffle play mode the unit plays all the tracks on the disc
inserted in random order.
Plays back up to 30 selected tracks in programmed order.
1 In stop mode, press SHUFFLE/PROGRAM on the
remote repeatedly until the "SHUF" indicator is
displayed.
2 Press E CD to start play.
To cancel shuffle play
In stop mode, press SHUFFLE/PROGRAM on the remote
repeatedly until the "SHUF" indicator disappears.
Repeat play
In repeat play mode the unit repeatedly plays all the tracks or
the current track being played on the discs.
Press REPEAT on the remote repeatedly.
The mode changes as follows:
""": Plays all the tracks repeatedly. (up to 5 times)
To play one desired disc, press the desired CD slot
button (1-5).
To play all the discs, press E CD.
"" 1": Plays one track repeatedly. Select the track with f
or g.
To cancel repeat play
Press REPEAT on the remote repeatedly until """ and
"" 1" disappears.
1 In stop mode, press SHUFFLE/PROGRAM on the
remote repeatedly until the "PGM" indicator is
displayed.
2 Press DISC SELECT on the remote, then press
the numbered buttons (1-5) to select a disc.
Go to the next step when "CD CHANGE" disappears.
3 Press the numbered buttons on the remote to
program a track.
The selected track number lights up on the display.
To select the 10th track, press 10/0.
To select the 20th track, press >10, 2 and 10/0.
To select the 35th track, press >10, 3 and 5.
You can select a track by pressing f or g and
then press ENTER.
4 Repeat step 2 and 3 to program other tracks.
5 Press E CD.
•During programmed playback, you cannot select a disc or a
track with the numbered buttons.
•If the total playback time of the program exceeds 99:59
minutes, or if a track with a track number exceeding 30 is
programmed, the playing time is displayed as "--:--".
•You cannot program more than 30 tracks. "Full" is
displayed.
To clear a previous track
Press CLEAR on the remote. Each time you press the button,
a track is cleared from the end of the program.
To add a track to the program
Repeat steps 2 and 3 before starting playback. The track is
added to the end of the program.
To cancel programed play
Press SHUFFLE/PROGRAM repeatedly until "PGM"
disappears.
•The program content is retained even if the program
cancelled or after programmed playback finishes. The same
program plays back if you carry out step 1 and 5.
When transporting the unit
Please carry out procedures below to prevent the breakage
of CD mechanism.
1 Eject all the CDs and the tapes.
2 Press POWER6STANDBY/ON (POWER on
the remote) to turn the unit off.
3 Disconnect the AC power cord from the wall
outlet.
Notes on CDs
•Do not tilt the unit with a disc inserted.
•Discs recorded on CD-R/RW drives may not be played back
because of scratches, dirt, recording condition or the drive's
characteristics.
•CD-R/RW discs which are not finalized at the end of
recording cannot be played back.
•Do not load an unrecorded CD-R/RW disc. The disc may be
damaged.
To clear the entire program
Press s in stop mode.
11
En
MP3-CD OPERATIONS
ECD
s
f,g
zCD
EJECT 1–10/0, >10
CD slot
buttons
(1-5)
En
ALBUM/
PRESET
N,M
ECD
DISPLAY
Playback
This unit plays back MP3-CDs: discs recorded with MP3 tracks
(files). Basic operations for MP3-CDs are mostly the same as
those in "CD OPERATIONS". Before playing an MP3-CD, also
refer to "Descriptions of MP3" for the details of MP3.
Switching between the disc mode and the album
mode
Hold down SHIFT and press DISC/ALBUM on the remote.
In disc mode, there will be no indication in the display.
In the album mode, "ALBM" lights up in the display.
In the disc mode, all the tracks on the disc can be played.
In the album mode, only the tracks within a selected album
can be played.
1 Press CD and load disc(s).
Press the CD slot buttons (1-5) and insert a disc with the
labeled side right.
To insert more discs, press CD slot buttons (1-5) so that
the slot changes, then insert a disc.
After reading the loaded disc, " " lights up at the
corresponding disc number (1-5) in the display.
Do not insert a disc forcibly.
12
DISC
SELECT
CLEAR
f,g
s
2 To play all discs, press E CD.
To play one desired disc, press the desired CD
slot buttons (1-5).
Playback starts from the first track, and the elapsed
playback time is displayed.
In the album mode, playback starts from the first track of
the first album and it will stop when reaching the end of
the last track of the album.
To stop playback
Press s.
To select an album
Press PRESET/ALBUM N or M on the remote.
To select a track
Press f or g repeatedly.
To select a disc and a track on the remote
To select a disc
Press DISC SELECT, then press the numbered button (1-5)
within 6 seconds.
To select a track
Press the numbered buttons in the following way to select a
track.
(when the album has less than 100 tracks)
- To select the 7th track, press 7.
- To select the 10th track, press 10/0.
- To select the 25th track, press >10, 2 and 5.
(when the album has more than 99 tracks)
- To select the 25th track, press >10, 10/0, 2 and 5.
- To select the 100th track, press >10, 1, 10/0 and 10/0.
- To select the 147th track, press >10, 1, 4 and 7.
Auto resume playback
When you change the function from CD to another one, or
turn the unit off, CD playback is interrupted.
The next time you set the function to CD, the track you
interrupted playback will automatically start play from its
beginning.
To perform Shuffle, Repeat and Programmed
playback for MP3-CDs
The procedures of Shuffle, Repeat and Programmed playback
for MP3-CDs are the same as those in "CD OPERATIONS".
Follow the steps described there.
•In the album mode, only the track within a selected album
can be selected and played.
To display the title of the album and track in the
display
Press DISPLAY on the remote during playback.
The display changes in the following order:
Track number being played and elapsed playing time
Track(file) name and album name* being played
Track title* and artist name* being played
* Album name, track title and artist name are not displayed if
they are not registered.
To eject the disc
Press the desired CD slot buttons (1-5) to select the disc,
then press z CD EJECT.
Descriptions of MP3
An MP3 file stores audio data compressed using MPEG1/2,
the audio layer-3 file-coding scheme.
In this manual, CDs, CD-R discs and CD-RW discs are all
referred to as "discs". We refer to what are called "folder" and
"file" in PC terminology as "album" and "track".
Notes on playing MP3 files
•An MP3 track must be recorded on a disc in the format
compliant with ISO 9660. Note, however, that the unit may
not play tracks in the order they were recorded.
•The maximum allowable number of tracks and albums in a
disc are as follows:
- number of tracks: 255
- number of albums: 255
•The maximum allowable depth of nested albums is 8.
•It may take 30 seconds or more before the unit can start
play of MP3 tracks, depending on the number of recorded
tracks and the complexity of the album tree.
•The unit cannot play MP3 tracks recorded using a packet
writing utility.
•The unit can play MP3 tracks having a file extension ".mp3".
•If you play a non-MP3 track that has the ".mp3" file
extension, you may hear some noise.
Notes on display indications during play
•Up to 8 characters are displayed for the title of an album or
a track. If ID3TAG version 1.X was applied to record
additional information for an MP3 track, up to 10 characters
showing track title is displayed. However, if information of
ID3TAG version 2.X are also recorded in the same MP3
track, the track title of ID3TAG is not displayed. Characters
other than uppercase letters ("A" to "Z") and numerals ("0"
to "9") may not be displayed correctly.
•The elapsed playing time may not be displayed correctly for
MP3 tracks.
Terminology
•ISO 9660
ISO stands for the "International Organization for
Standardization". ISO 9660 determines the file structure for
the CD-ROMs. This unit can play MP3 files recorded in the
format compliant with ISO 9660.
•Nesting of folders (albums)
To organize data files stored in a PC, you can store related
files in a folder. A folder can contain other folders as well as
files. For example, folder A can contain folder B, and folder
B can contain folder C; this is called "nesting of folders".
The maximum depth of nested folders, allowed by ISO 9660,
is 8.
•Writing utilities
There are 3 utilities used to record data on a disc.
1.DAO (Disc At Once) utility
All data to be written must be prepared in advance and
written onto a disc from the beginning to the end in one
operation. No data can be added to a disc on which data
were already written with DAO utility.
2.TAO (Track At Once) utility
Data are written onto a disc track by track. Data can be
added to a disc on which data were written with TAO utility.
3.Packet writing utility
Tracks are divided into smaller pieces while being
recorded, depending on the size of available spaces on
the disc. Data can be added to a disc on which data were
written with packet writing utility.
This unit can play MP3 discs recorded using DAO and
TAO utilities.
•ID3TAG
ID3TAG determines the data format for the text to be added
to an MP3 file, mainly used to indicate a track title or an
artist's name, etc.
Notes on creating MP3 discs
•When converting audio data to MP3
The unit supports MP3 files with a sampling frequency of
16, 22.05, 24, 32, 44.1 or 48 kHz.
To enjoy high sound quality, we recommend storing MP3
files with a sampling frequency of 44.1 kHz and a fixed bit
rate of 128 kbps. The assured bit rate range for sound quality
on the unit is 8 kbps to 320 kbps. If an MP3 files stored
with a bit rate beyond that range is played back, sound quality
is not guaranteed and noise may be generated.
•When creating MP3 discs
Do not store more than 255 albums in a disc. Also, keep the
total number of albums and tracks 255 or less in a disc.
•To play tracks in the order they were recorded
1.Use a writing software capable of recording MP3 tracks
(files) in numerical and alphabetical order. For details on
using the software, refer to the operating instructions
supplied with the software.
2.Use only one album. (Do not create a sub-album within
an album.)
3.Include a two- or three- digit number at the beginning of
each album or track name so that the albums and tracks
are played in order.
<example of recommended names>
01XXXXX.mp3
02XXXXX.mp3
03XXXXX.mp3
04XXXXX.mp3
05XXXXX.mp3
<example of names not recommended>
1XXXXX.mp3
5XXXXX.mp3
10XXXXX.mp3
15XXXXX.mp3
20XXXXX.mp3
(Numbers at the beginning have different digit number.
The tracks will not be played in this order but played in
the order of "1", "10", "15", "20" and "5".)
13
En
TUNER OPERATIONS
Automatic presetting
TUNER/
BAND
ECO/RDS
Scans the receivable frequency range and stores tuned stations
automatically with the preset number.
TUNER
MODE
f,g
TUNER/BAND
En
SHIFT
1–10/0, >10
CLEAR
ALBUM/
PRESET
N,M,
f,g,
ENTER
s
Manual tuning
Preset tuning
1 Press TUNER/BAND repeatedly to select a band.
Preset your favourite stations by either of the following ways
("Manual presetting" or "Automatic presetting") and tune them
in directly by using preset numbers.
The unit switches to the tuner from any other function
and alternates between FM and AM.
2 Press f or g repeatedly to tune in a station.
"TUNE" is displayed when a station is tuned in.
"1" is displayed for FM stereo reception.
To search for a station automatically (Auto search)
Hold down f or g.
The unit searches for a station and stops at reception.
To stop the search manually, press f or g.
•Auto search may not stop at stations with weak signals.
Manual presetting
1 Tune in the desired station.
2 Press ENTER on the remote to store the station.
The preset number, beginning from "1" appears in the
display.
3 Repeat steps 1 and 2 to preset other stations.
The next station will not be stored if a total of 32 preset
stations have already been stored. ("Full" is displayed.)
•If power is interrupted for more than approximately 12 hours,
all settings stored in memory after purchase need to be reset.
14
1 Press TUNER/BAND.
2 Hold down ECO/RDS for 2 seconds until
"AUTO PRESET" scrolls in the display.
3 Press ECO/RDS on the unti or ENTER on the
remote.
If ECO/RDS or ENTER is not pressed within 6 seconds,
automatic presetting is not activated.
The tuning indicator is displayed and scanning begins
with the FM band.
The frequency and the preset number (beginning from 1)
will be displayed when a tuned station is stored.
The display will return to the first stored station when
scanning is finished.
•The unit scans the AM bands if preset numbers are still
available.
•Automatic presetting clears all the previously stored preset
stations.
•If identical RDS stations with alternative frequencies are
detected, only the station with the stronger signal is stored.
Tuning in preset stations
RDS features
Program Type (PTY)
1 Select the band.
RDS (Radio Data System) is a broadcasting service which allows
FM stations to send additional information along with the regular
radio signal.
The additional information is derived from the features of RDS
described below.
This is an identification to specify the program being broadcast
currently.
2 Press ALBUM/PRESET N,M on the remote
repeatedly.
With each press, the station with the succeeding or
preceding preset number is tuned in.
You can tune in the desired preset station directly by
pressing the numbered buttons on the remote.
- To select preset number 7, press 7.
- To select preset number 12, press >10, 1 and 2.
To clear a preset station
1 Tune in the station by preset tuning.
2 Press CLEAR, then press ENTER on the remote within 6
seconds.
Preset station numbers in the band which are higher than
the cleared number decrease by one.
Adjustments
To switch to monaural FM reception
Hold down SHIFT and press TUNER MODE on the remote so
that "TUNER MONO" is displayed.
To cancel, repeat the above so that "AutoSTEREO" is
displayed.
Program Service station name (PS)
The station name is displayed automatically when an RDS station
is tuned in.
Radio Text (RT)
You can show text information such as the title of a song on
the display.
Press ECO/RDS repeatedly when tuning in to an RDS
station.
If the tuned station is not transmitting text information,
"NO RT" will be displayed.
Press ECO/RDS repeatedly to display a program type
when tuning in to an RDS station.
The program type will be displayed for 6 seconds.
If no PTY data or undefined PTY data is being transmitted,
"NO PTY" or "UNDEFINE" will be displayed.
The following PTYs can be received on the unit
*TRAFFIC, NEWS, AFFAIRS, INFO, SPORT, EDUCATE,
DRAMA, CULTURE, SCIENCE, VARIED, POP M, ROCK M,
EASY M (easy listening music), LIGHT M (light classical
music), CLASSICS, OTHER M (other music), WEATHER,
FINANCE, CHILDREN (children’s program), SOCIAL (social
affairs), RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ,
COUNTRY (country music), NATION M (national music),
OLDIES, FOLK M, DOCUMENT, TEST (alarm test), ALARM.
*The unit identifies TRAFFIC with one of the PTYs.
To return to the regular display
Press ECO/RDS again.
Tip:
When FM stereo reception is poor, switching to monaural
reduces noise.
15
En
PTY Search
INFO Search
The unit can search for a station broadcasting your desired PTY
easily. To do so, you need to preset every available station in
advance since the unit searches only the preset stations.
The unit can leap to a station which has just started broadcasting
your desired PTY.
In INFO Search, the unit is in standby mode until the desired
PTY begins. As soon as it begins, the unit "leaps to" another
station with the PTY and returns to the previously tuned station
when it ends. INFO Search makes the function above possible
with the help of INFO which gives the receivers a cross reference
to other stations. You need to preset every available station in
advance since the unit searches only the preset stations.
1 Press ECO/RDS repeatedly until the program type
of the currentry tuned station is displayed.
En
2 Press f or g to select a desired program
type and then press ECO/RDS on the unit or
ENTER on the remote.
The search begins, stops when a suitable station is
detected, and the unit tunes it in.
"NOT FOUND" is displayed if a suitable station is not
found, and the unit returns to the previous station.
If there is no button input for 6 seconds in step 2, the
search is not activated.
Tip:
If TRAFFIC is selected , the unit searches for a station which
regularly broadcasts traffic announcements. Therefore, a
detected station may not be currently broadcasting traffic
announcements. You will, however, be able to hear the
announcements in a while.
1 Tune in an RDS station.
If "INFO" lights up, proceed to the next step.
If not, try to tune in another RDS station until it does.
2 Press ECO/RDS repeatedly so that "INFO PTY"
is displayed.
3 Press f or g to select a desired program
type and then press ECO/RDS on the unti or
ENTER on the remote.
"INFO ON" is displayed for 2 seconds and then the unit
enters the standby mode while "INFO" flashes. When
the unit leaps to another station, "INFO" flashes rapidly.
If there is no button input for 6 seconds in step 3, the
search is not activated.
To stay in the "leaped to" station
Press s on the remote. The standby mode for INFO Search
is also cancelled.
To return to the previously tuned station from the
"leaped to" station
Press ECO/RDS repeatedly so that "INFO PTY" and the
specified PTY are displayed alternately. Then press ENTER
on the remote.
16
To cancel the standby mode for INFO search
Press ECO/RDS repeatedly so that "INFO PTY" and the
specified PTY are displayed alternately. Then press s on the
remote.
•The standby mode for INFO Search will not be cancelled
even if the unit is turned off.
Note on PTY & INFO Search
PTY & INFO Search do not function under the
following conditions:
- FM stations are not preset.
- The signals of the station broadcasting the desired PTY are
weak.
- FM RDS stations cannot be received.
Clock-time (CT)
You can automatically set and update the clock on the hour
every hour just by tuning in an RDS station since RDS stations
transmit clock signals.
1 Press ECO/RDS repeatedly to select "CT ON"
while the unit is on and the time is displayed (see
"Setting the clock").
2 Tune in an RDS station.
To deactivate CT function (If the clock is set wrongly
due to an incorrect clock signal)
Repeat step 1 to select "CT OFF".
Note on RDS features
The RDS features described above may not function correctly
if the RDS transmission data from the station contains too
much interference or the reception signal is too weak.
TAPE PLAYBACK
Notes on cassettes
REV MODE
dTAPE
(REC MUTING)
s
f,g
PUSH
EJECTz
Playback
Use only type I (normal) tapes.
1 Press PUSH EJECTz to open the cassette holder.
2 Insert the tape.
Insert with the exposed side down, and press PUSH
EJECTz to close the cassette holder.
dTAPE
f,g
s
•Use of a tape longer than 90 minutes is not recommended
since they are extremely thin and easily damaged. If you
should use it, do not change the tape operations such as
play and stop frequently.
•Take up any slack in the tape with a pencil or similar tool
before use. Slack tape may get entangled in the deck
mechanism and become damaged.
En
SHIFT
To select a reverse mode
Hold down SHIFT and press REV MODE on the remote
repeatedly.
The mode changes as follows;
"p" : Plays one side only
"[" : Plays from the front side to the back sides once.
"]" : Plays both sides repeatedly
To stop playback
Press s.
To change the playback side
Press dTAPE (REC MUTING) (dTAPE) in playback
mode.
To rewind or fast forward
Press f or g.
3 Press dTAPE (REC MUTING) (dTAPE) to
start play.
Reading the indicators
l: The front side is being played (forward).
j: The back side is being played (reverse).
To reset the tape counter
Press s in stop mode, and the tape counter in the display is
reset to "0000".
Opening and closing the cassette holder will also reset the
tape counter.
To eject the tape
Press PUSH EJECTz after the deck stops completely.
17
TAPE RECORDING
To record radio programs and
external equipment
Use only type I (normal) tapes.
REV MODE
SYNCHRO REC
CD EDIT/
CHECK
REC START/
REC PAUSE
En
s
f,g
s
PUSH
EJECTz
SHIFT
FUNCTION
1 Press PUSH EJECTz to open the cassette holder.
2 Insert the recordable tape.
3 Hold down SHIFT and press REV MODE on the
remote repeatedly to select the reverse mode.
4 Prepare the source.
To record radio programs, press TUNER/BAND and tune
in the desired station.
To record from connected external equipment, press AUX
and prepare the equipment.
To record a CD
Use only type I (normal) tapes.
1 Press PUSH EJECTz to open the cassette holder.
2 Insert the recordable tape.
Insert with the exposed side down, and the side to be
recorded on first facing out from the unit. Press PUSH
EJECTz to close the cassette holder.
3 Hold down SHIFT and press REV MODE on the
remote repeatedly to select the reverse mode.
To record on one side only, select p.
To record on both sides, select [.
If selecting "]" mode in this step, the reverse mode
changes to "[" when starting recording.
4 Press FUNCTION on the remote repeatedly to
select the CD function, and load the disc.
To record only one track, start play of the track.
18
5 Press SYNCHRO REC.
The unit enters the recording pause mode, and "REC"
indicator flashes on the display.
6 Press REC START/REC PAUSE to start recording.
"REC MUTING" flashes in the display for 10 seconds
and recording starts.
When only a track is to be recorded, CD playing returns
to the beginning of the current track and recording starts.
•Volume or tone adjustment(s) (except i-Bass) does not affect
recording.
•i-Bass tone adjustment does affect recording.
•"No Tab" is displayed if you attempt to record a tape with
the tab broken off.
To record a selected set of tracks from a CD
Program the desired tracks (see "Programed play" on page
11) and then press SYNCHRO REC.
5 Press REC START/REC PAUSE twice to start
recording.
When recording input from connected equipment,
manually start playback of the source.
Recording from CDs can also be made in this way.
To do that, start the playback of the CD in step 4.
To stop recording
Press s.
To pause recording (only for TUNER or AUX source)
Press REC START/REC PAUSE. Press again to resume.
To record a 4-second blank space (only for TUNER
or AUX source)
Edited CD recording
Inserting 4-second blank spaces may help you locate the
beginning of the track on other equipment with the "Music
Sensor" function.
AI Edit Recording
Preparation
Prepare a tape that is longer than the CD length.
1 Press d TAPE (REC MUTING) on the unit during
recording or in recording pause mode.
"REC MUTING" flashes in the display for 4 seconds (a
blank space is added) and then the unit enters recording
pause mode.
2 Press REC START/REC PAUSE to resume recording.
When recording a whole CD, AI Edit Recording takes the length
of your tape into account and rearranges the recording order of
the tracks if necessary, so that no track is cut short at the end
of the side.
(AI: Artificial Intelligence)
• Recording cannot start from a point halfway in the tape.
• AI Edit Recording cannot be used with MP3-CDs.
• AI Edit Recording cannot be used with discs containing more
than 30 tracks.
To record a blank space shorter than 4 seconds, press
dTAPE (REC MUTING) again while "REC MUTING"
flashes.
To record a blank space longer than 4 seconds, press
d TAPE (REC MUTING) again after the unit enters
recording pause mode.
Each time the button is pressed, a 4-second blank space is
added.
To erase a tape
1 Insert the tape. Set the tape to the desired point if needed.
2 Press AUX.
If optional equipment is connected to the AUX IN jacks, turn
it off.
3 Press REC START/REC PAUSE twice.
6 Press REC START/REC PAUSE once to start
recording.
The tape is rewound to the beginning of the side facing
out from the unit, "REC MUTING" flashes on the
display and the lead segment is played through for 10
seconds, and recording starts.
When recording on the side facing out from the unit (side
A) finishes, recording on the opposite side (side B) starts.
En
1 Insert the recordable tape.
2 Press FUNCTION on the remote to select the CD
function, and load disc(s).
3 Hold down SHIFT and press CD EDIT/CHECK on
the remote in stop mode.
"AI EDIT" and "AI C--00" is displayed.
4 Press the desired CD slot buttons (1-5) to select
a disc.
When using the remote, press DISC SELECT then press
the numbered button (1-5) within 6 seconds.
5 Press the numbered buttons on the remote to
enter the length of the recordable tape.
10 to 99 minutes can be specified.
- For a 60-minute tape press 6 and 10/0.
In a few seconds, the unit determines the tracks to be
recorded for each side.
•f or g can also be used to specify tape length.
19
Programmed Edit Recording
En
As you program the CD tracks to record, Programmed Edit
Recording displays the remaining recording time for each side
of the tape, so you can easily select a set of desired tracks
within the length of your tape.
• Recording cannot start from a point halfway in the tape.
• Programmed Edit Recording cannot be used with MP3-CDs.
• You cannot program more than 30 tracks.
• You cannot program a track with a track number larger than
30.
1 Insert the recordable tape.
2 Press FUNCTION on the remote to select the CD
function, and load disc(s).
3 Hold down SHIFT and press CD EDIT/CHECK
twice on the remote in stop mode.
"PGM EDIT" and "PRGM C--00" is displayed.
4 Press the desired CD slot buttons (1-5) to select
a disc.
When using the remote, press DISC SELECT then press
the numbered button (1-5) within 6 seconds.
7 Repeat step 6 to select the rest of the tracks for
side A.
The remaining recording time of side A is displayed. You
cannot select a track with a longer playing time.
8 Hold down SHIFT and press CD EDIT/CHECK on
the remote to switch to side B and select the
tracks for the side.
9 Repeat step 6 to select the tracks for side B.
10 Press REC START/REC PAUSE once to start
recording.
The tape is rewound to the beginning of the side facing
out from the unit, "REC MUTING" flashes on the display
and the lead segment is played through for 10 seconds,
and recording starts.
When recording on the side facing out from the unit (side
A) finishes, recording on the opposite side (side B) starts.
To stop recording
Press s. Recording and CD playback stop simultaneously.
To check the program
1 Before recording, hold down SHIFT and press
CD EDIT/CHECK on the remote to select side A or B.
2 Press f or g repeatedly. The track number and
program number are displayed in succession.
To change the program of each side
Hold down SHIFT and press CD EDIT/CHECK on the remote
to select side A or B, and press s to clear the program for
the selected side. Then, select tracks again.
To clear the edit program
Press s twice.
Notes on AI / Programmed Edit Recording
MP3-CDs cannot be used for AI / Programmed Edit Recording.
To prevent accidental erasure
Remove the plastic tab of the cassette tape with a screwdriver
or other pointed tool. To record on the tape again, cover the
detection slot with adhesive tape.
Side A
5 Press the numbered buttons on the remote to
enter the length of the recordable tape.
10 to 99 minutes can be specified.
- For a 60-minute tape press 6 and 10/0.
•f or g can also be used to specify tape length.
6 Press the numbered buttons on the remote to
select the first track to be recorded on side A.
-To select the 25th track, press >10, 2 and 5.
-To select the 11th track, press >10, 1 and 1.
20
Tab for side A
TIMER OPERATIONS
7 Press f or g to select the source (CD, TAPE
and TUNER), and press ENTER.
POWER
POWER
6STANDBY/ON
8 Prepare the source.
TIMER
CLEAR
ENTER
f,g
f,g
SHIFT
SLEEP
Sleep timer
Timer playback
Turns off the unit automatically after a specified time.
Turns on the unit at a specified time for the specified duration.
Make sure the clock is set correctly.
Press SLEEP on the remote.
"SLEEP" flashes in the display.
With each press, the timer duration changes as follows:
AUTO
OFF
90
80
10...70
If you set to "AUTO", the unit turns off automatically when
the current CD or tape finishes playback or elapsed 100
minutes.
To check the remaining time until the unit turns off
Press SLEEP on the remote. The remaining time is displayed
for 6 seconds.
To cancel the sleep timer
Press SLEEP on the remote repeatedly so that "OFF" is
displayed.
1 Press VOLUME +, - to set the volume level.
2 Hold down SHIFT and press TIMER on the remote
repeatedly so that "5" and "TIMER PLAY" is
displayed.
To play CD, load disc(s).
To play a tape, insert the tape.
To play the radio, select the band and tune in the desired
station.
9 Press POWER 6STANDBY/ON (POWER) to turn
the unit off.
"5" remains in the display to indicate the timer standby
mode (when ECO mode is deactivated).
At timer-on time, the unit turns on and plays the selected
source. After the specified timer-activated duration, the
unit turns off again.
•To stop timer setting in steps 4 to 6, press CLEAR.
Timer standby mode is also cancelled.
•The timer playback is not activated when the clock is not
set. ("SET NG" is displayed.)
•Timer playback will not begin unless the unit is turned off
first.
•Timer playback for AUX function is not possible.
3 Within 6 seconds, press ENTER.
"ON TIME" is displayed.
4 Press f or g to set the timer start hour,
and press ENTER.
5 Press f or g to set the minute, and press
ENTER.
"OFF TIME" is displayed.
6 Set the time to stop playback by following the
same procedures as steps 4 and 5.
21
En
Timer recording
Timer recording is available only for TUNER sources.
1 Prepare the recording destination.
Insert the recordable tape in tape deck.
2 Hold down SHIFT and press REV MODE on the
remote to select a reverse mode.
En
To record on one side only, select p.
To record on both sides, select [.
If selecting "]" mode in this step, the reverse mode
changes to "[" when starting recording.
3 Hold down SHIFT and press TIMER on the remote
repeatedly so that "5" and "TIMER REC" are
displayed.
4 Within 6 seconds, press ENTER.
"ON TIME" is displayed.
5 Press f or g to set the timer start hour,
and press ENTER.
6 Press f or g to set the minute, and press
ENTER.
"OFF TIME" is displayed.
7 Set the time to stop playback following the same
procedure as steps 5 and 6.
8 Select the band and tune in the desired station.
9 Insert a recordable tape and then turn the unit
off.
"5" remains in the display to indicate the timer standby
mode (when ECO mode is deactivated).
At timer-on time, the unit turns on and records the selected
source. After the specified timer-activated duration, the
unit turns off again.
22
•To stop timer setting in steps 3 to 6, press CLEAR.
Timer standby mode is also cancelled.
•The timer recording is not activated when the clock is not
set. ("SET NG" is displayed.)
•The timer recording will not begin unless the unit is turned
off first.
To check the timer setting
Hold down SHIFT and press TIMER on the remote repeatedly
so that "TIMER PLAY" or "TIMER REC" appears in the
display.
The timer-on time, the time to stop playback and the source
are displayed for 6 seconds.
To change the timer setting
Reset the timer again.
To cancel the timer
Hold down SHIFT and press TIMER on the remote repeatedly
until "TIMER OFF" is displayed. "5" and "TIMER REC"
disappear from the display.
Tip:
Your timer setting is retained even if the timer is cancelled.
Next time the timer is activated, you can change your previous
setting, or simply use the same setting again.
Notes
•The timer playback performs every day at the specified time
unless you cancel it.
•You cannot set the same time for timer-on time and timeroff time. "SET NG" is displayed if you do that. In this
case, reset the time.
•The timer playback will not begin unless the unit is turned
off first.
REFERENCE
Care and maintenance
Troubleshooting
Occasional care and maintenance of the unit and the software
are needed to optimize the performance of your unit.
If your unit fails to perform properly, check the following guide
and the relevant sections of the Operating Instructions.
First check that the AC power cord and the speakers are
connected correctly and firmly.
Should any problem persist, consult your nearest Aiwa dealer.
To clean the cabinet
Use a soft and dry cloth. If the unit surfaces are extremely
dirty, use a soft cloth lightly moistened with mild detergent
solution. Do not use strong solvents such as alcohol, benzine
or thinner.
To clean the tape heads
Dirty tape heads cause sound deterioration. After every 10
hours of use, clean the tape heads by using a commercially
available dry-type or wet-type head cleaning cassette
separately. Refer to the instructions of the cleaning cassette.
To demagnetize the tape heads
Use a demagnetizing cassette after every 20 to 30 hours of
use. Refer to the instructions of the demagnetizing cassette.
Care of CDs
When a CD becomes dirty, wipe it from the centre out with a
cleaning cloth. Please do not use solvents. After playing a
CD, store it in its case. Do not expose a CD to direct sunlight
or heat sources.
Care of tapes
Store tapes in their cases after use. Do not leave tapes near
magnets, motors, television sets, or any source of magnetism.
Do not expose tapes to direct sunlight, or leave them in a car
parked in direct sunlight.
General
There is no sound
•Are the speakers and AC power cord connected properly?
•Turn VOLUME clockwise and hold.
•The headphones are connected.
•Insert only the stripped portion on the speaker cord into the
SPEAKERS terminal. Inserting the vinyl portion of the
speaker cord will obstruct the speaker connections.
The unit shut off suddenly
•Possibly a short circuit in the speaker terminals. Disconnect
the AC power cord from the AC power socket and reconnect
the speaker cords correctly.
The display blacks out when the unit is turned off.
•ECO is mode set to on. (see "ECO mode" on page 8)
Erroneous display
•Reset the unit. (See "Resetting the unit" on page 24.)
The clock setting/radio presetting/timer is cancelled.
•The AC power cord is disconnected or a power failure occurs
longer than half a day.
Redo the following:
- "Setting the clock" on page 8
- "Preset tuning" on page 14
If you have set the timer, also redo "Timer playback/
recording" on page 21 and 22.
The timer does not function.
•Set the clock correctly.
En
The remote does not function.
•There is an obstacle between the remote and the unit.
•The remote is not pointing in the direction of the unit's
sensor.
•The batteries have run down. Replace the batteries.
Tuner
Poor radio reception
•Check antenna connection. Adjust the antenna to find the
best reception.
•For FM, move the FM antenna to reduce the noise.
•For AM, re-rotate the AM antenna to reduce the noise.
•Move the unit and antenna away from other electric
appliances and cords.
There is severe hum or noise.
•A TV or VCR is placed too close to the stereo system. Move
the stereo system away from the TV or VCR.
The clock indication does not show the correct time.
•A power interruption occurred. Set the clock and timer
settings again.
23
CD player
The sound drops out.
•The lens is dirty. Clean it with a commercially available
blower.
En
The CD does not play.
•The CD is not lying flat in the disc compartment.
•The CD is dirty.
•The CD is inserted label side down.
•Moisture condensation has built up. Remove the CD and
leave the system turned on for about an hour until the
moisture evaporates.
Poor tape sound.
•Use TYPE I (normal) tapes.
Speakers
Sound comes from one channel or unbalanced left
and right volume occurs.
•Check the speaker connection and speaker placement.
Sound lacks bass.
•Check that the speaker's 0 and 9 terminals are connected
correctly.
Tape deck
The tape does not record.
•No tape in the deck.
•The tab has been removed from the cassette tape.
•The tape has reeled to the end.
The tape does not record nor play or there is decrease
in sound level.
•The heads are dirty. Clean them (see "To clean the tape
heads" on page 23).
•The record/playback heads are magnetized. Demagnetize
them (see "To demagnetize the tape heads" on page 23).
The tape does not erase completely.
•The record/playback heads are magnetized. Demagnetize
them (see "To demagnetize the tape heads" on page 23).
There is excessive wow or flutter, or the sound drops
out.
•The capstans or pinch rollers are dirty. Clean them (see "To
clean the tape heads" on page 23).
Noise increases or the high frequencies are erased.
•The record/playback heads are magnetized. Demagnetize
them (see "To demagnetize the tape heads" on page 23).
24
Resetting the unit
If an unusual condition occurs in the display window or the
cassette deck, reset the unit as follows:
1 Press POWER to turn off the power.
If the power cannot be turned off, disconnect the AC power
cord, then plug it in again.
2 Hold down s and press POWER on the main unit.
Everything stored in memory after purchase is cleared.
SPEAKER SYSTEM SX-LMN5
Specifications
Speakers system
MAIN UNIT CX-LMN5
Speaker units
TUNER
FM tuning range
FM usable sensitivity (IHF)
FM antenna terminal
AM tuning range
AM usable sensitivity
AM antenna
87.5 MHz to 108 MHz
16.8 dBf
75 Ω (unbalanced)
531 kHz to 1602 kHz
350 µV/m
Loop antenna
AMPLIFIER
Power output
Input
Outputs
Rated: 64 W + 64 W (6 Ω, T.H.D.
1 %, 1 kHz/DIN 45500)
Reference: 80 W + 80 W (6 Ω, T.H.D.
10 %, 1 kHz/DIN 45324)
AUX IN: 1.4 V
SPEAKERS: 6 Ω or more
PHONES: 32 Ω or more
CASSETTE DECK
Track format
Frequency response
Recording system
Heads
4 tracks, 2 channels stereo
100 Hz – 10000 Hz
AC bias
Recording/playback × 1, erase × 1
Nominal Impedance
Dimensions (w/h/d)
Mass
2 way, Bass-reflex type (magnetic
shielded)
Woofer: 140 mm cone type
Tweeter: 25 mm dome type
6Ω
Approx. 200 × 277 × 279 mm
Approx. 3.6 kg net per speaker
COPYRIGHT
Check copyright laws relevant to recordings from discs, radio
or tape for the country where the unit is to be used.
Licensed by BBE Sound, Inc. under USP4638258, 5510752 and
5736897.
GENERAL
En
Power requirements
230 V AC, 50/60 Hz
Power consumption
85 W
Power consumption in standby mode
with ECO mode on: 0.26 W
with ECO mode off: 15 W
Dimensions (w/h/d)
Approx. 190 × 277 × 353 mm
Mass
Approx. 6.8 kg
Supplied accessories:
FM antenna (1)
AM antenna (1)
Speaker cords (2)
Remote commander (1)
Batteries (2)
Specifications and external appearance are subject to change
without notice.
CD PLAYER
Laser
D/A converter
Signal-to-noise ratio
Wow and flutter
Semiconductor laser (λ = 800 nm)
Emission duration: continuous
1 bit dual
85 dB (1 kHz, 0 dB)
Unmeasurable
25
Sony Corporation
Printed in China
http://www.aiwa.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement