Instruction Manual - GE Grid Solutions

Instruction Manual - GE Grid Solutions
Digital Energy
Instruction Manual
Software Revision: 1.10
Manual P/N: 1601-0266-A1
Manual Order Code: GEK-113584
Copyright © 2011 GE Digital Energy
RE
ISO9001:2000
G
EM
Canada L6E 1B3
I
N
215 Anderson Avenue, Markham, Ontario
U LT I L
GE Multilin's Quality
Management System is
registered to ISO9001:2000
Tel: (905) 294-6222 Fax: (905) 201-2098
Internet: http://www.GEmultilin.com
*1601-0215-A1*
D
T
GIS ERE
GE Digital Energy
QMI # 005094
LISTED
This product cannot be disposed of as unsorted municipal waste in the European
union. For proper recycling return this product to your supplier or a designated
collection point. For more information go to www.recyclethis.info .
Table of Contents
1: THREE-PHASE
POWER
MEASUREMENT
THREE-PHASE SYSTEM CONFIGURATIONS ........................................................................... 1-2
DELTA CONNECTION ........................................................................................................... 1-4
BLONDELL’S THEOREM AND THREE PHASE MEASUREMENT ......................................... 1-6
POWER, ENERGY AND DEMAND ............................................................................................... 1-8
REACTIVE ENERGY AND POWER FACTOR ............................................................................. 1-11
HARMONIC DISTORTION .............................................................................................................. 1-13
POWER QUALITY .............................................................................................................................. 1-16
2: METER OVERVIEW
AND
SPECIFICATIONS
MULTILIN™ EPM7000 METER OVERVIEW ............................................................................. 2-1
VOLTAGE AND CURRENT INPUTS ...................................................................................... 2-2
ORDERING INFORMATION ................................................................................................... 2-3
SOFTWARE OPTIONS (SEE ABOVE) ..................................................................................... 2-3
MEASURED VALUES ............................................................................................................ 2-4
UTILITY PEAK DEMAND ....................................................................................................... 2-5
SPECIFICATIONS ............................................................................................................................... 2-7
COMPLIANCE ........................................................................................................................ 2-10
3: MECHANICAL
INSTALLATION
INTRODUCTION ................................................................................................................................ 3-1
ANSI INSTALLATION STEPS .......................................................................................................... 3-3
DIN INSTALLATION STEPS ............................................................................................................ 3-4
4: ELECTRICAL
INSTALLATION
CONSIDERATIONS WHEN INSTALLING METERS ................................................................. 4-1
CT LEADS TERMINATED TO METER ........................................................................................... 4-3
CT LEADS PASS THROUGH (NO METER TERMINATION) ................................................... 4-4
QUICK CONNECT CRIMP-ON TERMINATIONS ..................................................................... 4-5
VOLTAGE AND POWER SUPPLY CONNECTIONS ................................................................ 4-6
GROUND CONNECTIONS .............................................................................................................. 4-7
VOLTAGE FUSES ............................................................................................................................... 4-8
ELECTRICAL CONNECTION DIAGRAMS .................................................................................. 4-9
5: COMMUNICATION
INSTALLATION
MULTILIN™ EPM7000 METER COMMUNICATION .............................................................. 5-1
IRDA PORT (COM 1) .......................................................................................................... 5-1
RS485 / KYZ OUTPUT (COM 2) ..................................................................................... 5-1
ACCESSING THE METER IN DEFAULT COMMUNICATION MODE ................................. 5-5
CONNECTING TO THE METER THROUGH GE COMMUNICATOR EXT ......................... 5-6
MULTILIN™ EPM7000 METER DEVICE PROFILE SETTINGS ............................................ 5-9
6: USING THE
MULTILIN™
EPM7000 METER
INTRODUCTION ................................................................................................................................ 6-1
UNDERSTANDING METER FACE ELEMENTS ..................................................................... 6-1
UNDERSTANDING METER FACE BUTTONS ....................................................................... 6-2
USING THE FRONT PANEL ............................................................................................................ 6-3
UNDERSTANDING STARTUP AND DEFAULT DISPLAYS .................................................... 6-3
USING THE MAIN MENU .................................................................................................... 6-4
USING RESET MODE ........................................................................................................... 6-4
EPM7000 - POWER QUALITY METER – USER GUIDE
TOC–1
ENTERING A PASSWORD ..................................................................................................... 6-5
USING CONFIGURATION MODE ......................................................................................... 6-6
USING OPERATING MODE .................................................................................................. 6-12
UNDERSTANDING THE % OF LOAD BAR ............................................................................... 6-13
PERFORMING WATT-HOUR ACCURACY TESTING (VERIFICATION) ............................. 6-14
7: USING THE I/O
OPTION CARDS
OVERVIEW ........................................................................................................................................... 7-1
INSTALLING OPTION CARDS ....................................................................................................... 7-2
CONFIGURING OPTION CARDS .................................................................................................. 7-3
1MA OUTPUT CARD (C1) ............................................................................................................... 7-4
SPECIFICATIONS ................................................................................................................... 7-4
DEFAULT CONFIGURATION ................................................................................................. 7-4
WIRING DIAGRAM ............................................................................................................... 7-5
20MA OUTPUT CARD (C20) .......................................................................................................... 7-6
SPECIFICATIONS ................................................................................................................... 7-6
DEFAULT CONFIGURATION ................................................................................................. 7-6
WIRING DIAGRAM ............................................................................................................... 7-7
DIGITAL OUTPUT (RELAY CONTACT) / DIGITAL INPUT CARD (RS1) ............................. 7-8
SPECIFICATIONS ................................................................................................................... 7-8
WIRING DIAGRAM ............................................................................................................... 7-9
PULSE OUTPUT (SOLID STATE RELAY CONTACTS) / DIGITAL INPUT CARD (PS1) .. 7-10
SPECIFICATIONS ................................................................................................................... 7-10
DEFAULT CONFIGURATION: ................................................................................................ 7-11
WIRING DIAGRAM ............................................................................................................... 7-11
FIBER OPTIC COMMUNICATION CARD (F1; F2) .................................................................... 7-12
SPECIFICATIONS ................................................................................................................... 7-12
WIRING DIAGRAM ............................................................................................................... 7-13
10/100BASET ETHERNET COMMUNICATION CARD (E1) ................................................. 7-14
SPECIFICATIONS ................................................................................................................... 7-14
DEFAULT CONFIGURATION ................................................................................................. 7-14
WIRING DIAGRAM ............................................................................................................... 7-15
8: USING THE
ETHERNET CARD
OVERVIEW ........................................................................................................................................... 8-1
HARDWARE CONNECTION .......................................................................................................... 8-2
PERFORMING NETWORK CONFIGURATION ......................................................................... 8-3
ETHERNET CARD FEATURES ........................................................................................................ 8-4
ETHERNET COMMUNICATION ............................................................................................. 8-4
EMBEDDED WEB SERVER ................................................................................................... 8-4
NTP TIME SERVER SYNCHRONIZATION ............................................................................ 8-9
9: DATA LOGGING
OVERVIEW ........................................................................................................................................... 9-1
AVAILABLE LOGS .............................................................................................................................. 9-2
APPENDIX A:
MULTILIN™
EPM7000 METER
NAVIGATION MAPS
INTRODUCTION ................................................................................................................................ A-1
NAVIGATION MAPS (SHEETS 1 TO 4) ........................................................................................ A-2
TOC–2
EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B:
MODBUS MAP AND
RETRIEVING LOGS
INTRODUCTION ................................................................................................................................ B-1
MODBUS REGISTER MAP SECTIONS ........................................................................................ B-2
DATA FORMATS ................................................................................................................................ B-3
FLOATING POINT VALUES ............................................................................................................ B-4
RETRIEVING LOGS USING THE EPM7000 METER'S MODBUS MAP ............................. B-5
DATA FORMATS ................................................................................................................... B-5
EPM7000 METER LOGS ................................................................................................... B-5
BLOCK DEFINITIONS ............................................................................................................ B-7
LOG RETRIEVAL .................................................................................................................... B-14
LOG RECORD INTERPRETATION ......................................................................................... B-22
EXAMPLES ............................................................................................................................. B-28
IMPORTANT NOTE CONCERNING THE EPM7000 METER'S MODBUS MAP ............. B-33
HEX REPRESENTATION ........................................................................................................ B-33
DECIMAL REPRESENTATION ................................................................................................ B-33
MODBUS REGISTER MAP (MM-1 TO MM-32) ........................................................................ B-34
APPENDIX C:
DNP MAPPING
OVERVIEW ........................................................................................................................................... C-1
PHYSICAL LAYER .............................................................................................................................. C-2
DATA LINK LAYER ............................................................................................................................. C-3
APPLICATION LAYER ....................................................................................................................... C-4
ERROR REPLY ..................................................................................................................................... C-5
THE REGISTER MAP FOR THE EPM7000 METER’S DNP VERSION ................................ C-6
DNP MESSAGE LAYOUTS .............................................................................................................. C-10
INTERNAL INDICATION BITS ........................................................................................................ C-12
APPENDIX D:
USING THE USB TO
IRDA ADAPTER
(CAB6490)
INTRODUCTION ................................................................................................................................ D-1
INSTALLATION PROCEDURES ..................................................................................................... D-2
EPM7000 - POWER QUALITY METER – USER GUIDE
TOC–3
TOC–4
EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 1: Three-Phase Power
Measurement
Three-Phase Power Measurement
This introduction to three-phase power and power measurement is intended to provide
only a brief overview of the subject. The professional meter engineer or meter technician
should refer to more advanced documents such as the EEI Handbook for Electricity
Metering and the application standards for more in-depth and technical coverage of the
subject.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–1
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.1
Three-Phase System Configurations
Three-phase power is most commonly used in situations where large amounts of power
will be used because it is a more effective way to transmit the power and because it
provides a smoother delivery of power to the end load. There are two commonly used
connections for three-phase power, a wye connection or a delta connection. Each
connection has several different manifestatWye Connection
The wye connection is so called because when you look at the phase relationships and the
winding relationships between the phases it looks like a Y. Figure 1.1 depicts the winding
relationships for a wye-connected service. In a wye service the neutral (or center point of
the wye) is typically grounded. This leads to common voltages of 208/120 and 480/277
(where the first number represents the phase-to-phase voltage and the second number
represents the phase-to-ground voltage).
A
Ia
Van
B
Vbn
Vcn
N
C
FIGURE 1–1: Figure 1.1: Three-phase Wye Winding
1–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
The three voltages are separated by 120o electrically. Under balanced load conditions the
currents are also separated by 120o. However, unbalanced loads and other conditions can
cause the currents to depart from the ideal 120o separation. Three-phase voltages and
currents are usually represented with a phasor diagram. A phasor diagram for the typical
connected voltages and currents is shown in Figure 1.2.
Vcn
Ic
Van
Ia
Ib
Vbn
Figure 1.2: Phasor Diagram Showing Three-phase Voltages and Currents
The phasor diagram shows the 120o angular separation between the phase voltages. The
phase-to-phase voltage in a balanced three-phase wye system is 1.732 times the phaseto-neutral voltage. The center point of the wye is tied together and is typically grounded.
Table 1.1 shows the common voltages used in the United States for wye-connected
systems.
Table 1–1: Common Phase Voltages on Wye Services
Phase to Ground Voltage
Phase to Phase Voltage
120 volts
208 volts
277 volts
480 volts
2,400 volts
4,160 volts
7,200 volts
12,470 volts
7,620 volts
13,200 volts
Usually a wye-connected service will have four wires: three wires for the phases and one
for the neutral. The three-phase wires connect to the three phases (as shown in Figure 1.1).
The neutral wire is typically tied to the ground or center point of the wye (refer to Figure
1.1).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–3
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
In many industrial applications the facility will be fed with a four-wire wye service but only
three wires will be run to individual loads. The load is then often referred to as a deltaconnected load but the service to the facility is still a wye service; it contains four wires if
you trace the circuit back to its source (usually a transformer). In this type of connection
the phase to ground voltage will be the phase-to-ground voltage indicated in Table 1, even
though a neutral or ground wire is not physically present at the load. The transformer is the
best place to determine the circuit connection type because this is a location where the
voltage reference to ground can be conclusively identified.
1.1.1
Delta Connection
Delta-connected services may be fed with either three wires or four wires. In a three-phase
delta service the load windings are connected from phase-to-phase rather than from
phase-to-ground. Figure 1.3 shows the physical load connections for a delta service.
A
Ia
Iab
Vab
Vca
B
Ib
Ica
Vbc
C
Ibc
Ic
FIGURE 1–2: Figure 1.3: Three-phase Delta Winding Relationship
In this example of a delta service, three wires will transmit the power to the load. In a true
delta service, the phase-to-ground voltage will usually not be balanced because the
ground is not at the center of the delta.
Figure 1.4 shows the phasor relationships between voltage and current on a three-phase
delta circuit.
In many delta services, one corner of the delta is grounded. This means the phase to
ground voltage will be zero for one phase and will be full phase-to-phase voltage for the
other two phases. This is done for protective purposes.
1–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
Vca
Ic
Vbc
Ia
Ib
Vab
FIGURE 1–3: Figure 1.4: Phasor Diagram, Three-Phase Voltages and Currents, Delta-Connected
Another common delta connection is the four-wire, grounded delta used for lighting loads.
In this connection the center point of one winding is grounded. On a 120/240 volt, fourwire, grounded delta service the phase-to-ground voltage would be 120 volts on two
phases and 208 volts on the third phase. Figure 1.5 shows the phasor diagram for the
voltages in a three-phase, four-wire delta system.
Vca
Vnc
120 V
Vbc
120 V
Vbn
Vab
FIGURE 1–4: Figure 1.5: Phasor Diagram Showing Three-phase Four-Wire Delta-Connected System
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–5
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.1.2 Blondell’s Theorem and Three Phase Measurement
In 1893 an engineer and mathematician named Andre E. Blondell set forth the first
scientific basis for polyphase metering. His theorem states:
If energy is supplied to any system of conductors through N wires, the total power in the
system is given by the algebraic sum of the readings of N wattmeters so arranged that
each of the N wires contains one current coil, the corresponding potential coil being
connected between that wire and some common point. If this common point is on one of
the N wires, the measurement may be made by the use of N-1 Wattmeters.
The theorem may be stated more simply, in modern language:
In a system of N conductors, N-1 meter elements will measure the power or energy taken
provided that all the potential coils have a common tie to the conductor in which there is
no current coil.
Three-phase power measurement is accomplished by measuring the three individual
phases and adding them together to obtain the total three phase value. In older analog
meters, this measurement was accomplished using up to three separate elements. Each
element combined the single-phase voltage and current to produce a torque on the meter
disk. All three elements were arranged around the disk so that the disk was subjected to
the combined torque of the three elements. As a result the disk would turn at a higher
speed and register power supplied by each of the three wires.
According to Blondell's Theorem, it was possible to reduce the number of elements under
certain conditions. For example, a three-phase, three-wire delta system could be correctly
measured with two elements (two potential coils and two current coils) if the potential coils
were connected between the three phases with one phase in common.
In a three-phase, four-wire wye system it is necessary to use three elements. Three voltage
coils are connected between the three phases and the common neutral conductor. A
current coil is required in each of the three phases.
In modern digital meters, Blondell's Theorem is still applied to obtain proper metering. The
difference in modern meters is that the digital meter measures each phase voltage and
current and calculates the single-phase power for each phase. The meter then sums the
three phase powers to a single three-phase reading.
Some digital meters calculate the individual phase power values one phase at a time. This
means the meter samples the voltage and current on one phase and calculates a power
value. Then it samples the second phase and calculates the power for the second phase.
Finally, it samples the third phase and calculates that phase power. After sampling all three
phases, the meter combines the three readings to create the equivalent three-phase
power value. Using mathematical averaging techniques, this method can derive a quite
accurate measurement of three-phase power.
More advanced meters actually sample all three phases of voltage and current
simultaneously and calculate the individual phase and three-phase power values. The
advantage of simultaneous sampling is the reduction of error introduced due to the
difference in time when the samples were taken.
1–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
C
B
Phase B
Phase C
Node "n"
Phase A
A
N
FIGURE 1–5: Figure 1.6: Three-Phase Wye Load Illustrating Kirchhoff’s Law and Blondell’s Theorem
Blondell's Theorem is a derivation that results from Kirchhoff's Law. Kirchhoff's Law states
that the sum of the currents into a node is zero. Another way of stating the same thing is
that the current into a node (connection point) must equal the current out of the node. The
law can be applied to measuring three-phase loads. Figure 1.6 shows a typical connection
of a three-phase load applied to a three-phase, four-wire service. Krichhoff's Law holds
that the sum of currents A, B, C and N must equal zero or that the sum of currents into
Node "n" must equal zero.
If we measure the currents in wires A, B and C, we then know the current in wire N by
Kirchhoff's Law and it is not necessary to measure it. This fact leads us to the conclusion of
Blondell's Theorem- that we only need to measure the power in three of the four wires if
they are connected by a common node. In the circuit of Figure 1.6 we must measure the
power flow in three wires. This will require three voltage coils and three current coils (a
three-element meter). Similar figures and conclusions could be reached for other circuit
configurations involving Delta-connected loads.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–7
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.2
Power, Energy and Demand
It is quite common to exchange power, energy and demand without differentiating
between the three. Because this practice can lead to confusion, the differences between
these three measurements will be discussed.
Power is an instantaneous reading. The power reading provided by a meter is the present
flow of watts. Power is measured immediately just like current. In many digital meters, the
power value is actually measured and calculated over a one second interval because it
takes some amount of time to calculate the RMS values of voltage and current. But this
time interval is kept small to preserve the instantaneous nature of power.
Energy is always based on some time increment; it is the integration of power over a
defined time increment. Energy is an important value because almost all electric bills are
based, in part, on the amount of energy used.
Typically, electrical energy is measured in units of kilowatt-hours (kWh). A kilowatt-hour
represents a constant load of one thousand watts (one kilowatt) for one hour. Stated
another way, if the power delivered (instantaneous watts) is measured as 1,000 watts and
the load was served for a one hour time interval then the load would have absorbed one
kilowatt-hour of energy. A different load may have a constant power requirement of 4,000
watts. If the load were served for one hour it would absorb four kWh. If the load were
served for 15 minutes it would absorb ¼ of that total or one kWh.
Figure 1.7 shows a graph of power and the resulting energy that would be transmitted as a
result of the illustrated power values. For this illustration, it is assumed that the power level
is held constant for each minute when a measurement is taken. Each bar in the graph will
represent the power load for the one-minute increment of time. In real life the power value
moves almost constantly.
The data from Figure 1.7 is reproduced in Table 2 to illustrate the calculation of energy.
Since the time increment of the measurement is one minute and since we specified that
the load is constant over that minute, we can convert the power reading to an equivalent
consumed energy reading by multiplying the power reading times 1/60 (converting the
time base from minutes to hours).
1–8
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
80
70
kilowatts
60
50
40
30
20
10
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Time (minutes)
FIGURE 1–6: Figure 1.7: Power Use over Time
Table 1–2: Power and Energy Relationship over Time
Time Interval
(minute)
Power (kW)
Energy (kWh)
Accumulated
Energy (kWh)
1
30
0.50
0.50
2
50
0.83
1.33
3
40
0.67
2.00
4
55
0.92
2.92
5
60
1.00
3.92
6
60
1.00
4.92
7
70
1.17
6.09
8
70
1.17
7.26
9
60
1.00
8.26
10
70
1.17
9.43
11
80
1.33
10.76
12
50
0.83
12.42
13
50
0.83
12.42
14
70
1.17
13.59
15
80
1.33
14.92
As in Table 1.2, the accumulated energy for the power load profile of Figure 1.7 is 14.92
kWh.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–9
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
Demand is also a time-based value. The demand is the average rate of energy use over
time. The actual label for demand is kilowatt-hours/hour but this is normally reduced to
kilowatts. This makes it easy to confuse demand with power, but demand is not an
instantaneous value. To calculate demand it is necessary to accumulate the energy
readings (as illustrated in Figure 1.7) and adjust the energy reading to an hourly value that
constitutes the demand.
In the example, the accumulated energy is 14.92 kWh. But this measurement was made
over a 15-minute interval. To convert the reading to a demand value, it must be
normalized to a 60-minute interval. If the pattern were repeated for an additional three 15minute intervals the total energy would be four times the measured value or 59.68 kWh.
The same process is applied to calculate the 15-minute demand value. The demand value
associated with the example load is 59.68 kWh/hr or 59.68 kWd. Note that the peak
instantaneous value of power is 80 kW,, significantly more than the demand value.
Figure 1.8 shows another example of energy and demand. In this case, each bar
represents the energy consumed in a 15-minute interval. The energy use in each interval
typically falls between 50 and 70 kWh. However, during two intervals the energy rises
sharply and peaks at 100 kWh in interval number 7. This peak of usage will result in setting
a high demand reading. For each interval shown the demand value would be four times
the indicated energy reading. So interval 1 would have an associated demand of 240 kWh/
hr. Interval 7 will have a demand value of 400 kWh/hr. In the data shown, this is the peak
demand value and would be the number that would set the demand charge on the utility
bill.
100
kilowatt-hours
80
60
40
20
0
1
2
3
4
5
6
Intervals (15 mins.)
7
8
FIGURE 1–7: Figure 1.8: Energy Use and Demand
As can be seen from this example, it is important to recognize the relationships between
power, energy and demand in order to control loads effectively or to monitor use correctly.
1–10
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.3
Reactive Energy and Power Factor
The real power and energy measurements discussed in the previous section relate to the
quantities that are most used in electrical systems. But it is often not sufficient to only
measure real power and energy. Reactive power is a critical component of the total power
picture because almost all real-life applications have an impact on reactive power.
Reactive power and power factor concepts relate to both load and generation
applications. However, this discussion will be limited to analysis of reactive power and
power factor as they relate to loads. To simplify the discussion, generation will not be
considered.
Real power (and energy) is the component of power that is the combination of the voltage
and the value of corresponding current that is directly in phase with the voltage. However,
in actual practice the total current is almost never in phase with the voltage. Since the
current is not in phase with the voltage, it is necessary to consider both the inphase
component and the component that is at quadrature (angularly rotated 90o or
perpendicular) to the voltage. Figure 1.9 shows a single-phase voltage and current and
breaks the current into its in-phase and quadrature components.
IR
V
θ
IX
I
FIGURE 1–8: Figure 1.9: Voltage and Complex Current
The voltage (V) and the total current (I) can be combined to calculate the apparent power
or VA. The voltage and the in-phase current (IR) are combined to produce the real power or
watts. The voltage and the quadrature current (IX) are combined to calculate the reactive
power.
The quadrature current may be lagging the voltage (as shown in Figure 1.9) or it may lead
the voltage. When the quadrature current lags the voltage the load is requiring both real
power (watts) and reactive power (VARs). When the quadrature current leads the voltage
the load is requiring real power (watts) but is delivering reactive power (VARs) back into the
system; that is VARs are flowing in the opposite direction of the real power flow.
Reactive power (VARs) is required in all power systems. Any equipment that uses
magnetization to operate requires VARs. Usually the magnitude of VARs is relatively low
compared to the real power quantities. Utilities have an interest in maintaining VAR
requirements at the customer to a low value in order to maximize the return on plant
invested to deliver energy. When lines are carrying VARs, they cannot carry as many watts.
So keeping the VAR content low allows a line to carry its full capacity of watts. In order to
encourage customers to keep VAR requirements low, some utilities impose a penalty if the
VAR content of the load rises above a specified value.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–11
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
A common method of measuring reactive power requirements is power factor. Power
factor can be defined in two different ways. The more common method of calculating
power factor is the ratio of the real power to the apparent power. This relationship is
expressed in the following formula:
Total PF = real power / apparent power = watts/VA
This formula calculates a power factor quantity known as Total Power Factor. It is called
Total PF because it is based on the ratios of the power delivered. The delivered power
quantities will include the impacts of any existing harmonic content. If the voltage or
current includes high levels of harmonic distortion the power values will be affected. By
calculating power factor from the power values, the power factor will include the impact of
harmonic distortion. In many cases this is the preferred method of calculation because the
entire impact of the actual voltage and current are included.
A second type of power factor is Displacement Power Factor. Displacement PF is based on
the angular relationship between the voltage and current. Displacement power factor
does not consider the magnitudes of voltage, current or power. It is solely based on the
phase angle differences. As a result, it does not include the impact of harmonic distortion.
Displacement power factor is calculated using the following equation:
Displacement PF = cos θ
where θ is the angle between the voltage and the current (see Fig. 1.9).
In applications where the voltage and current are not distorted, the Total Power Factor will
equal the Displacement Power Factor. But if harmonic distortion is present, the two power
factors will not be equal.
1–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.4
Harmonic Distortion
Harmonic distortion is primarily the result of high concentrations of non-linear loads.
Devices such as computer power supplies, variable speed drives and fluorescent light
ballasts make current demands that do not match the sinusoidal waveform of AC
electricity. As a result, the current waveform feeding these loads is periodic but not
sinusoidal. Figure 1.10 shows a normal, sinusoidal current waveform. This example has no
distortion.
Current (amps)
1000
500
0
t
a
2a
–500
–1000
FIGURE 1–9: Figure 1.10: Non-distorted Current Waveform
Figure 1.11 shows a current waveform with a slight amount of harmonic distortion. The
waveform is still periodic and is fluctuating at the normal 60 Hz frequency. However, the
waveform is not a smooth sinusoidal form as seen in Figure 1.10.
1500
Current (amps)
1000
500
0
a
t
2a
–500
–1000
–1500
FIGURE 1–10: Figure 1.11: Distorted Current Wave
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–13
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
The distortion observed in Figure 1.11 can be modeled as the sum of several sinusoidal
waveforms of frequencies that are multiples of the fundamental 60 Hz frequency. This
modeling is performed by mathematically disassembling the distorted waveform into a
collection of higher frequency waveforms.
These higher frequency waveforms are referred to as harmonics. Figure 1.12 shows the
content of the harmonic frequencies that make up the distortion portion of the waveform
in Figure 1.11.
250
200
Current (amps)
150
100
50
t
0
a
-50
-100
-150
-200
-250
FIGURE 1–11: Figure 1.12: Waveforms of the Harmonics
The waveforms shown in Figure 1.12 are not smoothed but do provide an indication of the
impact of combining multiple harmonic frequencies together.
When harmonics are present it is important to remember that these quantities are
operating at higher frequencies. Therefore, they do not always respond in the same
manner as 60 Hz values.
Inductive and capacitive impedance are present in all power systems. We are accustomed
to thinking about these impedances as they perform at 60 Hz. However, these impedances
are subject to frequency variation.
XL = jωL and
XC = 1/jωC
At 60 Hz, ω = 377; but at 300 Hz (5th harmonic) ω = 1,885. As frequency changes
impedance changes and system impedance characteristics that are normal at 60 Hz may
behave entirely differently in the presence of higher order harmonic waveforms.
Traditionally, the most common harmonics have been the low order, odd frequencies, such
as the 3rd, 5th, 7th, and 9th. However newer, new-linear loads are introducing significant
quantities of higher order harmonics.
Since much voltage monitoring and almost all current monitoring is performed using
instrument transformers, the higher order harmonics are often not visible. Instrument
transformers are designed to pass 60 Hz quantities with high accuracy. These devices,
when designed for accuracy at low frequency, do not pass high frequencies with high
1–14
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
accuracy; at frequencies above about 1200 Hz they pass almost no information. So when
instrument transformers are used, they effectively filter out higher frequency harmonic
distortion making it impossible to see.
However, when monitors can be connected directly to the measured circuit (such as direct
connection to a 480 volt bus) the user may often see higher order harmonic distortion. An
important rule in any harmonics study is to evaluate the type of equipment and
connections before drawing a conclusion. Not being able to see harmonic distortion is not
the same as not having harmonic distortion.
It is common in advanced meters to perform a function commonly referred to as
waveform capture. Waveform capture is the ability of a meter to capture a present picture
of the voltage or current waveform for viewing and harmonic analysis. Typically a
waveform capture will be one or two cycles in duration and can be viewed as the actual
waveform, as a spectral view of the harmonic content, or a tabular view showing the
magnitude and phase shift of each harmonic value. Data collected with waveform
capture is typically not saved to memory. Waveform capture is a real-time data collection
event.
Waveform capture should not be confused with waveform recording that is used to record
multiple cycles of all voltage and current waveforms in response to a transient condition.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1–15
CHAPTER 1: THREE-PHASE POWER MEASUREMENT
1.5
Power Quality
Power quality can mean several different things. The terms "power quality" and "power
quality problem" have been applied to all types of conditions. A simple definition of "power
quality problem" is any voltage, current or frequency deviation that results in misoperation or failure of customer equipment or systems. The causes of power quality
problems vary widely and may originate in the customer equipment, in an adjacent
customer facility or with the utility.
In his book Power Quality Primer, Barry Kennedy provided information on different types of
power quality problems. Some of that information is summarized in Table 1.3.
Table 1–3: Typical Power Quality Problems and Sources
Cause
Disturbance Type
Source
Impulse transient
Transient voltage disturbance,
sub-cycle duration
Lightning
Electrostatic discharge
Load switching
Capacitor switching
Oscillatory
transient with decay
Transient voltage, sub-cycle duration
Line/cable switching
Capacitor switching
Load switching
Sag/swell
RMS voltage, multiple cycle duration
Remote system faults
Interruptions
RMS voltage, multiple
seconds or longer duration
System protection
Circuit breakers
Fuses
Maintenance
Under voltage/over voltage
RMS voltage, steady state, multiple
seconds or longer
duration
Motor starting
Load variations
Load dropping
Voltage flicker
RMS voltage, steady state, repetitive
condition
Intermittent loads
Motor starting
Arc furnaces
Harmonic distortion
Steady state current or voltage, long-term
duration
Non-linear loads
System resonance
It is often assumed that power quality problems originate with the utility. While it is true
that may power quality problems can originate with the utility system, many problems
originate with customer equipment. Customer-caused problems may manifest themselves
inside the customer location or they may be transported by the utility system to another
adjacent customer. Often, equipment that is sensitive to power quality problems may in
fact also be the cause of the problem.
If a power quality problem is suspected, it is generally wise to consult a power quality
professional for assistance in defining the cause and possible solutions to the problem.
1–16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 2: Meter Overview and
Specifications
Meter Overview and Specifications
2.1
Multilin™ EPM7000 Meter Overview
The EPM7000 meter is a multifunction, data logging, power and energy meter with
waveform recording capability, designed to be used in electrical substations, panel boards,
as a power meter for OEM equipment, and as a primary revenue meter, due to its high
performance measurement capability. The unit provides multifunction measurement of all
electrical parameters and makes the data available in multiple formats via display,
communication systems, and analog retransmits. The unit also has data logging and load
profiling to provide historical data analysis, and waveform recording that allows for
enhanced power quality analysis.
The EPM7000 meter offers up to 4 MegaBytes of flash memory. The unit provides you with
up to seven logs: three historic logs, a log of limit alarms, a log of I/O changes, a waveform
log, and a sequence of events log. (See NOTE on flash memory on page 2-6.)
The purposes of these features include historical load profiling, voltage analysis, and
recording power factor distribution. The EPM7000 meter’s real-time clock allows all events
to be time-stamped.
Optional 100BaseT Ethernet capability is available for the meter. When it is equipped with
an Ethernet card, the meter’s real-time clock can be synchronized with an
outside Network Time Protocol (NTP) server (see the GE Communicator EXT USer Manual for
instructions on using this feature.) A EPM7000 meter with an Ethernet card also becomes a
Web server. See Chapter 8 for more information on this feature.
The EPM7000 meter is designed with advanced measurement capabilities, allowing it to
achieve high performance accuracy. It is specified as a 0.2% class energy meter for billing
applications as well as a highly accurate panel indication meter.
The EPM7000 meter provides additional capabilities, including standard RS485, Modbus
and DNP 3.0 Protocols, an IrDA Port for remote interrogation, and Option cards that can be
added at any time.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–1
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
Features of the EPM7000 meter include:
Note CT/PT Compensation (V-Switch™ keys 3-6: see Chapter 5 in the GE Communicator EXT User Manual for instructions on using
this feature*).
2.1.1
•
0.2% Class revenue certifiable Energy and Demand metering
•
Meets ANSI C12.20 (0.2%) and IEC 687 (0.2%) classes
•
Multifunction measurement including Voltage, current, power, frequency, energy, etc.
•
Optional secondary voltage display (see Chapter 5 in the GE Communicator EXT User
Manual for instructions on setting up this feature*)
•
Power quality measurements (%THD and Alarm Limits) - for meters with
Software Options C to F, symmetrical components, voltage unbalance, and current
unbalance are also available and can be used with the Limits functionality (see
Chapter 5 in the GE Communicator EXT User Manual for instructions on using this
feature*)
•
Software Options - field upgradable without removing installed meter
•
Percentage of Load Bar for analog meter reading
•
Easy to use faceplate programming
•
IrDA Port for laptop PC remote read
•
RS485 communication
•
Optional I/O Cards - field upgradable without removing installed meter, including
100BaseT Ethernet.
•
Sampling rate of up to 512 samples per cycle for waveform recording
•
Transformer/Line Loss compensation (see Chapter 5 and Appendix B in the GE
Communicator EXT User Manual for instructions on using this feature*).
Access the GE Communicator EXT User Manual from the GE Communicator EXT CD or by
clicking Help>Contents from the GE Communicator EXT Main screen.
Voltage and Current Inputs
Universal Voltage Inputs
Voltage Inputs allow measurement up to Nominal 480VAC (Phase to Reference) and
600VAC (Phase to Phase). This insures proper meter safety when wiring directly to high
voltage systems. One unit will perform to specification on 69 Volt, 120 Volt, 230 Volt, 277
Volt, and 347 Volt power systems.
Note
Higher voltages require the use of potential transformers (PTs).
Current Inputs
The unit supports a 5 Amp or a 1 Amp secondary for current measurements.
Note
The secondary current must be specified and ordered with the meter.
The EPM7000 meter’s Current Inputs use a unique dual input method:
2–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
Method 1: CT Pass Through
The CT passes directly through the meter without any physical termination on the meter.
This insures that the meter cannot be a point of failure on the CT circuit. This is preferable
for utility users when sharing relay class CTs. No Burden is added to the secondary CT
circuit.
Method 2: Current “Gills”
This unit additionally provides ultra-rugged Termination Pass Through Bars that allow CT
leads to be terminated on the meter. This, too, eliminates any possible point of failure at
the meter. This is a preferred technique for insuring that relay class CT integrity is not
compromised (the CT will not open in a fault condition).
2.1.2
Ordering Information
Table 2–1: EPM7000 Order Codes
Base Unit
Frequency
Current Input
Software
PL7000 –
*
PL7000
|
5
6
–
*
|
|
|
1A
5A
–
*
–
|
|
|
|
|
A
B
C
D
E
F
Power Supply
*
|
|
|
|
|
|
|
|
|
|
|
HI
LDC
I/O Modules
–
*
*
|
|
|
|
|
|
|
|
|
|
|
|
|
X
E1
C1
C20
RS1
PS1
F1
F2
|
|
|
|
|
|
|
|
|
|
|
|
|
X
E1
C1
C20
RS1
PS1
F1
F2
EPM7000 Power Quality Meter
50 Hz AC frequency system
60 Hz AC frequency system
2 A secondary
10 A secondary
Multimeter function only
Data Logging memory
Power Quality Harmonics
Limits and Control
64 samples/cycle Waveform Recording
512 samples/cycle Waveform Recording
90 to 265 VAC; 100 to 370 VDC
18 to 60 VDC
None
100BaseT Ethernet (see Note below)
Four Channel Bi-directional 0 to 1 mA Outputs
Four Channel Bi-directional 0 to 20 mA Outputs
Two Relay Status Outputs / Two Status Inputs
Four Pulse Outputs / Four Status Inputs
Fiber Optic Interface with ST Terminations
Fiber Optic Interface with Versatile Terminations
Maximum one E1 module per EPM7000
Note
2.1.3
Software Options (see above)
The EPM7000 meter is equipped with a variety of software options, firmware that allows
you to enable meter features through software communication. These options allow the
unit to be upgraded after installation without removing it from service.
Available Software Options:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–3
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
• Software Option A: Multifunction measurement.
• Software Option B: Multifunction measurement and 2 MegaBytes for data-logging.
• Software Option C: Multifunction measurement with harmonics and 2 MegaBytes
for data-logging.
• Software Option D: Multifunction measurement with harmonics, 2 MegaBytes for
data-logging, and limit and control functions.
• Software Option E: Multifunction measurement with harmonics, 3 MegaBytes for
data-logging, limit and control functions, and 64 samples per cycle waveform
recorder.
• Software Option F: Multifunction measurement with harmonics, 4 MegaBytes for
data-logging, limit and control functions, and 512 samples per cycle waveform
recorder.
Because the memory is flash-based rather than NVRAM (non-volatile random-access
memory), some sectors are reserved for overhead, erase procedures, and spare sectors for
long-term wear reduction.
Note
Obtaining Software Option:
Contact GE Multilin and provide the following information:
1.
Serial Number or Numbers of the meters you are upgrading. Use the
number(s), with leading zeros, shown in the GE Communicator EXT Device
Status screen (from the GE Communicator EXT Main screen, click
Tools>Device Status).
2.
Desired Software Option.
3.
Credit Card or Purchase Order Number.
GE Multilin will issue you the Software Option.
Enabling the Software Option:
1.
Open GE Communicator EXT.
2.
Power up your meter.
3.
Connect to the EPM7000 meter through GE Communicator EXTC
4.
Click Tools>Change Software Option from the Title Bar. A screen opens,
requesting the encrypted key. Enter the Software Option key provided by GE
Multilin.
5.
Click the OK button.
The Software Option is enabled and the meter is reset.
For more details on software configuration, refer to the GE Communicator EXT User’s
Manual.
Note
2.1.4
Measured Values
The EPM7000 meter provides the following Measured Values all in Real-Time
Instantaneous, and some additionally as Average, Maximum and Minimum values.
2–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
Table 2–2: EPM7000 Meter’s Measured Values
Measured Values
2.1.5
Instantaneous
Avg
Max
Min
Voltage L-N
X
X
X
Voltage L-L
X
X
X
Current per Phase
X
X
X
X
Current Neutral
X
X
X
X
WATT(A,B,C,Tot.)
X
X
X
X
VAR (A,B,C,Tot.)
X
X
X
X
VA (A,B,C,Tot.)
X
X
X
X
PF (A,B,C,Tot.)
X
X
X
X
+Watt-Hour (A,B,C,Tot.)
X
-Watt-Hour (A,B,C,Tot.)
X
Watt-Hour Net
X
+VAR-Hour (A,B,C,Tot.)
X
-VAR-Hour (A,B,C,Tot.)
X
VAR-Hour Net (A,B,C,Tot.)
X
VA-Hour (A,B,C,Tot.)
X
Frequency
X
X
X
Harmonics to the 40th Order
X
%THD
X
X
X
Voltage Angles
X
Current Angles
X
% of Load Bar
X
Waveform Scope
X
Utility Peak Demand
The EPM7000 meter provides user-configured Block (Fixed) Window or Rolling Window
Demand modes. This feature enables you to set up a customized Demand profile. Block
Window Demand mode records the average demand for time intervals that you define
(usually 5, 15 or 30 minutes). Rolling Window Demand mode functions like multiple,
overlapping Block Window Demands. You define the subintervals at which an average of
demand is calculated. An example of Rolling Window Demand mode would be a 15minute Demand block using 5-minute subintervals, thus providing a new demand reading
every 5 minutes, based on the last 15 minutes.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–5
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
Utility Demand Features can be used to calculate Watt, VAR, VA and PF readings. Voltage
provides an Instantaneous Max and Min reading which displays the highest surge and
lowest sag seen by the meter. All other parameters offer Max and Min
capability over the user-selectable averaging period.
2–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
2.2
Specifications
POWER SUPPLY
Range:..................................................................HI Option: Universal, 90 to 265 VAC @50/60Hz; 100 to 370
VDC
................................................................................LDC Option: 18 to 60 VDC
Power Consumption: ....................................5 to 10 VA, 3.5 to 7 W - depending on the meter’s
hardware configuration
VOLTAGE INPUTS
(For Accuracy Specifications, see Section 2.4.)
Absolute Maximum Range: .......................Universal, Auto-ranging:
................................................................................Phase to Reference Va, Vb, Vc to Vref: 20 to 576 VAC
................................................................................Phase to Phase Va to Vb, Vb to Vc, Vc to Va: 0 to 721VAC
Supported hookups: .....................................3 Element Wye, 2.5 Element Wye, 2 Element Delta, 4 Wire
Delta
Input Impedance:...........................................1M Ohm/Phase
Burden: ...............................................................0.36VA/Phase Max at 600 Volts;
0.014VA at 120 Volts
Pickup Voltage:................................................20VAC
Connection:.......................................................7 Pin 0.400” Pluggable Terminal Block
AWG#12 -26/ (0.129 -3.31) mm2
Fault Withstand: .............................................Meets IEEE C37.90.1
Reading:..............................................................Programmable Full Scale to any PT Ratio
CURRENT INPUTS
(For Accuracy Specifications, see Section 2.4.)
Class 10: ............................................................5A Nominal, 10A Maximum
Class 2: ...............................................................1A Nominal, 2A Maximum
Burden:................................................................0.005VA Per Phase Max at 11 Amps
Pickup Current: ................................................0.1% of nominal (0.2% of nominal if using Current Only
mode, that is, there is no connection to the voltage
inputs.)
Connections: ....................................................O Lug or U Lug Electrical Connection (Figure 4.1)
................................................................................Pass-through Wire, 0.177” / 4.5mm maximum diameter
................................................................................Quick Connect, 0.25” Male Tab
Fault Withstand (at 23o C): ........................100A/10sec., 300A/3sec.
................................................................................500A/1sec.
Reading:..............................................................Programmable Full Scale to any CT Ratio
Continuous Current Withstand:...............20 Amps for Screw Terminated or Pass Through
Connections
KYZ/RS485 PORT SPECIFICATIONS
RS485 Transceiver; meets or exceeds EIA/TIA-485 Standard:
Type: .....................................................................Two-wire, half duplex
Min. Input Impedance: .................................96 kΩ
Max. Output Current: ....................................±60 mA
WH PULSE
KYZ output contacts (and infrared LED light pulses through face plate):
(See Section 6.4 for Kh values.)
Pulse Width: ......................................................90ms
Full Scale Frequency:....................................~3Hz
Contact type:....................................................Solid State – SPDT (NO – C – NC)
Relay type: .........................................................Solid state
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–7
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
Peak switching voltage:...............................DC ±350V
Continuous load current: ............................120mA
Peak load current:..........................................350mA for 10ms
On resistance, max.:......................................35Ω
Leakage current:.............................................1µ[email protected]
Isolation: .............................................................AC 3750V
Reset State: .......................................................(NC - C) Closed; (NO - C) Open
Infrared LED:
Peak Spectral Wavelength:........................940nm
Reset State: .......................................................Off
FIGURE 2–1: Internal Schematic
2–8
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
FIGURE 2–2: Output timing
ISOLATION
All Inputs and Outputs are galvanically isolated to 2500 VAC
ENVIRONMENTAL RATING
Storage:...............................................................-20 to +700 C
Operating:..........................................................-20 to +700 C
Humidity:............................................................to 95% RH Non-condensing
Faceplate Rating: ...........................................NEMA12 (Water Resistant), Mounting Gasket Included
Measurement Methods
Voltage, Current:.............................................True RMS
Power:..................................................................Sampling at over 400 Samples per Cycle on All Channels
Update Rate
Watts, VAR and VA: ........................................Every 6 cycles (e.g., 100ms @ 60 Hz)
All other parameters:....................................Every 60 cycles (e.g., 1 s @ 60 Hz)
1 second for current only measurement, if reference
voltage is not available
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–9
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
COMMUNICATION
Standard:............................................................RS485 Port through Back Plate
IrDA Port through Face Plate
Energy Pulse Output through Back Plate and Infrared LED
through Faceplate
Optional, through I/O Card Slot 1: ..........100BaseT Ethernet Card
Four Channel Bi-directional 0 to 1 ma Outputs
Four Channel Bi-directional 0 to 20 ma Outputs
Two Relay Status Outputs/Two Status Inputs
Four Pulse Outputs/Two Status Inputs
Fiber Optic Interface ST Terminated Card
Fiber Optic Interface Versatile Link Terminated Card
Protocols: ..........................................................Modbus RTU, Modbus ASCII, DNP 3.0
Com Port Baud Rate: ....................................9,600 to 57,600 bps
Com Port Address: ........................................001 to 247
Data Format: ....................................................8 Bit, No Parity
EPM7000T transducer..................................Default Initial Communication Baud 9600 (See Chapter 5)
MECHANICAL PARAMETERS
Dimensions: .....................................................see Chapter 3.
Weight (without Option card): ..................2 pounds/ 0.9kg (ships in a 6”/152.4mm cube container)
2.2.1
Compliance
Test
2–10
Reference Standard
Level/Class
Electrostatic Discharge
EN/IEC61000-4-2
Level 3
RF Immunity
EN/IEC61000-4-3
10 V/min
Fast Transient Disturbance
EN/IEC61000-4-4
Level 3
Surge Immunity
EN/IEC61000-4-5
Level 3
Conducted RF Immunity
EN/IEC61000-4-6
Level 3
Radiated and Conductive Emissions
EN/IEC61000-6-4
CISPR 11
Class A
Voltage Dip & Interrruption
EN/IEC61000-4-11
0, 40, 70, 100%
dips, 250/300 cycle
interrupts
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
APPROVALS
Applicable Council Directive
According to:
Low Voltage Directive
EN61010-1
CE Compliance
EMC Directive
EN61326-1
EN61000-6-4
EN61000-6-2
North America
cULus Listed
ISO
Manufactured under a registered
quality program
UL61010-1 (PICQ)
C22.2. No 61010-1 (PICQ7)
ISO9001
ACCURACY
(For full Range specifications see Section 2.2.)
EPM7000 Clock Accuracy:
Max. +/-2 seconds per day at 25oC.
For 23o C, 3 Phase balanced Wye or Delta load, at 50 or 60 Hz (as per order), 5A (Class 10)
nominal unit:
Parameter
Accuracy
Accuracy Input Range1
Voltage L-N [V]
0.1% of reading
(69 to 480)V
Voltage L-L [V]
0.2% of reading 2
(120 to 600)V
Current Phase [A]
0.1% of reading 1, 3
(0.15 to 5) A
1
(0.15 to 5) A @ (45 to 65) Hz
Current Neutral (calculated) [A]
2% of Full Scale
Active Power Total [W]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0.5
to 1) lag/lead PF
Active Energy Total [Wh]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0.5
to 1) lag/lead PF
Reactive Power Total [VAR]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0
to 0.8) lag/lead PF
Reactive Energy Total [VARh]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0
to 0.8) lag/lead PF
Apparent Power Total [VA]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0.5
to 1) lag/lead PF
Apparent Energy Total [VAh]
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0.5
to 1) lag/lead PF
Power Factor
0.2% of reading 1, 2
(0.15 to 5) A @ (69 to 480) V @ +/- (0.5
to 1) lag/lead PF
Frequency [Hz]
+/- 0.03 Hz
(45 to 65) Hz
Total Harmonic Distortion [%]
+/- 2% 1, 4
(0.5 to 10)A or (69 to 480)V,
measurement range (1 to 99.99)%
Load Bar
+/- 1 segment
(0.005 to 6) A
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
2–11
CHAPTER 2: METER OVERVIEW AND SPECIFICATIONS
1: For 2.5 element programmed units, degrade accuracy by an additional 0.5% of reading.
For 1A (Class 2) Nominal, degrade accuracy by an additional 0.5% of reading.
For 1A (Class 2) Nominal, the input current range for accuracy specification is 20% of the values
listed in the table.
2: For unbalanced voltage inputs where at least one crosses the 150V auto-scale threshold (for
example, 120V/120V/208V system), degrade the accuracy to 0.4% of reading.
3: With reference voltage applied (VA, VB, or VC). Otherwise, degrade accuracy to 0.2%. See hookup
diagrams 8, 9, and 10 in Chapter 4.
4: At least one voltage input (minimum 20 Vac) must be connected for THD measurement on
current channels.
2–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 3: Mechanical Installation
Mechanical Installation
3.1
Introduction
The EPM7000 meter can be installed using a standard ANSI C39.1 (4” Round) or an IEC
92mm DIN (Square) form. In new installations, simply use existing DIN or ANSI
punches. For existing panels, pull out old analog meters and replace them with the
EPM7000 meter. The various models use the same installation. See Section 3.4 for
EPM7000T transducer installation. See Chapter 4 for wiring diagrams.
Note
The drawings shown below and on the next page give you the meter dimensions in
inches and centimeters [cm shown in brackets] Tolerance is +/- 0.1” [.25 cm].
FIGURE 3–1: Meter Front and Side Dimensions
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
3–1
CHAPTER 3: MECHANICAL INSTALLATION
FIGURE 3–2: Meter Back Dimensions
FIGURE 3–3: ANSI and DIN Cutout Dimensions
Recommended Tools for EPM7000 Meter Installation:
• #2 Phillips screwdriver
• Small adjustable wrench
• Wire cutters
The EPM7000 meter is designed to withstand harsh environmental conditions;
however it is recommended you install it in a dry location, free from dirt and corrosive
substances. (See Environmental Specifications in Chapter 2.)
3–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 3: MECHANICAL INSTALLATION
3.2
ANSI Installation Steps
1.
Insert 4 threaded rods by hand into the back of meter. Twist until secure.
2.
Slide NEMA 12 Mounting Gasket onto back of meter with rods in place.
3.
Slide meter with Mounting Gasket into panel.
4.
Secure from back of panel with lock washer and nut on each threaded rod.
Use a small wrench to tighten. Do not overtighten. The maximum installation
torque is 0.4 Newton-Meter.
NEMA12 Mounting Gasket
Threaded Rods (4)
Lock Washers and Nuts (4 sets)
FIGURE 3–4: ANSI Installation
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
3–3
CHAPTER 3: MECHANICAL INSTALLATION
3.3
DIN Installation Steps
1.
Slide meter with NEMA 12 Mounting Gasket into panel. (Remove ANSI Studs, if
in place.)
2.
From back of panel, slide 2 DIN Mounting Brackets into grooves in top and
bottom of meter housing. Snap into place.
3.
Secure meter to panel with lock washer and a #8 screw through each of the 2
mounting brackets. Tighten with a #2 Phillips screwdriver. Do not overtighten.
The maximum installation torque is 0.4 Newton-Meter
DIN Mounting Bracket
#8 Screw
Top Mounting
Bracket Groove
Bottom Mounting
Bracket Groove
Meter with NEMA 12
Mounting Bracket
Remove (unscrew) ANSI Studs
FIGURE 3–5: DIN Installation
3–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 4: Electrical Installation
Electrical Installation
4.1
Considerations When Installing Meters
Installation of the EPM7000 meter must be performed by only qualified personnel
who follow standard safety precautions during all procedures. Those personnel
should have appropriate training and experience with high voltage devices.
Appropriate safety gloves, safety glasses and protective clothing is recommended.
During normal operation of the EPM7000 meter, dangerous voltages flow through
many parts of the meter, including: Terminals and any connected CTs (Current
Transformers) and PTs (Potential Transformers), all I/O Modules (Inputs and Outputs)
and their circuits. All Primary and Secondary circuits can, at times, produce lethal
voltages and currents. Avoid contact with any current-carrying surfaces.
Do not use the meter or any I/O Output Device for primary protection or in an energylimiting capacity. The meter can only be used as secondary protection. Do not use the
meter for applications where failure of the meter may cause harm or death. Do not
use the meter for any application where there may be a risk of fire.
All meter terminals should be inaccessible after installation.
Do not apply more than the maximum voltage the meter or any attached device can
withstand. Refer to meter and/or device labels and to the Specifications for all devices
before applying voltages. Do not HIPOT/Dielectric test any Outputs, Inputs or
Communications terminals.
GE Multilin recommends the use of Shorting Blocks and Fuses for voltage leads and
power supply to prevent hazardous voltage conditions or damage to CTs, if the meter
needs to be removed from service. CT grounding is optional.
Note
•
If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
•
There is no required preventive maintenance or inspection necessary for safety.
however, any repair or maintenance should be performed by the factory.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–1
CHAPTER 4: ELECTRICAL INSTALLATION
Note
4–2
DISCONNECT DEVICE: The following part is considered the equipment disconnect
device: A switch or circuit-breaker shall be included in the end-use equipment or
building installation. the switch shall be in close proximity to the equipment and
within easy reach of the operator. the switch shall be marked as the disconnecting
device for the equipment.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
4.2
CT Leads Terminated to Meter
The EPM7000 meter is designed to have Current Inputs wired in one of three ways.
Diagram 4.1 shows the most typical connection where CT Leads are terminated to the
meter at the Current Gills. This connection uses Nickel-Plated Brass Studs (Current
Gills) with screws at each end. This connection allows the CT wires to be terminated
using either an “O” or a “U” lug. Tighten the screws with a #2 Phillips screwdriver. The
maximum installation torque is 1 Newton-Meter.
Other current connections are shown in Figures 4.2 and 4.3. Voltage and RS485/KYZ
Connection is shown in Figure 4.4.
FIGURE 4–1: CT Leads terminated to Meter, #8 Screw for Lug Connection
Wiring Diagrams are shown in section 4.8 of this chapter.
Communications Connections are detailed in Chapter 5.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–3
CHAPTER 4: ELECTRICAL INSTALLATION
4.3
CT Leads Pass Through (No Meter Termination)
The second method allows the CT wires to pass through the CT Inputs without
terminating at the meter. In this case, remove the Current Gills and place the CT wire
directly through the CT opening. The opening accommodates up to 0.177” / 4.5mm
maximum diameter CT wire.
CT wire passing through meter
Current Gills
removed
FIGURE 4–2: Pass-through Wire Electrical Connection
4–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
4.4
Quick Connect Crimp-on Terminations
For quick termination or for portable applications, 0.25” Quick Connect Crimp-on
Connectors can also be used
Quick Connect Crimp-on
Terminations
FIGURE 4–3: Quick Connect Electrical Connection
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–5
CHAPTER 4: ELECTRICAL INSTALLATION
4.5
Voltage and Power Supply Connections
Voltage Inputs are connected to the back of the unit via a optional wire connectors.
The connectors accommodate AWG# 12 -26/ (0.129 - 3.31)mm2.
RS485 and KYZ
Pulse Outputs
3 Power
Supply
Inputs
CAUTION! Do
NOT apply
Input or
Supply
voltage to
these
terminals.
4
Voltage
Inputs
FIGURE 4–4: Meter Connection
4–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
4.6
Ground Connections
The meter’s Ground Terminals should be connected directly to the installation’s
protective earth ground. Use AWG# 12/2.5 mm2 wire for this connection.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–7
CHAPTER 4: ELECTRICAL INSTALLATION
4.7
Voltage Fuses
GE Multilin recommends the use of fuses on each of the sense voltages and on the control
power, even though the wiring diagrams in this chapter do not show them.
4–8
•
Use a 0.1 Amp fuse on each voltage input.
•
Use a 3 Amp Slow Blow fuse on the power supply.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
4.8
Electrical Connection Diagrams
The following pages contain electrical connection diagrams for the EPM7000 meter.
Choose the diagram that best suits your application. Be sure to maintain the CT polarity
when wiring.
The diagrams are presented in the following order:
1.
Three Phase, Four-Wire System Wye/Delta with Direct Voltage, 3 Element
•
(1a) Example of Dual-Phase Hookup
•
(1b) Example of Single Phase Hookup
2.
Three Phase, Four-Wire System Wye with Direct Voltage, 2.5 Element
3.
Three-Phase, Four-Wire Wye/Delta with PTs, 3 Element
4.
Three-Phase, Four-Wire Wye with PTs, 2.5 Element
5.
Three-Phase, Three-Wire Delta with Direct Voltage
6.
Three-Phase, Three-Wire Delta with 2 PTs
7.
Three-Phase, Three-Wire Delta with 3 PTs
8.
Current Only Measurement (Three Phase)
9.
Current Only Measurement (Dual Phase)
10. Current Only Measurement (Single Phase)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–9
CHAPTER 4: ELECTRICAL INSTALLATION
1. Service: WYE/Delta, 4-Wire with No PTs, 3 CTs
Select: “3 EL WYE” (3 Element Wye) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
C
C
A
B
4–10
A
B
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
1a. Example of Dual Phase Hookup
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–11
CHAPTER 4: ELECTRICAL INSTALLATION
(1b) Example of Single Phase Hookup
4–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
2. Service: 2.5 Element WYE, 4-Wire with No PTs, 3 CTs
Select: “2.5 EL WYE” (2.5 Element Wye) from the EPM7000 meter’s Front Panel
Display. (See Chapter 6.)
C
A
B
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–13
CHAPTER 4: ELECTRICAL INSTALLATION
3. Service: WYE/Delta, 4-Wire with 3 PTs, 3 CTs
Select: “3 EL WYE” (3 Element Wye) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
C
C
A
B
4–14
A
B
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
4. Service: 2.5 Element WYE, 4-Wire with 2 PTs, 3 CTs
Select: “2.5 EL WYE” (2.5 Element Wye) from the EPM7000 meter’s Front Panel
Display. (See Chapter 6.)
C
A
B
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–15
CHAPTER 4: ELECTRICAL INSTALLATION
5. Service: Delta, 3-Wire with No PTs, 2 CTs
Select: “2 CT DEL” (2 CT Delta) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.
C
C
B
A B
A
Not connected to meter
4–16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
6. Service: Delta, 3-Wire with 2 PTs, 2 CTs
Select: “2 CT DEL” (2 CT Delta) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.).
C
C
B
A B
A
Not connected to meter
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–17
CHAPTER 4: ELECTRICAL INSTALLATION
7. Service: Delta, 3-Wire with 2 PTs, 3 CTs
Select: “2 CT DEL” (2 CT Delta) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
Note
The third CT for hookup is optional, and is used only for Current measurement..
C
C
B
A B
A
Not connected to meter
4–18
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
8. Service: Current Only Measurement (Three Phase)
*
Select: “3 EL WYE” (3 Element Wye) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
* This connection is not required, but is recommended for improved accuracy.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–19
CHAPTER 4: ELECTRICAL INSTALLATION
9. Service: Current Only Measurement (Dual Phase)
Select: “3 EL WYE” (3 Element Wye) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
* This connection is not required, but is recommended for improved accuracy.
4–20
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 4: ELECTRICAL INSTALLATION
10. Service: Current Only Measurement (Single Phase)
*
Select: “3 EL WYE” (3 Element Wye) from the EPM7000 meter’s Front Panel Display. (See
Chapter 6.)
* This connection is not required, but is recommended for improved accuracy.
Note
The diagram shows a connection to Phase A, but you can also connect to Phase B
or Phase C.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
4–21
CHAPTER 4: ELECTRICAL INSTALLATION
4–22
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 5: Communication
Installation
Communication Installation
5.1
Multilin™ EPM7000 Meter Communication
The EPM7000 meter provides two independent Communication Ports. The first port, COM
1, is an Optical IrDA Port. The second port, COM 2, provides RS485 communication
speaking Modbus ASCII, Modbus RTU, and DNP 3.0 protocols. Additionally, the EPM7000
meter has two optional communication cards: the Fiber Optic Communication Card and
the 10/100BaseT Ethernet Communication Card. See Chapter 7 for more information on
these options.
5.1.1
IrDA Port (COM 1)
The EPM7000 meter’s COM 1 IrDA Port is on the face of the meter. The IrDA Port allows the
unit to be read and programmed without the need of a communication cable. Just point at
the meter with an IrDA-equipped laptop PC to configure it.
Note
5.1.2
•
Settings for COM 1 (IrDA Port) are configured using GE Communicator EXT software.
•
This port only communicates via Modbus ASCII Protocol.
•
Refer to Appendix D for instructions on using the USB to IrDA Adapter.
RS485 / KYZ Output (COM 2)
COM 2 provides a combination RS485 and an Energy Pulse Output (KYZ pulse).
See Chapter 2, Section 2.2 for the KYZ Output Specifications; see Chapter 6, Section 6.4 for
Pulse Constants.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–1
CHAPTER 5: COMMUNICATION INSTALLATION
RS485
KYZ
FIGURE 5–1: EPM7000 Meter Back with RS485 Communication Installation
RS485 allows you to connect one or multiple EPM7000 meters to a PC or other device, at
either a local or remote site. All RS485 connections are viable for up to 4000 feet (1219.20
meters).
FIGURE 5–2: EPM7000 Meter Connected to a PC via RS485 bus
As shown in Figure 5.2, to connect a EPM7000 meter to a PC, you need to use an RS485 to
RS232 converter.
Figure 5.3 shows the detail of a 2-wire RS485 connection.
5–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
FIGURE 5–3: 2-wire RS485 Connection
For All RS485 Connections:
Note
• Use a shielded twisted pair cable and ground the shield, preferably at one location
only.
• Establish point-to-point configurations for each device on a RS485 bus: connect (+)
terminals to (+) terminals; connect (-) terminals to (-) terminals.
• You may connect up to 31 meters on a single bus using RS485. Before assembling
the bus, each meter must have a unique address: refer to Chapter 5 of the GE
Communicator EXT 3.0 User’s Manual for instructions.
• Protect cables from sources of electrical noise.
• Avoid both “Star” and “Tee” connections (see Figure 5.5).
• No more than two cables should be connected at any one point on an RS485
network, whether the connections are for devices, converters, or terminal strips.
• Include all segments when calculating the total cable length of a network. If you
are not using an RS485 repeater, the maximum length for cable connecting all
devices is 4000 feet (1219.20 meters).
• Connect shield to RS485 Master and individual devices as shown in Figure 5.4. You
may also connect the shield to earth-ground at one point.
• Termination Resistors (RT) may be needed on both ends for longer length
transmission lines. However, since the meter has some level of termination
internally, Termination Resistors may not be needed. When they are used, the
value of the Termination Resistors is determined by the electrical parameters of
the cable.
Figure 5.4 below, shows a representation of an RS485 Daisy Chain connection.
Master device
Last Slave device N
RT
SH
+
RT
-
Slave device 1
Slave device 2
SH
SH
+
Twisted pair, shielded (SH) cable
-
Twisted pair, shielded (SH) cable
+
-
SH
+
-
Twisted pair, shielded (SH) cable
Earth Connection, preferably at
single location
FIGURE 5–4: RS485 Daisy Chain Connection
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–3
CHAPTER 5: COMMUNICATION INSTALLATION
Slave device 1
SH
+
-
Long stub results “T” connection that can cause
interference problem!
Master device
Last Slave device N
RT
RT
Slave device 2
SH +
-
SH
Twisted pair, shielded (SH) cable
+
-
SH
Twisted pair, shielded (SH) cable
+
-
Twisted pair, shielded (SH) cable
Earth Connection, preferably at
single location
Twisted pair, shielded (SH) cable
Twisted pair, shielded (SH) cable
Slave device 1
Slave device 2
SH +
-
-
Master device
SH
+
SH
+
-
+ SH
“STAR” connection can cause interference
problem!
-
SH
Slave device 3
+
Slave device 4
Twisted pair, shielded (SH) cable
Twisted pair, shielded (SH) cable
FIGURE 5–5: Incorrect “T” and “Star” Topologies
5–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
5.2
Accessing the Meter in Default Communication Mode
You can connect to the EPM7000T in Default Communication mode. This feature is useful in
debugging or if you do not know the meter's programmed settings and want to find them.
For 5 seconds after the EPM7000T is powered up, you can use the RS485 port with Default
Communication mode to poll the Name Register. You do this by connecting to the meter
with the following default settings (see Section 5.2.2 on the next page):
Baud Rate: 9600
Address: 001
Protocol: Modbus RTU
The meter continues to operate with these default settings for 5 minutes. During this time,
you can access the meter's Device Profile to ascertain/change meter information. After 5
minutes of no activity, the meter reverts to the programmed Device
Profile settings.
Note
In Normal operating mode the initial factory communication settings are:
Baud Rate: 57,600
Address: 001
Protocol: Modbus RTU
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–5
CHAPTER 5: COMMUNICATION INSTALLATION
5.3
Connecting to the Meter through GE Communicator EXT
How to Connect:
5–6
1.
Open the GE Communicator EXT software.
2.
Click the Connect icon in the Icon bar.
3.
The Connect screen opens, showing the Default settings. Make sure your
settings are the same as shown here. Use the pull-down menus to make any
necessary changes to the settings.
4.
Click the Connect button. If you have a problem connecting, you may have to
disconnect power to the meter, then reconnect power and click the Connect
button, again.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
5.
You will see the Device Status screen, confirming connection to your meter.
Click OK.
6.
Click the Profile icon in the Title Bar.
7.
You will see the EPM7000 meter’s Device Profile screen. The Menu on the left
side of the screen allows you to navigate between settings screens (see
below).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–7
CHAPTER 5: COMMUNICATION INSTALLATION
Click Communications. You will see the screen shown below. Use this screen to enter
communication settings for the meter's two on-board ports: the IrDA Port (COM 1) and
RS485 Port (COM 2) Make any necessary changes to settings
Valid Communication Settings are as follows:
COM1
(IrDA)
Response Delay (0-750 msec)
COM2
(RS485)
Address
(1-247)
Protocol
(Modbus RTU, Modbus ASCII or DNP)
Baud Rate
(9600 to 57600)
Response Delay (0-750 msec)
DNP Options for Voltage, Current, and Power: These fields allow you to choose Primary or
Secondary Units for DNP, and to set custom scaling if you choose Primary. See Chapter 5 in
the GE Communicator EXT USer Manual for more information.
5–8
8.
When changes are complete, click the Update Device button to send a new
profile to the meter.
9.
Click Exit to leave the Device Profile or click other menu items to change
other aspects of the Device Profile (see following section for instructions).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
5.4
Multilin™ EPM7000 Meter Device Profile Settings
Modification to the Device Profile may cause improper Option Card operation due to
changed Scaling, etc. Verify or update Programmable Settings related to any Option Cards
installed in the EPM7000 meter.
Note
Only the basic EPM7000 meter Device Profile Settings are explained in this manual. Refer
to Chapter 5 in the GE Communicator EXT 3.0 User Manual for detailed instructions on
configuring all settings of the meter’s Device Profile. You can view the manual online by
clicking Help>Contents from the GE Communicator EXT Main screen.
CT, PT Ratios and System Hookup:
The screen fields and acceptable entries are as follows:
CT Ratios
CT Numerator (Primary): 1 - 9999
CT Denominator (Secondary): 5 or 1 Amp
Note
This field is display only.
CT Multiplier: 1, 10 or 100
Current Full Scale: Display only.
PT Ratios:
PT Numerator (Primary): 1 - 9999
PT Denominator (Secondary): 40 - 600
PT Multiplier: 1, 10, 100, or 1000
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–9
CHAPTER 5: COMMUNICATION INSTALLATION
Voltage Full Scale: Display only.
System Wiring:
3 Element Wye; 2.5 Element Wye; 2 CT Delta
Note
Voltage Full Scale = PT Numerator x PT Multiplier
Example:
A 14400/120 PT would be entered as:
PT Num:
1440
PT Denom:
120
Multiplier:
10
This example would display a 14.40kV.
Example CT Settings:
200/5 Amps: Set the Ct-n value for 200, Ct-Multiplier value for 1
800/5 Amps: Set the Ct-n value for 800, Ct-Multiplier value for 1
2,000/5 Amps: Set the Ct-n value for 2000, Ct-Multiplier value for 1
10,000/5 Amps: Set the Ct-n value for 1000, Ct-Multiplier value for 10
Example PT Settings:
277/277 Volts: Pt-n value is 277, Pt-d value is 277, Pt-Multiplier is 1
14,400/120 Volts: Pt-n value is 1440, Pt-d value is 120, Pt-Multiplier value is 10
138,000/69 Volts: Pt-n value is 1380, Pt-d value is 69, Pt-Multiplier value is 100
345,000/115 Volts: Pt-n value is 3450, Pt-d value is 115, Pt-Multiplier value is 100
345,000/69 Volts: Pt-n value is 345, Pt-d value is 69, Pt-Multiplier value is 1000
Note
Settings are the same for Wye and Delta configurations.
Display Configuration
The settings on this screen determine the display configuration of the meter’s faceplate.
5–10
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
.
The screen fields and acceptable entries are as follows:
Phases Displayed: A; A and B; A, B, and C. This field determines which phases
display on the faceplate. For example, if you select A and B, only those two phases
will be displayed on the faceplate.
Auto Scroll Display: Yes or No. This field enables/disables the scrolling of selected
readings on the faceplate. If enabled, the readings scroll every 5 seconds.
Enable on Face Plate of Display: Check the boxes of the Readings you want
displayed on the faceplate of the meter. You must select at least one reading.
Power Direction: View as Load or View as Generator
Flip Power Factor Sign: Yes or No.
Current (I) Display Autoscale: On to apply scaling to the current display or Off (No
decimal places).
Display Voltage in Secondary: Yes or No.
Load Bar Custom Configuration: To enter scaling for the Load Bar, click the Load
Bar Custom Configuration checkbox. Fields display on the screen that allow you to
enter a Scaling factor for the display. See the figure below
Enter the scaling factor you want in the Current Scale field. This field is multiplied by the CT
Multiplier set in the CT, PT Ratios, and System Hookup screen (see Section 5.3.3.1) to arrive
at the Primary Full Scale. Make sure you set the CT multiplier correctly.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–11
CHAPTER 5: COMMUNICATION INSTALLATION
Enable Fixed Scale for Voltage Display: To enter a scaling factor for the Voltage display,
click the checkbox next to Enable Fixed Scale for Voltage Display. The screen changes - see
the figure below.
Select the scaling you want to use from the pull-down menu. The options are: 0, 100.0kV,
10.00kV, 0r 0kV.
Energy, Power Scaling, and Averaging
The screen fields and acceptable entries are as follows:
Energy Settings
Energy Digits: 5; 6; 7; 8
Energy Decimal Places: 0 - 6
Energy Scale: unit; kilo (K); Mega (M)
For Example: a reading for Digits: 8; Decimals: 3; Scale: K would be formatted:
00123.456k
Power Settings
Power Scale: Auto; unit; kilo (K); Mega (M)
Apparent Power (VA) Calculation Method: Arithmetic Sum; Vector Sum
Demand Averaging
Type: Block or Rolling
Interval (Block demand) or Sub-Interval (Rolling demand) in minutes: 5; 15; 30; 60
5–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
Number of Subintervals: 1; 2; 3; 4
Interval Window: This field is display only. It is the product of the values entered in the
Sub-Interval and Number of Subintervals fields.
Note
You will only see the Number of Subintervals and Interval Window fields if you select
Rolling Demand.
System Settings
From this screen, you can do the following:
Enable or Disable Password for Reset (Reset Max/Min Energy Settings, Energy
Accumulators, and the Individual Logs) and/or Configuration (Device Profile): click the
radio button next to Yes or No.
Note
• If you enable a Password for Reset, you must also enable it for Configuration.
• The meter’s default is Password Disabled.
• Enabling Password protection prevents unauthorized tampering with devices.
When a user attempts to make a change that is under Password protection, GE
Communicator EXT opens a screen asking for the password. If the correct
Password is not entered, the change does not take place.
Note
You must set up a password before enabling Password Protection. Click the Change button
next to Change Password if you have not already set up a password.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–13
CHAPTER 5: COMMUNICATION INSTALLATION
Change the Password: Click the Change button. You will see the "Enter the New Password"
screen.
Note
1.
Type in the new password (0 - 9999).
2.
Retype the password.
3.
Click Change.
The new password is saved and the meter restarts.
If Password Protection has already been enabled for Configuration and you attempt to
change the password, you will see the Enter Password screen after you click Change. Enter
the old password and click OK to proceed with the password change..
Change the Device Designation: input a new meter designation into this field.
Limits
Limits are transition points used to divide acceptable and unacceptable measurements.
When a value goes above or below the limit, an out-of-limit condition occurs. Once they
are configured, you can view the out-of-Limits (or Alarm) conditions in the Limits Log or
Limits Polling screen. You can also use Limits to trigger relays. See the GE Communicator
EXT User Manual for details.
5–14
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 5: COMMUNICATION INSTALLATION
The current settings for Limits are shown in the screen. You can set and configure up to
eight Limits for the EPM7000 meter.
To set up a Limit:
1.
Select a limit by double-clicking on the Assigned Channel field.
2.
You will see the screen shown below.
Select a Group and an Item for the Limit.
3.
Click OK.
To configure a Limit:
Double-click on the Field to set the following values:
Above and Below Set Point: % of Full Scale (the point at which the reading goes out of
limit)
Examples:
100% of 120V Full Scale = 120V
90% of 120V Full Scale = 108V
Above and Below Return Hysteresis: (the point at which the reading goes back within
limit)
Examples:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
5–15
CHAPTER 5: COMMUNICATION INSTALLATION
Above Set Point = 110%; Below Set Point = 90%
(Out of Limit above 132V);(Out of Limit below 108V)
Above Return Hysteresis = 105%; Below Return Hysteresis = 95%
(Stay Out of Limit until below 126V)(Stay Out of Limit until above 114V).
+ MEASURED VALUE
Above Limit
condition
Above Limit Trigger point
HYSTERESIS
Return point from Above Limit condition
Return point from Below Limit condition
HYSTERESIS
Below Limit Trigger point
Below Limit
condition
0
- MEASURED VALUE
TIME
(if applicable)
Primary Fields: These fields are display only. They show what the set point and return
hysteresis value are for each limit.
Note
• If you are entering negative limits, be aware that the negative value affects the
way the above and below limits function, since negative numbers are processed as
signed values.
• If the Above Return Hysteresis is greater than the Above Set Point, the Above Limit
is Disabled; if the Below Return Hysteresis is less than the Below Set Point, the
Below Limit is Disabled. You may want to use this feature to disable either Above or
Below Limit conditions for a reading.
Note
Note
5–16
When you have finished making changes to the Device Profile, click Update Device to
send the new Profile settings to the meter.
Refer to Chapter 5 of the GE Communicator EXT User’s Manual for additional instructions
on configuring the EPM7000 meter settings, including Time Setting, Transformer and Line
Loss Compensation, CT and PT Compensation, Ethernet card NTP Time Server
Synchronization, Secondary Voltage display, Symmetrical Components, Voltage and
Current Unbalance, and scaling Primary readings for use with DNP.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 6: Using the Multilin™
EPM7000 Meter
™
Using the Multilin
6.1
EPM7000 Meter
Introduction
You can use the Elements and Buttons on the EPM7000 meter’s face to view meter
readings, reset and/or configure the meter, and perform related functions. The following
sections explain the Elements and Buttons and detail their use.
6.1.1
Understanding Meter Face Elements
Reading Type
Indicator
Parameter
Designator
IrDA Com
Port
Watt-hour
Test Pulse
Scaling Factor
% of Load
Bar
FIGURE 6–1: Face Plate with Elements
The meter face features the following elements:
• Reading Type Indicator: e.g., Max
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–1
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
• Parameter Designator: e.g., Volts L-N
• Watt-Hour Test Pulse: Energy pulse output to test accuracy
• Scaling Factor: Kilo or Mega multiplier of displayed readings
• % of Load Bar: Graphic Display of Amps as % of the Load (Refer to Section 6.3 for
additional information.)
• IrDA Communication Port: Com 1 port for wireless communication
6.1.2
Understanding Meter Face Buttons
Menu
Enter
Down
Right
FIGURE 6–2: Face Plate with Buttons
The meter face has Menu, Enter, Down and Right buttons, which let you perform the
following functions:
• View Meter Information
• Enter Display Modes
• Configure Parameters (may be Password Protected)
• Perform Resets (may be Password Protected)
• Perform LED Checks
• Change Settings
• View Parameter Values
• Scroll Parameter Values
• View Limit States
6–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
6.2
Using the Front Panel
You can access four modes using the EPM7000 meter’s front panel buttons:
• Operating Mode (Default)
• Reset Mode
• Configuration Mode
• Information Mode. Information Mode displays a sequence of screens that show
model information, such as Frequency, Amps, Software Options, etc.
Use the Menu, Enter, Down and Right buttons to navigate through each mode and its
related screens.
Note
6.2.1
•
See Appendix A for the complete display mode Navigation maps.
•
The meter can also be configured using software; see Chapter 5 and the GE
Communicator EXT User Manual for instructions.
Understanding Startup and Default Displays
Upon Power Up, the meter displays a sequence of screens:
• Lamp Test Screen where all LEDs are lit
• Lamp Test Screen where all digits are lit
• Firmware Screen showing build number
• Error Screen (if an error exists).
After startup, if auto-scrolling is enabled, the EPM7000 meter scrolls the parameter
readings on the right side of the front panel. The Kilo or Mega LED lights, showing the scale
for the Wh, VARh and VAh readings. Figure 6.3 shows an example of a Wh reading.
FIGURE 6–3: Display Showing Watt-hr Reading
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–3
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
The EPM7000 meter continues to provide scrolling readings until one of the buttons on the
front panel is pressed, causing the meter to enter one of the other Modes.
6.2.2
Using the Main Menu
1.
Press the Menu button. The Main Menu screen appears.
•
The Reset: Demand mode (rStd) appears in the A window. Use the Down
button to scroll, causing the Reset: Energy (rStE), Configuration (CFG),
Operating (OPr), and Information (InFo) modes to move to the A window.
•
The mode that is currently flashing in the A window is the “Active” mode,
which means it is the mode that can be configured.
For example: Press Down Twice - CFG moves to A window. Press Down Twice - OPr moves
to A window.
2.
6.2.3
Press the Enter button from the Main Menu to view the Parameters screen for
the mode that is currently active.
Using Reset Mode
Reset Mode has two options:
6–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
• Reset: Demand (rStd): resets the Max and Min values.
• Reset: Energy (rStE): resets the energy accumulator fields.
1.
Press the Enter button while either rStd or rStE is in the A window. The Reset
Demand No or Reset Energy No screen appears.
•
If you press the Enter button again, the Main Menu appears, with the
next mode in the A window. (The Down button does not affect this
screen.)
•
If you press the Right button, the Reset Demand YES or Reset Energy YES
screen appears. Press Enter to perform a reset.
If Password Protection is enabled for Reset, you must enter the four digit Password before
you can reset the meter. (See Chapter 5 for information on Password Protection.) To enter
a password, follow the instructions in Section 6.2.4.
Note
Reset Demand YES resets all Max and Min values.
2.
6.2.4
Once you have performed a reset, the screen displays either “rSt dMd donE”
or “rSt EnEr donE”and then resumes auto-scrolling parameters.
Entering a Password
If Password Protection has been enabled in the software for Reset and/or Configuration
(see Chapter 5 for more information), a screen appears requesting a Password when you
try to reset the meter and/or configure settings through the front panel. PASS appears in
the A window and 4 dashes appear in the B window. The left-most dash is flashing.
1.
Press the Down button to scroll numbers from 0 to 9 for the flashing dash.
When the correct number appears for that dash, use the Right button to
move to the next dash.
Example: The left screen, below, shows four dashes. The right screen shows the display
after the first two digits of the password have been entered.
2.
When all 4 digits of the password have been selected, press the Enter button.
•
If you are in Reset Mode and you enter the correct Password, “rSt dMd
donE” or “rSt EnEr donE”appears and the screen resumes auto-scrolling
parameters.
•
If you are in Configuration Mode and you enter the correct Password, the
display returns to the screen that required a password.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–5
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
•
If you enter an incorrect Password, “PASS ---- FAIL” appears...
and:
6.2.5
•
The previous screen is re-displayed, if you are in Reset Mode.
•
The previous Operating Mode screen is re-displayed, if you are in
Configuration Mode.
Using Configuration Mode
Configuration Mode follows Reset: Energy on the Main Menu.
To access Configuration Mode:
Note
1.
Press the Menu button while the meter is auto-scrolling parameters.
2.
Press the Down button until the Configuration Mode option (CFG) is in the A
window.
3.
Press the Enter button. The Configuration Parameters screen appears.
4.
Press the Down button to scroll through the configuration parameters: Scroll
(SCrL), CT, PT, Connection (Cnct) and Port. The parameter currently ‘Active,” i.e.,
configurable, flashes in the A window.
5.
Press the Enter button to access the Setting screen for the currently active
parameter.
You can use the Enter button to scroll through all of the Configuration parameters and
their Setting screens, in order.
6.
6–6
Press Enter when CFG is in A window - Parameter screen appears -
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
7.
Note
Press Down- Press Enter when the parameter you want is in the A window.
The parameter screen appears, showing the current settings. To change the
settings:
•
Use either the Down button or the Right button to select an option.
•
To enter a number value, use the Down button to select the number
value for a digit and the Right button to move to the next digit.
When you try to change the current setting and Password Protection is enabled for the
meter, the Password screen appears. See Section 6.2.4 for instructions on entering a
password.
8.
9.
Once you have entered the new setting, press the Menu button twice.
The Store ALL YES screen appears. You can either:
•
Press the Enter button to save the new setting.
•
Press the Right button to access the Store ALL no screen; then press the
Enter button to cancel the Save.
If you have saved the settings, the Store ALL done screen appears and the
meter resets.
Press the Enter button to
save the settings. Press
the Right button for Stor
All no screen.
Press the Enter button to
Cancel the Save.
The settings have been
saved.
6.2.5.1 Configuring the Scroll Feature
When in Auto Scroll mode, the meter performs a scrolling display, showing each
parameter for 7 seconds, with a 1 second pause between parameters. The parameters
that the meter displays are determined by the following conditions:
• They have been selected through software. (Refer to the GE Communicator EXT
User Manual for instructions.)
• They are enabled by the installed Software Option(s). Refer to Section 2.1.3 for
information on Software Options.
To enable or disable Auto-scrolling:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–7
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
Note
1.
Press the Enter button when SCrl is in the A window. The Scroll YES screen
appears
2.
Press either the Right or Down button if you want to access the Scroll no
screen. To return to the Scroll YES screen, press either button.
3.
Press the Enter button on either the Scroll YES screen (to enable autoscrolling) or the Scroll no screen (to disable auto-scrolling).
4.
The CT- n screen appears (this is the next Configuration mode parameter).
• To exit the screen without changing scrolling options, press the Menu button.
• To return to the Main Menu screen, press the Menu button twice.
• To return to the scrolling (or non-scrolling) parameters display, press the Menu
button three times.
6.2.5.2 Configuring CT Setting
The CT Setting has three parts: Ct-n (numerator), Ct-d (denominator), and Ct-S (scaling).
1.
Press the Enter button when Ct is in the A window. The Ct-n screen appears.
You can either:
•
•
Note
Change the value for the CT numerator.
Access one of the other CT screens by pressing the Enter button: press
Enter once to access the Ct-d screen, twice to access the Ct-S screen.
The Ct-d screen is preset to a 5 amp or 1 amp value at the factory and cannot be changed.
2.
To change the value for the CT numerator:
From the Ct-n screen:
6–8
•
Use the Down button to select the number value for a digit.
•
Use the Right button to move to the next digit.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
3.
To change the value for CT scaling
From the Ct-S screen:
•
Use the Right button or the Down button to choose the scaling you
want. The Ct-S setting can be 1, 10, or 100.
If you are prompted to enter a password, refer to Section 6.2.4 for instructions on doing so.
Note
4.
When the new setting is entered, press the Menu button twice.
5.
The Store ALL YES screen appears. Press Enter to save the new CT setting.
Example CT Settings:
200/5 Amps: Set the Ct-n value for 200 and the Ct-S value for 1.
800/5 Amps: Set the Ct-n value for 800 and the Ct-S value for 1.
2,000/5 Amps: Set the Ct-n value for 2000 and the Ct-S value for 1.
10,000/5 Amps: Set the Ct-n value for 1000 and the Ct-S value for 10.
Note
•
The value for Amps is a product of the Ct-n value and the Ct-S value.
•
Ct-n and Ct-S are dictated by primary current; Ct-d is secondary current.
Use buttons to set Ct-n
Press Enter
Ct-d cannot be changed
Use buttons to
select scaling
6.2.5.3 Configuring PT Setting
The PT Setting has three parts: Pt-n (numerator), Pt-d (denominator), and Pt-S (scaling).
1.
2.
Press the Enter button when Pt is in the A window. The PT-n screen appears.
You can either:
•
Change the value for the PT numerator.
•
Access one of the other PT screens by pressing the Enter button: press
Enter once to access the Pt-d screen, twice to access the Pt-S screen.
To change the value for the PT numerator or denominator:
From the Pt-n or Pt-d screen:
3.
•
Use the Down button to select the number value for a digit.
•
Use the Right button to move to the next digit.
To change the value for the PT scaling:
From the Pt-S screen:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–9
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
•
Note
Use the Right button or the Down button to choose the scaling you
want. The Pt-S setting can be 1, 10, 100, or 1000.
If you are prompted to enter a password, refer to Section 6.2.4 for instructions on doing so.
4.
When the new setting is entered, press the Menu button twice.
5.
The STOR ALL YES screen appears. Press Enter to save the new PT setting.
Example PT Settings:
277/277 Volts: Pt-n value is 277, Pt-d value is 277, Pt-S value is 1.
14,400/120 Volts: Pt-n value is 1440, Pt-d value is 120, Pt-S value is 10.
138,000/69 Volts: Pt-n value is 1380, Pt-d value is 69, Pt-S value is 100.
345,000/115 Volts: Pt-n value is 3450, Pt-d value is 115, Pt-S value is 100.
345,000/69 Volts: Pt-n value is 345, Pt-d value is 69, Pt-S value is 1000.
Note
Pt-n and Pt-S are dictated by primary voltage; Pt-d is secondary voltage.
Use buttons to set Pt-n
Use buttons to set Pt-d
Use buttons to select
scaling
6.2.5.4 Configuring Connection Setting
Note
1.
Press the Enter button when Cnct is in the A window. The Cnct screen appears.
2.
Press the Right button or Down button to select a configuration. The choices
are:
3 Element Wye (3 EL WYE)
•
2.5 Element Wye (2.5EL WYE)
•
2 CT Delta (2 Ct dEL)
If you are prompted to enter a password, refer to Section 6.2.4 for instructions on
doing so.
3.
6–10
•
When you have made your selection, press the Menu button twice.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
4.
The STOR ALL YES screen appears. Press Enter to save the setting.
Use buttons to select configuration.
6.2.5.5 Configuring Communication Port Setting
Port configuration consists of: Address (a three digit number), Baud Rate (9600; 19200;
38400; or 57600), and Protocol (DNP 3.0; Modbus RTU; or Modbus ASCII).
1.
2.
Press the Enter button when POrt is in the A window. The Adr (address) screen
appears. You can either:
•
Enter the address.
•
Access one of the other Port screens by pressing the Enter button: press
Enter once to access the bAUd screen (Baud Rate), twice to access the
Prot screen (Protocol).
To enter the Address
From the Adr screen:
3.
•
Use the Down button to select the number value for a digit.
•
Use the Right button to move to the next digit.
To select the Baud Rate:
From the bAUd screen:
•
4.
Use the Right button or the Down button to select the setting you want.
To select the Protocol:
From the Prot screen:
•
Note
Press the Right button or the Down button to select the setting you
want.
If you are prompted to enter a password, refer to Section 6.2.4 for instructions on doing so.
5.
When you have finished making your selections, press the Menu button twice.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–11
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
6.
The STOR ALL YES screen appears. Press Enter to save the settings.
Use buttons to enter
Address
6.2.6
Use buttons to select
Baud Rate
Use buttons to select
Protocol
Using Operating Mode
Operating Mode is the EPM7000 meter’s default mode, that is, the standard front panel
display. After starting up, the meter automatically scrolls through the parameter screens, if
scrolling is enabled. Each parameter is shown for 7 seconds, with a 1 second pause
between parameters. Scrolling is suspended for 3 minutes after any button is pressed.
1.
Press the Down button to scroll all the parameters in Operating Mode. The
currently “Active,” i.e., displayed, parameter has the Indicator light next to it,
on the right face of the meter.
2.
Press the Right button to view additional readings for that parameter. The
table below shows possible readings for Operating Mode. Sheet 2 in Appendix
A shows the Operating Mode Navigation map.
Readings or groups of readings are skipped if not applicable to the meter type or hookup,
or if they are disabled in the programmable settings.
Note
Table 6–1: Operating Mode Parameter Readings - Possible Readings
6–12
VOLTS L-N
VOLTS_LN
VOLTS_LN_MAX
VOLTS_LN_MIN
VOLTS_LN_THD
VOLTS L-L
VOLTS_LL
VOLTS_LL_MAX
VOLTS_LL_MIN
AMPS
AMPS
AMPS_NEUTRAL
AMPS_MAX
AMPS_MIN
W/VAR/PF
W_VAR_PF
W_VAR_PF_MAX
_POS
W_VAR_PF_MIN
_POS
W_VAR_PF_MIN
_NEG
VA/Hz
VA_FREQ
VA_FREQ_MAX
VA_FREQ_MIN
Wh
KWH_REC
KWH_DEL
KWH_NET
KWH_TOT
VARh
KVARH_POS
KVARH_NEG
KVARH_NET
KVARH_TOT
VAh
KVAH
AMPS_THD
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
6.3
Understanding the % of Load Bar
The 10-segment LED bar graph at the bottom left of the EPM7000 meter’s front panel
provides a graphic representation of Amps. The segments light according to the load, as
shown in the table below.
When the Load is over 120% of Full Load, all segments flash “On” (1.5 secs) and “Off” (0.5
secs).
Table 6–2: % of Load Segment Table
Segments
Load ±% Full Load
none
no load
1
1%
1-2
15%
1-3
30%
1-4
45%
1-5
60%
1-6
72%
1-7
84%
1-8
96%
1-9
108%
1-10
120%
All Blink
>120%
10
1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–13
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
6.4
Performing Watt-Hour Accuracy Testing (Verification)
To be certified for revenue metering, power providers and utility companies must verify
that the billing energy meter performs to the stated accuracy. To confirm the meter’s
performance and calibration, power providers use field test standards to ensure that the
unit’s energy measurements are correct. Since the EPM7000 meter is a traceable revenue
meter, it contains a utility grade test pulse that can be used to gate an accuracy standard.
This is an essential feature required of all billing grade meters.
• Refer to Figure 6.5 for an example of how this process works.
• Refer to Table 6.1 for the Wh/Pulse Constants for Accuracy Testing.
Watt-hour
Test Pulse
FIGURE 6–4: Watt-hour Test Pulse
6–14
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
FIGURE 6–5: Using the Watt-hour Test Pulse
Table 6–3: Infrared & KYZ Pulse Constants for Accuracy Testing - Kh Watthour per pulse
Input Voltage Level
Note
Class 10 Models
Class 2 Models
Below 150V
0.500017776
0.1000035555
Above 150V
2.000071103
0.400014221
•
Minimum pulse width is 90 milliseconds.
•
Refer to Chapter 2, Section 2.2, for Wh Pulse specifications.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
6–15
CHAPTER 6: USING THE MULTILIN™ EPM7000 METER
6–16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 7: Using the I/O Option
Cards
Using the I/O Option Cards
7.1
Overview
The EPM7000 meter offers extensive I/O expandability. Using the two universal Option
Card slots, the unit can be easily configured to accept new I/O Option cards even after
installation, without your needing to remove the meter. The EPM7000 meter auto-detects
any installed Option cards. Up to 2 cards of any type outlined in this chapter can be used
per meter.
Option Card
Option Card Slots
FIGURE 7–1: EPM7000 Meter Back, Showing Option Card Slots and I/O Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–1
CHAPTER 7: USING THE I/O OPTION CARDS
7.2
Installing Option Cards
The Option Cards are inserted in one of the two Option Card slots in the back of the
EPM7000 meter.
Remove Voltage Inputs and power supply terminal to the meter before performing card
installation.
Note
1.
Remove the screws at the top and the bottom of the Option Card slot covers.
2.
There is a plastic “track” on the top and the bottom of the slot. The Option card
fits into this track.
WARNING!
For safety, remove
ALL these
connections before
installing Option
Cards (GNC, L, N,
Vref, Va, Vb, Vc).
FIGURE 7–2: Detail of Guide Track
3.
Slide the card inside the plastic track and insert it into the slot. You will hear a
click when the card is fully inserted. Be careful, it is easy to miss the guide
track.
• Make sure the I/O card is inserted properly into the track to avoid damaging
the card’s components.
• For proper card fit, and to avoid damaging the unit, insert components in the
following order:
7–2
•
Option Card 1
•
Option Card 2
•
Detachable terminal block 1
•
Detachable terminal block 2
•
Communication connection for Port 2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
7.3
Configuring Option Cards
FOR PROPER OPERATION, RESET ALL PARAMETERS IN THE UNIT AFTER HARDWARE
MODIFICATION.
The EPM7000 meter auto-detects any Option cards installed in it. You configure the Option
cards through GE Communicator EXT software. Refer to Chapter 5 of the GE Communicator
EXT User Manual for detailed instructions.
The following sections describe the available Option cards.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–3
CHAPTER 7: USING THE I/O OPTION CARDS
7.4
1mA Output Card (C1)
The 1mA card transmits a standardized bi-directional 0-1mA signal. This signal is linearly
proportional to real-time quantities measured by the EPM7000 meter. The outputs are
electrically isolated from the main unit.
7.4.1
Specifications
The technical specifications at 25° C at 5k load are as follows:
Number of outputs:
4 single ended
Power consumption:
1.2 W internal
Signal output range:
-1.2 to +1.2 mA
Max. load impedance:
10 k
Hardware resolution:
12 bits
Effective resolution:
14 bits with 2.5 kHz PWM
Update rate per channel:
100ms
Output accuracy:
± 0.1 % of output range (2.4 mA)
Load regulation
± 0.06 % of output range (2.4 mA)
load step of 5 k @ ± 1 mA
Temperature coefficient
± 30 nA/°C
Isolation:
AC 2500 V system to outputs
Reset/Default output value:
0 mA
The general specifications are as follows:
7.4.2
Operating temperature:
-20 to +70 °C
Storage temperature:
-40 to +80 °C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity Interference:
EN61000-4-2
Weight:
1.6 oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
External connection:
AWG 12-26/(0.29 - 3.31) mm2 5 pin,
0.200” plug-able terminal block
Default Configuration
The EPM7000 meter automatically recognizes the installed option card during Power Up. If
you have not programmed a configuration for the card, the unit will default to the
following outputs:
Channel 1
+Watts, +1800 Watts => +1mA
-Watts, - 1800 Watts => -1mA
7–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
Channel 2
+VARs, +1800 VARs => +1mA
- VARs, -1800 VARs => -1mA
Channel 3
Phase A Voltage WYE, 300 Volts =>
+1mA
Phase A Voltage Delta, 600 Volts =>
+1mA
Channel 4
7.4.3
Phase A Current, 10 Amps => +1mA
Wiring Diagram
FIGURE 7–3: 4-Channel 0 - 1mA Output Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–5
CHAPTER 7: USING THE I/O OPTION CARDS
7.5
20mA Output Card (C20)
The 20mA card transmits a standardized 0-20 mA signal. This signal is linearly proportional
to real-time quantities measured by the EPM7000 meter. The current sources need to be
loop powered. The outputs are electrically isolated from the main unit.
7.5.1
Specifications
The technical specifications at 25° C at 500 load are as follows:
Number of outputs:
4 single ended
Power consumption:
1W internal
Signal output range:
(0 to 24)mA
Max. load impedance:
850 @ 24VDC
Hardware resolution:
12 bits
Effective resolution:
14 bits with 2.5kHz PWM
Update rate per channel:
100ms
Output accuracy:
± 0.1% of output range (24mA)
Load regulation:
± 0.03% of output range (24mA)
load step of 200 @ 20mA
Temperature coefficient
± 300n A/°C
Isolation:
AC 2500V system to outputs
Maximum loop voltage:
28Vdc max.
Internal voltage drop:
3.4VDC @ 24mA
Reset/Default output value:
12mA
The general specifications are as follows:
7.5.2
Operating temperature:
(-20 to +70) °C
Storage temperature:
(-40 to +80) °C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity interference:
EN61000-4-2
Weight:
1.6oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
External connection:
AWG 12-26/(0.129 - 3.31)mm2 5 pin,
0.200” plug-able terminal block
Default Configuration
The EPM7000 meter automatically recognizes the installed option card during Power
Up. If you have not programmed a configuration for the card, the unit will default to
the following outputs:
7–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
Channel 1
+Watts, +1800 Watts => 20mA
-Watts, -1800 Watts => 4mA
0 Watts => 12mA
Channel 2
+VARs, +1800 VARs => 20mA
- VARs, -1800 VARs => 4mA
0 VARs => 12mA
Channel 3
Phase A Voltage WYE, 300 Volts =>
20mA
0 Volts => 4 mA
Phase A Voltage Delta, 600 Volts =>
20mA
Channel 4
Phase A Current, 10 Amps => 20mA
0 Phase A Current, 0 Amps => 4 mA
7.5.3
Wiring Diagram
FIGURE 7–4: 4-Channel 0 - 20mA Output Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–7
CHAPTER 7: USING THE I/O OPTION CARDS
7.6
Digital Output (Relay Contact) / Digital Input Card (RS1)
The Digital Output/Input card is a combination of relay contact outputs for load switching
and dry/wet contact sensing digital inputs. The outputs are electrically isolated from the
inputs and from the main unit.
7.6.1
Specifications
The technical specifications at 25 °C are as follows:
Power consumption:
0.320W internal
Relay outputs:
Number of outputs:
2
Contact type:
Changeover (SPDT)
Relay type:
Mechanically latching
Switching voltage:
AC 250V / DC 30V
Switching power:
1250VA / 150W
Switching current:
5A
Switching rate max.:
10/s
Mechanical life:
5 x 107 switching operations
Electrical life:
105 switching operations at rated
current
Breakdown voltage:
AC 1000V between open contacts
Isolation:
AC 3000V / 5000V surge system to
contacts
Reset/Power down state:
No change - last state is retained
Inputs:
Number of Inputs:
2
Sensing type:
Wet or dry contact status detection
Wetting voltage:
DC (12-24)V, internally generated
Input current:
2.5mA – constant current regulated
Minimum input voltage:
0V (input shorted to common)
Maximum input voltage:
DC 150V (diode protected against
polarity reversal)
Filtering:
De-bouncing with 50ms delay time
Detection scan rate:
100ms
Isolation:
AC 2500V system to inputs
The general specifications are as follows:
Operating temperature:
7–8
-20 to +70 °C
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
7.6.2
Storage temperature:
-40 to +80 °C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity Interference:
EN61000-4-2
Weight:
1.5oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
External Connection:
AWG 12-26/(0.129 - 3.31) mm2 9 pin,
0.200” plug-able terminal block
Wiring Diagram
Status
Inputs
C
S
T
A
T
U
S
I1
I2
NO
2
C
NC
NO
1
C
NC
Relay
Outputs
FIGURE 7–5: Relay Contact (2) / Status Input (2) Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–9
CHAPTER 7: USING THE I/O OPTION CARDS
7.7
Pulse Output (Solid State Relay Contacts) / Digital Input Card (PS1)
The Pulse Output/Digital Input card is a combination of pulse outputs via solid state
contacts and dry/wet contact sensing digital inputs. The outputs are electrically isolated
from the inputs and from the main unit.
7.7.1
Specifications
The technical specifications at 25 °C are as follows:
Power consumption:
0.420W internal
Relay outputs:
Number of outputs:
4
Contact type:
Closing (SPST - NO)
Relay type:
Solid state
Peak switching voltage:
DC ±350V
Continuous load current:
120mA
Peak load current:
350mA for 10ms
On resistance, max.:
35
Leakage current:
1µ[email protected]
Switching Rate max.:
10/s
Isolation:
AC 3750V system to contacts
Reset/Power down state:
Open contacts
Inputs:
Number of inputs:
4
Sensing type:
Wet or dry contact status detection
Wetting voltage:
DC (12-24)V, internally generated
Input current:
2.5mA – constant current regulated
Minimum input voltage:
0V (input shorted to common)
Maximum input voltage:
DC 150V (diode protected against
polarity reversal)
Filtering:
De-bouncing with 50ms delay time
Detection scan rate:
100ms
Isolation:
AC 2500V system to inputs
The general specifications are as follows:
7–10
Operating Temperature:
(-20 to +70) °C
Storage Temperature:
(-40 to +80) °C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity Interference:
EN61000-4-2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
7.7.2
Weight:
1.3oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
External Connection:
AWG 12-26/(0.129 - 3.31) mm213
pin, 3.5mm plug-able terminal block
Default Configuration:
The EPM7000 meter automatically recognizes the installed option card during Power Up. If
you have not programmed a configuration for the card, the unit will default to the
following outputs:
7.7.3
Status Inputs
Defaulted to Status Detect
Pulse Outputs
Defaulted to Energy Pulses
Pulse Channel 1
1.8 +Watt-hrs per pulse
Pulse Channel 2
1.8 -Watt-hrs per pulse
Pulse Channel 3
1.8 +VAR-hrs per pulse
Pulse Channel 4
1.8 -VAR-hrs per pulse
Wiring Diagram
Status
Inputs
S
T
A
T
U
S
4
3
2
1
C
I4
I3
I2
I1
NO
C
NO
C
NO
C
NO
C
Pulse
Outputs
FIGURE 7–6: Pulse Output (4) / Status Input (4) Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–11
CHAPTER 7: USING THE I/O OPTION CARDS
7.8
Fiber Optic Communication Card (F1; F2)
The Fiber Optic Communication card provides a standard serial communication port via a
fiber optic connection. An echo switch is available to enable messages bypassing the unit.
This feature can be used in a daisy chained network topology.
7.8.1
Specifications
The technical specifications at 25 °C are as follows:
Number of Ports:
1
Power consumption:
0.160W internal
Fiber connection:
ST® (F1) or Versatile Link (F2) – as
per order
Optical fiber details:
Multimode
ST® (FOSTS)
50/125 µm, 62.5/125 µm, 100/140
µm,
200µm Hard Clad Silica (HCS®)
Versatile Link (FOVPS):
200µm Hard Clad Silica (HCS®)
1mm Plastic Optical Fiber (POF)
Baud rate:
Up to 57.6kb/s – pre-programmed
in the main unit
Diagnostic feature:
LED lamps for TX and RX activity
The general specifications are as follows:
Operating Temperature:
-20 to +70 °C
Storage Temperature:
-40 to +80 °C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity Interference:
EN61000-4-2
Weight:
1.2oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
Fiber Connection:
ST® (FOST) or Versatile Link (FOVP) –
as per order
HCS® is a registered trademark of SpecTran Corporation.
ST® is a registered trademark of AT&T.
7–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
7.8.2
Wiring Diagram
ST® type connector
Echo
switch
Setting the Echo Switch
Fiber
Optic
Port
onnec
ection,
on, set ECH
CHO to OFF
FF
For a Point to Point Conn
ECHO
OFF
ECH
CHO
ON
RX
Meter
ON
TX
RX
TX
TX
RX
OFF
FF
Host
st
TX
onnec
ection
on,, set ECH
CHO tto ON
For a Daisy Chained Conn
RX
ECH
CHO
Meter
1
Fiber
Daisy
Chain
RX
TX
TX
RX
OFF
FF
ON
Host
st
ECH
CHO
RX
Meter ON OFF
FF
2
ON
TX
ECH
CHO
RX
Meter ON OFF
FF
N
ON
TX
Versatile Link type connector
Echo
switch
Fiber
Optic
Port
ECHO
OFF
ON
TX
RX
TX
RX
Fiber
Daisy
Chain
*When a Fiber Optic Com Card is used in point
to point connection, set the Echo Switch to OFF.
* *When a Fiber Optic Com Card is installed in a
meter that is part of a Daisy Chained
connection, set the Echo Switch to ON. this
allows messages not for this meter to continue
to the next meter in sequence.
FIGURE 7–7: Fiber Optic Communication Card
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–13
CHAPTER 7: USING THE I/O OPTION CARDS
7.9
10/100BaseT Ethernet Communication Card (E1)
The 10/100BaseT Ethernet Communication card provides the EPM7000 meter with
Ethernet capability. See Chapter 8 for details and instructions.
Refer to Chapter 5 of the GE Communicator EXT User’s Manual for instructions on
performing Network configuration.
Note
7.9.1
Specifications
The technical specifications at 25 °C are as follows:
Number of Ports:
1
Power consumption:
2.1W internal
Baud rate:
10/100Mbit
Diagnostic feature:
Number of simultaneous Modbus
connections:
Status LEDs for LINK and ACTIVE
12
The general specifications are as follows:
7.9.2
Operating Temperature:
-20 to +70°C
Storage Temperature:
-40 to +80°C
Relative air humidity:
Maximum 95%, non-condensing
EMC - Immunity Interference:
EN61000-4-2
Weight:
1.7oz
Dimensions (inch) W x H x L:
0.72 x 2.68 x 3.26
Connection Type:
RJ45 modular (Auto-detecting
transmit and receive)
Default Configuration
The EPM7000 meter automatically recognizes the installed option card during Power Up. If
you have not programmed a configuration for the card, the unit will default to the
following:
IP Address: 10.0.0.2
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
7–14
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 7: USING THE I/O OPTION CARDS
7.9.3
Wiring Diagram
10/100
BaseT
Ethernet
ACTIVE
Pin 1
LINK
Total
WEB
Solutions
RJ45
45 Plug
8
7
6
5
4
3
2
1
RDRD
Cab
able
RD
RD+
TDTD+
FIGURE 7–8: 10/100BaseT Ethernet Card
Note
The INP100S uses an auto-detecting circuit that automatically switches the transmit and
receive in order to properly align communication. Because of this, when you are
communicating directly to a meter with a PC or a switch, a straight cable can be used.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
7–15
CHAPTER 7: USING THE I/O OPTION CARDS
.
7–16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 8: Using the Ethernet Card
Using the Ethernet Card
8.1
Overview
When you install the optional Ethernet card in your EPM7000 meter, you gain the capability
of communicating over the Ethernet medium using GE Multilin’s communications
technology.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
8–1
CHAPTER 8: USING THE ETHERNET CARD
8.2
Hardware Connection
The Ethernet card fits into either of the two Option Card slots in the back of the EPM7000
meter. Refer to the Chapter 7 for card installation instructions.
Use a standard RJ45 10/100BaseT cable to connect to the Ethernet card. The card autodetects cable type and will work with either straight or crossover cable.
RJ45 cable
connects here
FIGURE 8–1: Meter with Ethernet Card
8–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 8: USING THE ETHERNET CARD
8.3
Performing Network Configuration
As with the other Option cards, the EPM7000 meter auto-detects the presence of an
installed Ethernet card. Configure the Ethernet card through GE Communicator EXT. Refer
to Chapter 5 of the GE Communicator EXT User Manual for instructions. You can open the
manual online by clicking Help>Contents from the GE Communicator EXT Main screen.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
8–3
CHAPTER 8: USING THE ETHERNET CARD
8.4
Ethernet Card Features
The INP100S Ethernet card gives your meter the following capabilities:
• Ethernet Communication
• Embedded Web Server
• NTP Time Server Synchronization
8.4.1
Ethernet Communication
The 100BaseT Ethernet communication card enables high-speed Ethernet communication
with up to 12 simultaneous connections for Modbus TCP. The card supports a static IP
address and is treated like a node on the network.
8.4.2
Embedded Web Server
The Ethernet card gives the meter a Web server that is viewable over the Ethernet by
almost all browsers. The EPM7000 web pages allow you to see the following information
for the EPM7000 meter:
• Voltage and Current Readings
• Power and Energy Readings
• Power Quality Information
• General Meter Information. You can also upgrade the Ethernet (Network)
Card’s firmware from the Meter Information web page.
Follow these steps to access the EPM7000 meter’s web pages:
8–4
1.
Open Internet Explorer from your PC.
2.
Type the Ethernet Card’s IP address in the address bar, preceded by http://.
For example: http://172.20.167.99
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 8: USING THE ETHERNET CARD
3.
You will see the Multilin™ EPM 7000
Power Quality Meter Introduction web page shown below.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
8–5
CHAPTER 8: USING THE ETHERNET CARD
4.
8–6
To view Voltage and Current Readings, click Volts/Amps on the left side of the web
page. You will see the web page shown below:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 8: USING THE ETHERNET CARD
5.
To view Power and Energy Readings, click Power/Energy on the left side of the web
page. You will see the web page shown below:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
8–7
CHAPTER 8: USING THE ETHERNET CARD
6.
To view Power Quality Information, click Power Quality on the left side of the web
page. You will see the web page shown below:
Graph Icon
7.
To view a graphical representation of the voltage and current magnitudes, click the
Graph icon (shown above) in the corner of the Voltage/Current box.
8.
Click Power Quality on the menu at the top of the web page to return to the previous
screen.
9.
To view Meter Information, or to upgrade the Network Card’s firmware, click Meter
Information on the menu at the top of the web page.
8.4.2.1 Upgrading the Ethernet Card’s Firmware
From one of the EPM7000 meter’s web pages:
Note
8–8
1.
Click Meter Information on the menu at the top of the web page.
2.
Click Upgrade Network Card (bottom box on the right).
You will see the window shown below.
In order to upgrade the Network (Ethernet) Card, you must be using the PC on which the
upgrade file is stored.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
CHAPTER 8: USING THE ETHERNET CARD
3.
Click the Browse button to locate the Upgrade file.
4.
Enter the safety code (supplied with the Upgrade file) and the password:
manager.
5.
Click Submit. The upgrade will start immediately (it may take several minutes
to complete). Once the upgrade is complete, you will see a confirmation
message.
Note the Warning message on the screen. If there is a power interruption during
upgrade, please call GE Multilin’s Technical Support department for assistance.
8.4.3
NTP Time Server Synchronization
The network card can be configured to perform time synchronization through a Network
Time Protocol (NTP) server. This feature lets you synchronize the EPM7000 meter’s realtime clock with this outside source. See Chapter 5 of the GE Communicator EXT USer
Manual for configuration instructions (Configuring the Network Card section). You can view
the manual online by clicking Help>Contents from the GE Communicator EXT Main screen.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
8–9
CHAPTER 8: USING THE ETHERNET CARD
8–10
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Chapter 9: Data Logging
Data Logging
9.1
Overview
Software Options C to F give the EPM7000 meter additional memory for extensive data
logging (see section 9.2 below). The EPM7000 meter can log historical trends, limit alarms,
I/O changes, sequence of events, and waveforms (Options E and F only). In addition, the
meter has a real-time clock that allows all events to be time-stamped when they occur.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
9–1
CHAPTER 9: DATA LOGGING
9.2
Available Logs
The following logs are available for an EPM7000 meter equipped with Software Options B
through D. These meters have 2 MegaBytes of flash memory for data logging.
• Historical Logs: The EPM7000 meter has three Historical Logs. Each log can be
independently programmed with individual trending profiles, that is, each can be
used to measure different values. You can program up to 64 parameters per log.
You also have the ability to allocate available system resources between the three
logs, to increase or decrease the size of the individual historical logs. See Chapter 5
(Configuring Historical Logs and Allocating Historical Log Sectors sections) and
Chapter 8 (Viewing Log section) of the GE Communicator EXT User Manual for
additional information and instructions.
• Limit/Alarm Log: This log provides the magnitude and duration of events that fall
outside of configured acceptable limits. Time stamps and alarm value are
provided in the log. Up to 2,048 events can be logged. See Chapter 5 (Configuring
Limits section) and Chapter 8 (EPM7000 Meter Logs section) of the GE
Communicator EXT User Manual for additional information and instructions.
• I/O Change Log: This log is unique to the EPM7000 meter. The I/O Change Log
provides a time-stamped record of any Relay Output/Digital Input or Pulse Output/
Digital Input Card output or input status changes. Up to 2,048 events can be
logged. Refer to Chapter 5 (Configuring EPM7000 Meter Option Cards section) and
Chapter 8 (EPM7000 Meter Logs section) of the GE Communicator EXT User Manual
for additional information and instructions.
• System Events Log: In order to protect critical billing information, the EPM7000
meter records and logs the following information with a timestamp:
•
Demand resets
•
Password requests
•
System startup
•
Energy resets
•
Log resets
•
Log reads
•
Programmable settings changes.
A EPM7000 meter equipped with Options B, C, and D, has 2 MB of additional memory for
data logging: Option E gives the meter 3 Megabytes of flash memory, and Option F gives
the meter 4 MegaBytes of flash memory. These meters also have waveform recording
capabilities, and the following additional log:
• Waveform Log: This event-triggered log records a waveform when a userprogrammed value goes out of limit and when the value returns to normal.
All of the EPM7000 meter Logs can be viewed through the Log Viewer. Refer to Chapter 8 of
the GE Communicator EXT User Manual for additional information and instructions
regarding Logs and the Log Viewer.
9–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Appendix A: Multilin™ EPM7000
Meter Navigation
Multilin
A.1
™
EPM7000 Meter Navigation Maps
Introduction
You can configure the EPM7000 meter and perform related tasks using the buttons on the
meter face. Chapter 6 contains a description of the buttons on the meter face and
instructions for programming the meter using them. The meter can also be programmed
using software (see Chapter 5 and the GE Communicator EXT 3.0 User Manual).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
A–1
APPENDIX A: MULTILIN™ EPM7000 METER NAVIGATION MAPS
A.2
Navigation Maps (Sheets 1 to 4)
The EPM7000 meter’s Navigation maps begin on the next page. The maps show in detail
how to move from one screen to another and from one Display Mode to another using the
buttons on the face of the meter. All Display Modes automatically return to Operating
Mode after 10 minutes with no user activity.
EPM7000 Meter Navigation Map Titles:
• Main Menu Screens (Sheet 1)
• Operating Mode Screens (Sheet 2)
• Reset Mode Screens (Sheet 3)
• Configuration Mode Screens (Sheet 4)
A–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX A: MULTILIN™ EPM7000 METER NAVIGATION MAPS
STARTUP
sequence run once at meter startup:
2 lamp test screens, hardware information
screen, firmware version screen,
(conditional) error screens
10 minutes with no user activity
sequence completed
MENU
MAIN MENU:
OPR (blinking)
RSTD
RSTE
OPERATING MODE
ENTER
DOWN
RESET DEMAND MODE
ENTER
DOWN
DOWN
10 minutes
with no
user activity
MENU
MAIN MENU:
RSTD (blinking)
RSTE
CFG
sequence
completed
grid of meter data screens.
See sheets 2 & 3
sequence of screens to get password, if
required, and reset max/min data.
See sheet 4
MENU
MAIN MENU:
RSTE (blinking)
CFG
INFO
RESET ENERGY MODE
ENTER
DOWN
sequence of screens to get password, if
required, and reset energy accumulators.
See sheet 4
Reset Energy Mode is not
available for SHVA120,
SHAA5, or SHWA300.
MENU
MAIN MENU:
CFG (blinking)
INFO
OPR
CONFIGURATION MODE
ENTER
DOWN
grid of meter settings screens with
password-protected edit capability.
See sheet 5
Configuration Mode is not
available during a
Programmable Settings
update via a COM port.
MENU
MAIN MENU:
INFO (blinking)
OPR
RSTD
INFORMATION
ENTER
sequence of screens to show model
information, same as STARTUP except
lamp tests omitted.
MAIN MENU Screen
MAIN MENU screen scrolls through 5 choices,
showing 3 at a time. The top choice is always the
"active" one, which is indicated by blinking the legend.
SYMBOLS
BUTTONS
MENU
Returns to previous menu from any screen in any mode
ENTER
Indicates acceptance of the current screen and advances to the
next one
DOWN, RIGHT
Navigation:
Navigation and edit buttons
No digits or legends are blinking. On a menu, down advances
to the next menu selection, right does nothing. In a grid of
screens, down advances to the next row, right advances to the
next column. Rows, columns, and menus all navigate circularly.
A digit or legend is blinking to indicate that it is eligible for
change. When a digit is blinking, down increases the digit
value, right moves to the next digit. When a legend is blinking,
either button advances to the next choice legend.
single screen
all screens
for a display
mode
group of
screens
Editing:
action taken
button
FIGURE A–1: Main Menu Screens
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
A–3
APPENDIX A: MULTILIN™ EPM7000 METER NAVIGATION MAPS
See Notes 1 & 3
RIGHT
See Notes 1 & 3
See Notes 1 & 3
RIGHT
VOLTS_LN_MA
RIGHT
VOLTS_LN_MIN
X
VOLTS_LN_MA
RIGHT
RIGHT
VOLTS_LN_MIN
X
RIGHT
VOLTS_LN
VOLTS_LN
DOWN2
See Notes 1 & 3
RIGHT
RIGHT
VOLTS_LN_THD
VOLTS_LN_THD
Yellow is
V-switches 1-3
Yellow is
Yellow is 1-3
V-switches
DOWN2
(from any VOLTS_LN screen)
2
DOWN
DOWN2
RIGHT
(from any VOLTS_LN screen)
See Note 1
RIGHT
VOLTS_LL
RIGHT
VOLTS_LL_MAX
RIGHT
VOLTS_LL
VOLTS_LL_MAX
RIGHT
See Notes 1 & 5
See Note 1
RIGHT
See Notes 1 & 5
RIGHT
VOLTS_LL_MIN
RIGHT
VOLTS_LL_MIN
VOLTS_LL_THD
Options 1 to 3.
Blue is
is Option
Blue
V-switch
3 only
3 only.
Blue is
V-switch 3 only
VOLTS_LL_THD
DOWN2
(from any VOLTS_LL screen)
2
DOWN
(from any VOLTS_LL screen)
See Note 1
RIGHT
RIGHT
AMPS
RIGHT
AMPS
RIGHT
IN
RIGHT
IN
DOWN2
See Note 1
See Note 1
RIGHT
RIGHT
AMPS_MAX
RIGHT
AMPS_MAX
See Note 1
RIGHT
AMPS_MIN
RIGHT
AMPS_MIN
AMPS_THD
AMPS_THD
DOWN2
(from any AMPS screen)
2
DOWN
DOWN2
RIGHT
(from any AMPS screen)
RIGHT
W_VAR_PF
RIGHT
W_VAR_PF
W_VAR_PF
_MAX_POS
W_VAR_PF
_MAX_POS
RIGHT
RIGHT
RIGHT
W_VAR_PF
_MIN_POS
W_VAR_PF
_MIN_POS
See Note 1
See Note 1
RIGHT
RIGHT
W_VAR_PF
_MAX_NEG
W_VAR_PF
_MAX_NEG
RIGHT
RIGHT
W_VAR_PF
_MIN_NEG
W_VAR_PF
_MIN_NEG
DOWN2
DOWN2
DOWN2
(from any W_VAR_PF screen)
2
DOWN
(from any W_VAR_PF screen)
See Note 1
RIGHT
See Note 1
RIGHT
RIGHT
VA_FREQ
RIGHT
VA_FREQ
RIGHT
VA_FREQ_MAX
VA_FREQ_MAX
RIGHT
VA_FREQ_MIN
VA_FREQ_MIN
DOWN2
(from any VA_FREQ screen)
2
DOWN
(from any VA_FREQ screen)
See Note 1
RIGHT
See Note 1
RIGHT
RIGHT
KWH_REC
RIGHT
KWH_REC
RIGHT
KWH_DEL
RIGHT
KWH_DEL
RIGHT
KWH_NET
KWH_NET
RIGHT
KWH_TOT
KWH_TOT
DOWN2
(from any KWH screen)
2
DOWN
(from any KWH screen)
See Note 1
RIGHT
See Note 1
RIGHT
RIGHT
KVARH_POS
RIGHT
KVARH_POS
RIGHT
KVARH_NEG
KVARH_NEG
RIGHT
RIGHT
KVARH_NET
KVARH_NET
RIGHT
KVARH_TOT
KVARH_TOT
DOWN2
(from any KVARH screen)
2
DOWN
See Note
(from any KVARH screen)
1
See Note 1
KVAH
KVAH
MENU
(from any
MENU
operating mode
(from any
screen)
operating mode
screen)
Notes
1 Group
Notes is skipped if not applicable to the meter type or hookup or if explicitly disabled via
programmable
settings.if not applicable to the meter type or hookup or if explicitly disabled via
1 Group is skipped
2 DOWN
occurs without
user intervention every 7 seconds if scrolling is enabled.
programmable
settings.
3 No
Volts LN
screens
for Delta
hookup.every 7 seconds if scrolling is enabled.
2 DOWN
occurs
without
user2CT
intervention
4 Scrolling
is suspended
minutes
any button press.
3 No Volts
LN screensfor
for3Delta
2CTafter
hookup.
5 Volts_LL_THD
screen is for
2CT hookup
only.
4 Scrolling is suspended
forDelta
3 minutes
after any
button press.
5 Volts_LL_THD screen is for Delta 2CT hookup only.
to Main Menu
to sheet
Main Menu
see
1
see sheet 1
FIGURE A–2: Operating Mode Screen
A–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX A: MULTILIN™ EPM7000 METER NAVIGATION MAPS
from MAIN MENU
from MAIN MENU
(RSTD selected)
(RSTE selected)
This path not available for
SHVA120, SHAA5, SHWA300
RESET_ENERGY_NO:
RST
ENER
no (blinking)
ENTER
RESET_MM_NO:
RST
DMD
no (blinking)
RIGHT
RIGHT
RIGHT
RESET_ENERGY_YES:
RST
ENER
yes (blinking)
RIGHT
RESET_MM_YES:
RST
DMD
yes (blinking)
ENTER
ENTER
is password required?
is password required?
yes
yes
increment
blinking digit
DOWN
energy
no
RESET_ENTER_PW:
PASS
#### (one # blinking)
make next digit
blink
RIGHT
demand
no
ENTER
is password
correct?
ENTER
yes
reset all max &
min values
reset all max &
min values
energy
which reset?
demand
which reset?
RESET_MM_CONFIRM:
RST
DMD
DONE
no
2 sec
RESET_PW_FAIL:
PASS
####
FAIL
RESET_ENERGY_CONFIRM:
RST
ENER
DONE
2 sec.
2 sec.
to previous operating
mode screen
see sheet 2
to previous operating
mode screen
see sheet 2 or 3
MENU
(from any
reset mode
screen)
to Main Menu
see sheet 1
FIGURE A–3: Reset Mode Screens
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
A–5
APPENDIX A: MULTILIN™ EPM7000 METER NAVIGATION MAPS
See Note 1
CONFIG_MENU:
SCRL (blinking)
CT
PT
ENTER
DOWN
DOWN or
RIGHT3
toggle
scroll
setting
ENTER
MENU
ENTER
CONFIG_MENU:
CT (blinking)
PT
CNCT
DOWN
SCROLL_EDIT:
SCRL
yes or no
(choice blinking if edit)
ENTER
ENTER
CTN_EDIT:
DOWN
increment
blinking
digit
MENU
CONFIG_MENU:
PT (blinking)
CNCT
PORT
CT-N
####
(one # blinking if edit)
CTD_SHOW:
CT-D
1 or 5
RIGHT
blink
next
digit
ENTER
DOWN
increment
blinking
digit
MENU
ENTER
PTD_EDIT:
PT-N
####
(one # blinking if edit)
RIGHT
blink
next
digit
DOWN
increment
blinking
digit
PT-D
####
(one # blinking if edit)
RIGHT
blink
next
digit
PT_MULT_EDIT:
PT-S
1 or 10 or 100 or 1000
(choice blinking if edit)
DOWN or
RIGHT
show
next
choice
DOWN
MENU
CONFIG_MENU:
CNCT (blinking)
PORT
PASS2
DOWN
CONNECT_EDIT:
CNCT
1 of 3 choices
(choice blinking if edit)
ENTER
MENU2
DOWN
increment
blinking
digit
DOWN
increment
blinking
digit
RIGHT
blink
next
digit
yes
MENU
see sheet 1
MENU
PASSWORD_EDIT:
PASS
#### (one # blinking)
SAVE_YES:
STOR
ALL?
yes (blinking)
RIGHT RIGHT
SAVE_NO:
STOR
ALL?
no (blinking)
DOWN or
RIGHT
show
next
choice
PROTOCOL_EDIT:
PROT
1 of 3 choices
(choice blinking if edit)
DOWN or
RIGHT
show
next
choice
ENTER2
RIGHT
blink
next
digit
Notes:
1. Initial access is view-only. View access shows the existing settings. At the
first attempt to change a setting (DOWN or RIGHT pressed), password is
requested (if enabled) and access changes to edit. Edit access blinks the digit
or list choice eligible for change and lights the PRG LED.
2. Skip over password edit screen and menu selection if access is view-only
or if password is disabled.
3. Scroll setting may be changed with view or edit access.
4. ENTER accepts an edit; MENU abandons it.
first DOWN or RIGHT in view
access (if password required)
ENTER
save new
configuration
DOWN
CFG_ENTER_PW:
PASS
### (one # blinking)
increment
blinking
digit
RIGHT
yes
blink
next
digit
is password
correct?
no
reboot
ENTER
See Note 1
ENTER
SAVE_CONFIRM:
STOR
ALL
DONE
2 sec.
to Main Menu
ENTER
BAUD_EDIT:
BAUD
##.#
(choice blinking if edit)
MENU
(per row of the originating screen)
MENU
no
ADDRESS_EDIT:
ADR
###
(one # blinking if edit)
ENTER
CONFIG_MENU screen
scrolls through 6 choices,
showing 3 at a time. The
top choice is always the
"active" one, indicated by
blinking the legend.
PROT choices:
MOD RTU,
MOD ASCI,
DNP
ENTER
ENTER
CONFIG_MENU:
PASS2 (blinking)
SCRL
CT
any changes?
CNCT choices:
3 EL WYE,
2 CT DEL,
2.5EL WYE
DOWN or
RIGHT
show
next
choice
MENU
CONFIG_MENU:
PORT (blinking)
PASS2
SCRL
DOWN2
ENTER
ENTER
ENTER
DOWN or
RIGHT
show
next
choice
ENTER
ENTER
PTN_EDIT:
DOWN
CT_MULT_EDIT:
CT-S
1 or 10 or 100
(choice blinking if edit)
to the originating
EDIT screen
to previous operating
mode screen
see sheet 2 or 3
FIGURE A–4: Configuration Mode Screens
A–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Appendix B: Modbus Map and
Retrieving Logs
Modbus Map and Retrieving Logs
B.1
Introduction
The Modbus Map for the EPM7000 Meter gives details and information about the possible
readings of the meter and its programming. The EPM7000 meter can be programmed
using the buttons on the face of the meter (Chapter 6), or by using software. For a
programming overview, see section 5.2 of this manual. For further details see the GE
Communicator EXT User's Manual.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–1
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.2
Modbus Register Map Sections
The EPM7000 meter's Modbus Register Map includes the following sections:
Fixed Data Section, Registers 1- 47, details the Meter's Fixed Information.
Meter Data Section, Registers 1000 - 12031, details the Meter's Readings, including
Primary Readings, Energy Block, Demand Block, Phase Angle Block, Status Block, THD
Block, Minimum and Maximum in Regular and Time Stamp Blocks, Option Card Blocks, and
Accumulators. Operating Mode readings are described in Section 6.2.6.
Commands Section, Registers 20000 - 26011, details the Meter's Resets Block,
Programming Block, Other Commands Block and Encryption Block.
Programmable Settings Section, Registers 30000 - 33575, details all the setups you can
program to configure your meter.
Secondary Readings Section, Registers 40001 - 40100, details the Meter's Secondary
Readings.
Log Retrieval Section, Registers 49997 - 51095, details Log Retrieval. See Section B.5 for
instructions on retrieving logs.
B–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.3
Data Formats
ASCII:
ASCII characters packed 2 per register in high, low order and without any
termination characters.
SINT16/UINT16:
16-bit signed/unsigned integer.
SINT32/UINT32:
32-bit signed/unsigned integer spanning 2 registers. The lower-addressed
register is the high order half.
FLOAT:
32-bit IEEE floating point number spanning 2 registers. The lower-addressed
register is the high order half (i.e. contains the exponent).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–3
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.4
Floating Point Values
Floating Point Values are represented in the following format:
Register
0
Byte
1
0
1
0
1
Bit
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Meaning
s
e
e
e
e
e
e
e
e
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
sign
exponent
mantissa
The formula to interpret a Floating Point Value is:
-1sign x 2 exponent-127 x 1.mantissa = 0x0C4E11DB9
-1sign x 2 137-127 x 1· 1000010001110110111001
-1 x 210 x 1.75871956
-1800.929
Register
0x0C4E1
Byte
0x01DB9
0x0C4
Bit
Meaning
0x0E1
0x01D
0x0B9v
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
1
1
0
0
0
1
0
0
1
1
1
0
0
0
0
1
0
0
0
1
1
1
0
1
1
0
1
1
1
0
0
1
s
e
e
e
e
e
e
e
e
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
sign
exponent
mantissa
1
0x089 + 137
0b011000010001110110111001
Formula Explanation:
C4E11DB9 (hex): 11000100 11100001 00011101 10111001 (binary)
The sign of the mantissa (and therefore the number) is 1, which represents a negative
value.
The Exponent is 10001001 (binary) or 137 decimal.
The Exponent is a value in excess 127. So, the Exponent value is 10.
The Mantissa is 11000010001110110111001 binary.
With the implied leading 1, the Mantissa is (1).611DB9 (hex).
The Floating Point Representation is therefore -1.75871956 times 2 to the 10.
Decimal equivalent: -1800.929
Note
B–4
•
Exponent = the whole number before the decimal point.
•
Mantissa = the positive fraction after the decimal point.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.5
Retrieving Logs Using the EPM7000 Meter's Modbus Map
This section describes the log interface system of the EPM7000 meter from a programming
point of view. It is intended for Programmers implementing independent drivers for Log
Retrieval from the meter. It describes the meaning of the meter's Modbus Registers related
to Log Retrieval and Conversion, and details the procedure for retrieving a log's records.
Note
B.5.1
•
All references assume the use of Modbus function codes 0x03, 0x06, and 0x10, where
each register is a 2 byte MSB (Most Significant Byte) word, except where otherwise
noted.
•
The carat symbol (^) notation is used to indicate mathematical "power." For example,
2^8 means 28; which is 2 x 2 x 2 x 2 x 2 x 2 x 2 x 2, which equals 256.
Data Formats
Timestamp: Stores a date from 2000 to 2099. Timestamp has a Minimum resolution of 1
second.
Byte
0
1
2
3
4
5
Value
Year
Month
Day
Hour
Minute
Second
Range
0-99 (+2000)
1-12
1-31
0-23
0-59
0-59
Mask
0x7F
0x0F
0x1F
0x1F
0x3F
0x3F
The high bits of each timestamp byte are used as flags to record meter state information
at the time of the timestamp. These bits should be masked out unless needed.
B.5.2
EPM7000 Meter Logs
The EPM7000 meter has 6 logs: System Event, Alarm (Limits), 3 Historical, and I/O
Change. Each log is described below.
1.
Note
Byte
0
1
2
Value
timestamp
3
4
5
System Event (0): The System Event log is used to store events which happen
in, and to, the meter. Events include Startup, Reset Commands, Log Retrievals,
etc. The System Event Log Record takes 20 bytes, 14 bytes of which are
available when the log is retrieved.
6
7
8
9
10
11
12
13
Group
Event
Mod
Chan
Param1
Param2
Param3
Param4
The complete Systems Events table is shown in Section B.5.5, step 1, on page B-19.
2.
Alarm Log (1): The Alarm Log records the states of the 8 Limits programmed in
the meter.
•
Whenever a limit goes out (above or below), a record is stored with the
value that caused the limit to go out.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–5
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
•
Whenever a limit returns within limit, a record is stored with the "most
out of limit" value for that limit while it was out of limit.
The Alarm Log Record uses 16 bytes, 10 bytes of which are available when the log is
retrieved.
Byte
0
1
2
Value
timestamp
3
4
5
6
7
8
9
direction
limit#
Value%
The limit # byte is broken into a type and an ID.
3.
Bit
0
1
2
3
4
5
6
Value
type
0
0
0
0
Limit ID
7
Historical Log 1 (2): The Historical Log records the values of its assigned
registers at the programmed interval.
See Section B.5.3, Number 1, for details on programming and interpreting the log.
Note
Byte
0
1
2
Value
timestamp
3
4
5
6
-
-
N
values . . .
4.
Historical Log 2 (3): Same as Historical Log 1.
5.
Historical Log 3 (4): Same as Historical Log 1.
6.
I/O Change Log (5): The I/O Change Log records changes in the input and
output of Digital I/O Type Option Cards (Relay and Pulse).
:
Table B–1: I/O Change Log tables
Byte
0
1
2
Value
Timestamp
3
4
5
6
7
8
9
Card 1 Changes
Card 1 States
Card 2 Changes
Card 2 States
:
Table B–2: Card Change Flags
B–6
Bit
7
6
5
4
3
2
1
0
Value
Out 4
Change
Out 3
Change
Out 2
Change
Out 1
Change
In 4
Change
In 3
Change
In 2
Change
In 1
Change
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
:
Table B–3: Card Current States
B.5.3
Bit
7
6
5
4
3
2
1
0
Value
Out 4
State
Out 3
State
Out 2
State
Out 1
State
In 4
State
In 3
State
In 2
State
In 1
State
Block Definitions
This section describes the Modbus Registers involved in retrieving and interpreting a
EPM7000 Meter Log. Other sections refer to certain 'values' contained in this section. See
the corresponding value in this section for details.
Note
•
“Register” is the Modbus Register Address in 0-based Hexadecimal notation. To
convert it to 1-based decimal notation, convert from hex16 to decimal10 and add 1.
For example: 0x03E7 = 1000.
•
“Size” is the number of Modbus Registers (2 byte) in a block of data.
Historical Log Programmable Settings:
The Historical Logs are programmed using a list of Modbus Registers that will be copied
into the Historical Log record. In other words, Historical Log uses a direct copy of the
Modbus Registers to control what is recorded at the time of record capture.
To supplement this, the programmable settings for the Historical Logs contain a list of
descriptors, which group registers into items. Each item descriptor lists the data type of the
item, and the number of bytes for that item. By combining these two lists, the Historical
Log record can be interpreted.
For example: Registers 0x03E7 and 0x03E8 are programmed to be recorded by the
historical log. The matching descriptor gives the data type as float, and the size as 4 bytes.
These registers program the log to record "Primary Readings Volts A-N."
Historical Log Blocks:
Start Register:
0x7917 (Historical Log 1)
0x79D7 (Historical Log 2)
0x7A97 (Historical Log 3)
Block Size:
192 registers per log (384 bytes)
The Historical Log programmable settings are comprised of 3 blocks, one for each log.
Each is identical to the others, so only Historical Log 1 is described here. All register
addresses in this section are given as the Historical Log 1 address (0x7917).
Each Historical Log Block is composed of 3 sections: The header, the list of registers to
log, and the list of item descriptors.
Header:
Registers:
0x7917 - 0x7918
Size:
2 registers
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–7
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Byte
0
1
2
Value
# Registers
# Sectors
3
Interval
• # Registers: The number of registers to log in the record. The size of the record in
memory is [12 + (# Registers x 2)]. The size during normal log retrieval is [6 + (#
Registers x 2)]. If this value is 0, the log is disabled. Valid values are {0-117}.
• # Sectors: The number of Flash Sectors allocated to this log. Each sector is 64kb,
minus a sector header of 20 bytes. 15 sectors are available for allocation between
Historical Logs 1, 2, and 3. The sum of all Historical Logs may be less than 15. If this
value is 0, the log is disabled. Valid values are {0-15}.
• Interval: The interval at which the Historical Log's Records are captured. This value
is an enumeration:
0x01
1 minute
0x02
3 minute
0x04
5 minute
0x08
10 minute
0x10
15 minute
0x20
30 minute
0x40
60 minute
0x80
End of Interval (EOI) Pulse*
* Setting the interval to EOI causes a record to be logged whenever an EOI
pulse event is generated. This is most commonly used in conjunction with
the Digital I/O Option Cards.
Note
The interval between records will not be even (fixed), and thus should not be used with
programs that expect a fixed interval.
Register List:
Registers:
0x7919 - 0x798D
Size:
1 register per list item, 117 list items
The Register List controls what Modbus Registers are recorded in each record of the
Historical Log. Since many items, such as Voltage, Energy, etc., take up more than 1
register, multiple registers need to be listed to record those items.
For example: Registers 0x03E7 and 0x03E8 are programmed to be recorded by the
historical log. These registers program the log to record "Primary Readings Volts A-N."
• Each unused register item should be set to 0x0000 or 0xFFFF to indicate that it
should be ignored.
• The actual size of the record, and the number of items in the register list which are
used, is determined by the # registers in the header.
• Each register item is the Modbus Address in the range of 0x0000 to 0xFFFF.
B–8
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Item Descriptor List:
Registers:
0x798E - 0x79C8
Size:
1 byte per item, 117 bytes (59 registers)
While the Register List describes what to log, the Item Descriptor List describes how to
interpret that information. Each descriptor describes a group of register items, and what
they mean.
Each descriptor is composed of 2 parts:
• Type: The data type of this descriptor, such as signed integer, IEEE floating point,
etc. This is the high nibble of the descriptor byte, with a value in the range of 0-14.
If this value is 0xFF, the descriptor should be ignored.
0
ASCII: An ASCII string, or byte array
1
Bitmap: A collection of bit flags
2
Signed Integer: A 2's Complement integer
3
Float: An IEEE floating point
4
Energy: Special Signed Integer, where the
value is adjusted by the energy settings in
the meter's Programmable Settings.
5
Unsigned Integer
6
Signed Integer 0.1 scale: Special Signed
Integer, where the value is divided by 10 to
give a 0.1 scale.
7-14
Unused
15
Disabled: used as end list marker.
• Size: The size in bytes of the item described. This number is used to determine the
pairing of descriptors with register items.
For example: If the first descriptor is 4 bytes, and the second descriptor is 2 bytes, then the
first 2 register items belong to the 1st descriptor, and the 3rd register item belongs to the
2nd descriptor.
Note
Note
As can be seen from the example, above, there is not a 1-to-1 relation between the register
list and the descriptor list. A single descriptor may refer to multiple register items.
Register Items
Descriptors
0x03C7/
0x03C8
0x1234
Float, 4 byte
Signed Int, 2 byte
The sum of all descriptor sizes must equal the number of bytes in the data portion of the
Historical Log record.
Log Status Block:
The Log Status Block describes the current status of the log in question. There is one
header block for each of the logs. Each log's header has the following base address:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–9
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Log
Base Address
Alarms:
0xC737
System:
0xC747
Historical 1:
0xC757
Historical 2:
0xC767
Historical 3:
0xC777
I/O Change:
0xC787
Bytes
Value
Type
Range
# Bytes
0-3
Max Records
UINT32
0 to 4,294,967,294
4
4-7
Number of Records Used
UINT32
1 to 4,294,967,294
4
8-9
Record Size in Bytes
UINT16
4 to 250
2
10-11
Log Availability
UINT16
12-17
Timestamp, First Record
TSTAMP
1Jan2000 - 31Dec2099
6
18-23
Timestamp, Last Record
TSTAMP
1Jan2000 - 31Dec2099
6
24-31
Reserved
2
8
• Max Records: The maximum number of records the log can hold given the record
size, and sector allocation. The data type is an unsigned integer from 0 to 2^32.
• Records Used: The number of records stored in the log. This number will equal the
Max Records when the log has filled. This value will be set to 1 when the log is
reset. The data type is an unsigned integer from 1 to 2^32.
Note
The first record in every log before it has rolled over is a "dummy" record, filled with all
0xFF's. When the log is filled and rolls over, this record is overwritten.
• Record Size: The number of bytes in this record, including the timestamp. The data
type is an unsigned integer in the range of 14 to 242.
• Log Availability: A flag indicating if the log is available for retrieval, or if it is in use
by another port.
B–10
0
Log Available for retrieval
1
In use by COM1 (IrDA)
2
In use by COM2 (RS485)
3
In use by COM3 (Option Card 1)
4
In use by COM4 (Option Card 2)
0xFFFF
Log Not Available - the log cannot
be retrieved. This indicates that the
log is disabled.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Note
To query the port by which you are currently connected, use the Port ID register:
Register:
0x1193
Size:
1 register
Description: A value from 1-4, which enumerates the port that the requestor is
currently connected on.
Note
• When Log Retrieval is engaged, the Log Availability value will be set to the port that
engaged the log. The Log Availability value will stay the same until either the log
has been disengaged, or 5 minutes have passed with no activity. It will then reset
to 0 (available).
•
Each log can only be retrieved by one port at a time.
•
Only one log at a time can be retrieved.
•
First Timestamp: Timestamp of the oldest record.
•
Last Timestamp: Timestamp of the newest record.
Log Retrieval Block:
The Log Retrieval Block is the main interface for retrieving logs. It is comprised of 2
parts: the header and the window. The header is used to program the particular data
the meter presents when a log window is requested. The window is a sliding block of
data that can be used to access any record in the specified log.
Session Com Port:
The EPM7000 meter's Com Port which is currently retrieving logs. Only one Com Port
can retrieve logs at any one time.
Registers:
0xC34E - 0xC34E
Size:
1 register
0
No Session Active
1
COM1 (IrDA)
2
COM2 (RS-485)
3
Option Card 1)
COM3 (Communications Capable
4
Option Card 2)
COM4 (Communications Capable
To get the current Com Port, see the NOTE on querying the port, on the previous page.
Log Retrieval Header:
The Log Retrieval Header is used to program the log to be retrieved, the record(s) of
that log to be accessed, and other settings concerning the log retrieval.
Registers:
0xC34F - 0xC350
Size:
2 registers
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–11
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Bytes
Value
Type
0-1
Log Number,
Enable, Scope
UINT16
nnnnnnnn esssssss
nnnnnnnn - log to
retrieve,
e - retrieval
session enable
sssssss - retrieval
mode
2
2-3
Records per
Window,
Number of
Repeats
UINT16
wwwwwwww nnnnnnnn
wwwwwwww records per
window,
nnnnnnnn repeat count
2
•
Format
Description
# Bytes
Log Number: The log to be retrieved. Write this value to set which log is being
retrieved.
0
System Events
1
Alarms
2
Historical Log 1
3
Historical Log 2
4
Historical Log 3
5
I/O Change Log
• Enable: This value sets if a log retrieval session is engaged (locked for retrieval) or
disengaged (unlocked, read for another to engage). Write this value with 1(enable)
to begin log retrieval. Write this value with 0(disable) to end log retrieval.
0
Disable
1
Enable
• Scope: Sets the amount of data to be retrieved for each record. The default should
be 0 (normal).
0
Normal
1
Timestamp Only
2
Image
•
Normal [0]: The default record. Contains a 6-byte timestamp at the
beginning, then N data bytes for the record data.
•
Timestamp [1]: The record only contains the 6-byte timestamp. This is
most useful to determine a range of available data for non-interval
based logs, such as Alarms and System Events.
•
Image [2]: The full record, as it is stored in memory. Contains a 2-byte
checksum, 4-byte sequence number, 6-byte timestamp, and then N data
bytes for the record data.
• Records Per Window: The number of records that fit evenly into a window. This
value is set-able, as less than a full window may be used. This number tells the
retrieving program how many records to expect to find in the window.
(RecPerWindow x RecSize) = #bytes used in the window.
B–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
This value should be ((123 x 2) \ recSize), rounded down.
For example, with a record size of 30, the RecPerWindow = ((123 x 2) \ 30) = 8.2 ~= 8
• Number of Repeats: Specifies the number of repeats to use for the Modbus
Function Code 0x23 (35). Since the meter must pre-build the response to each log
window request, this value must be set once, and each request must use the same
repeat count. Upon reading the last register in the specified window, the record
index will increment by the number of repeats, if auto-increment is enabled.
Section B.5.4.2 has additional information on Function Code 0x23.
Bytes
0
windoDisables auto-increment
1
No Repeat count, each request will
only get 1 w.
2-8
2-8 windows returned for each
Function Code 0x23 request.
Value
Type
Format
Description
0-3
Offset of
First Record
in Window
UINT32
ssssssss nnnnnnnn nnnnnnnn nnnnnnnn
ssssssss window status
nn…nn - 24-bit
record index
number.
4-249
Log Retrieve
Window
UINT16
# Bytes
4
246
Log Retrieval Window Block:
The Log Retrieval Window block is used to program the data you want to retrieve from
the log. It also provides the interface used to retrieve that data.
Registers:
0xC351 - 0xC3CD
Size:
125 registers
• Window Status: The status of the current window. Since the time to prepare a
window may exceed an acceptable modbus delay (1 second), this acts as a state
flag, signifying when the window is ready for retrieval. When this value indicates
that the window is not ready, the data in the window should be ignored. Window
Status is Read-only, any writes are ignored.
0
Window is Ready
0xFF
Window is Not Ready
• Record Number: The record number of the first record in the data window. Setting
this value controls which records will be available in the data window.
Note
•
When the log is engaged, the first (oldest) record is "latched." This means
that record number 0 will always point to the oldest record at the time of
latching, until the log is disengaged (unlocked).
•
To retrieve the entire log using auto-increment, set this value to 0, and
retrieve the window repeatedly, until all records have been retrieved.
• When auto-increment is enabled, this value will automatically increment so that
the window will "page" through the records, increasing by RecordsPerWindow
each time that the last register in the window is read.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–13
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
• When auto-increment is not enabled, this value must be written-to manually, for
each window to be retrieved.
• Log Retrieval Data Window: The actual data of the records, arranged according to
the above settings.
B.5.4
Log Retrieval
Log Retrieval is accomplished in 3 basic steps:
1.
Engage the log.
2.
Retrieve each of the records.
3.
Disengage the log.
B.5.4.1 Auto-Increment
In the traditional Modbus retrieval system, you write the index of the block of data to
retrieve, then read that data from a buffer (window). To improve the speed of retrieval,
the index can be automatically incremented each time the buffer is read.
In the EPM7000 meter, when the last register in the data window is read, the record
index is incremented by the Records per Window.
B.5.4.2 Modbus Function Code 0x23
QUERY
Field Name
Example (Hex)
Slave Address
01
Function
23
Starting Address Hi
C3
Starting Address Lo
51
# Points Hi
00
# Points Lo
7D
Repeat Count
04
Function Code 0x23 is a user defined Modbus function code, which has a format
similar to Function Code 0x03, except for the inclusion of a "repeat count." The repeat
count (RC) is used to indicate that the same N registers should be read RC number of
times. (See the Number of Repeats bullet on page B-14.)
Note
• By itself this feature would not provide any advantage, as the same data will be
returned RC times. However, when used with auto-incrementing, this function
condenses up to 8 requests into 1 request, which decreases communication time,
as fewer transactions are being made.
• In the EPM7000 meter repeat counts are limited to 8 times for Modbus RTU, and 4
times for Modbus ASCII.
The response for Function Code 0x23 is the same as for Function Code 0x03, with the
data blocks in sequence.
B–14
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Note
Before using function code 0x23, always check to see if the current connection
supports it. Some relay devices do not support user defined function codes; if that is the
case, the message will stall. Other devices don't support 8 repeat counts.
B.5.4.3 Log Retrieval Procedure
The following procedure documents how to retrieve a single log from the oldest record to
the newest record, using the "normal" record type (see Scope). All logs are retrieved using
the same method. See Section B.5.4.4 for a Log Retrieval example.
• This example uses auto-increment.
Note
• In this example, Function Code 0x23 is not used.
• You will find referenced topics in Section B.5.3. Block Definitions.
• Modbus Register numbers are listed in brackets.
1.
Engage the Log:
• Read the Log Status Block.
•
Read the contents of the specific logs' status block [0xC737+, 16 reg]
(see Log Headers).
•
Store the # of Records Used, the Record Size, and the Log
Availability.
•
If the Log Availability is not 0, stop Log Retrieval; this log is not
available at this time. If Log Availability is 0, proceed to step 1b
(Engage the log).
This step is done to ensure that the log is available for retrieval, as well as
retrieving information for later use.
• Engage the log: write log to engage to Log Number, 1 to Enable, and the desired
mode to Scope (default 0 (Normal)) [0xC34F, 1 reg]. This is best done as a singleregister write.
This step will latch the first (oldest) record to index 0, and lock the log so that only
this port can retrieve the log, until it is disengaged.
• Verify the log is engaged: read the contents of the specific logs' status block
[0xC737+, 16 reg] again to see if the log is engaged for the current port (see Log
Availability). If the Log is not engaged for the current port, repeat step 1b (Engage
the log).
• Write the retrieval information.
•
Compute the number of records per window, as follows:
RecordsPerWindow = (246 \ RecordSize)
•
If using 0x23, set the repeat count to 2-8. Otherwise, set it to 1.
•
Since we are starting from the beginning for retrieval, the first
record index is 0.
• Write the Records per window, the Number of repeats (1), and Record Index (0)
[0xC350, 3 reg].
This step tells the EPM7000 meter what data to return in the window.
2.
Retrieve the records:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–15
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
• Read the record index and window: read the record index, and the data window
[0xC351, 125 reg].
Note
•
If the meter Returns a Slave Busy Exception, repeat the request.
•
If the Window Status is 0xFF, repeat the request.
•
If the Window Status is 0, go to step 2b (Verify record index).
•
We read the index and window in 1 request to minimize communication time, and to
ensure that the record index matches the data in the data window returned.
•
Space in the window after the last specified record (RecordSize x RecordPerWindow) is
padded with 0xFF, and can be safely discarded.
• Verify that the record index incremented by Records Per Window. The record index
of the retrieved window is the index of the first record in the window. This value will
increase by Records Per Window each time the window is read, so it should be 0, N,
N x 2, N x 3. . . for each window retrieved.
•
If the record index matches the expected record index, go to step 2c
(Compute next expected record index).
•
If the record index does not match the expected record index, then go to
step 1d (Write the retrieval information), where the record index will be
the same as the expected record index. This will tell the EPM7000 meter
to repeat the records you were expecting.
• Compute next Expected Record Index.
3.
•
If there are no remaining records after the current record window, go to
step 3 (Disengage the log).
•
Compute the next expected record index by adding Records Per
Window, to the current expected record index. If this value is greater
than the number of records, re-size the window so it only contains the
remaining records and go to step 1d (Write the retrieval information),
where the Records Per Window will be the same as the remaining
records.
Disengage the log: write the Log Number (of log being disengaged) to the Log Index
and 0 to the Enable bit [0xC34F, 1 reg].
B.5.4.4 Log Retrieval Example
The following example illustrates a log retrieval session. The example makes the
following assumptions:
• Log Retrieved is Historical Log 1 (Log Index 2).
• Auto-Incrementing is used.
• Function Code 0x23 is not used (Repeat Count of 1).
• The Log contains Volts-AN, Volts-BN, Volts-CN (12 bytes).
• 100 Records are available (0-99).
• COM Port 2 (RS485) is being used (see Log Availability).
• There are no Errors.
• Retrieval is starting at Record Index 0 (oldest record).
• Protocol used is Modbus RTU. The checksum is left off for simplicity.
B–16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
• The EPM7000 meter is at device address 1.
• No new records are recorded to the log during the log retrieval process.
1.
Read [0xC757, 16 reg], Historical Log 1 Header Block.
Send:
0103 C757 0010
Command:
Register Address:
0xC757
# Registers:
16
--------------------------------------------------Receive:
0000
010320 00000100 00000064 0012
060717101511 060718101511
0000000000000000
Data:
Note
Max Records:
0x100 = 256 records maximum.
Num Records:
0x64 = 100 records currently
logged.
Record Size:
0x12 = 18 bytes per record.
Log Availability:
0x00 = 0, not in use, available for
retrieval.
First Timestamp:
0x060717101511 = July 23, 2006,
16:21:17
Last Timestamp:
0x060717101511 = July 24, 2006,
16:21:17
This indicates that Historical Log 1 is available for retrieval.
2.
Write 0x0280 -> [0xC34F, 1 reg], Log Enable.
Send:
0106 C34F 0280
Command:
Register Address:
0xC34F
# Registers:
1 (Write Single Register Command)
Data:
Log Number:
2 (Historical Log 1)
Enable:
1 (Engage log)
Scope:
0 (Normal Mode)
--------------------------------------------------Receive:
Note
0106C34F0280 (echo)
This engages the log for use on this COM Port, and latches the oldest record as record
index 0.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–17
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
3.
Read [0xC757, 16 reg], Availability is 0.
Send:
0103 C757 0010
Command:
Register Address:
0xC757
# Registers:
16
--------------------------------------------------Receive:
0002
010320 00000100 00000064 0012
060717101511 060718101511
0000000000000000
Data:
Max Records:
0x100 = 256 records maximum.
Num Records:
0x64 = 100 records currently
logged.
Record Size:
0x12 = 18 bytes per record.
Log Availability:
0x02 = 2, In use by COM2, RS485
(the current port)
0x060717101511 = July 23, 2006,
16:21:17
First Timestamp:
Last Timestamp:
Note
0x060717101511 = July 24, 2006,
16:21:17
This indicates that the log has been engaged properly in step 2. Proceed to retrieve
the log.
4.
Compute #RecPerWin as (246\18)=13. Write 0x0D01 0000 0000 -> [0xC350, 3
reg] Write Retrieval Info. Set Current Index as 0.
Send:
000000
0110 C350 0003 06 0D01 00
Command:
Register Address:
0xC350
# Registers:
3, 6 bytes
Data:
B–18
Records per Window:
13. Since the window is 246 bytes,
and the record is 18 bytes, 246\18 =
13.66, which means that 13 records
evenly fit into a single window. This
is 234 bytes, which means later on,
we only need to read 234 bytes (117
registers) of the window to retrieve
the records.
# of Repeats:
1. We are using auto-increment (so
not 0), but not function code 0x23.
Window Status:
0 (ignore)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Record Index:
0, start at the first record.
---------------------------------------------------Receive:
Note
0110C3500003 (command ok)
• This sets up the window for retrieval; now we can start retrieving the records.
• As noted above, we compute the records per window as 246\18 = 13.66, which is
rounded to 13 records per window. This allows the minimum number of requests to
be made to the meter, which increases retrieval speed.
5.
Read [0xC351, 125 reg], first 2 reg is status/index, last 123 reg is window
data. Status OK.
Send:
0103 C351 007D
Command:
Register Address:
0xC351
# Registers:
0x7D, 125 registers
--------------------------------------------------Receive:
0103FA 00000000
060717101511FFFFFFFFFFFFFFFFF
FFFFFFF
06071710160042FAAACF42FAAD18
42FAA9A8 . . .
Data:
Window Status:
0x00 = the window is ready.
Index:
0x00 = 0, The window starts with
the 0'th record, which is the oldest
record.
Record 0:
The next 18 bytes is the 0'th record
(filler).
Timestamp:
0x060717101511, = July 23, 2006,
16:21:17
Data:
This record is the "filler" record. It is
used by the meter so that there is
never 0 records. It should be
ignored. It can be identified by the
data being all 0xFF.
NOTE: Once a log has rolled over,
the 0'th record will be a valid record,
and the filler record will disappear.
Record 1:
The next 18 bytes is the 1'st record.
Timestamp:
0x060717101600 July 23, 2006,
16:22:00
Data:
Volts AN:
0x42FAAACF, float = 125.33~
Volts BN:
0x42FAAD18, float = 125.33~
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–19
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Volts CN:
0x42FAA9A8, float = 125.33~
. . .13 records
Note
• This retrieves the actual window. Repeat this command as many times as
necessary to retrieve all of the records when auto-increment is enabled.
• Note the filler record. When a log is reset (cleared) in the meter, the meter always
adds a first "filler" record, so that there is always at least 1 record in the log. This
"filler" record can be identified by the data being all 0xFF, and it being index 0. If a
record has all 0xFF for data, the timestamp is valid, and the index is NOT 0, then the
record is legitimate.
• When the "filler" record is logged, its timestamp may not be "on the interval." The
next record taken will be on the next "proper interval," adjusted to the hour. For
example, if the interval is 1 minute, the first "real" record will be taken on the next
minute (no seconds). If the interval is 15 minutes, the next record will be taken at
:15, :30, :45, or :00 - whichever of those values is next in sequence.
6.
Note
Compare the index with Current Index.
• The Current Index is 0 at this point, and the record index retrieved in step 5 is 0:
thus we go to step 8.
• If the Current Index and the record index do not match, go to step 7. The data that
was received in the window may be invalid, and should be discarded.
7.
Write the Current Index to [0xC351, 2 reg].
Send:
0110 C351 0002 04 00 00000D
Command:
Register Address:
0xC351
# Registers:
2, 4 bytes
Data:
Window Status:
0 (ignore)
Record Index:
0x0D = 13, start at the 14th record.
---------------------------------------------------Receive:
Note
0110C3510002 (command ok)
• This step manually sets the record index, and is primarily used when an out-oforder record index is returned on a read (step 6).
• The example assumes that the second window retrieval failed somehow, and we
need to recover by requesting the records starting at index 13 again.
B–20
8.
For each record in the retrieved window, copy and save the data for later
interpretation.
9.
Increment Current Index by RecordsPerWindow.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Note
• This is the step that determines how much more of the log we need to retrieve.
• On the first N passes, Records Per Window should be 13 (as computed in step 4),
and the current index should be a multiple of that (0, 13, 26, . . .). This amount will
decrease when we reach the end (see step 10).
• If the current index is greater than or equal to the number of records (in this case
100), then all records have been retrieved; go to step 12. Otherwise, go to step 10
to check if we are nearing the end of the records.
10. If number records - current index < RecordsPerWindow, decrease to match.
Note
• Here we bounds-check the current index, so we don't exceed the records available.
• If the number of remaining records (#records - current index) is less than the
Records per Window, then the next window is the last, and contains less than a full
window of records. Make records per window equal to remaining records
(#records-current index). In this example, this occurs when current index is 91 (the
8'th window). There are now 9 records available (100-91), so make Records per
Window equal 9.
11. Repeat steps 5 through 10.
Note
Go back to step 5, where a couple of values have changed.
Pass CurIndex FirstRecIndex RecPerWindow
0
0
0
13
1
13
13
13
2
26
26
13
3
39
39
13
4
52
52
13
5
65
65
13
6
78
78
13
7
91
91
9
8
100
------
-------
• At pass 8, since Current Index is equal to the number of records (100), log retrieval
should stop; go to step 12 (see step 9 Notes).
12. No more records available, clean up.
13. Write 0x0000 -> [0xC34F, 1 reg], disengage the log.
Send:
0106 C34F 0000
Command:
Register Address:
0xC34F
# Registers:
1 (Write Single Register Command)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–21
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Data:
Log Number:
0 (ignore)
Enable:
0 (Disengage log)
Scope:
0 (ignore)
---------------------------------------------------Receive:
0106C34F0000 (echo)
• This disengages the log, allowing it to be retrieved by other COM ports.
Note
• The log will automatically disengage if no log retrieval action is taken for 5 minutes.
B.5.5
Log Record Interpretation
The records of each log are composed of a 6 byte timestamp, and N data. The content
of the data portion depends on the log.
System Event Record:
Byte
0
1
2
Value
timestamp
3
4
5
6
7
8
9
10
11
12
13
Group
Event
Mod
Chan
Param1
Param2
Param3
Param4
Size: 14 bytes (20 bytes image).
Data: The System Event data is 8 bytes; each byte is an enumerated value.
•
Group: Group of the event.
•
Event: Event within a group.
•
Modifier: Additional information about the event, such as number of
sectors or log number.
•
Channel: The port of the EPM7000 meter that caused the event.
0
Firmware
1
COM 1 (IrDA)
2
COM 2 (RS485)
3
COM 3 (Option Card 1)
4
COM 4 (Option Card 2)
7
User (Face Plate)
Param 1-4: These are defined for each event (see table below).
B–22
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
The System Log Record is 20 bytes, consisting of the Record Header (12 bytes) and Payload
(8 bytes). The Timestamp (6 bytes) is in the header. Typically, software will retrieve only the
timestamp and payload, yielding a 14-byte record. The table below shows all defined
payloads.
Note
Group
(Event
group)
Event
(Event
within
group)
Mod (Event
modifier)
Channel
(1-4 for
COMs, 7
for USER, 0
for FW)
Parm1
Parm2
Parm3
Parm4
0
Comments
Startup
0
0
0
FW version
1
slot#
0
class ID
Meter Run
Firmware
Startup
card
status
0xFF
0xFF
1
Option Card
Using Default
Settings
Log Activity
1
log#
1-4
0xFF
0xFF
0xFF
0xFF
Reset
2
log#
1-4
0xFF
0xFF
0xFF
0xFF
Log Retrieval
Begin
3
log#
0-4
0xFF
0xFF
0xFF
0xFF
Log Retrieval
End
2
Clock Activity
1
0
1-4
0xFF
0xFF
0xFF
0xFF
Clock Changed
2
0
0
0xFF
0xFF
0xFF
0xFF
Daylight Time
On
3
0
0
0xFF
0xFF
0xFF
0xFF
Daylight Time
Off
3
System Resets
1
0
0-4, 7
0xFF
0xFF
0xFF
0xFF
Max & Min Reset
2
0
0-4, 7
0xFF
0xFF
0xFF
0xFF
Energy Reset
3
slot#
0-4
1 (inputs)
or 2
(outputs)
0xFF
0xFF
0xFF
Accumulators
Reset
4
Settings
Activity
1
0
1-4, 7
0xFF
0xFF
0xFF
0xFF
Password
Changed
2
0
1-4
0xFF
0xFF
0xFF
0xFF
Software Option
Changed
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–23
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
3
0
1-4, 7
0xFF
0xFF
0xFF
0xFF
Programmable
Settings
Changed
4
0
1-4, 7
0xFF
0xFF
0xFF
0xFF
Measurement
Stopped
5
Boot Activity
1
0
1-4
FW version
Exit to Boot
6
Error Reporting
& Recovery
4
log #
0
0xFF
0xFF
0xFF
0xFF
Log Babbling
Detected
5
log #
0
# records
discarded
time in seconds
Babbling Log
Periodic
Summary
6
log #
0
# records
discarded
time in seconds
Log Babbling
End Detected
7
sector#
0
error count
stimulus
0xFF
Flash Sector
Error
8
0
0
0xFF
0xFF
0xFF
0xFF
Flash Error
Counters Reset
9
0
0
0xFF
0xFF
0xFF
0xFF
Flash Job Queue
Overflow
1
sector#
0
log #
0xFF
0xFF
0xFF
acquire sector
2
sector#
0
log #
0xFF
0xFF
0xFF
release sector
3
sector#
0
erase count
4
log#
0
0xFF
0x88
erase sector
0xFF
0xFF
0xFF
write log start
record
• log# values: 0 = system log, 1 = alarms log, 2-4 = historical logs 1-3, 5 = I/O change
log
• sector# values: 0-63
• slot# values: 1-2
Note
• Stimulus for a flash sector error indicates what the flash was doing when the error
occurred: 1 = acquire sector, 2 = startup, 3 = empty sector, 4 = release sector, 5 =
write data
• Flash error counters are reset to zero in the unlikely event that both copies in
EEPROM are corrupted.
• A "babbling log" is one that is saving records faster than the meter can handle long
term. Onset of babbling occurs when a log fills a flash sector in less than an hour.
B–24
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
For as long as babbling persists, a summary of records discarded is logged every
60 minutes. Normal logging resumes when there have been no new append
attempts for 30 seconds.
• Logging of diagnostic records may be suppressed via a bit in programmable
settings.
Alarm Record:
Byte
0
1
2
Value
timestamp
3
4
5
6
7
8
9
direction
limit#
Value%
Size: 10 bytes (16 bytes image)
Data: The Alarm record data is 4 bytes, and specifies which limit the event occurred
on, and the direction of the event (going out of limit, or coming back into limit).
• Direction: The direction of the alarm event: whether this record indicates the limit
going out, or coming back into limit.
1
Going out of limit
2
Coming back into limit
Bit
0
1
2
3
4
5
6
Value
type
0
0
0
0
Limit ID
7
• Limit Type: Each limit (1-8) has both an above condition and a below condition.
Limit Type indicates which of those the record represents.
0
High Limit
1
Low Limit
• Limit ID: The specific limit this record represents. A value in the range 0-7, Limit ID
represents Limits 1-8. The specific details for this limit are stored in the
programmable settings.
• Value: Depends on the Direction:
Byte
0
Value
Identifier
1
•
If the record is "Going out of limit," this is the value of the limit when the
"Out" condition occurred.
•
If the record is "Coming back into limit," this is the "worst" value of the
limit during the period of being "out": for High (above) limits, this is the
highest value during the "out" period; for Low (below) limits, this is the
lowest value during the “out" period.
2
3
Above Setpoint
4
5
Above Hyst.
6
7
Below Setpoint
8
9
Below Hyst.
Interpretation of Alarm Data:
To interpret the data from the alarm records, you need the limit data from the
Programmable Settings [0x754B, 40 registers].
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–25
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
There are 8 limits, each with an Above Setpoint, and a Below Setpoint. Each setpoint
also has a threshold (hysteresis), which is the value at which the limit returns "into"
limit after the setpoint has been exceeded. This prevents "babbling" limits, which can
be caused by the limit value fluttering over the setpoint, causing it to go in and out of
limit continuously.
• Identifier: The first modbus register of the value that is being watched by this limit.
While any modbus register is valid, only values that can have a Full Scale will be
used by the EPM7000 meter.
• Above Setpoint: The percent of the Full Scale above which the value for this limit
will be considered "out".
•
Valid in the range of -200.0% to +200.0%
•
Stored as an integer with 0.1 resolution. (Multiply % by 10 to get the
integer, divide integer by 10 to get %. For example, 105.2% = 1052.)
• Above Hysteresis: The percent of the Full Scale below which the limit will return
"into" limit, if it is out. If this value is above the Above Setpoint, this Above limit will
be disabled.
•
Valid in the range of -200.0% to +200.0%.
•
Stored as an integer with 0.1 resolution. (Multiply % by 10 to get the
integer, divide integer by 10 to get %. For example, 104.1% = 1041.)
• Below Setpoint: The percent of the Full Scale below which the value for this limit
will be considered "out".
•
Valid in the range of -200.0% to +200.0%.
•
Stored as an integer with 0.1 resolution. (Multiply % by 10 to get the
integer, divide integer by 10 to get %. For example, 93.5% = 935.)
• Below Hysteresis: The percent of the Full Scale above which the limit will return
"into" limit, if it is out. If this value is below the Below Setpoint, this Below limit will
be disabled.
Note
•
Valid in the range of -200.0% to +200.0%.
•
Stored as an integer with 0.1 resolution. (Multiply % by 10 to get the
integer, divide integer by 10 to get %. For example, 94.9% = 949.)
The Full Scale is the "nominal" value for each of the different types of readings. To compute
the Full Scale, use the following formulas:
Current
[CT Numerator] x [CT Multiplier]
Voltage
[PT Numerator] x [PT Multiplier]
Power 3-Phase (WYE)
[CT Numerator] x [CT Multiplier] x
[PT Numerator] x [PT Multiplier] x 3
Power 3-Phase (Delta)
[CT Numerator] x [CT Multiplier] x
[PT Numerator] x [PT Multiplier] x 3 x
sqrt(3)
Power Single Phase (WYE)
[CT Numerator] x [CT Multiplier] x
[PT Numerator] x [PT Multiplier]
[CT Numerator] x [CT Multiplier] x
[PT Numerator] x [PT Multiplier] x
sqrt(3)
Power Single Phase (Delta)
B–26
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Frequency (Calibrated at 60 Hz)
60
Frequency (Calibrated at 50 Hz)
50
Power Factor
1.0
THD, Harmonics
100.0%
Angles
180°
• To interpret a limit alarm fully, you need both the start and end record (for
duration).
• There are a few special conditions related to limits:
•
When the meter powers up, it detects limits from scratch. This means
that multiple "out of limit" records can be in sequence with no "into
limit" records. Cross- reference the System Events for Power Up events.
•
This also means that if a limit is "out," and it goes back in during
the power off condition, no "into limit" record will be recorded.
•
The "worst" value of the "into limit" record follows the above
restrictions; it only represents the values since power up. Any
values before the power up condition are lost.
Historical Log Record:
Byte
0
1
2
Value
timestamp
3
4
5
6
-
-
N
values . . .
Size: 6+2 x N bytes (12+2 x N bytes), where N is the number of registers stored.
Data: The Historical Log Record data is 2 x N bytes, which contains snapshots of the
values of the associated registers at the time the record was taken. Since the meter
uses specific registers to log, with no knowledge of the data it contains, the
Programmable Settings need to be used to interpret the data in the record. See
Historical Logs Programmable Settings for details.
I/O Change Record:
Table B–4: I/O Change Log tables
Byte
0
1
2
Value
Timestamp
3
4
5
6
7
8
9
Card 1 Changes
Card 1 States
Card 2 Changes
Card 2 States
Table B–5: Card Change Flags
Bit
7
6
5
4
3
2
1
0
Value
Out 4
Change
Out 3
Change
Out 2
Change
Out 1
Change
In 4
Change
In 3
Change
In 2
Change
In 1
Change
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–27
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Table B–6: Card Current States
Bit
7
6
5
4
3
2
1
0
Value
Out 4
State
Out 3
State
Out 2
State
Out 1
State
In 4
State
In 3
State
In 2
State
In 1
State
Size: 10 bytes (16 bytes)
Data: The states of the relay and digital inputs at the time of capture for both Option
cards 1 and 2. If the option card does not support I/O Change Records (no card or not
a Digital Option Card), the value will be 0.
• An I/O Change log record will be taken for each Relay and Digital Input that has
been configured in the Programmable Settings to record when its state changes.
Note
• When any one configured Relay or Digital Input changes, the values of all Relays
and Digital Inputs are recorded, even if they are not so configured.
B.5.6
Examples
Log Retrieval Section:
send: 01 03 75 40 00 08 - Meter designation
recv: 01 03 10 4D 65 74 72 65 44 65 73 69 6E 67 5F 20 20 20 20 00 00
send: :01 03 C7 57 00 10 - Historical Log 1 status block
recv: :01 03 20 00 00 05 1E 00 00 05 1E 00 2C 00 00 06 08 17 51 08
00 06 08 18 4E 39 00 00 00 00 00 00 00 00 00 00 00
send: :01 03 79 17 00 40 - Historical Log 1 PS settings
recv: :01 03 80 13 01 00 01 23 75 23 76 23 77 1F 3F 1F 40 1F 41 1F
42 1F 43 1F 44 06 0B 06 0C 06 0D 06 0E 17 75 17 76 17 77 18
67 18 68 18 69 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00
send: :01 03 79 57 00 40 - ""
recv: :01 03 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
B–28
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 62 62 62 34 34 34 44
44 62 62 62 62 62 62 00 00 00 00 00 00
send: :01 03 75 35 00 01 - Energy PS settings
recv: :01 03 02 83 31 00 00
send: :01 03 11 93 00 01 - Connected Port ID
recv: :01 03 02 00 02 00 00
send: :01 03 C7 57 00 10 - Historical Log 1 status block
recv: :01 03 20 00 00 05 1E 00 00 05 1E 00 2C 00 00 06 08 17 51 08
00 06 08 18 4E 39 00 00 00 00 00 00 00 00 00 00 00
send: :01 03 C3 4F 00 01 - Log Retrieval header
recv: :01 03 02 FF FF 00 00
send: :01 10 C3 4F 00 04 08 02 80 05 01 00 00 00 00 - Engage the log
recv: :01 10 C3 4F 00 04
send: :01 03 C7 57 00 10 - Historical Log 1 status block
recv: :01 03 20 00 00 05 1E 00 00 05 1E 00 2C 00 02 06 08 17 51 08
00 06 08 18 4E 39 00 00 00 00 00 00 00 00 00 00 00
send: :01 10 C3 51 00 02 04 00 00 00 00 - Set the retrieval index
recv: :01 10 C3 51 00 02
send: :01 03 C3 51 00 40 - Read first half of window
recv: :01 03 80 00 00 00 00 06 08 17 51 08 00 00 19 00 2F 27 0F 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03
E8 00 01 00 05 00 00 00 00 00 00 06 08 17 51 09 00 00 19 00
2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 03 E8 00 01 00 04 00 00 00 00 00 00 06 08 17 51 0A
00 00 19 00 2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 E8 00 00 00 00
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–29
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
send: :01 03 C3 91 00 30 - Read second half of window
recv: :01 03 60 00 05 00 00 00 00 00 00 06 08 17 51 0B 00 00 19 00
2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 03 E8 00 01 00 04 00 00 00 00 00 00 06 08 17 51 0C
00 00 19 00 2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 E8 00 01 00 04 00 00 00 00 00 00 00
00
send: :01 03 C3 51 00 40 - Read first half of last window
recv: :01 03 80 00 00 05 19 06 08 18 4E 35 00 00 19 00 2F 27 0F 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03
E8 00 01 00 04 00 00 00 00 00 00 06 08 18 4E 36 00 00 19 00
2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 03 E8 00 01 00 04 00 00 00 00 00 00 06 08 18 4E 37
00 00 19 00 2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 E8 00 00 00 00
send: :01 03 C3 91 00 30 - Read second half of last window
recv: :01 03 60 00 05 00 00 00 00 00 00 06 08 18 4E 38 00 00 19 00
2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 03 E8 00 01 00 04 00 00 00 00 00 00 06 08 18 4E 39
00 00 19 00 2F 27 0F 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 E8 00 00 00 05 00 00 00 00 00 00 00
00
send: :01 06 C3 4F 00 00 - Disengage the log
recv: :01 06 C3 4F 00 00
Sample Historical Log 1 Record:
Historical Log 1 Record and Programmable Settings
13|01|00 01|23 75|23 76|23 77|1F 3F 1F 40|1F 41
1F 42|1F 43 1F 44|06 0B 06 0C|06 0D 06 0E|17 75|
17 76|17 77|18 67|18 68|18 69|00 00 . . . . . .
62 62 62 34 34 34 44 44 62 62 62 62 62 62 . . .
B–30
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
These are the Descriptions:
Item Values:
Type and Size:
13 - # registers
01 - # sectors
01 - interval
23 75
62
- (SINT 2 byte) Volts A THD Maximum
23 76
62
- (SINT 2 byte) Volts B THD Maximum
23 77
62
- (SINT 2 byte) Volts C THD Maximum
1F 3F 1F 40
34
- (Float 4 byte) Volts A Minimum
1F 41 1F 42
34
- (Float 4 byte) Volts B Minimum
1F 43 1F 44
34
- (Float 4 byte) Volts C Minimum
06 0B 06 0C
44
- (Energy 4 byte) VARhr Negative Phase A
06 0D 06 0E
44
- (Energy 4 byte) VARhr Negative Phase B
17 75
- (SINT 2 byte) Volts A 1st Harmonic
62
Magnitude
17 76
- (SINT 2 byte) Volts A 2nd Harmonic
62
Magnitude
17 77
- (SINT 2 byte) Volts A 3rd Harmonic
62
Magnitude
18 67
62
- (SINT 2 byte) Ib 3rd Harmonic Magnitude
18 68
62
- (SINT 2 byte) Ib 4th Harmonic Magnitude
18 69
62
- (SINT 2 byte) Ib 5th Harmonic Magnitude
Sample Record
06 08 17 51 08 00|00 19|00 2F|27 0F|00 00 00 00|00
00 00 00|00 00 00 00|00 00 00 00|00 00 00 00|03 E8|
00 01|00 05|00 00|00 00|00 00 . . .
11 08 17 51 08 00
- August 23, 2011 17:08:00
00 19
- 2.5%
00 2F
- 4.7%
27 0F
- 999.9% (indicates the value isn’t valid)
00 00 00 00
-0
00 00 00 00
-0
00 00 00 00
-0
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–31
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
00 00 00 00
00 00 00 00
B–32
-0
-0
03 E8
- 100.0% (Fundamental)
00 01
- 0.1%
00 05
- 0.5%
00 00
- 0.0%
00 00
- 0.0%
00 00
- 0.0%
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.6
Important Note Concerning the EPM7000 Meter's Modbus Map
In depicting Modbus Registers (Addresses), the EPM7000 meter's Modbus map uses
Holding Registers only.
B.6.1
Hex Representation
The representation shown in the table below is used by developers of Modbus drivers and
libraries, SEL 2020/2030 programmers and Firmware Developers. The EPM7000 meter's
Modbus map also uses this representation.
B.6.2
Hex
Description
0008 - 000F
Meter Serial Number
Decimal Representation
The EPM7000 meter's Modbus map defines Holding Registers as (4X) registers. Many
popular SCADA and HMI packages and their Modbus drivers have user interfaces that
require users to enter these Registers starting at 40001. So instead of entering two
separate values, one for register type and one for the actual register, they have been
combined into one number.
The EPM7000 meter's Modbus map uses a shorthand version to depict the decimal fields,
i.e., not all of the digits required for entry into the SCADA package UI are shown. For
example:
You need to display the meter's serial number in your SCADA application. The EPM7000
meter's Modbus map shows the following information for meter serial number:
Decimal
Description
9 - 16
Meter Serial Number
In order to retrieve the meter's serial number, enter 40009 into the SCADA UI as the starting
register, and 8 as the number of registers.
• In order to work with SCADA and Driver packages that use the 40001 to 49999
method for requesting holding registers, take 40000 and add the value of the
register (Address) in the decimal column of the Modbus Map. Then enter the
number (e.g., 4009) into the UI as the starting register.
• For SCADA and Driver packages that use the 400001 to 465536 method for
requesting holding registers take 400000 and add the value of the register
(Address) in the decimal column of the Modbus Map. Then enter the number (e.g.,
400009) into the UI as the starting register. The drivers for these packages strip off
the leading four and subtract 1 from the remaining value. This final value is used
as the starting register or register to be included when building the actual modbus
message.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–33
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
B.7
Modbus Register Map (MM-1 to MM-32)
Modbus Address
Hex
Decimal
Description (Note Format Range (Note
1)
6)
Units or Resolution
Comments
Option
Board
# Reg Default
Value
FIXED DATA SECTION
Identification Block
read-only
0000 - 0007 1
- 8
Meter Name
ASCII
16 char
none
8
0008 - 000F 9
- 16
ASCII
16 char
none
8
0010 - 0010 17
- 17
Meter Serial
Number
Meter Type
UINT16
bit-mapped ------st -----vvv
0011 - 0012 18
- 19
Firmware Version ASCII
4 char
none
t = transducer model (1=yes, 1
0=no),
s= submeter
model(1=yes,0=no),
vvv = Software Option:
81 = Option A,
82 = Option B,
83 = Option C,
84 = Option D,
85 = Option E ,
86 = Option F
2
0013 - 0013 20
- 20
Map Version
UINT16
0 to 65535
none
1
0014 - 0014 21
- 21
Meter
Configuration
UINT16
bit-mapped -----ccc --ffffff
0015 - 0015 22
- 22
ASIC Version
UINT16
0-65535
none
ccc = CT denominator (1 or 1
5),
ffffff = calibration frequency
(50 or 60)
1
0016 - 0017 23
- 24
ASCII
4 char
none
2
0018 - 0018 25
- 25
UINT16
0019 - 0019 26
- 26
001A - 001D 27
- 30
Boot Firmware
Version
Option Slot 1
Usage
Option Slot 2
Usage
Meter Type Name
bit-mapped same as register 10000
(0x270F)
bit-mapped same as register 11000
(0x2AF7)
8 char
none
001E - 0026 31
- 39
Reserved
Reserved
9
0027 - 002E 40
- 47
Reserved
Reserved
8
002F - 0115 48
- 278
Reserved
Reserved
231
0116 - 0130 279
- 305
Integer Readings Block occupies these registers, see below
0131 - 01F3 306
- 500
Reserved
Reserved
194
01F4 - 0203 501
- 516
Reserved
Reserved
16
B–34
UINT16
ASCII
1
1
4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
METER DATA SECTION (NOTE 2)
Readings Block ( Integer values)
read-only
0116 - 0116 279
- 279
Volts A-N
UINT16
0 to 9999
volts
0117 - 0117 280
- 280
Volts B-N
UINT16
0 to 9999
volts
0118 - 0118 281
- 281
Volts C-N
UINT16
0 to 9999
volts
0119 - 0119 282
- 282
Volts A-B
UINT16
0 to 9999
volts
011A - 011A 283
- 283
Volts B-C
UINT16
0 to 9999
volts
011B - 011B 284
- 284
Volts C-A
UINT16
0 to 9999
volts
011C - 011C 285
- 285
Amps A
UINT16
0 to 9999
amps
011D - 011D 286
- 286
Amps B
UINT16
0 to 9999
amps
011E - 011E 287
- 287
Amps C
UINT16
0 to 9999
amps
011F - 011F 288
- 288
Neutral Current
UINT16
amps
0120 - 0120 289
- 289
Watts, 3-Ph total SINT16
watts
1
0121 - 0121 290
- 290
VARs, 3-Ph total
SINT16
VARs
1
0122 - 0122 291
- 291
VAs, 3-Ph total
UINT16
-9999 to
+9999
-9999 to
+9999
-9999 to
+9999
0 to +9999
2. Per phase power and PF 1
have values
only for WYE hookup and will 1
be
zero for all other hookups.
1
3. If the reading is 10000
that means that the value is 1
out of range. Please adjust
the programmable settings 1
in that case. The display will
also show '----' in case of 1
over range.
1
VAs
1
0123 - 0123 292
- 292
1
- 293
-1000 to
+1000
0 to 9999
none
0124 - 0124 293
Power Factor, 3-Ph SINT16
total
Frequency
UINT16
Hz
1
0125 - 0125 294
- 294
Watts, Phase A
SINT16
watts
1
0126 - 0126 295
- 295
Watts, Phase B
SINT16
watts
1
0127 - 0127 296
- 296
Watts, Phase C
SINT16
watts
1
0128 - 0128 297
- 297
VARs, Phase A
SINT16
VARs
1
0129 - 0129 298
- 298
VARs, Phase B
SINT16
VARs
1
012A - 012A 299
- 299
VARs, Phase C
SINT16
VARs
1
012B - 012B 300
- 300
VAs, Phase A
UINT16
-9999 M to
+9999
-9999 M to
+9999
-9999 M to
+9999
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
0 to +9999
VAs
1
012C - 012C 301
- 301
VAs, Phase B
UINT16
0 to +9999
VAs
1
012D - 012D 302
- 302
VAs, Phase C
UINT16
0 to +9999
VAs
1
012E - 012E 303
- 303
SINT16
1
- 304
none
1
0130 - 0130 305
- 305
-1000 to
+1000
-1000 to
+1000
-1000 to
+1000
none
012F - 012F 304
Power Factor,
Phase A
Power Factor,
Phase B
Power Factor,
Phase C
none
1
SINT16
SINT16
Primary Readings Block
1.Use the settings from
1
Programmable settings for
scale and decimal point
1
location. (see User Settings
Flags)
1
Block Size:
27
read-only
03E7 - 03E8 1000 - 1001 Volts A-N
FLOAT
0 to 9999 M volts
2
03E9 - 03EA 1002 - 1003 Volts B-N
FLOAT
0 to 9999 M volts
2
03EB - 03EC 1004 - 1005 Volts C-N
FLOAT
0 to 9999 M volts
2
03ED - 03EE 1006 - 1007 Volts A-B
FLOAT
0 to 9999 M volts
2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–35
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
03EF - 03F0 1008 - 1009 Volts B-C
FLOAT
0 to 9999 M volts
2
03F1 - 03F2 1010 - 1011 Volts C-A
FLOAT
0 to 9999 M volts
2
03F3 - 03F4 1012 - 1013 Amps A
FLOAT
0 to 9999 M amps
2
03F5 - 03F6 1014 - 1015 Amps B
FLOAT
0 to 9999 M amps
2
03F7 - 03F8 1016 - 1017 Amps C
FLOAT
0 to 9999 M amps
2
watts
2
VARs
2
VAs
2
03FF - 0400 1024 - 1025 Power Factor, 3-Ph FLOAT
total
0401 - 0402 1026 - 1027 Frequency
FLOAT
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-1.00 to
+1.00
0 to 65.00
none
2
Hz
2
0403 - 0404 1028 - 1029 Neutral Current
FLOAT
0 to 9999 M amps
0405 - 0406 1030 - 1031 Watts, Phase A
FLOAT
0407 - 0408 1032 - 1033 Watts, Phase B
FLOAT
0409 - 040A 1034 - 1035 Watts, Phase C
FLOAT
040B - 040C 1036 - 1037 VARs, Phase A
FLOAT
040D - 040E 1038 - 1039 VARs, Phase B
FLOAT
040F - 0410 1040 - 1041 VARs, Phase C
FLOAT
0411 - 0412 1042 - 1043 VAs, Phase A
FLOAT
0413 - 0414 1044 - 1045 VAs, Phase B
FLOAT
0415 - 0416 1046 - 1047 VAs, Phase C
FLOAT
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-1.00 to
+1.00
-1.00 to
+1.00
-1.00 to
+1.00
0 to 9999 M
03F9 - 03FA 1018 - 1019 Watts, 3-Ph total FLOAT
03FB - 03FC 1020 - 1021 VARs, 3-Ph total
FLOAT
03FD - 03FE 1022 - 1023 VAs, 3-Ph total
FLOAT
0417 - 0418 1048 - 1049 Power Factor,
FLOAT
Phase A
0419 - 041A 1050 - 1051 Power Factor,
FLOAT
Phase B
041B - 041C 1052 - 1053 Power Factor,
FLOAT
Phase C
041D - 041E 1054 - 1055 Symmetrical
FLOAT
Component
Magnitude, 0 Seq
041F - 0420 1056 - 1057 Symmetrical
FLOAT
Component
Magnitude, + Seq
0421 - 0422 1058 - 1059 Symmetrical
FLOAT
Component
Magnitude, - Seq
SINT16
0423 - 0423 1060 - 1060 Symmetrical
Component Phase,
0 Seq
0424 - 0424 1061 - 1061 Symmetrical
SINT16
Component Phase,
+ Seq
0425 - 0425 1062 - 1062 Symmetrical
SINT16
Component Phase,
- Seq
UINT16
0426 - 0426 1063 - 1063 Unbalance, 0
sequence
component
0427 - 0427 1064 - 1064 Unbalance, UINT16
sequence
component
0428 - 0428 1065 - 1065 Current UnbalanceUINT16
B–36
watts
2
watts
Per phase power and PF
2
have values
only for WYE hookup and will 2
be
zero for all other hookups. 2
VARs
2
VARs
2
VARs
2
VAs
2
VAs
2
VAs
2
none
2
none
2
none
2
watts
volts
0 to 9999 M volts
0 to 9999 M volts
Voltage unbalance per
IEC6100-4.30
2
Values apply only to WYE
hookup and
will be zero for all other
hookups.
2
2
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
0 to 65535
0.01%
1
0 to 65535
0.01%
1
0 to 20000
0.01%
1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Block Size:
Primary Energy Block
05DB - 05DC 1500
66
read-only
- 1501 W-hours, Received SINT32
05DD - 05DE 1502 - 1503 W-hours, DeliveredSINT32
05DF - 05E0 1504 - 1505 W-hours, Net
SINT32
05E1 - 05E2 1506 - 1507 W-hours, Total
SINT32
05E3 - 05E4 1508 - 1509 VAR-hours,
Positive
05E5 - 05E6 1510 - 1511 VAR-hours,
Negative
05E7 - 05E8 1512 - 1513 VAR-hours, Net
SINT32
SINT32
05E9 - 05EA 1514 - 1515 VAR-hours, Total
SINT32
05EB - 05EC 1516 - 1517 VA-hours, Total
SINT32
SINT32
05ED - 05EE 1518 - 1519 W-hours,
SINT32
Received, Phase A
05EF - 05F0 1520 - 1521 W-hours,
SINT32
Received, Phase B
05F1 - 05F2 1522 - 1523 W-hours,
SINT32
Received, Phase C
05F3 - 05F4 1524 - 1525 W-hours,
SINT32
Delivered, Phase A
05F5 - 05F6 1526 - 1527 W-hours,
SINT32
Delivered, Phase B
05F7 - 05F8 1528 - 1529 W-hours,
SINT32
Delivered, Phase C
05F9 - 05FA 1530 - 1531 W-hours, Net,
Phase A
05FB - 05FC 1532 - 1533 W-hours, Net,
Phase B
05FD - 05FE 1534 - 1535 W-hours, Net,
Phase C
05FF - 0600 1536 - 1537 W-hours, Total,
Phase A
0601 - 0602 1538 - 1539 W-hours, Total,
Phase B
0603 - 0604 1540 - 1541 W-hours, Total,
Phase C
0605 - 0606 1542 - 1543 VAR-hours,
Positive, Phase A
0607 - 0608 1544 - 1545 VAR-hours,
Positive, Phase B
0609 - 060A 1546 - 1547 VAR-hours,
Positive, Phase C
060B - 060C 1548 - 1549 VAR-hours,
Negative, Phase A
SINT32
SINT32
SINT32
SINT32
SINT32
SINT32
SINT32
SINT32
SINT32
SINT32
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
0 to
Wh per energy format * Wh received & delivered 2
99999999 or
always have opposite signs
0 to 99999999
* Wh received is positive for
0 to
Wh per energy format "view as load", delivered is 2
positive for "view as
99999999 or
generator"
0 to 99999999
-99999999 to Wh per energy format * 5 to 8 digits
2
99999999
0 to
Wh per energy format * decimal point implied, per 2
energy format
99999999
0 to
VARh per energy format
2
* resolution of digit before
99999999
0 to VARh per energy format decimal point = units, kilo, or 2
mega, per energy format
99999999
-99999999 to VARh per energy format
2
* see note 10
99999999
0 to
VARh per energy format
2
99999999
0 to
VAh per energy format
2
99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
-99999999 to Wh per energy format
2
99999999
-99999999 to Wh per energy format
2
99999999
-99999999 to Wh per energy format
2
99999999
0 to
Wh per energy format
2
99999999
0 to
Wh per energy format
2
99999999
0 to
Wh per energy format
2
99999999
0 to
VARh per energy format
2
99999999
0 to
VARh per energy format
2
99999999
0 to
VARh per energy format
2
99999999
0 to VARh per energy format
2
99999999
B–37
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
060D - 060E 1550 - 1551 VAR-hours,
SINT32
Negative, Phase B
0 to 99999999
VARh per energy format
Block Size:
Primary Demand Block
07CF
- 07D0 2000
2
72
read-only
- 2001 Amps A, Average FLOAT
0 to 9999 M amps
2
07D1 - 07D2 2002 - 2003 Amps B, Average FLOAT
0 to 9999 M amps
2
07D3 - 07D4 2004 - 2005 Amps C, Average FLOAT
0 to 9999 M amps
2
07D5 - 07D6 2006 - 2007 Positive Watts, 3- FLOAT
Ph, Average
07D7 - 07D8 2008 - 2009 Positive VARs, 3- FLOAT
Ph, Average
07D9 - 07DA 2010 - 2011 Negative Watts, 3- FLOAT
Ph, Average
07DB - 07DC 2012 - 2013 Negative VARs, 3- FLOAT
Ph, Average
07DD - 07DE 2014 - 2015 VAs, 3-Ph, Average FLOAT
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-1.00 to
+1.00
-1.00 to
+1.00
0 to 9999 M
watts
2
VARs
2
watts
2
VARs
2
VAs
2
none
2
none
2
amps
2
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-9999 M to
+9999 M
-1.00 to
+1.00
-1.00 to
+1.00
-1.00 to
+1.00
-1.00 to
+1.00
-1.00 to
+1.00
-1.00 to
+1.00
watts
2
watts
2
watts
2
VARs
2
VARs
2
VARs
2
watts
2
watts
2
watts
2
VARs
2
VARs
2
VARs
2
VAs
2
VAs
2
VAs
2
none
2
none
2
none
2
none
2
none
2
none
2
07DF - 07E0 2016 - 2017 Positive PF, 3-Ph, FLOAT
Average
07E1 - 07E2 2018 - 2019 Negative PF, 3-PF, FLOAT
Average
07E3 - 07E4 2020 - 2021 Neutral Current, FLOAT
Average
07E5 - 07E6 2022 - 2023 Positive Watts,
FLOAT
Phase A, Average
07E7 - 07E8 2024 - 2025 Positive Watts,
FLOAT
Phase B, Average
07E9 - 07EA 2026 - 2027 Positive Watts,
FLOAT
Phase C, Average
07EB - 07EC 2028 - 2029 Positive VARs,
FLOAT
Phase A, Average
07ED - 07EE 2030 - 2031 Positive VARs,
FLOAT
Phase B, Average
07EF - 07F0 2032 - 2033 Positive VARs,
FLOAT
Phase C, Average
07F1 - 07F2 2034 - 2035 Negative Watts, FLOAT
Phase A, Average
07F3 - 07F4 2036 - 2037 Negative Watts, FLOAT
Phase B, Average
07F5 - 07F6 2038 - 2039 Negative Watts, FLOAT
Phase C, Average
07F7 - 07F8 2040 - 2041 Negative VARs,
FLOAT
Phase A, Average
07F9 - 07FA 2042 - 2043 Negative VARs,
FLOAT
Phase B, Average
07FB - 07FC 2044 - 2045 Negative VARs,
FLOAT
Phase C, Average
07FD - 07FE 2046 - 2047 VAs, Phase A,
FLOAT
Average
07FF - 0800 2048 - 2049 VAs, Phase B,
FLOAT
Average
0801 - 0802 2050 - 2051 VAs, Phase C,
FLOAT
Average
0803 - 0804 2052 - 2053 Positive PF, Phase FLOAT
A, Average
0805 - 0806 2054 - 2055 Positive PF, Phase FLOAT
B, Average
0807 - 0808 2056 - 2057 Positive PF, Phase FLOAT
C, Average
0809 - 080A 2058 - 2059 Negative PF, Phase FLOAT
A, Average
080B - 080C 2060 - 2061 Negative PF, Phase FLOAT
B, Average
080D - 080E 2062 - 2063 Negative PF, Phase FLOAT
C, Average
B–38
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Block Size:
Uncompensated Readings Block
read-only
0BB7 - 0BB8 3000 - 3001 Watts, 3-Ph total FLOAT
0BB9 - 0BBA 3002 - 3003 VARs, 3-Ph total
FLOAT
0BBB - 0BBC 3004 - 3005 VAs, 3-Ph total
FLOAT
0BBD - 0BBE 3006 - 3007 Power Factor, 3-Ph FLOAT
total
0BBF - 0BC0 3008 - 3009 Watts, Phase A
FLOAT
0BC1 - 0BC2 3010 - 3011 Watts, Phase B
FLOAT
0BC3 - 0BC4 3012 - 3013 Watts, Phase C
FLOAT
0BC5 - 0BC6 3014 - 3015 VARs, Phase A
FLOAT
OBC7 - 0BC8 3016 - 3017 VARs, Phase B
FLOAT
0BC9 - 0BCA 3018 - 3019 VARs, Phase C
FLOAT
0BCB - 0BCC 3020 - 3021 VAs, Phase A
FLOAT
0BCD - 0BCE 3022 - 3023 VAs, Phase B
FLOAT
0BCF - 0BD0 3024 - 3025 VAs, Phase C
FLOAT
0BD1 - 0BD2 3026 - 3027 Power Factor,
FLOAT
Phase A
0BD3 - 0BD4 3028 - 3029 Power Factor,
FLOAT
Phase B
0BD5 - 0BD6 3030 - 3031 Power Factor,
FLOAT
Phase C
0BD7 - 0BD8 3032 - 3033 W-hours, Received SINT32
0BD9 - 0BDA 3034 - 3035 W-hours, DeliveredSINT32
0BDB - 0BDC 3036
- 3037 W-hours, Net
64
SINT32
0BDD - 0BDE 3038 - 3039 W-hours, Total
SINT32
0BDF - 0BE0 3040 - 3041 VAR-hours,
Positive
0BE1 - 0BE2 3042 - 3043 VAR-hours,
Negative
0BE3 - 0BE4 3044 - 3045 VAR-hours, Net
SINT32
SINT32
0BE5 - 0BE6 3046 - 3047 VAR-hours, Total
SINT32
0BE7 - 0BE8 3048 - 3049 VA-hours, Total
SINT32
SINT32
0BE9 - 0BEA 3050 - 3051 W-hours,
SINT32
Received, Phase A
0BEB - 0BEC 3052 - 3053 W-hours,
SINT32
Received, Phase B
0BED - 0BEE 3054 - 3055 W-hours,
SINT32
Received, Phase C
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
-9999 M to watts
2
+9999 M
-9999 M to VARs
2
+9999 M
-9999 M to VAs
2
+9999 M
-1.00 to
none
2
+1.00
-9999 M to watts
Per phase power and PF
2
+9999 M
have values
only for WYE hookup and will 2
-9999 M to watts
be
+9999 M
zero for all other hookups. 2
-9999 M to watts
+9999 M
-9999 M to VARs
2
+9999 M
-9999 M to VARs
2
+9999 M
-9999 M to VARs
2
+9999 M
-9999 M to VAs
2
+9999 M
-9999 M to VAs
2
+9999 M
-9999 M to VAs
2
+9999 M
-1.00 to
none
2
+1.00
-1.00 to
none
2
+1.00
-1.00 to
none
2
+1.00
0 to
Wh per energy format * Wh received & delivered 2
99999999 or
always have opposite signs
0 to 99999999
* Wh received is positive for
0 to
Wh per energy format "view as load", delivered is 2
positive for "view as
99999999 or
generator"
0 to 99999999
-99999999 to Wh per energy format * 5 to 8 digits
2
99999999
0 to
Wh per energy format * decimal point implied, per 2
energy format
99999999
0 to
VARh per energy format
2
* resolution of digit before
99999999
0 to VARh per energy format decimal point = units, kilo, or 2
mega, per energy format
99999999
-99999999 to VARh per energy format
2
* see note 10
99999999
VARh per energy format
2
0 to
99999999
0 to
VAh per energy format
2
99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
0 to
Wh per energy format
2
99999999 or
0 to 99999999
B–39
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
0BEF - 0BF0 3056 - 3057 W-hours,
SINT32
Delivered, Phase A
0BF1 - 0BF2 3058 - 3059 W-hours,
SINT32
Delivered, Phase B
0BF3 - 0BF4 3060 - 3061 W-hours,
SINT32
Delivered, Phase C
0BF5 - 0BF6 3062 - 3063 W-hours, Net,
SINT32
Phase A
0BF7 - 0BF8 3064 - 3065 W-hours, Net,
SINT32
Phase B
0BF9 - 0BFA 3066 - 3067 W-hours, Net,
SINT32
Phase C
0BFB - 0BFC 3068 - 3069 W-hours, Total,
SINT32
Phase A
0BFD - 0BFE 3070 - 3071 W-hours, Total,
SINT32
Phase B
0BFF - 0C00 3072 - 3073 W-hours, Total,
SINT32
Phase C
0C01 - 0C02 3074 - 3075 VAR-hours,
SINT32
Positive, Phase A
SINT32
0C03 - 0C04 3076 - 3077 VAR-hours,
Positive, Phase B
0C05 - 0C06 3078 - 3079 VAR-hours,
SINT32
Positive, Phase C
0C07 - 0C08 3080 - 3081 VAR-hours,
SINT32
Negative, Phase A
0C09 - 0C0A 3082 - 3083 VAR-hours,
SINT32
Negative, Phase B
0C0B - 0C0C 3084 - 3085 VAR-hours,
SINT32
Negative, Phase C
0C0D - 0C0E 3086 - 3087 VAR-hours, Net, SINT32
Phase A
0C0F - 0C10 3088 - 3089 VAR-hours, Net, SINT32
Phase B
0C11 - 0C12 3090 - 3091 VAR-hours, Net, SINT32
Phase C
0C13 - 0C14 3092 - 3093 VAR-hours, Total, SINT32
Phase A
0C15 - 0C16 3094 - 3095 VAR-hours, Total, SINT32
Phase B
0C17 - 0C18 3096 - 3097 VAR-hours, Total, SINT32
Phase C
0C19 - 0C1A 3098 - 3099 VA-hours, Phase A SINT32
0C1B - 0C1C 3100 - 3101 VA-hours, Phase B SINT32
0C1D - 0C1E 3102 - 3103 VA-hours, Phase C SINT32
0 to
Wh per energy format
99999999 or
0 to 99999999
0 to
Wh per energy format
99999999 or
0 to 99999999
0 to
Wh per energy format
99999999 or
0 to 99999999
-99999999 to Wh per energy format
99999999
-99999999 to Wh per energy format
99999999
-99999999 to Wh per energy format
99999999
0 to
Wh per energy format
99999999
0 to
Wh per energy format
99999999
0 to
Wh per energy format
99999999
0 to
VARh per energy format
99999999
0 to
VARh per energy format
99999999
0 to
VARh per energy format
99999999
0 to VARh per energy format
99999999
0 to VARh per energy format
99999999
0 to VARh per energy format
99999999
-99999999 to VARh per energy format
99999999
-99999999 to VARh per energy format
99999999
-99999999 to VARh per energy format
99999999
0 to
VARh per energy format
99999999
0 to
VARh per energy format
99999999
0 to
VARh per energy format
99999999
0 to
VAh per energy format
99999999
0 to
VAh per energy format
99999999
0 to
VAh per energy format
99999999
Phase Angle Block
1003
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Block Size:
104
read-only
- 4100 Phase A Current
SINT16
1004 - 1004 4101 - 4101 Phase B Current
SINT16
1005 - 1005 4102 - 4102 Phase C Current
SINT16
1006 - 1006 4103 - 4103 Angle, Volts A-B
SINT16
1007 - 1007 4104 - 4104 Angle, Volts B-C
SINT16
1008 - 1008 4105 - 4105 Angle, Volts C-A
SINT16
B–40
- 1003 4100
2
-1800 to
+1800
-1800 to
+1800
-1800 to
+1800
-1800 to
+1800
-1800 to
+1800
-1800 to
+1800
0.1 degree
1
0.1 degree
1
0.1 degree
1
0.1 degree
1
0.1 degree
1
0.1 degree
1
Block Size:
6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Status Block
1193
- 1193 4500
read-only
- 4500 Port ID
UINT16
1 to 4
1194 - 1194 4501 - 4501 Meter Status
UINT16
bit-mapped mmmpch-- tffeeccc
1195 - 1195 4502 - 4502 Limits Status
UINT16
bit-mapped 87654321 87654321
1196 - 1197 4503 - 4504 Time Since Reset UINT32
0 to
4294967294
1198 - 119A 4505 - 4507 Meter On Time
TSTAMP 1Jan2000 31Dec2099
119B - 119D 4508 - 4510 Current Date and TSTAMP 1Jan2000 Time
31Dec2099
119E - 119E 4511 - 4511 Clock Sync Status UINT16 bit-mapped
119F - 119F 4512 - 4512 Current Day of
Week
UINT16
1 to 7
none
4 msec
1 sec
- 176F 6000
high byte is setpt 1, 0=in,
1=out
low byte is setpt 2, 0=in,
1=out
see notes 11, 12, 17
wraps around after max
count
1 sec
1
2
3
3
mmm0 0ppe 0000 000s mmm00ppe = configuration 1
per programmable settings
(see register 30011, 0x753A)
s = status: 1=working
properly, 0=not working
1 day
1=Sun, 2=Mon, etc.
1
Block Size:
THD Block (Note 13)
176F
Identifies which EPM7000 1
COM port a master is
connected to; 1 for COM1, 2
for COM2, etc.
"mmm = measurement state 1
(0=off, 1=running normally,
2=limp mode, 3=warmup,
6&7=boot, others unused)
See note 16.
pch = NVMEM block OK flags
(p=profile, c=calibration,
h=header), flag is 1 if OK
t - CT PT compensation
status.
(0=Disabled,1=Enabled)
ff = flash state (0=initializing,
1=logging disabled by
Vswitch, 3=logging)
ee = edit state (0=startup,
1=normal, 2=privileged
command session, 3=profile
update mode)
ccc = port enabled for
edit(0=none, 1-4=COM1COM4, 7=front panel)"
13
read-only
- 6000 Volts A-N, %THD
UINT16
0 to 10000
0.01%
1
1770 - 1770 6001 - 6001 Volts B-N, %THD
UINT16
0 to 10000
0.01%
1
1771 - 1771 6002 - 6002 Volts C-N, %THD
UINT16
0 to 10000
0.01%
1
1772 - 1772 6003 - 6003 Amps A, %THD
UINT16
0 to 10000
0.01%
1
1773 - 1773 6004 - 6004 Amps B, %THD
UINT16
0 to 10000
0.01%
1
1774 - 1774 6005 - 6005 Amps C, %THD
UINT16
0 to 10000
0.01%
1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–41
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
1775 - 179C 6006 - 6045 Phase A Voltage UINT16
harmonic
magnitudes
179D - 17C4 6046 - 6085 Phase A Voltage SINT16
harmonic phases
17C5 - 17EC 6086 - 6125 Phase A Current UINT16
harmonic
magnitudes
17ED - 1814 6126 - 6165 Phase A Current SINT16
harmonic phases
1815 - 183C 6166 - 6205 Phase B Voltage UINT16
harmonic
magnitudes
183D - 1864 6206 - 6245 Phase B Voltage SINT16
harmonic phases
1865 - 188C 6246 - 6285 Phase B Current UINT16
harmonic
magnitudes
188D - 18B4 6286 - 6325 Phase B Current SINT16
harmonic phases
18B5 - 18DC 6326 - 6365 Phase C Voltage UINT16
harmonic
magnitudes
18DD - 1904 6366 - 6405 Phase C Voltage SINT16
harmonic phases
1905 - 192C 6406 - 6445 Phase C Current UINT16
harmonic
magnitudes
192D - 1954 6446 - 6485 Phase C Current SINT16
harmonic phases
1955 - 1955 6486 - 6486 Wave Scope scale UINT16
factor for channel
Va
1956 - 1956 6487 - 6487 Wave Scope scale UINT16
factors for channel
Ib
1957 - 1958 6488 - 6489 Wave Scope scale UINT16
factors for
channels Vb and Ib
1959 - 195A 6490 - 6491 Wave Scope scale UINT16
factors for
channels Vc and Ic
195B - 199A 6492 - 6555 Wave Scope
SINT16
samples for
channel Va
199B - 19DA 6556 - 6619 Wave Scope
SINT16
samples for
channel Ia
19DB - 1A1A 6620 - 6683 Wave Scope
SINT16
samples for
channel Vb
1A1B - 1A5A 6684 - 6747 Wave Scope
SINT16
samples for
channel Ib
1A5B - 1A9A 6748 - 6811 Wave Scope
SINT16
samples for
channel Vc
1A9B - 1ADA 6812 - 6875 Wave Scope
SINT16
samples for
channel Ic
B–42
0 to 10000
0.01%
-1800 to
+1800
0 to 10000
0.1 degree
-1800 to
+1800
0 to 10000
-1800 to
+1800
0 to 10000
-1800 to
+1800
0 to 10000
-1800 to
+1800
0 to 10000
-1800 to
+1800
0 to 32767
0 to 32767
0 to 32767
0 to 32767
-32768 to
+32767
0.01%
0.1 degree
0.01%
0.1 degree
0.01%
In each group of 40
40
registers, the first register
represents the fundamental
frequency or first harmonic, 40
the second represents the
second harmonic, and so on 40
up to the 40th register which
represents the 40th
harmonic.
40
Harmonic magnitudes are 40
given as % of the
fundamental magnitude.
Thus the first register in
40
each group of 40 will
typically be 9999. A reading 40
of 10000 indicates invalid.
0.1 degree
40
0.01%
40
0.1 degree
40
0.01%
40
0.1 degree
40
Convert individual samples to
volts or amps:
V or A = (sample * scale factor)
/ 1,000,000
1
1
2
Samples update in
conjunction with THD and
2
harmonics; samples not
available (all zeroes) if THD not
available.
64
-32768 to
+32767
64
-32768 to
+32767
64
-32768 to
+32767
64
-32768 to
+32767
64
-32768 to
+32767
64
Block Size:
876
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Short term Primary Minimum Block
1F27
- 1F28 7976
1F29 - 1F2A 7978
1F2B - 1F2C 7980
1F2D - 1F2E 7982
1F2F - 1F30 7984
1F31 - 1F32 7986
1F33
- 1F34 7988
1F35 - 1F36 7990
1F37 - 1F38 7992
1F39 - 1F3A 7994
1F3B - 1F3C 7996
1F3D - 1F3E 7998
- 7977 Volts A-N, previous FLOAT
Demand interval
Short Term
Minimum
- 7979 Volts B-N, previous FLOAT
Demand interval
Short Term
Minimum
- 7981 Volts C-N, previous FLOAT
Demand interval
Short Term
Minimum
- 7983 Volts A-B, previous FLOAT
Demand interval
Short Term
Minimum
- 7985 Volts B-C, previous FLOAT
Demand interval
Short Term
Minimum
- 7987 Volts C-A, previous FLOAT
Demand interval
Short Term
Minimum
- 7989 Volts A-N, Short FLOAT
Term Minimum
- 7991 Volts B-N, Short FLOAT
Term Minimum
- 7993 Volts C-N, Short FLOAT
Term Minimum
- 7995 Volts A-B, Short
FLOAT
Term Minimum
- 7997 Volts B-C, Short
FLOAT
Term Minimum
- 7999 Volts C-A, Short FLOAT
Term Minimum
read-only
0 to 9999 M volts
0 to 9999 M volts
Minimum instantaneous
2
value measured during the
demand interval before the
one most recently
completed.
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
0 to 9999 M volts
Minimum instantaneous
2
value measured during the
most recently completed
2
demand interval.
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
Block Size:
Primary Minimum Block
1F3F
- 1F40 8000
1F41 - 1F42 8002
1F43 - 1F44 8004
1F45 - 1F46 8006
1F47 - 1F48 8008
1F49 - 1F4A 8010
1F4B - 1F4C 8012
1F4D - 1F4E 8014
1F4F - 1F50 8016
1F51 - 1F52 8018
1F53 - 1F54 8020
1F55 - 1F56 8022
1F57 - 1F58 8024
- 8001 Volts A-N,
FLOAT
Minimum
- 8003 Volts B-N,
FLOAT
Minimum
- 8005 Volts C-N,
FLOAT
Minimum
- 8007 Volts A-B,
FLOAT
Minimum
- 8009 Volts B-C,
FLOAT
Minimum
- 8011 Volts C-A,
FLOAT
Minimum
- 8013 Amps A, Minimum FLOAT
Avg Demand
- 8015 Amps B, Minimum FLOAT
Avg Demand
- 8017 Amps C, Minimum FLOAT
Avg Demand
- 8019 Positive Watts, 3- FLOAT
Ph, Minimum Avg
Demand
- 8021 Positive VARs, 3- FLOAT
Ph, Minimum Avg
Demand
- 8023 Negative Watts, 3- FLOAT
Ph, Minimum Avg
Demand
- 8025 Negative VARs, 3- FLOAT
Ph, Minimum Avg
Demand
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
24
read-only
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M amps
2
0 to 9999 M amps
2
0 to 9999 M amps
2
0 to +9999 M watts
2
0 to +9999 M VARs
2
0 to +9999 M watts
2
0 to +9999 M VARs
2
B–43
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
1F59 - 1F5A 8026 - 8027 VAs, 3-Ph,
FLOAT
Minimum Avg
Demand
1F5B - 1F5C 8028 - 8029 Positive Power
FLOAT
Factor, 3-Ph,
Minimum Avg
Demand
1F5D - 1F5E 8030 - 8031 Negative Power FLOAT
Factor, 3-Ph,
Minimum Avg
Demand
1F5F - 1F60 8032 - 8033 Frequency,
FLOAT
Minimum
1F61 - 1F62 8034 - 8035 Neutral Current, FLOAT
Minimum Avg
Demand
1F63 - 1F64 8036 - 8037 Positive Watts,
FLOAT
Phase A, Minimum
Avg Demand
1F65 - 1F66 8038 - 8039 Positive Watts,
FLOAT
Phase B, Minimum
Avg Demand
1F67 - 1F68 8040 - 8041 Positive Watts,
FLOAT
Phase C, Minimum
Avg Demand
1F69 - 1F6A 8042 - 8043 Positive VARs,
FLOAT
Phase A, Minimum
Avg Demand
1F6B - 1F6C 8044 - 8045 Positive VARs,
FLOAT
Phase B, Minimum
Avg Demand
1F6D - 1F6E 8046 - 8047 Positive VARs,
FLOAT
Phase C, Minimum
Avg Demand
1F6F - 1F70 8048 - 8049 Negative Watts, FLOAT
Phase A, Minimum
Avg Demand
1F71 - 1F72 8050 - 8051 Negative Watts, FLOAT
Phase B, Minimum
Avg Demand
1F73 - 1F74 8052 - 8053 Negative Watts, FLOAT
Phase C, Minimum
Avg Demand
1F75 - 1F76 8054 - 8055 Negative VARs,
FLOAT
Phase A, Minimum
Avg Demand
1F77 - 1F78 8056 - 8057 Negative VARs,
FLOAT
Phase B, Minimum
Avg Demand
1F79 - 1F7A 8058 - 8059 Negative VARs,
FLOAT
Phase C, Minimum
Avg Demand
FLOAT
1F7B - 1F7C 8060 - 8061 VAs, Phase A,
Minimum Avg
Demand
1F7D - 1F7E 8062 - 8063 VAs, Phase B,
FLOAT
Minimum Avg
Demand
1F7F - 1F80 8064 - 8065 VAs, Phase C,
FLOAT
Minimum Avg
Demand
1F81 - 1F82 8066 - 8067 Positive PF, Phase FLOAT
A, Minimum Avg
Demand
1F83 - 1F84 8068 - 8069 Positive PF, Phase FLOAT
B, Minimum Avg
Demand
1F85 - 1F86 8070 - 8071 Positive PF, Phase FLOAT
C, Minimum Avg
Demand
1F87 - 1F88 8072 - 8073 Negative PF, Phase FLOAT
A, Minimum Avg
Demand
1F89 - 1F8A 8074 - 8075 Negative PF, Phase FLOAT
B, Minimum Avg
Demand
B–44
-9999 M to
+9999 M
VAs
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
0 to 65.00
Hz
2
0 to 9999 M amps
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VAs
2
-9999 M to
+9999 M
VAs
2
-9999 M to
+9999 M
VAs
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
1F8B - 1F8C 8076 - 8077 Negative PF, Phase FLOAT
C, Minimum Avg
Demand
1F8D - 1F8D 8078 - 8078 Volts A-N, %THD, UINT16
Minimum
1F8E - 1F8E 8079 - 8079 Volts B-N, %THD, UINT16
Minimum
1F8F - 1F8F 8080 - 8080 Volts C-N, %THD, UINT16
Minimum
1F90 - 1F90 8081 - 8081 Amps A, %THD,
UINT16
Minimum
1F91 - 1F91 8082 - 8082 Amps B, %THD,
UINT16
Minimum
1F92 - 1F92 8083 - 8083 Amps C, %THD,
UINT16
Minimum
1F93 - 1F94 8084 - 8085 Symmetrical
FLOAT
Component
Magnitude, 0 Seq,
Minimum
1F95 - 1F96 8086 - 8087 Symmetrical
FLOAT
Component
Magnitude, + Seq,
Minimum
1F97 - 1F98 8088 - 8089 Symmetrical
FLOAT
Component
Magnitude, - Seq,
Minimum
1F99 - 1F99 8090 - 8090 Symmetrical
SINT16
Component Phase,
0 Seq, Minimum
1F9A - 1F9A 8091 - 8091 Symmetrical
SINT16
Component Phase,
+ Seq, Minimum
1F9B - 1F9B 8092 - 8092 Symmetrical
SINT16
Component Phase,
- Seq, Minimum
1F9C - 1F9C 8093 - 8093 Unbalance, 0
UINT16
sequence,
Minimum
1F9D - 1F9D 8094 - 8094 Unbalance, UINT16
sequence,
Minimum
1F9E - 1F9E 8095 - 8095 Current
UINT16
Unbalance,
Minimum
-1.00 to
+1.00
none
2
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
0 to 65535
0.01%
1
0 to 65535
0.01%
1
0 to 20000
0.01%
1
Block Size:
Primary Minimum Timestamp Block
20CF
- 20D1 8400
20D2 - 20D4 8403
20D5 - 20D7 8406
20D8 - 20DA 8409
20DB - 20DD 8412
20DE - 20E0 8415
20E1 - 20E3 8418
20E4 - 20E6 8421
20E7 - 20E9 8424
20EA - 20EC 8427
- 8402 Volts A-N, Min
Timestamp
- 8405 Volts B-N, Min
Timestamp
- 8408 Volts C-N, Min
Timestamp
- 8411 Volts A-B, Min
Timestamp
- 8414 Volts B-C, Min
Timestamp
- 8417 Volts C-A, Min
Timestamp
- 8420 Amps A, Min Avg
Dmd Timestamp
- 8423 Amps B, Min Avg
Dmd Timestamp
- 8426 Amps C, Min Avg
Dmd Timestamp
- 8429 Positive Watts, 3Ph, Min Avg Dmd
Timestamp
96
read-only
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
TSTAMP 1Jan2000 31Dec2099
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
B–45
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
20ED - 20EF 8430 - 8432 Positive VARs, 3- TSTAMP
Ph, Min Avg Dmd
Timestamp
20F0 - 20F2 8433 - 8435 Negative Watts, 3- TSTAMP
Ph, Min Avg Dmd
Timestamp
20F3 - 20F5 8436 - 8438 Negative VARs, 3- TSTAMP
Ph, Min Avg Dmd
Timestamp
20F6 - 20F8 8439 - 8441 VAs, 3-Ph, Min Avg TSTAMP
Dmd Timestamp
20F9 - 20FB 8442 - 8444 Positive Power
TSTAMP
Factor, 3-Ph, Min
Avg Dmd
Timestamp
20FC - 20FE 8445 - 8447 Negative Power TSTAMP
Factor, 3-Ph, Min
Avg Dmd
Timestamp
20FF - 2101 8448 - 8450 Frequency, Min
TSTAMP
Timestamp
2102 - 2104 8451 - 8453 Neutral Current, TSTAMP
Min Avg Dmd
Timestamp
2105 - 2107 8454 - 8456 Positive Watts,
TSTAMP
Phase A, Min Avg
Dmd Timestamp
TSTAMP
2108 - 210A 8457 - 8459 Positive Watts,
Phase B, Min Avg
Dmd Timestamp
210B - 210D 8460 - 8462 Positive Watts,
TSTAMP
Phase C, Min Avg
Dmd Timestamp
210E - 2110 8463 - 8465 Positive VARs,
TSTAMP
Phase A, Min Avg
Dmd Timestamp
2111 - 2113 8466 - 8468 Positive VARs,
TSTAMP
Phase B, Min Avg
Dmd Timestamp
2114 - 2116 8469 - 8471 Positive VARs,
TSTAMP
Phase C, Min Avg
Dmd Timestamp
2117 - 2119 8472 - 8474 Negative Watts, TSTAMP
Phase A, Min Avg
Dmd Timestamp
211A - 211C 8475 - 8477 Negative Watts, TSTAMP
Phase B, Min Avg
Dmd Timestamp
211D - 211F 8478 - 8480 Negative Watts, TSTAMP
Phase C, Min Avg
Dmd Timestamp
TSTAMP
2120 - 2122 8481 - 8483 Negative VARs,
Phase A, Min Avg
Dmd Timestamp
2123 - 2125 8484 - 8486 Negative VARs,
TSTAMP
Phase B, Min Avg
Dmd Timestamp
2126 - 2128 8487 - 8489 Negative VARs,
TSTAMP
Phase C, Min Avg
Dmd Timestamp
2129 - 212B 8490 - 8492 VAs, Phase A, Min TSTAMP
Avg Dmd
Timestamp
212C - 212E 8493 - 8495 VAs, Phase B, Min TSTAMP
Avg Dmd
Timestamp
212F - 2131 8496 - 8498 VAs, Phase C, Min TSTAMP
Avg Dmd
Timestamp
2132 - 2134 8499 - 8501 Positive PF, Phase TSTAMP
A, Min Avg Dmd
Timestamp
2135 - 2137 8502 - 8504 Positive PF, Phase TSTAMP
B, Min Avg Dmd
Timestamp
B–46
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2100
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
3
3
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2138 - 213A 8505 - 8507 Positive PF, Phase TSTAMP
C, Min Avg Dmd
Timestamp
213B - 213D 8508 - 8510 Negative PF, Phase TSTAMP
A, Min Avg Dmd
Timestamp
213E - 2140 8511 - 8513 Negative PF, Phase TSTAMP
B, Min Avg Dmd
Timestamp
2141 - 2143 8514 - 8516 Negative PF, Phase TSTAMP
C, Min Avg Dmd
Timestamp
2144 - 2146 8517 - 8519 Volts A-N, %THD, TSTAMP
Min Timestamp
2147 - 2149 8520 - 8522 Volts B-N, %THD, TSTAMP
Min Timestamp
214A - 214C 8523 - 8525 Volts C-N, %THD, TSTAMP
Min Timestamp
214D - 214F 8526 - 8528 Amps A, %THD,
TSTAMP
Min Timestamp
2150 - 2152 8529 - 8531 Amps B, %THD,
TSTAMP
Min Timestamp
2153 - 2155 8532 - 8534 Amps C, %THD,
TSTAMP
Min Timestamp
2156 - 2158 8535 - 8537 Symmetrical Comp TSTAMP
Magnitude, 0 Seq,
Min Timestamp
2159 - 215B 8538 - 8540 Symmetrical Comp TSTAMP
Magnitude, + Seq,
Min Timestamp
215C - 215E 8541 - 8543 Symmetrical Comp TSTAMP
Magnitude, - Seq,
Min Timestamp
215F - 2161 8544 - 8546 Symmetrical Comp TSTAMP
Phase, 0 Seq, Min
Timestamp
2162 - 2164 8547 - 8549 Symmetrical Comp TSTAMP
Phase, + Seq, Min
Timestamp
2165 - 2167 8550 - 8552 Symmetrical Comp TSTAMP
Phase, - Seq, Min
Timestamp
2168 - 2170 8553 - 8555 Unbalance, 0 Seq, TSTAMP
Min Timestamp
2171 - 2173 8556 - 8558 Unbalance, - Seq, TSTAMP
Min Timestamp
2174 - 2176 8559 - 8561 Current
TSTAMP
Unbalance, Min
Timestamp
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
3
3
3
Block Size:
162
B–47
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Short term Primary Maximum Block
230F
- 2310 8976
2311 - 2312 8978
2313 - 2314 8980
2315 - 2316 8982
2317 - 2318 8984
2319 - 231A 8986
231B
- 231C 8988
231D - 231E 8990
232F - 2320 8992
2321 - 2322 8994
2323 - 2324 8996
2325 - 2326 8998
- 8977 Volts A-N, previous FLOAT
Demand interval
Short Term
Maximum
- 8979 Volts B-N, previous FLOAT
Demand interval
Short Term
Maximum
- 8981 Volts C-N, previous FLOAT
Demand interval
Short Term
Maximum
- 8983 Volts A-B, previous FLOAT
Demand interval
Short Term
Maximum
- 8985 Volts B-C, previous FLOAT
Demand interval
Short Term
Maximum
- 8987 Volts C-A, previous FLOAT
Demand interval
Short Term
Maximum
- 8989 Volts A-N,
FLOAT
Maximum
- 8991 Volts B-N,
FLOAT
Maximum
- 8993 Volts C-N,
FLOAT
Maximum
- 8995 Volts A-B,
FLOAT
Maximum
- 8997 Volts B-C,
FLOAT
Maximum
- 8999 Volts C-A,
FLOAT
Maximum
read-only
0 to 9999 M volts
Maximum instantaneous
value measured during the
demand interval before the
one most recently
completed.
0 to 9999 M volts
0 to 9999 M volts
0 to 9999 M volts
0 to 9999 M volts
0 to 9999 M volts
0 to 9999 M volts
0 to 9999 M volts
Maximum instantaneous
2
value measured during the
most recently completed
2
demand interval.
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
Block Size:
Primary Maximum Block
2327
- 2328 9000
2329 - 232A 9002
232B - 232C 9004
232D - 232E 9006
232F - 2330 9008
2331 - 2332 9010
2333 - 2334 9012
2335 - 2336 9014
2337 - 2338 9016
2339 - 233A 9018
233B - 233C 9020
233D - 233E 9022
233F - 2340 9024
B–48
- 9001 Volts A-N,
FLOAT
Maximum
- 9003 Volts B-N,
FLOAT
Maximum
- 9005 Volts C-N,
FLOAT
Maximum
- 9007 Volts A-B,
FLOAT
Maximum
- 9009 Volts B-C,
FLOAT
Maximum
- 9011 Volts C-A,
FLOAT
Maximum
- 9013 Amps A, Maximum FLOAT
Avg Demand
- 9015 Amps B, Maximum FLOAT
Avg Demand
- 9017 Amps C, Maximum FLOAT
Avg Demand
- 9019 Positive Watts, 3- FLOAT
Ph, Maximum Avg
Demand
- 9021 Positive VARs, 3- FLOAT
Ph, Maximum Avg
Demand
- 9023 Negative Watts, 3- FLOAT
Ph, Maximum Avg
Demand
- 9025 Negative VARs, 3- FLOAT
Ph, Maximum Avg
Demand
12
read-only
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M amps
2
0 to 9999 M amps
2
0 to 9999 M amps
2
0 to +9999 M watts
2
0 to +9999 M VARs
2
0 to +9999 M watts
2
0 to +9999 M VARs
2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2341 - 2342 9026 - 9027 VAs, 3-Ph,
FLOAT
Maximum Avg
Demand
2343 - 2344 9028 - 9029 Positive Power
FLOAT
Factor, 3-Ph,
Maximum Avg
Demand
2345 - 2346 9030 - 9031 Negative Power FLOAT
Factor, 3-Ph,
Maximum Avg
Demand
2347 - 2348 9032 - 9033 Frequency,
FLOAT
Maximum
2349 - 234A 9034 - 9035 Neutral Current, FLOAT
Maximum Avg
Demand
234B - 234C 9036 - 9037 Positive Watts,
FLOAT
Phase A, Maximum
Avg Demand
234D - 234E 9038 - 9039 Positive Watts,
FLOAT
Phase B, Maximum
Avg Demand
234F - 2350 9040 - 9041 Positive Watts,
FLOAT
Phase C, Maximum
Avg Demand
2351 - 2352 9042 - 9043 Positive VARs,
FLOAT
Phase A, Maximum
Avg Demand
2353 - 2354 9044 - 9045 Positive VARs,
FLOAT
Phase B, Maximum
Avg Demand
2355 - 2356 9046 - 9047 Positive VARs,
FLOAT
Phase C, Maximum
Avg Demand
2357 - 2358 9048 - 9049 Negative Watts, FLOAT
Phase A, Maximum
Avg Demand
2359 - 235A 9050 - 9051 Negative Watts, FLOAT
Phase B, Maximum
Avg Demand
235B - 235C 9052 - 9053 Negative Watts, FLOAT
Phase C, Maximum
Avg Demand
235D - 235E 9054 - 9055 Negative VARs,
FLOAT
Phase A, Maximum
Avg Demand
235F - 2360 9056 - 9057 Negative VARs,
FLOAT
Phase B, Maximum
Avg Demand
2361 - 2362 9058 - 9059 Negative VARs,
FLOAT
Phase C, Maximum
Avg Demand
2363 - 2364 9060 - 9061 VAs, Phase A,
FLOAT
Maximum Avg
Demand
2365 - 2366 9062 - 9063 VAs, Phase B,
FLOAT
Maximum Avg
Demand
2367 - 2368 9064 - 9065 VAs, Phase C,
FLOAT
Maximum Avg
Demand
2369 - 236A 9066 - 9067 Positive PF, Phase FLOAT
A, Maximum Avg
Demand
236B - 236C 9068 - 9069 Positive PF, Phase FLOAT
B, Maximum Avg
Demand
236D - 236E 9070 - 9071 Positive PF, Phase FLOAT
C, Maximum Avg
Demand
236F - 2370 9072 - 9073 Negative PF, Phase FLOAT
A, Maximum Avg
Demand
2371 - 2372 9074 - 9075 Negative PF, Phase FLOAT
B, Maximum Avg
Demand
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
-9999 M to
+9999 M
VAs
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
0 to 65.00
Hz
2
0 to 9999 M amps
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
watts
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VARs
2
-9999 M to
+9999 M
VAs
2
-9999 M to
+9999 M
VAs
2
-9999 M to
+9999 M
VAs
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
-1.00 to
+1.00
none
2
B–49
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2373 - 2374 9076 - 9077 Negative PF, Phase FLOAT
C, Maximum Avg
Demand
2375 - 2375 9078 - 9078 Volts A-N, %THD, UINT16
Maximum
2376 - 2376 9079 - 9079 Volts B-N, %THD, UINT16
Maximum
2377 - 2377 9080 - 9080 Volts C-N, %THD, UINT16
Maximum
2378 - 2378 9081 - 9081 Amps A, %THD,
UINT16
Maximum
2379 - 2379 9082 - 9082 Amps B, %THD,
UINT16
Maximum
237A - 237A 9083 - 9083 Amps C, %THD,
UINT16
Maximum
237B - 237C 9084 - 9085 Symmetrical
FLOAT
Component
Magnitude, 0 Seq,
Maximum
237D - 237E 9086 - 9087 Symmetrical
FLOAT
Component
Magnitude, + Seq,
Maximum
237F - 2380 9088 - 9089 Symmetrical
FLOAT
Component
Magnitude, - Seq,
Maximum
2381 - 2381 9090 - 9090 Symmetrical
SINT16
Component Phase,
0 Seq, Maximum
2382 - 2382 9091 - 9091 Symmetrical
SINT16
Component Phase,
+ Seq, Maximum
2383 - 2383 9092 - 9092 Symmetrical
SINT16
Component Phase,
- Seq, Maximum
2384 - 2384 9093 - 9093 Unbalance, 0 Seq, UINT16
Maximum
2385 - 2385 9094 - 9094 Unbalance, - Seq, UINT16
Maximum
2386 - 2386 9095 - 9095 Current
UINT16
Unbalance,
Maximum
-1.00 to
+1.00
none
2
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999
0.01%
1
0 to 9999 M volts
2
0 to 9999 M volts
2
0 to 9999 M volts
2
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
-1800 to
+1800
0.1 degree
1
0 to 65535
0.01%
1
0 to 65535
0.01%
1
0 to 20000
0.01%
1
Block Size:
Primary Maximum Timestamp Block
24B7
- 24B9 9400
24BA - 24BC 9403
24BD - 24BF 9406
24C0 - 24C2 9409
24C3 - 24C5 9412
24C6 - 24C8 9415
24C9 - 24CB 9418
24CC - 24CE 9421
24CF - 24D1 9424
24D2 - 24D4 9427
24D5 - 24D7 9430
24D8 - 24DA 9433
B–50
- 9402 Volts A-N, Max
TSTAMP
Timestamp
- 9405 Volts B-N, Max
TSTAMP
Timestamp
- 9408 Volts C-N, Max
TSTAMP
Timestamp
- 9411 Volts A-B, Max
TSTAMP
Timestamp
- 9414 Volts B-C, Max
TSTAMP
Timestamp
- 9417 Volts C-A, Max
TSTAMP
Timestamp
- 9420 Amps A, Max Avg TSTAMP
Dmd Timestamp
- 9423 Amps B, Max Avg TSTAMP
Dmd Timestamp
- 9426 Amps C, Max Avg TSTAMP
Dmd Timestamp
- 9429 Positive Watts, 3- TSTAMP
Ph, Max Avg Dmd
Timestamp
- 9432 Positive VARs, 3- TSTAMP
Ph, Max Avg Dmd
Timestamp
- 9435 Negative Watts, 3- TSTAMP
Ph, Max Avg Dmd
Timestamp
96
read-only
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
24DB - 24DD 9436 - 9438 Negative VARs, 3- TSTAMP
Ph, Max Avg Dmd
Timestamp
24DE - 24E0 9439 - 9441 VAs, 3-Ph, Max Avg TSTAMP
Dmd Timestamp
24E1 - 24E3 9442 - 9444 Positive Power
TSTAMP
Factor, 3-Ph, Max
Avg Dmd
Timestamp
24E4 - 24E6 9445 - 9447 Negative Power TSTAMP
Factor, 3-Ph, Max
Avg Dmd
Timestamp
24E7 - 24E9 9448 - 9450 Frequency, Max TSTAMP
Timestamp
24EA - 24EC 9451 - 9453 Neutral Current, TSTAMP
Max Avg Dmd
Timestamp
24ED - 24EF 9454 - 9456 Positive Watts,
TSTAMP
Phase A, Max Avg
Dmd Timestamp
24F0 - 24F2 9457 - 9459 Positive Watts,
TSTAMP
Phase B, Max Avg
Dmd Timestamp
24F3 - 24F5 9460 - 9462 Positive Watts,
TSTAMP
Phase C, Max Avg
Dmd Timestamp
24F6 - 24F8 9463 - 9465 Positive VARs,
TSTAMP
Phase A, Max Avg
Dmd Timestamp
24F9 - 24FB 9466 - 9468 Positive VARs,
TSTAMP
Phase B, Max Avg
Dmd Timestamp
24FC - 24FE 9469 - 9471 Positive VARs,
TSTAMP
Phase C, Max Avg
Dmd Timestamp
24FF - 2501 9472 - 9474 Negative Watts, TSTAMP
Phase A, Max Avg
Dmd Timestamp
2502 - 2504 9475 - 9477 Negative Watts, TSTAMP
Phase B, Max Avg
Dmd Timestamp
2505 - 2507 9478 - 9480 Negative Watts, TSTAMP
Phase C, Max Avg
Dmd Timestamp
2508 - 250A 9481 - 9483 Negative VARs,
TSTAMP
Phase A, Max Avg
Dmd Timestamp
250B - 250D 9484 - 9486 Negative VARs,
TSTAMP
Phase B, Max Avg
Dmd Timestamp
TSTAMP
250E - 2510 9487 - 9489 Negative VARs,
Phase C, Max Avg
Dmd Timestamp
2511 - 2513 9490 - 9492 VAs, Phase A, Max TSTAMP
Avg Dmd
Timestamp
2514 - 2516 9493 - 9495 VAs, Phase B, Max TSTAMP
Avg Dmd
Timestamp
2517 - 2519 9496 - 9498 VAs, Phase C, Max TSTAMP
Avg Dmd
Timestamp
251A - 251C 9499 - 9501 Positive PF, Phase TSTAMP
A, Max Avg Dmd
Timestamp
251D - 251F 9502 - 9504 Positive PF, Phase TSTAMP
B, Max Avg Dmd
Timestamp
2520 - 2522 9505 - 9507 Positive PF, Phase TSTAMP
C, Max Avg Dmd
Timestamp
2523 - 2525 9508 - 9510 Negative PF, Phase TSTAMP
A, Max Avg Dmd
Timestamp
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2100
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
3
3
B–51
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2526 - 2528 9511 - 9513 Negative PF, Phase TSTAMP
B, Max Avg Dmd
Timestamp
2529 - 252B 9514 - 9516 Negative PF, Phase TSTAMP
C, Max Avg Dmd
Timestamp
252C - 252E 9517 - 9519 Volts A-N, %THD, TSTAMP
Max Timestamp
252F - 2531 9520 - 9522 Volts B-N, %THD, TSTAMP
Max Timestamp
2532 - 2534 9523 - 9525 Volts C-N, %THD, TSTAMP
Max Timestamp
2535 - 2537 9526 - 9528 Amps A, %THD,
TSTAMP
Max Timestamp
2538 - 253A 9529 - 9531 Amps B, %THD,
TSTAMP
Max Timestamp
253B - 253D 9532 - 9534 Amps C, %THD,
TSTAMP
Max Timestamp
253E - 2540 9535 - 9537 Symmetrical Comp TSTAMP
Magnitude, 0 Seq,
Max Timestamp
2541 - 2543 9538 - 9540 Symmetrical Comp TSTAMP
Magnitude, + Seq,
Max Timestamp
2544 - 2546 9541 - 9543 Symmetrical Comp TSTAMP
Magnitude, - Seq,
Max Timestamp
2547 - 2549 9544 - 9546 Symmetrical Comp TSTAMP
Phase, 0 Seq, Max
Timestamp
254A - 254C 9547 - 9549 Symmetrical Comp TSTAMP
Phase, + Seq, Max
Timestamp
254D - 254F 9550 - 9552 Symmetrical Comp TSTAMP
Phase, - Seq, Max
Timestamp
2550 - 2552 9553 - 9555 Unbalance, 0 Seq, TSTAMP
Max Timestamp
2553 - 2555 9556 - 9558 Unbalance, - Seq, TSTAMP
Max Timestamp
2556 - 2558 9559 - 9561 Current
TSTAMP
Unbalance, Max
Timestamp
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1Jan2000 31Dec2099
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1 sec
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
3
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
1Jan2000 - 1 sec
31Dec2099
3
3
3
Block Size:
159
OPTION CARD 1 SECTION
Card Identification and Configuration Block
(Note 14)
270F - 270F 10000 - 10000 Class ID and card UINT16
status
read-only
bit-mapped undv-----cccctttt
Flags active if bit is set:
1
u=unsupported card; n=card
need configuration; d=card
is using default
configuration;
v=communication with card
is ok
Field: cccc=class of installed
card.
Field tttt=type of card. See
note 22
Reserved
1
ASCII name of the installed 8
card
Serial Number in ASCII of the 8
installed card
Version in ASCII of the
2
hardware of the installed
card.
Reserved
36
2710 - 2710 10001 - 10001 Reserved
2711 - 2718 10002 - 10009 Card name
ASCII
16 char
none
2719 - 2720 10010 - 10017 Serial number
ASCII
16 char
none
2721 - 2722 10018 - 10019 Version
ASCII
4 char
none
2723 - 2746 10020 - 10055 Reserved
B–52
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2747 - 2748 10056 - 10057 Firmware Version ASCII
4 char
none
2749 - 274A 10058 - 10059 Firmware Version ASCII
4 char
none
274B - 274E 10060 - 10063 Reserved
Version of the BOOT
2
firmware of the card, left
justified and padded with
spaces. Blank for boards
without embedded
firmware.
Version of the RUN firmware 2
of the card, left justified and
padded with spaces. Blank
for boards without
embedded firmware.
Reserved
4
Block Size:
Current Communication Settings for Option
Card 1
274F - 274F 10064 - 10064 Current speed and UINT16
format
Read-only
bit-mapped -abcde-- fghijklm
2750 - 2750 10065 - 10065 Reserved
UINT16
bit-mapped
2751 - 2751 10066 - 10066 Current protocol
UINT16
bit-mapped -------- -----ppp-
2752 - 2752 10067 - 10067 Current reply delayUINT16
64
0 to 65535
milliseconds
2753 - 2756 10068 - 10071 Reserved
Bps: a=57600; b=38400;
1
c=19200; d=14400; e=9600
Stop bits 'f': cleared 1 stop
bit, set 2 stop bits
Parity: g=even; h=odd;
i=none
Data bits: j=8; k=7; l=6; m=5
Reserved
1
ppp=protocol
1
100=DNP3; 010=Ascii
Modbus; 001=Rtu Modbus
Delay to reply to a Modbus 1
transaction after receiving it.
Reserved
4
Block Size:
8
Data and Control Blocks for Option Card 1
read-only
2757 - 2790 10072 - 10129 Data and Control
Block for Option
Card 1. Meaning of
registers depends
on installed card. - see below
Register assignments
depend on which type of
card is in the slot. See
overlays below.
58
Block Size:
66
EXPANSIONS FOR DATA AND CONTROL BLOCK FOR OPTION CARD 1
Data and Control Block -- Digital I/O Relay Card
Overlay (Note 15)
2757 - 2757 10072 - 10072 Digital Input StatesUINT16
2758 - 2758 10073 - 10073 Digital Relay
States
UINT16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
bit-mapped -------- 22221111
bit-mapped -------- --ab--cd
read-only except as
indicated
Two nibble fields: (2222) for 1
input#2 and (1111) for input
#1.
Lsb in each nibble is the
current state of the input.
Msb in each nibble is the
oldest registered state.
If "a" is 1 then state of
1
Relay#2 is unknown,
otherwise state of Relay#2 is
in "c": (1=tripped,
0=released).
If "b" is 1 then state of
Relay#1 is unknown,
otherwise state of Relay#1 is
in "d": (1=tripped,
0=released).
B–53
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2759 - 2759 10074 - 10074 Turn relay on
UINT16
bit-mapped -------- ------21
275B - 275B 10076 - 10076 Trip/Release delay UINT16
timer for Relay 1
275C - 275C 10077 - 10077 Trip/Release delay UINT16
timer for Relay 2
275D - 275E 10078 - 10079 Reserved
0 to 9999
0.1 sec
Writing a 1 in bit N turns
1
relay N+1 ON (this register is
writeable only in privileged
session)
Writing a 1 in bit N turns
1
relay N+1 OFF (this register
is writeable only in privileged
session)
time to trip or release
1
275A - 275A 10075 - 10075 Turn relay off
UINT16
bit-mapped -------- ------21
0 to 9999
0.1 sec
time to trip or release
1
Reserved
2
275F - 275F 10080 - 10080 Input 1
Accumulator,
Scaled
2760 - 2760 10081 - 10081 Input 2
Accumulator,
Scaled
2761 - 2762 10082 - 10083 Reserved
UINT16
0 to 9999
UINT16
0 to 9999
2763 - 2763 10084 - 10084 Relay 1
Accumulator,
Scaled
2764 - 2764 10085 - 10085 Relay 2
Accumulator,
Scaled
2765 - 2790 10086 - 10129 Reserved
Reserved
UINT16
0 to 9999
UINT16
0 to 9999
Data and Control Block -- Digital I/O Pulse Output
Card Overlay (Note 15)
2757 - 2757 10072 - 10072 Digital Input StatesUINT16
2758 - 2758 10073 - 10073 Digital Output
States
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
bit-mapped dddd cccc bbbb aaaa
UINT16
bit-mapped -------- ----4321
2759 - 2759 10074 - 10074 Pulse Output Test UINT16
Select
bit-mapped -------- ----4321
B–54
1
1
2
1
1
Reserved
44
Block Size:
58
read-only except as
indicated
Nibble "dddd" for input#4, 1
"cccc" for input#3, "bbbb" for
input#2 and "aaaa" for
input#1.
Within each field, rightmost
bit is the current state
(1=closed, 0=open), and bits
at left are the older states
100ms apart. (historical
states)
Example:
xxxx xxxx xxxx 0011
Current state of input#1 is
closed, before that it was
closed too, before that it was
open and the oldest state
known is open.
One bit for each output. Bit 4 1
is for output #4, and bit 1 is
for output #1. If a bit is set
the output is closed,
otherwise it is opened.
Write 1 to a bit to set its
1
corresponding Pulse Output
into test mode. Write 0 to
restore it to normal
operation. A privileged
session is required to write
the bits. Reading this
register reports the mode for
each output (1=under test,
0=normal).
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
275A - 275A 10075 - 10075 Pulse Output Test UINT16
Power
bit-mapped ddvvvvvv vvvvvvvv
275B - 275E 10076 - 10079 Reserved
275F - 275F 10080 - 10080 Input 1
Accumulator,
Scaled
2760 - 2760 10081 - 10081 Input 2
Accumulator,
Scaled
2761 - 2761 10082 - 10082 Input 3
Accumulator,
Scaled
2762 - 2762 10083 - 10083 Input 4
Accumulator,
Scaled
2763 - 2763 10084 - 10084 Output 1
Accumulator,
Scaled
2764 - 2764 10085 - 10085 Output 2
Accumulator,
Scaled
2765 - 2765 10086 - 10086 Output 3
Accumulator,
Scaled
2766 - 2766 10087 - 10087 Output 4
Accumulator,
Scaled
2767 - 2790 10088 - 10129 Reserved
Data and Control Block--Analog Out 0-1mA /
Analog Out 4-20mA (Note 15)
2757 - 2757 10072 - 10072 Status of card
This register is Writeable in 1
privileged session only.
Simulates constant Power
for the Pulse Output under
test. Format is same as Kt
settings for Pulse Output.
"V" is raw value in Wh/pulse
from 0 to 9999.
"dd"=decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= XXX.X
Reserved
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
4
UINT16
0 to 9999
1
UINT16
0 to 9999
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
1
Reserved
42
Block Size:
58
read-only
UINT16
bit-mapped ----cf-- --------
2758 - 2790 10073 - 10129 Reserved
Data and Control Block -- Network Card Overlay
(Note 15)
2757 - 2757 10072 - 10072 Card and Network UINT16
Status
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1
Reserved
57
Block Size:
58
read-only
bit-mapped rhp----- sfw-m-ii
Flags: r=run mode; h=card is 1
healthy; p=using last good
known programmable
settings
Server flags: s=smtp ok; f=ftp
ok; w=web server ok;
m=modbus tcp/ip ok.
IP Status ii: 00=IP not valid
yet, 01=IP from p.settings;
10=IP from DHCP;11=using
last good known IP.
Reserved
1
bit-mapped 6 bytes
These 3 registers hold the 6 3
bytes of the card's ethernet
MAC address
2758 - 2758 10073 - 10073 Reserved
2759 - 275B 10074 - 10076 MAC address in
UINT16
use by the network
card
Flag fields:
c=calibration not good;
f=configuration error
B–55
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
275C - 275F 10077 - 10080 Current IP Address UINT16
2760 - 2760 10081 - 10081 Current IP Mask
Length
UINT16
These 4 registers hold the 4 4
numbers (1 number each
register) that make the IP
address used by the card.
0 to 32
2761 - 2762 10082 - 10083 Firmware Version ASCII
4 char
none
2763 - 2764 10084 - 10085 Firmware Version ASCII
4 char
none
2765 - 2790 10086 - 10129 Reserved
Number of bits that are set 1
in the IP address mask,
starting from the Msb of the
32 bit word.
Example 24 = 255.255.255.0;
a value of 2 would mean
192.0.0.0
Version of the BOOT
2
firmware of the card, left
justified and padded with
spaces. Blank for boards
without embedded
firmware.
Version of the RUN firmware 2
of the card, left justified and
padded with spaces. Blank
for boards without
embedded firmware.
Reserved for Extended Nw 44
Status
Block Size:
58
OPTION CARD 2 SECTION
Card Identification and Configuration Block
(Note 14)
2AF7 - 2AF7 11000 - 11000 Class ID and card UINT16
status
read-only
bit-mapped undv-----cccctttt
Flags active if bit is set:
1
u=unsupported card; n=card
need configuration; d=card
is using default
configuration;
v=communication with card
is ok
Field: cccc=class of installed
card.
Field tttt=type of card. See
note 22
Read only
1
ASCII name of the installed 8
card
Serial Number in ASCII of the 8
installed card
Version in ASCII of the
2
hardware of the installed
card.
Reserved
36
2AF8 - 2AF8 11001 - 11001 Reserved
2AF9 - 2B00 11002 - 11009 Card name
ASCII
16 char
none
2B01 - 2B08 11010 - 11017 Serial number
ASCII
16 char
none
2B09 - 2B0A 11018 - 11019 Version
ASCII
4 char
none
2B2F - 2B30 11056 - 11057 Firmware Version ASCII
4 char
none
2B31 - 2B32 11058 - 11059 Firmware Version ASCII
4 char
none
2B0B - 2B28 11020 - 11055 Reserved
2B33 - 2B36 11060 - 11063 Reserved
Version of the BOOT
2
firmware of the card, left
justified and padded with
spaces. Blank for boards
without embedded
firmware.
Version of the RUN firmware 2
of the card, left justified and
padded with spaces. Blank
for boards without
embedded firmware.
Reserved
4
Block Size:
B–56
64
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Current Communication Settings for Option
Card 2
2B37 - 2B37 11064 - 11064 Current speed and UINT16
format
Read-only
bit-mapped -abcde-- fghijklm
2B38 - 2B38 11065 - 11065 Reserved
UINT16
bit-mapped
2B39 - 2B39 11066 - 11066 Current protocol
UINT16
bit-mapped -------- -----ppp-
2B3A - 2B3A 11067 - 11067 Current reply delayUINT16
0 to 65535
milliseconds
2B3B - 2B3E 11068 - 11071 Reserved
Bps: a=57600; b=38400;
1
c=19200; d=14400; e=9600
Stop bits 'f': cleared 1 stop
bit, set 2 stop bits
Parity: g=even; h=odd;
i=none
Data bits: j=8; k=7; l=6; m=5
Reserved
1
ppp=protocol
1
100=DNP3; 010=Ascii
Modbus; 001=Rtu Modbus
Delay to reply a Modbus
1
transaction after receiving it.
Reserved
4
Block Size:
8
Data and Control Blocks for Option Card 2
read-only
2B3F - 2B78 11072 - 11129 Data and Control
Block for Option
Card 2 Meaning of
registers depend
on installed card. - see below
Register assignments
depend on which type of
card is in the slot. See
overlays below.
58
Block Size:
66
EXPANSIONS FOR DATA AND CONTROL BLOCK FOR OPTION CARD 2
Data and Control Block -- Digital I/O Relay Card
Overlay (Note 15)
2B3F - 2B3F 11072 - 11072 Digital Input StatesUINT16
0 to 9999
0.1 sec
read-only except as
indicated
Two nibble fields: (2222) for 1
input#2 and (1111) for input
#1.
Lsb in each nibble is the
current state of the input.
Msb in each nibble is the
oldest registered state.
If "a" is 1 then state of
1
Relay#2 is unknown,
otherwise state of Relay#2 is
in "c": (1=tripped,
0=released).
If "b" is 1 then state of
Relay#1 is unknown,
otherwise state of Relay#1 is
in "d": (1=tripped,
0=released).
Writing a 1 in bit N turns
1
relay N+1 ON (this register is
writeable only in privileged
session)
Writing a 1 in bit N turns
1
relay N+1 OFF (this register
is writeable only in privileged
session)
time to trip or release
1
0 to 9999
0.1 sec
time to trip or release
1
Reserved
2
bit-mapped -------- 22221111
2B40 - 2B40 11073 - 11073 Digital Relay
States
UINT16
bit-mapped -------- --ab--cd
2B41 - 2B41 11074 - 11074 Turn relay on
UINT16
bit-mapped -------- ------21
2B42 - 2B42 11075 - 11075 Turn relay off
UINT16
bit-mapped -------- ------21
2B43 - 2B43 11076 - 11076 Trip/Release delay UINT16
timer for Relay 1
2B44 - 2B44 11077 - 11077 Trip/Release delay UINT16
timer for Relay 2
2B45 - 2B46 11078 - 11079 Reserved
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–57
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2B47 - 2B47 11080 - 11080 Input 1
Accumulator,
Scaled
2B48 - 2B48 11081 - 11081 Input 2
Accumulator,
Scaled
2B49 - 2B4A 11082 - 11083 Reserved
2B4B - 2B4B 11084 - 11084 Relay 1
Accumulator,
Scaled
2B4C - 2B4C 11085 - 11085 Relay 2
Accumulator,
Scaled
2B4D - 2B78 11086 - 11129 Reserved
UINT16
0 to 9999
UINT16
0 to 9999
Reserved
UINT16
0 to 9999
UINT16
0 to 9999
Data and Control Block -- Digital I/O Pulse Output
Card Overlay (Note 15)
2B3F - 2B3F 11072 - 11072 Digital Input StatesUINT16
2B40 - 2B40 11073 - 11073 Digital Output
States
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
bit-mapped dddd cccc bbbb aaaa
UINT16
bit-mapped -------- ----4321
2B41 - 2B41 11074 - 11074 Pulse Output Test UINT16
Select
bit-mapped -------- ----4321
2B42 - 2B42 11075 - 11075 Pulse Output Test UINT16
Power
bit-mapped ddvvvvvv vvvvvvvv
2B43 - 2B46 11076 - 11079 Reserved
B–58
1
1
2
1
1
Reserved
44
Block Size:
58
read-only except as
indicated
Nibble "dddd" for input#4, 1
"cccc" for input#3, "bbbb" for
input#2 and "aaaa" for
input#1.
Within each field, right most
bit is the current state
(1=closed, 0=open), and bits
at left are the older states
100ms apart. (historical
states)
Example:
xxxx xxxx xxxx 0011
Current state of input#1 is
closed, before that it was
closed too, before that it was
open and the oldest state
known is open.
One bit for each output. Bit 4 1
is for output #4, and bit 1 is
for output #1. If a bit is set
the output is closed,
otherwise it is opened.
Write 1 to a bit to set its
1
corresponding Pulse Output
into test mode. Write 0 to
restore it to normal
operation. A privileged
session is required to write
the bits. Reading this
register reports the mode for
each output (1=under test,
0=normal).
This register is Writeable in 1
privileged session only.
Simulates constant Power
for the Pulse Output under
test. Format is same as Kt
settings for Pulse Output.
"V" is raw value in Wh/pulse
from 0 to 9999.
"dd"=decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= XXX.X
Reserved
4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2B47 - 2B47 11080 - 11080 Input 1
Accumulator,
Scaled
2B48 - 2B48 11081 - 11081 Input 2
Accumulator,
Scaled
2B49 - 2B49 11082 - 11082 Input 3
Accumulator,
Scaled
2B4A - 2B4A 11083 - 11083 Input 4
Accumulator,
Scaled
2B4B - 2B4B 11084 - 11084 Output 1
Accumulator,
Scaled
2B4C - 2B4C 11085 - 11085 Output 2
Accumulator,
Scaled
2B4D - 2B4D 11086 - 11086 Output 3
Accumulator,
Scaled
2B4E - 2B4E 11087 - 11087 Output 4
Accumulator,
Scaled
2B4F - 2B78 11088 - 11129 Reserved
UINT16
0 to 9999
UINT16
0 to 9999
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
UINT16
0 to 9999
1
Data and Control Block--Analog Out 0-1mA /
Analog Out 4-20mA (Note 15)
2B3F - 2B3F 11072 - 11072 Status of card
UINT16
2B40 - 2B78 11073 - 11129 Reserved
UINT16
resolution is 1, 10, 100, Disabled accumulators
1000, 10000, or 100000 always read 0.
counts
1
1
Reserved
42
Block Size:
58
read-only
Data and Control Block -- Network Card Overlay
(Note 15)
2B3F - 2B3F 11072 - 11072 Card and Network UINT16
Status
bit-mapped ----cf-- --------
Flag fields:
c=calibration not good;
f=configuration error
1
Reserved
57
Block Size:
58
read-only
bit-mapped rhp----- sfw-m-ii
Flags: r=run mode; h=card is 1
healthy; p=using last good
known programmable
settings
Server flags: s=smtp ok; f=ftp
ok; w=web server ok;
m=modbus tcp/ip ok.
IP Status ii: 00=IP not valid
yet, 01=IP from p.settings;
10=IP from DHCP;11=using
last good known IP.
Reserved
1
2B41 - 2B43 11074 - 11076 MAC address in
UINT16
use by the network
card
2B44 - 2B47 11077 - 11080 Current IP Address UINT16
bit-mapped 6 bytes
These 3 registers hold the 6 3
bytes of the card's Ethernet
MAC address.
These 4 registers hold the 4 4
numbers (1 number each
register) that make the IP
address used by the card.
2B48 - 2B48 11081 - 11081 Current IP Mask
Length
0 to 32
Number of bits that are set 1
in the IP address mask,
starting from the Msb of the
32 bit word.
Example 24 = 255.255.255.0;
a value of 2 would mean
192.0.0.0
2B40 - 2B40 11073 - 11073 Reserved
UINT16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–59
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
2B49 - 2B4A 11082 - 11083 Firmware Version ASCII
4 char
none
2B4B - 2B4C 11084 - 11085 Firmware Version ASCII
4 char
none
2B4D - 2B78 11086 - 11129 Reserved
Accumulators Block
2EDF
2EE1
2EE7
2EE9
2EEF
2EF7
Version of the BOOT
2
firmware of the card, left
justified and padded with
spaces. Blank for boards
without embedded
firmware.
Version of the RUN firmware 2
of the card, left justified and
padded with spaces. Blank
for boards without
embedded firmware.
Reserved for Extended Nw 44
Status
Block Size:
58
read-only
- 2EE0 12000 - 12001 Option Card 1,
Input 1
Accumulator
- 2EE6 12002 - 12007 Option Card 1,
Inputs 2-4
Accumulators
- 2EE8 12008 - 12009 Option Card 1,
Output or Relay 1
Accumulator
- 2EEE 12010 - 12015 Option Card 1,
Output or Relays
2-4 Accumulators
- 2EF6 12016 - 12023 Option Card 2
Inputs
Accumulators
- 2EFE 12024 - 12031 Option Card 2
Outputs
Accumulators
These are unscaled counts. 2
See option card section for
scaled versions.
Input accumulators count 6
either or both transitions;
output accumulators count
2
both transitions.
Unused accumulators
always read 0.
6
UINT32
0 to
number of transitions
999999999
UINT32
0 to
number of transitions
999999999
UINT32
0 to
number of transitions
999999999
UINT32
0 to
number of transitions
999999999
UINT32
0 to
number of transitions
999999999
8
UINT32
0 to
number of transitions
999999999
8
Block Size:
32
COMMANDS SECTION (NOTE 4)
Resets Block (Note 9)
4E1F
4E20
4E21
4E22
4E23
4E24
4E25
4E26
4E27
4E28
4E29
- 4E1F 20000 - 20000 Reset Max/Min
Blocks
- 4E20 20001 - 20001 Reset Energy
Accumulators
- 4E21 20002 - 20002 Reset Alarm Log
(Note 21)
- 4E22 20003 - 20003 Reset System Log
(Note 21)
- 4E23 20004 - 20004 Reset Historical
Log 1 (Note 21)
- 4E24 20005 - 20005 Reset Historical
Log 2 (Note 21)
- 4E25 20006 - 20006 Reset Historical
Log 3 (Note 21)
- 4E26 20007 - 20007 Reset I/O Change
Log (Note 21)
- 4E27 20008 - 20008 Reset Power
Quality Log
- 4E28 20009 - 20009 Reset Waveform
Capture Log
- 4E2A 20010 - 20011 Reserved
write-only
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
4E2B - 4E2B 20012 - 20012 Reset Option Card UINT16
1 Input
Accumulators
4E2C - 4E2C 20013 - 20013 Reset Option Card UINT16
1 Output
Accumulators
B–60
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
password
(Note 5)
1
1
Reply to a reset log
1
command indicates that the
command was accepted but 1
not necessarily that the
reset is finished. Poll log
1
status block to determine
this.
1
1
1
1
1
Reserved
2
password
(Note 5)
1
password
(Note 5)
1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
4E2D - 4E2D 20014 - 20014 Reset Option Card UINT16
2 Input
Accumulators
4E2E - 4E2E 20015 - 20015 Reset Option Card UINT16
2 Output
Accumulators
password
(Note 5)
1
password
(Note 5)
1
Block Size:
Privileged Commands Block
5207
- 5207 21000 - 21000 Initiate Meter
UINT16
Firmware
Reprogramming
5208 - 5208 21001 - 21001 Force Meter
UINT16
Restart
5209 - 5209 21002 - 21002 Open Privileged UINT16
Command Session
520A - 520A 21003 - 21003 Initiate
UINT16
Programmable
Settings Update
520B - 520B 21004 - 21004 Calculate
UINT16
Programmable
Settings Checksum
(Note 3)
520C - 520C 21005 - 21005 Programmable
UINT16
Settings Checksum
(Note 3)
conditional write
password
(Note 5)
1
password
(Note 5)
password
(Note 5)
causes a watchdog reset, 1
always reads 0
meter will process
1
command registers (this
register through 'Close
Privileged Command
Session' register below) for 5
minutes or until the session
is closed, whichever comes
first.
meter enters PS update
1
mode
password
(Note 5)
0000 to 9999
meter calculates checksum 1
on RAM copy of PS block
0000 to 9999
read/write checksum
1
register; PS block saved in
nonvolatile memory on write
(Note 8)
write-only register; always 1
reads zero
meter leaves PS update
1
mode via reset
520D - 520D 21006 - 21006 Write New
UINT16 0000 to 9999
Password (Note 3)
520E - 520E 21007 - 21007 Terminate
UINT16 any value
Programmable
Settings Update
(Note 3)
520F - 5211 21008 - 21010 Set Meter Clock TSTAMP 1Jan2000 - 1 sec
31Dec2099
5212 - 5212 21011 - 21011 Manually Trigger UINT16 any value
Waveform Capture
5213 - 5219 21012 - 21018 Reserved
521A - 521A 21019 - 21019 Close Privileged UINT16
Command Session
16
any value
saved only when 3rd register 3
is written
1
applies to EPM7000 300
only; returns busy exception
if blocked by another
capture in progress
Reserved
7
ends an open command
session
Block Size:
1
20
Encryption Block
read/write
658F
encrypted command to read 12
password or change meter
type
Block Size:
12
- 659A 26000 - 26011 Perform a Secure UINT16
Operation
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–61
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
PROGRAMMABLE SETTINGS SECTION
Basic Setups Block
- 752F 30000 - 30000 CT multiplier &
denominator
UINT16
bit-mapped dddddddd
mmmmmmmm
7530 - 7530 30001 - 30001 CT numerator
UINT16
1 to 9999
none
write only in PS update
mode
high byte is denominator (1 1
or 5, read-only),
low byte is multiplier (1, 10,
or 100)
1
7531 - 7531 30002 - 30002 PT numerator
UINT16
1 to 9999
none
1
7532 - 7532 30003 - 30003 PT denominator
UINT16
1 to 9999
none
1
7533 - 7533 30004 - 30004 PT multiplier &
hookup
UINT16
bit-mapped mmmmmmmm
mmmmhhhh
752F
7534 - 7534 30005 - 30005 Averaging Method UINT16
bit-mapped
7535 - 7535 30006 - 30006 Power & Energy
Format
UINT16
bit-mapped
7536 - 7536 30007 - 30007 Operating Mode
Screen Enables
UINT16
bit-mapped
7537 - 7537 30008 - 30008 Daylight Saving On UINT16
Rule
7538 - 7538 30009 - 30009 Daylight Saving Off UINT16
Rule
bit-mapped
7539 - 7539 30010 - 30010 Time Zone UTC
offset
B–62
UINT16
bit-mapped
bit-mapped
mm…mm = PT multiplier (1, 1
10, 100, or 1000)
hhhh = hookup enumeration
(0 = 3 element wye[9S], 1 =
delta 2 CTs[5S], 3 = 2.5
element wye[6S])
--iiiiii b----sss
iiiiii = interval (5,15,30,60) 1
b = 0-block or 1-rolling
sss = # subintervals (1,2,3,4)
ppppiinn feee-ddd
pppp = power scale (0-unit, 1
3-kilo, 6-mega, 8-auto)
ii = power digits after
decimal point (0-3),
applies only if f=1 and
pppp is not auto
nn = number of energy digits
(5-8 --> 0-3)
eee = energy scale (0-unit, 3kilo, 6-mega)
f = decimal point for power
(0=data-dependant
placement,
1=fixed placement per ii
value)
ddd = energy digits after
decimal point (0-6)
See note 10.
-------x eeeeeeee
eeeeeeee = op mode screen 1
rows on/off, rows top to
bottom are bits low order to
high order
x = set to suppress PF on W/
VAR/PF screens
hhhhhwww applies only if daylight
1
dddmmmm
savings in User Settings
Flags = on; specifies when to 1
hhhhhwww make changeover
dddmmmm
hhhhh = hour, 0-23
www = week, 1-4 for 1st 4th, 5 for last
ddd = day of week, 1-7 for
Sun - Sat
mmmm = month, 1-12
Example: 2AM on the 4th
Sunday of March
hhhhh=2, www=4, ddd=1,
mmmm=3
z000 0000 hhhh hhmm mm = minutes/15; 00=00, 1
01=15, 10=30, 11=45
hhhh = hours; -23 to +23
z = Time Zone valid (0=no,
1=yes)
i.e. register=0 indicates that
time zone is not set while
register=0x8000 indicates
UTC offset = 0
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
753A - 753A 30011 - 30011 Clock Sync
Configuration
UINT16
bit-mapped 0000 0000 mmm0 0ppe e = enable automatic clock 1
sync (0=no, 1=yes)
pp = port performing
synchronization (2-3 =
COM3-COM4)
mmm = sync method
(1=NTP, all other values=no
sync)
Reserved
1
753C - 753C 30013 - 30013 User Settings 2
UINT16
bit-mapped -------- -------s
753D - 753D 30014 - 30014 DNP Options
UINT16
bit-mapped -------- ww-i-vvp
753B - 753B 30012 - 30012 Reserved
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
s = display secondary volts 1
(1=yes, 0=no)
1
p selects primary or
secondary values for DNP
voltage, current and power
registers
(0=secondary, 1=primary)
vv sets divisor for voltage
scaling
(0=1, 1=10, 2=100)
i sets divisor for current
scaling
(0=1, 1=10)
ww sets divisor for power
scaling in addition to scaling
for Kilo
(0=1, 1=10, 2=100,
3=1000)
Example:
120KV, 500A, 180MW
p=1, vv=2, i=0, and ww=3
voltage reads 1200, current
reads 500, watts reads 180
B–63
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
753E - 753E 30015 - 30015 User Settings FlagsUINT16
bit-mapped vvkgeinn srpdywfa
753F - 753F 30016 - 30016 Full Scale Current UINT16
(for load % bar
graph)
0 to 9999
none
7540 - 7547 30017 - 30024 Meter Designation ASCII
16 char
none
7548 - 7548 30025 - 30025 COM1 setup
UINT16
bit-mapped ----dddd -0100110
7549 - 7549 30026 - 30026 COM2 setup
UINT16
bit-mapped ----dddd -ppp-bbb
754A - 754A 30027 - 30027 COM2 address
UINT16
1 to 247
754B - 754B 30028 - 30028 Limit #1 Identifier UINT16
0 to 65535
754C - 754C 30029 - 30029 Limit #1 Out High SINT16
Setpoint
-200.0 to
+200.0
B–64
none
0.1% of full scale
vv = number of digits after 1
decimal point for voltage
display.
0 - For voltage range (0 9999V)
1 - For voltage range
(100.0kV - 999.9 kV)
2 - For voltage range
(10.00kV - 99.99 kV)
3 - For voltage range (
0kV - 9.999 kV)
This setting is used only
when k=1.
k = enable fixed scale for
voltage display.
(0=autoscale, 1=unit if
vv=0 and kV if vv=1,2,3 )
g = enable alternate full
scale bar graph current
(1=on, 0=off)
e = enable ct pt
compensation
(0=Disabled, 1=Enabled).
i = fixed scale and format
current display
0=normal autoscaled
current display
1=always show amps
with no decimal places
nn = number of phases for
voltage & current screen
(3=ABC, 2=AB, 1=A,
0=ABC)
s = scroll (1=on, 0=off)
r = password for reset in use
(1=on, 0=off)
p = password for
configuration in use (1=on,
0=off)
d = daylight saving time
changes (0=off, 1=on)
y = diagnostic events in
system log (1=yes, 0=no)
w = power direction
(0=view as load, 1=view
as generator)
f = flip power factor sign
(1=yes, 0=no)
a = apparent power
computation method
(0=arithmetic sum,
1=vector sum)
If non-zero and user settings 1
bit g is set, this value
replaces CT numerator in the
full scale current calculation.
(See Note 12)
8
1
dddd = reply delay (* 50
msec)
ppp = protocol (1-Modbus 1
RTU, 2-Modbus ASCII, 3-DNP)
bbb = baud rate (1-9600, 219200, 4-38400, 6-57600)
1
use Modbus address as the 1
identifier (see notes 7, 11, 12)
Setpoint for the "above" limit 1
(LM1), see notes 11-12.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
754D - 754D 30030 - 30030 Limit #1 In High
Threshold
SINT16
-200.0 to
+200.0
0.1% of full scale
754E - 754E 30031 - 30031 Limit #1 Out Low SINT16
Setpoint
754F - 754F 30032 - 30032 Limit #1 In Low
SINT16
Threshold
-200.0 to
+200.0
-200.0 to
+200.0
0.1% of full scale
7550 - 7554 30033 - 30037 Limit #2
SINT16
same as Limit #1
7555 - 7559 30038 - 30042 Limit #3
SINT16
same as
Limit #1
755A - 755E 30043 - 30047 Limit #4
SINT16
5
755F - 7563 30048 - 30052 Limit #5
SINT16
5
7564 - 7568 30053 - 30057 Limit #6
SINT16
5
7569 - 756D 30058 - 30062 Limit #7
SINT16
5
756E - 7572 30063 - 30067 Limit #8
SINT16
5
0.1% of full scale
Threshold at which "above" 1
limit clears; normally less
than or equal to the "above"
setpoint; see notes 11-12.
Setpoint for the "below" limit 1
(LM2), see notes 11-12.
Threshold at which "below" 1
limit clears; normally greater
than or equal to the "below"
setpoint; see notes 11-12.
same as Limit #1
5
5
7573 - 7582 30068 - 30083 Reserved
Reserved
16
7583 - 75C2 30084 - 30147 Reserved
Reserved
64
75C3 - 75C3 30148 - 30148 watts loss due to UINT16
iron when watts
positive
75C4 - 75C4 30149 - 30149 watts loss due to UINT16
copper when
watts positive
75C5 - 75C5 30150 - 30150 var loss due to iron UINT16
when watts
positive
75C6 - 75C6 30151 - 30151 var loss due to
UINT16
copper when
watts positive
75C7 - 75C3 30152 - 30152 watts loss due to UINT16
iron when watts
negative
75C8 - 75C4 30153 - 30153 watts loss due to UINT16
8
copper when
watts negative
75C9 - 75C9 30154 - 30154 var loss due to iron UINT16
when watts
negative
75CA - 75CA 30155 - 30155 var loss due to
UINT16
copper when
watts negative
75CB - 75CB 30156 - 30156 transformer loss UINT16
compensation
user settings flag
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
0 to 99.99
0.01%
1
bit-mapped
-------- ----cfwv
75CC - 75E5 30157 - 30182 Reserved
75E6 - 75E6 30183 - 30183 Programmable
Settings Update
Counter
UINT16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
0-65535
c - 0 disable compensation 1
for losses due to copper,
1 enable compensaion
for losses due to copper
f - 0 disable compensation
for losses due to iron,
1 enable compensaion
for losses due to iron
w - 0 add watt
compensation,
1 subtract watt
compensation
v - 0 add var compensation,
1 subtract var
compensation
Reserved
26
1
Increments each time
programmable settings are
changed; occurs when new
checksum is calculated.
B–65
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
75E7 - 7626 30184 - 30247 Reserved for
Software Use
7627 - 7627 30248 - 30248 A phase PT
compensation @
69V (% error)
7628 - 7628 30249 - 30249 A phase PT
compensation @
120V (% error)
7629 - 7629 30250 - 30250 A phase PT
compensation @
230V (% error)
762A - 762A 30251 - 30251 A phase PT
compensation @
480V (% error)
762B - 762B 30252 - 30255 B phase PT
compensation @
69V, 120V, 230V,
480V (% error)
762F - 762F 30256 - 30259 C phase PT
compensation @
69V, 120V, 230V,
480V (% error)
7633 - 7633 30260 - 30260 A phase CT
compensation @
c1 (% error)
7634 - 7634 30261 - 30261 A phase CT
compensation @
c2 (% error)
7635 - 7635 30262 - 30262 A phase CT
compensation @
c3 (% error)
7636 - 7636 30263 - 30263 A phase CT
compensation @
c4 (% error)
7637 - 7637 30264 - 30267 B phase CT
compensation @
c1, c2, c3, c4 (%
error)
763B - 763E 30268 - 30271 C phase CT
compensation @
c1, c2, c3, c4 (%
error)
763F - 7642 30272 - 30275 A phase PF
compensation @
c1, c2, c3, c4
7643 - 7646 30276 - 30279 B phase PF
compensation @
c1, c2, c3, c4
7647 - 764A 30280 - 30283 C phase PF
compensation @
c1, c2, c3, c4
Reserved
SINT16
-15 to 15
0.01%
1
SINT16
-15 to 15
0.01%
1
SINT16
-15 to 15
0.01%
1
SINT16
-15 to 15
0.01%
1
SINT16
-15 to 15
0.01%
4
SINT16
-15 to 15
0.01%
4
SINT16
-15 to 15
0.01%
SINT16
-15 to 15
0.01%
SINT16
-15 to 15
0.01%
SINT16
-15 to 15
0.01%
SINT16
-15 to 15
0.01%
4
SINT16
-15 to 15
0.01%
4
SINT16
-50 to 50
4
SINT16
-50 to 50
4
SINT16
-50 to 50
4
- 7917 31000 - 31000 Historical Log #1 UINT16
Sizes
bit-mapped eeeeeeee ssssssss
7918 - 7918 31001 - 31001 Historical Log #1 UINT16
Interval
bit-mapped 00000000 hgfedcba
7919 - 7919 31002 - 31002 Historical Log #1, UINT16
Register #1
Identifier
791A - 798D 31003 - 31118 Historical Log #1, UINT16
Register #2 - #117
Identifiers
0 to 65535
B–66
For Class 10 unit
c1=0.25A
c2=0.5A
c3=1A
c4=5A
1
For Class 2 unit
c1=0.05A
c2=0.1A
c3=0.2A
c4=1A
1
Block Size:
Log Setups Block
7917
64
0 to 65535
1
1
284
write only in PS update
mode
high byte is number of
1
registers to log in each
record (0-117),
low byte is number of flash
sectors for the log (see note
19)
0 in either byte disables the
log
only 1 bit set: a=1 min, b=3 1
min, c=5 min, d=10 min,
e=15 min, f=30 min, g=60
min, h=EOI pulse
use Modbus address as the 1
identifier (see note 7)
same as Register #1
Identifier
116
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
798E - 79D6 31119 - 31191 Historical Log #1
Software Buffer
79D7 - 7A96 31192 - 31383 Historical Log #2 same as Historical Log #1
Sizes, Interval,
Registers &
Software Buffer
7A97 - 7B56 31384 - 31575 Historical Log #3 same as Historical Log #1
Sizes, Interval,
Registers &
Software Buffer
7B57 - 7B57 31576 - 31607 Waveform Log
UINT16 bit-mapped ssssssss pppppppp
Sample Rate &
Pretrigger
7B58 - 7B58 31577 - 31577 Power Quality Log UINT16
Triggers
7B59 - 7B59 31578 - 31578 Waveform Log
UINT16
Triggers
7B5A - 7B5A 31579 - 31579 Waveform & PQ
Log Sizes
UINT16
bit-mapped -------8 76543210
bit-mapped -------8 76543210
bit-mapped pppppppp
wwwwwwww
7B5B - 7B5B 31580 - 31580 Reserved
7B5C - 7B5C 31581 - 31581 Channel A Voltage UINT16
Surge Threshold
7B5D - 7B5D 31582 - 31582 Channel A Current UINT16
Surge Threshold
7B5E - 7B5E 31583 - 31583 Channel A Voltage UINT16
Sag Threshold
7B5F - 7B61 31584 - 31586 Reserved
0 to 3276.7
0.1% of full scale
0 to 3276.7
0.1% of full scale
0 to 3276.7
0.1% of full scale
7B62 - 7B67 31587 - 31592 Channel B Surge & same as Channel A
Sag Thresholds
7B68 - 7B6D 31593 - 31598 Channel C Surge & same as Channel A
Sag Thresholds
7B6E - 7B76 31599 - 31607 Reserved
Reserved for software use. 73
192
192
High byte is samples/60Hz 1
cycle = 5(32), 6(64), 7(128),
8(256), or 9(512)
Low byte is number of
pretrigger cycles.
Set bits to enable PQ events/1
waveform captures.
2,1,0 = Voltage Surge,
1
channel C, B, A
5,4,3 = Current Surge,
channel C, B, A
8,7,6 = Voltage Sag,
channel C, B, A
High byte is number of flash 1
sectors for PQ log,
Low byte is number of flash
sectors for waveform log
Reserved
1
Thresholds are % of full
scale, see note 12
1
1
1
Reserved
3
6
6
Reserved
9
Block Size:
608
PROGRAMMABLE SETTINGS FOR OPTION CARD 1
Option Card 1 Setups Block
write only in PS update
mode
7CFF - 7CFF 32000 - 32000 Class ID of the
UINT16 bit-mapped -------- cccctttt
Which class (cccc) and
Option Card 1
type(tttt) of card the Option
Settings
Settings for Card 1 apply to.
See note 22.
7D00 - 7D3E 32001 - 32063 Settings for Option Register assignments depend on which type of card is in the slot. See
Card 1, First
overlays below.
Overlay -- see
below
7D3F - 7F3E 32064 - 32575 Settings for Option Register assignments depend on which type of card is in the slot. See
Card 1, Second
overlays below.
Overlay -- see
below
Block Size:
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1
63
512
576
B–67
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
OVERLAYS FOR OPTION CARD 1 PROGRAMMABLE SETTINGS
Settings Registers for any communication capable card, including
First Overlay
network and analog cards
7D00 - 7D00 32001 - 32001 Slave address
UINT16 1~247 (for none
Modbus)
1~65534 (for
DNP)
write only in PS update
mode
Slave address of the unit.
1
The communication capable
card is always a master.
Set to 0 when an analog
board is installed.
7D01 - 7D01 32002 - 32002 Speed and format UINT16
Bps: a=57600; b=38400;
1
c=19200; d=14400; e=9600
Stop bits 'f': cleared 1 stop
bit, set 2 stop bits
Parity: g=even; h=odd;
i=none
Data bits: j=8; k=7; l=6; m=5
Set to 0 when an analog
board is installed.
bit-mapped -abcde--fghijklm
7D02 - 7D02 32003 - 32003 Reserved
Reserved
1
7D03 - 7D03 32004 - 32004 Protocol
UINT16
bit-mapped -------- -----ppp-
ppp= 100 =DNP3; 010=Ascii 1
Modbus; 001=Rtu Modbus
Set to 0 when an analog
board is installed.
7D04 - 7D04 32005 - 32005 Reply delay
UINT16
0 to 65535
Delay to reply to a Modbus 1
transaction after receiving it.
Set to 0 when an analog
board is installed
Reserved
58
milliseconds
7D05 - 7D3E 32006 - 32063 Reserved
Block Size:
Settings Registers for Digital I/O Relay Card
First Overlay
7D00 - 7D00 32001 - 32001 Input#1 - 2
UINT16
bindings & logging
enables
bit-mapped -------- 2222 1111
7D01 - 7D01 32002 - 32002 Relay #1 Delay to UINT16
Operate
7D02 - 7D02 32003 - 32003 Relay #1 Delay to UINT16
Release
7D03 - 7D08 32004 - 32009 Reserved
UINT16
0.1 second
units
0.1 second
units
B–68
0x0001
for
analog
and
network
cards
(non
configura
ble)
0x0001
Fiber
cards
Don't
care for
analog
card and
network
cards
0x0418
for fiber
cards
(57600 N8-1)
0x0002
for all
cards
(Modbus
Rtu)
0x0000
63
write only in PS update
mode
One nibble for each input. 1
Assuming "abcc" as the bits
in each nibble:
"a": select this input for EOI
(End Of Interval)pulse
sensing.
"b": log this input when pulse
is detected
"cc": Input event trigger
mode - Contact sensing
method; 00 = none; 01 =
open to close; 10 = close to
open; 11 = any change.
Every input has an
associated internal
accumulator (See input
Accumulator Scaling), which
is incremented every time
the input changes according
with the trigger mode
crieteria “cc”
Delay to operate the relay 1
since request.
Delay to release the relay 1
since request.
Set to 0.
6
0x0000
(No EOI,
No Log,
No
change
detection)
0x000a
(1 second)
0x000a
(1 second)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7D09 - 7D09 32010 - 32010 Relay #2 Delay to UINT16
Operate
7D0A - 7D0A 32011 - 32011 Relay #2 Delay to UINT16
Release
7D0B - 7D20 32012 - 32033 Reserved
UINT16
0.1 second
units
0.1 second
units
Delay to operate the relay
since request.
Delay to release the relay
since request.
Set to 0.
7D21 - 7D21 32034 - 32034 Input
Accumulators
Scaling
UINT16
bit-mapped -------- 22221111
7D22 - 7D22 32035 - 32035 Relay
Accumulators
Scaling
UINT16
bit-mapped -------- 22221111
7D23 - 7D23 33036 - 33036 Fast pulse input
selector
UINT16
bit-mapped p------- -----nnn
4 bits per input or output 1
accumulator
The nibble informs what
should be the scaling of the
accumulator 0=no-scaling, 1
1=0.1, 2=0.01, 3= 1m,
4=0.1m, 5=0.01m, 6=1u,
7=0.1u; the value 15 disable
the accumulator.
Example: suppose that the
internal input accumulator
#1 is 12345, and its
corresponding scaling
setting is “0011” (3 decimal).
Then, the accumulator will
be read as:
Scaling 3, means 1m or
0.001.
Scaled accumulator = 12345
* 0.001 = 12 (Twelve).
When value 'nnn' is non1
zero, it determines which of
the card inputs will be a fast
pulse detection input.
The polarity bit 'P' tells the
event to be detected:
1=open-to-close; 0=closeto-open. There is no “anychange” detection mode.
Set to 0.
27
7D24 - 7D3E 32037 - 32063 Reserved
Block Size:
Settings Registers for Digital I/O Pulse Output Card
7D00 - 7D00 32001 - 32001 Input#1 - 4
UINT16
bindings & logging
enables
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
First Overlay
bit-mapped 44443333 22221111
1
1
22
0x000a
(1 second)
0x000a
(1 second)
0xFFFF
(accumul
ators
disabled)
0xFFFF
(accumul
ators
disabled)
Default is
0 (no fast
input
assigned)
63
write only in PS update
mode
One nibble for each input. 1
Assuming "abcc" as the bits
in each nibble:
"a": select this input for EOI
(End Of Interval)pulse
sensing.
"b": log this input when pulse
is detected
"cc": Input event trigger
mode - Contact sensing
method; 00 = none; 01 =
open to close; 10 = close to
open; 11 = any change.
Every input has an
associated internal
accumulator (See input
Accumulator Scaling), which
is incremented every time
the input changes according
with the trigger mode
crieteria “cc”
0x0000
(No EOI,
No Log,
No
change
detection)
B–69
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7D01 - 7D01 32002 - 32002 Source for Pulse
Ouput#1
UINT16
enumeration -----ppp ----vvvv
7D03 - 7D04 32004 - 32005 Output#2
UINT16
Assignment and Kt
same as Output #1
"ppp" (Phase) : 000 = none, 1
001 = Phase A, 010 = Phase
B, 011 = Phase C, 100 = All
Phases, 101 = Pulse from
EOI(End Of Interval).
"vvvv"(Value) :
0000= none,
0001 = Wh,
0010 = +Wh,
0011 = -Wh,
0100= Varh,
0101 = +Varh,
0110 = -Varh,
0111 = VAh,
1000= Received Wh,
1001= Delivered Wh,
1010= Inductive Varh,
1011 = Capacitive Varh
"V…V" = not scaled energy 1
value per pulse, from 0 to
9999.
"dd"= decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
2
7D02 - 7D02 32003 - 32003 Kt [Wh/pulse]
factor for Pulse
Output#1
UINT16
bit-mapped ddVVVVVV VVVVVVVV
7D05 - 7D06 32006 - 32007 Output#3
UINT16
Assignment and Kt
same as Output #1
2
7D07 - 7D08 32008 - 32009 Output#4
UINT16
Assignment and Kt
same as Output #1
2
7D09 - 7D09 32010 - 32010 Input
Accumulators
Scaling
7D0A - 7D0A 32011 - 32011 Output
Accumulators
Scaling
7D0B - 7D0B 32012 - 32012 Fast pulse input
selector
UINT16
bit-mapped 44443333 22221111
UINT16
bit-mapped 44443333 22221111
UINT16
bit-mapped p------- -----nnn
7D0C - 7D3E 32013 - 32063 Reserved
see Relay Card above
7D3F
- 7D46 32064 - 32071 Input#1 Label
Second Overlay
When value 'nnn' is non1
zero, it determines which of
the card inputs will be a fast
pulse detection input.
The polarity bit 'P' tells the
event to be detected:
1=open-to-close; 0=closeto-open. There is no “anychange” detection mode.
Reserved
51
write only in PS update
mode
16 char
7D47 - 7D4E 32072 - 32079 Input#1 Low State ASCII
Name
16 char
8
7D4F - 7D56 32080 - 32087 Input#1 High State ASCII
Name
16 char
8
B–70
0x0403 (Wh total)
0x4708
(1.800
Wh)
0x0405
(+VARh
total)
0x4708
(1.800
VARh)
0x0406 (VARh
total)
0x4708
(1.800
VARh)
Default is
0 (no fast
input
assigned)
63
ASCII
7D57 - 7D6E 32088 - 32111 Input#2 Label and same as Input#1
State Names
0x4708
(1.800
Wh)
1
Block Size:
Settings Registers for Digital I/O Relay Card
1
0x0402
(+Wh
total)
8
24
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7D6F - 7D9E 32112 - 32159 Reserved
Reserved
48
7D9F - 7DA6 32160 - 32167 Relay#1 Label
ASCII
16 char
8
7DA7 - 7DAE 32168 - 32175 Relay#1 Open
State Name
ASCII
16 char
8
7DAF - 7DB6 32176 - 32183 Relay#1 Closed
State Name
ASCII
16 char
8
7DB7 - 7DCE 32184 - 32207 Relay#2 Label and same as Relay#1
State Names
7DCF - 7DFE 32208 - 32255 Reserved
24
Reserved
48
7DFF - 7E06 32256 - 32263 Input#1
ASCII
Accumulator Label
16 char
8
7E07 - 7E0E 32264 - 32271 Input#2
ASCII
Accumulator Label
16 char
8
7E0F - 7E1E 32272 - 32287 Reserved
7E1F - 7E1F 32288 - 32288 Input#1
Accumulator Kt
7E20 - 7E20 32289 - 32289 Input#2
Accumulator Kt
Reserved
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
7E21 - 7F3E 32290 - 32575 Reserved
7D3F
- 7D46 32064 - 32071 Input#1 Label
Second Overlay
16
write only in PS update
mode
512
ASCII
16 char
7D47 - 7D4E 32072 - 32079 Input#1 Low State ASCII
Name
16 char
8
7D4F - 7D56 32080 - 32087 Input#1 High State ASCII
Name
16 char
8
8
7D57 - 7D6E 32088 - 32111 Input#2 Label and same as Input#1
State Names
24
7D6F - 7D86 32112 - 32135 Input#3 Label and same as Input#1
State Names
24
7D87 - 7D9E 32136 - 32159 Input#4 Label and same as Input#1
State Names
24
7D9F - 7DA6 32160 - 32167 Output#1 Label
ASCII
16 char
8
7DA7 - 7DAE 32168 - 32175 Output#1 Open
State Name
ASCII
16 char
8
7DAF - 7DB6 32176 - 32183 Output#1 Closed ASCII
State Name
16 char
8
7DB7 - 7DCE 32184 - 32207 Output#2 Label same as Output#1
and State Names
24
7DCF - 7DE6 32208 - 32231 Output#3 Label same as Output#1
and State Names
24
7DE7 - 7DFE 32232 - 32255 Output#4 Label same as Output#1
and State Names
24
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
16 spaces
(char
0x20)
16 spaces
(char
0x20)
KT power factor for the Pulse 1
Output
"V" is raw power value in
1
Wh/pulse from 0 to 9999.
"dd"=decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
Reserved
286
Block Size:
Settings Registers for Digital I/O Pulse Output Card
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
B–71
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7DFF - 7E06 32256 - 32263 Input#1
ASCII
Accumulator Label
16 char
8
7E07 - 7E0E 32264 - 32271 Input#2
ASCII
Accumulator Label
16 char
8
7E0F - 7E16 32272 - 32279 Input#3
ASCII
Accumulator Label
16 char
8
7E17 - 7E1E 32280 - 32287 Input#4
ASCII
Accumulator Label
16 char
8
7E1F - 7E1F 32288 - 32288 Input#1
Accumulator Kt
7E20 - 7E20 32289 - 32289 Input#2
Accumulator Kt
7E21 - 7E21 32290 - 32290 Input#3
Accumulator Kt
7E22 - 7E22 32291 - 32291 Input#4
Accumulator Kt
7E23 - 7F3E 32292 - 32575 Reserved
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
Settings Registers for Analog Out 0-1mA / Analog Out 4-20mA Cards
Second Overlay
7D3F
milliseconds
- 7D3F 32064 - 32064 Update rate
UINT16
0 to 65535
7D40 - 7D40 32065 - 32065 Channel direction - UINT16
1mA Card only!
bit-mapped -------- ----4321
7D41 - 7D41 32066 - 32066 Format parameter UINT16
for output #1
bit-mapped -------- ---f suwb
7D42 - 7D42 32067 - 32067 Source register for UINT16
Output#1
0 to 65535
7D43 - 7D44 32068 - 32069 High value of
Depends on the format parameter
source register for
output#1
7D45 - 7D46 32070 - 32071 Low value of
Depends on the format parameter
source register for
output#1
B–72
KT power factor for the
accumulator input
"V" is raw power value in
Wh/pulse from 0 to 9999.
"dd"=decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
1
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
1
1
1
Reserved
284
Block Size:
512
write only in PS update
mode
Fixed -- see specifications.
1
100 ms
Full range output for 0-1mA 1
card only: A bit set(1) means
full range (-1mA to +1mA); a
bit cleared(0) means source
only (0mA to +1mA).
Format of the polled
1
register:f=float 32; s=signed
32 bit int; u=unsigned 32 bit
int; w=signed 16 bit int;
b=unsigned 16 bit int.
This register should be
1
programmed with the
address of the register
whose value is to be used for
current output. In different
words, the current level
output of analog board will
follow the value of the
register addressed here.
Value read from the source 2
register at which High
nominal current will be
output. Example: for the 420mA card, if this register is
programmed with 750, then
the current output will be
20mA when the value read
from the source register is
750.
Value read from the source 2
register at which Low
nominal current will be
output. Example: for the 420mA card, if this register is
programmed with 0, then
the current output will be
4mA when the value read
from the source register is 0.
0x0003
(0-1)
0x0000
(4-20)
0x0010
(float)
0x03F9
(watts
total)
1800 W
-1800 W
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7D47 - 7D4C 32072 - 32077 Analog output#2 Same as analog output#1
format, register,
max & min
6
7D4D - 7D52 32078 - 32083 Analog output#3 Same as analog output#1
format, register,
max & min
6
7D53 - 7D58 32084 - 32089 Analog output#4 Same as analog output#1
format, register,
max & min
6
7D59 - 7F3E 32090 - 32575 Reserved
Settings Registers for Network Cards
7D3F
Second Overlay
- 7D3F 32064 - 32064 General Options
bit-mapped -------- ---s cwme
7D40 - 7D40 32065 - 32065 DHCP enable
bit-mapped -------- -------d
7D41 - 7D48 32066 - 32073 Host name label
ASCII
7D49 - 7D4C 32074 - 32077 IP card network
address
UINT16
Reserved
486
Block Size:
512
write only in PS update
mode
Servers enable(1) or
1
disable(0) flags:
s=Modbus_TCP_server;
c=Modbus_TCP_client;
w=Web server ; m=HTTP
Modbus RTU for diagnostics.
Sleep enabled e=0; sleep
disabled e=1.
DHCP: d=1 enabled, d=0
1
disabled (user must provide
IP configuration).
16 bytes (8 registers)
8
0 to 255
(IPv4)
These 4 registers hold the 4 4
numbers (1 number each
register) that make the IP
address used by the card.
7D4D - 7D4D 32078 - 32078 IP network address UINT16
mask length
0 to 32
7D4E - 7D51 32079 - 32082 IP card network UINT16
gateway address
0 to 255
(IPv4)
Number of bits that are set 1
in the IP address mask,
starting from the Msb of the
32 bit word.
Example 24 = 255.255.255.0;
a value of 2 would mean
192.0.0.0
These 4 registers hold the 4 4
numbers that make the IP
gateway address on
network.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
0x0010
(float)
0x03FB
(VAR total)
+1800
VAR
-1800
VAR
0x0010
(float)
WYE
DELTA
0x03E7
(Van)
0x03ED
(Vab)
300 V
600 V
0V
0V
0x0010
(float)
0x03F3
(Ia)
10 A
0A
0x000E
0x4531
3439
2020
2020
2020
2020
2020
2020
= E149
0x000A,
0x0000,
0x0000,
0x0002
= 10.0.0.2
0x00FF,
0x0000,
0x0000,
0x0000
=
255.0.0.0
0x000A,
0x0000,
0x0000,
0x0001
= 10.0.0.1
B–73
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
7D52 - 7D55 32083 - 32086 IP card network
DNS #1 address
UINT16
0 to 255
(IPv4)
IP address of the DNS#1 on 4
the network.
7D56 - 7D59 32087 - 32090 IP card network
DNS #2 address
UINT16
0 to 255
(IPv4)
IP address of the DNS#2 on 4
the network.
7D5A - 7E62 32091 - 32355 Reserved
7E63
- 7E63 32356 - 32356 FTP Client Flags
7E64
- 7E64 32357 - 32357 Reserved
7E65
- 7E84 32358 - 32389 FTP remote server ASCII or
address
UINT16
7E85
- 7E85 32390 - 32390 FTP remote port
UINT16
7E86
- 7EC5 32391 - 32454 FTP remote
directory
ASCII
128
characters
Remote directory where the 64
files to be retrieved are.
7EC6
- 7ED5 32455 - 32470 FTP remote
username
ASCII
32
characters
Username to access remote 16
FTP
7ED6 - 7EE5 32471 - 32485 FTP remote
password
ASCII
32
characters
Password to for previous
username account.
16
Set to 0
89
Block Size:
512
7EE6
bit-mapped -------- -----u-e
Write this with 0 to keep
265
future compatibility.
General FTP flags:
1
u: 0=FTP remote address is
an URL address; 1=FTP
remote address is an IP
address.
e: 0=FTP disabled;
1=Enabled.
Set to 0
1
The type of the data in these 32
registers depend on bit 'u' in
the FTP Client Flags register.
IP address (4 numbers) or
URL (64-characters) of the
FTP server
1
IP port of the remote FTP
server
- 7F3E 32486 - 32575 Reserved
0x0000,
0x0000,
0x0000,
0x0000 =
0.0.0.0
0x0000,
0x0000,
0x0000,
0x0000 =
0.0.0.0
0x0004
0
0x000a,0
x0000,0x
0000,0x0
004 =
10.0.0.4
0x0438 =
(1080
dec)
"Remote
directory"
with
trailing
nulls
"usernam
e" with
trailing
nulls
"passwor
d" with
trailing
nulls
PROGRAMMABLE SETTINGS FOR OPTION CARD 2
Option Card 2 Setups Block
write only in PS update
mode
80E7 - 80E7 33000 - 33000 Class ID of the
UINT16 bit-mapped -------- cccctttt
Which class (cccc) and
Option Card 2
type(tttt) of card the Option
Settings
Settings for Card 2 apply to.
See note 22
80E8 - 8126 33001 - 33063 Settings for Option Register assignments depend on which type of card is in the slot. See
Card 2, First
overlays below.
Overlay -- see
below
8127 - 8326 33064 - 33575 Settings for Option Register assignments depend on which type of card is in the slot. See
Card 2, Second
overlays below.
Overlay -- see
below
Block Size:
B–74
1
63
512
576
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
OVERLAYS FOR OPTION CARD 2 PROGRAMMABLE SETTINGS
Settings Registers for any communication capable card, including
First Overlay
network and analog cards
80E8 - 80E8 33001 - 33001 Slave address
UINT16 1~247 (for none
Modbus)
1~65534 (for
DNP)
write only in PS update
mode
Slave address of the unit.
1
The communication capable
card is always a master.
Set to 0 when an analog
board is installed.
80E9 - 80E9 33002 - 33002 Speed and format UINT16
bit-mapped -abcde--fghijklm
Bps: a=57600; b=38400;
1
c=19200; d=14400; e=9600
Stop bits 'f': cleared 1 stop
bit, set 2 stop bits
Parity: g=even; h=odd;
i=none
Data bits: j=8; k=7; l=6; m=5
Set to 0 when an analog
board is installed.
80EA - 80EA 33003 - 33003 Reserved
UINT16
bit-mapped
Reserved
80EB - 80EB 33004 - 33004 Protocol
UINT16
bit-mapped -------- -----ppp-
ppp= 100 =DNP3; 010=Ascii 1
Modbus; 001=Rtu Modbus
Set to 0 when an analog
board is installed.
80EC - 80EC 33005 - 33005 Reply delay
UINT16
0 to 65535
Delay to reply to a Modbus 1
transaction after receiving it.
Set to 0 when an analog
board is installed
Reserved
58
milliseconds
80ED - 8126 33006 - 33063 Reserved
Block Size:
Settings Registers for Digital I/O Relay Card
First Overlay
80E8 - 80E8 33001 - 33001 Input#1 - 2
UINT16
bindings & logging
enables
bit-mapped -------- 2222 1111
80E9 - 80E9 33002 - 33002 Relay #1 Delay to UINT16
Operate
80EA - 80EA 33003 - 33003 Relay #1 Delay to UINT16
Release
80EB - 80F0 33004 - 33009 Reserved
UINT16
0.1 second
units
0.1 second
units
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
1
0x0001
for
analog
and
network
cards
(non
configura
ble)
0x0001
Fiber
cards
Don't
care for
analog
card and
network
cards
0x0418
for fiber
cards
(57600 N8-1)
0x0002
for all
cards
(Modbus
Rtu)
0x0000
63
write only in PS update
mode
One nibble for each input. 1
Assuming "abcc" as the bits
in each nibble:
"a": select this input for EOI
(End Of Interval)pulse
sensing.
"b": log this input when pulse
is detected
"cc": Input event trigger
mode - Contact sensing
method; 00 = none; 01 =
open to close; 10 = close to
open; 11 = any change.
Every input has an
associated internal
accumulator (See input
Accumulator Scaling), which
is incremented every time
the input changes according
with the trigger mode
crieteria “cc”
Delay to operate the relay 1
since request.
Delay to release the relay 1
since request.
Set to 0.
6
0x0000
(No EOI,
No Log,
No
change
detection)
0x000a
(1 second)
0x000a
(1 second)
B–75
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
80F1 - 80F1 33010 - 33010 Relay #2 Delay to UINT16
Operate
80F2 - 80F2 33011 - 33011 Relay #2 Delay to UINT16
Release
80F3 - 8108 33012 - 33033 Reserved
UINT16
0.1 second
units
0.1 second
units
Delay to operate the relay
since request.
Delay to release the relay
since request.
Set to 0.
8109 - 8109 33034 - 33034 Input
Accumulators
Scaling
UINT16
bit-mapped -------- 22221111
810A - 810A 33035 - 33035 Relay
Accumulators
Scaling
UINT16
bit-mapped -------- 22221111
810B - 810B 33036 - 33036 Fast pulse input
selector
UINT16
bit-mapped p------- -----nnn
4 bits per input or output 1
accumulator
The nibble informs what
should be the scaling of the
accumulator 0=no-scaling, 1
1=0.1, 2=0.01, 3= 1m,
4=0.1m, 5=0.01m, 6=1u,
7=0.1u; the value 15 disable
the accumulator.
Example: suppose that the
internal input accumulator
#1 is 12345, and its
corresponding scaling
setting is “0011” (3 decimal).
Then, the accumulator will
be read as:
Scaling 3, means 1m or
0.001.
Scaled accumulator = 12345
* 0.001 = 12 (Twelve).
When value 'nnn' is non1
zero, it determines which of
the card inputs will be a fast
pulse detection input.
The polarity bit 'P' tells the
event to be detected:
1=open-to-close; 0=closeto-open. There is no “anychange” detection mode.
Reserved
27
810C - 8126 33037 - 33063 Reserved
Block Size:
Settings Registers for Digital I/O Pulse Output Card
80E8 - 80E8 33001 - 33001 Input#1 - 4
UINT16
bindings & logging
enables
B–76
First Overlay
bit-mapped 44443333 22221111
1
1
22
0x000a
(1 second)
0x000a
(1 second)
0xFFFF
(accumul
ators
disabled)
0xFFFF
(accumul
ators
disabled)
Default is
0 (no fast
input
assigned)
63
write only in PS update
mode
One nibble for each input. 1
Assuming "abcc" as the bits
in each nibble:
"a": select this input for EOI
(End Of Interval)pulse
sensing.
"b": log this input when pulse
is detected
"cc": Input event trigger
mode - Contact sensing
method; 00 = none; 01 =
open to close; 10 = close to
open; 11 = any change.
Every input has an
associated internal
accumulator (See input
Accumulator Scaling), which
is incremented every time
the input changes according
with the trigger mode
crieteria “cc”
0x0000
(No EOI,
No Log,
No
change
detection)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
80E9 - 80E9 33002 - 33002 Source for Pulse
Ouput#1
UINT16
enumeration -----ppp ----vvvv
80EB - 80EC 33004 - 33005 Output#2
UINT16
Assignment and Kt
same as Output #1
"ppp" (Phase) : 000 = none, 1
001 = Phase A, 010 = Phase
B, 011 = Phase C, 100 = All
Phases, 101 = Pulse from
EOI(End Of Interval).
"vvvv"(Value) :
0000= none,
0001 = Wh,
0010 = +Wh,
0011 = -Wh,
0100= Varh,
0101 = +Varh,
0110 = -Varh,
0111 = VAh,
1000= Received Wh,
1001= Delivered Wh,
1010= Inductive Varh,
1011 = Capacitive Varh
"V…V" = not scaled energy 1
value per pulse, from 0 to
9999.
"dd"= decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
2
80EA - 80EA 33003 - 33003 Kt [Wh/pulse]
factor for Pulse
Output#1
UINT16
bit-mapped ddVVVVVV VVVVVVVV
80ED - 80EE 33006 - 33007 Output#3
UINT16
Assignment and Kt
same as Output #1
2
80EF - 80F0 33008 - 33009 Output#4
UINT16
Assignment and Kt
same as Output #1
2
80F1 - 80F1 33010 - 33010 Input
Accumulators
Scaling
80F2 - 80F2 33011 - 33011 Output
Accumulators
Scaling
80F3 - 80F3 33012 - 33012 Fast pulse input
selector
UINT16
bit-mapped 44443333 22221111
UINT16
bit-mapped 44443333 22221111
UINT16
bit-mapped p------- -----nnn
80F4 - 8126 33013 - 33063 Reserved
see Relay Card above
8127 - 812E 33064 - 33071 Input#1 Label
Second Overlay
When value 'nnn' is non1
zero, it determines which of
the card inputs will be a fast
pulse detection input.
The polarity bit 'P' tells the
event to be detected:
1=open-to-close; 0=closeto-open. There is no “anychange” detection mode.
Reserved
51
write only in PS update
mode
16 char
812F - 8136 33072 - 33079 Input#1 Low State ASCII
Name
16 char
8
8137 - 813E 33080 - 33087 Input#1 High State ASCII
Name
16 char
8
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
0x0403 (Wh total)
0x4708
(1.800
Wh)
0x0405
(+VARh
total)
0x4708
(1.800
VARh)
0x0406 (VARh
total)
0x4708
(1.800
VARh)
Default is
0 (no fast
input
assigned)
63
ASCII
813F - 8156 33088 - 33111 Input#2 Label and same as Input#1
State Names
0x4708
(1.800
Wh)
1
Block Size:
Settings Registers for Digital I/O Relay Card
1
0x0402
(+Wh
total)
8
24
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
B–77
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
8157 - 8186 33112 - 33159 Reserved
48
8187 - 818E 33160 - 33167 Relay#1 Label
ASCII
16 char
8
818F - 8196 33168 - 33175 Relay#1 Open
State Name
ASCII
16 char
8
8197 - 819E 33176 - 33183 Relay#1 Closed
State Name
ASCII
16 char
8
819F - 81B6 33184 - 33207 Relay#2 Label and same as Relay#1
State Names
81B7 - 81E6 33208 - 33255 Reserved
24
81E7 - 81EE 33256 - 33263 Input#1
ASCII
Accumulator Label
16 char
8
81EF - 81F6 33264 - 33271 Input#2
ASCII
Accumulator Label
16 char
8
8208 - 8208 33289 - 33289 Input#2
Accumulator Kt
bit-mapped ddVVVVVV VVVVVVVV
1
UINT16
48
8209 - 8326 33290 - 33575 Reserved
Settings Registers for Digital I/O Pulse Output Card
Second Overlay
write only in PS update
mode
512
ASCII
16 char
812F - 8136 33072 - 33079 Input#1 Low State ASCII
Name
16 char
8
8137 - 813E 33080 - 33087 Input#1 High State ASCII
Name
16 char
8
8
813F - 8156 33088 - 33111 Input#2 Label and same as Input#1
State Names
24
8157 - 816E 33112 - 33135 Input#3 Label and same as Input#1
State Names
24
816F - 8186 33136 - 33159 Input#4 Label and same as Input#1
State Names
24
8187 - 818E 33160 - 33167 Output#1 Label
ASCII
16 char
8
818F - 8196 33168 - 33175 Output#1 Open
State Name
ASCII
16 char
8
8197 - 819E 33176 - 33183 Output#1 Closed ASCII
State Name
16 char
8
819F - 81B6 33184 - 33207 Output#2 Label same as Output#1
and State Names
24
81B7 - 81CE 33208 - 33231 Output#3 Label same as Output#1
and State Names
24
81CF - 81E6 33232 - 33255 Output#4 Label same as Output#1
and State Names
24
B–78
16 spaces
(char
0x20)
16 spaces
(char
0x20)
286
Block Size:
8127 - 812E 33064 - 33071 Input#1 Label
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
81E7 - 81EE 33256 - 33263 Input#1
ASCII
Accumulator Label
16 char
8
81EF - 81F6 33264 - 33271 Input#2
ASCII
Accumulator Label
16 char
8
81F7 - 81FE 33272 - 33279 Input#3
ASCII
Accumulator Label
16 char
8
81FF - 8206 33280 - 33287 Input#4
ASCII
Accumulator Label
16 char
8
8207 - 8207 33288 - 33288 Input#1
Accumulator Kt
8208 - 8208 33289 - 33289 Input#2
Accumulator Kt
8209 - 8209 33290 - 33290 Input#3
Accumulator Kt
820A - 820A 33291 - 33291 Input#4
Accumulator Kt
820B - 8326 33292 - 33575 Reserved
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
UINT16
bit-mapped ddVVVVVV VVVVVVVV
Settings Registers for Analog Out 0-1mA / Analog Out 4-20mA Cards
Second Overlay
8127 - 8127 33064 - 33064 Update rate
milliseconds
UINT16
0 to 65535
8128 - 8128 33065 - 33065 Channel direction - UINT16
1mA Card only!
bit-mapped -------- ----4321
8129 - 8129 33066 - 33066 Format parameter UINT16
for output #1
bit-mapped -------- ---f suwb
812A - 812A 33067 - 33067 Source register for UINT16
Output#1
0 to 65535
812B - 812C 33068 - 33069 High value of
Depends on the format parameter
source register for
output#1
812D - 812E 33070 - 33071 Low value of
Depends on the format parameter
source register for
output#1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
KT power factor for the
accumulator input
"V" is raw power value in
Wh/pulse from 0 to 9999.
"dd"=decimal point position:
00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
16 spaces
(char
0x20)
1
1
1
1
Reserved
284
Block Size:
512
write only in PS update
mode
Fixed -- see specifications.
1
100 ms
Full range output for 0-1mA 1
card only: A bit set(1) means
full range (-1mA to +1mA); a
bit cleared(0) means source
only (0mA to +1mA).
Format of the polled
1
register:f=float 32; s=signed
32 bit int; u=unsigned 32 bit
int; w=signed 16 bit int;
b=unsigned 16 bit int.
This register should be
1
programmed with the
address of the register
whose value is to be used for
current output. In different
words, the current level
output of analog board will
follow the value of the
register addressed here.
Value read from the source 2
register at which High
nominal current will be
output. Example: for the 420mA card, if this register is
programmed with 750, then
the current output will be
20mA when the value read
from the source register is
750.
Value read from the source 2
register at which Low
nominal current will be
output. Example: for the 420mA card, if this register is
programmed with 0, then
the current output will be
4mA when the value read
from the source register is 0.
0x0003
(0-1)
0x0000
(4-20)
0x0010
(float)
0x03F9
(watts
total)
1800 W
-1800 W
B–79
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
812F - 8134 33072 - 33077 Analog output#2 Same as analog output#1
format, register,
max & min
6
8135 - 813A 33078 - 33083 Analog output#3 Same as analog output#1
format, register,
max & min
6
813B - 8140 33084 - 33089 Analog output#4 Same as analog output#1
format, register,
max & min
6
8141 - 8326 33090 - 33575 Reserved
Settings Registers for Network Cards
Second Overlay
8127 - 8127 33064 - 33064 General Options
bit-mapped -------- ---s cwme
8128 - 8128 33065 - 33065 DHCP enable
bit-mapped -------- -------d
8129 - 8130 33066 - 33073 Host name label
ASCII
8131 - 8134 33074 - 33077 IP card network
address
UINT16
Reserved
486
Block Size:
512
write only in PS update
mode
Servers enable(1) or
1
disable(0) flags:
s=Modbus_TCP_server;
c=Modbus_TCP_client;
w=Web server ; m=HTTP
Modbus RTU for diagnostics.
Sleep enabled e=0; sleep
disabled e=1.
DHCP: d=1 enabled, d=0
1
disabled (user must provide
IP configuration).
16 bytes (8 registers)
8
0 to 255
(IPv4)
These 4 registers hold the 4 4
numbers (1 number each
register) that make the IP
address used by the card.
8135 - 8135 33078 - 33078 IP network address UINT16
mask length
0 to 32
8136 - 8139 33079 - 33082 IP card network UINT16
gateway address
0 to 255
(IPv4)
Number of bits that are set 1
in the IP address mask,
starting from the Msb of the
32 bit word.
Example 24 = 255.255.255.0;
a value of 2 would mean
192.0.0.0
These 4 registers hold the 4 4
numbers that make the IP
gateway address on
network.
B–80
0x0010
(float)
0x03FB
(VAR total)
+1800
VAR
-1800
VAR
0x0010
(float)
WYE
DELTA
0x03E7
(Van)
0x03ED
(Vab)
300 V
600 V
0V
0V
0x0010
(float)
0x03F3
(Ia)
10 A
0A
0x000E
0x4531
3439
2020
2020
2020
2020
2020
2020
= E149
0x000A,
0x0000,
0x0000,
0x0002
= 10.0.0.2
0x00FF,
0x0000,
0x0000,
0x0000
=
255.0.0.0
0x000A,
0x0000,
0x0000,
0x0001
= 10.0.0.1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
813A - 813D 33083 - 33086 IP card network
DNS #1 address
UINT16
0 to 255
(IPv4)
IP address of the DNS#1 on 4
the network.
813E - 8141 33087 - 33090 IP card network
DNS #2 address
UINT16
0 to 255
(IPv4)
IP address of the DNS#2 on 4
the network.
8142 - 824A 33091 - 33355 Reserved
824B - 824B 33356 - 33356 FTP Client Flags
bit-mapped -------- -----u-e
824C - 824C 33357 - 33357 Reserved
824D - 826C 33358 - 33389 FTP remote server ASCII or
address
UINT16
Write this with 0 to keep
265
future compatibility.
General FTP flags:
1
u: 0=FTP remote address is
an URL address; 1=FTP
remote address is an IP
address.
e: 0=FTP disabled;
1=Enabled.
Reserved
1
The type of the data in these 32
registers depend on bit 'u' in
the FTP Client Flags register.
IP address (4 numbers) or
URL (64-characters) of the
FTP server
IP port of the remote FTP
1
server
0x0004
0
0x000a,0
x0000,0x
0000,0x0
004 =
10.0.0.4
826D - 826D 33390 - 33390 FTP remote port
UINT16
826E - 82AD 33391 - 33454 FTP remote
directory
ASCII
128
characters
Remote directory where the 64
files to be retrieved are.
82AE - 82BD 33455 - 33470 FTP remote
username
ASCII
32
characters
Username to access remote 16
FTP
82BE - 82CC 33471 - 33485 FTP remote
password
ASCII
32
characters
Password to for previous
username account.
16
Reserved
89
Block Size:
512
82CD - 8326 33486 - 33575 Reserved
0x0000,
0x0000,
0x0000,
0x0000 =
0.0.0.0
0x0000,
0x0000,
0x0000,
0x0000 =
0.0.0.0
0x0438 =
(1080
dec)
"Remote
directory"
with
trailing
nulls
"usernam
e" with
trailing
nulls
"passwor
d" with
trailing
nulls
SECONDARY READINGS SECTION
Secondary Block
read-only except as noted
9C40 - 9C40 40001 - 40001 System Sanity
Indicator
9C41 - 9C41 40002 - 40002 Volts A-N
UINT16
0 or 1
UINT16
2047 to 4095 volts
9C42 - 9C42 40003 - 40003 Volts B-N
UINT16
2047 to 4095 volts
9C43 - 9C43 40004 - 40004 Volts C-N
UINT16
2047 to 4095 volts
volts = 150 * (register - 2047) 1
/ 2047
1
9C44 - 9C44 40005 - 40005 Amps A
UINT16
0 to 4095
amps
0= -10, 2047= 0, 4095= +10 1
9C45 - 9C45 40006 - 40006 Amps B
UINT16
0 to 4095
amps
9C46 - 9C46 40007 - 40007 Amps C
UINT16
0 to 4095
amps
amps = 10 * (register - 2047) 1
/ 2047
1
9C47 - 9C47 40008 - 40008 Watts, 3-Ph total UINT16
0 to 4095
watts
9C48 - 9C48 40009 - 40009 VARs, 3-Ph total
UINT16
0 to 4095
VARs
9C49 - 9C49 40010 - 40010 VAs, 3-Ph total
UINT16
2047 to 4095 VAs
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
none
0 indicates proper meter
operation
2047= 0, 4095= +150
1
1
0= -3000, 2047= 0, 4095=
+3000
watts, VARs, VAs =
1
3000 * (register - 2047) /
2047
1
1
B–81
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
9C4A - 9C4A 40011 - 40011 Power Factor, 3-Ph UINT16
total
1047 to 3047 none
9C4B - 9C4B 40012 - 40012 Frequency
UINT16
0 to 2730
9C4C - 9C4C 40013 - 40013 Volts A-B
UINT16
2047 to 4095 volts
9C4D - 9C4D 40014 - 40014 Volts B-C
UINT16
2047 to 4095 volts
9C4E - 9C4E 40015 - 40015 Volts C-A
UINT16
2047 to 4095 volts
9C4F - 9C4F 40016 - 40016 CT numerator
UINT16
1 to 9999
none
9C50 - 9C50 40017 - 40017 CT multiplier
UINT16
1, 10, 100
none
CT = numerator * multiplier / 1
denominator
1
9C51 - 9C51 40018 - 40018 CT denominator
UINT16
1 or 5
none
1
9C52 - 9C52 40019 - 40019 PT numerator
UINT16
1 to 9999
none
9C53 - 9C53 40020 - 40020 PT multiplier
UINT16
none
9C54 - 9C54 40021 - 40021 PT denominator
UINT16
1, 10, 100,
1000
1 to 9999
PT = numerator * multiplier / 1
denominator
1
none
1
Wh per energy format * 5 to 8 digits
2
9C55 - 9C56 40022 - 40023 W-hours, Positive UINT32
1047= -1, 2047= 0, 3047= +1 1
pf = (register - 2047) /
1000
0= 45 or less, 2047= 60,
1
2730= 65 or more
freq = 45 + ((register / 4095) *
30)
2047= 0, 4095= +300
1
Hz
volts = 300 * (register - 2047) 1
/ 2047
1
9C7D - 9C7D 40062 - 40062 Watts, Phase A
UINT16
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to
99999999
0 to 4095
9C7E - 9C7E 40063 - 40063 Watts, Phase B
UINT16
0 to 4095
watts
1
9C7F - 9C7F 40064 - 40064 Watts, Phase C
UINT16
0 to 4095
watts
1
9C57 - 9C58 40024 - 40025 W-hours, Negative UINT32
9C59 - 9C5A 40026 - 40027 VAR-hours,
Positive
9C5B - 9C5C 40028 - 40029 VAR-hours,
Negative
9C5D - 9C5E 40030 - 40031 VA-hours
UINT32
UINT32
UINT32
9C5F - 9C60 40032 - 40033 W-hours, Positive, UINT32
Phase A
9C61 - 9C62 40034 - 40035 W-hours, Positive, UINT32
Phase B
9C63 - 9C64 40036 - 40037 W-hours, Positive, UINT32
Phase C
9C65 - 9C66 40038 - 40039 W-hours,
UINT32
Negative, Phase A
9C67 - 9C68 40040 - 40041 W-hours,
UINT32
Negative, Phase B
9C69 - 9C6A 40042 - 40043 W-hours,
UINT32
Negative, Phase C
9C6B - 9C6C 40044 - 40045 VAR-hours,
UINT32
Positive, Phase A
9C6D - 9C6E 40046 - 40047 VAR-hours,
UINT32
Positive, Phase B
9C6F - 9C70 40048 - 40049 VAR-hours,
UINT32
Positive, Phase C
9C71 - 9C72 40050 - 40051 VAR-hours,
UINT32
Negative, Phase A
9C73 - 9C74 40052 - 40053 VAR-hours,
UINT32
Negative, Phase B
9C75 - 9C76 40054 - 40055 VAR-hours,
UINT32
Negative, Phase C
9C77 - 9C78 40056 - 40057 VA-hours, Phase A UINT32
9C79 - 9C7A 40058 - 40059 VA-hours, Phase B UINT32
9C7B - 9C7C 40060 - 40061 VA-hours, Phase C UINT32
B–82
Wh per energy format * decimal point implied, per 2
energy format
VARh per energy format * resolution of digit before 2
decimal point = units, kilo, or
VARh per energy format mega, per energy format
2
VAh per energy format * see note 10
2
Wh per energy format
2
Wh per energy format
2
Wh per energy format
2
Wh per energy format
2
Wh per energy format
2
Wh per energy format
2
VARh per energy format
2
VARh per energy format
2
VARh per energy format
2
VARh per energy format
2
VARh per energy format
2
VARh per energy format
2
VAh per energy format
2
VAh per energy format
2
VAh per energy format
2
watts
1
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
9C80 - 9C80 40065 - 40065 VARs, Phase A
UINT16
0 to 4095
VARs
9C81 - 9C81 40066 - 40066 VARs, Phase B
UINT16
0 to 4095
VARs
9C82 - 9C82 40067 - 40067 VARs, Phase C
UINT16
0 to 4095
VARs
9C83 - 9C83 40068 - 40068 VAs, Phase A
UINT16
2047 to 4095 VAs
9C84 - 9C84 40069 - 40069 VAs, Phase B
UINT16
2047 to 4095 VAs
1
9C85 - 9C85 40070 - 40070 VAs, Phase C
UINT16
2047 to 4095 VAs
1
9C86 - 9C86 40071 - 40071 Power Factor,
Phase A
9C87 - 9C87 40072 - 40072 Power Factor,
Phase B
9C88 - 9C88 40073 - 40073 Power Factor,
Phase C
9C89 - 9CA2 40074 - 40099 Reserved
UINT16
1047 to 3047 none
UINT16
1047 to 3047 none
1047= -1, 2047= 0, 3047= +1 1
pf = (register - 2047) /
1000
1
UINT16
1047 to 3047 none
1
N/A
N/A
UINT16
password
(Note 5)
9CA3 - 9CA3 40100 - 40100 Reset Energy
Accumulators
none
0= -3000, 2047= 0, 4095=
+3000
watts, VARs, VAs =
1
3000 * (register - 2047) /
2047
1
1
1
Reserved
26
write-only register; always
reads as 0
Block Size:
1
100
LOG RETRIEVAL SECTION
Log Retrieval Block
read/write except as noted
C34C - C34D 49997 - 49998 Log Retrieval
UINT32
Session Duration
C34E - C34E 49999 - 49999 Log Retrieval
UINT16
Session Com Port
0 to
4 msec
4294967294
0 to 4
C34F - C34F 50000 - 50000 Log Number,
Enable, Scope
bit-mapped nnnnnnnn esssssss
UINT16
C350 - C350 50001 - 50001 Records per
UINT16
Window or Batch,
Record Scope
Selector, Number
of Repeats
bit-mapped wwwwwwww
snnnnnnn
C351 - C352 50002 - 50003 Offset of First
UINT32
Record in Window
bit-mapped ssssssss nnnnnnnn
nnnnnnnn nnnnnnnn
C353 - C3CD 50004 - 50126 Log Retrieve
Window
see
comments
UINT16
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
none
0 if no session active; wraps 2
around after max count
0 if no session active, 1-4 for 1
session active on COM1 COM4
high byte is the log number 1
(0-system, 1-alarm, 2history1, 3-history2, 4history3, 5-I/O changes, 10PQ, 11-waveform
e is retrieval session
enable(1) or disable(0)
sssssss is what to retrieve (0normal record, 1timestamps only, 2complete memory image (no
data validation if image)
high byte is records per
1
window if s=0 or records per
batch if s=1, low byte is
number of repeats for
function 35 or 0 to suppress
auto-incrementing; max
number of repeats is 8 (RTU)
or 4 (ASCII) total windows, a
batch is all the windows
ssssssss is window status (0 2
to 7-window number, 0xFFnot ready); this byte is readonly.
nn…nn is a 24-bit record
number. The log's first
record is latched as a
reference point when the
session is enabled. This
offset is a record index
relative to that point. Value
provided is the relative index
of the whole or partial
record that begins the
window.
mapped per record layout 123
and retrieval scope, readonly
B–83
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Block Size:
Log Status Block
read only
Alarm Log Status
Block
C737 - C738 51000 - 51001 Log Size in RecordsUINT32
0 to
record
4,294,967,29
4
1 to
record
4,294,967,29
4
14 to 242
byte
C739 - C73A 51002 - 51003 Number of
Records Used
UINT32
C73B - C73B 51004 - 51004 Record Size in
Bytes
C73C - C73C 51005 - 51005 Log Availability
UINT16
C73D - C73F 51006 - 51008 Timestamp, First
Record
C740 - C742 51009 - 51011 Timestamp, Last
Record
C743 - C746 51012 - 51015 Reserved
TSTAMP 1Jan2000 - 1 sec
31Dec2099
TSTAMP 1Jan2000 - 1 sec
31Dec2099
C747 - C756 51016 - 51031 System Log Status
Block
C757 - C766 51032 - 51047 Historical Log 1
Status Block
C767 - C776 51048 - 51063 Historical Log 2
Status Block
C777 - C786 51064 - 51079 Historical Log 3
Status Block
C787 - C796 51080 - 51095 I/O Change Log
Status Block
C797 - C7A6 51096 - 51111 Power Quality Log
Status Block
C7A7 - C7B6 51112 - 51127 Waveform Capture
Log Status Block
B–84
130
UINT16
none
2
2
1
0=available,
1-4=in use by COM1-4,
0xFFFF=not available (log
size=0)
1
3
3
Reserved
4
same as alarm log status block
Individual Log Status Block 16
Size:
16
same as alarm log status block
16
same as alarm log status block
16
same as alarm log status block
16
same as alarm log status block
16
same as alarm log status block
16
same as alarm log status block
16
Block Size:
128
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
Data Formats
ASCII
SINT16 / UINT16
ASCII characters packed 2 per register in high, low order and without any termination characters. For example,
"EPM7000" would be 4 registers containing 0x5378, 0x6172, 0x6B32, 0x3030.
16-bit signed / unsigned integer.
32-bit signed / unsigned integer spanning 2 registers. The lower-addressed register is the high order half.
32-bit IEEE floating point number spanning 2 registers. The lower-addressed register is the high order half (i.e.,
contains the exponent).
3 adjacent registers, 2 bytes each. First (lowest-addressed) register high byte is year (0-99), low byte is month (112). Middle register high byte is day(1-31), low byte is hour (0-23 plus DST bit). DST (daylight saving time) bit is bit
6 (0x40). Third register high byte is minutes (0-59), low byte is seconds (0-59). For example, 9:35:07AM on October
12, 2049 would be 0x310A, 0x0C49, 0x2307, assuming DST is in effect.
Notes
1
2
3
4
5
6
7
All registers not explicitly listed in the table read as 0. Writes to these registers will be accepted but won't actually change the
register (since it doesn't exist).
Meter Data Section items read as 0 until first readings are available or if the meter is not in operating mode. Writes to these
registers will be accepted but won't actually change the register.
Register valid only in programmable settings update mode. In other modes these registers read as 0 and return an illegal
data address exception if a write is attempted.
Meter command registers always read as 0. They may be written only when the meter is in a suitable mode. The registers
return an illegal data address exception if a write is attempted in an incorrect mode.
If the password is incorrect, a valid response is returned but the command is not executed. Use 5555 for the password if
passwords are disabled in the programmable settings.
M denotes a 1,000,000 multiplier.
9
Each identifier is a Modbus register. For entities that occupy multiple registers (FLOAT, SINT32, etc.) all registers making up the
entity must be listed, in ascending order. For example, to log phase A volts, VAs, voltage THD, and VA hours, the register list
would be 0x3E7, 0x3E8, 0x411, 0x412, 0x176F, 0x61D, 0x61E and the number of registers (0x7917 high byte) would be 7.
Writing this register causes data to be saved permanently in nonvolatile memory. Reply to the command indicates that it was
accepted but not whether or not the save was successful. This can only be determined after the meter has restarted.
Reset commands make no sense if the meter state is LIMP. An illegal function exception will be returned.
10
Energy registers should be reset after a format change.
11
Entities to be monitored against limits are identified by Modbus address. Entities occupying multiple Modbus registers, such
as floating point values, are identified by the lower register address. If any of the 8 limits is unused, set its identifier to zero. If
the indicated Modbus register is not used or is a nonsensical entity for limits, it will behave as an unused limit.
There are 2 setpoints per limit, one above and one below the expected range of values. LM1 is the "too high" limit, LM2 is "too
low". The entity goes "out of limit" on LM1 when its value is greater than the setpoint. It remains "out of limit" until the value
drops below the in threshold. LM2 works similarly, in the opposite direction. If limits in only one direction are of interest, set
the in threshold on the "wrong" side of the setpoint. Limits are specified as % of full scale, where full scale is automatically set
appropriately for the entity being monitored:
current
FS = CT numerator
* CT multiplier
voltage
FS = PT numerator
* PT multiplier
3 phase power FS = CT numerator * CT multiplier * PT numerator * PT multiplier * 3
[ * SQRT(3) for delta hookup]
single phase
FS = CT numerator * CT multiplier * PT numerator * PT multiplier [ *
power
SQRT(3) for delta hookup]
frequency
FS = 60 (or 50)
frequency
power factor FS = 1.0
power factor
percentage
FS = 100.0
percentage
angle
FS = 180.0
angle
THD not available shows 10000 in all THD and harmonic magnitude and phase registers for the channel. THD may be
unavailable due to low V or I amplitude, delta hookup (V only), or Software Option setting.
Option Card Identification and Configuration Block is an image of the EEPROM on the card
8
12
13
14
15
A block of data and control registers is allocated for each option slot. Interpretation of the register data depends on what
card is in the slot.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
B–85
APPENDIX B: MODBUS MAP AND RETRIEVING LOGS
16
17
18
19
20
21
22
Measurement states: Off occurs during programmable settings updates; Run is the normal measuring state; Limp indicates
that an essentail non-volatile memory block is corrupted; and Warmup occurs briefly (approximately 4 seconds) at startup
while the readings stabilize. Run state is required for measurement, historical logging, demand interval processing, limit
alarm evaluation, min/max comparisons, and THD calculations. Resetting min/max or energy is allowed only in run and off
states; warmup will return a busy exception. In limp state, the meter reboots at 5 minute intervals in an effort to clear the
problem.
Limits evaluation for all entites except demand averages commences immediately after the warmup period. Evaluation for
demand averages, maximum demands, and minimum demands commences at the end of the first demand interval after
startup.
Autoincrementing and function 35 must be used when retrieving waveform logs.
Depending on the Option selected, there are 15, 29, or 45 flash sectors available in a common pool for distribution among the
3 historical and waveform logs. The pool size, number of sectors for each log, and the number of registers per record together
determine the maximum number of records a log can hold.
S = number of sectors assigned to the log,
H = number of Modbus registers to be monitored in each historical record (up to 117),
R = number of bytes per record = (12 + 2H) for historical logs
N = number of records per sector = 65516 / R, rounded down to an integer value (no partial records in a sector)
T = total number of records the log can hold = S * N
T = S * 2 for the waveform log.
Only 1 input on all digital input cards may be specified as the end-of-interval pulse.
Logs cannot be reset during log retrieval. Waveform log cannot be reset while storing a capture. Busy exception will be
returned.
Combination of class and type currently defined are:
0x23 = Fiber cards
0x24 = Network card
0x41 = Relay card
0x42 = Pulse card
0x81 = 0-1mA analog output card
0x82 = 4-20mA analog output card.
B–86
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Appendix C: DNP Mapping
DNP Mapping
C.1
Overview
This Appendix describes the functionality of the EPM7000 meter's version of the DNP
protocol. A DNP programmer must follow this information in order to retrieve data from the
EPM7000 meter. The DNP used by the EPM7000 is a reduced set of the Distributed Network
Protocol Version 3.0 subset 2; it gives enough functionality to get critical measurements
from the EPM7000 meter.
The EPM7000 meter's DNP version supports Class 0 object/qualifiers 0,1,2,6, only. No event
generation is supported. The EPM7000 meter always acts as a secondary device (slave) in
DNP communication.
A new feature allows DNP readings in primary units with user-set scaling for current,
voltage, and power. (See Chapter 5 in the GE Communicator EXT User Manual for
instructions.)
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
C–1
APPENDIX C: DNP MAPPING
C.2
Physical Layer
The EPM7000 meter's DNP version uses serial communication. It can be assigned to Port 2
(RS485 compliant port) or any communication capable option board. Speed and data
format is transparent for the EPM7000 meter's DNP version: they can be set to any
supported value. The IrDA port cannot use the EPM7000 meter's DNP version.
C–2
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX C: DNP MAPPING
C.3
Data Link Layer
The EPM7000 meter can be assigned with a value from 1 to 65534 as the target device
address. The data link layer follows the standard frame FT3 used by the DNP Version 3.0
protocol, but only 4 functions are implemented: Reset Link, Reset User, Unconfirmed User
Data, and Link Status, as depicted in the following table.
Table C–1: Supported Link Functions
Function
Function Code
Reset Link
0
Reset User
1
Unconfirmed User Data
4
Link Status
9
[dst] and [src] are the device address of the EPM7000 Meter and Master device,
respectively. Refer to Section C.7 for more detail on supported frames for the data link
layer.
In order to establish a clean communication with the EPM7000 meter, we recommended
you perform the Reset Link and Reset User functions. The Link Status is not mandatory but
if queried it will be attended to. The inter-character time-out for the EPM7000 meter's DNP
version is 1 second. If this amount of time, or more, elapses between two consecutive
characters within a FT3 frame, the frame will be dropped.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
C–3
APPENDIX C: DNP MAPPING
C.4
Application Layer
In the EPM7000 meter, the EPM7000 meter's DNP version supports the Read function,
Write Function, the Direct Operate function and the Direct Operate Unconfirmed function.
• The Read function (code 01) provides a means for reading the critical
measurement data from the meter. This function should be posted to read object
60 variation 1, which will read all the available Class 0 objects from the register
map of the EPM7000 meter's DNP version. See register map in Section C.6. In order
to retrieve all objects with their respective variations, the qualifier must be set to
ALL (0x06). See Section C.7 for an example showing a read Class 0 request data
from the meter.
• The Write function (code 02) provides a mean for clearing the Device restart bit in
the Internal Indicator register only. This is mapped to Object 80, point 0 with
variation 1. When clearing the restart device indicator use qualifier 0. Section C.7
shows the supported frames for this function.
• The Direct Operate function (code 05) is intended for resetting the energy counters
and the demand counters (minimum and maximum energy registers). These
actions are mapped to Object 12, point 0 and point 2, that are seen as a control
relay. The relay must be operated (On) in 0 msec and released (Off) in 1 msec only.
Qualifiers 0x17 or x28 are supported for writing the energy reset. Sample frames
are shown in Section C.7.
• The Direct Operate Unconfirmed (or Unacknowledged) function (code 06) is
intended for asking the communication port to switch to Modbus RTU protocol
from the EPM7000 meter's DNP version. This switching is seen as a control relay
mapped into Object 12, point 1 in the meter. The relay must be operated with
qualifier 0x17, code 3 count 0, with 0 millisecond on and 1 millisecond off, only.
After sending this request the current communication port will accept Modbus RTU
frames only. To make this port go back to DNP protocol, the unit must be powerrecycled. Section C.7 shows the constructed frame to perform DNP to Modbus RTU
protocol change.
C–4
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX C: DNP MAPPING
C.5
Error Reply
In the case of an unsupported function, or any other recognizable error, an error reply will
be generated from the EPM7000 meter to the Primary station (the requester). The Internal
Indicator field will report the type of error: unsupported function or bad parameter.
The broadcast acknowledge and restart bit, are also signaled in the internal indicator but
they do not indicate an error condition.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
C–5
APPENDIX C: DNP MAPPING
C.6
The Register Map for the EPM7000 Meter’s DNP Version
Table C–2: Object 10 - Binary Output States
Object
Point
Var
Description
Format
Range
10
0
2
Reset Energy
Counters
BYTE
Always 1
10
1
2
Change to
Modbus RTU
Protocol
BYTE
10
2
2
Reset Demand
Cntrs (Max / Min )
BYTE
Multiplier
Units
Comments
N/A
None
Read by Class 0
or with qualifier
0, 1, 2, or 6
Always 1
N/A
None
Read by Class 0
or with qualifier
0, 1, 2, or 6
Always 1
N/A
None
Read by Class 0
or with qualifier
0, 1, 2, or 6
Table C–3: Object 12 - Control Relay Outputs
C–6
Object
Point
Var
12
0
1
12
1
12
2
Description
Format
Range
Multiplier
Units
Comments
Reset Energy
Counters
N/A
N/A
N/A
none
Responds to Function 5
(Direct Operate), Qualifier
Code 17x or 28x, Control
Code 3, Count 0, On 0 msec,
Off 1 msec ONLY.
1
Change to
Modbus RTU
Protocol
N/A
N/A
N/A
none
Responds to Function 6
(Direct Operate - No Ack),
Qualifier Code 17x, Control
Code 3, Count 0, On 0 msec,
Off 1 msec ONLY.
1
Reset Demand
Counters (Max /
Min)
N/A
N/A
N/A
none
Responds to Function 5
(Direct Operate), Qualifier
Code 17x or 28x, Control
Code 3, Count 0, On 0 msec,
Off 1 msec ONLY.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX C: DNP MAPPING
Table C–4: Object 20 - Binary Counters (Primary Readings) - Read via Class 0 or with qualifier 0, 1, 2, or 6
Object
Point
Var
Description
Format
Range
Multiplier
20
0
5
W-hours,
Positive
UINT32
0 to
99999999
20
1
5
W-hours,
Negative
UINT32
0 to
99999999
Whr
20
2
5
VAR-hours,
Positive
UINT32
0 to
99999999
VARhr
20
3
5
VAR-hours,
Negative
UINT32
0 to
99999999
VARhr
20
4
5
VA-hours, Total
UINT32
0 to
99999999
VAhr
Multiplier = 10(nd), where n and d
are derived from
the energy
format. n = 0, 3,
or 6 per energy
format scale and
d=
number of
decimal places.
Units
Whr
Comments
example: energy
format = 7.2K and
W-hours counter =
1234567 n=3 (K
scale), d=2 ( 2 digits
after decimal point),
multiplier = 10(3-2)
= 101 = 10, so
energy is 1234567 *
10 Whrs, or
12345.67 KWhrs
Table C–5: Object 30 - Analog Inputs (Secondary Readings) - Read via Class 0 or with qualifier 0, 1, 2, or 6
Object
Point
Var
Description
30
0
4
Meter Health
sint16
0 or 1
N/A
None
0 = OK
30
1
4
Volts A-N
sint16
0 to 32767
(150 / 32768)
V
Values above
150V
secondary read
32767.
30
2
4
Volts B-N
sint16
0 to 32767
(150 / 32768)
V
30
3
4
Volts C-N
sint16
0 to 32767
(150 / 32768)
V
30
4
4
Volts A-B
sint16
0 to 32767
(300 / 32768)
V
30
5
4
Volts B-C
sint16
0 to 32767
(300 / 32768)
V
30
6
4
Volts C-A
sint16
0 to 32767
(300 / 32768)
V
30
7
4
Amps A
sint16
0 to 32767
(10 / 32768)
A
30
8
4
Amps B
sint16
0 to 32767
(10 / 32768)
A
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Format
Range
Multiplier
Units
Comments
Values above
300V
secondary read
32767.
Values above
10A
secondary read
32767.
C–7
APPENDIX C: DNP MAPPING
Table C–5: Object 30 - Analog Inputs (Secondary Readings) - Read via Class 0 or with qualifier 0, 1, 2, or 6
C–8
Object
Point
Var
Description
Format
Range
Multiplier
Units
30
9
4
Amps C
sint16
0 to 32767
(10 / 32768)
A
30
10
4
Watts, 3-Ph total
sint16
-32768 to
+32767
(4500 / 32768)
W
30
11
4
VARs, 3-Ph total
sint16
-32768 to
+32767
(4500 / 32768)
VAR
30
12
4
VAs, 3-Ph total
sint16
0 to +32767
(4500 / 32768)
VA
30
13
4
Power Factor, 3Ph total
sint16
-1000 to +1000
0.001
None
30
14
4
Frequency
sint16
0 to 9999
0.01
Hz
30
15
4
Positive Watts, 3Ph,
Maximum Avg
Demand
sint16
-32768 to
+32767
(4500 / 32768)
W
30
16
4
Positive VARs, 3Ph,
Maximum Avg
Demand
sint16
-32768 to
+32767
(4500 / 32768)
VAR
30
17
4
Negative Watts,
3-Ph, Maximum
Avg Demand
sint16
-32768 to
+32767
(4500 / 32768)
W
30
18
4
Negative VARs, 3Ph, Maximum Avg
Demand
sint16
-32768 to
+32767
(4500 / 32768)
VAR
30
19
4
VAs, 3-Ph,
Maximum Avg
Demand
sint16
-32768 to
+32767
(4500 / 32768)
VA
30
20
4
Angle, Phase A
Current
sint16
-1800 to +1800
0.1
degree
30
21
4
Angle, Phase B
Current
sint16
-1800 to +1800
0.1
degree
30
22
4
Angle, Phase C
Current
sint16
-1800 to +1800
0.1
degree
30
23
4
Angle, Volts
A-B
sint16
-1800 to +1800
0.1
degree
30
24
4
Angle, Volts
B-C
sint16
-1800 to +1800
0.1
degree
30
25
4
Angle, Volts
C-A
sint16
-1800 to +1800
0.1
degree
Comments
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX C: DNP MAPPING
Table C–5: Object 30 - Analog Inputs (Secondary Readings) - Read via Class 0 or with qualifier 0, 1, 2, or 6
Object
Point
Var
Description
Format
Range
Multiplier
Units
30
26
4
CT numerator
sint16
1 to 9999
N/A
none
30
27
4
CT multiplier
sint16
1, 10, or 100
N/A
none
30
28
4
CT
denominator
sint16
1 or 5
N/A
none
30
29
4
PT numerator
SINT16
1 to 9999
N/A
none
30
30
4
PT multiplier
SINT16
1, 10, or 100
N/A
none
30
31
4
PT
denominator
SINT16
1 to 9999
N/A
none
30
32
4
Neutral
Current
SINT16
0 to 32767
(10 / 32768)
A
Comments
CT ratio =
(numerator *
multiplier) /
denominator
PT ratio =
(numerator *
multiplier) /
denominator
For 1A model,
multiplier is (2 /
32768) and
values above
2A
secondary read
32767
Table C–6: Object 80 - Internal Indicator
Object
Point
Var
80
7
1
Description
Device Restart Bit
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Format
Range
Multiplier
Units
N/A
N/A
N/A
none
Comments
Clear via
Function 2
(Write),
Qualifier Code
0.
C–9
APPENDIX C: DNP MAPPING
C.7
DNP Message Layouts
Legend
All numbers are in hexadecimal base. In addition the following symbols are used.
dst
16 bit frame destination address
src
16 bit frame source address
crc
DNP Cyclic redundant checksum (polynomial
x16+x13+x12+x11+x10+x7+x6+x5+x2+1)
x
transport layer data sequence number
y
application layer data sequence number
Link Layer related frames
Reset Link
Request
05
64
05
C0
dst
src
crc
Reply
05
64
05
00
src
dst
crc
Request
05
64
05
C1
dst
src
crc
Reply
05
64
05
00
src
dst
crc
Request
05
64
05
C9
dst
src
crc
Reply
05
64
05
0B
src
dst
crc
Reset User
Link Status
Application Layer related frames
Clear Restart
C–10
Request
05
Cx
64
Cy
0E
02
C4
50
dst
01
00
Reply
05
Cx
64
Cy
0A
81
44 src
int. ind.
crc
src
07
dst
07
crc
00
crc
crc
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX C: DNP MAPPING
Class 0 Data
Request
05
Cx
64
Cy
0B
01
C4
3C
dst
01
06
src
crc
Request
(alternate)
05
Cx
64
Cy
14
01
C4
3C
dst
02
06
src
3C
Reply
05
Cx
(same for
pt 1
either request) 00
pt6
64
Cy
72 44 src
81 int. ind.
pt 2
00 20 pt 0
pt 7
pt 8
pt 15
pt 16
pt 23
pt 24
pt 31
pt 32
crc
03
crc
06
dst
crc
05 00 00
pt 3
pt 1
pt 2
pt 9
pt 10
pt 17
pt 18
pt 25
pt 26
0A 02 00 00
14
3C
04
04
pt 0
pt 4
06
3C
01
06
crc
pt 3
pt 11
pt 19
pt 27
02 pt0
pt 4
pt 12
pt 20
pt 28
pt1 pt2
pt 1
1E 04
pt 5
pt6
pt 13
pt 21
pt 29
crc
crc
crc
crc
crc
crc
crc
Reset Energy
Request
05
Cx
00
64
Cy
00
18
05
00
C4
0C
crc
dst
01
17
Reply
05
Cx
01
64
Cy
00
1A
81
00
44 src
int. ind.
00 00
0C
crc
Request
(alternate)
05
Cx
01
64
Cy
00
1A
05
00
C4
0C
00
dst
01
00
28
crc
Reply
05
Cx
00
64
Cy
00
1C
81
01
44 src
int. ind.
00 00
0C
00
src
01
00
crc
03
00
00
00
00
00
01
00
crc
dst
01
17
crc
01
00
03
00
00
00
00
00
crc
src
01
00
crc
00
00
03
00
00
00
00
00
crc
dst
01
00
28
crc
crc
01
00
00
00
03
00
00
00
crc
crc
03
00
00
00
00
00
01
00
crc
Switch to Modbus
Request
05
Cx
00
64
Cy
00
18
06
00
C4
0C
crc
dst
01
17
src
01
01
No Reply
Reset Demand (Maximums & Minimums)
Request
05
Cx
00
64
Cy
00
18
05
00
C4
0C
crc
dst
01
17
Reply
05
Cx
01
64
Cy
00
1A
81
00
44 src
int. ind.
00 00
0C
crc
Request
(alternate)
05
Cx
01
64
Cy
00
1A
05
00
C4
0C
00
dst
01
00
28
crc
Reply
05
Cx
00
64
Cy
00
1C
81
01
44 src
int. ind.
00 00
0C
00
src
01
02
crc
03
00
00
00
00
00
01
00
crc
dst
01
17
crc
01
02
03
00
00
00
00
00
crc
src
01
02
crc
00
00
03
00
00
00
00
00
crc
dst
01
00
28
crc
crc
01
02
00
00
03
00
00
00
crc
Error Reply
Reply
05
Cx
64
Cy
0A
81
44 src
int. ind.
crc
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
dst
crc
C–11
APPENDIX C: DNP MAPPING
C.8
Internal Indication Bits
Bits implemented in the EPM7000 meter are listed below. All others are always
reported as zeroes.
Bad Function
Occurs if the function code in a User Data request is not Read (0x01), Write (0x02),
Direct Operate (0x05), or Direct Operate, No Ack (0x06).
Object Unknown
Occurs if an unsupported object is specified for the Read function. Only objects 10, 20,
30, and 60 are supported.
Out of Range
Occurs for most other errors in a request, such as requesting points that don’t exist or
direct operate requests in unsupported formats.
Buffer Overflow
Occurs if a read request or a read response is too large for its respective buffer. In
general, if the request overflows, there will be no data in the response while if the
response overflows at least the first object will be returned. The largest acceptable
request has a length field of 26, i.e. link header plus 21 bytes more, not counting
checksums. The largest possible response has 7 blocks plus the link header.
Restart All Stations
These 2 bits are reported in accordance with standard practice.
C–12
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Digital Energy
Multilin™ EPM 7000
Power Quality Meter
Appendix D: Using the USB to IrDA
Adapter (CAB6490)
Using the USB to IrDA Adapter (CAB6490)
D.1
Introduction
COM 1 of the EPM7000 meter is the IrDA port, located on the face of the meter. One way to
communicate with the IrDA port is with a USB to IrDA Adapter (CAB6490), which allows you
to access the EPM7000 meter's data from a PC. This Appendix contains instructions for
installing the USB to IrDA Adapter.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
D–1
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
D.2
Installation Procedures
The USB to IrDA Adapter comes packaged with a USB cable and an Installation CD. Follow
this procedure to install the Adapter on your PC.
D–2
1.
Connect the USB cable to the USB to IrDA Adapter, and plug the USB into your
PC's USB port.
2.
Insert the Installation CD into your PC's CD ROM drive.
3.
You will see the screen shown below. The Found New Hardware Wizard allows
you to install the software for the Adapter. Click the Radio Button next to
Install from a list or specific location.
4.
Click Next. You will see the screen shown on the next page.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
5.
Make sure the first Radio Button and the first Checkbox are selected, as
shown in the above screen. These selections allow the Adapter's driver to be
copied from the Installation disk to your PC.
6.
Click Next. You will see the screen shown below.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
D–3
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
D–4
7.
When the driver for the Adapter is found, you will see the screen shown below.
8.
You do not need to be concerned about the message on the bottom of the
screen. Click Next to continue with the installation.
9.
You will see the two windows shown below. Click Continue Anyway.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
10. You will see the screen shown on the next page while the Adapter's driver is
being installed on your PC.
11. When the driver installation is complete, you will see the screen shown below.
12. Click Finish to close the Found New Hardware Wizard.
IMPORTANT! Do NOT remove the Installation CD until the entire procedure has completed.
13. Position the USB to IrDA Adapter so that it points directly at the IrDA on the
front of the EPM7000 meter. It should be as close as possible to the meter, and
not more than 15 inches/38 cm away from it.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
D–5
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
14. The Found New Hardware Wizard screen opens again.
This time, click the Radio Button next to Install the software automatically.
15. Click Next. You will see the screen shown below.
D–6
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
16. Make sure the first Radio Button and the first Checkbox are selected, as
shown in the above screen. Click Next. You will see the two screens shown
below.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
D–7
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
17. When the installation is complete, you will see the screen shown below.
Click Finish to close the Found New Hardware Wizard.
18. To verify that your Adapter has been installed properly, click:
Start>Settings>Control Panel>System>Hardware>Device Manager.
The USB to IrDA Adapter should appear under both Infrared Devices and
Modems (click on the + sign to display all configured modems). See the
example screen below.
Note
If the Adapter doesn't show up under Modems, move it away from the meter for a minute
and then position it pointing at the IrDA, again.
19. Double-click on the Standard Modem over IR link (this is the USB to IrDA
Adapter). You will see the Properties screen for the Adapter.
D–8
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
20. Click the Modem tab. The COM Port that the Adapter is using is displayed in
the screen.
21. Use this COM Port to connect to the meter from your PC, using the GE
Communicator EXT software. Refer to Chapter 5 of the GE Communicator EXT
3.0 User Manual for detailed connection instructions.
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
D–9
APPENDIX D: USING THE USB TO IRDA ADAPTER (CAB6490)
D–10
MULTILIN EPM7000 - POWER QUALITY METER – USER GUIDE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement