AMX NI-700 User's Manual
Installation Guide
NI-700 NetLinx
For more detailed installation, configuration, programming, file transfer, and operating
instructions, refer to the NI-700 and NI-900 NetLinx Integrated Controllers Instruction
Manual, available on-line at www.amx.com.
Rear Panel
Connectors
(Cont.):
• IR/Serial (Port 3): 4-pin 3.5 mm mini-Phoenix port is capable of
supporting high-frequency carriers of up to 1.142 MHz with the
output being capable of three electrical formats: IR, Serial, Data.
IR ports support data mode (at limited baud rates and wiring
distances).
• AXlink LED: Green LED indicates the state of the AXlink port.
• AXlink Port: 4-pin 3.5 mm mini-Phoenix (male) connector provides
data and power to external control devices.
• Ethernet Port: RJ-45 port for 10/100 Mbps communication. LEDs
show communication activity, connection status, speeds, and
mode information:
SPD (speed) - Yellow LED lights On when the connection speed
is 100 Mbps and turns Off when the speed is 10 Mbps.
L/A (link/activity) - Green LED lights On when the Ethernet cables
are connected and terminated correctly, and blinks when
receiving Ethernet data packets.
• Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector
Operating
Environment:
• Operating Temperature: 0° C (32° F) to 50° C (122° F)
• Operating Humidity: 20% - 85% RH
Included
Accessories:
•
•
•
•
2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)
4-pin 3.5 mm mini-Phoenix female connector (41-5047)
6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)
CC-NIRC IR Emitter
Other AMX
Equipment:
•
•
•
•
•
•
•
•
AC-RK Accessory Rack Kit (FG515)
CC-NIRC IR cables (FG10-000-11)
CC-NSER IR/Serial cables (FG10-007-10)
IRX-DM+ IR Sensor (FG458-10 and FG458-11)
IRX-SM+ IR Sensor (FG455-01)
PMB Pole Mount Bracket (FG531)
STS, Serial To Screw Terminal (FG959)
Surface Mount Bracket Accessory (FG525)
Overview
ATTENTION!
Verify you are using the latest version of NetLinx Studio (available for download
from www.amx.com).
NI-700 Specifications
Dimensions
(HWD):
• 1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)
• 1 rack unit high
Power
Requirement:
• 280 mA @ 12 VDC
• Power requirements are usage dependant
Memory:
• 64 MB SDRAM (not upgradeable)
• 32 MB Flash chip (not upgradeable)
• 512 Kb of Non-volatile SRAM
Microprocessor:
• 304 MIPS
Weight:
• 1.30 lbs (0.59 kg)
Port
ICSP Port #
Enclosure:
• Metal with black matte finish
Serial Port #1
1
Certifications:
• FCC Part 15 Class B, CE, and IEC 60950
Serial Port #2
2
Front Panel
Components:
• Program Port: RS-232 DB9 connector (male) can be connected to
a DB9 port on a PC. This port can be used with both Serial and
NetLinx commands.
• Configuration DIP Switch: Sets the communication parameters for
the Program port.
• IR RX LED: Red LED lights when IR data is being received via the
rear IR RX port.
• IR LED: Red LED lights during the transmission of IR or Serial
data via the rear IR port.
• I/O LEDs: Four yellow LEDs light when the rear I/O channels 1 - 4
are active. LED indicator for each I/O port reflects the state of that
particular port.
• Serial LEDs: Two sets of red and yellow LEDs light when the rear
DB9 Ports (1 & 2) transmit or receive RS-232, 422, or 485 data.
These LEDs do not reflect changes in either the RTS or CTS
when hardware handshaking is used.
• LINK/ACT: Green LED lights when the Ethernet cable is
connected and an active link is established. This LED also blinks
when receiving Ethernet data packets.
• Status: Green LED lights when the Controller is programmed and
communicating properly.
• Output: Red LED lights when the Controller transmits data, sets
channels On and Off, sends data strings, etc.
• Input: Yellow LED lights when the Controller receives data from
button pushes, strings, commands, channel levels, etc.
• ID Pushbutton: Sets the NetLinx ID (Device only) assignment for
the device.
IR/Serial Port
3
Rear Panel
Connectors:
• RS-232/422/485 (Ports 1 & 2): Two RS-232/422/485 control ports
use DB9 (male) connectors with XON/XOFF (transmit On/
transmit Off), CTS/RTS (clear to send/ready to send), and 300 115,200 baud.
• IR RX (Port 5): 4-pin 3.5 mm mini-Phoenix port is used to connect
one or more (8 maximum) IRX-SM+ swivel mount or IRX-DM+
Decora mount IR receivers.
The IR RX port functions using AMX IR codes (38 KHz and
455 KHz) and works ONLY with AMX IR Receivers such as the
IRX-DM+ and IRX-SM+.
• Digital I/O (Port 4): 4-channel binary I/O port for contact closure
with each input being capable of voltage sensing. Input format is
software selectable with interactive power sensing for IR ports.
Integrated Controller
NI-700 Specifications (Cont.)
FIG. 1 NI-700 NetLinx Integrated Controller (front view)
The NI-700 (FG2105-70) is geared to meet the specific control and automation needs
of a single room environment, where both price and functionality are the driving
requirement. This product is configured to control a limited number of video players,
projectors, lighting, thermostats, and other electronic equipment. The NI-700 provides
support for one IR/Serial Output port, two RS-232/RS-422/RS-485 ports, four Digital
Input/Output ports, and one IR RX port.
®
Port Assignment and Functionality
NI-700 Port Assignments
I/O Port
4
IR RX Port
5
Ethernet Ports used by the NI Controller
Ethernet Port Usage
Port type
Description
Standard Port #
FTP
The on-board Master has a built-in FTP server.
21/20 (TCP)
SSH
The SSH port functions using the same interface as
Telnet but over a secure shell where it uses SSL as a
mechanism to configure and diagnose a NetLinx
system.
Note: SSH version 2 is only supported.
22 (TCP)
Telnet
The NetLinx Telnet server provides a mechanism to
configure and diagnose a NetLinx system.
23 (TCP)
HTTP
The Master has a built-in web server that complies
with the HTTP 1.0 specification and supports all of the
required features of HTTP v1.1. This port is used for
unsecure HTTP Internet communication between the
web browser’s UI and the target Master.
80 (TCP)
HTTPS/SSL
This port is used by a web browser to securely
communicate between the web server UI and the
target Master.
443 (TCP)
ICSP
Peer-to-peer protocol used for both Master-to-Master
and Master-to-device communications.
1319 (UDP/TCP)
integration!
Solutions
This feature on the Master uses, by default, port
10500 for the XML based communication protocol.
This port is connected to by the client web browser’s
JVM when integration! Solutions control pages are
retrieved from the on-board Master’s web server.
10500 (TCP)
Note: While the NI-700 is capable of receiving 8 and 9 bit characters, it cannot receive
7 bit, 1 stop bit data from a serial device (ex: 9600,N,7,1).
Connections and Wiring
FIG. 2 shows the layout of the connectors and components located on the rear of the
NI-700 NetLinx Integrated Controller.
Ethernet
RS-232/422/485 (Ports 1 & 2)
PORT 2
PORT 1
ETHERNET
10/100
I/O
IR RX
IR
AXP
1
AXM
2
SPD
12VDC
PWR
3
GND
4
GND
PWR
AUX
GND
IR IN
+12V
L/A
AXlink
PWR
Note: DIP switch 1 activates/deactivates the Program Run Disable Mode. DIP
Switches 2,3, and 4 must remain OFF at all times.
Baud Rate Settings
Baud Rate
Position 5
Position 6
Position 7
Position 8
9600 bps
OFF
ON
OFF
ON
38,400 bps
(default)
OFF
ON
ON
ON
57,600 bps
ON
OFF
OFF
OFF
115,200 bps
ON
ON
ON
ON
Setting the Configuration (Program Port) DIP Switch
IR RX I/O (Port 4)
IR/Serial
(Port 5)
(Port 3)
AXLink
port
Rear
PWR
AXLink LED
(green)
1.
2.
3.
FIG. 2 NI-700 rear connectors and components
Preparing the NI-700 for Serial Communication
Wiring a Power Connection
1.
Use a 12 VDC-compliant power supply to provide power to the NI-700 through the
rear 2-pin 3.5 mm mini-Phoenix connector (FIG. 2). Use the previous power
requirements information to determine the power draw.
The incoming PWR and GND cable from the power supply must be connected to
their corresponding locations within the PWR connector. Refer to the NetLinx
Integrated Controllers Instruction Manual for more detailed wiring connection
information.
2.
3.
4.
RS-232/422/485 Wiring Connector Information
5.
FIG. 3 shows the pinout and wiring specification information for the rear
RS-232/RS-422/RS-485 (DB9) Device Ports. These ports support most standard
RS-232 communication protocols for data transmission (NI-700 uses Ports 1 & 2).
6.
DB9 Serial Port pinouts (male connector)
9
8
5
4
3
2
1
7
6
Disconnect the power supply from the rear 2-pin PWR (green) connector.
Set DIP switch positions according to the information listed in the previous
Baud Rate Settings table.
Reapply power to the unit.
RS-232
RS-422
Pin 1: RX Pin 4: TX +
Pin 5: GND
Pin 6: RX +
Pin 9: TX -
Pin 2: RX signal
Pin 3: TX signal
Pin 5: GND
Pin 7: RTS
Pin 8: CTS
RS-485
Pin 1: A (strap to 9)
Pin 4: B (strap to 6)
Pin 5: GND
Pin 6: B (strap to 4)
Pin 9: A (strap to 1)
Male
FIG. 3 RS-232/422/485 DB9 (male) connector pinouts
WARNING: When wiring the 422/485 connections, do NOT use pre-made 9-wire
cable or connect the wire in the cable to any connection that will not be used by the
DB9 serial port. Only use wiring that connects the needed pins.
7.
8.
9.
10.
11.
12.
13.
14.
Ethernet 10/100 Base-T Connector
A standard CAT5 Ethernet cable provides 10/100 network connectivity between the
Integrated Controller and the network (FIG. 4).
L/A - Link/Activity LED lights
(green) when the Ethernet
cables are connected and
terminated correctly.
ETHERNET
10/100
L/A
SPD
SPD - Speed LED lights (yellow) when
the connection speed is 100 Mbps
and turns Off when the speed
is 10 Mbps.
Configuring the NI-700 for Ethernet Communication
Before continuing, complete the COM port steps above.
1.
2.
3.
•
FIG. 4 Layout of Ethernet LEDs
•
Note: On NetLinx Masters (such as those aboard the NI-700), from within the Telnet
or Terminal applications; you can send the SET ETHERNET MODE command to
assign the speed of your Ethernet connection.
Sample NI-700 command:
Launch NetLinx Studio 2.x (default location is Start > Programs > AMX
Control Disc > NetLinx Studio 2 > NetLinx Studio 2).
Select Settings > Master Communication Settings, from the Main menu, to
open the Master Communication Settings dialog box.
Click the Communications Settings button to open the Communications
Settings dialog.
Click the NetLinx Master radio button (from the Platform Selection section) to
indicate you are working with a NetLinx Master.
Click the Serial radio button (from the Transport Connection Option section) to
indicate you are connecting to the Master via a COM port.
Click the Edit Settings button (on the Communications Settings dialog) to
open the Serial Settings dialog and set the COM port parameters (used to
communicate to the NetLinx Master).
Click the OK button three times to return to the main application.
Right-click the entry in the Online Tree tab and select Refresh System.
Assign a System Value by using Diagnostics > Device Addressing from the
Main menu.
Enable the Change System selection by clicking on it and then enter the
current and new System values.
Click the Change Device/System Number button and when finished click
Done.
Select Tools > Reboot the Master Controller to access the Reboot the
Master dialog, then click Reboot to restart the Master and incorporate any
changes.
Once the dialog replies with "Reboot of system complete", click Done and then
click the OnLine Tree tab in the Workspace window to view the devices on the
System.The default System value is one.
Right-click on the Empty Device Tree/System entry and select Refresh
System to re-populate the list.
4.
SET ETHERNET MODE AUTO
The NI-700 only allows you to set the Ethernet mode to AUTO negotiate the
Ethernet connection speed. Using any of the other connection modes (10 Half/
Full or 100 Half/Full) results in an error message.
5.
Program Port Baud Rate Settings
6.
Connect an Ethernet cable to the unit’s rear Ethernet connector.
Select Diagnostics > Network Address from the Main menu and enter the
System, Device (0 for a Master), and Host Name information.
To configure the Address:
Use a DHCP Address by selecting the Use DHCP radio button, then click the
GET IP button (to obtain a DHCP Address from the DHCP Server), click the
SET IP Information button (to retain the new address), and then finish the process by clicking the Reboot Master > OK buttons.
Use a Static IP Address by selecting the Specify IP Address radio button,
enter the IP parameters into the available fields, then click the SET IP Information button (to retain the pre-reserved IP Address to the Master), and then click
the Reboot Master > OK buttons to finish the process.
Repeat steps 1 - 5 from the previous section but rather than selecting the
Serial option, choose TCP/IP and edit the settings to match the IP Address
you are using (whether Static or IP).
Click on the Authentication Required radio box (if the Master is secured) and
press the User Name and Password button to enter a valid username and
password being used by the secured Master.
Click the OK button three times to return to the main application.
The Configuration DIP switch is located on the front panel. Use this DIP switch to set
the baud rate for the Program Port, according to the settings shown in the following
table. Make sure the baud rate you set matches the baud rate on your PC's NetLinx
COM Settings before programming the unit.
By default, the baud rate is set to 38,400 (bps).
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/09
©2009 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2105-70
REV: B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement