Installation Instructions

Instrucciones de Instalacion

Instructions d'installation

COLONY SOFT

DECK MOUNT TRIM KIT

JUEGO DECORATIVO PARA CUBIERTA COLONY

T975.400/400BP

TROUSSE DE GARNITURE POUR MONTAGE SUR

T975.500/500BP

PLAGE D’ÉVIER COLONY

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Gracias por preferir American Standard…. El punto de referencia de la más fina calidad por más de

100 años. Para asegurar que su instalación se efectue de la mejor forma favor de leer estas instrucciones cuidadosamente antes de empezar.

Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure depuis plus de 100 ans. Pour s'assurer d'une installation sans inconvénients, veuillez lire attentivement ces instructions avant de commencer.

H

C

Certified to comply with ANSI A112.18.1

U.S. Patent No. D403,750

M 9 6 8 7 5 7 D

3 1

SPOUT INSTALLATION

CAUTION

Turn off hot and cold water supplies before beginning.

4

1

5

Complete FINISHED DECK (A) before trim installation.

Turn off the water supplies.

Remove the GUARDS (1) from the VALVE BODIES (2). Remove the A

SPOUT GUARD (3) and 1/4" PLUG (4) from the SPOUT SHANK (5).

The SPOUT SHANK (6) height should be 1" to 2" above the FINISHED

DECK (A). Cut the SPOUT SHANK (5) if necessary. Remove all burrs and bevel the end of the shank. Failure to do so may damage the SPOUT O-ring during installation and cause water leakage.

Drill a 3/16" HOLE (C) in the finished deck. See TEMPLATE for location.

Lubricate the SPOUT O-RING (6).

Remove the PLUG BUTTON (7) from the SPOUT (8).

Position the RUBBER RING (9) in the GROOVE (B) in the base of the SPOUT (8).

Push the SPOUT (8) down onto the SPOUT SHANK (5) and align the SPOUT PIN (12) with the 3/16" DRILLED HOLE (C) in the FINISHED DECK (A).

Tighten the SET SCREW (10) securely with the 5mm HEX KEY (11).

Insert the PLUG BUTTON (7) into the SPOUT (8).

2

REMOVE ALL

BURRS AND

BEVEL

1"- 2"

ARMADO

DE LA LLAVE

ADVERTENCIA: Cierre la tuberia de la ali mentación del agua caliente y fría antes de comenzar lainstalación

Complete la CUBIERTA TERMINADA (A) antes de instalar el juego decorativo.

Cierre el suministro de agua.

Quite los PROTECTORES (1) del CUERPO DE LAS VÁLVULAS (2). Quite el PROTECTOR

DEL GRIFO (3) y el TAPÓN (4) de 1/4 de pulgada (6,4 mm) del POSTE DEL GRIFO (5).

La altura del POSTE DEL GRIFO (5) debe ser de 1 a 2 pulgadas (25 a 51 mm) sobre la CUBIERTA TERMINADA (A). Corte el POSTE DEL GRIFO (5) si es necesario. Quite todas las rebabas y bisele el extremo del poste. Si no lo hace, puede dañar la junta tórica del GRIFO durante la instalación y ocasionar fugas.

Taladre un AGUJERO (C) de 3/16 de pulgada (4,8 mm) en la cubierta terminada.

Consulte la PLANTILLA para conocer la ubicación.

FRONT

Lubrique las JUNTAS TÓRICAS DEL GRIFO (6).

Quite el BOTÓN OBTURADOR (7) del GRIFO (8).

Coloque el ANILLO DE CAUCHO (9) en la RANURA (B) de la base del GRIFO (8).

Empuje el GRIFO (8) hacia abajo sobre el POSTE DEL GRIFO (5) y alinee el PASADOR DEL

GRIFO (12) con el AGUJERO PERFORADO (C) de 3/16 de pulgada (4,8 mm) en la CUBIERTA TERMINADA (A).

Apriete firmemente el TORNILLO DE SUJECIÓN (10) utilizando la LLAVE HEXAGONAL (11) de 5 mm.

Inserte el BOTÓN OBTURADOR (7) en el GRIFO (8).

5

20.5mm

(13/16")

3/16" DIA.

HOLE

TEMPLATE FOR

SPOUT ROLL

PIN LOCATION

PLANTILLA DE UBICACIÓN DEL

PASADOR DE GIRO DEL GRIFO

GUIDE POUR L’EMPLACEMENT DE LA

GOUPILLE CYLINDRIQUE DU BEC.

C

INSTALLER

LE ROBINET

ATTENTION d'eau chaude et froideavant de commencer.

8

Terminer la PLAGE DE L’ÉVIER FINIE (A) avant d’installer les garnitures.

Couper l’alimentation d’eau.

Retirer les PROTECTEURS (1) des CORPS DE VANNE (2). Retirer le PROTECTEUR DU BEC (3) et le TAMPON (4) de 6 mm de la TIGE

DU BEC (5).

La TIGE DU BEC (6) devrait dépasser la PLAGE DE L’ÉVIER

FINIE (A) d’une hauteur de 2,5 à 5,0 cm. Couper la TIGE DU

BEC (5) si nécessaire. Retirer toutes les barbures et niveler

A

10

12 l’extrémité de la tige. Sinon, le joint torique du BEC risque d’être endommagé durant l’installation et causer des fuites d’eau.

Percer un TROU (C) de 5 mm dans la plage de l’évier finie. Se reporter au GUIDE pour connaître l’emplacement.

5

Lubrifier le JOINT TORIQUE DU BEC (6) et

Retirer la CAPSULE DU TAMPON (7) du BEC (8).

C

Placer la BAGUE DE CAOUTCHOUC (9) dans la RAINURE (8) située dans la base du BEC (8).

Pousser le BEC (8) vers le bas dans la TIGE DU BEC (5) et aligner la GOUPILLE DU BEC (12) avec le

TROU PERCÉ (C) de 5 mm situé dans la PLAGE DE L’ÉVIER FINIE (A).

Serrer la VIS DE RÉGLAGE (10) fermement au moyen d’une CLÉ HEXAGONALE (11) de 5 mm.

Insérer la CAPSULE DU TAMPON (7) dans le BEC (8).

11

7

B

9

12

6

2

VALVE TRIM

Fit ESCUTCHEON SEALS (1) into underside of VALVE ESCUTCHEONS (2).

Thread the VALVE ESCUTCHEONS (2) into the VALVE BODIES (3). Align the HANDLE

STEM (4) with the SLEEVE (5) as necessary. Thread the VALVE ESCUTCHEON (2) into the BODIES (3) until the ESCUTCHEON (2) contacts the finished deck.

1

4 2

3

JUEGO DE ESCUDETE

Coloque los SELLOS DE LOS CHAPETONES (1) en la parte inferior de los CHAPETONES

DE LAS VÁLVULAS (2).

Enrosque los CHAPETONES DE LAS VÁLVULAS (2) en los CUERPOS DE LAS VÁLVULAS (3).

Alinee el TALLO DE LA LLAVE (4) con el MANGUITO (5) si es necesario. Enrosque el

CHAPETÓN DE LA VÁLVULA (2) en el CUERPO (3) hasta que el CHAPETÓN (2) haga contacto con la cubierta terminada.

5

KIT D'ÉCUSSON

Insérer les JOINTS DE ROSACE (1) dans la face inférieure des JOINTS DE VANNE (2).

Enfiler les JOINTS DE VANNE (2) dans les CORPS DE VANNE (3). Aligner la TIGE DE LA POIGNÉE (4) avec le MANCHON (5), au besoin. Enfiler le JOINT DE VANNE (2) dans les CORPS (3) jusqu’à ce que le JOINT (2) entre en contact avec la plage de l’évier finie.

3

INSTALL LEVER HANDLE TRIM

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).

Install the ADAPTER SCREW (3) and tighten securely.

Position LEVER HANDLE (4) and place on ADAPTER (2). Install the

HANDLE SCREW (5) and tighten securely.

INSTALACIÓN DE LA MANIJA

Gire el TALLO DE LA LLAVE (1) a la posición de cierre.

Coloque el ADAPTADOR DE LA LLAVE (2) en el TALLO DE LA LLAVE (1). Instale el TORNILLO

DEL ADAPTADOR (3) y apriételo firmemente.

Ajuste la posición de la LLAVE DE PALANCA (4) y colóquela sobre el ADAPTADOR (2).

Coloque el TORNILLO DE LA LLAVE (5) y apriételo firmemente.

INSTALLATION DE LA POIGNÉE

Placer la TIGE DE LA POIGNÉE (1) en position « FERMÉE ».

Placer l’ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1). Installer la VIS

D’ADAPTATION (3) et serrer fermement.

Mettre la MANETTE À VOLANT (4) en position et la placer sur l’ADAPTATEUR (2).

Installer la VIS POUR MANETTE (5) et serrer fermement.

4

INSTALL ACRYLIC HANDLE TRIM

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).

Position ACRYLIC HANDLE (3) and install on ADAPTER (2).

Install the HANDLE SCREW (4) and tighten securely.

Push in INDEX BUTTON (5). (Hot-left side , Cold-Right side)

INSTALE LAS MANIJAS ACRÍLICAS

Gire el TALLO DE LA LLAVE (1) a la posición de cierre

Coloque el ADAPTADOR DE PIE DE LA MANIJA (2) en el PIE DE LA MANIJA (1).

Ubique la MANIJA ACRÍLICA (3) en el ADAPTADOR DE PIE DE LA MANIJA (2).

Instale el TORNILLO DE MANIJA (4) y ajuste bien.

Presione sobre BOTÓN ÍNDICE (5).

INSTALLER LES POIGNÉES EN ACRYLIQUE

Placer la TIGE DE LA POIGNÉE (1) en position « FERMÉE ».

Placer l’ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1).

Placer la POIGNÉE EN ACRYLIQUE (3) sur la l’ADAPTATEUR DE POIGNÉE (2).

Installer les VIS POUR LES POIGNÉES (4) et bien serrer.

Insérer le BOUTON INDICATEUR (5).

5

4

3

1

2

4

5

3

2

1

H

M 9 6 8 7 5 7 D

5

TEST INSTALLED FAUCET

Remove STREAM STRAIGHTENER (1). With handles in OFF position, turn on water supplies and check all connections for leaks.

Operate both handles to flush water lines thoroughly.

Replace STREAM STRAIGHTENER (1).

PRUEBA DE LA LLAVE INSTALADA

Quite el REGULADOR DEL CHORRO DE AGUA (1). Cierre las llaves, abra el suministro de agua y revise las conexiones para asegurar que no tengan fugas.

Girar ambos manerales para dejar fluir el agua de las tuberias.

Accionar la varilla del drenaje y cheque contra fugas. Reinstalar el

REGULADOR DEL CHORRO DE AGUA (1).

2

TESTER L'INSTALLATION DU ROBINET

Retirer le DISPOSITIF DE REDRESSEMENT DU JET (1). Tout en gardant les poignées en position FERMÉE, mettre l’alimentation d’eau en marche et vérifier tous les raccords pour s’assurer qu’il n’y ait pas de fuites.

Ouvrir les deux POIGNÉES, rincer les conduits d'eau abondamment.

Opérer la TIGE DE LEVAGE et vérifier si le VIDAGE fuit. Replacer le DISPOSITIF

DE REDRESSEMENT DU JET (1).

1

6

If faucet drips proceed as follows:

Si la llave gotea proceda como sigue:

Stream straightener may accumulate dirt causing distorted and reduced water flow. Remove aerator and rinse clean.

If spout drips, operate handles several times from OFF to ON position.

Do not force-handles turn only 90˚.

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH

CLEAR WATER. DRY WITH A SOFT COTTON

FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH

SOAPS, ACID, POLISH, ABRASIVES, HARSH

CLEANERS, OR A CLOTH WITH A COARSE

SURFACE.

El aireador tal vez acumule suciedad, causando un flujo no uniforme del agua

Remover el aireador, enjuagar y limpiar.

Si la salida gotea gire los manerales varias veces desde la posición de cerrado a la posición de abierto. No force los manerales, solamente girelos a 90 grados.

INSTRUCCIONES DE CUIDADO

DEL PRODUCTO:

LIMPIE EL PRODUCTO CON AGUA LIMPIA

Y SÉQUELO CON UNA TELA SUAVE DE

FRANELA DE ALGODÓN.

NO LIMPIE EL PRODUCTO CON JABÓN,

ÁCIDOS, PULIDORES, ABRASIVOS,

LIMPIADORES FUERTES O TELAS ÁSPERAS.

Si le robinet coule, suivre les instructions suivantes:

La saleté peut s'accumuler dans l'aérateur et causer un débit d'eau plus faible ou inégal.

Enlever l'aérateur et rincer.

Si le bec coule, ouvrir et fermer les poignées plusieurs fois de suite. Ne pas forcer. Tourner seulement à 90˚.

INSTRUCTIONS POUR L'ENTRETIEN

FAIRE : SIMPLEMENT RINCER LE PRODUIT AVEC DE

L'EAU CLAIRE JUSQU'À CE QU'IL SOIT PROPRE SÉCHER

AVEC UN LINGE DE FLANELLE DE COTON DOUX.

NE PAS FAIRE : NE PAS NETTOYER LE PRODUIT AVEC

DES SAVONS, DE L'ACIDE, DU POLISH, DES ABRASIFS,

DES NETTOYANTS AGRESSIFS OU UN LINGE À TEXTURE

RUGUEUSE.

HOTLINE FOR HELP NUMBERO DE EMERGENCIA ASSISTANCE TÉLÉPHONIQUE

For toll-free information and answers to your questions, call:

Para información y respuestas a sus preguntas, llame sin costo al:

Pour information et réponses à vos questions, composer sans frais:

1 800 442-1902

Weekdays Días laborales de las Sur semaine:

8:00 to 8:00 p.m. EST

CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays Días laborales de las Sur semaine:

8:00 to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

© A m e r i c a n S t a n d a r d I n c . 2 0 0 1

M 9 6 8 7 5 7 D

M918504-0070A

SCREW

Tornillo

VIS

M908423-0070A

ACRYLIC HANDLE

Maneral Acrilico

POIGNÉE ACRYLIQUE

H

COLONY SOFT DECK MOUNT TRIM KIT

JUEGO DECORATIVO PARA CUBIERTA COLONY

TROUSSE DE GARNITURE POUR MONTAGE SUR

PLAGE D’ÉVIER COLONY

MODEL NUMBER

NÚMERO DE MODELO

NUMÉRO DE MODÈLE

M950144-0070A

INDEX, BUTTON, HOT

Boton Indicador de

Agua Caliente

BOUTON INDEX, CHAUD

T975.400BP

T975.400

T975.500BP

T975.500

M950143-0070A

INDEX, BUTTON, COLD

Boton Indicador de

Agua Fria

BOUTON INDEX, FROID

M916803-YYY0A

METAL LEVER HANDLE

MANIJA METÁLICA

POIGNÉE MÉTALLIQUE PLEINE

M961461-YYY0A

BUTTON AND SCREW

BOTON Y TORNILLO

BOUTON ET VIS

M918075-0070A

HANDLE SCREW

TORNILLO DE LA MANIJA

VIS DE LA POIGNÉE

M918504-0070A

SCREW

TORNILLO

VIS

M918021-0070A

ADAPTER

ADAPTAR

APPROPRIER

M961460-0020A

VALVE ESCUTCHEON KIT

JUEGO DE ESCUDETE

KIT D'ÉCUSSON

M961640-YYY0A

SPOUT

BOQUILLA

BEC

028678-0070A

STREAM STRAIGHTENER

REGULADOR DE CHORRO DE AGUA

REDRESSEUR DE JET

Replace the "YYY" with appropriate finish code

Reemplace las letras "YYY" por el código de acabado

Remplacer le "YYY" par le code de finition approprié

CHROME, CROMO, CHROME

POLISHED BRASS, BRONCE PULIDO, LAITON POLI

002

099

M 9 6 8 7 5 7 D

DECK MOUNT

TUB FILLERS

Installation

Instructions

T990.5XX

COLONY DIVERTER & PERSONAL

SHOWER TRIM KIT

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1

U.S. Patent No. D403,750

M 9 6 8 7 6 2

M918075-0070A

HANDLE SCREW

M918504-0070A

ADAPTER SCREW

M918021-0070A

ADAPTER

M916803-0070A

METAL LEVER

HANDLE

M961463-0020A

HAND SHOWER

033760-0070A

HAND SHOWER

SEAL KIT

M961460-0020A

VALVE

ESCUTCHEON

M961464-0020A

HAND SHOWER

HOLDER

028667-0020A

HAND SHOWER

HOSE AND SEALS

(AVAILABLE WITH R890)

1

INSTALL DIVERTER VALVE TRIM

DIVERTER

GUARD

REMOVE THE DIVERTER GUARD.

Place the ESCUTCHEON SEAL over the DIVERTER BODY.

Thread the VALVE ESCUTCHEON into the DIVERTER BODY.

Align the HANDLE STEM with the SLEEVE as necessary.

Thread the VALVE ESCUTCHEON into the BODY until the

ESCUTCHEON contacts the finished deck.

HANDLE

STEM

ESCUTCHEON

SEAL

SLEEVE

VALVE

ESCUTCHEON

FINISHED

DECK

2

INSTALL HANDLE TRIM

Turn HANDLE STEM fully clockwise (Tub Filler position).

Place the HANDLE ADAPTER on the HANDLE STEM.

Install the ADAPTER SCREW and tighten securely.

Position LEVER HANDLE and place on ADAPTER. Install the HANDLE SCREW and tighten securely.

HANDLE

SCREW

ADAPTER

SCREW

ADAPTER

HANDLE

STEM

METAL

LEVER

HANDLE

3

INSTALL HAND SHOWER

Unscrew the HOLDER from the SHOWER ESCUTCHEON. Slip the

SHOWER HOSE through the HOLDER and the SHOWER ESCUTCHEON.

Insert a SEAL WASHER into the SHOWER HOSE CONNECTOR.

Pull out the SLEEVE GUARD and HOSE. Unthread the SLEEVE GUARD from the HOSE END connection. Be careful not to allow the HOSE to fall back through the SLEEVE.

Thread the SHOWER HOSE onto the HOSE END connection and tighten securely.

HAND SHOWER

SEAL WASHER

HOLDER

SHOWER HOSE

SHOWER ESCUTCHEON

RUBBER RING

SLEEVE

GUARD

SHOWER HOSE

SEAL WASHER

HOSE END

HOSE

SLEEVE

HAND SHOWER

Apply a sealant around the HOSE HOLE.

Thread the SHOWER ESCUTCHEON into the SLEEVE until the ESCUTCHEON contacts the finished deck.

Loosen the SET SCREW in the SHOWER ESCUTCHEON and rotate the

ESCUTCHEON towards the center of the tub. Retighten the SET SCREW.

Thread the HOLDER into the SHOWER ESCUTCHEON.

Insert a SEAL WASHER into the SHOWER HOSE connector and connect the HAND SHOWER.

Place the HAND SHOWER into the HOLDER.

SLEEVE

SEAL WASHER

HOLDER

SET SCREW

SHOWER

ESCUTCHEON

SEALANT

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A m e r i c a n S t a n d a r d I n c . 2 0 0 1

M 9 6 8 7 6 2

DECK MOUNT

TUB SYSTEMS

ROUGH VALVE KIT

Installation

Instructions

R800 SERIES

R810 SERIES

Thank you for selecting American-Standard...

the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

R810 SERIES

R800 SERIES

Certified to comply with ANSI A112.18.1

U.S. Patent No. D403,750

M 9 6 8 6 5 0 C

1

ROUGHING-IN

1

3

(2) 1-3/8 D

HOLES

FITTING

MOUNTING

SURFACE

2 FINISHED

DECK

1-3/8 D

MAX.

1" D

1/2" COPPER

INLET SUPPLIES

8" to 12"

10" for R810

1 D MAX.

ACRYLIC

BATH

MOUNTING

4

7-1/8

1. DECK THICKNESS

TOTAL DECK THICKNESS UP TO 2-1/2"

2. FINISHED DECK

FINISHED DECK VARIABILITY ACCOMMODATES

DECKING MATERIAL (TILE, MARBLE, CORIAN®...)

TO 1" THICK

3. FITTING MOUNTING SURFACE

ADJUSTABILITY, TO 1-1/2" THICK

4. ACRYLIC BATHS

ADJUSTABILITY, TO 1-1/2" THICK

1" D (2) 1-3/8 D

HOLES

8" to 12"

10" for R810

DECK MOUNTING HOLES

2

MOUNT SPOUT SHANK

Drill holes in mounting deck as shown. The maximum allowable deck thickness is 1-1/2".

Insert the SPOUT SHANK through the mounting deck from below. Assemble the SPOUT SHANK LOCK RING so it is flush with the top of the threads on the SHANK.

SPOUT SHANK

LOCK RING

SPOUT SHANK LOCK RING FLUSH WITH

TOP OF THREADS ON SPOUT SHANK

SPOUT SHANK

FRICTION WASHER

MOUNTING NUT

SPOUT SHANK

FITTING

MOUNTING

DECK

1-1/2 MAX.

3

MOUNT VALVE BODIES

Cut the copper outlet tubes of the VALVE BODIES as required.

(Not necessary for R810).

Insert the HOT and COLD VALVE BODIES into the TEE. (Not necessary for R810). The HOT VALVE BODY is marked with a red label.

Insert the VALVE BODIES and TEE through the mounting deck from below. Assemble the VALVE LOCK RINGS so they are flush with the top of the VALVE BODIES.

Insert the SPOUT SHANK into the TEE.

(Not necessary for R810).

Tighten the VALVE BODY and SHANK MOUNTING

NUTS securely.

Fasten the VALVE LOCK RING to the wooden mounting surface with #8 screws (not provided).

VALVE

BODY

FITTING

MOUNTING

DECK

VALVE

LOCK RING

FRICTION WASHER

MOUNTING NUT

VALVE LOCK RING FLUSH WITH

TOP OF THREADS ON VALVE SHANK

VALVE

LOCK RING

# 8 SCREWS

SPOUT

SHANK

COLD

HOT

TEE

OUTLET TUBE

(CUT AS REQUIRED)

4

SOLDER CONNECTIONS

Connect the water supply lines to the copper inlet tubes of the VALVE BODY.

Solder all TEE and WATER SUPPLY CONNECTIONS.

Remove the GUARD from the SPOUT SHANK. Assemble the 1/4" PLUG to the SPOUT SHANK with a thread sealant.

Turn on the water supplies and check all connections for leakage.

Replace the GUARD on the SPOUT SHANK. Turn off the water supplies.

SPOUT GUARD

1/4" PLUG

TEE

CONNECTIONS

WATER SUPPLY

CONNECTIONS

5 SERVICE

TO CHANGE THE DIRECTION OF HANDLE ROTATION

Turn off the water supplies.

Turn HANDLE to the off position.

Unscrew the VALVE LOCK NUT and remove.

A 17mm deep socket is required.

Remove the CARTRIDGE by pulling upon the SLEEVE.

Remove the SLEEVE from the CARTRIDGE.

Remove the SPRING CLIP.

Remove the STOP WASHER. Turn it 90˚ and replace.

STOP

WASHER

Replace the SPRING CLIP.

Reverse the above steps to reassembly the components.

If the spout drips, operate the handles several times from the off to the on position. Do not force - the handles only turn 90˚

DEEP SOCKET

17mm (11/16")

90

VALVE

LOCK NUT

SCREW

SLEEVE

SPRING

CLIP

VALVE

CARTRIDGE

M 9 6 8 6 5 0 C

SPINDLE

903898-0070A

VALVE CARTRIDGE

994053-0070A

VALVE MOUNTING KIT

M962278-0070A

VALVE LOCK RING

M906671-0070A

VALVE LOCK NUT

A911546-0070A

DECK MOUNT TUB SYSTEMS

MODEL NUMBERS

R800

R810

SCREW

918319-0070A

SPOUT LOCK RING

A906110-0070A

SPOUT MOUNTING KIT

M962279-0070A

DEEP SOCKET

17mm (11/16")

M962273-0070A

SOCKET NOT INCLUDED

WITH FITTING

R810 SERIES

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

C A m e r i c a n S t a n d a r d I n c . 2 0 0 3

*WITH BRAZED TEE

M 9 6 8 6 5 0 C

DECK MOUNT

TUB FILLERS

Installation

Instructions

R890 SERIES

DIVERTER & PERSONAL SHOWER

ROUGH VALVE KIT

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1

U.S. Patent No. D403,750

M 9 6 8 3 5 5 D

1

ROUGHING-IN

1-3/8 D

HOLE

1-3/8 D

MAX.

6 to 18

FINISHED

DECK 2

1-3/8 D

MAX.

ACRYLIC

BATH

MOUNTING

4

1

3-5/8

3

1/2" NPT

FITTING

MOUNTING

SURFACE

SHW

4-5/16

5-5/16

1/2" NPT INLET

1-3/8 D

1. DECK THICKNESS

TOTAL DECK THICKNESS UP TO 2-1/2"

2.

FINISHED DECK

FINISHED DECK VARIABILITY ACCOMMODATES

DECKING MATERIAL (TILE, MARBLE, CORIAN®...)

TO 1" THICK

3. FITTING MOUNTING SURFACE

ADJUSTABILITY, TO 1-1/2" THICK

4. ACRYLIC BATHS

ADJUSTABILITY, TO 1-1/2" THICK

1-3/8 D HOLE

FOR DIVERTER

1-3/8 D HOLE

FOR HAND

SHOWER

6 to 18

DECK MOUNTING HOLES

2

LOCATION OF R890 WHEN USED WITH R800

R800 ROUGH VALVE KIT

8" to 12"

HOT AND COLD

VALVE BODIES

A

"A" DIMENSION CAN BE

FLEXIBLE TO

ACCOMMODATE

CUSTOMER'S

REQUIREMENTS

R890 SERIES DIVERTER & PERSONAL

SHOWER ROUGH VALVE KIT

A

BATH SPOUT

CONNECTION

6" to 18"

DIVERTER

VALVE

HAND SHOWER

CONNECTION

HOT

INLET

COLD

INLET

1/2" COPPER WATER

TUBE INLET (MIXED

SUPPLY FROM BATH

FITTING)

PLUMBER TO MAKE ALL PIPING CONNECTIONS

BETWEEN VALVE BODIES, SUPPLY TO TRANSFER

VALVE AND CONNECTION TO BATH SPOUT.

PIPING SHOWN SHADED IS NOT SUPPLIED

AND MUST BE FURNISHED BY INSTALLER.

SHW

1/2" COPPER WATER

TUBE (MIXED SUPPLY

TO TUB FILLER SPOUT)

HOSE OUTLET

(MIXED SUPPLY

TO HAND SHOWER)

3

INSTALLATION NOTE: Use thread sealant on all threaded connections.

Drop the SLEEVE (1) into the hole in the mounting deck.

Assemble the WASHER (2) and LOCKNUT (3) to the SLEEVE (1) and tighten securely.

#8 SCREWS

For copper water tube installations, make two 4" long adapter nipples

( 1/2" Male NPT x 1/2" CWT ). Thread nipples into the inlet and tub outlet of the DIVERTER BODY. Tighten connections securely. Do Not Solder these Connections on the DIVERTER BODY. Damage may occur.

FITTING

MOUNTING

SURFACE

Thread HOSE (4) into the SHOWER CONNECTION (5) of the DIVERTER BODY (6) and tighten securely. Check with local plumbing codes for backflow prevention requirements. Install a backflow prevention device if required.

Assemble MOUNTING NUT (7) and WASHER (8) onto DIVERTER BODY (6).

Insert the DIVERTER BODY (6) through the mounting deck from below.

Assemble the VALVE LOCK RING (9) so it is flush with the top of the DIVERTER BODY (6).

Position the DIVERTER BODY (6) as required and tighten the MOUNTING NUT (7) securely.

VALVE LOCK

RING FLUSH WITH

TOP OF THREADS ON

VALVE SHANK

Fasten the VALVE LOCK RING (9) to the wooden mounting surface with #8 screws (not provided).

Connect the water inlet and tub outlet lines to the DIVERTER BODY (6).

#8 SCREWS

TUB OUTLET

VALVE

BODY

4

TEST Note: Test Cap not provided.

Cap the HOSE OUTLET. Remove the DIVERTER GUARD.

DIVERTER

GUARD

Remove the SPOUT GUARD. Assemble the 1/4" PLUG to the SPOUT

SHANK with a thread sealant. See the R800 SERIES ROUGH VALVE KIT instructions for details.

Turn on the water supplies.

DIVERTER

SLEEVE

Rotate the DIVERTER SLEEVE back and forth fully.

Check all connections for leakage.

1/2" COPPER WATER

TUBE (MIXED SUPPLY

TO TUB FILLER SPOUT) Turn off the water supplies. Replace the DIVERTER

GUARD and the SPOUT GUARD. Remove the CAP from the HOSE OUTLET.

5

HOSE

Insert the HOSE through the SLEEVE from below the mounting deck.

Thread the SLEEVE GUARD onto the HOSE END connection.

Insert the SLEEVE GUARD into the SLEEVE.

HOSE OUTLET

(MIXED SUPPLY

6

SERVICE

TO REMOVE DIVERTER

SCREW

9

5

SLEEVE

GUARD

SLEEVE

1

8

7

6

1-3/8"

Dia. HOLE

FOR HAND

SHOWER

2

3

WATER INLET

4" LONG

ADAPTER

NIPPLES

1/2" COPPER WATER

TUBE INLET (MIXED

SUPPLY FROM BATH

FITTING)

CAP

HOSE

END

HOSE

Turn off the water supplies.

Turn HANDLE to the off position.

Remove the SLEEVE from DIVERTER by losening screw.

Using 14mm (9/16") Deep Socket, remove diverter.

DIVERTER SLEEVE

DEEP SOCKET

14mm (9/16")

DIVERTER

M 9 6 8 3 5 5 D

SCREW

918319-0070A

DIVERTER SLEEVE

903898-0070A

DIVERTER

954559-0070A

DIVERTER & PERSONAL SHOWER

ROUGH VALVE KIT

MODEL NUMBER

R890

VALVE LOCK RING

M906671-0070A

VALVE MOUNTING KIT

M962278-0070A

SLEEVE

922700-0070A

SLEEVE MOUNTING KIT

M962280-0070A

HOSE

M923016-0070

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800 442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-12-00

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A m e r i c a n S t a n d a r d I n c . 2 0 0 4

M 9 6 8 3 5 5 D