Power Pack Hood Liner
INSTALLATION INSTRUCTIONS
Power Pack Hood Liner
Intended for Domestic Cooking Only
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with homeowner
Homeowner: Use and Care Information inside
Prestige America - 103 Fairfield Rd. Fairfield, NJ 07004
Table of Contents
Important Safety Instructions....................................................1 - 2
Installation Instructions.............................................................2 - 3
Hood Operating Instructions..........................................................3
Cleaning Instructions.....................................................................4
Cleaning the Hood Surface...........................................................4
Rear-Ducting Instructions..............................................................5
Warranty Information.....................................................................5
Hood Insert Specs (0, S, & UIM Models).................................6 - 8
PRESTIGE PRODUCTS DIVISION
Signature Marketing Group LTD.
103 Fairfield Road
Fairfield, NJ 07004
1-800-358-8886
IMPORTANT SAFETY INSTRUCTIONS
PRESTIGE HOODS ARE FOR RESIDENTIAL USE ONLY!
CAUTION: FOR GENERAL VENTILATION USE ONLY. DO NOT USE TO
EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS
1. Use this unit only in the manner intended by the manufacturer. (If you have questions, contact the
manufacturer at 800-358-8886.
2. Before servicing or cleaning the unit, switch power off at service panel and lock the panel to prevent power from being switched on accidentally. When the service panel cannot be locked, securely
fasten a prominent warning device, such as a tag, to the service panel.
WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings, boil overs can cause smoking and may
ignite. Heat oils slowly on low heat.
b) Always turn hood ON when cooking.
c) Clean ventilating filters frequently. DO NOT ALLOW GREASE TO ACCUMULATE ON FAN OR
FILTER.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING - IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
a) Smother flames with a close fitting lid, cooking sheet, or other metal tray, then turn off the burner.
BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND
CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion may result.
-1-
d) Use an extinguisher only if:
1) You know you have a class ABC extinguisher and you already know how to operate it.
2) The fire is small and contained in the area where it started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
INSTALLATION INSTRUCTIONS
NOTE: THE DESIRED INSTALLATION HEIGHT OF THE HOOD IS AT THE DISCRETION OF
THE USER, HOWEVER, A HEIGHT OF 30” TO 36” ABOVE THE COOKING SURFACE
IS RECOMMENDED. TWO PERSONS ARE REQUIRED TO INSTALL HOOD.
BEFORE INSTALLING YOUR INSERT, BE SURE TO READ THE FOLLOWING!
*Either an interior, in-line, or remote blower may be used with Prestige hood liners and power packs.
Other blowers CANNOT be substituted. Select the series best suited for your application. Units labeled “LINERS” are for use with in-line blowers or remote blowers. Units labeled “POWER PACKS”,
come with pre-installed 600 (S1) or 1200 (S2) CFM blowers. Before installing ANY unit, inspect and
test blowers to ensure there is no packing or obstructions remaining in the unit and that the blower(s)
spin freely.
PARTS SOLD SEPARATELY
- In-line blowers IL600, IL1000, IL1200, and IL1600
- Remote blowers RB1000, RB1200, RB1600, RB2000
- Transitions TR6x15/8RD, TR6x15/10RD (for use with S2 blower system), TRC8/6 transitions collar
(for use with S1 blower system.)
- Wall Caps WC6HD, WC8HD, WC10HD. The WC6x15/HD is for use with the S2 blower system
when rear ducting.
- Roof Caps RC6 sn RC10 will accommodate 6” to 10” round duct sizes.
- Backdraft damper BD8 or BD10 (in-line 8” or 10” section duct with backdraft damper installed).
- Wall switch kit UIBWSK controls both lights and fan(s) in lieu of unit switches.
NOTE: DURING INSTALLATION, PROTECT COUNTERTOP AND/OR COOKING APPLIANCES.
-2-
The custom hood frame must be sized to the shape and total weight of the insert assembly. (See
hood liner/insert dimension guide.) Run power cable to the installation location. Stub out a 4 foot
length of electrical cable behind the custom hood. DETERMINE WHETHER OR NOT THE USE OF A
WALL SWITCH IS NEEDED. A 3” to 4” recess should be provided to allow for a proper capture area.
If the cooking product contains a grill (BBQ), a minimum of a 6” capture area should be provided. The
custom hood depth should be at 19” minimum for common gas or electric cooktops. A 22” depth of
hood is recommended for upscale or pro-style gas or electric cooktops. A 24” depth is to be provided
for use with pro-style ranges, whether dual-fuel or all-gas. If the cooking appliance contains a grill
(BBQ) or a high output wok or griddle, the use of an in-line blower or remote blower is highly
recommended.
NOW THAT YOU HAVE READ THESE PRECAUTIONS, YOU MAY CONTINUE TO
THE INSTALLATION INSTRUCTIONS.
1.) Choose an installation height comfortable for the user. IMPORTANT: Most building codes require a
30” clearance from the top of a surface burner to the underside of any combustible material.
2.) Choose the appropriate cut-out dimension from enclosed planning guide. Mark the underside of
the wood hood, alcove, or hearth making sure you leave adequate clearance for the stainless steel
trim overlay and body of hood liner. Cut along your marked line.
3.) Caution: SWITCH OFF POWER AT SERVICE PANEL. Insert 115 volt line though the 7/8” hole that
is punched through the back of the unit and attach with the appropriate ROMEX or BX connector.
4.) Attach the metal duct to the unit either directly to the collar provided or by using a duct transition.
See chart B. NOTE: USE RIGID METAL DUCTWORK ONLY. DO NOT USE FLEXIBLE METAL OR
PLASTIC DUCT. FLOW RESTRICTIONS AND GREASE BUILD UP WILL OCCUR.
5.) Lift hood liner into position. Fasten to underside of wood hood, alcove, or hearth with appropriate
fastener. Make certain the unit is fastened securely to prevent vibration.
6.) Complete the electrical connection in the junction box inside the hood. If equipped with internal
fan check to be certain that the fan blade turns freely by hand and there are no packing materials or
other obstructions in the motor housing. Also, make sure light bulbs are tightly screwed into sockets.
7.) Install stainless steel filters by sliding filters into the top channel then down into lower channel.
8.) Turn on power at service panel.
HOOD OPERATING INSTRUCTIONS
The blower should be turned on for about 5 minutes BEFORE cooking in order to establish air currents
upward through the hood. Use the low speeds for normal use and the higher speeds for strong odors or
fumes. Minimize drafts across the range or cooktop, they will reduce the effectiveness of the hood.
-3-
CLEANING INSTRUCTIONS
Be sure lights are cool before cleaning your hood. Filters should be washed in the dishwasher or by
hand at least once every 24 hours of use or 2 weeks, whichever is shorter.
1) Turn the fan and lights off.
2) Push the filters towards the top and extract downward.
3) When placing filters into a dishwasher be sure that the filters are angled.
4) Drain water and let each filter dry before replacing.
TO CLEAN HOOD SURFACE
Do not use abrasive products. For general care, wipe the outside of the stainless steel
with sudsy water or household cleaners. Rinse well and dry with clean soft cloth to avoid
water marks. Wipe and dry brushed stainless steel in the same direction as the grain.
To remove fingerprints and give added shine, use a commercial grade stainless steel
cleaner.
Cleaning & Maintenance
Cleaning Baffle Filter
*All Prestige stainless baffle filters are
dishwasher safe. You may also hand
wash the filters in warm soapy water.
FILTER
-4-
REAR DUCTING INSTRUCTIONS
In some cases you will not be able to duct the unit to the top.
In that case, rear-ducting is necessary.
1) Lay insert on its face on top of a soft, non-abrasive blanket.
2) Remove the screws from the L-Bracket on the blower assembly. *DO NOT LOSE SCREWS!*
3) Disconnect motor wires from terminal block.
4) Flip the unit so the exit hole is facing the back of the unit.
5) Re-apply the screws to the L-Bracket on the blower assembly.
6) Be sure that your unit is secure and in place and available for ducting through the back.
* Models labeled UIM CANNOT be rear ducted.
WARRANTY INFORMATION
Prestige Remote Blowers are warranteed to be free
from defects in materials and workmanship,
under normal household use for a period of :
ONE (1) YEAR
Prestige will warranty all parts and related labor to replace them, during the one (1) year warranty
period. This applies to the actual parts and normal labor and excludes all other costs, removal and reinstallation. Items NOT covered in the warranty include: light bulbs, items fabricated to customer design,
consequential damage removal & reinstallation, abnormal travel outside the service area, including but
not limited to: remote area transport, ferries, or excessive mileage. If any of these situations apply, the
customer will be responsible for payment in full of said exclusion.
The main motor is warranteed for a period of :
FIVE (5) YEARS
Prestige will replace any motor that fails within the
five (5) year warranty, free of charge, on product when
it is located within the United States. This applies
only to the motor itself and excludes all other costs,
including labor, removal and re-installation.
This warranty does not apply to damage resulting from commercial use, abuse,
accident, natural disasters or electrical surge to the unit.
Prestige will not be responsible for consequential damages.
-5-
Additional Information:
-D-
Side View
-GBox Dimensions Overall minus flange
E
A
B
C
D
Model
12
11
3 8 1/2
22-S1 22
10
15
14
3
28-S1 28
10
15
14
3
34-S1 34
10
15
14
3
30-S2 30
10
34
15
14
3
34-S2
10
15
14
3
40-S2 40
10
18
14
3
46-S2 46
10
18
14
3
52-S2 52
10
18
14
3
58-S2 58
S2 Unit - Dual Duct
-F-
F
10 1/2
13 1/2
13 1/2
13 1/2
13 1/2
13 1/2
16 1/2
16 1/2
16 1/2
- Electrical connection is located in the center of
the back of the unit 4” from the base.
- Single Duct exit is 6” Round.
- Ducting Recommendation for S1 Models: For Duct Run 10’ or
less 6” Round Duct. For Duct Run over 10’ use 8” Round Duct.
Transition included. For S2 Models: For Duct Run 10’ or less
8” Round Duct. Over 10’ use 10” Round Duct.
-C-
-E-
G
20 1/2
25 1/4
31 1/4
32 1/2
31 1/4
37 1/4
44 3/4
55 3/4
56 3/4
-J-
S-1 Back
View
H
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
-I-
I
5
14
17
17
17
20
23
26
29
-K-
-L-
-AOverall Dimensions
J
K
L
2 1/2
6
12 1/2
2 1/2
6
18
2 1/2
6
24
2 1/2 12 1/2
24
2 1/2 12 1/2
24
2 1/2 12 1/2
30
2 1/2 12 1/2
20
2 1/2 12 1/2
26
2 1/2 12 1/2
32
Electrical
Connection
-H-
-B-
-I-
-H-
-F-
Electrical
Connection
S1 Unit - Single Duct
-K-
Cutout Dimension
20 5/8 x 10 5/8
25 3/4 x 13 5/8
31 3/4 x 13 5/8
28 5/8 x 13 5/8
37 3/4x 13 5/8
37 3/4 x 13 5/8
45 1/4 x 16 5/8
57 3/4 x 16 5/8
57 1/4 x 16 5/8
Transition Size
INCLUDED**
INCLUDED**
INCLUDED**
TR6x15/8 or /10
TR6x15/8 or /10
TR6x15/8 or /10
TR6x15/8 or /10
TR6x15/8 or /10
TR6x15/8 or /10
-GBox Dimensions Overall minus flange
-J-
S-2 Back
View
-L-
Hood Insert Specifications Guide (S Models)
Model
28-0
34-0
40-0
46-0
52-0
58-0
A
28
34
40
46
52
58
B
15
15
15
18
18
18
C
15
15
15
18
18
18
D
25 1/4
31 1/4
37 1/4
44 3/4
50 3/4
56 3/4
Box Dimensions
Overall minus
flange
Front View
-D-
E
13 1/2
13 1/2
13 1/2
16 1/2
16 1/2
16 1/2
-F-
-H-
-J-
F
10
10
10
10
10
10
-G-
-I-
G
8
8
8
13
13
13
H
28
28
28
N/A
N/A
N/A
-E-
I
3/4
3/4
3/4
N/A
N/A
N/A
electrical box
-L-
J
3/4
3/4
3/4
N/A
N/A
N/A
-C-
-K-
K
13 1/2
13 1/2
13 1/2
16 1/2
16 1/2
16 1/2
-A-
L
7
7
7
7
7
7
Side View
Cutout Dimension
25 3/4 x 13 5/8
31 3/4 x 13 5/8
37 3/4 x 13 5/8
45 1/4 x 16 5/8
51 1/4 x 16 5/8
57 1/4 x 16 5/8
-B- Overall Dimensions
Transition Size
10” Round Starter Collar
10” Round Starter Collar
10” Round Starter Collar
10” Round Starter Collar
10” Round Starter Collar
10” Round Starter Collar
- Starter Collar Included
in Unit.
Additional Information
Hood Insert Specifications Guide (-0 Models)
Hood Insert Specifications Guide (UIM Models)
*UIM Models are shown individually.*
5
10
9
Side View
All UIM
Models
3/4
11 1/2
10 1/2
1 1/4
UIM 20 1/2 S1
Front View
3
3/4
19
20 1/2
18
UIM 28 S1
Front View
9
10 1/4
26 1/2
28
18
UIM 28 S2
Front View
26 1/2
28
Model Cutout Dimension
Transition Size
20-S1
19”W x 10”D
6” Round*TRC8/6
28-S1
26 1/2”W x 10”D
6” Round*TRC8/6
28-S2 28”W x 11 1/2”D x 10 1/4”H TR6x15/8 or TR6x15/10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement