JBL CINEMA SB450 Owner's Manual

JBL CINEMA SB450
OWNER’S MANUAL
TABLE OF CONTENTS
INTRODUCTION
3
INCLUDED ITEMS
3
TOP PANEL CONTROLS AND REMOTE CONTROL
3
SOUNDBAR REAR PANEL CONNECTIONS AND CONTROLS
4
SUBWOOFER REAR PANEL CONNECTIONS AND CONTROLS
5
SOUNDBAR PLACEMENT
5
PLACING THE SOUNDBAR ON A TABLE
5
WALL-MOUNTING THE SOUNDBAR
5
SUBWOOFER PLACEMENT
6
CONNECTIONS
6
SOUNDBAR AUDIO/VIDEO CONNECTIONS
6
POWER CONNECTIONS
7
USING YOUR SOUNDBAR SYSTEM
TURNING THE SOUNDBAR ON AND OFF
7
TURNING THE SUBWOOFER ON AND OFF
7
Pairing the Units for Wireless Operation
7
SWITCHING SOURCES
7
ADJUSTING THE SYSTEM’S VOLUME
7
MUTING THE SYSTEM
8
USING BLUETOOTH
8
USING JBL SOUNDSHIFT™
8
USING JBL CONNECT
8
USING AUDIO FEEDBACK
9
USING VIRTUAL SURROUND
9
USING HARMAN VOLUME
9
ADJUSTING THE BASS
SUBWOOFER LEVEL CONTROL
2
7
9
9
SUBWOOFER CROSSOVER CONTROL
10
SUBWOOFER PHASE SWITCH
10
USING YOUR OWN TV REMOTE (TV REMOTE CONTROL LEARNING)
10
RESETING THE SOUNDBAR
10
TROUBLESHOOTING
11
English
INTRODUCTION
Wall Mount Bracket
Thank you for purchasing the JBL Cinema SB450. The JBL
Cinema SB450 is designed to bring an extraordinary sound
experience to your home entertainment system. We urge you to
take a few minutes to read through this manual, which describes
the product and includes step-by-step instructions to help you set
up and get started.
x1
Quick Start Guide
x1
TOP PANEL CONTROLS AND REMOTE
CONTROL
CONTACT US: If you have any questions about JBL
Cinema SB450, its installation or its operation, please
contact your retailer or custom installer, or visit our
website at: www.JBL.com.
INCLUDED ITEMS
Power
Source
Virtual Surround
Wireless Subwoofer
HDMI 1/2/3
Aux
HDMI TV
Optical
3
1
5
2
4
6
10
9
Remote Control
Bluetooth
JBL Soundshift
SOURCE LED BEHAVIOR
x1
x1
JBL Connect
Volume Volume
Down
Up
Soundbar
8
7
11
12
13
16
15
14
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
Power
Bluetooth
JBL Connect
JBL Soundshift
Audio Feedback
Volume +/Mute
Bass Volume +/HDMI 1 Input
HDMI 2 Input
HDMI 3 Input
HDMI TV Input
Optical Input
Aux Input
Virtual Surround
Harman Volume
Note: Before using the remote control, remove the plastic tab protecting the battery at
the bottom of the remote control.
x1
Optical Cable (5ft, 1500mm)
x1
HDMI Cable (3ft, 1000mm)
Power: Press this button to turn the system on when the
soundbar is in Standby mode,(The Power indicator will turn white.)
To put the system in Standby mode, press the Power button while
the system is on. (The Power indicator will turn amber.)
NOTE: The soundbar will automatically go into
Standby mode after 10 minutes of inactivity. For more
information, see the “Turning the Soundbar On and Off”
section.
Source: Press this top-panel button to cycle between the sources
in the following order: HDMI 1, HDMI 2, HDMI 3, HDMI TV, Aux
and Optical. The active Source Indicator LED will illuminate. The
remote has an individual selector button for each source.
x1
(2) Power Cables (5ft, 1500mm)
x1
x1
Virtual Surround: Press this button to turn the soundbar’s
HARMAN Display Surround processing on and off. The Virtual
Surround button indicator turns white when HARMAN Display
Surround is active. See the “Virtual Surround” section for more
information.
Volume Buttons: Press the “+” button to increase the volume;
press the “–” button to decrease the volume.
www.jbl.com
3
Bass Level Control (remote control only): Press these
buttons to adjust the overall level of the subwoofer to your
preference.
Harman Volume (remote control only): Press this button to
activate Harman Volume. This feature helps to maintain the volume
level constant and minimizes big variations in volume level when
listening to music or watching television. See the “Using Harman
Volume” section for more information.
Optical: If your TV, disc player or cable/satellite tuner has an
optical digital output, use the included optical cable to connect it
here.
Aux: Use a 3.5mm audio cable to connect the stereo analog
outputs of your TV, disc player or cable/satellite tuner here.
Audio Feedback (remote control only): Press this button to
activate Audio Feedback. This feature provides audible tones to
indicate when certain functions are active. See the “Using Audio
Feedback section” for more information.
HDMI 1/2/3: HDMI connections transmit digital audio and video
signals between devices. If you have source devices with HDMI
connectors, using them will provide the best possible audio and
video performance quality.
Mute (remote control only): Press the Mute button to mute
the system. (The top-panel Power LED indicator will blink white.)
While the system is muted, press the Mute button again or either
Volume button to restore the sound.
NOTE: Pressing both of the soundbar’s top-panel Volume
buttons at the same time while the system is on will
mute the system. Pressing either Volume button while
the system is muted will restore the sound.
HDMI TV: If your TV has an HDMI input, use the provided
HDMI cable to connect it to the soundbar’s HDMI ARC TV Out
connector. The soundbar will pass video from source devices
connected to its HDMI Input connectors. If your TV is equipped
with the HDMI Audio Return Channel (ARC) Function, you
can feed its sound to the soundbar via the HDMI ARC TV Out
connection, and it will not require additional audio connections to
the soundbar. The ARC signal is active when the HDMI TV source
is selected.)
Bluetooth: Press this button to play the audio stream from a
paired Bluetooth device through the soundbar. (The Bluetooth
Source Indicator LED will illuminate when a paired Bluetooth
device is the active source.) Press and hold this button to force
the soundbar into the Bluetooth pairing mode. See the “Using
Bluetooth” Section for more information.
JBL Connect: Press this button to engage JBL Connect pairing
mode. JBL Connect creates a Bluetooth wireless connection
with other compatible JBL Connect products. See “Using JBL
Connect” section for more information.
JBL SoundShift®: Press this button to engage JBL SoundShift.
JBL SoundShift allows you to instantly switch between sound from
your TV and sound from your phone or tablet. See the “Using JBL
SoundShift” section for more information.
SOUNDBAR REAR PANEL CONNECTIONS AND
CONTROLS
7
6
2
4
3
9
1)
2)
3)
4)
5)
4
Power Input: Connect the included power cord here. See the
“Power Connections” section for more information.
USB (Software updates only)
Power In
Aux IN
Optical IN
HDMI 1
1
6)
7)
8)
9)
10)
2
1
5
3
TV(ARC)
8
10
2
1
3
TV(ARC)
HDMI 2
HDMI 3
HDMI TV
Subwoofer pairing button
Wall Mount / Table Mount EQ switch
Subwoofer Pairing Button: Press the Pairing button to
initiate wireless pairing between the soundbar and the wireless
subwoofer. See the “Pairing the Units for Wireless Operation”
section for more information.
Wall-Mount/Table-Mount EQ Switch: Use this switch to
adjust the soundbar’s equalization (EQ) for either wall or table
mounting. If you’re mounting the soundbar on a wall with the
included wall-mount bracket, set the EQ switch to the “Wall”
position for the most natural-sounding bass performance. If you
are placing the soundbar on a table, set the EQ switch to the
“Table” position for the most natural-sounding bass performance.
Software: The USB connection is for manual software updates
only. If a new software update is released, JBL will notify you if
your product is registered at www.JBL.com
IMPORTANT: Do not connect the power cord to an
AC outlet until you have made and verified all other
connections.
English
SUBWOOFER REAR PANEL CONNECTIONS
AND CONTROLS
2
SOUNDBAR PLACEMENT
PLACING THE SOUNDBAR ON A TABLE
If your TV is placed on a table, you can place the soundbar on
the table directly in front of the TV stand, centered with the TV
screen. As long as the surface of the table is flat, the soundbar will
rest on its metal feet. Set the soundbar’s EQ switch in the “Table”
position. See Soundbar Rear-Panel Controls and Connections.
5
1
4
3
1) Power
2) Wireless Pairing Button
3) Crossover
4) Power Input AC
5) Phase
Attention: Your JBL CINEMA SB450 comes with subwoofer
already paired from the factory, please refer to the subwoofer
connection section of this owner’s manual only if you are
experiencing no audio output from your subwoofer after
connecting it to the power.
Wireless Pairing: Press this button to initiate wireless pairing
between the subwoofer and the soundbar. The LED lights
white continuously when the subwoofer is on and linked to the
soundbar. The LED slowly flashes white when the subwoofer is
on and the wireless link is not established between the subwoofer
and the soundbar. The LED rapidly flashes white during the
wireless pairing process.
WALL-MOUNTING THE SOUNDBAR
If your TV is attached to a wall, you can use the included wallmount bracket to mount the soundbar on the wall directly below
the TV screen.
1.
Determine the location for the soundbar on the wall. Make
sure that the top of the soundbar will not block your view of
the TV screen when it is mounted on the wall.
2.
Hold the bracket against the wall as a template and mark the
locations of the soundbar wall-mount bracket holes on the
wall. The three holes should be evenly spaced 7-1/16” (18cm)
apart, and the bracket slots are designed to accept 4mm
screws. Make sure that the holes are at the same height. See
the illustration below.
Phase Control: This switch determines whether the subwoofer
driver’s piston-like action moves in and out in phase with the
speakers in the soundbar. If the subwoofer were to play out of
phase with the soundbar speakers, some of the sound waves
produced by the subwoofer or soundbar could be canceled,
reducing bass performance and sonic impact. This phenomenon
depends in part on the relative placement of the speakers in
the room. See the “Subwoofer Phase Switch” section for more
information.
Crossover: This knob adjusts the subwoofer’s cutoff between
40Hz and 200Hz.The higher you set the Cutoff control, the higher
in frequency the subwoofer will operate and the more its bass will
“overlap” that of the soundbar. This adjustment helps achieve a
smooth transition of bass frequencies between the subwoofer
and the soundbar for a variety of different rooms and subwoofer
locations. See the “Subwoofer Crossover Control” section for
more information.
Mark Three Bracket Hole Locations
7-1/16" (18cm) Apart
3.
Making sure that the bracket’s flat side is against the wall,
attach the wall-mount bracket to the wall at the locations
you marked, using hardware that is appropriate for the wall’s
construction and materials. Note that the soundbar weighs
7.5 lb (3.4kg). Be sure to use hardware that can support this
weight.
Power Cord Connector Connect the included power cord here
and into an active, unswitched AC outlet. See Power Connections
for more information.
IMPORTANT: Do not connect the power cord to an
AC outlet until you have made and verified all other
connections.
After reading the Connections section, connect all cables to the
soundbar.
www.jbl.com
5
IMPORTANT: Do not plug the soundbar’s power cord into
an AC outlet at this time.
4.
Set the soundbar’s EQ switch in the “Wall” position.
5.
Attach the soundbar to the bracket by sliding the bracket’s
upper tabs into the slots on the back of the soundbar. The
soundbar’s slots allow you to adjust the soundbar’s angle on
the wall to ensure that it is level.
TV Out connection. The soundbar will pass video from source
devices to the TV. If your TV is equipped with the HDMI Audio
Return Channel (ARC) Function, you can feed its sound to the
soundbar via the HDMI ARC TV Out connection, and it will not
require additional audio connections to the soundbar. The ARC
signal is active when the HDMI TV source is selected.
Insert Tabs on Bracket
into Grooves in Soundbar
6.
After reading the Connections section, connect all cables to
the soundbar.
To
HDMI In
1/2/3
To
HDMI ARC
TV Out
SUBWOOFER PLACEMENT
HDMI-Equipped
Source Device
HDMI-Equipped
TV
1
2
HDMI In 1/2/3: If any of your source devices have HDMI
connectors, connect them to the soundbar’s HDMI In 1/2/3
connectors for the best possible video and audio performance
quality. Since the HDMI cable carries both digital video and digital
audio signals, you do not have to make any additional audio
connections for source devices you connect via HDMI connectors.
3
The performance of a subwoofer is directly related to its placement
in the listening room and its physical position relative to the other
speakers in the system. For example, placing it in a corner (1)
generally will maximize the amount of bass in the room. In many
rooms, placing the subwoofer along the same plane as the
soundbar (2) can produce the best integration between the sound
of the subwoofer and that of the soundbar. In some rooms, the
best performance could even result from placing the subwoofer
behind the listening position (3). We strongly recommend that you
experiment with placement before choosing a final location for
your subwoofer.
CONNECTIONS
SOUNDBAR AUDIO/VIDEO CONNECTIONS
HDMI ARC TV Out: If your TV has an HDMI input, use the
included HDMI cable to connect it to the soundbar’s HDMI ARC
6
NOTE: The JBL CINEMA SB450 supports HDCP 2.2
on all its HDMI inputs and output, meaning that you
can connect directly any 4K ultra HD source to your
soundbar. Please refer to your television owner’s manual
to ensure that it is also supports HDCP 2.2 as otherwise
any 4K content with HDCP 2.2 copy protected content
will automatically be downscaled to full HD on your
television even if it is 4k compatible.
Aux In and Optical In connections: If your TV and source
devices do not have HDMI connections, you can use the supplied
audio cable and optical cable to connect your TV and one source
device to the soundbar’s Aux In and Optical In connectors,
respectively.
NOTE: The Optical Input does not support all digital
audio and surround sound formats. If the optical input
receives an unsupported audio format, there may be
a sound dropout. The HDMI Input will automatically
detect and resolve unsupported audio formats. If you
experience sound dropouts with the optical connection,
it is recommended to change the audio output format on
the source device to PCM or use an HDMI connection
from your source to the soundbar.
English
POWER CONNECTIONS
After verifying that all of the source connections have been made
properly, plug the supplied power cords into the soundbar’s and
subwoofer’s Power Cord connectors, and plug the other ends into
active, unswitched AC outlets. Do NOT plug this cords into the
accessory outlet found on some audio components.
To
Unswitched
AC Outlet
Power
Power
Cord
Cord
(supplied) (supplied)
To
Unswitched
AC Outlet
USING YOUR SOUNDBAR SYSTEM
TURNING THE SOUNDBAR ON AND OFF
Press the Power button on either the soundbar or the remote
control to turn the soundbar on. To put the soundbar in the Standby
mode, press either Power button while the soundbar is on.
If you have manually put the soundbar into the Standby mode by
pressing the Power button, you can turn it back on by:
1.
2.
Pressing the Power button again
Streaming music from a connected Bluetooth device
Soundbar
Pairing Switch
NOTE: The maximum wireless operating distance
between the soundbar and subwoofer is approximately
30 feet (10m).
SWITCHING SOURCES
You may select any of the devices that are connected to the
soundbar by pressing the corresponding button on the JBL
Cinema SB450 remote control or pressing the source button on
the top button panel. The active source’s Source Indicator LED will
illuminate.
If you have connected devices directly to your TV’s input
connections AND you have connected the soundbar to your TV’s
HDMI ARC input, then audio will flow from the TV to the soundbar.
1.
The soundbar will automatically go into the Standby mode after 10
minutes of inactivity. If the soundbar has automatically gone into
the Standby mode, it will automatically turn itself on again when it
receives an audio signal from the last detected connection.
NOTE: You can control the soundbar with your own TV
remote control. See the “Using Your Own TV Remote (TV
Remote Learning)” section for more information.
TURNING THE SUBWOOFER ON AND OFF
Set the subwoofer’s Power switch to the “On” position. Once
the subwoofer and soundbar have been paired (see Pairing the
Units for Wireless Operation, below) the subwoofer will turn on
when the soundbar turns on and will remain on for approximately
30 seconds after the soundbar enters the Standby mode, or
for approximately 10 minutes after the audio signal ceases. If
you will be away from home for an extended period of time, or if
you will not be using the system for an extended period, set the
subwoofer’s Power switch to the “Off” position.
Pairing the Units for Wireless Operation
Subwoofer
Pairing Switch
2.
Press the HDMI TV button on the JBL SB450 remote control
to select audio from your TV.
Use your TV remote control to select the corresponding input
source device—this may be with an “INPUT” or “SOURCE”
button. Refer to your TV settings and operation.
ADJUSTING THE SYSTEM’S VOLUME
Press the soundbar’s or remote’s Volume + and – buttons to raise
and lower the system’s volume one step at a time. Hold down the
buttons to continuously raise or lower the volume. For the best
sound, we recommend turning your TV’s built-in speakers off.
Consult your TV’s owner’s manual to find out how to do this.
Note: You can control the soundbar with your own TV remote
control. See the “Using Your Own TV Remote (TV Remote
Learning)” section for more information.
Volume Buttons
The JBL Cinema SB450 soundbar and wireless subwoofer are
automatically “paired” with each other. If the system does not
connect right away, press the Wireless Pairing buttons on both
units within 30 seconds of each other. The units will communicate
with each other and operate at the same frequency.
www.jbl.com
7
time without reaching for the remote control to switch between the
two devices.
MUTING THE SYSTEM
Momentarily press both of the soundbar’s top-panel volume
buttons at the same time, or press the remote control’s Mute
button to mute the system (The Power LED flashes.) Momentarily
press either of the soundbar’s Volume buttons or press the
remote’s Mute button again to un-mute the system.
Mute
Button
OR
LED BEHAVIOR
Both Volume Buttons
Soundshift is off
Soundshift is on
USING BLUETOOTH
Bluetooth is a wireless connection that will help you to stream any
music from your mobile device to your soundbar. You can pair up
to 3 Bluetooth devices at the same time.
or
1.
JBL SB450
2.
LED BEHAVIOR
Bluetooth Pairing
Bluetooth Paired
1.
2.
3.
4.
Press and hold the Bluetooth button for 3 seconds to enter
pairing mode (the button LED will quickly flash blue).
Open your Bluetooth settings on your mobile device, then
locate and select JBL CINEMA SB450.
Test the connection by streaming music from your device to
your JBL Cinema SB450.
To add an additional Bluetooth device (up to 3), repeat steps
1 & 2.
3.
4.
5.
Confirm that you have paired at least one Bluetooth device to
the soundbar (See “Using Bluetooth” section).
Press the JBL Soundshift button on the Remote Control
or Top-panel buttons until the LED turns BLUE. This color
indicates that JBL SoundShift is ON.
Play sound from any source through your soundbar in a
normal manner.
Press PLAY on your mobile device to stream music. You will
hear the Bluetooth audio “break in” over your TV sound.
Press PAUSE on your mobile device. You will hear the audio
automatically switch back to your TV.
USING JBL CONNECT
JBL Connect lets you wirelessly daisy chain two speakers. JBL
Connect requires an additional compatible speaker like JBL Flip 3,
JBL Xtreme, or JBL Pulse 2. For more information, please visit our
website at www.jbl.com
NOTE: If you have more than one Bluetooth device
paired at one time, one device may interrupt/override
another device simply by pressing “PLAY”.
USING JBL SOUNDSHIFT™
1.
JBL SoundShift is a new technology that allows you to seamlessly
switch between your TV and your wireless Bluetooth device. This
helps to you watch TV and use your Bluetooth device at the same
8
2.
Confirm that you have paired at least one Bluetooth device to
the soundbar
Press the JBL Connect button on the remote control or the
top-panel button (LED will blink white).
English
3.
4.
5.
6.
Press the JBL Connect button on your other JBL speaker.
Once the soundbar and secondary JBL speaker are
connected, the LED will turn solid white.
Stream music from your wireless device. You will hear sound
on both speakers
The volume is synchronized between the two devices—
turning the volume up or down on one device will affect the
other.
To disable JBL Connect, turn off the second device.
Harman Display Surround brings rich virtual surround sound
to your home entertainment experience. Turn Harman Virtual
Surround ON when you are watching movies for a wide, spacious
sound effect.
Press the soundbar’s or remote’s Surround Mode button to
switch the sound between normal stereo and Harman Display
Surround (the Surround Mode indicator lights white). The Harman
Display Surround setting will produce a complete surround-sound
experience for anyone sitting in front of and several feet away from
the soundbar. Although it is particularly effective when watching
movies, you can also try the Harman Display Surround setting for
music.
Surround Buttons
Surround Buttons
USING HARMAN VOLUME
LED BEHAVIOR
Seeking JBL Connect Speaker
Paired with JBL Connect Speaker
NOTE: JBL Connect supports Bluetooth audio streaming
only. Audio from the wired TV input will not stream to
the second JBL device.
USING AUDIO FEEDBACK
Harman Volume reduces major volume differences between soft
and loud in content and maintains a more uniform volume level.
Turn Harman Volume ON when watching TV with commercials or
late-night movies. To turn Harman Volume ON, press the button
on the remote control.
NOTE: Turn Audio Feedback ON with the remote control
to hear an audible indication for Harman Volume ON/OFF
settings
Audio feedback enables audible tones indicate certain product
features. When Audio feedback is ON, you will hear tones for
specific actions on the JBL Cinema SB450:
ADJUSTING THE BASS
1.
2.
3.
4.
5.
6.
Press the Bass Level +/- buttons on the remote control to adjust
the bass level to your preference.
Bluetooth Pairing is ON.
Bluetooth device is connected
JBL Connect paring is ON
JBL Connect device is connected
JBL SoundShift On/Off
Harman Volume On/Off
USING VIRTUAL SURROUND
SUBWOOFER LEVEL CONTROL
Bass Buttons
LED
BEHAVIOR
Virtual Surround ON
Virtual Surround OFF
www.jbl.com
9
SUBWOOFER CROSSOVER CONTROL
The subwoofer’s Crossover control adjusts the subwoofer’s cutoff
between 40Hz and 200Hz. The higher you set the Crossover
control, the higher in frequency the subwoofer will operate and the
more its bass will “overlap” that of the soundbar. This adjustment
helps achieve a smooth transition of bass frequencies between the
subwoofer and the soundbar for a variety of different rooms and
subwoofer locations. To set the Crossover control, listen for the
smoothness of the bass. If the bass seems too strong at certain
frequencies, try a lower Crossover control setting. If the bass
seems too weak at certain frequencies, try a higher Crossover
control setting.
30cm
(12")
Press and Hold Until
Button Flashes Amber
1.
2.
CROSSOVER
SUBWOOFER PHASE SWITCH
This switch determines whether the subwoofer’s piston-like action
moves in and out in phase with the speakers in the soundbar.
If the subwoofer were to play out of phase with the soundbar
speakers, some of the sound waves produced by the soundbar
and subwoofer could be canceled out at some frequencies,
reducing bass performance and sonic impact. This phenomenon
depends in part on the relative placement of the soundbar and
subwoofer in the room. Although there is no absolutely correct
setting for the Phase switch, in most cases it should be left in
the “0°” position. When the subwoofer is properly in phase with
the soundbar speakers, the sound will be clearer and have more
impact. It will make percussive sounds like drums, piano and
plucked strings sound more lifelike. The best way to set the Phase
switch is to listen to music that you are familiar with and adjust the
switch so that drums and other percussive sounds have maximum
impact.
PHASE
USING YOUR OWN TV REMOTE (TV REMOTE
CONTROL LEARNING)
If you are using an HDMI ARC connection to your television, then
your TV remote control will automatically operate the soundbar
for standard commands such as power on/off and volume
control. The JBL CINEMA SB450 supports HDMI CEC and will
interoperate with compatible TV’s (check your TV owner’s manual
for HDMI CEC compatibility)
If your TV does not support HDMI CEC volume and power control
another option is to program the soundbar to be controlled by
your TV remote control. For example, when you press POWER
ON, you will turn on your TV and soundbar at the same time. This
simplifies your system helps you keep your TV and speaker in
sync.
10
TV
Remote
3.
4.
5.
6.
Confirm that soundbar is ON
Press and hold the top-panel Harman Display Surround
Button for 5 seconds until the power LED flashes amber. If the
LED does not flash, release the button and try again.
Press the soundbar top-panel VOLUME UP button
Aim the TV remote at the front of the JBL Cinema SB450 and
slowly press the VOLUME UP button on the TV remote until
the Harman Display Surround button flashes white for one
second. This indicates that the programming operation has
been successful.
Repeat steps 3 and 4 for VOLUME DOWN, POWER, and
MUTE (to mute the JBL Cinema SB450, press VOLUME UP
and VOLUME DOWN buttons at the same time).
To exit the learning mode (at any time or when the learning
is complete), press and hold the Harman Display Surround
button until the amber LED stops flashing.
RESETING THE SOUNDBAR
The JBL Cinema SB450 can be reset to its default factory settings
and erasing all programming.
To reset the soundbar, press and hold Volume+ and Virtual
Surround buttons for 5s.
English
TROUBLESHOOTING
If your JBL Cinema SB450 does not perform the way you think it should, check whether the problem is covered in this section before
contacting you dealer or a JBL representative.
Problems
Solutions
If the speaker does not turn ON
•
Check if the speaker AC power cord is plugged into a working
AC outlet and that the cable is plugged into the speaker.
If there is no sound coming from the speaker
•
Check the power is set to ON, then check to see if the volume
is turned up.
Check if your TV has certain settings to enable the audio
connection, or try to connect another source.
•
If there is NO sound from the system, even when the speaker’s
volume is turned all the way up
•
If the TV or source component is connected via a variable
output, check its instructions if the output is not turned down
too low, or try to connect to another source.
If there is no picture on the TV Screen
•
Check that the soundbar power is ON, the intended source is
ON, and the input is set correctly on the soundbar.
The subwoofer is not playing
•
Check that the power is ON, and that the subwoofer is
correctly paired to the soundbar.
There is no sound using the optical input
•
Optical input does not support all surround sound formats.
JBL recommend to use HDMI connection if other sound
formats are used.
SPECIFICATIONS
Total Cinema SB450 Amplifier Power: 440W
Max SPL: 103dB
Frequency Response: 40Hz-20kHz
HDMI Video Inputs: 3
HDMI Video Output (with Audio Return Channel): 1
Bluetooth Version: 3.0
Max Bluetooth Range: 32 ft (10m)
Soundbar Amplifier Power: 240W
Soundbar Transducer Size: 2.25” (58mm)
Soundbar Dimensions (L x W x H): 44” x 3” x 4” (1100 x 76 x 97mm)
Soundbar Weight: 7.5lbs (3.4kg)
Soundbar Power Consumption (standby): <0.5W
Soundbar Power Consumption (max): 60W
Subwoofer Amplifier Power: 200W
Subwoofer Transducer Size: 8” (200mm)
Subwoofer Dimensions (L x W x H): 13” x 13” x 14” (320 x 320 x 355.5mm)
Subwoofer Weight: 21lbs (9.5kg)
Subwoofer Power Consumption (standby): <0.5W
Subwoofer Power Consumption (max): 100W
Packaging Dimensions (L x W x H): 46” x 16” x 19” (1210 x 395 x 520mm)
Packaging Weight (Gross): 35lbs (16kg)
www.jbl.com
11
ĶŒŔŇŒņńţŐńŔŎń
! 1)3
ıńŋőńśʼnőŌʼnŖŒņńŔń
! ĤŎŖŌņőńţńŎŗŕŖŌśʼnŕŎńţŕŌŕŖʼnŐń
ĬŋŇŒŖŒņŌŖʼnŏŠ
!ĹńŔŐńőĬőŖʼnŔőʼnŜőŏĬőňńŕŖŔŌŋĬőŎŒŔœŒŔʼnōŖʼnňĵļĤ ĮŒőőʼnŎŖŌŎŗŖŇĵŖšŐŘŒŔň
ĤŖŏńőŖŌŎĵŖŔŌŖŒŘŌŕ
ĵŖŔńőńœŔŒŌŕřŒŊňʼnőŌţ
!ĮŌŖńō
ĬŐœŒŔŖʼnŔņĴŒŕŕŌŢ
!666¸ĹĤĴİĤıĴķĵĵŌĤōŁŕ¸ĴŒŕŕŌţŇİŒŕŎņńŗŏĨņŌőŚʼnņňŎ
ħńŔńőŖŌōőşōœʼnŔŌŒň
!ŇŒň
ĬőŘŒŔŐńŚŌţŒŕʼnŔņŌŕőşřŚʼnőŖŔńř !^^^OHYTHUJVTY\Ŗʼnŏ
ĵŔŒŎŕŏŗŊŅş
!ŏʼnŖ
ĶŒņńŔŕʼnŔŖŌŘŌŚŌŔŒņńő
ĨńŖńœŔŒŌŋņŒňŕŖņń
!ĨńŖńŌŋŇŒŖŒņŏʼnőŌţŗŕŖŔŒōŕŖņńŒœŔʼnňʼnŏţʼnŖŕţœŒňņŗŐŅŗŎņʼnőőşŐŒŅŒŋőńśʼnőŌţŐŌŋņŖŒŔŒōŇŔŗœœş
ŕŌŐņŒŏŒņŕʼnŔŌōőŒŇŒőŒŐʼnŔńŌŋňʼnŏŌţŕŏʼnňŗŢŝŌřœŒŕŏʼnŔńŋňʼnŏŌŖʼnŏŠőŒŇŒŋőńŎń­®ĮŒňŌŔŒņŎń
ŕŒŒŖņʼnŖŕŖņŗʼnŖœŒŔţňŎŗŅŗŎņŏńŖŌőŕŎŒŇŒńŏŘńņŌŖńőńśŌőńţŕţőņńŔţŇŒňń!4@
Ňňʼn­4®ŐʼnŕţŚœŔŒŌŋņŒňŕŖņńĤţőņńŔŠ)ŘʼnņŔńŏŠ*ŐńŔŖŌŖňŌ­@®ŇŒňœŔŒŌŋņŒňŕŖņń(
)*ŌŖň
HARMAN International Industries,
Incorporated 8500 Balboa
Boulevard, Northridge, CA 91329
USA
www.jbl.com
© 2016 HARMAN International Industries, Incorporated. All rights reserved. JBL is a
trademark of HARMAN International Industries, Incorporated, registered in the United
States and/or other countries. Features, specifications and appearance are subject to
change without notice. The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International
Industries, Incorporated is under license. Other trademarks and trade names are
those of their respective owners. The terms HDMI, the HDMI logo, and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries. Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby
Laboratories.
TR03305_A
12
Cinema SB450
4K Ultra-HD soundbar with wireless subwoofer
Amplify the 4K Ultra-HD revolution with the sound only JBL can deliver.
Features
The JBL Cinema SB450 soundbar fills your home cinema with superb JBL sound and is
4K Ultra-HD Soundbar
fully compatible with 4K Ultra-HD televisions. The JBL Cinema SB450’s Remote Control
Learning feature allows you control the whole system with the TV remote you already have.
8-inch (200mm) 200W Wireless
Subwoofer
A 200W wireless subwoofer delivers room-shaking bass from a compact enclosure. Three
3 HDMI Inputs/1 HDMI Output (ARC)
HDCP 2.2 video inputs you use the soundbar as the hub for your 4K system. Included wall
Wireless Bluetooth Streaming
brackets allow seamless installation in your home. Exclusive JBL SoundShift™ technology
TV Remote Control Learning
lets you instantly switch between the sound from your TV and your phone or tablet. Stream
Bluetooth audio simultaneously to the JBL Cinema SB450 and any other JBL Connectenabled device for an amplified listening experience.
Clear Dialogue and Voice Enhancement
JBL SoundShift™
JBL Connect
Virtual Surround Sound
Cinema SB450
4K Ultra-HD soundbar with wireless subwoofer
Technical specifications:
Features and Benefits
4K Ultra-HD Soundbar
Works seamlessly with 4K Ultra-HD displays and devices. (Features High Dynamic Range (HDR)
and HDCP 2.2).
Total Cinema SB450 Amplifier Power: 440W
8-inch (200mm) 200W Wireless Subwoofer
Deep bass with adjustable subwoofer volume control.
HDMI Video Inputs: 3
3 HDMI Inputs/1 HDMI Output (ARC)
Connect up to 3 devices to the soundbar and one seamless connection to your TV.
Wireless Bluetooth Streaming
Wirelessly connect smartphones or tablets to the speaker. Play audio with vibrant,
room-filling sound.
TV Remote Control Learning
Keep life simple and control everything with the remote you already use for your TV.
(JBL remote control also included in the box).
Clear Dialogue and Voice Enhancement
Hear the dialogue in movies more clearly without changing the volume.
JBL SoundShift™
Allows you to instantly switch between sound from your TV and sound from your phone or tablet.
JBL Connect
Build your own ecosystem by connecting multiple JBL Connect enabled speakers together to
amplify the listening experience.
Virtual Surround Sound
Experience virtual surround sound without additional wires or speakers with
Harman Display Surround.
What’s in the box:
Soundbar
Wireless subwoofer
Optical cable (5 ft, 1500mm)
HDMI cable (3 ft, 1000mm)
2 power cables
Remote control
Wall-mount brackets
Quick-start guide
Printed mounting template
Warranty card
HARMAN International Industries, Incorporated
8500 Balboa Boulevard, Northridge, CA 91329 USA
www.jbl.com
Max SPL: 103dB
Frequency Response: 40Hz-20kHz
HDMI Video Output
(with Audio Return Channel): 1
HDCP Version: 2.2
Bluetooth Version: 3.0
Max Bluetooth Range: 32ft (10m)
Soundbar Amplifier Power: 240W
Soundbar Transducer Size: 2.25" (58mm)
Soundbar Dimensions (L x W x H):
44" x 3" x 4" (1100 x 76 x 97mm)
Soundbar Weight: 7.5lbs (3.4kg)
Soundbar Power Consumption (standby):
<0.5W
Soundbar Power Consumption (max): 60W
Subwoofer Amplifier Power: 200W
Subwoofer Transducer Size: 8" (200mm)
Subwoofer Dimensions (L x W x H):
13" x 13" x 14" (320 x 320 x 355.5mm)
Subwoofer Weight: 21lbs (9.5kg)
Subwoofer Power Consumption (standby):
<0.5W
Subwoofer Power Consumption (max): 100W
Packaging Dimensions (L x W x H):
46" x 16" x 19" (1210 x 395 x 520mm)
Packaging Weight (Gross): 35lbs (16kg)
© 2016 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark of HARMAN International
Industries, Incorporated, registered in the United States and/or other countries. The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries,
Incorporated is under license. Other trademarks and trade names are those of their respective owners. HDMI is a
registered trademark of HDMI Licensing, LLC in the United States and/or other countries. Manufactured under license from
Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Features, specifications and
appearance are subject to change without notice.
">