ALCATEL Mobile Phones F200 TRIO User's Manual

In keeping with our environmental preservation and compliance commitment, we include mini-guides in our packaging. More complete instructions and online assistance are available on our website: www.atlinks.com

10. T

In idle/predialing mode: Press to make a call

In Redial list/Call List/Phonebook entry: Press to make a call to the selected entry in the list

During ringing: Press to answer a call

1.2. Handset Overview (Versatis F250 only)

1. M

In idle mode: Press to access the main menu

In sub-menu mode: Press to confirm the selection

During a call: Press to access Intercom/Phonebook/Redial

List/Call List

1.3. Base Station Overview

3. INSTALLING YOUR PHONE

3.1. Installing and Charging the Batteries

1.

2.

3.

4.

Slide down to open the battery compartment cover.

Place the 2 supplied AAA rechargeable batteries as indicated.

Pay extra attention to direction of polarity.

Slide the battery compartment cover back.

Put the handset on the base and charge for 15 hours before using the handset for the first time. The handset will give a beep when it is properly placed on the base or charger.

Notes:

1.

2.

Use only the supplied NiMH rechargeable batteries.

If the handset will not be used for a long time, disconnect and remove the batteries to prevent possible leakage.

1. A

Press A on the base station to page your handset. It will ring for approximately 60 seconds.

Press and hold A on the base station for about five seconds, the base station is entered into registration mode and allows handset registration.

2. , @

Steadily on while the handset is charging or in use. (Applicable only when the LED I/O switch is slid to “I”)

Flash when receiving an incoming call. (Applicable only when the LED I/O switch is slid to “I”)

3. LED I/O SWITCH (Bottom of the Base)

Slide the switch to "O" position to turn off the base LED

Slide the switch to "I" position to turn on the base LED when the handset is charging on the base or in use

3.2. Connecting the Base Station

1.

2.

3.

4.

Plug one end of the telephone line cord into the telephone jack on base bottom.

Plug the small end of power adapter into a power jack on base bottom.

Connect the power supply plug to the base jack horizontally, and route the power supply cord through the slot.

Plug the large end of power adapter into a wall power outlet.

1. GETTING TO KNOW YOUR PHONE

1.1. Handset Overview (Versatis F200 Only)

1.

2.

M

In idle mode: Press to access the main menu

In sub-menu mode: Press to confirm the selection

During a call: Press to access Intercom/Phonebook/Redial

List/Call List

C

In main menu mode: Press to go back to idle screen

In sub-menu mode: Press to go back to previous level

In sub-menu mode: Press and hold to go back to idle screen

In editing/predialing mode: Press to clear a character/digit

In editing/predialing mode: Press and hold to delete all the characters/digits

During a call: Press to mute/unmute the microphone

In idle mode: Press to intercom another handset

In ringing: Press to suppress handset ringer

2.

3.

4.

5.

6.

7.

C

In main menu mode: Press to go back to idle screen

In sub-menu mode: Press to go back to previous level

In sub-menu mode: Press and hold to go back to idle screen

In editing/predialing mode: Press to clear a character/digit

In editing/predialing mode: Press and hold to delete all the characters/digits

During a call: Press to mute/unmute the microphone

In idle mode: Press to intercom another handset

In ringing: Press to suppress handset ringer

+

In idle mode: Press to access the call list

In menu mode: Press to scroll up the menu items

In Phonebook list/Redial list/Call List: Press to scroll up the list

During a call: Press to increase the volume

In ringing: Press to increase the ringer volume

-

In idle mode: Press to access the redial list

In menu mode: Press to scroll down the menu items

In Phonebook list/Redial list/Call List: Press to scroll down the list

During a call: Press to decrease the volume

In ringing: Press to decrease the ringer volume

O

During a call: Press to end a call and go back to idle screen

In menu/editing mode: Press to go back to previous menu

In menu/editing mode: Press and hold to go back to idle screen

In idle mode: Press and hold to power off the handset

In idle mode: Press and hold to power on/off the handset

R

In idle/predialing mode: Press to insert a flash

During a call: Press to dial a flash

P

In idle mode: Press to access the phonebook list

1.4. Display Icons and Symbols

The LCD display gives you information on the current status of the telephone. h j

Steadily on when the handset is in range of the base.

Flash when out of range of the base or not registered to the base.

Steadily on when an intercom is in progress.

Flash when there is an incoming internal call.

k

Indicate a call is in progress.

l x

(Versatis F250 only)

Indicate that handsfree is being used.

Steadily on when an alarm is set.

Flash when the alarm time set before reaches.

a

Indicate that the keypad is locked.

g

Indicate when there are received new Voice Message

Waiting (VMWI) not yet read.

Disappear when all the voice messages have been read.

(Network service dependent) n

Indicate that the ringer is switched off.

5.

6.

Plug the other end of the telephone line cord in to the telephone jack or micro-filter.

Always use the cables provided in the box.

If you have broadband service, a micro-filter (not included) is required.

3.3. Connecting the Charger(s) (for Duo/Trio models)

Plug the power adapter into mains socket.

If you have a Broadband line

If you connect your telephone to a line with a broadband connection, you will need to insert a micro-filter between the telephone and the telephone line, otherwise you may get interference between the telephone and the broadband, which could cause problems.

In a home with broadband, every telephone must have a microfilter connected, not just the one at the telephone point that your modem is connected to. If you need more broadband microfilters, contact your broadband supplier.

3.

4.

5.

6.

7.

+

In idle mode: Press to access the call list

In menu mode: Press to scroll up the menu items

In Phonebook list/Redial list/Call List: Press to scroll up the list

During a call: Press to increase the volume

In ringing: Press to increase the ringer volume

-

In idle mode: Press to access the redial list

In menu mode: Press to scroll down the menu items

In Phonebook list/Redial list/Call list: Press to scroll down the list

During a call: Press to decrease the volume

In ringing: Press to decrease the ringer volume

O

During a call: Press to end a call and go back to idle screen

In menu/editing mode: Press to go back to previous menu

In menu/editing mode: Press and hold to go back to idle screen

In idle mode: Press and hold to power off the handset

In idle mode: Press and hold to power on/off the handset

R

In idle/predialing mode: Press to insert a flash

During a call: Press to dial a flash

P

8.

In idle mode: Press to access the phonebook list

E

In idle mode: Press to access the redial list

9. ALPHANUMERIC KEYPAD, * , #

* key in idle mode: Press and hold to enable or disable the keypad lock

# key in idle mode: Press and hold to turn on/off the ringer

# key in call list mode: Press to review caller’s number if applicable

0 key in predialing/number editing mode: Press and hold to insert a pause

1, 2, 3 key in idle/off hook mode, press and hold to dial the stored direct memory number

8. S

During a call: Press to turn on/off the speakerphone

In Idle mode/Predialing mode/Redial list/Call List/Phonebook entry: Press to make a call with speakerphone

During ringing: Press to answer a call with speakerphone

9. ALPHANUMERIC KEYPAD, * , #

10.

* key in idle mode: Press and hold to enable or disable the keypad lock

# key in idle mode: Press and hold to turn on/off the ringer

# key in call list mode: Press to review caller’s number if applicable

0 key in predialing/number editing mode: Press and hold to insert a pause

1, 2, 3 key in idle/off hook mode, press and hold to dial the stored direct memory number

T

In idle/predialing mode: Press to make a call

In Redial list/Call List/Phonebook entry: Press to make a call to the selected entry in the list

During ringing: Press to answer a call b v

[

Indicate when the battery is fully charged.

Whole icon flashes when the battery performs initial charging.

Internal block icon flashes when the battery is in final charging stage.

Indicate when the battery needs charging.

Flash when low battery power level is detected.

Indicate when more characters are existed before the text currently displayed.

] s

Indicate when more characters are existed after the text currently displayed.

Indicate when new call is received.

Turn off when new call has been read.

f Scroll up/down the menu items/Phonebook list/Redial list/

Call List.

2. PRECAUTIONS

The signal quality will depend on the location and environment of the base and handset.

Position your Versatis F200/Versatis F250 away from sources of excessive heat (radiators, direct sunlight, etc.) and protect it from vibrations and dust. Never allow your telephone to come into contact with water or other liquids, or with aerosols. To reduce the risk of interference and optimize reception, take particular care not to install the base in the immediate vicinity of windows, large metal objects, reinforced concrete, televisions, music centres, VCR or DVD players, halogen lamps or heating devices, fluorescent lighting, burglar alarms, microwave ovens, computers, etc.

This telephone requires an electrical power supply in order to function.

To clean your Versatis F200/Versatis F250, use an antistatic cloth lightly moistened with water.

NB: Your Versatis F200/Versatis F250 is a DECT™* standard appliance designed to receive and transmit telephone calls. It is designed for connection to the public telecommunications network.

www.atlinks.com

ATLINKS Europe

22 quai Gallieni

92150 Suresnes- France

© ATLINKS 2011 - Reproduction prohibited.

The Manufacturer reserves the right to modify the specifications of its products in order to make technical improvements or comply with new regulations.

ALCATEL and ATLINKS are registered trademarks.

The Alcatel logo and Alcatel name are trademarks of Alcatel and used under licence by ATLINKS.

F200/F200 Duo/Trio

F250/F250 Duo/Trio

A/W No.: 10000259 Rev.1 (EN)

Printed in China

4. USING YOUR PHONE

4.1. Make a Call

4.1.1. Preparatory Dialing

Enter the phone number and press

Only) to dial the number. Press

T or S (Versatis F250

C to clear the entry.

4.1.2. Direct Dialing

Press T or S (Versatis F250 Only) to take the line and enter the phone number.

4.1.3. Dial from Direct Memory Keys

In idle or off hook mode, press and hold 1 / 2 / 3 to dial the direct memory number. You have to store number to the related key first. See section 7.4 for reference.

4.1.4. Call from the Redial List

Press

Press

E

T

(Versatis F200 Only) or the redial list and press

or S redial number.

+ / -

(Versatis F250 Only) to access

to select the desired redial number.

(Versatis F250 Only) to dial out to the selected

4.2. Handset Speakerphone (Versatis F250 Only)

During a call, you can press and normal handset use.

S to alternate between handsfree

5. PRIVATE PHONEBOOK

Your phone can store up to 50 private phonebook entries with names and numbers. Each phonebook entry can have a maximum of 20 digits for the phone number and 12 characters for the name. You can also select different ringtones for your phonebook entries. Phonebook entries are stored alphabetically by name.

7.2. Set the Ringer Volume

1.

2.

3.

4.

M

M

M

M

and

and

and

and

+

+

+

+

/

/

/

/

-

-

-

-

to select HS SETTINGS.

to select RING SETUP.

to select RING VOLUME.

to select the desired ringer volume (a total of 6 ringer volume levels including VOLUME OFF).

Note: The respective ringer volume will be played during your

5.

Press

Press

Press

Press selection.

If VOLUME OFF is selected,

Press M to confirm.

n icon will display.

7.3. Adjust Earpiece and Handsfree (Versatis F250

Only) Volume

There are 5 levels (VOLUME 1 to VOLUME 5) to choose from for each of earpiece and handsfree (Versatis F250 Only) volume.

During a call:

Press + / to select volume 1-5. The current setting is shown.

When you end the call, the setting will remain at the last selected level.

7.4. Store Direct Memory Access Number

You can store three direct access numbers into digit KEY 1, KEY

2 and KEY 3, which will be convenient for you to dial to these numbers directly.

1.

2.

3.

4.

5.

Press

Press

Press

Press

M

M

M or edit the number existed before.

M

and

and

and and KEY 3.

Press M

+

+

+

/

/

/

-

-

-

to select HS SETTINGS.

to select DIRECT MEM.

to select any one from KEY 1, KEY 2

and then enter the number you would like to store,

to confirm.

Note: Press and hold 1 , 2 or 3 to call the stored number.

10. TROUBLESHOOTING

If you have difficulty with your phone, please try the suggestions listed below.

As a general rule, if a problem occurs, remove the batteries from all the handsets in your installation for about 1 minute, then disconnect and reconnect the power supply to the base and reinstall the handset batteries.

Problem

No dialing tone when pressing

T key

Cause a. The connection cord of the base station is not plugged in.

b. The adapter cord is not plugged in correctly in the base station.

c. The line is busy, as another handset is used.

d. Wrong connection cord.

Solutions a. Check the connections. Unplug and plug back in the mains. Check that the telephone line cord has been plugged into the base station and the phone socket.

b. Check the base station plug and the

220V plug (remove and plug-in).

c. Wait until the line is unoccupied.

d. Use the original connection cord.

a. Reduce the range.

"OUT OF

RANGE" is displayed.

a. Base station out of range.

b. Base station not connected to mains.

Service not activated or wrong operator.

b. Connect base station to mains.

The call does not work.

Check your Subscription with network.

No display.

Empty battery.

Recharge battery.

The store where you bought your telephone can also provide you with information and after-sales support.

5.1. Add a New Phonebook Entry

In idle:

1. Press

2.

3.

4.

5.

6.

OR

Press and then press

Press

Press

Press

Press

P

M

M

M

M

M

to access the phonebook.

and

and

+

+

/

/

-

M

-

to select PHONEBOOK main menu item

to access the phonebook.

to select ADD.

to enter the name.

to enter the number.

to select the desired ringtone for your phonebook entry.

Press M to store the phonebook entry.

5.2. Call from the Phonebook

In idle:

1. Press

2.

OR

Press

Press

P

M and then press

T

to access the phonebook.

and

or

+

M

S

/ to select PHONEBOOK main menu item

to access the phonebook.

(Versatis F250 Only) to dial out to the selected phonebook entry.

6. CALLER DISPLAY (NETWORK DEPENDENT)

This feature is available if you have subscribed the Caller Line

Identification service with your telephone service provider. Your phone can store up to 20 received calls with date/time information in the Call List. The number will be shown on the LCD when the phone is ringing. If the number matches with one of the entries in your

Private Phonebook, the caller’s name stored in the private phonebook will be displayed alternatively with the number. The handset will ring with the melody associated with that phonebook entry.

If the caller number is disabled to send caller information,

“WITHHELD” will display.

If the caller number is not provided, “OUT OF AREA” will display.

In standby, if three unanswered calls are received, “3 NEW

CALLS” will be displayed.

8. REGISTRATION

Your handset and base station is pre-registered. Up to five handsets can be registered to a single base station.

If for some reason, the handset is not registered to the base station ( h flashes even when the handset is near the base station), register your handset according to the following procedure.

1.

2.

3.

4.

5.

Press and hold the base station is entered into registration mode.

Press

Press

M

M

and

A

+ /

on the base station for about five seconds,

to select REGISTRATION.

and you are requested to enter the 4-digit system

PIN (default PIN is 0000).

Enter the 4-digit system PIN.

Press M to confirm.

If the handset registration is successful, you will hear a confirmation tone and the h will stop flashing. The handset will automatically be allocated the next available handset number.

This handset number is shown in the handset display in standby mode. If the handset registration is unsuccessful, the flash.

h will still

11. SAFETY

In the event of an electrical hazard, the mains adapter acts as

230V power isolating device. It should therefore, as a precaution, be installed close to the appliance and be easily accessible. To disconnect the device from the primary power source, the mains adapter must be removed from the 230V AC/50 Hz socket.

If the mains adapter fails, it must be replaced by an identical model.

If not connected to the mains power or if there is a mains power failure, telephones that use cordless handsets will not work.

You will then be unable to make or receive calls in the event of an emergency.

This is why we recommend that you also keep a conventional telephone – one that doesn’t require a power supply – as a backup.

! Do not use your telephone to notify a gas leak when standing in the vicinity of the leak.

It is recommended that you avoid using this device during electrical storms.

Do not attempt to open the batteries, as they contain chemical substances. In the event of leakage, avoid contact with the skin, eyes, nose and mouth. In the event of contact, rinse the affected part for about twenty minutes with running water and seek urgent medical attention. Clean the product with absorbent paper or a dry cloth and contact your reseller for replacement batteries.

ATLINKS hereby declares that the following models conform to the essential requirements and other applicable provisions of

European directive 1999/5/EC.

Versatis F200/Versatis F200 Duo/Trio

Versatis F250/Versatis F250 Duo/Trio

6.1. View the Call List

All received calls are saved in Call List with the latest call putting at the top of the list. When the call list is full, the oldest call will be replaced by a new call. The unanswered call which has not been read is marked with a the display.

s at the centre of the bottom line of

1.

2.

3.

Press

OR

Press

Press

Press

+ to access the call list.

M

+ /

and

-

+ / to select CALL LIST.

to select the desired entry.

# to view the caller’s number if applicable.

6.2. Call from the Call List

In idle:

1. Press

2.

OR

Press

Press

+ to access the call list.

M

T

and

or

+

S

/ to select CALL LIST.

(Versatis F250 Only) to dial out to the selected phonebook entry.

7. PHONE SETTINGS

7.1. Set the Ringer Melody for Internal/External Calls

1.

2.

3.

4.

5.

Press

Press

Press

Press

M and + / to select HS SETTINGS.

M and + / to select RING SETUP.

M and + / to select INT RING or EXT RING.

M and + / to select the desired ringer melody from the melody list.

Note: The respective ringer melody will be played while browsing the melody list.

Press M to confirm.

9. TECHNICAL DETAILS

Free Field Range

Indoor Range

Handset Battery Life

(average values)

Number of Handsets

Intercom Mode

Three-Way Conference

(1 outside correspondent +

2 internal correspondents)

Electrical Connection/Base

Mains Adaptor/Charger

Up to 300 metres*

Up to 50 metres*

10 hours talk time**

100 hours standby**

Up to 5

Yes

Yes

Telephone Connection

Batteries

Operating Temperature

Base main adaptor:

Model No.: S004LV0600030

Input: 100-240 V/50-60 Hz/0.15 A

Output: 6 V DC/300 mA

Charger adaptor:

Model No.: S004LV0600030

Input: 100-240 V/50-60 Hz/0.15 A

Output: 6 V DC/300 mA

Only use the adaptors supplied with the telephone

Single-phase AC, excluding

IT installations defined by the

EN60950 standard.

Caution: The network voltage is classified as a hazard by the criteria of this standard.

Appliance designed for connection to a TNV3 class

(telecommunications network voltage) analogue telephone line as defined by the EN60950 standard.

AAA – 1.2 V – 400 mA

Only use the batteries supplied with the telephone.

Use any other type of battery presents a risk of explosion.

Used batteries must be disposed of in compliance with current environmental protection regulations.

From 5°C to 40°C

* Values may vary according to environment.

** Depending on initial battery charge.

12. ENVIRONMENT

This symbol means that your inoperative electronic appliance must be collected separately and not mixed with the household waste. The European Union has implemented a specific collection and recycling system for which producers are responsible.

This appliance has been designed and manufactured with high quality materials and components that can be recycled and reused. Electrical and electronic appliances are liable to contain parts that are necessary in order for the system to work properly but which can become a health and environmental hazard if they are not handled or disposed of in the proper way. Consequently, please do not throw out your inoperative appliance with the household waste.

If you are the owner of the appliance, you must deposit it at the appropriate local collection point or leave it with the vendor when buying a new appliance.

- If you are a professional user, please follow your supplier's instructions.

- If the appliance is rented to you or left in your care, please contact your service provider.

Keen to preserve the environment, ATLINKS has equipped this appliance with a switching power supply, offering better energy efficiency. The advantages include not only very low electricity consumption, but also a more compact format than the conventional power supply units used by the previous range.

The used batteries from your telephone (if it has batteries) must be disposed of in compliance with current environmental protection regulations. Comply with your local regulations.

Return your batteries to your reseller or dispose of them at an approved recycling centre.

Help us protect the environment in which we live!