www.fsme.com.au Tel: (07) 3277 5388

www.fsme.com.au Tel: (07) 3277 5388
A Division of Premier Engineering (Qld) Pty Ltd ABN 45 056 536 353
FSME I3
Manufacturers and Distributors
We manufacture and market an extensive range of quality products for the Agricultural and
Farming Industries
www.fsme.com.au
Farm Supplies Machinery & Equipment is
Your One-Stop Machinery Shop, where you
can find Farm Equipment, Construction
Equipment and Machinery for all your needs.
Tel: (07) 3277 5388
Fax: (07) 3277 5597
Email: [email protected]
54 Annie Street PO Box 9 Coopers Plains Q 4108
BERENDS • BARE-CO • FARM-AID • MURRAY • R E G A • S I L V A N • S O L O • T E AG L E • V I CO N
WELCOME TO FSME13 PRODUCT GUIDE
You will find extensive changes throughout incorporating the addition of some exiting new
products. This product guide includes but is not limited to, our diverse range of products and
should you have any particular needs, please do not hesitate to call.
FREIGHT
Upon placing purchase orders, please nominate your Freight Company and Account
Code.
If you require post, please advise Postal Address or Reply Paid Address.
FSME does not hold any responsibility for non-delivered orders whereby the customer
requests postage.
NON STOCK ORDERS
Orders for non-stock orders are required to have a 20% non-refundable deposit paid prior
to commencement of manufacture. For further clarification please contact us.
SPARE PARTS
While FSME endeavours to carry stock of most spare parts, an additional freight charge
may be incurred for any non-stock parts ordered.
RETURNS POLICY
Goods returned for credit require authorisation prior to return and will be subject to a
restocking fee.
No claims will be recognised after 14 days.
Any equipment made to special order is non returnable.
If any goods are returned, they must be accompanied by a Request for Credit Form
obtained from FSME and must be authorised by FSME prior to their return.
WARRANTY POLICY
All equipment supplied by FSME is covered by the manufacturer’s standard warranty and
is limited to repairing or replacing the defective part/s at our Coopers Plains facility or as
directed by the manufacturer.
The purchaser is responsible for all freight and incidental costs to and from the factory.
We do not accept any liability on account of the equipment or the repair thereof, and will
not accept liability for special or consequential damage or loss of any kind.
PLEASE ORDER PRODUCTS AS PER CATALOGUE CODE
Every effort has been made to avoid printing errors, however we accept no
responsibility should they occur.
Visit our website: www.fsme.com.au
Page 2
E&OE
INDEX
AERATORS ……………………………………………………………………………….4-5
ANIMAL & WILDLIFE MANAGEMENT ………………………………………....6-7
BARE-CO PRODUCTS …………………………………………………….………..…..8
BALE, HAY & SILAGE EQUIPMENT ………………………………….……..….9-11
CARRYALLS ………………………………………………………………….…...……..12
CEMENT MIXERS ……………………………………………………………………....13
CULTIVATORS - COIL TINE ………………………………………………….…....14
- S-TINE ………………………………………….…...……....15-17
- DISC ………………………………………………...….…....18-24
DAIRY SCRAPERS & SMUDGERS …………………………………………..…....25
DELVER & DRAIN DIGGERS ………………………………………………….......26
DIESEL TANKS & ACCESSORIES ………………………………………….….27-29
DOLOMITE DROPPERS ……………………………………………………………….30
DRUM LIFTERS ………………………………………………………………….……...30
OUR
FENCING & DRILLING …………………………………………………….……..31-36
FERTILISER SPREADERS ………………………………………………...….…37-44
FIRE CONTROL & FIGHTING EQUIPMENT ……………………………....45-48
FLAME GUN ……………………………………………………………………………...49
MOTTO
GRADER BLADES ………………………………………………………………....50-57
GRAIN & WOOL HANDLING EQUIPMENT …………………………........58-59
HARDWARE …………………………………………………………………….......59-60
HARROWS ………………………………………………………………………......61-64
IS
HEADSTOCKS ……………………………………………………………………..…....65
HILLERS, FURROWERS & BED MAKER ASSEMBLIES ……………......65-66
LANDSCAPE RAKES ……………………………………………………………….…...67
LAWN ROLLERS …………………………………………………………………..…....68
QUALITY
LIFTING JIBS & LINKAGE SCOOPS ………………………………………..…....69
LIVESTOCK HANDLING EQUIPMENT ………………………………….…...70-75
LOG SPLITTERS …………………………………………………………………...…...75
MATERIAL HANDLING EQUIPMENT ……………………………………...….….76
AND
MILKING MACHINES ……………………………………………………….…..…….77
MULCHERS ……………………………………………………………….………....78-80
PALLET FORKS ……………………………………………………...………...……….81
PLOUGHS ………………………………………………………………………..…...82-85
SERVICE
PUMPS ……………………………………………………………………………......86-88
RAMPS …………………………………………………………………………….….…….89
REAR END LOADERS ……………………………………………………….……..….89
RIPPERS & PIPELAYING ATTACHMENTS ………………………….….…..90-93
ROTARY HOES …………………………………………………………………...…94-97
SEEDERS ………………………………………………………………………….....…..98
SLASHERS …………………………………………………………………….…….99-115
SPRAY EQUIPMENT ……………………………………………………….…..116-129
STICK RAKES ………………………………………………………………..…….…..130
TOOLBAR TILLER COMPONENTS ………………………………………...…….131
WEEKEND FARMER PACKAGES …………………………………………..……...132
MAJOR BRANDS INFORMATION …………………………………..….....133-135
DELIVERY ANYWHERE IN AUSTRALIA
Page 3
AERATORS
BERENDS GROW-MASTER
The GROW-MASTER Aerator can turn your tired, lifeless soils
into productive, high yielding pastures. The specially designed
tines shatter the compact ground, increasing the absorption of
water and air which in turn encourages root growth.
Each roller can be adjusted to four positions of angle.
Heavy duty 2” triple sealed bearings.
Two bolt gang adjustment to alter rotor angle.
Large floor plate deck for carrying ballast (weight).
Fitted with double rollers angled in opposite directions to reduce sideway drag on
tractor when ground engaging.
Cat 1 & 2 Linkage.
Easily adjusted mounting stands.
Tow hook mounted on the back for dragging pasture harrows.
Tractor horsepower requirement quite low with only 35Hp required on 2.0m unit
Single Rotor Models
0161
0163
0164
0165
0166
1.0m
1.2m
1.4m
1.6m
1.8m
Double Rotor Models
0173
0175
0176
0177
0178
0186
1.6m
2.0m
2.4m
2.8m
3.2m
3.6m
Various trailing models are also available on request.
Water Filled
Aerator
MADE IN AUSTRALIA
Standard Range available as well as
custom made to suit your needs
Visit our website: www.fsme.com.au
Page 4
AERATORS
FARM-AID
The FARM-AID Aerator manufactured in Queensland is used
to aerate the soil to reduce compaction and allows water and
fertilizer to penetrate the soil. Suitable for pastures, ovals,
playing fields etc.
Heavy duty 100 x 50 x 6mm RHS frame.
Self-alining pillow flange bearings.
1 1/4” axles.
14” (355mm) diameter heavy tubular roller which can be filled with water for extra
weight.
5 rows of 150mm slicing tines spaced 12” apart.
FA1000
FA1001
FA1002
FA1003
FA1004
FA1005
FA1006
4’-1200mm
5’-1500mm
6’- 1800mm
7’- 2100mm
8’- 2400mm
9’- 2700mm
10’- 3000mm
Custom made sizes and configurations can be manufactured to suit your
requirements.
FARM-TECH AERVATORS
Used by hundreds of Australian Farmers and now being
exported around the world, the AerVator provides a full
200mm of penetration enhancing air, water & fertilizer
delivery to the root zone.
The unique & patented AerVator tine design loosens the
soil without destroying granular aggregation.
The AerVator is not dragged through the soil therefore,
Horse power requirement and associated fuel costs are low.
SGH SERIES
GH SERIES
AV SERIES
TURF SERIES
1.2M - 2.0M
2.0M - 5.0M
2.0M - 6.0M
1.2M - 2.0M
25 - 50HP
50 - 125HP
60 - 140HP
18 - 45HP
Need a Canopy for your machine?
Contact FSME with your requirements.
DELIVERY ANYWHERE IN AUSTRALIA
Page 5
ANIMAL & WILDLIFE MANAGEMENT
CAGES
The easy and humane means of trapping unwanted animals
and wildlife.
These cages are quality and are made in Queensland.
TWCM
MOUSE
180 x 105 x 70
TWCB
BIRD
450 x 160 x 160
TWCR
RODENT
450 x 160 x 160
TWCRP
RODENT w PLATE
450 x 160 x 160
TWCRA RABBIT
640 x 180 x 180
TWC
CAT
600 x 300 x 300
TWCP
POSSUM
600 x 300 x 300
TWCT
TURKEY
700 x 300 x 400
Please check www.fsme.com.au for our
extensive product range.
D1 1/2
RABBIT & FERRAL CAT
MADE IN AUSTRALIA
600g
D4COIL DINGO & FOX
1.2kg
TRAPS
2.5kg
DINGO & WILD DOG
We’ve got you
caged…...
TRAPS
Manufactured in Australia to RSPCA and Legislation approval “JAW” traps.
Large product range for pest control also available. Please contact
the FSME Sales Team with your requirements.
Visit our website: www.fsme.com.au
Page 6
ANIMAL & WILDLIFE MANAGEMENT
SNAKE GAITERS
OH&S policies, affecting councils, landscape contractors,
and other businesses, require adequate personal
U
protective equipment for employees.
E YO
Protection for outside workers from snakes is an
issue fast becoming a very recognized critical need.
AR
ED?
ECT
T
O
PR
Our Snake Gaiters are specifically designed for protection
from Australian snakes. Alongside the critical need, the
garment has been made tough enough to withstand the
Australian outdoor environment.
ORDER CODE: SPC21
ZON SCARE GUN
Crops and fruit orchards damaged by marauding birds and
animals can be controlled by the strategic placement of the
ZON SCARE GUN.
Automatic piezo-electronic ignition.
Tough construction for all weather operation.
LP Gas Operation (Bottle not included).
10kg Gas bottle has the capacity to fire 17,000 detonations, making the operation cost
just a few cents per day.
Effective operating radius ranges from 1 to 5 acres, depending upon the shape and
topography of the land.
Adjustable detonation intervals from 40 seconds up to 30 minutes.
Volume of the loud shot-like noise can be controlled from 100 to 120 decibels.
Optional Pirouette Stand provides 50 - 70 degrees rotation with explosion.
Optional Clock Timer automatically starts and stops operation of gun each day for
a minimum 10 hours to maximum 18 hours.
08004
ZON SCARE GUN
08014
OPTIONAL PIROUETTE STAND
08030
OPTIONAL CLOCK TIMER
DELIVERY ANYWHERE IN AUSTRALIA
Page 7
BARE-CO PRODUCTS
As a Bare-Co Distributor, we stock an extensive range of tractor products and accessories.
Visit our website: www.fsme.com.au
Page 8
BALE, HAY & SILAGE EQUIPMENT
BERENDS BALE FORKS
0285 - Round Bale Handler
2’ high tensile single spike for piercing round bales.
Small spike stops bales from turning.
Lifting capacity 500kg.
0286 - Bale Fork
Two 2” high tensile spikes for transporting round bales.
Tine spaced at 32” for lifting pallets.
Lifting capacity 1000kg.
Optional 6’ carryall platform can be fitted. (P/N 0132)
Silage Fork
Straight Conus II tines with eccentric nut.
Heat treated to create tensile strength of 1550N/mm².
Category 1 linkage with Cat 2 bushes.
Lifting capacity 1000kg.
Various tine sizes available.
0288 - Big Square Bale Fork
Three 2” high tensile spikes for transporting round bales.
Lifting capacity 1500kg.
Fixed & Adjustable Feed Out Forks
Two models available - Standard Fixed (0284) and Adjustable (0287).
Adjustable model feeds out bales with widths ranging from 4’ to 6’.
Standard Fixed model has tines fixed to accommodate 4’ bales.
Bales can also be carried on the forks for transport.
Rectangular headstock with a centre stay is easy to adapt
to front end loaders with single or dual rams.
Lifting capacity 1000kg.
DELIVERY ANYWHERE IN AUSTRALIA
Page 9
BALE, HAY & SILAGE EQUIPMENT
FARM-AID BALE FORKS
The FARM-AID Bale Forks are Heavy Duty Category 1/2 and are manufactured in
Queensland.
Standard Models
FA1015
TWO SPIKES
FA1016
ONE SPIKE
Custom builds are available upon request.
HAY BALE ELEVATORS
Manufactured in Queensland the HAY BALE ELEVATOR
takes the back breaking work out of stacking and moving hay
bales.
Heavy Duty chain with 1750kg breaking strain.
High tensile sprockets and low friction Teflon bearings.
Maximum 70° operating angle (3.75m vertical lift)
Light weight and fully portable.
Modification cleats optional to allow elevator to take
bagged grain.
Available in both Petrol Driven and 240volt Electric models.
HES001
19’ (5.9m)
3/4HP 240V ELECTRIC
HES002
19’ (5.9m)
1HP 240V ELECTRIC
HES003
19’ (5.9m)
3HP KAWASAKI FJ 100D PETROL
HES004
24’ (7.5m)
3HP KAWASAKI FJ 100D PETROL
HES005
24’ (7.5m)
1HP 240V ELECTRIC
HAY RAKES
The SITREX RP LINKAGE HAYRAKE
is a high quality hay rake manufactured in Italy.
A simple and robust construction ensures minimal maintenance.
Visit our website: www.fsme.com.au
Page 10
BALE, HAY & SILAGE EQUIPMENT
TANCO BALE WRAPPERS
Tanco AutoWrap produces the widest range of quality agricultural wrapping
machinery in the world. Tanco manufactures round bale wrappers, square bale
wrappers, round bale stackers, round bale handlers, bale shears, and bale stackers in a state
of the art 7,000m² production facility in the heartland of Ireland.
The E100 SA EcoWrap is the latest edition to the Tanco line of
trailed wrappers.
This model is targeted at small/medium sized operations that need
an affordable, reliable, yet versatile wrapper for round bales.
The machine is cable operated using 3 lever controls.
A key feature of this wrapper is the automatic hydraulic cut & start system. “One touch” bale
eject and cut system. When the tipping lever is engaged to eject the bale a unique hydraulic
cut and start function automatically activates at exactly the correct moment, to give a
perfectly finished bale.
TANCO BALE GRABS
The robust TANCO D70 ROUND BALER STACKER facilitates
stacking bales on their flat side. The bales are handled and rotated
90° and then stacked on their ends. This helps round silage bales
keep their shape better.
For a full listing of TANCO bale handling equipment available, please contact our FSME
Sales Team
DELIVERY ANYWHERE IN AUSTRALIA
Page 11
CARRYALLS
BERENDS
Made in Victoria.
0130
0135
0160
0162
6’ x 3’6” HARDWOOD FLOOR
4’ x 3’
HARDWOOD FLOOR
6’ x 3’6” METAL
4’ x 3’
METAL
FARM-AID
Made in Queensland.
FA500
6’ x 3’6” HARDWOOD FLOOR
FA501
6’ x 3’6” STEEL FLOOR
FA502
5’ x 2’6” HARDWOOD FLOOR
FA503
4’ x 3’
HARDWOOD FLOOR
FA504
3’ x 2’
HARDWOOD FLOOR
Custom built carryalls available upon request.
SILVAN
155SF1
4’ x 3’ CHECKER PLATE STEEL FLOOR
Size
4x3
Floor Material
Checker Plate Steel
Weight
62kg
Visit our website: www.fsme.com.au
Page 12
Need a pump or
generator
mounted on a
carryall.
Why not call
with your
enquiry
CEMENT MIXERS
TEAGLE SPIROMIX
3PL mixer suitable for stock feed, soils, seeds and cement.
Wide mouth for easy loading.
Drum rotates in one direction for mixing, and opposite for unloading. This is driven
by a hydraulic motor with a controller positioned at the tractor seat.
Good unloading height as the drum does not require tipping to unload.
STOCK CODE
100H
200H
DRUM VOLUME
280L
560L
MIX VOLUME (approx)
140L
280L
MIX WEIGHT (approx)
311KG
623KG
LOADING HEIGHT
35CM
48CM
WEIGHT (empty)
188KG
190KG
CAT 1 or 2
CAT 2
20
50
LINKAGE
MIN TRACTOR HP
COSMO CEMENT MIXER
Designed for, but not limited to concrete preparation.
Hopper/Cone - 320L large/open mouthed (3mm rolled, with
no welded seams).
Gearbox has chain transmission drive system
(10:1 reduction) in steel housing.
Linkage / Mounting by FIXED, BOLT ON CATEGORY 1.
Finished in premium quality agricultural enamel with epoxy
varnish.
Discharge / Tipping by 18” x 1.5” Hydraulic Cylinder.
Rotation - MIN: 250rpm MAX: 300rpm.
Made in Italy.
ELECTRIC CEMENT MIXER
CMIX-2275
0.74HP, 230 VOLT, 50Hz
2.2cu Ft CAPACITY
We manufacture a wide range of attachments to suit your needs Why not call us?
DELIVERY ANYWHERE IN AUSTRALIA
Page 13
COIL-TINE CULTIVATORS
BERENDS
The coil tines are 30mm square, and are used for primary and secondary cultivation.
Ideal where deep penetration is required without bringing subsoil to the surface.
The coil allows the tine to move, assisting penetration and reducing horsepower
needed.
Useful in pasture renovation and plough or rotary hoe pan breaking.
100 x 100 x 6mm frame.
Horsepower requirements vary but 8-10Hp per tine is a rough guide
0202
5 TINE COIL-TINE CULTIVATOR
0204
7 TINE COIL-TINE CULTIVATOR
0206
9 TINE COIL-TINE CULTIVATOR
0208
11 TINE COIL-TINE CULTIVATOR
0200
DEPTH WHEEL KIT
FARM-AID
The FARM-AID Coil-Tine Cultivators consist of a 2” square solid frame, heavy duty
headstock, clamps, wedges, 1” square double coil tines and points or sweeps with bolts &
nuts.
Assemblies can also be made to custom specification
CODE
CUT
TINES
SINGLE TOOLBAR
FA300
3’ 0” (.92m)
3
90kg
FA301
4’ 0” (1.2m)
4
110kg
FA302
5’ 6” (1.65m)
5
136kg
FA303
7’ 6” (2.25m)
7
170kg
CUT
TINES
FA300
5’ 6” (1.65m)
9
236kg
FA301
7’ 6” (2.25m)
9
300kg
FA302
10’ 0” (3.0m)
11
371kg
FA303
10’ 0” (3.0m)
15
400kg
CODE
DOUBLE TOOLBAR
Visit our website: www.fsme.com.au
Page 14
S-TINE CULTIVATORS
S-Tine Cultivators are one of the most versatile and valuable machines
a farmer can own. By working with the weather, an S Tine can be used
from primary cultivation to creating a seed bed.
BERENDS STANDARD S-TINE
The STANDARD S-TINE section is 32 x 10mm and is fitted to a 50 x
12 frame with gussets every 400mm. The headstock can be offset if
required for working under trees etc. The standard model has four rows of tines providing
extremely good trash clearance. Standard tines are 32 x 10mm Italian “shot peened”.
CODE
TINE
CUT
WEIGHT
HP REQ
0311
12
1.2m
118kg
0312
16
1.6m
0313
20
0314
OPTIONAL CRUMBLERS
CODE
WEIGHT
18-25
0235
75kg
154kg
18-30
0236
85kg
2.0m
172kg
20-40
0237
95kg
24
2.4m
199kg
25-50
0238
100kg
0315
28
2.8m
206kg
35-60
0239
120kg
0316
32
3.2m
233kg
40-70
0240
130kg
0317
36
3.6m
260kg
45-80
0241
140kg
0319
54
5.4m
80-100
0220
Wheel kit to suit 12-28 tine models
0230
Wheel kit to suit 32-36 tine models
(complete w/- crumbler, wheel
kit & hydraulic folding wings)
BERENDS HEAVY DUTY S-TINE
The HEAVY DUTY S-TINE is designed to be more primary cultivation orientated, than the
STANDARD model.
CODE
TINES
CUT
HP REQ
The HD S-TINE is 45 x 12mm Italian
“shot peened” and is fitted to a 50 x 50mm
frame.
They are ideal for working down hard
ground and pasture renovation.
0300
16
2.4m
35 +
0301
20
3.0m
45 +
0302
24
3.6m
55 +
0310
Wheel kit to suit HD models
DELIVERY ANYWHERE IN AUSTRALIA
Page 15
S-TINE CULTIVATORS
FARM-AID
Standard Models
FA120
3’ x 6 Tine Single Bar
FA121
4’ x 9 Tine Double Bar
MADE IN AUSTRALIA
DAKENAG
The S-TYNE cultivators are now galvanized (not painted) and are made in China at
Dakenag’s manufacturing complex.
MODELS AVAILABLE
61204DC
4’ - 2 ROW
61205DC
5’ - 2 ROW
61206DC
6’ - 2 ROW
03015S
4’ - 3 ROW
03019S
5’ - 3 ROW
03027S
6’ - 3 ROW
03035S
7’ - 3 ROW
03105D
4’ - 4 ROW
03100D
5’ - 4 ROW
03115D
6’ - 4 ROW
03110D
7’ - 4 ROW
Optional crumbler rollers, depth
wheel kits and “C” seeder mounting
brackets are also available.
Please refer to the Seeder section on
page 98 for easily mounted “C”
Seeders.
Visit our website: www.fsme.com.au
Page 16
S-TINE CULTIVATORS
JARRETT
Designed for light (ST) to medium-heavy (STH) cultivation, row cropping, ploughing,
raking and initial working of new country. Assists in controlling weed growth and surface
water penetration. Tynes can be re-arranged on tool bars and additional tynes can be added
to suit any application.
ST SERIES
MODEL
TYNES
WEIGHT
WIDTH HP REQ
ST150
5
125kg
1.5m
25
ST210
7
150kg
2.1m
35
ST270
9
175kg
2.7m
45
STH SERIES
Spring Tyne with “helper” spring
MODEL
TYNES
WEIGHT
WIDTH HP REQ
STH150
5
125kg
1.5m
25
STH210
7
150kg
2.1m
35
STH270
9
175kg
2.7m
45
Spring Tyne with wide point foot.
MODEL
TYNES
WEIGHT
WIDTH HP REQ
STH-V210
13
225kg
2.1m
45
STH-V270
17
270kg
2.7m
55
STH-V330
19
330kg
3.3m
65
Full range of replacement parts available. Please call the FSME Team
Mini Layer Raised Bed Plastic Mulch Layer
Will lay 4' plastic with 58" row spacing
Adjustable bed height from 3" to 5"
Requires minimum 30-hp with 4-wheel drive
Water tank to adjust weight to match tractor size
Compact machine for high tunnels.
Adjustable tension brake on plastic roll carriers
Replaceable, reversible plow share
3/8" & 1/2" UHMW poly lined bed press
Category 1 3 point hitch.
DELIVERY ANYWHERE IN AUSTRALIA
Page 17
DISC CULTIVATORS
Disc Cultivators (Ploughs) are still a popular cultivation tool with good reason. They break
up soil for preparing crops or controlling weeds.
BERENDS LINKAGE OFFSET
This medium duty offset disc is designed for small to medium size tractors. They are fitted
with 28mm (1 1/8”) square high tensile gang bolt axles and high quality triple sealed
bearings.
All Berends Discs are fitted with Bellota manufactured discs which have a Life-time warranty
for any manufacturing failure.
CODE
DISCS
WORKING HP REQ
WIDTH
0247
10
450 x 4mm
1125mm
30HP
0248
12
500 x 4mm
1350mm
36HP
0249
14
550 x 5mm
1600mm
42HP
0250
16
550 x 5mm
1825mm
48HP
0252
18
550 x 5mm
2050mm
54HP
GM40 LINKAGE OFFSET
The Gibbins Rawlings machine is a heavier duty version of the
Berends linkage model. It is ideal for all types of terrain
however it is most commonly used in market gardens, orchards
and for firebreaks, where the operator wants the strength and
weight of a large disc, but the versatility and compactness of a
linkage model.
Using solid cast iron disc spools instead of pipe spacers almost
doubles the weight of the machine. More weight gives better
penetration in hard ground.
CODE
DISCS
(560 x 5mm)
AXLES
WORKING
WIDTH
APPROX
WEIGHT
HP
REQ
OPTIONAL
SCRAPERS
CODE
0810
18
2
2060mm
820kg
45 +
0947
0811
20
4
2300mm
860kg
50 +
0948
0812
22
4
2500mm
910kg
55 +
0949
0813
24
4
2740mm
940kg
60 +
0950
Visit our website: www.fsme.com.au
Page 18
DISC CULTIVATORS
TH30 LINKAGE TANDEM
The TH30 is a similar model to the GM40 except that the four gangs are set up in a tandem
arrangement. The front two gangs throw out to either side, whilst the rear two gangs throw
the soil inwards. This set-up means that the operator doesn’t need to worry as much about
angle set-up, as each gang counter-acts the opposing gang resulting in an even pull.
CODE
DISCS
(560 x 5mm)
HP
REQ
OPTIONAL
SCRAPERS
CODE
0814
16
40 +
0946
0815
20
50 +
0948
0816
24
66 +
0950
RM40 TRAILING OFFSET
The RM40 is one of the most popular disc
cultivators on the market. It is ideal for all types of
terrain but particularly suited to cropping and
pasture renovation.
It suits the operators who don’t have the
horsepower, the acreage, or the money, to justify
a larger and heavier trailing model.
CODE
DISCS
(560 x 5mm)
AXLES
WORKING
WIDTH
APPROX
WEIGHT
HP
REQ
0820
16
2
1830mm
990kg
40 +
0821
18
2
2060mm
1040kg
45 +
0822
20
4
2300mm
1105kg
50 +
0823
22
4
2500mm
1170kg
55 +
0824
24
4
2740mm
1230kg
60 +
DELIVERY ANYWHERE IN AUSTRALIA
Page 19
DISC CULTIVATORS
RM75 TRAILING OFFSET
The RM75 is a heavier version of the RM40. It has great “digging” ability and is ideal for
primary and secondary tillage.
Prong scrapers are standard on this machine with formed scrapers available upon request.
CODE
DISCS
(610 x 5mm)
AXLES
WORKING
WIDTH
APPROX
WEIGHT
HP
REQ
0830
18
2
2060mm
1575kg
54 +
0831
20
2
2300mm
1650kg
60 +
0844
22
4
2500mm
1725kg
66 +
0832
24
4
2740mm
1930kg
72 +
0833
28
4
3200mm
2120kg
84 +
DISCS
(610 x 6mm)
AXLES
WORKING
WIDTH
APPROX
WEIGHT
HP
REQ
0840
18
2
2060mm
1575kg
54 +
0841
20
2
2300mm
1650kg
60 +
0845
22
4
2500mm
1725kg
66 +
0842
24
4
2740mm
1930kg
72 +
0843
28
4
3200mm
2120kg
84 +
CODE
Visit our website: www.fsme.com.au
Page 20
DISC CULTIVATORS
RM80 TRAILING OFFSET
The RM80 is virtually the same machine as the RM75 with the main difference being in the
greater number of bearings and shorter axles in the disc gang assemblies.
CODE
DISCS
WORKING HP REQ
WIDTH
0850
20
610 x 5mm
2300mm
60 +
0851
24
610 x 5mm
2740mm
72 +
0852
28
610 x 5mm
3200mm
84 +
0853
32
610 x 5mm
3660mm
96 +
0860
20
610 x 6mm
2300mm
60 +
0861
24
610 x 6mm
2740mm
72 +
0862
28
610 x 6mm
3200mm
84 +
0863
32
610 x 6mm
3660mm
96 +
0870
20
660 x 6mm
2300mm
60 +
0871
24
660 x 6mm
2740mm
72 +
0872
28
660 x 6mm
3200mm
84 +
0873
32
660 x 6mm
3660mm
96 +
If you are looking at this Catalogue on line, why not contact us for your FREE
COPY or else please fill in details to be able to download this as a file.
DELIVERY ANYWHERE IN AUSTRALIA
Page 21
DISC CULTIVATORS
TH100 TRAILING TANDEM
The TH100 is a similar model to the RM80 except
that the four gangs are set up in a tandem
arrangement. The front two gangs throw out to
either side, whilst the rear two gangs throw the soil
inwards.
Designed in Australia to suit harsh conditions, the
TH100 tandem disc will track straight and not
present problems with side draught.
The TH100 has great digging ability making it
ideal for both primary and secondary tillage on 90 - 170HP tractors.
The wheel kit on the TH100 consists of four Landcruiser (750 x 16) wheels controlled by a
hydraulic ram. It is also fitted standard with a parking jack and formed scrapers which are
individually curved to suit the disc.
The drawbar is fully adjustable for mounting to different height tractors and fitted with
a high parallel lift for better transportation.
Available as non-folding and also hydraulic folding. All models of the hydraulic folding
design are fitted with hydraulic gang adjustment which allows the gangs to be folded
parallel with the main frame to be under 2.4m in overall width.
DISCS
(610 x 5mm) or
(610 x 6mm) or
(660 x 6mm)
BEARINGS
AXLES
WORKING
WIDTH
APPROX
WEIGHT
28
8
4
3430mm
2450kg
32
12
4
3880mm
2660kg
36
16
8
4330mm
2840kg
40
16
8
4800mm
2990kg
44
16
8
5260mm
3310kg
48
16
8
5710mm
3460kg
Visit our website: www.fsme.com.au
Page 22
D
DISC CULIVATORS
MURRAY & SON
The Murray SERIES 32 disc harrow is a simple yet rugged
linkage mounted tillage implement suited to many
applications. The versatility is highlighted by the
Implement’s three possible working configurations: standard
4-gang (rigid), 4-gang (rear section floating) and 2-gang
(rear gangs removed).
JARRETT
The Jarrett LINKGAGE DISC SERIES have been designed for light-medium (BS) and
medium-heavy (CS) secondary tillage applications, such as orchard & vegetable farming,
general farming, weed control and fire breaks.
CODE
DISCS WEIGHT
WORKING
WIDTH
HP
REQ
BS1218
12
312kg
1400mm
25
BS1418
14
366kg
1600mm
35
BS1618
16
398kg
1800mm
45
WORKING
WIDTH
HP
REQ
CODE
DISCS WEIGHT
CS1420
14
500kg
1600mm
40
CS1620
16
550kg
1800mm
50
CS1820
18
630kg
2000mm
60
CS2020
20
690kg
2300mm
70
BS SERIES
CS SERIES
FSME have a large range of Rain Guages available. Please check our
website www.fsme.com.au or call one of our Sales Team Members to
discuss.
DELIVERY ANYWHERE IN AUSTRALIA
Page 23
DISC CULTIVATORS
The Jarrett TRAILING DISC SERIES have been designed for robust primary and secondary
tillage, fallow ploughing and stubble mulching.
CODE
DISCS WEIGHT
WORKING
WIDTH
HP
REQ
TD1624
16
1600kg
1800mm
65
TD1824
18
1700kg
2100mm
70
TD2024
20
1800kg
2300mm
75
TD2224
22
1900kg
2500mm
80
TD2424
24
2000kg
2700mm
85
TD2624
26
2100kg
2900mm
90
TD2824
28
2200kg
3200mm
95
WORKING
WIDTH
HP
REQ
CODE
DISCS WEIGHT
JT2426
24
2500kg
2750mm
90 +
JT2826
28
3000kg
3200mm
110 +
JT3226
32
3500kg
3650mm
130 +
JT3626
36
4000kg
4100mm
150 +
X300 SHEEN FLAME GUN
Turn to Page 49 for more information
The ultimate way to eradicate
unwanted and noxious weeds along
with other parasites without using
potentially dangerous chemicals
Visit our website: www.fsme.com.au
Page 24
TD SERIES
JT SERIES
DAIRY SCRAPERS / SMUDGERS
BERENDS
The 6’ Medium Duty Smudger is designed for cleaning muck and waste from concrete
floors. Particularly suited to dairy applications.
All components are derived from the 6’ Medium
Duty Grader Blade. By simply removing the
bolt-on wings and fitting a reversible cutting
edge, the smudger can easily be converted back
to a grader blade.
8mm thick mouldboard fitted with 20mm thick
steel reinforced rubber smudger edge.
Fitted with positive quick release centre for
angle selection, to minimize wear and tear. Allows 24 different angle positions.
Blade can be reversed for back filling.
Can be offset within seconds to work outside the tractor wheel to the left or right
hand side. Choice of 5 positions each way to a maximum of 600mm offset.
Optional pneumatic wheel kit available for depth control.
CODE
DESCRIPTION
0399
6’ MD model with 45degree wings & rubber
0380
10’ trailing model with hydraulic wheel kit
NEW ZEALAND MANUFACTURED SUPASCRAPERS
Developed and manufactured in New Zealand, the Supascraper is the fast and easy way to
move large amounts of effluent in dairy yards. Pulling down on the handle lifts the scraper
clear for back-up runs.
Cut hosing time and water usage to a
minimum.
Light weight for mobility.
All galvanized construction.
QUALITY AND SERVICE
is
OUR MOTTO
DELIVERY ANYWHERE IN AUSTRALIA
Page 25
DELVER & DRAIN DIGGERS
BERENDS
The DELVER is mainly designed for vineyard or orchard use however some have been
purchased for other purposes, such as cleaning out channels in irrigation country.
In the vineyard application, it is ideal for cleaning the ground between the vines and
mounding the soil back onto the base of the vines. It is most effective if the soil has been
cultivated previously and is not compacted.
The delver consists of two mouldboards (350 x 1800 x 6mm) which are able to be adjusted
to suit different row widths. Each one is fitted with an extension which can be adjusted for
length and can provide an overall standard width of 3 metres (other widths are also available).
A 12” furrower on the front is designed to penetrate the
ground depending on the set-up of the top link.
A series of top link mounting holes allow for “fore” and
“aft” angle adjustment enabling either a flat drain or a
V-drain to be cleaned.
The DRAIN DIGGER manufactured by Berends is arguably the best on the market.
It is fitted with a series 5 Italian PTO shaft with an integrated 2 plate adjustable slip clutch,
driving a 2” high tensile drive shaft with two 2” self aligning bearings.
The rear drive plate is bolted to a welded flange, unlike some of the others which use keys
or splines (these inevitably “chop out” in time).
The real key is the blades, which are made in house from Bisalloy (an abrasive resistant steel).
These blades are 130 x 10mm thick and are shaped especially
for drain digging.
The machine is fitted with an adjustable foot which can be
controlled from the tractor.
Tractor HP required: 50HP +
Weight approximately: 210kg
Visit our website: www.fsme.com.au
Page 26
DIESEL TANKS & ACCESSORIES
SILVAN SELECTA DIESEL PRO
The Diesel Pro diesel transfer units are available in 200,
400 and 600 litre capacities. The tanks are manufactured
with a unique diesel grade polyethylene that is UV
stabilised and impact resistant. The colour grey denotes
diesel. The heavy duty reliable 12 volt pumps are made
in Italy by Piusi, a world class pump manufacturer.
Also features a lockable filling cap, designed for easy
strapping and a lockable cover.
CODE
OPEN
FLOW
DIMENSIONS
(L x W x H)
WEIGHT
SQDN200L-X1 200L DIESEL PRO
45L/min
1100 x 640 x 640
27kg
SQDN400L-X1 400L DIESEL PRO
45L/min
1700 x 820 x 590
41kg
SQDN600L-X1 600L DIESEL PRO
45L/min
1664 x 840 x 810
50kg
PF11-X2
DESCRIPTION
OPTIONAL ELECTRONIC DIESEL METRE
SILVAN SELECTA DIESEL POWER
The rugged Selecta 12 volt Diesel Power transfer units are
available from 50 to 300 litre capacities. As with the
Diesel Pro, the tanks are manufactured from a unique diesel
grade polyethylene that are impact resistant and
UV stabilised. Proven and reliable Selecta Diesel Power
pumps are the heart of this rugged product.
CODE
DESCRIPTION
OPEN
FLOW
DIMENSIONS
(L x W x H)
WEIGHT
(dry)
SQD50-1
50L
14L/min
700 x 400 x 300
8kg
SQDN100-1
100L
40L/min
800 x 620 x 440
18kg
SQDN200-7
200L
40L/min
1100 x 640 x 550
24kg
SQDN300-7
300L
40L/min
1060 x 900 x 530
30kg
DELIVERY ANYWHERE IN AUSTRALIA
Page 27
DIESEL TANKS & ACCESSORIES
SELECTA DIESELPAK
The rugged Selecta 12 volt DieselPak transfer units are
available from 200 to 2200 litre capacities. The tanks are
manufactured with a unique diesel grade polyethylene that is
UV stabilized and impact resistant. The heavy duty pumps
are made in Italy by Puisi.
Standard Specifications
4 metre wiring harness with alligator clips
4 - 5 metre ¾” delivery hose with auto shut-off
trigger
Pump mounting plate standard on 300L - 1000L
1000L and 2200L tanks moulded feet to suit
optional bolt down kit
Options Available
10m retractable reel kit
DieselPak digital diesel litre counter
Short and Long frame skids
For specific information on each size available, please contact a member of the
FSME Sales Team
SELECTA DIESEL HD
The Diesel HD is Australia’s most feature rich diesel
transfer unit designed for the security conscious user
with fully lockable pump cover and filler cap.
Incorporated is an AdBlue®¹ tank, making this unit a
complete refuel point for Euro 5 approved vehicles.
The HD is designed for improved tie-down or rope
mounting to vehicle or deck to ensure that the tank
remains stable in transit.
Available in 320 litre capacity with 45L/min open flow.
Visit our website: www.fsme.com.au
Page 28
DIESEL TANKS & ACCESSORIES
SELECTA AIRPOWER DIESEL
The AirPower diesel unit is a spark free option for diesel fuel
transfer in hazardous work environments such as mining and
construction sites. The AirPower unit only needs a connection
to a suitable compressed airline to begin fluid transfer.
Average air consumption 0.2cm³
4 metre, ¾” delivery hose with auto shut-off trigger and
hose swivel
Spark-free operation
Impact resistant UV stabilised diesel grade polytuff
tank
Baffled tank
Available in 400 litre capacity with 60L/min open flow
SELECTA DIESEL ACCESSORIES
12 volt high flow pump
Digital litre counter kit
Mechanical diesel counter
12 volt pump kit
Retractable hose reel & hose
Large Range of Diesel Tanks
including Custom Built Stands
For a comprehensive list of accessories available in the diesel range, please contact a
member of the FSME Sales Team
DELIVERY ANYWHERE IN AUSTRALIA
Page 29
DOLOMITE DROPPERS & DRUM LIFTERS
FARM-AID
DOLOMITE DROPPERS
3 point linkage mounted
Ground wheel drive
Adjustable hole openings and
agitator to ensure free flow of
fertilizer and lime
Optional trailing models
available upon request
CODE
DESCRIPTION
FA850
MINI 3’ (900mm)
FA851
JUNIOR 4’ (1200mm)
FA852
STANDARD 6’ (1800mm)
FA853
LARGE 8’ (2400mm)
FA854
EXTRA LARGE 10’ (3000mm)
FA855
DRAWBAR (Manufacturing Option)
FARM-AID DRUM LIFTERS
The ideal fork lift attachment.
Reduces risk of injury through manual
handling.
Reduces risk of waste and spillages of
contents.
CODE
DESCRIPTION
FA1013
Manual
FA1014
Hydraulic
Visit our website: www.fsme.com.au
Page 30
MADE IN AUSTRALIA
FENCING & DRILLING
BERENDS POST HOLE DIGGERS & AUGERS
All post hole digger drive-shafts are made in Italy (Bondioli & Pavesi) and are fitted with
integrated clutches which are much more superior compared to a separate clutch, as there are
less wearing parts involved and tolerances are much higher.
Heavy duty PTO shafts with a torque limiting clutch are mounted at the tractor end to protect
the PTO in the event of the tractor rolling forward or backwards when the PTO is engaged.
The drivetrain is matched so that the clutch
disengages well before the capacity of the gearbox
has been reached.
5 YEAR
WARRANTY ON
ITALIAN
GEARBOXES
Handy Tips for Extremely Hard Conditions:
Avoid digging in the driest season of the year.
Use a small auger to dig a pilot hole first
before going to a larger auger.
Fill the half dug hole with water and let it sit
overnight before completing the hole.
Comprehensive range of spare parts and consumables available.
MODEL
PTO SHAFT
GEARBOX
COMPACT
(0258)
STANDARD
(0259)
HEAVY
DUTY (0261)
Series 3/L2 torque Series 3/L2 torque
Series 3/L3
limiting clutch
limiting clutch
torque limiting
clutch
40 HP
40 HP
85 HP
MAIN FRAME
100 x 50 x 6mm
89 x 89 x 5mm
RHS
89 x 89 x 5mm
RHS
TRACTOR HP
16 - 30
20 - 50
30 - 100
AUGER SIZES
SUITABLE
4” - 12”
6” - 12”
6” - 24”
NETT WEIGHT
(less auger)
85kg
95kg
130kg
DELIVERY ANYWHERE IN AUSTRALIA
Page 31
FENCING & DRILLING
BERENDS HYDRAULIC DOWN PRESSURE POST HOLE DIGGER
Ideal for penetrating hard ground as the A frame is extended above the boom and a hydraulic
ram (2 ½” x 8”) is fitted between this extension and the boom to achieve a weight transfer of
approximately 1000kg.
MODEL
0262
PTO SHAFT
Series 3/L3 torque
limiting clutch
GEARBOX
85 HP
MAIN FRAME
100 x 100 x 6mm
TRACTOR HP
30 - 100
AUGER SIZES SUITABLE
6” - 24”
NETT WEIGHT (less auger)
150kg
BERENDS PLANETARY POST HOLE DIGGER
Instead of using a PTO driven gearbox, the unit is fitted with a heavy duty European
Planetary Drive.
Therefore, the tractor requires 2 pairs of hydraulic remotes to operate the machine.
This type of set-up is safer than regular models as it eliminates the need for a PTO shaft
and no clutch is required.
The gearbox can also be operated anti-clockwise if entangled in roots simply by reversing
the oil flow.
MODEL
0260
TORQUE
2,452nm
OIL FLOW RANGE
27 to 75l/min
MAX PRESSURE
205 Bar
MAIN FRAME
100 x 100 x 6mm
TRACTOR HP
30 +
AUGER SIZES SUITABLE
6” - 24”
NETT WEIGHT (less auger)
150kg
Visit our website: www.fsme.com.au
Page 32
FENCING & DRILLING
TRIMAX HEAVY DUTY AUGERS
Suit hydraulic models of the Berends range.
Complete cast steel head with teeth set at aggressive 45 degree angle.
Fitted with tri-flow pilot for more effective guiding of the auger and stabilizing the tip
in hard conditions.
Less pitch on flights which allows for easy flow of dirt from the hole.
As with Standard augers, Trimax are available in 4” - 24” clockwise models.
KANGA POST HOLE DIGGERS & AUGERS
Kanga offers two designs (Single Boom or Dual Rail Boom) and three (3) Gearbox
transmissions for 3PL Tractor Post Hole Diggers.
MINI RANGE (52000)
The standard “Single Boom” Post Hole Digger is offered in
a compact (for compact and sub-compact tractors up to
30HP) with a 35HP rated Gearbox.
Augers available from 4” to 12”.
M RANGE (51000)
The standard “Single Boom” Post Hole Digger is offered with a 50HP rated Gearbox.
Augers available from 4” to 24”.
H RANGE (50000)
The standard “Single Boom” Post Hole Digger is offered with a 75HP rated Gearbox.
Augers available from 4” to 24”.
XH RANGE (56000 - 50HP & 55000 75HP)
The XH Range is a Hydraulic Down Pressure
Post Hole Digger with a “Dual Rail Boom”
design. It is available in both 50HP and
75HP Gearbox transmissions and is ideal in
situations where the ground is hard and the
auger needs some additional assistance.
DELIVERY ANYWHERE IN AUSTRALIA
Page 33
FENCING & DRILLING
Suits A6
Suits AGT,
AGS,A7T
Suits A5
Suits A4
Suits A1,A3
DIGGA WEARPARTS
HEAVY CONDITIONS
STANDARD CONDITIONS
LIGHT CONDITIONS
Compacted soils, heavy clay,
asphalt, concrete, frozen ground
& soft rock
Long wearing, moderate ground
conditions. Flat Tungsten carbide
braised to wear part for longer life.
Light to moderate ground
conditions
TS-3
TS-C-3
PS-3
TS-2
TS-C-2
PS-2
TS-1
TS-C-1
PS-1
TS-3
TS-C-3
PM-3
TS-2
TS-C-2
PM-2
TS-1
TS-C-1
PM-1
TS-3
TS-C-3
PM-SQ-3
TS-2
TS-C-2
PM-SQ-2
TS-1
TS-C-1
PM-SQ-1
C1095
TTC-3
PM-SQ-3
TM-3
TM-C-3
PM-SQ-3
For all your Digga Auger & Conversion Head
requirements,
contact a member of the FSME Sales Team
TM-2
TM-C-2
PM-SQ-2
TM-1
TM-C-1
PM-SQ-1
Suits A8
Large range of wear parts available to suit
all your attachments.
Suits A9,
A10, A11
TM-3
TTD-3
TM-C-3
TTS-3
PM-HX-3
TTL3
PH3
Genuine OEM Spare Parts
Visit our website: www.fsme.com.au
Page 34
FENCING & DRILLING
BERENDS POST DRIVER (0263)
The Berends Post Driver was originally designed to provide a more
affordable driver to the agricultural market. Based on a simple but
strong designs, the post driver runs off a single set of remote hydraulics.
No plumbing into the back axle is required. The hydraulic ram
(2 ½” x 8”) controls a lever arm which is connected to the weight by a
100 cable. The dolly weight is approximately 160kg and is capable of
driving a 6’6” post (with the driver on the ground). As the weight is
basically a free falling mass, Berends don’t need to fit as heavy a weight
as other brands as they often have some friction resistance in the way
they are operated.
There is a safety cage fitted around the unit as required by OH&S
regulations. The cage is a two part cage which enables the lower
section to be opened up when using in existing fence lines.
The overall height of the machine is 3.9m whilst the weight is
approximately 450kg. The tractor using this machine will have to be
capable of lifting this weight.
PEERLESS PNEUMATIC POST / PICKET DRIVER
Makes a hard job easy. The Peerless Pneumatic Post Driver has
been designed in the United States for over the last 10 years.
The driver is of an all steel construction to ensure a long life in
the harshest conditions.
Unlike most other drivers on the market, the Peerless does not
require large volumes of air to operate. Any 5.5HP petrol
driven compressor will easily drive posts into the hardest
ground.
CAPACITY
Round Post - 55mm
Square Post - 54mm
Additional mandrels available
MAX PSI
70 - 80
WEIGHT
14.2kg
AIR DELIVERY (LPM)
85 - 142
AIR DELIVERY (CFM)
3-5
TRAVEL
175mm
PERFORMANCE
80 - 85 strokes per minute
MADE IN USA
DELIVERY ANYWHERE IN AUSTRALIA
Page 35
FENCING & DRILLING
Fencing around your property is worth thousands of dollars.
Save your wire and re-use it for repairing or making new fences.
HYDRAULIC WIRE WINDER
Designed for smooth or barbed wire
Heavy duty hydraulic motor with hoses & shut - off valve
Adjustable speed to roll or unroll wire
Hand spun steel cone splitting reel designed with safety in mind. Non - split reels
also available
When the reel is full, tie the roll with 3 tie wires used on the 3 different positions
of the reel and then split the reel and remove the roll.
PTO WIRE WINDER
PTO shaft driven
Automatic tensioning ensures firm wire rolls
Traverse eye to give well formed rolls
Fits any tractor linkage
Rewinds and spins out wire without kinks
Reclaimed wire coil dimensions - 600mm ID x 900mm OD x 150mm DEEP
TECHFENCE ELECTRIC FENCING ENERGISERS
The Techfence range of Electric Fence Energisers is the culmination of
over 40 years of experience in Australian electric fencing. Featuring
real cutting edge technology, balanced with a robust, functional design.
Many more products available for the new project on your
property or simply just for maintenance and repairs.
To discuss your individual needs please contact a member
of the FSME Sales Team
Visit our website: www.fsme.com.au
Page 36
FERTILISER SPREADERS
Fertilisers are applied to promote plant growth and increase soil fertility. They have been
known to increase yields by 30 - 80%, thus increasing crop production and improving the
quality of food and fodder.
SOLO 421 PORTABLE GRANULATE SPREADER
The integral agitator ensures even distribution onto the steadily turning
spreading disc driven by the manual crank.
Up to 9kg of granulated material can be applied where specifically
required, even on difficult to reach terrain.
The spreader is carried in front of the body by means of an individually
adjustable strap.
The large filler opening makes filling easy, whilst the large screw top protects users from
harmful dust.
Suitable for spreading seeds, fertilizer, oil absorbers, cleaning agents, pelletised lime, bird
seed, wildlife feed and sand.
EARTHWAY PUSH AND TOW SPREADERS
Ease your work load with this high grade spreader from
EV-N-SPRED manufactured in USA.
CODE
DESCRIPTION
FEATURES
2000A
PUSH BROADCAST
SPREADER
18KG HOPPER
2050P
PUSH BROADCAST
SPREADER
40KG HOPPER
7350
PUSH DROP SPREADER
27KG HOPPER
2050T
TOW BROADCAST
SPREADER
40KG HOPPER
2050TP
TOW BROADCAST
SPREADER
40KG HOPPER
PNEUMATIC
WHEELS
DELIVERY ANYWHERE IN AUSTRALIA
Page 37
FERTILISER SPREADERS
SILVAN SUPERPAK ATV SPREADER (SP60-1)
12 Volt DC Compact spreader with attachment frame
60 litre (70kg) non-corrosive hopper with easy load
flip-up lid
Quick attach frame system
Rate adjustment lever
Electric on/off control box
4 blade spinner
304 stainless steel feed gates
SILVAN ECONOMY ATV TRAILED SPREADER
(SP150)
Quality grease packed gearbox and two piece
cast aluminium housing
4 adjustable spreading vanes each with 3
settings
Simple, single lever rate control
Mechanical spindle agitation
Adjustable drawbar - 5 height positions
150 litre capacity
6 - 12m width of spread
SILVAN TS SPREADER (TS-500GALHOP)
Differential type gear box ground drive with neutral
3 settings for spreading pattern - left, right & full
Suitable for compact tractors (up to 30HP) and
some ATV motorbikes
338 litre capacity
6 - 12m width of spread
Visit our website: www.fsme.com.au
Page 38
FERTILISER SPREADERS
SILVAN PTO POLY HOPPER SPREADER (PL-500)
Suitable for small to medium spreading applications
Capable of spreading a wide variety of products including fertiliser and seed
UV stabilized polyethelene hopper which is resistant to corrosion
Cat 1 three point linkage
PTO drive shaft with approved safety cover
Grease packed single speed gearbox with cast aluminium housing
One manual control lever is calibrated for quantity of application
Second control lever offers 3 settings for spreading pattern - left, right and full
345 litre capacity
6 - 18m width of spread
Optional Accessories
* One sided conveyor
* Two sided conveyor
* Agitator
* Hopper grid cover
* Extended control lever
* Hopper cover
MOST POPULAR
SPREADER ON THE
MARKET TODAY!
DELIVERY ANYWHERE IN AUSTRALIA
Page 39
FERTILISER SPREADERS
SILVAN SX SPREADER
Available with Galvainsed Hopper
(SX-500GALHOP) or Painted Hopper (SX-500)
Suitable for small to medium spreading applications
Capable of spreading a wide variety of products
including fertiliser and seed
Hopper manufactured from single piece of spun,
seamless steel
Support frame constructed of pressed and tubular
steel
Cat 1 three point linkage
PTO drive shaft with approved safety cover
Grease packed single speed gearbox with cast
aluminium housing
One manual control lever is calibrated for quantity
of application
Second control lever offers 3 settings for spreading
pattern - left, right and full
338 litre capacity
6 - 18m width of spread
Optional Accessories
Side throw conveyor
Agitator
SILVAN OS OSCILLATING SPREADER
Designed for precise application of fertiliser and seed at medium to low rates
Accurately applies producing twin bands (left and right) beneath trees in orchards
whilst also being able to apply full coverage for top dressing
Non-corrosive UV stabilized impact resistant polyethylene hopper
Continuous stroke fly wheel, rubber shock absorbers, counter balanced crank driving
oscillating spout & agitator
No gear, chain or belt
Cat 1 & 2 three point linkage
Available in 400 or 700 or 900 litre capacities
6 - 24m width of spreading
Visit our website: www.fsme.com.au
Page 40
FERTILISER SPREADERS
COSMO PTP TOW TYPE SPINNER SPREADER
Low profile metal hopper with floatation tyres
on a wide wheel base
“Dog gear” utilised to engage / disengage
spinner plate
Anti rust coated spinner disc with 6 fins
Single speed ground driven 1:1 ratio gearbox
Manual cable operation discharge
Available in 165 litre (213kg) or 260 litre (335kg) capacities
14 - 16m width of spread
COSMO PTB TOW TYPE SPINNER SREADER
Heavy duty PVC hopper with tubular frame on
floatation tyres
Stainless Steel spinner plate with 6 fins
Single speed ground driven 1:1 ratio gearbox
Manual split levers with lateral drop
Available in 165 litre (213kg) or 260 litre (335kg)
capacities
14 - 16m width of spread
COSMO P & PL SERIES 3PL SPINNER SREADER
Metal hopper supplied on P Series whilst PVC hopper
supplied on PL Series
Stainless Steel spinner plate with 6 fins
Single speed 540 RPM 1:1 ratio gearbox
Series 2 (21hp/16kw) triangular tube PTO shaft with safety
cover
Fixed category 1 bolt on pin mounting
Side drop onto spinner fins for even distribution discharge
P Series available in 269 litre (347kg) or 361 litre (466kg) capacities
PL Series available in 297 litre (383kg) or 361 litre (466kg) capacities
DELIVERY ANYWHERE IN AUSTRALIA
Page 41
FERTILISER SPREADERS
COSMO PENDULUM SUPER SPREADER
Traditional heavy duty fiberglass hopper with
strong reinforced frame
New generation flywheel (1:1 ratio) with a key
adjustment gearbox
Fixed category 1 linkage mounting
Manual lever discharge standard
(hydraulic option available)
Available in 480, 580, 850, 1050 & 1250 litre
capacities
0.75 - 15m width of spread (machine standard with 9 - 15m spout)
CRUMP “KURRAJONG” TRAILING PTO DRIVE SPREADER
Crump spreaders are primarily designed to accurately spread dry free running fertilisers
up to 1500 Lts / Ha.
PTO drive
2mm Stainless Steel hopper
Non-corrosive painted main chassis
Single tongue tow coupling for 19mm pin in tractor tow clevis
10.50 - 15 off road remould tyres fitted standard
Available in Standard & Deluxe & in 1, 2 & 3 tonne models
Deluxe models include adjustable discharge spout & gate assembly
Australian Made with
Australian materials
and good, old fashion
Aussie know how!
Visit our website: www.fsme.com.au
Page 42
FERTILISER SPREADERS
CRUMP “ACACIA” 3 POINT LINKAGE PTO DRIVE
SPREADER
Crump spreaders are primarily designed to accurately
spread dry free running fertilisers up to 1500 Lts / Ha.
PTO drive
2mm Stainless Steel hopper
Non-corrosive painted main chassis
Available in Standard & Deluxe & in 1, 1.5 & 2
tonne models
Deluxe models include adjustable discharge spout & gate assembly.
VICON PENDULUM SEEDER / SPREADER
More than one million machines sold prove that the Vicon pendulum seeder/spreader is the
first choice wherever the demand is for maximum accuracy in fertilizer application.
Spreading quality and ease of operation of this unique machine are unequalled - as now and
as in the past.
The pendulum movement of the spout ensures that
the application rate is always identical on both
sides. This results in an excellent overlap.
Features:
Optimized frame with no corners where
fertiliser can accumulate
Glass fibre reinforced polyester hopper
which is unaffected by aggressive types of
fertiliser
Stainless Steel metering disc
Unique Duracoat powder painting system
for exceptional corrosion resistance of spreading unit and frame
Specially designed calibration container available for making it no longer necessary to
remove the spout for calibration
Agitator ensures an even material feed to the spreading unit so there is no risk of the
fertiliser being crushed
Hopper can be easily moved under a tipping trailer or silo or filled by hand
Up to 18m width of spread
DELIVERY ANYWHERE IN AUSTRALIA
Page 43
FERTILISER SPREADERS
VICON TWIN DISC SPREADERS
The Vicon RotaFlow Twin Disc spreaders are
available in Compact, Medium and Extra
Large models.
RotaFlow RO-C - Compact & Complete
Controlled either manually or hydraulically.
It is the most compact spreader in the range,
but features all elements of the RotaFlow
spreader line. This results in a triangular
spreading pattern up to 21 metres.
All vanes for 9 - 18 metres (20/21m optional) working width
700 - 1,400 litres hopper capacity
RotaFlow RO-M - Master in the Medium Segment
Each spreading disc has 8 vanes & their length determines the working width of the machine.
These 8 vanes contribute to the highly accurate spread pattern across the complete working
widths. Both discs can be shut off independently to spread half the working width, essential
for preventing lodging in tapering headlands.
All vanes for 10 - 24 metres (27/28 optional) working width
1,100 - 2,000 litres hopper capacity
RotaFlow RO-XL - Large Working Widths, Bigger Volumes
The high capacity spreader of the RotaFlow range. The standard machine can spread all
working widths without changing discs, vanes or even gear wheels. The working width is
set using the tractor PTO speed and dual input shafts on the spreader centre gear box.
An innovative driveline to each disc ensures gentle agitation due to the “slow rotating”
agitator system, which runs at 15% of the spreading disc speed.
12 - 45 metres working width
1,500 - 3,900 litres hopper capacity
For further technical information on the RotaFlow range, please contact a member
of the FSME Sales Team
Visit our website: www.fsme.com.au
Page 44
FIRE CONTROL & FIGHTING EQUIPMENT
FIRE CONTROL “DRIP” TORCHES
Ideal for burning fire breaks and back burning
Lightweight aluminium body
Safe, simple & quick to operate
Available with either fixed wand (FCT1)
or retractable wand (FCT2)
Replacement parts readily available
SILVAN / SELECTA WATER TRANSFER / FIRE FIGHTING PUMPS
The Selecta Power Water Transfer Pumps are designed to handle all kinds of high volume
water pumping. They are ideal for applications where
portability is a must or electrical supply is a problem.
SELECTA POWER FIRE FIGHTING PUMP (LBA-100)
The Selecta Power pump/engine unit is ideal for fire fighting and watering, and comes
standard with a carry/mounting frame for increased mobility
and added protection.
4 stroke over head cam engine with oil alert
Max. 250 L/min open flow
Max. 100psi pressure
Direct coupled centrifugal, twin impeller fire fighting
pump
Maximum suction lift 3.5 metres
1 x 1½” inlet, 2 x 1” outlet and 1 x 1½” outlet
Optional hose kit (LBA-100A) consisting of 20m fire
fighting hose, nozzle, 6m suction hose and foot filter
SELECTA FOUR STROKE COMPACT WATER PUMP (LBA-115)
Portable centrifugal water pump - petrol powered (no mixing)
Ideal for fire control, watering and washing
115 L/min open flow / 40psi max pressure
3 metres of suction hose
Outlet and inlet connections 1” BSP
For further information on all models available please contact a Sales Team member
DELIVERY ANYWHERE IN AUSTRALIA
Page 45
FIRE CONTROL & FIGHTING EQUIPMENT
SILVAN / SELECTA FIRE CONTROL UNITS
“Thou shall extinguish every ember”
SELECTA POWER 300 LITRE FIRE CONTROL UNIT (SQF300C)
Made from thick UV Stabilised Polyethlene, with large
breather lid, strainer basket and internal baffle. Compact in
size and ideal for fire fighting, wash down and watering.
Engine:
4 stroke Selecta Power Engine
1.21hp Single Cylinder 33.5cc
Manual recoil rope start
Single element air filter
Max output 115L/min, Max pressure 40psi, Max head 25m
Fuel Tank:
0.6 litre capacity (unleaded)
70min operation duration (at full throttle)
3½hours (transfer at idle)
Hose:
20m of 19mm ID delivery hose with adjustable fire fighting nozzle
HONDA/DAVEY 400 LITRE FIRE CONTROL UNIT (SQF400)
These motorized fire fighting units feature the Davey Fire Fighting pump 425L/min open
flow (580kPa / 80psi) powered by the GX160 5.5HP Honda
engine.
Features:
Baffled design to reduce surge when travelling
Fits neatly in 1 tone trays
Screw down lid with breather
Calibrated sight line
The Squatpak designed tanks are available with your choice of hose kit or reel:
Hose kit: 20metres ¾” fire fighting hose with poly fire fighting nozzle
Hose reel: 30metres ¾” fire fighting hose with poly fire fighting nozzle
Visit our website: www.fsme.com.au
Page 46
FIRE CONTROL & FIGHTING EQUIPMENT
SELECTA POWER 800 LITRE FIRE FIGHTING UNIT (SQF800S-1)
6.5HP Selecta Power fire fighting engine with high pressure, twin impeller, fire
fighting pump
Hose reel with 30metres ¾” hose and fire fighting nozzle
Unique baffle design to reduce surge when travelling
Screw on lid with breather
Calibrated sight lines
Optional quick fill suction kit
HONDA/DAVEY 800 LITRE FIRE FIGHTING UNIT (SQF800D & -1)
Davey Fire Fighting Pump 425L/min open flow
(580kPa/80psi) powered by GX160 5.5HP Honda engine
Baffled design to reduce surge when travelling
Screw down lid with breather
Calibrated sight lines
The Squatpak designed 800L tanks are available with your
choice of hose kit or reel:
Hose kit: 20metres ¾” fire fighting hose with poly fire fighting nozzle
Hose reel: 30metres ¾” fire fighting hose with poly fire fighting nozzle
1100 LITRE FIRE FIGHTING SLED WITH HOSE REEL
1100L SELECTA POWER (SLF1000S-1)
6.5HP Selecta Power Engine
Max output 250L/min open flow
Max pressure 100psi, Max head 60 metres
Twin impeller - alloy
Manual recoil rope start
Complete with zinc plated
Hose Reel with 36m of
19mm fire fighting hose.
1100L HONDA/DAVEY (SLF1000D-1)
5.5HP Honda engine
Max output 425L/min open flow
Max pressure 80psi, Max head 75 metres
Single impeller - marine grade aluminium
Manual recoil rope start
Low oil protection
DELIVERY ANYWHERE IN AUSTRALIA
Page 47
FIRE CONTROL & FIGHTING EQUIPMENT
500 & 800 LITRE TRAILBLAZER SKID
FIRE FIGHTER
500 & 800 litre quality UV stabilized
poly tank with full drainage sump
Fast fill suction hose and filter
6.5HP Honda GX200 / Davey Pump single impeller
Heavy duty hose reel with 36m of
20mm hose and adjustable fire nozzle
Tie down points
Fast fill suction hose & filter
Heavy duty ZINC PLATED frame
ON-ROAD & OFF-ROAD 800 & 1000 LITRE TRAILED SILVAN FIRE FIGHTING
UNITS
Reliable Selecta Power or Davey Self-priming fire fighter pumps
Powder coated trailer including 50mm tow hitch & jockey wheel
UV stabilized poly tuff tank
Mudguards standard on all models
Heavy duty suspension tyres
Quick fill kit uses pump and large 6m hose for rapid tank fill (1000L model)
Factory fitted options:
ADR approved LED tail lights
(standard on Davey models)
ADR approved break system
(standard on Davey models)
Twin impeller Davey pump
(option for 800L model)
Diesel Engine (Yanmar or
Subaru option for 1000L
model)
Electric start
Visit our website: www.fsme.com.au
Page 48
FLAME GUN
SHEEN FLAME GUN
The ultimate way to eradicate unwanted and noxious weeds
along with other parasites without using potentially dangerous
chemicals.
The principle of the X300 Flame Gun is that of a pressure
stove or blow torch. Fuel is contained in an air tight tank and
is forced into the burner via a control valve by air pressure
supplied by the built in pump. The fuel (household kerosene)
is preheated and vaporized for passing through a helically wound coil.
With a core temperature of 1090°C it destroys top growth weeds, seeds and harmful bacteria
thereby sterilising the soil and leaving a potash rich residue for future plantings.
It is used for sterilising seed beds prior to planting, and for ground clearing under trees and
fences, and is great for inter-row weeding. A separate trolley and hood is also available as
an option.
It can also be used around the home to kill weeds that pop up between pavers and concrete.
Other uses for the Flame Gun are killing off lice and mites in chook sheds and also destroying
rotting fruit on the ground to reduce fungal and potentially harmful spore germination.
Frequently asked Questions:
1.
How soon can I get my results?
When using the flame gun for the first time, never attempt to consume all the weed
in one burning. The two-stage method is recommended.
Stage 1: A 1090°C controlled flame kills weeds. When directed at the base of
weeds it stops sap rising, so the top growth dries out in a day or two.
Stage 2: Dry weeds will ignite immediately when the flame comes into contact,
clearing the ground of vegetations, seeds, pests etc.
2.
Can I clear bush?
For the clearance of bushes, tangled vines, hedges etc, it is recommended to cut the
growth as near to the ground as possible. Allow it to stand and dry out for at least
24 hours. One burning will then consume the cut bush and kill the roots and seeds at
the same time.
3.
Can I start a bush fire?
As the flame gun is operated at 1090°C the weeds that are
in contact with the flame burn instantly and therefore there
is nothing left to continue combusting.
The Flame Gun weighs only 7.5kg when fully filled with Kerosene,
Its ergonomic design makes it easy to carry and operate.
DELIVERY ANYWHERE IN AUSTRALIA
Page 49
GRADER BLADES
BERENDS STANDARD & MEDIUM DUTY RANGE
Grader blades designed and developed over many years to provide the user with a most
versatile implement at a reasonable cost.
Fitted with positive quick release centre for angle selection, to minimise wear & tear.
Allows 24 different angle positions. Blade can be reversed for back filling.
Can be offset in seconds to work outside the tractor wheel to the left or right hand
side (except for fixed models). Choice of 5 positions each way to a maximum of
600mm offset.
Alternative holes for the lower linkage arms (except 6’ fixed model), provide ample
tilt for V-draining.
6’ Medium Duty model (0007) available with ratchet tilt or hydraulic option.
Provides 30° tilt each way.
Heavy Duty reversible cutting edges for maximum life.
Optional pneumatic wheel kit available for depth
control.
0006
6’ MD inc RIPPERS
PICTURED
MADE IN AUSTRALIA
MODEL
0002
4”
STD
0016
5’
STD
0008
6’ STD
FIXED
0003
6’ STD
OFFSET
0005
6’ MD
OFFSET
0006
6’ MD inc
RIPPERS
0007
6’ MD inc
RATCHET
TILT
4’
5’
6’
6’6’
6’
6’
6’
MOULDBOARD
THICKNESS
6mm
6mm
6mm
6mm
8mm
8mm
8mm
MOULDBOARD
HEIGHT
350mm
350mm
350mm
350mm
450mm
450mm
450mm
TRACTOR HP REQ
16-35
16-35
20-30
20-50
30-60
30-60
30-60
OFFSET POSITIONS
0
0
0
9
9
9
9
101kg
115kg
160kg
180kg
200kg
260kg
206kg
CUTTING WIDTH
NETT WEIGHT
Visit our website: www.fsme.com.au
Page 50
GRADER BLADES
BERENDS HEAVY DUTY RANGE
“When extra strength is needed”
The HD model was added to the range when the EHD model was upgraded to similar to the
Hydraulic blade specifications, making the gap between the MD and the EHD too large. It is
a simplified version of the old EH, with the tilt function being moved from under the
turntable to the linkage pins similar to the MD range.
Fitted with high tensile 50mm main pivot (adjustable for wear), high tensile turntable,
and pivot pins 40-50mm wide to minimise wear and avoid breakages.
24 angle positions with adjustment from the tractor seat.
Offsets 4 positions to both right and left allowing blade to work outside the wheel
even at an angle.
Blade rotates 360° for forwards and backwards
operation.
Curved 10mm thick mouldboard for strong cuts
at the correct angle, and high clearance for greater
capacity. Hardened, reversible cutting edges (as
used on road graders).
12 month Warranty against faulty materials or
workmanship.
MODEL
00035
6’
0036
7’
0037
8’
6’
7’
8’
MOULDBOARD THICKNESS
10mm
10mm
10mm
MOULDBOARD HEIGHT
500mm
500mm
500mm
TRACTOR HP REQ
40-100
40-100
40-100
CAT 1/2
CAT 1/2
CAT 1/2
OFFSET POSITIONS
8
8
8
ANGLE POSITIONS
24
24
24
305kg
350kg
370kg
CUTTING WIDTH
CATEGORY - 3 POINT LINKAGE
NETT WEIGHT
DELIVERY ANYWHERE IN AUSTRALIA
Page 51
GRADER BLADES
BERENDS EXTRA HEAVY DUTY RANGE
“With over 35 years of manufacturing, this is the strongest mechanical
grader blade Berends have ever produced. You cannot buy better value”
The EH is basically a manual version of the Hydraulic blade, built to cope with the higher
horsepower tractors which are more common today.
Designed to ensure all moving parts are kept tight - vital, as anything loose will
eventually wear and break.
Fitted with high tensile 66mm main pivot. Main and tilt pivots sleeved and greaseable
for ease of operation, strength and reduced wear. Sleeved offset pivot points for extra
strength. Extensive use of high tensile steels for extra strength in high stress areas.
Easy to adjust tilt function standard. Tilt below turntable allows tilting angle to remain
constant even when fully offset and ensures no decrease in tilting angle if the blade is
offset. Replaceable bronze bushes on tilt adjustment.
Optional hydraulic tilt function makes for even easier operation from the tractor seat.
24 angle positions with adjustment from the tractor seat.
Offset 4 positions to both right and left allowing blade to work outside the wheel track
even at an angle.
Blade rotates 360° for forwards and backwards operation
Curved 10mm mouldboard, reinforced with heavily gusseted corners for strength
where it counts and higher clearance. Hardened, reversible cutting edge.
Almost half a tonne of weight ensures more strength and better penetration into hard
surfaces.
MODEL
0039
7’
0040
8’
7’
8’
MOULDBOARD THICKNESS
10mm
10mm
MOULDBOARD HEIGHT
500mm
500mm
TRACTOR HP REQ
60-120
60-120
CATEGORY - 3 POINT LINKAGE
CAT 2
CAT 2
OFFSET POSITIONS
8
8
ANGLE POSITIONS
24
24
410kg
425kg
CUTTING WIDTH
NETT WEIGHT
Visit our website: www.fsme.com.au
Page 52
GRADER BLADES
BERENDS
“The ultimate in grader blades - alter tilt, angle & offset from your tractor
seat on the move”
Features the exclusive patented swivel assembly, which supersedes the pivot pin
assembly resulting in superior strength & reliability.
Angle up to 45° both ways.
Offset up to 600mm left or right.
Tilt in excess of 30° left or right.
Tilt and angle are hydraulically operated. Offset can be manually adjusted (2 ram
model) or hydraulically adjusted (3 ram model).
Blade rotates 360° for forwards and backwards operation.
Curved 10mm mouldboard, reinforced with heavily gusseted corners for strength
where it counts and higher clearance.
Hardened reversible cutting edge.
Over half a tonne of weight ensures superior strength and penetration into hard
surfaces.
Optional depth wheel 14” pneumatic tyred wheel with
either manual ratchet link or
hydraulic adjustment.
Diverter kits are available to reduce
the amount of hydraulic outlets
required from the tractor.
MODEL
0013
8’
3 rams
00014
8’
2 rams
0017
10’
3 rams
0028
10’
2 rams
8’
8’
10’
10’
MOULDBOARD HEIGHT
500mm
500mm
500mm
500mm
CATEGORY - 3 POINT LINKAGE
CAT 2
CAT 2
CAT 2
CAT 2
NETT WEIGHT
520kg
520kg
550kg
550kg
CUTTING WIDTH
DELIVERY ANYWHERE IN AUSTRALIA
Page 53
GRADER BLADES
FARM-AID GRADER BLADE ATTACHMENTS
Custom fitted to grader blades.
FA900 - Rippers to suit 4’ Grader Blades
FA901 - Rippers to suit 5’ Grader Blades
FA902 - Rippers to suit 6’ Grader Blades
SILVAN
Ideal for small acreage properties. Very handy for use in garden beds, forming small tracks,
scraping mulch and forming fire breaks.
Features include:
All welded steel construction
6mm channel reinforced mouldboard
Premium enamel top coat paint
Reversible heat treated steel cutting edge - Standard Duty model
Reinforced mouldboard with heavy steel edge - Light Duty model
Category 1 3PL attachment
Tilt positions - Standard Duty model
360° lead angle each side - Light Duty
model
CODE
CUTTING WIDTH
WEIGHT
TRACTOR HP REQ
139WGB4
LIGHT DUTY
140WGB5
STD DUTY
140WGB6
STD DUTY
4’
5’
6’
74kg
123kg
133kg
10-20HP
20-30HP
20-30HP
Visit our website: www.fsme.com.au
Page 54
GRADER BLADES
JARRETT
Features (all models):
Robust construction
Deep, curved face
Reversible cutting edge
Easy side tilt adjustment
Full rotation for push & pull operations
Options:
Scarified assembly for breaking the “crust” (GM & GH only)
Depth control wheel
MODEL WIDTH BLADE
SPINDLE
DIA
NO.
LINKAGE
MIN
WEIGHT
ANGLE
POWER
ADJ
GM180
1.8m
380mm
50mm
10
CAT 1
20HP
160kg
GM210
2.1m
380mm
50mm
10
CAT 1
40HP
190kg
GH210
2.1m
380mm
70mm
14
CAT 1/2
40HP
220kg
GH240
2.4m
380mm
70mm
14
CAT 1/2
50HP
250kg
GEH240
2.4m
530mm
100mm
12
CAT 2
60HP
480kg
KANGA 1200 4’ MINI (45000)
Headstock Material
Mouldboard
Cutting Edge
Finish
Linkage / Mounting
Offset
Tilt
Angle
Tractor HP required
Welded, reinforced 80x80x4mm RHS
Pressed 6mm mouldboard with channel reinforcing & 10mm turn
table
150mm head hardened carbon/chrome (spring steel) reversible
Powder coated baked enamel
Double clevis Cat 1 - supplied with
Cat 1 pins & clips
3 positions left & right
Using lower linkage pin holes &
tractor arms
28 positions over 360°
18-30
DELIVERY ANYWHERE IN AUSTRALIA
Page 55
GRADER BLADES
KANGA 1800 6’ S RANGE (44000)
Headstock Material
Mouldboard
Cutting Edge
Finish
Linkage / Mounting
Offset
Tilt
Angle
Tractor HP required
Welded, reinforced 100x100x4mm RHS
Pressed 6mm mouldboard with channel reinforcing & 12mm turn
table
150mm head hardened carbon/chrome (spring steel) reversible
Powder coated baked enamel
Cat 1 & 2 top. Cat 1 lower. Both double clevis and
supplied with Cat 1 pins and clips
3 positions left & right
Using lower linkage pin holes &
tractor arms
28 positions over 360°
18-35
KANGA 1800 6’ M RANGE (43000)
Headstock Material
Mouldboard
Cutting Edge
Finish
Linkage / Mounting
Offset
Tilt
Angle
Tractor HP required
Welded, reinforced 100x100x6mm RHS
Pressed 6mm mouldboard with channel reinforcing & 16mm turn
table
150mm head hardened carbon/chrome (spring steel) reversible
Powder coated baked enamel
Cat 1 & 2 top. Cat 1 lower. Both double clevis & supplied with
Cat 1 pins and clips
5 positions left & right
Using lower linkage pin
holes & tractor arms
28 positions over 360°
30-50
Spares Available for
most Grader Blades
Visit our website: www.fsme.com.au
Page 56
GRADER BLADES
KANGA MULTI CLAMP RANGE (41000 - 6’ / 4000 - 8’)
Headstock Material
Fully welded & reinforced pipe & RHS construction
Mouldboard
Pressed 8mm mouldboard with channel reinforcing
Cutting Edge
150mm head hardened carbon/chrome (spring steel) reversible
Finish
High build oxide primer with high quality equipment enamel top
coat
Linkage / Mounting
Double clevis Cat 1 & 2 linkage with Cat1 pins and clips.
Offset
0-45° in 5° increments left or right
Tilt & Angle
0-45° in 5° increments left or right
Tractor HP required
35-60 (6’) 40-70 (8’)
KANGA H RANGE (available in 6’ & 8’)
Headstock Material
Fully welded & reinforced 150x150x5mm
RHS
Movement Via
75mm (3”) hydraulic rams complete with hoses
& fittings or manual adjustment
Mouldboard
8mm reinforced & gusseted with 16mm turn tables
Cutting Edge
150mm head hardened carbon/chrome (spring steel) reversible
Finish
High build oxide primer with high quality
equipment enamel top coat
Linkage / Mounting
Double clevis Cat 2 lower linkage with pins &
clips.
Offset
Variable - up to 20° left or right
Tilt & Angle
Variable - up to 30° left or right
Tractor HP required
50 - 90
KANGA XH RANGE (available in 8’ & 10’)
Headstock Material
Fully welded & reinforced 150x150x5mm RHS
Movement Via
100mm (4”) hydraulic rams complete with hoses & fittings
Mouldboard
10mm reinforced & gusseted with 20mm turn tables
Cutting Edge 150mm head hardened carbon/
chrome (spring steel) reversible
Finish
High build oxide primer with high quality
equipment enamel top coat
Linkage / Mounting
Double clevis Cat 2 lower linkage with pins & clips.
Offset
Variable - up to 20° left or right
Tilt & Angle
Variable - up to 30° left or right
Tractor HP required
90 - 130
DELIVERY ANYWHERE IN AUSTRALIA
Page 57
GRAIN & WOOL HANDLING EQUIPMENT
GRAIN MILL - PORTABLE 24v
With your own grain mill you can source whole grains as you desire for
your own mix, or mill home grown grain into flour. Hopper capacity is
13 litres (approx 15kg).
Grain must be milled for the animal to extract the nutrition from it.
This mill is powered by a 750W 240V electric motor which ensures fast
and consistent milling. The mill is supplied with four screens, grinding
to sizes - 2.5mm, 4mm, 6mm and 8mm.
The machine is completely dustless, as the large 13 litre container
(supplied) fits neatly onto the mill outlet.
Accidental access to moving parts is prevented by automatic shutdown
of the motor if the access door is opened, or the grinding chamber is not
securely closed.
GRAIN SCOOPS
Polished Aluminium scoops
The round bottom generally makes it easier to penetrate
feeds & grains.
Available in 1 litre, 1.6 litre & 2.4 litre capacities
Stand Up scoops
The hard-corner flat rim scoops cleanly off the bottom of bins or
containers reducing waste/residue. Water-level volume, and will
stand like a jug when full.
Available in 1litre & 2 litre capacities
CHAFF / GRAIN BINS
Holds 1¼ bags of chaff
Hinged lid - easy access, yet secure storage
Rust free poly construction
Available in standard green or in the popular colour
range - red, purple, blue, pink or yellow
Space saving modular design
Visit our website: www.fsme.com.au
Page 58
GRAIN & WOOL HANDLING EQUIPMENT
GRAIN SHOVELS
Smooth lightweight poly
One piece moulding – no separate parts
Almost unbreakable
Available in green, red, blue, yellow & white
BAG & BALE HOOKS
Bag Hook
Cargo Hook
Wool Bale Hook
PACKING BAG NEEDLES
Stainless Steel needles useful for sewing up all manner of bags, canvas & leather.
Large eye takes string with ease.
Cutting-type point makes adequate hole to pull through.
Sizes available: 100mm - 250mm
HARDWARE
KNIVES & SCYTHES
A large range of styles and sizes available.
FERN HOOK
HAND SICKLE
CANE KNIFE
MACHETE
DELIVERY ANYWHERE IN AUSTRALIA
Page 59
HARDWARE
SHERLOCK WHEELBARROWS
“ A tradies best friend”
Heavy duty powder coated steel,
galvanised or poly tray
72 - 100 litre capacities
Heavy duty hardwood or galvanised
steel handles
Fully welded solid steel legs & front stays
Heavy duty 18mm poly base board
Pneumatic wheel on steel rim
How ‘bout getting the little
tacker a Sherlock Kids
Wheelbarrow to help out.....
CYCLONE HARDWARE AVAILABLE
Shovels & Spades
Earth augers
Post Hole cleaners
Crow bars
Fencing bars
Picks
Hoes
Cultivators
Rakes
Forks
Lawn Edgers
Blocksplitters & Axes
Pruning instruments
Woven Weed Control Mat & Mulch Mat
Lawn Rollers
Visit our website: www.fsme.com.au
Page 60
HARROWS (PASTURE)
BERENDS
The Berends Pasture Harrows are ideal for renovating
pasture, landscaping horse arenas, race tracks or sports
fields and for spreading seed and fertiliser into the soil.
It consists of three rows of 12mm round scarifier tines
which break up manure, loosens hard surfaces and
increases aeration which in turn will stimulate new
growth. Behind this are mounted four rows of 12mm
square smudger bars which help to spread the manure
and level the ground. This flexible design allows the
harrows to follow ground contours without tangling up
and aid in keeping them relatively clean of trash.
Trailing weights are mounted on the back to keep the
harrow on the ground when travelling.
Available in 4’ to 12’ - with or without a lifting frame
MURRAY & SON
SERIES 20 PASTURE HARROW
A natural choice in pasture harrows. Strong, durable, generally
suited to areas larger than 40 to 60 hectares (100 to 150 acres) or anywhere pasture needs an
extra tickle up or working by a pasture harrow.
The Series 20 features 3, 4 or 5 rank tine sections. Standard (2’6”) or Super (5’) depth or rear
Mesh Chain can be specified. Available in drag type or hoist lift type.
Sizes Available:
3 sections - 2.59m (8’6”)
4 sections - 3.45m (11’4”)
5 sections - 4.31m (14’2”)
6 sections - 5.18m (17’)
Genuine replacement
harrow points in stock.
DELIVERY ANYWHERE IN AUSTRALIA
Page 61
HARROWS (PASTURE)
SERIES 05 PASTURELAND HARROW
Ideal for pastures which are in good or reasonable condition.
This light duty Pastureland Harrow is suitable for pasture areas of less than 40 to 60 hectares
(100 to 150 acres) in total. A simple and versatile means of pasture improvement.
Choose from Standard (2’6”) or Super (5’) depth or rear Mesh Chain can be specified.
Available in drag type or hoist lift type.
Sizes Available:
1.52m (5’)
1.83m (6’)
2.44m (8’)
3.04m (10’)
3.65m (12’)
4.57m (15’)
6.09m (20’)
SERIES 09 CHAIN HARROW
A multi-purpose “reduced tillage” harrow system which may be used for spreading organic
matter and leveling seedbeds. Beneficial in strip grazed pasture situations and a useful
adjunct to efficient harvesting of clover seed by vacuum harvesters.
Three depths of chain mesh sections available, 0.76m (2’6”), 1.5m (5’) and 2.28m (7’6”),
each providing a different level of aggression and pulverization to suit individual
requirements.
Sizes Available:
1.52m (5’)
2.44m (8’)
3.04m (10’)
3.65m (12’)
4.57m (15’)
6.09m (20’)
Visit our website: www.fsme.com.au
Page 62
HARROWS (CULTIVATION)
MURRAY & SON
SERIES 08 & 44 STUMP JUMP HARROWS
A dependable and versatile style of harrow popular
when cultivation type harrowing needs to be done.
Rugged constructions and flexible stump jump action
make these harrows a natural choice in assisting to
prepare cultivated land. The sections easily
accommodate uneven ground, stony areas or roughly
cleared country which would present difficulties for
rigid tine harrows.
Manufactured in 20 tine sections with a weight of 41kg for the Series 08 and 44.2kg for the
Series 44.
All sections cover 863mm (2’10”) and feature 44mm (1 ¼”) tine spacing.
A four point pull design is featured on the Series 08 whilst the Series 44 sections have a two
point pull design.
SERIES 04 DIAMOND HARROWS
For weed control and final seedbed preparation.
This rigid Diamond Harrow features a sturdy
square section, low draft, tapered tines to shatter
soil crusts allowing improved aeration and
moisture penetration.
Built in 1.016m (3’4”) wide sections weighing
30kg each and supplied in sets between two and
ten sections complete with drawbars.
SERIES 48 JUMBO CULTIVATION HARROWS
The Series 48 Jumbo Cultivation Harrow meets a
real need that has emerged in some areas for a
flexible, cultivation-style harrow suitable for
seedbed preparation and soil working in heavier
soils.
It is significantly heavier than standard Stump
Jump Harrows. Heavier steel components add to
weight for improved penetration, greater strength
and an extended working life.
Greater tine layback and wide inter-rank tine spacing give the harrow a
superior trash handling ability. Longer tines allow a greater working depth
and provide a longer working life. Hitch points and pivot pins have been engineered to
accommodate the rigours of the heavy work the implement is designed for.
DELIVERY ANYWHERE IN AUSTRALIA
Page 63
HARROWS (LEVELLING)
MURRAY & SON
SERIES 03 & 35 LEVELLING HARROWS
A finishing tool to complement almost any
sowing or cultivation implement.
Available in 3, 4 or 5 rank deep models in
either “light” or “heavy” weights.
Three rank versions with 9 or 12 tines are for
use in light to medium soils in conjunction with traditional combines and seed drills.
Five rank models of 15 or 20 tines are for use in heavier soils and complement cultivators,
scarifiers and chisel ploughs.
Three and four width versions allow extensions of working width in increments of 235mm
(9 ¼”) to suit primary machines of almost any width.
SERIES 06 SPRING TINE HARROWS
Heavy duty 3 rank design for tough conditions.
Complements scarifiers and chisel ploughs for breaking down cloddy ground and final
seedbed preparation.
Available in “kinked” or “straight” tine models.
Sizes Available:
1.37m (4’6”)
1.83m (6’)
2.28m (7’6”)
DELIVERY ANYWHERE IN AUSTRALIA
Page 64
HEADSTOCKS
FARM-AID
3PT LINKAGE A-FRAME
The ideal solution to towing a standard trailer with your
tractor.
Available with our without a tow ball.
LIGHT DUTY HEADSTOCK (FA309)
90 x 10mm flat bar
Complete with wedges & bottom linkage pins
HEAVY DUTY HEADSTOCK (FA308)
100 x 16mm flat bar
Complete with wedges & bottom linkage pins
HILLERS, FURROWERS & BED MAKER ASSYS
BERENDS MERBEIN PLOUGH
Merbein Ploughs consist of a toolbar made from two sections of 100 x 50 x 6 RHS with a 1”
gap between them. They are available in 6’, 7’ and 8’ lengths. The individual disc units
come in either two or 3 disc model with either one or two mounted on each toolbar. The disc
units are assembled either as a left hand or right hand unit. This is determined by which way
the soil is thrown.
The discs are 22” x 5mm, with a scalloped and a plain disc on the two disc unit and a two
scalloped and one plain on the three disc unit. Each disc is mounted to a Merbein bearing
assembly which consists of a sealed shaft with two heavy duty greaseable bearings. The dust
cap which is standard on these assemblies is quite light and we highly recommend upgrading
to the heavier 10mm dust cap in abrasive conditions.
Merbein ploughs are quite capable of ploughing up to a
10” depth or more.
If only one unit (side) is mounted on a toolbar it may be
necessary to fit a rear coulter. This keeps the unit straight
and stops the plough dragging the tractor to one side.
Visit our website: www.fsme.com.au
Page 65
HILLERS, FURROWERS & BED MAKER ASSYS
FARM-AID DISC HILLERS
FA800 - 13” with 1 ¼” Round Shank - Bare
FA801 - 13” with 1 ¼” Round Shank - including
Clamp & Wedge
FA802 - 20” with 2” Round Shank - including
Clamp & Wedge
FA807 - 22” with 2” Round Shank - including
Clamp & Wedge
FARM-AID TOOLBAR
FA311 - 2” Toolbar Mid Tensile Bar (per metre as ordered)
FARM-AID FURROWERS
FR9312 - 12” Bare
FR9315 - 15” Bare
FA700 - 20” Bare
FARM-AID BED MAKER ASSYS
FA803 - 6’ Toolbar, Light Duty Headstock, 2 x 13” Disc Hillers including Clamps & Wedges
FA804 - 6’ Toolbar, Heavy Duty Headstock, 2 x 20” Disc Hillers including Clamps & Wedges
Please refer to the Toolbar Tiller Components on Page 131 for additional parts available.
DELIVERY ANYWHERE IN AUSTRALIA
Page 66
LANDSCAPE RAKES
BERENDS
One of the only Australian made LANDSCAPE RAKES on the market. This machine is ideal
for raking light material, harrowing pastures and for final soil surface preparation - whether it
be on the driveway, the garden or even the horse arena.
Features:
Three different pitch settings control the aggressiveness, including one float position
which allows the tine to hinge backwards on the frame. This would be used when
operating around rocks or stumps and enables the tines to lift over those obstacles.
There is enough weight in the frame to keep the tines on the ground under normal
raking conditions.
Heavy tubular construction and heavy tines makes the imported ones look lightweight.
Category 1 linkage.
Double bolt mounting system.
Fitted with 32 x 10mm hardened tines spaced at 65mm centres.
Sizes Available:
1.2m (4’)
1.5m (5’)
1.8m (6’)
2.1m (7’)
Please also refer to Stick Rakes section on Page 130
Replacement tines available for Brand Name Stick Rakes
Please contact the FSME SalesTeam
Visit our website: www.fsme.com.au
Page 67
LAWN ROLLERS
FARM-AID
Ideal for general farm use or specifically for turf farms, race clubs, ovals etc
75 x 50 x 6mm RHS main frame
Heavy duty linkage
Round, seamless tubes, 14” diameter x ¼”
wall thickness
Can be filled with water for additional weight
Trailed models made to order
CODE
SIZE
WEIGHT
EMPTY
(kg)
WEIGHT
FILLED
(kg)
FA447
3’
90
250
FA448
4’
120
340
FA449
5’
150
420
FA450
6’
180
500
FA451
7’
210
560
FA452
8’
240
670
FA453
9’
270
750
FA454
10’
330
840
SILVAN
Maintain a smooth and level lawn with total and complete ease
Water filled plastic garden rollers
Light and easy to handle
UV treated barrel
Galvanised tube handles with steel bearings to ensure a long
life
DELIVERY ANYWHERE IN AUSTRALIA
Page 68
MADE IN AUSTRALIA
LIFTING JIBS & LINKAGE SCOOPS
BERENDS
STANDARD LIFTING JIB (0140)
The Standard Model is a Cat 1 model with bushes to fit Cat 2. It is made from 100 x 50 x
6mm RHS and has two lifting points. The closer one being used for heavier loads,
approximately 750kg, and the one on the end for lifting around 500kg. Obviously, the end
point has a slightly higher lift of around 10’ (3m). It is critical that lifting jibs are lifting
straight and not from a sideways motion and that the tractor has the appropriate lifting
capacity. The overall length is 2.2m.
HEAVY DUTY LIFTING JIB (0142)
The Heavy Duty Model is a Cat 1 model with bushes to fit Cat 2. It is made from 100 x 100
x 6mm RHS and has two lifting points. The closer one being used for heavier loads,
approximately 1,000kg, and the one on the end for lifting around 750kg. Obviously, the end
point also has a slightly higher lift of around 12’ (3.6m). The heavy Duty Model has an
adjustable A frame to suit different tractors and provides different degrees of arc when lifting.
The overall length is 2.2m.
FARM-AID
FA1011 - Standard Lifting Jib
FA1012 - Heavy Duty Lifting Jib
BERENDS LINKAGE SCOOP (0033)
The Linkage Scoop has a bucket which is 760 x 610 x 460mm and holds approximately
0.3m³. It can only be operated backwards and has a lifting height of 600mm. The scoop is
ideal for moving materials about, and has a range of top link mounting points to vary the
angle of attack on the bucket. The trip can be operated from the tractor seat via the lever or
rope. The Linkage Scoop is ideal in situations such as carrying gravel from a pile to fill in
holes in a track.
Suggested tractor Horsepower is 18 - 70HP.
Weight approximately 80kg.
FARM-AID
FA400 - ½ yard capacity 1180 x 610 x 460mm (100kg)
Visit our website: www.fsme.com.au
Page 69
LIVESTOCK HANDLING EQUIPMENT
BERENDS CATTLE CRUSH (0167)
The BERENDS VET CATTLE CRUSH has a walk
through bailgate, meaning the animal’s head is trapped
by the gate and as it is opened, the animal walks out.
The bailgate consists of two panel doors which slide
together. These doors are operated by a lever at the rear
of the crush, making it easy to get the animal to go
through to the gate. To release the animal, the locking
ratchet is released and the lever lifted.
The crush is very fast to use.
Features:
Double ratchet for fine incremental adjustment
Nylon rollers for smooth and easy operation
Lugs to hold restraining bar
Right hand “split” gates hinge at front to enable gates to squeeze in on smaller cattle
Bolt down mounting plates
Rear Vet gates both upper and lower on left hand side plus full gate on right hand side
Bailgate operated from “fold away” rear handle
Spring operated zinc plated catches
Left hand “split” side gates hinge at rear for drafting animals out
Zincalume panels primed and enamel painted
Other Brand Name Crushes also available
CALF FEEDERS
EASY & SPEEDY FEEDERS
EASY FEEDER is a single-speed nursing bottle whilst the
SPEEDY FEEDER has three speeds
Multi-directional easy-grip hand hold
Teat mounted low in cap to ensure bottle can be completely emptied
Wide 70mm diameter neck ensures easy filling and cleaning
Wide base gives the bottle maximum stability when standing
OUR MOTTO IS QUALITY AND SERVICE
DELIVERY ANYWHERE IN AUSTRALIA
Page 70
LIVESTOCK HANDLING EQUIPMENT
RAIL BUCKET 6-PLACE
20 Litre, 6 - place CALFETERIA type feeder
Hang on any convenient rail up to 32mm thick
Includes fast flow teats complete with intake
elbow/valves
Soft cover available separately
MILK TRAIN
Modular calf feeding bucket
Used as a 2 - place feeder, or dove - tailed
together to make 4, 6 or 8 place feeders
Includes new adjustable latch-strap
system
10 litre capacity per 2 - place feeder
Includes teats complete with intake
elbow/valves
CALF / COW LIFTING EQUIPMENT
CALF SLING
Useful for many calf handling tasks
Hand guide - and - control device when moving a
young calf on its feet instead of carrying it
Quick and comfortable sling for weighing
DAISY LIFTER
Designed for medium term support for a down cow
Cow supported over a large body area thus
reducing pressure points
Fully adjustable to fit any size animal
Supplied as a kit in a handy carry bag
Available in Standard & X - Large Models
Maximum lift load is 1000kg
Visit our website: www.fsme.com.au
Page 71
LIVESTOCK HANDLING EQUIPMENT
DAIRY & BEEF PRODDERS
DURAPROD
Battery powered - 4 x “C” batteries required
Easy change battery pack
34 - 130cm shafts available
Patented circuit design that has as near to possible elimination of the user receiving
accidental shocks, even when working in wet/difficult conditions
GROOMING & SHOW
CLIPPERS - HEINIGER ELECTRIC CLIPPERS
Swiss company HEINIGER have developed a range of high quality, reasonably priced,
electric clippers.
All Heiniger clippers feature unbreakable and
lightweight glass - fibre - filled polyamide motor
housings
Power cables are 5 metres long, with a flexible
protective sleeve to prevent damage at the clipper
entry point
Patented adjustable blade tension system
Supplied in protective carry case, clipper screw
driver, lubricating oil & cleaning brush
For a comprehensive listing of all models of clippers available, please contact a member of
the FSME Sales Team
BLOW DRYER
Purpose built livestock grooming machine
All steel construction
Heavy duty ball-bearing variable-speed 2HP - 240 volt motor
Suitable for operation in vertical or horizontal position
Air volume speed 35cfm - 100cfm
Supplied complete with 6’ of crush resistant hose, nozzles &
special coat rake tool
DELIVERY ANYWHERE IN AUSTRALIA
Page 72
LIVESTOCK HANDLING EQUIPMENT
PIG NIPPLES
PIGLET MONOFLO
Machined in one piece with hexagon nut for easy servicing.
Light action for piglets.
Standard 15mm (½” BSP) fitting.
Suit 15 to 50psi.
Fine mesh domed filter for best
service.
Adjustable flow rate
FATTENER MONOFLO
Machined in one piece with hexagon nut for easy servicing.
Ideal for fatteners or sows.
Suit pressures from 15 to 50psi.
Fine mesh domed filter for best service.
Adjustable flow rate.
POULTRY FEEDERS
Simple all galvanised construction.
Ideal for rugged backyard and small block conditions.
Made in Australia.
POULTRY LEG BANDS
Easy identification of poultry and other larger birds for age, breeding etc.
Spiral plastic bands with 9 - 20mm ID.
Available in blue, orange, red & white.
Packs of 10 or 100.
Visit our website: www.fsme.com.au
Page 73
LIVESTOCK HANDLING EQUIPMENT
WATER & FEED BINS
NYLON FARMHAND WATER BOWL
Fully resistant to corrosion in any water
Plastic bowl livestock-friendly
Hinged stainless steel lid for easy access to float assembly
Drain incorporated
4 litre capacity
STAINLESS FARMHAND WATER BOWL
Stainless steel manufacture with hinged lid assembly
Slopes to front bottom to bring debris forward for easy cleaning
Post-mount backstrap supplied
No drain incorporated
2.5 litre capacity
TROUGHTOMATIC WATER FILLER
Clips over any handy bowl, container or trough
Standard water tap quick - fit hose coupling
Water fills up in the container to shut off the float valve
2 water level settings by adjusting brackets depth
RAPID PLAS FENCE DRINKER OR FEEDER
45 litre 1 piece moulded drinker inc float & cover
½” high pressure float valve for reliable service
Galvanised steel mounting brackets
2” drain bung for easy cleaning
Available in either feed or water model
PRO TUB TROUGHS
Float enclosure moulded as part of the trough
Raised float allows trough to fill completely
All pipework protected by trough surround
2” drain bung for easy cleaning
Fitted with 1” high pressure, high flow valve
DELIVERY ANYWHERE IN AUSTRALIA
Page 74
LIVESTOCK HANDLING EQUIPMENT
LONGLINE WATER TROUGHS & FEEDERS
Well proven over many years
Huge range of sizes to suit every need
Available in either feed or water model
COMBINATION TANK & TROUGH
The quick and easy solution for stock water management on your
property!
Cooler, cleaner water with long - term security for all
mobs!
Zero installation needed between tank & trough
Guaranteed proven design to withstand sheep and cattle
Internal plumbing prevents stock damage
Supply of water is kept considerably cooler compared to
troughs with no reservoir
Algae inhibitor
Designed for easy cleaning with sweep out ramps
For a complete listing of available models, please contact a member of the FSME Sales
Team.
LOG SPLITTERS
TW-P1
The hallmark model for home & farm use. Comes
standard with log cradles & reliable Honda OHV GX
Series Engine.
Shown with optional 4 - way wedge & table grate.
TW-HV2
Power and speed combined in a versatile design.
Operate it horizontally or vertically and take advantage
of the 25 tonnes of splitting force, larger engine and
pump with an 18 second cycle time.
For a complete listing of available models, please contact a member of the FSME Sales
Team.
Visit our website: www.fsme.com.au
Page 75
MATERIAL HANDLING EQUIPMENT
FORKLIFT ATTACHMENTS FOR EVERY JOB
....VERSATILITY....PRODUCTIVITY....FLEXIBLITY
PREMIER ENGINEERING (QLD) PTY LTD
ABN 45 056 536 353
Repetition and General Engineering
Guillotine and Pressbrake Facilities
Materials Handling Equipment Manufacturers
We are an Engineering Company with full workshop facilities and
can manufacture and repair Farm Equipment to suit all your needs.
Let our machines and qualified staff take care of the job for you.
DELIVERY ANYWHERE IN AUSTRALIA
Page 76
MILKING MACHINES
MILKWELL PORTABLE MILKING
MACHINES
Milkwell ® have been supplying quality dairy
equipment to the farming community for over
75 years.
Product Information:
The Milkwell ® Portable Bucket Milking
Machine is powered by a 0.75HP 240v
electric motor, fully sealed for safety and
durability to the dry type vacuum pump.
The unit has a galvanised vacuum tank with
an 18 litre capacity, ensuring virtually no chance of milk over-flow finding its way into
the pump.
With a removable rubber viewing lid, the tank is very easy to clean.
A 40 litre stainless steel milk tank ensures sufficient capacity for 2 - 3 cows.
The unit comes complete with all rubber-ware and milking cluster is supported by a
“swinging arm” which makes it easy to access animals in a race or bale.
The teat-cups have clever milk sights, so one can easily see when the milk is flowing.
The whole unit mounts on a robust galvanised steel frame with large rubber wheels for
extremely easy maneuverability.
Applications:
Whether you have a small or larger scale dairy farm looking for a convenient means of
milking independent from the main dairy (eg in the case of mastitis), the Milkwell machine
will prove extremely useful.
These machines are ideal for small farmers and small boutique dairy operations, where they
are using their own sheep, goat or cow milk for household or boutique dairy manufacturing.
For stud breeders who travel and show their livestock, finding suitable milking facilities is
often difficult. The Milkwell Portable machine overcomes this problem, as it is small
enough to be transported and can be used anywhere there is 240v mains power, or if not, a
basic house-hold generator.
Available in Cow, Goat & Sheep models.
Visit our website: www.fsme.com.au
Page 77
MULCHERS
BERENDS
Mulching mowers (or flail mowers) are simply wonderful machines and Berends reckon that
their models are among the best.
A slasher can be driven through a clump of blackberries and rushes and cut them off, leaving
great piles of dead material preventing animals getting in and smothering re-growth or…..
You can turn it into mulch, fertilising the ground and actually getting pasture to grow. You
can mulch hay paddocks to set them back to cut hay at a better time, and get the benefit of
increased hay quantity combined with better re-growth as the mulch holds moisture.
Mulchers will also mulch up many things which used to have to be picked up - prunings in
orchards being the most common, but also bark and sticks under trees in addition to pasture
mat which can be cut up.
Combining mulching with seed or seed and super can result in a tremendous increase without
putting the paddock out of production for long.
LOW BODY MODEL
Versatile heavy duty mulching mowers designed and manufactured for clean, fast mowing
and mulching. It's low body design makes it suitable for orchard and vineyard applications,
however it also has the capabilities to cut heavier scrub.
Model 1500
(0157)
Model 1800
(0126 or 0122)
Model 2100
(0120 or 0150)
Model 2400
(0128 or 0129)
Cutting Width
1.40m
1.75m
2.05m
2.35m
Overall Width
1.70m
2.00m
2.30m
2.60m
Required Tractor
HP
40-60
48-72
56-84
64-96
Gearbox
85HP
85HP
85HP
85HP
Alignment
(offset or centre)
Offset
Both
Both
Both
DELIVERY ANYWHERE IN AUSTRALIA
Page 78
MULCHERS
HIGH BODY MODEL
The High Body model is suitable for cutting a wide range of surfaces from sports ovals to
heavy scrub. Mulches orchard prunings, gorse bush, ti tree and other vegetation up to 2" in
diameter. It's advantages over a low body unit is the increased room around the rotor allowing
greater volume of vegetation to be cut without compromising the speed of operation.
Model 1800
(0123 or 0151)
Model 2100
(0121 or 0155)
Model 2400
(0127)
Cutting Width
1.40m
1.75m
2.05m
Overall Width
1.70m
2.00m
2.30m
Required Tractor HP
40-60
48-72
56-84
Gearbox
85HP
85HP
85HP
Alignment (offset or
centre)
Offset
Both
Both
MADE IN AUSTRALIA
Large Range of Blades and Bolt Kits available for all
Brand Name Mulchers
DID YOU KNOW???
OUR WEBSITE IS WORTH CHECKING FOR THE
LARGE RANGE OF PRODUCTS NOT ABLE TO BE
CONTAINED IN THIS CATALOGUE
Visit our website: www.fsme.com.au
Page 79
MULCHERS
NOBILI - Made in Italy
BNE MODEL
Features:
Best suited to medium horsepower tractors up to 50HP with
cutting height maintained by skids
Ideal for grass mowing and green prunings up to 38mm in diameter
Low profile body, no opening tailboard
PTO drive shaft with durable safety cover, heavy duty oil bath gearbox with overrun
clutch, taper locked pulleys and electronically balanced rotor
Manual side shift control or optional machine with hydraulic side shift
Available in working widths of: 1240mm / 1520mm / 1810mm / 2100mm
BNG MODEL
Features:
Multi-purpose machine fitted with a hinged tailboard that can be opened for certain
applications. Height control is maintained by adjustable skids
Universal 01 “Y” blades are fitted as standard
Ideal for grass, stubble, pasture topping, vegetable topping, re-growth and green
prunings to 75mm diameter
High profile body, opening tailboard and one mulching bar fitted to produce fine mulch
PTO drive shaft with durable safety cover, heavy duty oil bath gearbox with overrun
clutch, taper locked pulleys and electronically balanced rotor
Available in working widths of: 1580mm or 1940mm
For a comprehensive listing of all models and sizes
available, please contact a member of the
FSME Sales Team
DELIVERY ANYWHERE IN AUSTRALIA
Page 80
PALLET FORKS
BERENDS
CODE
DESCRIPTION
0297
PALLET FORKS - LINKAGE MOUNTED
0281
ADJUSTABLE PALLET FORKS - KUBOTA BOB ATTACH
0298
ADJUSTABLE PALLET FORKS - EUROHITCH
0283
COMBINATION PALLET FORK/SILAGE FORK - EUROHITCH
FARM-AID
CODE
DESCRIPTION
FA600
HEAVY DUTY 3PL PALLET FORK c/w ADJUSTABLE TINES
CHECK OUT OUR FULL RANGE OF LIFTING ATTACHMENTS FOR YOUR
TRACTOR AS WELL AS FOR YOUR FORKLIFT.
DO YOU NEED A SAFETY CAGE FOR HIGH REACH APPLICATIONS OR A
CONTAINER RAMP FOR LOADING OR UNLOADING YOUR CONTAINERS?
PLEASE CALL TO DISCUSS WITH A SALES TEAM MEMBER.
Visit our website: www.fsme.com.au
Page 81
PLOUGHS
BERENDS STUMP JUMP
The STUMP JUMP CHISEL PLOUGH is ideal for
primary cultivation. The spring action of the tines
and the chisel points have been proven to penetrate
where many other machines find the conditions too
hard.
Features:
Available in 5, 7, 9 & 11 tine sizes with tines at 12” adjustable spacing
Tractor horsepower requirement - 8 - 10HP per tine
Excellent under frame trash clearance of 520mm
Adjustable spring is designed to give a longer, more progressive action, actually
chiseling as the machine moves through the ground
Heavy duty 75 x 75 x 6mm frame
Cat 1 & 2 linkage
Silicone chrome spring steel shanks
65mm reversible points standard
Optional Holden wheel kit mounting brackets available
Optional Dart Point or Sweep Point available
BERENDS RIGID CHISEL
The RIGID TINE CHISEL PLOUGH is used in a
similar fashion to the stump jump as a primary
cultivator. The rigid tine is harder to pull as it has not
got the “jack hammering” effect of the stump jump
tine. It should also be used in country which is known
to be clean, as the tine is clamped onto the frame and
will only shear the clamp bolts under load.
The machine is ideal for lighter sandy soils where
penetration and draft are not a problem, and also for customers where price is critical.
Features:
Available in 8, 7, 9 and 11 tine models with optional wheel kits
Heavy duty 100 x 100 x 6mm frame
Tines are made from silicone chrome spring steel with 300mm spacing
DELIVERY ANYWHERE IN AUSTRALIA
Page 82
PLOUGHS
BERENDS DEEP TILLAGE
The DEEP TILLAGE PLOUGH has been designed for
shattering compact ground with minimal disturbance to the
surface.
Idea for ripping hard ground prior to cultivation and for
aerating pastures, therefore increasing water absorption and
improving the profile of soil. Can be used to renovate
pastures or for bed renovation, broad acre applications and
row cropping.
Features:
Available in 5, 7, 9 and 11 tine models
Heavy duty 100 x 100 x 9mm tine mounting frame
High tensile cast shank assembly with 24” (610mm) under frame clearance with
1” shear pin protection
Replaceable points and shin guards available with tungsten tips
Breakout force approximately 4000 ft.lbs
Tine spacing set at 12” (300mm)
Tractor horsepower requirement - 15hp per tine
Fitted standard with adjustable pair of Holden wheels for depth control
Optional coulters and hydraulic crumbler rollers available
BERENDS GROUND BREAKER
The ultimate machine for breaking open compaction without
destroying the soil structure.
The specially curved and twisted European Bellota tines are
designed to loosen the soil more effectively than the
conventional straight shank tine by gently vibrating the hard pan
from the bottom up. This produces more lateral fracturing
between the tines without bringing the sub soil to the surface or
burying residue.
Retaining surface residue will prevent top soil erosion and reduce moisture loss through
evaporation. It is also less likely to create clods on the surface, leaving a smoother finish.
Various tine configurations available. Standard in 4 & 6 tine models.
Requires approximately 20 - 35HP per tine depending on soil conditions.
Visit our website: www.fsme.com.au
Page 83
PLOUGHS
FARM-AID
CODE
DESCRIPTION
CUT
WIDTH
FA300
3 TINE, SINGLE TOOLBAR
3’
FA301
4 TINE, SINGLE TOOLBAR
4’
FA302
5 TINE, SINGLE TOOLBAR
5’6”
FA303
7 TINE, SINGLE TOOLBAR
7’6”
FA304
9 TINE, DOUBLE TOOLBAR
5’6”
FA305
9 TINE, DOUBLE TOOLBAR
7’6”
FA306
11 TINE, DOUBLE TOOLBAR
10’
FA307
15 TINE, DOUBLE TOOLBAR
10’
JARRETT CP SERIES STUMP JUMP
Solid steel (1045 grade) frame
50 x 25mm spring steel chisel tines
Strong fabricated tine clamp
CODE
TINES
WEIGHT WIDTH
MIN HP
REQ
CP150
5
310kg
1.5m
40
CP210
7
400kg
2.1m
50
CP270
9
490kg
2.7m
60
CP330
11
590kg
3.3m
70
DELIVERY ANYWHERE IN AUSTRALIA
Page 84
PLOUGHS
JARRETT DR SERIES DEEP TILLAGE
Solid steel 75 x 75 DURAX frame
16mm Bisalloy steel tines
High kg/tine ratio
(for maximum penetration)
Adjustable depth control wheels
CODE
TINES
WEIGHT
WIDTH
MIN HP
REQ
DR225
5
500kg
2.2m
60
DR337
7
700kg
3.3m
75
DR409
11
900kg
4.0m
90
MURRAY SERIES 62 RIGID CHISEL
The Murray Series 62 RIGID CHISEL PLOUGH provides the maneuverability and ease of
operation of a linkage mounted implement.
It is suited to shattering crusted soils for primary seedbed preparation, and breaking up hard
pans to improve drainage and root preparation.
CODE
TINES
WEIGHT
MIN HP
REQ
62700
7
318kg
70
62900
9
491kg
90
62110
11
499kg
110
For further models, please refer to CULTIVATORS section Pages 14-24
Visit our website: www.fsme.com.au
Page 85
PUMPS
SHURFLO
8000 SERIES 12 VOLT DC PUMPS
There are three 8000 series Shurflo pumps available, ranging from
4.5L/min to 6.8L/min open flow and 60psi to 100psi.
Ideal for agricultural and industrial applications, hand spraying, fluid
transfer, boom spraying, cooling, caravans, camping and marine applications
2088 SERIES 12 VOLT DC PUMP
The 2088 series diaphragm pump is an ideal choice for higher flow
applications such as boom spraying and fluid transfer with a 11.3L/min
open flow.
FIN COOLED 12 VOLT DC PUMP
Ideal for larger duty cycle application, aluminium heat sink
crankcase design dissipates heat build up from electric motor.
Capacity of 13.6L/min open flow, max. pressure 310kPa (45psi).
Built in on/off pressure switch, viton valves & Santoprene
diaphragm.
24 VOLT DC PUMP
Available in 11.3L/min, 310kPa (45psi) open flow with on/off demand
pressure switch. Compact size ½” BSP male ports. Ideally suited to any
machine fitted with 24 volt DC systems (eg bulldozers, trucks and road
sweepers).
240 VOLT AC PUMP
These durable and efficient positive displacement diaphragm pumps are
available in 4.5L/min, 413kPa (60psi), or 4.5L/min, 689kPa (100psi).
Open flow with on/off demand pressure switch fitted as standard.
Compact size, 3/8” BSP female ports with diaphragms that are ideally
suited to carpet cleaning applications. (Warning - must be wired by a
certified electrician.)
Other Makes and Models available, Please contact us for
further information.
DELIVERY ANYWHERE IN AUSTRALIA
Page 86
PUMPS
SELECTA
All Selecta diaphragm pumps are built for 540RPM operation, are Self-priming and
designed so no special tools are required for service. Tough and reliable they will run dry
without risk of damage. All pumps are supplied with appropriate hose connections,
mounting base plates and 1 3/8” six splined shaft. Some models are available with keyed
shaft.
BP20/15
Output @ 540RPM - 19L/min
Max. pressure (kPa / psi) - 1500 / 218
HP required @ max. pressure = 0.83
APS41
Output @ 540RPM - 38L/min
Max. pressure (kPa / psi) - 4000 / 580
HP required @ max. pressure = 4.1
P48
Output @ 540RPM - 51L/min
Max. pressure (kPa / psi) - 3000 / 435
HP required @ max. pressure = 4.1
BP60/20
Output @ 540RPM - 58L/min
Max. pressure (kPa / psi) - 2000 / 290
HP required @ max. pressure = 3.3
BP75/15
Output @ 540RPM - 68L/min
Max. pressure (kPa / psi) - 1500 / 218
HP required @ max. pressure = 2.7
BP125/20
Output @ 540RPM - 121L/min
Max. pressure (kPa / psi) - 2000 / 290
HP required @ max. pressure = 2.7
Visit our website: www.fsme.com.au
Page 87
PUMPS
BP151/20
Output @ 540RPM - 138L/min
Max. pressure (kPa / psi) - 2000 / 290
HP required @ Max. pressure = 7.8
SELECTA
Selecta motorized pumping units provide a go-anywhere pressure pumping unit in a wide
range of sizes and capacities.
Each unit consists of a matched engine and pump, control valve, brass plate, hose connections
and in most cases pressure gauge as standard equipment.
MC20/20 4 STROKE
Pressure accumulator with pressure gauge
Honda Engine GX120
Oil backed diaphragm pump
Direct coupled to motor
Adjustable pressure regulator
1 metre maximum suction lift
Max Output - 18.5L/min
Max. pressure (kPa / psi) - 2000 / 290
MC60/20 4 STROKE
Pressure accumulator with pressure gauge
Honda Engine GX160
Oil backed diaphragm pump
Direct coupled to motor
Adjustable pressure regulator
1 metre maximum suction lift
Max Output - 58L/min
Max. pressure (kPa / psi) - 2000 / 290
For further models please refer to FIRE FIGHTING EQUIPMENT section.
DELIVERY ANYWHERE IN AUSTRALIA
Page 88
RAMPS
ATV RAMPS (ATV-03)
Tough, lightweight and compact design
Safety strap and lip to avoid slippage
Folds in half for easy storage
450kg capacity
MEDIUM DUTY RAMPS (ATV-10)
Compact design made from tough lightweight aluminium
Curved design increases clearance
Safety strap and lip to avoid slippage
Folds in half for easy storage
625kg capacity
HEAVY DUTY RAMPS (ATV-11)
Ideal for mini dingo’s, excavators and skid
steers
Compact design made from tough lightweight aluminium
Single piece design with carry handle
1800kg capacity
Larger models available, please contact a member of the FSME
Sales Team.
REAR END LOADERS
BERENDS
STD
(0030)
SHORT
(0031)
LENGTH OF
BOOM
2.05m
1.60m
TRACTOR HP
REQUIREMENT
25-70
25-70
MAX LIFT
HEIGHT
1.80m
1.35m
SPECIFICATIONS
FARM-AID
FA401-1/2 YARD CAPACITY - 2.0m Length of Arm
Visit our website: www.fsme.com.au
Page 89
RIPPERS & PIPELAYING ATTACHMENTS
BERENDS
Berends rippers enable you to do a lot of hard work with minimum effort.
Ideal for breaking up hard ground, ripping up stumps or rocks, planting trees, laying
polythene pipe or removing rabbit warrens.
COMPACT RIPPER (0024)
Designed to suit compact 16 - 25HP tractors
(Cat 0 / Cat 1linkage)
100 x 25 billet
Reversible point - 225mm x 75mm x 16mm
Weight: 40kg
Maximum working depth: 350mm
Twin Rippers also available - see photo
STANDARD RIPPER (0020)
Designed to suit 25 - 70HP tractors (Cat 1 linkage with Cat 2
bushes)
150 x 32 billet
Reversible point - 225mm x 75mm x 16mm
Weight: 72kg
Maximum working depth: 500mm
HEAVY DUTY RIPPER (0021)
Designed to suit over 60HP tractors (Cat 2 linkage)
150 x 50 billet
Reversible point - 225mm x 75mm x 16mm
Weight: 100kg
Maximum working depth: 700mm
PIPELAYING ATTACHMENT
Ideally the ripper should be run through the ground prior to
pipelaying to ensure there are no obstacles, and the required
depth can be maintained. The Berends Pipelayer is easy to take on and off for this reason.
The pipe us usually rolled out next to the hole either over the tractor or with a second
operator feeding it from the side.
0029 - suits Compact Ripper (takes 65mm OD pipe)
0022 - suits Standard & Heavy Duty Rippers (takes 90mm OD pipe)
DELIVERY ANYWHERE IN AUSTRALIA
Page 90
RIPPERS & PIPELAYING ATTACHMENTS
TWIN RIPPER (0047)
Designed to suit 60+ HP tractors depending on conditions
(Cat 1 linkage with Cat 2 bushes)
Two 150 x 32 billets
Reversible points 225mm x 75mm x 16mm
Weight: 110kg
Maximum working depth: 500mm
DEEP RIPPER - 2 & 3 tine
Requires 25 - 30 HP per tine (Cat 2 linkage)
150mm x 32mm main tine section
Adjustable tines made from semi high tensile steel and
fitted with shear bolt protection
Maximum working depth: 650mm
0134 - 2 tine (weight: 320kg)
0133 - 3 tine (weight: 395kg)
MOLE DRAINER (0144)
Designed to create a “mole hole” to increase drainage
in wet pastures
Adjustable depth dual cat linkage
300mm x 20mm tapered billet with
50mm tapered foot and floating 90mm “mole”
FARM-AID PIPELAYING ATTACHMENT
FA100 - suits Berends Standard / Heavy Duty Rippers
(90mm OD pipe)
FA101 - suits Berends Compact Ripper (65mm OD pipe)
Visit our website: www.fsme.com.au
Page 91
RIPPERS & PIPELAYNG ATTACHMENTS
JARRETT
The JARRETT RIPPERS are designed for medium duty (SR series) and larger area general
farm (MR series) ripping and subsoil aerating. The unique optional “mole” attachment allows
easy poly pipe laying.
Robust construction
Reversible point
High strength 150mm x 32mm steel tine (s) with bevelled leading edge
125mm x 9mm RHS frame
MODEL
TINES
FRAME
WEIGHT
MIN HP
REQ
CAT
SR
1
n/a
100kg
20 - 60
1/2
MR2
2
1.8m
250kg
40
2
MR3
3
1.8m
310kg
60
2
MR4
4
1.8m
370kg
80
2
DELIVERY ANYWHERE IN AUSTRALIA
Page 92
RIPPERS & PIPELAYING ATTACHEMENTS
DAKENAG
LITTLE “RIPPA” (85005DC)
Designed for the “weekend farmer” with compact tractor up to 35HP
Height adjustable leg
Optional pipelaying attachment takes 1” poly pipe
Cat 0 / 1
STANDARD (85000DC)
suits up to 60HP tractors
Fixed leg length
Optional pipelaying attachment takes 2” poly pipe
Cat 1
MULTI TINE RIPPERS
Ideal for ripping hard pan soils, preparation for tree lines and removing rabbit warrens.
CODE
MODEL
TINES
WEIGHT
61214DC
4’
4
86kg
61215DC
5’
5
99kg
61216DC
6’
6
113kg
Full range of spares for Brand Name Rippers. Please contact the
FSME Sales Team
Visit our website: www.fsme.com.au
Page 93
ROTARY HOES
BREVIGLIERI - Made in Italy
“All models come with a 2 year manufacturers warranty”
BREVI B25S / B35S Side Shifting Rotary Hoes
Features include:
85 - 145cm working widths
Side chain drive with auto tensioner
Slip clutch
CE safety guards
C blades
Front depth wheels optional
Tractor HP requirement 10 - 35HP
BREVI B40F Rotary Hoes
Features include:
82 - 162cm working widths
Manual offset with lever
Side chain drive with auto tensioner
Slip clutch
C blades
CE safety guards optional
Tractor HP requirement 15 - 40HP
BREVI B83 Rotary Hoes
Features include:
155 - 230cm working widths
Side gear drive
Slip clutch
CE safety guards
6 C blades per flange
Front depth wheels optional
Tractor HP requirement 10 - 35HP
DELIVERY ANYWHERE IN AUSTRALIA
Page 94
ROTARY HOES
BREVI B103 Rotary Hoes
Features include:
185 - 230cm working widths
Larger models also
100HP multi speed gearbox
available upon
Side gear drive
request.
Slip clutch
CE safety guards
6 L blades per flange
Rear door with spring & pin adjustment
Floating front hitches
Front depth wheels, side discs (pair) & wheel track eradicator (each) optional
Tractor HP requirement 50 - 100HP
BREVI B123 Rotary Hoes
Features include:
205 - 300cm working widths
120hp multi speed gearbox
with rear PTO (540 / 1000rpm)
Side gear drive
Slip clutch
CE safety guards
6 L blades per flange
Floating front hitches
Front depth wheels, side discs (pair) & wheel track eradicator (each) optional
Tractor HP requirement 60 - 120HP
Why not contact us for all your spare parts requirements
for your tractors or machinery?
Visit our website: www.fsme.com.au
Page 95
ROTARY HOES
SICMA - Made in Italy
SA-K Series - light weight compact fixed machine
CODE
MODEL
WORKING
WIDTH
TRACTOR
HP REQ
18100
SA-K 1000
1.0m (39”)
15 - 30
18120
SA-K 1200
1.2m (47”)
20 - 30
ZLL / SB Series - light weight vineyard / orchard application
CODE
MODEL
WORKING
WIDTH
TRACTOR
HP REQ
18508
ZLL80
0.8m (32”)
15 - 35
18520
SB120
1.2m (47”)
20 - 35
18540
SB140
1.4m (55”)
25 - 35
CS Series - medium / heavy duty fixed machine
CODE
MODEL
WORKING
WIDTH
TRACTOR
HP REQ
19000
CS135
1.35m (53”)
30 - 50
19100
CS145
1.45m (57”)
35 - 50
19200
CS165
1.65m (65”)
40 - 50
DELIVERY ANYWHERE IN AUSTRALIA
Page 96
ROTARY HOES
SMR Series - medium duty fixed machine
CODE
MODEL
WORKING TRACTOR
WIDTH
HP REQ
25000
SMR160
1.6m (63”)
40 - 70
26000
SMR185
1.85m (73”)
45 - 70
27000
SMR210
2.1m (83”)
50 - 70
SPR Series - heavy duty fixed machine
CODE
MODEL
WORKING TRACTOR
WIDTH
HP REQ
28000
SPR185
1.85m (73”)
65 - 90
28500
SPR210
2.1m (83”)
70 - 90
29000
SPR235
2.35m (92”)
75 - 90
We have full workshop facilities
available for repairs or modifications to
your machinery and equipment.
PREMIER ENGINEERING (QLD) PTY LTD
Repetition and General Engineering
Guillotine and Pressbrake Facilities
Materials Handling Equipment Manufacturers
Visit our website: www.fsme.com.au
Page 97
SEEDERS
EARTHWAY - Made in USA
PRECISION GARDEN SEEDER (1001B)
A real gem and labour saver that makes planting gardens a breeze!
The Precision Garden Seeder opens the soil, plants and spaces
seeds, covers the seed, packs the soil and marks the next row . . . . .
all in one pass
The extensive range of easy-to-change seed plates means over 20
different common vegetable seed varieties can be planted.
The Precision Garden Seeder’s lightweight and super tough
construction ensure it is easy to handle. The use of corrosion
resistant materials give owners years of trouble free use.
Each new seeder purchased comes with 6 different planting plates (corn, bean, pea, radish,
carrot and beetroot)
TECHNIC - PLUS Air Seeders
TURBO - Jet Super 8 and 10
OKO TURBO 02 and 05
AGROMASTER SEED DRILLS
AGROMASTER Coulter Tine Seed Drill
The AGROMASTER spring release coulter drill has many new
features to assist Australian and New Zealand farmers plant a
wide range of small to large seeds in prepared beds or over
sow pasture. The spring release coulter is a combination of a
disc and knife soil opening system to plant seed at a consistent
planting depth. The spring release system allows the tine to
stump jump and clear any trash build up.
Made in Austria
DAKENAG “C” SEEDER
The “C” seeder can handle a variety of seeds and is a
cheap and effective way of over-sowing pastures in
any terrain.
The standard box is 7’ with 14 sowing cups each 6”
apart. Sowing capacity is approximately 15kg.
Easily attached to any implement.
DELIVERY ANYWHERE IN AUSTRALIA
Page 98
SLASHERS
BERENDS
BERENDS slashers represent the best value in slashers available in Australia today.
The first point to note on the slasher is the strength of its drive. All machines are made highly
competitive in price even though the best quality (and most expensive) components are used.
Such components which include the slasher drive-shafts are made in Italy and are fitted with
integrated clutches which are much superior compared to a separate clutch as there is less
wearing parts involved and tolerances are much higher.
TA SERIES
“Great value for money”
A lighter duty, dual mount slasher for grass and light work
to suit smaller and compact tractors.
Features include:
Body designed with 3mm top plate and strong 6mm
thick adjustable skids
Italian made Bondioli & Pavesi Series 2 PTO
driveshaft with shear bolt protection rated at 900NM
Optional 2 plate slip clutch with Series 4 shaft (standard on TA135 & TA150 models)
Cat 1 linkage with both offset and centre mount positions
Hardened & tempered stepped/bushed slasher blades
Standard with full length hinging rear steel stone flap and front rubber guard
Adjustable skids have cutting height range of 25 - 100mm
40HP Oil lubricated gearbox
Floating headstock
Model
TA100 (0350)
TA120 (0351)
TA135 (0349)
TA150 (0364)
Cutting Width
1030mm
1170mm
1360mm
1460mm
Overall Width
1129mm
1270mm
1460mm
1560mm
Overall Length
1120mm
1270mm
1470mm
1580mm
Tractor HP
18 - 30
20 - 35
25 - 45
25 - 50
Weight
180kg
195kg
225kg
245kg
Visit our website: www.fsme.com.au
Page 99
SLASHERS
BERENDS EP SERIES
“Excellent value for money”
A robust lighter duty slasher to suit smaller and
compact tractors.
Australian made using high quality European components.
Features include:
Body designed to take real punishment. 3mm top plate and strong 6mm thick side
panels (adjustable skid models only) prevent denting
Bondioli & Pavesi Series 4 PTO driveshaft with 2 plate slip clutch protects slasher &
tractor
40HP Oil lubricated gearbox
Cat 1 / 2 linkage
Hardened & tempered stepped/bushed slasher blades
Available in 4 widths with either painted or galvanised deck
Rigid headstock for better structural support
Fitted standard with safety chains and guards for front & rear protection.
Model
EP100
(0051 /
0051GAL)
EP120
(0056 /
0056GAL)
EP135
(0061 /
0061GAL)
EP150
(0062 /
0062GAL)
Cutting Width
1030mm
1170mm
1360mm
1460mm
Overall Width
1120mm
1270mm
1460mm
1560mm
Overall Length
1120mm
1270mm
1470mm
1580mm
Tractor HP
18 - 30
20 - 35
25 - 45
25 - 50
Weight
185kg
200kg
230kg
250kg
Optional Extras:
Over-run clutch to suit tractors with single stage clutch
Upgrade to Italian gearbox available
Slasher wheel kit (pneumatic wheel)
DELIVERY ANYWHERE IN AUSTRALIA
Page 100
SLASHERS
BERENDS HD SERIES
A slasher manufactured for rugged Australian conditions,
heavy built using top quality components to give you the
best value for money obtainable.
Features include:
One piece body made from 5mm quality steel. Excellent under frame clearance clears
cut material quickly
Bondioli & Pavesi Series 5 PTO driveshaft with 2 plate slip clutch protects slasher &
tractor
75HP Oil lubricated gearbox
Cat 1 / 2 linkage
Hardened & tempered straight / stepped bushed slasher blades
Rigid headstock for better structural support
Standard with front and rear chain guards & document holder
Model
HD153
(0076 /
0076GAL)
HD180
(0081 /
0081GAL)
HD200
0110 /
0110GAL)
Cutting Width
1450mm
1750mm
1950mm
Overall Width
1600mm
1900mm
2080mm
Overall Length
1580mm
1880mm
2060mm
Tractor HP
40 - 70
50 - 90
60 - 100
Weight
340kg
420kg
490kg
Optional Extras:
Upgrade to Italian gearbox
Heavy duty slasher wheel kit
Optional floating top link chain bracket
Visit our website: www.fsme.com.au
Page 101
SLASHERS
BERENDS EHD SERIES
A rugged, extra tough slasher built to take real
punishment from continuous work.
Features include:
Extra strong build with exceptionally strong
perimeter and centre cross members where it counts
Headstock made from heavy angle and RHS and fitted with floating (toggle) top link
as standard
The rotor beam is manufactured from hardened and tempered 100mm x 12mm spring
steel
Standard with Extra Heavy Duty 110HP Italian precision gearbox, and heavy duty A8
PTO shaft with 4 plate adjustable clutch
Standard with adjustable skids
Model
EHD180
(0094)
EHD180
(0087)
EHD210
(0097)
EHD210
(0089)
Cutting Width
1750mm
1750mm
2005mm
2050mm
Overall Width
1960mm
1960mm
2200mm
2200mm
Overall Length
1950mm
1950mm
2200mm
2200mm
Tractor HP
60 - 120
60 - 120
75 - 130
75 - 130
Mounting
centre
offset
centre
offset
Weight
600kg
600kg
635kg
635kg
Optional Extras:
Solid Rubber Wheel Kit
ALSO AVAILABLE AS A “CONTRACTOR PACKAGE”
Same as above models however complete with hot dipped galvanised
body, dual solid rubber wheel kits and additional skid wear runners.
DELIVERY ANYWHERE IN AUSTRALIA
Page 102
SLASHERS
BERENDS WARRIOR SERIES
The strongest slasher in the Berends range which is
ideal for contractors.
Features include:
Extra stong build with exceptionally strong
perimeter and centre cross members where it
counts
Headstock made from heavy angle and RHS and fitted with floating (toggle) top link
as standard
Unlimited horse power gearbox with unbreakable 90mm output shaft and heavy
duty Series 8 PTO shaft with 4 plate adjustable slip clutch
Rotor beam manufactured from hardened and tempered 100mm x 12mm spring steel
Twisted and stepped blades create an updraft effect which lifts grass flattened by
tractor wheels
Standard with adjustable skids
Model
WARRIOR180
(0103)
WARRIOR180 WARRIOR210 WARRIOR210
(0105)
(0100)
(0109)
Cutting Width
1750mm
1750mm
2005mm
2050mm
Overall Width
1950mm
1950mm
2200mm
2200mm
Overall Length
1950mm
1950mm
2200mm
2200mm
Tractor HP
100 +
100 +
100 +
100 +
Mounting
centre
offset
centre
offset
Weight
700kg
700kg
805kg
805kg
Optional Extras
Solid Rubber Wheel Kit
Also available as a “CONTRACTOR PACKAGE”
Same as above models, however complete with Hot Dipped Galvanised
body, dual solid rubber wheel kits and additional skid wear runners.
Visit our website: www.fsme.com.au
Page 103
SLASHERS
BERENDS SIDE DELIVERY SERIES
Specially designed and versatile heavy duty slasher ideal
for orchard and vineyard use.
Features include:
Side delivery function deposits cut material from the
left of the slasher at the base of vines and tress,
however can be used as a conventional slasher when
the side flap is closed. This unique design makes the slasher ideal for broad acre use
as it does not form windrows but spreads the material evenly over the ground surface.
This slasher can even be used for hay cutting.
Unique suction uplift blades swinging on hardened bushes.
Supplied with a heavy duty 75HP gearbox. The PTO shaft is fitted with an adjustable
slip clutch to protect the machine.
Slasher comes standard offset 12” to the left (in the direction of travel) to allow closer
access to trees / fences etc. Centre line versions available upon request.
Optional extras:
Rear roller
Heavy duty wheel kit
Does your Slasher
comply with the latest
OH&S Regulations ?
Model
SD153
(0090
0090GAL)
HD180
(0093/
0093GAL)
Cutting Width
1450mm
1750mm
Overall Width
1760mm
2060mm
Overall Length
1810mm
2110mm
Tractor HP
40 - 70
50 - 90
Weight
470kg
490kg
Did you know that
mandatory Worksafe
regulations for slashers
came into force in
September 2011? Many
slashers currently on
the market in Australia
do not meet these new
regulations.
Your One Stop Machinery Shop
DELIVERY ANYWHERE IN AUSTRALIA
Page 104
SLASHERS
BERENDS TWIN ROTOR SERIES
Heavy duty slashers designed for tough conditions - available in trailing or three point linkage
models.
Features include:
Available in 8’, 10’ & 12’ 3PL models or 10’ and 12’ trailing models.
Trailing models fitted with 14” light truck tyres and 3PL models fitted with solid
rubber tyres. Puncture proofing is available.
Twin rotors fitted to two 75HP end gearboxes and connected by an extra heavy 110HP
centre gearbox. Two-plate slip clutch between each gearbox provides gearbox
protection.
Contra rotating rotors form a flat windrow behind the centre of the slasher, however,
two small windrows can be created by reversing the direction of the rotors.
Model
(0101)
8’
3PL
(0102)
10’
TRAILING
(0104)
10’
3PL
(0112)
12’
TRAILING
(0114)
12’
3PL
Cutting Width
2300mm
2900mm
2900mm
3500mm
3500mm
Overall Width
2520mm
3120mm
3120mm
3720mm
3720mm
50 +
60 +
60 +
70 +
70 +
620kg
825kg
875kg
925kg
975kg
Tractor HP
Weight
Large Range of Blades and Bolt Kits available for all
Brand Name Slashers
Visit our website: www.fsme.com.au
Page 105
SLASHERS
BERENDS PASTURE TOPPERS
The high speed pasture topper give superior sharp,
clean cutting promoting pasture rejuvenation.
Features include:
Available only in 10’ (2900mm cutting width)
3PL model
Twin rotors fitted to two 40HP end gearboxes and connected by a 75HP centre
gearbox. Heavy duty PTO fitted with two plate slip clutch
Very high tip speed provides a cut rivaling many finishing mowers. Timed, deeply
stepped twisted blades uplift pasture and allow the topper to evenly spread the cuttings
Adjustable skids allow easy cutting height adjustment
Machine can be operated behind smaller tractors as topping is not high horsepower
work (35HP +)
** Pasture toppers are designed specifically for topping and should not be used as a slasher
or in areas where they may strike stumps, rocks or scalp the ground.**
BERENDS VINEYARD MOWER
Features include:
Twin side discharge unit - can easily be
converted to rear discharge
Twin rotors with stepped / twisted blades for
suction up lift
6mm skirt surrounds rotor producing clean side
discharge
Available in either 1600mm or 1900mm
standard sizes with either roller or wheel kit
45HP outer gearboxes connected to 75HP centre gearbox
Series 4 drive shafts are Italian made for unbeatable quality and strength
Floating / fixed top link position
Gearboxes are protected by flexible rubber couplings
DELIVERY ANYWHERE IN AUSTRALIA
Page 106
SLASHERS
DAKENAG
Dakenag slashers are feature packed to suit Hobby Farmers, and Contractors. Features like
floating headstock, laminated rotors, adjustable skids and quality components make a
package built to work and last.
Manufactured in China but designed in Australia for Australian conditions.
SERIES 405 - LIGHT DUTY (up to 30HP tractors)
40HP gear box
Adjustable skids
Laminated rotor incorporating drive block
3mm body plate
Adjustable 6” two plate slip clutch & comes with Series 4 PTO shaft
Floating headstock
2 piece chain stays connected by compensating plates
Hinged metal clutch cover
CODE
GEARBOX
WORKING
WIDTH
WEIGHT
55620DC
40
1.0m
155kg
55625DC
40
1.2m
190kg
55630DC
40
1.35m
240kg
55640DC
40
1.5m
250kg
Visit our website: www.fsme.com.au
Page 107
SLASHERS
SERIES 759 - HEAVY DUTY (up to 75HP tractors)
75HP gear box
Adjustable skids
Laminated rotor incorporating drive block
5mm body plate
Adjustable 8” two plate slip clutch & comes with
Series 6 PTO shaft
Floating headstock
2pc chain stays connected by compensating plates
Unique hinged gearbox safety cover
CODE
GEARBOX
WORKING
WIDTH
WEIGHT
55650DC
75
1.5m
330kg
55660DC
75
1.8m
390kg
CONTRACTOR SERIES
Floating headstock
Headstock centrally mounted
4 position adjustable skids
Clevis hitch
Hard wearing laminated spring steel
rotor assembly
6mm plate body
Reversible skids
Optional depth wheels available
CODE
GEARBOX
WORKING
WIDTH
WEIGHT
56100DC
75
1.8m
460kg
56904DC
130
1.8m
560kg
59910DC
130
2.1m
700kg
DELIVERY ANYWHERE IN AUSTRALIA
Page 108
SLASHERS
FINISHING MOWER
Designed & priced for the “weekend” farmer with up to
35HP tractor.
Available in 4’, 5’ & 6’ models.
FARM TECH
Australian designed and Australian made.
ECONO SERIES
Standard Features:
Folded 3mm plate top hat design for extra strength & durability.
40HP / 50HP gearbox with steel grass guard to
protect seal.
Reinforced, folded, heavy duty skids.
Floating headstock to follow ground contour.
Cat 1 - 3PL mounting pins.
16mm thick frame.
Offset option standard.
CODE
GEARBOX
CUTTING
WIDTH
HP REQ
E40-100
40
1.0m
15 - 25
E40-120
40
1.2m
20 - 30
E40-135
40
1.35m
25 - 35
E40-150
40
1.5m
30 - 40
E40-160
40
1.6m
35 - 45
E50-120
50
1.2m
25 - 35
E50-135
50
1.35m
30 - 40
E50-150
50
1.5m
35 - 45
E50-160
50
1.6m
50 - 60
E50-180
50
1.8m
50 - 60
Visit our website: www.fsme.com.au
Page 109
SLASHERS
HD SERIES
Standard Features:
Folded 5mm plate top hat design for extra strength & durability
75HP / 130HP gearbox with steel grass guard to protect seal
Reinforced, folded, heavy duty skids
Floating headstock to follow ground contour
Cat 2 - 3PL mounting pins
16mm thick frame
Offset option standard
CODE
GEARBOX
CUTTING
WIDTH
HP REQ
HD1200
75
1.2m
50 - 65
HD1350
75
1.35m
55 - 70
HD1500
75
1.5m
60 - 75
HD1800
75
1.8m
65 - 80
HD1500/130
130
1.5m
90 - 110
HD1800/130
130
1.8m
90 - 110
HD2100/130
130
2.1m
90 - 110
Full range of
replacement
parts and
spares
available for
brand name
slashers and
machinery
DELIVERY ANYWHERE IN AUSTRALIA
Page 110
SLASHERS
RHINO SERIES
Standard Features:
Folded 6mm plate top hat design deck for clean lines, extra strength and durability
Centre box section for greater integral strength for gearbox mounting
130HP rated gearbox
Heavy duty 3 blade triangle cutting rotor standard.
Heavy duty series 8 PTO shaft
Reinforced folded, heavy duty skids
Floating headstock to follow ground contour
Cat 2 - 3PL linkage mounting pins
16mm thick frame
Offset optional
CODE
GEARBOX
CUTTING
WIDTH
HP REQ
R-HD1800
130
1.8m
100 - 125
R-HD2100
130
2.1m
120 - 140
Call us for blades
and bolt kits,
gearboxes and
spares, PTO shafts,
skid plates,
replacement
wheels, almost any
wear part.
Talk to one of our
Sales Team
Members today to
discuss your
requirements.
Visit our website: www.fsme.com.au
Page 111
SLASHERS
JARRETT
Australian designed and Australian made.
M SERIES
General Construction:
5mm steel deck sheet
5mm steel reinforced gearbox plate (10mm / 15mm total thickness)
Obstruction free top deck (no debris collection points)
Strong A frame with gusset & Cat 1 lifting pins
Built-in front and rear discharge deflector plates
Adjustable skids
Quality high speed 1:1.97 ratio gearbox
Fabricated cutting beam for maximum strength
CODE
GEARBOX
WIDTH
MIN HP
WEIGHT
MD120
40
1.2m
20
230kg
MD135
40
1.35m
25
260kg
MD150
40
1.5m
35
290kg
MDX150
75
1.5m
45
330kg
MDX180
75
1.8m
55
400kg
Large range of Herbicides and Pesticides available.
Please contact the FSME Sales Team for your needs today
Call today
with your
requirements
07 32775388
DELIVERY ANYWHERE IN AUSTRALIA
Page 112
SLASHERS
H SERIES
General Construction:
5mm steel deck sheet
12mm steel reinforced gearbox plate (17mm total thickness)
Obstruction free top deck (no debris collection points)
Obstruction free cutting chamber
Strong A frame with gusset & Cat 1 / 2 lifting pins
Built-in front and rear discharge deflector plates
Adjustable skids with top gusset
Quality Australian made high speed 1:1.97 ratio gearbox
Fabricated cutting beam for maximum strength
CODE
GEARBOX
WIDTH
MIN HP
WEIGHT
HM150
75
1.5m
45
350kg
HM180
75
1.8m
55
430kg
HR150
75
1.5m
45
500kg
HR180
75
1.8m
55
580kg
HD150L
45
1.5m
35
350kg
HD150
75
1.5m
45
380kg
HD180
75
1.8m
55
450kg
HD210
75
2.1m
65
520kg
Are you needing a replacement seat or any other tractor parts?
Visit our website: www.fsme.com.au
Page 113
SLASHERS
E SERIES
General Construction:
5mm steel deck sheet
12mm steel reinforced gearbox plate
(17mm total thickness)
Obstruction free top deck (no debris collection points)
Obstruction free cutting chamber
Strong RHS linkage frame with clevis hitch & Cat 2 lifting pins
Built-in front and rear discharge deflector plates
Adjustable skids with top gusset
Contour float / fixed headstock
Quality Australian made high speed 1:1.95 / 1:1.5 ratio gearbox
Fabricated cutting beam for maximum strength and shock protection
CODE
GEARBOX
WIDTH
MIN HP
WEIGHT
EHD150
110
1.5m
50
580kg
EHD180
110
1.8m
60
680kg
EHD210
110
2.1m
70
780kg
DELIVERY ANYWHERE IN AUSTRALIA
Page 114
SLASHERS
T SERIES
General Construction:
5mm steel deck sheet
12mm steel reinforced gearbox plate (17mm total thickness)
Obstruction free top deck (no debris collection points)
Obstruction free cutting chamber
Strong RHS linkage frame with clevis hitch lifting pins
Built-in front and rear discharge deflector plates
Adjustable skids with top gusset
Contour float / fixed headstock
Quality Australian made high speed 1:1.95 ratio gearbox
Fabricated cutting beam for maximum strength and shock protection
CODE
GEARBOX
WIDTH
MIN HP
WEIGHT
EHDT240
110
2.4m
70
700kg
EHDT300
110
3.0m
80
800kg
EHDT360
110
3.6m
90
900kg
Construction Site & Safety / Diesel Tanks / Excavator Attachments /
Grease Equipment / Loading Ramps / Oil Transfer / Skid Steer Attachments /
Water Transfer / Water Cartage / Tanks / Trash Pumps
Visit our website: www.fsme.com.au
Page 115
SPRAY EQUIPMENT
SILVAN
SELECTA SPOTPAK RANGE
The Selecta Spotpak range features the highest
quality components to give you hassle free
spraying where ever you are.
All purpose 12 volt sprayer ideal for
spot spraying
Rugged 20, 50, 100 & 200 litre tanks
Shurflo 12 volt pumps on all models
Spotjet stainless steel spraygun with adjustable nozzle and 6m of hose
Non-spill lid, in-built carry handles
Pump is recessed within tank for protection
12 volt on/off switch and wiring loom, alligator clips, fuse
Tie-down locating channels for straps
Optional booms and pressure regulators available
SELECTA RAKPAK RANGE
The Selecta Rakpak sprayer has been designed to fit neatly on most ATV bikes and meet the
strict weight requirement of these vehicles. All fitted with your choice of high quality and
reliable 12 volt pumps, with a full spare parts back-up supply.
All purpose 12 volt sprayer ideal for spot spraying on quads
Rugged 50 & 70 litre tanks
Shurflo 12 volt pumps
Selecta Pak pump on 50 litre models
Non-spill lid, chemical spill barrier
Pump is recessed within tank for protection
Moulded hose storage rack
Spotjet stainless steel spraygun with adjustable
nozzle and 6m hose
12 volt on/off switch and wiring loom, alligator clips, fuse
Tie-down locating channels for straps
DELIVERY ANYWHERE IN AUSTRALIA
Page 116
SPRAY EQUIPMENT
SELECTA SQUATPAK RANGE
The Selecta Squatpak spraying tanks are available either as
fully furnished spraying units complete with 12 volt or
motorised pumps and hose kits, or as bare tanks to fit your
own pumps and hose combinations.
Professional series 12 volt sprayer ideal for spot and
boom spraying
Rugged 400 litre tank with internal baffle to reduce
water surge
Non-spill lid
Shurflo 12 volt pump which is recessed for protection or Selecta Comet
diaphragm pump Honda engine
Hose reel and hose available standard on some models
Spotjet stainless steel spraygun with adjustable nozzle and 6m of hose
12 volt on/off switch and wiring loom, alligator clips, fuse
Tie-down locating channels for straps
Optional booms and pressure regulators available
SELECTA WEEDPAK RANGE
The Weedpak range of 12 volt sprayers are ideal for
hobby and lifestyle farmers and the home gardener.
All purpose 12 volt sprayer for home garden
and farm use
20, 50 & 100 litre tanks
Screw down lid and breather
Selecta Pak 12 volt pump which is recessed for protection
Telescopic spray lance and 6m of hose
12 volt on/off switch and wiring loom, alligator clips, fuse
Tie-down locating channels for straps
Full range of chemicals available. Please call today to discuss your needs with one of our
Sales Team Members
Visit our website: www.fsme.com.au
Page 117
SPRAY EQUIPMENT
SELECTA TRUKPAK / UTEPAK
The professional’s portable sprayer for those who require
the flexibility of different pumps and boom options. They
are compact, self-contained and can sit on the back of
utility, truck or trailer.
Professional Series 12 volt sprayer ideal for spot and
boom spraying
Rugged 100 & 200 litre tanks
Shurflo 12 volt pumps on both models with inline
filter
Spotjet stainless steel spraygun with adjustable nozzle and 6m of hose
Non-spill lid, in-built carry handles, chemical spill barrier
Pump is recessed within tank for protection
12 volt on/off switch and wiring loom, alligator clips, fuse
Tank lid basket strainer
Optional booms and pressure regulators available
SILVAN TRAYLINK SPRAYER
This new unit is ideal for “Plug’n’Play” spraying. Perfect for small Cat 1 linkage
applications, it can also be mounted on the tray RTV. It features a 20 l/min open flow
12 volt pump with 6 metres of 10mm delivery hose with the Selecta Spotjet spray gun and
boomless nozzle kit as standard.
Suitable for mounting compact tractors and
utility / trailer trays
Rugged 200 and 300 litre tanks
Aquatic high capacity 12 volt pump 20 l/min
Robust multi-purpose frame with Cat 1 pins
Non-spill lid
Pump is recessed within frame for protection
Hose storage rack
12 volt on/off switch and wiring loom, alligator clips, fuse
Hypro boomless nozzle sprays up to 10m wide
Control valve and pressure gauge
DELIVERY ANYWHERE IN AUSTRALIA
Page 118
SPRAY EQUIPMENT
SELECTA TROLLEY SPRAYERS
Your portable sprayer for home, garden and farm.
Rugged 20 and 25 litre tanks, non-spill lid
Shurflo 12 volt pumps
Easy to push or tow with Ezy Glide wheels
Spotjet stainless steel spraygun with adjustable
nozzle and 6m of hose
Rechargeable battery - charger supplied
Pump cover on Professional model
SELECTA LIGHTFOOT TRAILED SPRAYERS
The Selecta Lightfoot trailed series makes spot spraying
and boom spraying easy. Choose which boom and
operations you require and then check the accessories
table to select which Lightfoot and pump combination
suits your application.
Ideal for towing behind compact tractors and
quad bikes
Heavy duty 100 & 300 litre tanks, non-spill lid & drain outlet
Robust chassis with tow hitch
Shurflo 12 volt pump which is recessed for protection or Selecta Comet diaphragm
Honda engine available
12 volt on/off switch and wiring loom, alligator clips, fuse on 12 volt models
Spotjet stainless steel spraygun with adjustable nozzle and 6m of hose
Pneumatic tyres on steel rims
Optional booms and pressure regulators available
Visit our website: www.fsme.com.au
Page 119
SPRAY EQUIPMENT
SILVAN ECONOPAK & PASTUREPAK- LINKAGE
SPRAYERS
SILVAN SLIMLINE - LINKAGE SPRAYERS
SILVAN SUPAFLOW - LINKAGE SPRAYERS
TRAILED SUPAFLO SPRAYERS
For all models and sizes available, please contact a member of the
FSME Sales Team
Please check out our website as it is constantly being updated with the latest
products available on the market.
DELIVERY ANYWHERE IN AUSTRALIA
Page 120
SPRAY EQUIPMENT
CHAPIN HAND SPRAYERS
Ideal for the home gardener and will make low volume spot spraying easier and more
efficient.
4 & 8 LITRE CHAPIN SURESPRAY PORTABLE SPRAYERS
Suitable for Herbicide, Pesticide, Fertiliser, Degreaser
Strong polyethylene tank with funnel top opening
Spray gun includes both a brass and plastic adjustable nozzles
Includes clip-on spray shield and anti-clog filter
Includes a 125ml (½cup) measuring cup which latches to spray
tank for storage
CHAPIN PRO SERIES GENERAL PURPOSE HAND SPRAYERS
Suitable for Insecticides, Fertilisers, Herbicides and Cleaning
Products
Equipped with Viton seals and gaskets
Corrosion resistant spray lance
Supplied with 3 different nozzles: adjustable brass, adjustable
plastic & flat fan plastic
Surespray anti-clog filter in tank
Suitable for diesel
VOLPI HAND SPRAYER
This handy sprayer features a chemical resistant tank with graduate scale and is ideal for
small spraying jobs around the farm.
Wide tank neck for easy filling
On/off trigger
Aluminium lance & brass adjustable nozzle
Pressure relief valve
Polyethylene pump and carry strap
Visit our website: www.fsme.com.au
Page 121
SPRAY EQUIPMENT
CHAPIN POLY HAND SPRAYER
An industrial, heavy duty, poly sprayer that is ideal for corrosive type liquid and most
commercial applications.
Polyethylene pump
Viton seals
Braided hose
450mm lance and fan nozzle
Pressure relief valve
Padded strap
Ideal for carpet and concrete applications
Suitable for diesel
CHAPIN HEAVY DUTY HAND SPRAYER (13 litre)
Heavy duty industrial sprayer with brass pump barrel capable of withstanding aggressive
solvents such as concrete sealer. Hammer toned finish provides additional protection
against denting and brass suction filter to prevent clogging.
Swage hose connections
Brass lance and fan nozzles
Viton seals
Tripoxy lined tank
Anti-clog filter
Suitable for diesel
CHAPIN INDUSTRIAL HAND SPRAYER (13 litre)
An industrial sprayer with brass pump barrel capable of withstanding
aggressive solvents such as concrete sealer.
Swage hose connections
Brass lance and fan nozzles
Viton seals
Tripoxy lined tank
Suitable for diesel
DELIVERY ANYWHERE IN AUSTRALIA
Page 122
SPRAY EQUIPMENT
SELECTA WEEDPAK BACKPACK SPRAYER
The reliable and easy to use 15 litre WeedPAK Knapsack has been
designed for the home gardener where low volume spot spraying
application is required.
15 litre unit comes with shoulder straps
Lockable spray lance trigger with fan or cone nozzle
Spray lance handle includes filter
Anti spill screw lid and strainer
Transferable left or right side mounted pump handle
CHAPIN BACKPACK SPRAYER (15 litre)
Ideal for weed control, pest control and fertilisers.
Viton equipped
4 pressure settings from 15-60psi
Easy operating spray handle for left or right
handed use
Spray handle with continuous spray feature
Supplied with 3 different nozzles: adjustable brass, adjustable plastic & flat fan plastic
Three stage filtration
Spill free lid (even when tilted)
WEEDPAK 12VOLT RECHARGEABLE SPRAYER (16 litre)
UV stabilized polytuff tank
2 stage filtration under the lid and on the suction hose in the tank
Rechargeable 12 volt battery & charger standard
Contoured design for comfort against your back
Heavily padded adjustable shoulder straps
Maximum open flow 2.6 l/min
Pressure rating 40psi, intermittent duty cycle
Viton valves & santoprene diaphragm
Run time approx 4 hours
Visit our website: www.fsme.com.au
Page 123
SPRAY EQUIPMENT
CONDOR KNAPSACK SPRAYER (18 litre)
UV stabilized Polytuff tank
Large screw down lid and strainer for quick filling
High pressure pump (1400kPa/203psi)
Pump handle can be fitted either side of tank
Large pressure chamber to minimise pumping and help
maintain constant pressure
On/off trigger, extension lance with brass adjustable nozzle
SOLO HANDHELD MINI SPRAYER 401 / 402 (1L OR 2L)
Professional mini sprayer with viton seals and lever lock.
The robust pump reaches the required operating pressure after just a
few strokes.
The vertically adjustable nozzle head makes spraying easy even in
awkward places like underneath eaves.
The high quality nozzle is fully adjustable from direct jet to the finest mist.
SOLO HANDHELD SPRAYER 456 (5 litre)
Professional pressure sprayer offering 5 litre capacity.
The 480cm³ pump generates 3 bar pressure with just a few strokes.
The large apertures allow easy cleaning.
50cm spray lance with robust grips standard.
Selection of spray nozzles supplied standard.
SOLO ACETONE HANDHELD SPRAYER 487 (11 litre)
Profession handheld sprayer with 11 litre capacity specifically for the
application of acetone dye and concrete application uses.
May also be used when applying problem chemicals, like alcohol or
ammonia.
DELIVERY ANYWHERE IN AUSTRALIA
Page 124
SPRAY EQUIPMENT
SOLO PROFESSIONAL BACKPACK SPRAYER DIAPHRAGM PUMP RANGE
(475/473D)
Designed for herbicides and chemicals in wettable powder
form as well as liquid formulations.
Fully repairable
Ability to pass small abrasive particles without damage to the
pump assembly.
Made in Germany.
No.1 in Australia.
5 year Guarantee.
SOLO PROFESSIONAL BACKPACK SPRAYERPISTON RANGE (425 / 425D)
Produces wide pressure range of up to 90psi.
Handles disinfectants, fertilisers, pesticides and formulations for
tree, shrub, and plant protection
Resistant to diesel
Fully repairable
Full range of spare parts and accessories available
SOLO BACKPACK POWER SPRAYER (433)
This high pressure sprayer from SOLO with 20L capacity reaches a
controlled operating pressure of up to 30 bar, enabling it to achieve fine
spray mist applications, even at extreme heights.
The heavy-duty engine delivers a satisfying performance.
At 30 bar - delivered by a “push-pull piston pump” can achieve a flow rate of
up to 2 l/min.
A practical drain connector underneath the container ensures complete
draining of residual media.
Equipped with a 60cm stainless steel spray tube and a pressure gauge on the
sturdy quick release handle, which allows the pressure to be matched to any
application.
Visit our website: www.fsme.com.au
Page 125
SPRAY EQUIPMENT
SOLO PORTABLE MISTER (451) - 13 litre capacity
Professional sprayer with new, powerful and low emission SOLO
engine. Comfortable support frame with padded straps and strap
tensioner.
With their high performance spray technology in Germany, SOLO
truly leads the world in power misters. Impressive spraying
capacity and low weight. These characteristics make SOLO power
tools the environmentally responsible and economical choice for
plant protection in horticultural and forestry around the world.
SILVAN MOTORISED MISTER (NBB-M18)
The motorized mister has the power to cover large areas quickly with
a horizontal throw of 12 to 14 metres for liquids.
Output capacities are 0.5 to 3 litres per minute for liquids
Reliable 73cc two-stroke Efco motor
Anti-vibration buffer suspension system
14 litre capacity poly tank
Large screw down lid and strainer
Delivery tube with variable flow adjuster
Padded shoulder frame for operator comfort
SELECTA 14L BLOWAMIST (NBB-3W650)
A necessity for any nursery, greenhouse or small orchard.
The fan forced spray mist generates a coverage deep into foliage.
Compact 2 stroke 43cc Engine
14 litre chemical tank
Chemical throw up to 15 metres
DELIVERY ANYWHERE IN AUSTRALIA
Page 126
SPRAY EQUIPMENT
SILVAN GARDEN WICK STICK APPLICATOR
The successful wick wiping method has also been adapted to general garden use in an easy to
handle, rake-size applicator. Its simple design allows liquid to flow from a long re-fillable
PVC handle into a Pistachio wick head that in turn applies a lethal dose to weeds. One wipe
does it all.
ATV and 3PL Models also available
Other style and Brand Name Wick Wipers also available, please call the FSME Sales
Team
SILVAN SPRAY GUNS &
ACCESSORIES
SPOTJET SPRAY GUN (410-46)
The Spotjet spray gun is the standard spray gun to many of Selecta’s range of 12 volt spray
units. It features strength and durability due to quality materials in the hand piece and lance
being both strong and corrosion resistant. The hand piece uses stainless steel components for
reduced wear and tear and broad chemical compatibility. An adjustable nozzle is supplied
but other nozzles can be fitted to suit more specific spray requirements.
KWAZAR TELESCOPIC SPRAY LANCE
(410-26)
One of the most popular and affordable spray lances available.
Supplied standard with fully adjustable nozzle.
Extends from 850mm to 1380mm.
SPRAY SHIELD
Helps reduce excess spray drift. Complete with swivel adjustment
and four adaptors to enable fitting to various spray guns including
PA series spraygun, Volpi, Condor, Spotpak and Weedpak sprayers.
Visit our website: www.fsme.com.au
Page 127
SPRAY EQUIPMENT - REGA
one life, one sprayer…… REGA
REGA PNEUMATIC STAINLESS STEEL SPRAYERS
The Stainless Steel Pneumatic sprayers are fully customizable. Triggers,
hoses, sprayers and more can be changed to meet your requirements.
All parts are available in DIY maintenance kits or bring it to FSME to be
serviced.
Available in 5, 8 & 9 litre units.
BUCKET (STIRRUP) PUMP (BUC)
This high pressure sprayer is ideal for applying all chemicals including
difficult non-dissolvable powders such as Bordeaux.. Made primarily from
heavy gauge brass, they are strong and durable and resist corrosion. This
unit has a cast pressure air chamber and brass ball valves which provide a
continuous flow of spray. A fully adjustable metal footrest is also fitted.
UNI SPRAYER (UNI)
This brass high quality double action sprayer is excellent for spraying flowers, shrubs and
small fruit trees in home gardens and nurseries. The long extension wand, angled at the
nozzle end for spraying under and over foliage, ensures that the operator is kept well clear
of the chemicals being applied.
GEN SPRAYER (GEN)
Long brass extension lance, angled at the nozzle, for spraying around hard to get at
places.
Includes brass nozzle, fully adjustable between jet and fine mist.
Operates by single pumping action, drawing chemicals through a plastic hose,
from a weighted strainer placed in a bucket.
Allows for greater economy in the purchase of bulk chemicals.
DELIVERY ANYWHERE IN AUSTRALIA
Page 128
SPRAY EQUIPMENT - REGA
one life, one sprayer…… REGA
TRIGGER VALVE - TRIG (30g)
COVAL HIGH PRESSURE AUTO CUT OFF VALVE
NZ3 Nozzle
COVAL GUN (50g)
NZ8 Nozzle
HIGH PRESSURE SPRAY WAND
UDDER GUN (45g)
NZ26 Nozzle
SPARE PARTS
Extensive range of parts still available for most REGA products including:
Garden, Knapsack & Pesticide sprayers
Nozzles & Boom spray components
Fire Fighting products, Flame Throwers & Burners
Tyre Pumps
Wands, Trigger Valves, Spraying Systems & Accessories
Pumps, Control Heads & Line Strainers
Visit our website: www.fsme.com.au
Page 129
STICK RAKES
BERENDS
The ideal implement for raking up sticks, prunings, light rocks
and general trash. Also suitable for pasture harrowing in some
conditions.
Many stick rakes use a very light flat tine which are only good
for light sticks and bark around the lawn. Berends stick rakes
all use 32 x 10mm cultivator “S” tines mounted at 6” spacings.
They have an under frame clearance of 400mm and are fitted
with reversible bolt on points.
This type of tine can make the stick rake a little aggressive if
using them in a lawn situation particular if the tractor is unable
to maintain the height. In this situation, it is recommended the optional wheel kit be fitted.
Available sizes: 4’, 5’, 6’, 7’6”, 9’ & 10’6”
DAKENAG
Designed for compact tractors (up to 35HP).
Replaceable spring tines
Rake comb can be angled left or right
Standard Cat 0 / 1 linkage
FARM-AID
Made in Queensland.
Heavy duty 75 x 75 x 12mm angle bottom
linkage mounts
75 x 50 x 6mm RHS main frame
Double frame for added strength
Anti-kick bar fitted for greater strength &
minimized tine breakage
¾” special spring steel round curved tines
Tines spaced 6” apart - other spacings available upon request
Tines float independently - approx 90mm max vertical movement
Rakes sit higher, approx 650mm clearance allowing more debris to be collected
DELIVERY ANYWHERE IN AUSTRALIA
Page 130
TOOLBAR TILLER COMPONENTS
Clamps &
Rigid Tines
Reversible Points
Duck Feet
Spring Tines
Plain & Scallop Discs
Furrowers
Please contact a member of the FSME Sales Team for your specific
requirements.
Visit our website: www.fsme.com.au
Page 131
WEEKEND FARMER PACKAGES
These packages have been designed for the rapidly growing small acreage land owners.
Predominately such “farmers” require implements which are used occasionally so therefore
prefer to purchase cheaper options in an effort to reduce the cost of assets left idle most of
the time.
All products are suited for compact tractors up to 35 Horsepower.
MAINTENANCE PACKAGE
1.
2.
3.
SLASHER 1.0m 405 Slasher– 55620DC
12 VOLT SPRAYER 95L - 3.8l/m Shurflow Pump Continuous Spot Sprayer
SVS 0095L0038
CARRYALL (4’) - Steel Floor 61070DC
CONSTRUCTION PACKAGE
1.
2.
3.
GRADER BLADE 61030DC
RIPPER / PIPE LAYER 85005DC / 85035DC
POST HOLE DIGGER INCLUDES 1 AUGER 81000DC (6” Auger) 81326D
COMPLETE PACKAGE - Incorporates both “Maintenance” & “Construction”
Packages
DELIVERY ANYWHERE IN AUSTRALIA
Page 132
MAJOR BRANDS INFORMATION
Crump’s history began with horse drawn spreaders around the time of the First World War.
The concept, accuracy and basic design of the 1930’s spinner spreader was so good that it
was used until replaced in 1970 by the Kurrajong series.
Both the Acacia and Kurrajong series have been improved further in recent years and are
solely manufactured in Albury NSW.
For more than 29 years, Digga has led the industry in attachment design, manufacture and
distribution. Established in 1981, Digga pioneered pendulum drilling in Australia and are
the leading manufacturer of planetary drive boring and trenching attachments.
Premier Engineering (QLD) Pty Ltd manufacture their own product line: FARM-AID,
which has had a reliable track record for many years and is still very popular with the small
farmer across Australia. All products in the range are made solely at the Coopers Plains QLD
manufacturing facility.
PREMIER ENGINEERING (QLD) PTY LTD
Repetition and General Engineering
Guillotine and Pressbrake Facilities
Materials Handling Equipment Manufacturers
John Berends Implements was established in 1966 by Mr John Berends. Based in Dandenong
Victoria, Berends make and sell more slashers, mulchers, cultivators, post hole diggers and
rotary drain diggers than anyone else in Australia.
Berends are committed to industry leadership in product reliability and are fully insured;
Visit our website: www.fsme.com.au
Page 133
MAJOR BRANDS INFORMATION
When Ferguson introduced its 20HP, 3PL tractor to Australia soon after WWII, only a few
implements were available.
Enter Vic Jarrett, a young, ambitious lad from a farming family in the Hills district of Sydney.
Vic was a qualified machinist and welder, and local farmers regularly called on him to repair
their machinery. He then turned his hand to designing and building in 1948.
Today Jarrett Implements utilises computer design facilities and fabricate implements with
automatic band saws, hydraulic punches, brake presses, computerised lathes and robotic &
MIG welders. Nearly all manufacturing processes for the complete range of implements are
performed at Jarrett’s Dural factory.
Kanga Farm Equipment & Caroni Implements have been supplying quality 3-point linkage
implements to Australian Farmers since 1981.
Kanga specialized in manufacturing and offers a range of over 20 different types of 3-point
linkage implements to suit tractors from 12 - 150HP.
Caroni is an importing company that currently represents three leading European
manufacturers and offers approximately 10 different ranges of implements to complement
those manufactured by Kanga.
Murray Agricultural Equipment has been supplying the Australian farming market with
quality Tine Harrow systems for more than 100 years. The business has specialized in
traditional factory excellence - pride in workmanship and service - since 1903.
DELIVERY ANYWHERE IN AUSTRALIA
Page 134
MAJOR BRANDS INFORMATION
Rega has been manufactured in Australia since the early 1920s and there are still products
from this early era in operation today.
one life, one sprayer…… REGA
Established in 1962, Silvan has been a pioneer in the development and manufacture of
agricultural machinery to meet the needs of Australia’s primary producers.
Always at the forefront in the development of new technology, Silvan combines strong
innovative management with a comprehensive understanding of today’s agribusiness.
German engineered and manufactured.
Solo are market leaders in professional spraying equipment for domestic and commercial
pesticides and wed control applications.
The climate and landscape of Norway’s south western region is harsh and unforgiving,
making farming in this area both difficult and challenging. Despite this, hard working men
and women have transformed this area into one of the most productive agricultural regions
in Norway. The Kverneland Group has made its own contribution to agricultural
development in the region throughout the years. Experience gained in such a tough
environment has been invaluable to Kverneland Group’s rise to becoming one of the worlds
leading supplier of implements to the professional farming community which includes the
world famous VICON spreaders.
Visit our website: www.fsme.com.au
Page 135
Aerators
Animal & Wildlife Management
Bale, Hay & Silage Equipment
Carryalls
Cultivators
Diesel Tanks & Accessories
Fencing & Drilling Equipment
Fertiliser Spreaders
Fire Control & Fighting Equipment
Grader Blades
Harrows
Livestock Handling Equipment
Mulchers
Pallet Forks
Ploughs
Pumps
Rippers
Rotary Hoes
Seeders
Slashers
Spray Equipment
Toolbar Tiller Components
Notes
Dealer
Tel: (07) 3277 5388
Fax: (07) 3277 5597
PO Box 9
54 Annie Street
COOPERS PLAINS Q 4108
Email [email protected]
www.fsme.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement