advertisement
Ethernet Switch
ESUL8P-PC2
User Manual
Ethernet Switch User Manual
TABLE OF CONTENTS
1 OVERVIEW ................................................................................. 3
ESUL8P-PC2 ....................................................................................... 3
2 INSTALLATION ............................................................................. 5
Physical Connections ........................................................................... 6
DIN Rail Mount ................................................................................... 7
3 TROUBLESHOOTING .................................................................... 11
4 SYSTEM EXAMPLE ....................................................................... 12
5 DIMENSIONS (MM) ....................................................................... 12
6 WARRANTY .............................................................................. 13
7 INSTRUCTION OF DISASSEMBLY ...................................................... 14
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 2 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
1 Overview
1.1 Introduction
This manual covers the ESUL8P-PC2 series. KBC Networks’ ESUL8P-PC2 products are high performance, unmanaged, ten port industrial PoE Ethernet switches designed for use in a wide range of operating temperatures in nonenvironmentally conditioned, industrial applications. The units have redundant power supply terminals and an alarm output. All copper ports are automatically configured and the plug-and-play design provides ease and speed of installation.
1.1.1 ESUL8P-PC2
The ESUL8P-PC2 provides connectivity for up to eight, 10/100 RJ45 twisted pair copper ports which are capable of simultaneously supplying IEEE802.3af PoE and two gigabit combo ports. Each of the eight, 10/100 RJ45 ports supports a self-adaptive function allowing it to be configured to 10Base-T or 100Base-TX, full or half duplex operation mode. The two combo ports offer a 10/100/1000
RJ45 interface or a 100/1000 SFP module slot. It is available as either DIN rail or wall-mount configurations.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 3 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
1.2 Technical Specification
Switching
Mode
Switching rate
Backplane switching bandwidth
Mac address table
Ports
Combo
Physical port
RJ45 port
Copper
Physical port
RJ45 port
Standard
Transmission distance
PoE
Physical port
Standard
Power supplied (per port)
Electromagnetic compatibility
Interference
Immunity
Power
Input voltage
Power consumption
Power supply
Environmental
Operating temperature
Storage temperature
Relative humidity
Mean Time Between Failure
Mechanical
Dimensions (W x H x D)
Protection class rating
Weight
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 4 of 15
ESUL8P-PC2
Store-and-forward
14,881pps, 148,810pps or 1,488,100pps
5.6Gbps
8k
2 x shielded RJ45, 2 x 100/1000 SFP
10BASE-T/100BASE-TX/1000BASE-T
8 x shielded RJ45
10BASE-T/100Base-TX
Auto-negotiation
IEEE 802.3
<100m
8 x shielded RJ45
IEEE 802.3af
15.4W @ +48Vdc
EN55022 Class A
IEC61000-6-2
48Vdc
16.8W (no PoE)
123W ( full load PoE)
Supplied separately
-40°C - +74°C / -40°F - +165°F
-40°C - +74°C / -40°F - +165°F
5% - 95%, Non-condensing
>300,000 hours
72mm x 152mm x 105mm
2.83” x 5.98” x 4.13”
IP30
907g
2.0lb www.kbcnetworks.com
Ethernet Switch User Manual
2 Installation
2.1 Package Contents
Ethernet switch fitted with DIN rail mount.
2 x Wall-mount brackets with screws
Pluggable terminal block
Quick Start Guide
Note: A 48Vdc PSU is required but supplied separately.
Please contact you dealer or distributor if a part is missing or damaged.
2.2 Configurations
Products are available in either DIN rail or wall-mount packages, with the following configurations:
Product Type
ESUL8P-PC2
DIN Rail
Wall-mount
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 5 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
2.2.1 Physical Connections
Top View
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 6 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
2.3
Installation Method
2.3.1 DIN Rail Mount
Remove all packaging material.
Attach the device to a DIN rail.
Attach copper cables as required.
Insert the male power block (attached to the supplied in-line PSU) to the female power socket on the device and tighten the terminal locking screws using a flathead screw driver.
See Section 2.7 for LED status.
2.3.2 Wall-mount
Remove all packaging material.
Unscrew the DIN rail mounting plate from the switch taking special care to retain the 3 screws using a Phillips No.1 or No.2 screwdriver.
Attach the supplied wall mount plates to the switch using the screws that have just been removed from the DIN rail mounting plate with a Phillips
No.1 or No.2 screwdriver.
Position the unit on the required, flat surface and secure with screws via the mounting plate holes. Screws are not provided.
Attach copper cables as required.
Insert the male power block (attached to the supplied in-line PSU) to the female power socket on the device and tighten the terminal locking screws using a flathead screw driver.
See Section 2.7 for LED status.
2.4 Ethernet RJ45 Connections
Each of the eight fixed RJ45 ports (P1 to P8) are adaptive and support auto MDI/MDI-X connection. They can be connected by straight through or cross-over cables to terminal devices, servers, hubs or other switches. Each switch supports IEEE802.3x so the optimum transmission mode (either half-duplex or full-duplex) and data rate (either
10Mbps or 100Mbps) will be selected automatically.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 7 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
2.5 Combo ports
The SFP ports can be configured as 100BASE-FX/BX or 1000BASE-SX/LX/BX/ZX in any permutation.
The RJ45 ports are IEEE802.3ab compliant, 10/100/1000.
Note: If the SFP port is being used then the corresponding RJ45 port is automatically disabled and vice versa.
2.6 Power Connections
A 6 pin, power terminal block should be used to connect the power cable to the unit.
1 2 3 4 5 6
VV+ VV+
Figure 2.1 Power connections
Contact number
1
2
3
Connections
PWR2: -
PWR2: +
Fault alarm contact
4
5
6
Fault alarm contact
PWR1: -
PWR1: +
Note: If only using one power source, connect pin 1 to pin 5 and pin 2 to pin 6 otherwise the Power Fault Alarm will be lit.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 8 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
2.7 Fault Alarm Contacts
The fault alarm contacts are in the middle of the 6 pin, screw block terminal on pins 3 &
4. An open circuit will occur if a power failure is detected.
1 2 3 4
P-Fail
5 6
24Vdc, 1A resistance
Load
External power
Figure 2.2 Fault Alarm Contacts
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 9 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
2.8 LED Status
LED
PWR1
PWR2
P-Fail
PoE 1-8
Status
ON
OFF
ON
OFF
ON
OFF
Description
Power is supplied to the unit
No power to the unit
Power is supplied to the unit
No power to the unit
Power to PWR1 or PWR2 has failed
Power is functioning to both or none of the power inputs
ON The port is supplying power to the powered device
OFF
There is no powered device attached or the power to the device has failed
Ethernet RJ45 Ports P1 - P8 Status LED
Each RJ45 Ethernet port has two indicators, a yellow lamp and a green lamp. The yellow lamp indicates port speed, and the green lamp indicates port link state.
ON Full duplex link
10/100
(Yellow)
FLASH Collisions are occurring
LINK/ACT
(Green)
OFF
ON
FLASH
OFF
Half duplex link or no connection
Effective network connection has been established for the port
Data traffic is passing through the port
No effective network connection has been established for the port
Ethernet RJ45 Ports P9 & P10 Status LED
Each RJ45 Ethernet port has two green indicators, an upper and lower. The upper one indicates the state of the port link and the lower one indicates port link speed.
Lower
LED
ON
OFF
Port operating at 1000M
Upper
LED
ON
FLASH
Port not operating at 1000M or no connection
Effective network connection has been established for the port
Data traffic is passing through the port
OFF
ON
No effective network connection has been established for the port
SFP port link established
Link
/Active
FLASH Active data flow
OFF No connection to the network
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 10 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
3 Troubleshooting
3.1 Self-testing
When the device is powered on, all LEDs on the front panel will flash twice, indicating that the ports are running normally and the Power (PWR1/2) indicator lights will be illuminated if power is connected to the respective input.
If problems are encountered when using this Ethernet switch please check the following:
Verify that the correct power supply unit is being used; this unit requires a
48Vdc supply.
Ensure that the correct cables are being used to construct your network: o Unshielded Twisted Pair or Shielded Twisted Pair for RJ45 connections o 100Ω Cat 3 cable or above for 10Mbps connections o 100Ω Cat 5 cable or above for 100Mbps connections o 100Ω Cat 5e cable or above for 1000Mbps connections o Twisted pair connection must not exceed 100m (328 feet)
See section 2.7 for LED status indicators.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 11 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
4 System Example
5 Dimensions
Figure 4.1 ESUL8P-PC2 Typical System Application
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 12 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
6 Warranty
6.1 Warranty Information
KBC extends the following LIMITED WARRANTY to the original owner/purchaser of this product as follows:
-
Five years from the date of initial sale for Ethernet switches.
-
Two years from the date of initial sale for all wireless and other network products.
-
Five years from the date of initial sale for all fiber products.
1) If, within the specified warranty period, this product, or any part or portion thereof, shall prove upon examination by KBC, to be defective in material or workmanship,
KBC will repair or replace such part or portion at KBC’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty. The buyer shall be responsible for all shipping and transportation of the product to KBC for any performance under this warranty.
2) Conditions and Exceptions: a) Any accident to this product, any misuse or abuse, alternation, use in modified form, or any attempt to repair this product shall void this warranty. These conditions to the warranty include, but are not limited to, incorrect power connections, physical damage due to mechanical shock, exposure to moisture, and circuit modification. b) SHOULD THIS PRODUCT PROVE DEFECTIVE FOLLOWING PURCHASE, THE BUYER,
NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER, ASSUMES THE ENTIRE
COST OF ALL SERVICING OR REPAIR, EXCEPT AS OTHERWISE PROVIDED BY THE
TERMS OF THIS WARRANTY. c) FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY ON THIS PRODUCT, THE
BUYER IS LIMITED TO THE FOLLOWING DAMAGES. (1) THE COST OF LABOR TO
REPAIR OR REPLACE DEFECTIVE PARTS OR PORTIONS OF THIS PRODUCT, AND
(2) THE COST OF THE REPAIRED OR REPLACE PARTS OR PORTIONS OF THIS
PRODUCT. d) NO OTHER EXPRESSED OR IMPLIED WARRANTIES HAVE BEEN MADE OR WILL BE
MADE ON BEHALF OF KBC WITH RESPECT TO THE SALE, REPAIR, INSTALLATION,
OPERATION, OR REPLACEMENT OF THIS PRODUCT. KBC DISCLAIMS ANY
IMPLIED WARRANTY OF MERCHANTABILITY OF THIS PRODUCT OR ITS FITNESS
FOR ANY PURPOSE, AND THE BUYER AGREES THAT THIS PRODUCT IS SOLD “AS
IS” AND THAT THE ENTIRE RISK OF QUALITY AND PERFORMANCE OF THIS
PRODUCT IS WITH THE BUYER, EXCEPT AS OTHERWISE PROVIDED BY THE
TERMS OF THIS WARRANTY. e) Some states/jurisdictions do not allow exclusions or limitations of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. f) If you do not wish to be bound by any of the provisions in this warranty, please return the product(s) immediately.
3) Contact your dealer regarding return authorizations for out of warranty repairs and any further product information.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 13 of 15 www.kbcnetworks.com
Ethernet Switch User Manual
6.2 Class A ITE
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
6.3 FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful Interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense.
7 Instruction of Disassembly
Instruction of Disassembly of KBC Product
(For EU Directive 2002/95/EEC-WEEE)
Tools required:
No. 1 Phillips screwdriver
No. 2 Phillips screwdriver
Steps for disassembly:
1. Remove tightening screws of box cover (8 screws).
2. Remove cover plate.
3. Remove tightening screws for printed circuit board (PCB).
4. Take out all PCBs.
Notice: When a product reaches the end of its life – return to KBC.
Manual-ESUL8P-PC2_Series_HW-Rev1201
Copyright © KBC Networks Ltd. Page 14 of 15 www.kbcnetworks.com
data delivered
KBC Networks
25691 Atlantic Ocean Drive
Suite 3B
Lake Forest, CA 92630
U.S.A
Americas
Phone:
Fax:
1-949-297-4930
1-949-297-4933
KBC Networks Ltd., EMEA
KBC Networks Ltd.
Barham Court
Teston, Maidstone
Kent, ME18 5BZ
United Kingdom
Phone:
Fax:
Email:
Web:
+44(0)1622 618787
+44(0)20 7100 8147 [email protected]
www.kbcnetworks.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project