ASUS Terminator 2 T2-AE1 Barebone System Používateľská príručka

Terminator 2
Barebone System
Model T2-AE1
E1920
First Edition V1
February 2005
Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the
serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
ii
Table of contents
Notices ................................................................................................ vi
Safety information ............................................................................. vii
About this guide ............................................................................... viii
System package contents ................................................................... x
Chapter 1: System Introduction
1.1
Welcome! .............................................................................. 1-2
1.2
Front panel (external) .......................................................... 1-2
1.3
Front panel (internal) ........................................................... 1-4
1.4
Rear panel ............................................................................. 1-5
1.5
Internal components ............................................................ 1-7
Chapter 2:
Basic Installation
2.1
Preparation ........................................................................... 2-2
2.2
Before you proceed .............................................................. 2-2
2.3
Removing the cover ............................................................. 2-3
2.4
Removing the power supply ................................................. 2-4
2.5
Installing a CPU ..................................................................... 2-5
2.6
Installing the CPU fan and heatsink assembly ...................... 2-7
2.7
Installing a DIMM ................................................................... 2-8
2.8
2.7.1
Memory configurations ........................................... 2-8
2.7.2
DIMM installation ................................................... 2-10
Installing an expansion card ............................................... 2-11
2.8.1
Expansion slots ..................................................... 2-11
2.8.2
AGP 8X slot .......................................................... 2-11
2.8.3
Expansion card installation ................................... 2-12
2.8.4
Configuring an expansion card .............................. 2-13
2.9
Installing an optical drive .................................................... 2-14
2.10
Installing a floppy disk drive ............................................... 2-17
2.11
Installing a hard disk drive (HDD) ....................................... 2-18
2.12
Reinstalling the power supply unit ...................................... 2-20
2.13
Replacing the cover ............................................................ 2-22
2.14
Connecting external devices .............................................. 2-23
iii
Table of contents
Chapter 3:
3.1
Installing an operating system ............................................. 3-2
3.2
Powering up .......................................................................... 3-2
3.3
Support CD information ........................................................ 3-2
3.4
3.3.1
Running the support CD ......................................... 3-3
3.3.2
Drivers menu .......................................................... 3-3
3.3.3
Utilities menu .......................................................... 3-4
3.3.4
ASUS contact information ...................................... 3-6
3.3.5
Other information ................................................... 3-6
Software information ........................................................... 3-7
3.4.1
ASUS Instant Music ................................................. 3-7
3.4.2
ASUS Radio Player .................................................. 3-9
Chapter 4:
Motherboard Info
4.1
Introduction .......................................................................... 4-2
4.2
Motherboard layout .............................................................. 4-2
4.3
Jumpers ................................................................................ 4-3
4.4
Connectors ........................................................................... 4-5
Chapter 5:
5.1
5.2
iv
Starting up
BIOS Information
Managing and updating your BIOS ........................................ 5-2
5.1.1
Creating a bootable floppy disk .............................. 5-2
5.1.2
ASUS EZ Flash utility .............................................. 5-3
5.1.3
AFUDOS utility ........................................................ 5-4
5.1.4
ASUS CrashFree BIOS 2 utility ................................ 5-6
5.1.5
ASUS Update utility ................................................ 5-8
BIOS setup program ........................................................... 5-11
5.2.1
BIOS menu screen ................................................. 5-12
5.2.2
Menu bar ............................................................... 5-12
5.2.3
Navigation keys .................................................... 5-12
5.2.4
Menu items ........................................................... 5-13
5.2.5
Sub-menu items ................................................... 5-13
5.2.6
Configuration fields .............................................. 5-13
5.2.7
Pop-up window ..................................................... 5-13
5.2.8
Scroll bar .............................................................. 5-13
5.2.9
General help .......................................................... 5-13
Table of contents
5.3
5.4
5.5
5.6
5.7
Main menu .......................................................................... 5-14
5.3.1
System Time ......................................................... 5-14
5.3.2
System Date ......................................................... 5-14
5.3.3
Legacy Diskette A ................................................ 5-14
5.3.4
Primary IDE Master/Slave ..................................... 5-15
5.3.5
Onboard PCI S-ATA Controller .............................. 5-16
5.3.6
System Information .............................................. 5-17
Advanced menu .................................................................. 5-18
5.4.1
CPU Configuration ................................................. 5-18
5.4.2
Chipset ................................................................. 5-20
5.4.3
Onboard Devices Configuration ............................ 5-22
5.4.4
PCI PnP ................................................................. 5-25
5.4.5
Instant Music Configuration .................................. 5-27
Power menu ........................................................................ 5-28
5.5.1
Suspend Mode ...................................................... 5-28
5.5.2
Repost Video on S3 Resume ................................ 5-28
5.5.3
ACPI 2.0 Support .................................................. 5-28
5.5.4
ACPI APIC Support ................................................ 5-28
5.5.5
APM Configuration ................................................ 5-29
5.5.6
Hardware Monitor ................................................. 5-30
Boot menu .......................................................................... 5-32
5.6.1
Boot Device Priority .............................................. 5-32
5.6.2
Boot Settings Configuration ................................. 5-33
5.6.3
Security ................................................................ 5-34
Exit menu ........................................................................... 5-36
Appendix
Power supply specifications ............................................................. A-2
v
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
W A R N I N G ! The use of shielded cables for connection of the monitor to
the graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing devices into the system, carefully read all the
documentation that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet. Place the product on a
stable surface.
• If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
Lithium-Ion Battery Warning
CAUTION
N: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturerís instructions.
VORSICHT
T: Explosionsgetahr bei unsachgemäßen Austausch der
Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
LASER PRODUCT WARNING
CLASS 1 LASER PRODUCT
vii
About this guide
Audience
This guide provides general information and installation instructions about
the ASUS Terminator 2 barebone system. This guide is intended for
experienced users and integrators with hardware knowledge of personal
computers.
How this guide is organized
This guide contains the following parts:
1.
Chapter 1: System introduction
This chapter gives a general description of the ASUS Terminator 2.
The chapter lists the system features, including introduction on the
front and rear panel, and internal components.
2.
Chapter 2: Basic installation
This chapter provides step-by-step instructions on how to install
components in the system.
3.
Chapter 3: Starting up
This chapter helps you power up the system and install drivers and
utilities from the support CD.
4.
Chapter 4: Motherboard information
This chapter gives information about the motherboard that comes
with the system. This chapter includes the motherboard layout,
jumper settings, and connector locations.
5.
Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS
Setup menus and describes the BIOS parameters.
6.
viii
Appendix
The Appendix includes the power supply unit specification for this
system.
Conventions used in this guide
W A R N I N G : Information to prevent injury to yourself when
trying to complete a task.
C A U T I O N : Information to prevent damage to the components
when trying to complete a task.
I M P O R T A N T : Instructions that you MUST follow to complete a
task.
N O T E : Tips and additional information to aid in completing a
task.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1.
ASUS Websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to the ASUS contact
information.
2.
Optional Documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
ix
System package contents
Check your Terminator 2 system package for the following items.
If any of the items is damaged or missing, contact your retailer
immediately.
Item description
1 . A S U S T e r m i n a t o r 2 b a r e b o n e s y s t e m with
• ASUS motherboard
• 200 W Passive PFC power supply unit
• 10/100 Mbps Ethernet LAN port
• CPU fan and heatsink assembly
• 2 x 5.25” drive bays
• 1 x 3.5” floppy disk drive bay
• 1 x 3.5” hard disk drive bay
• 6 x USB 2.0 ports
• 2 x IEEE 1394a ports
• S/PDIF out port
2 . Cables
• AC power cable
• Serial ATA cable
• Serial ATA power cable
• 2-in-1 disk drive cable
• Floppy disk drive cable
3 . Support CD
4 . User guide
5 . Optional items
• Optical drive (CD-ROM/CD-RW/DVD-ROM/DVD-RW)
• Floppy disk drive
x
This chapter gives a general
description of the ASUS
Terminator 2. The chapter lists the
system features including
introduction on the front and rear
panel, and internal components.
ASUS T2-AE1
System introduction
Chapter 1
1.1
Welcome!
Thank you for choosing the ASUS Terminator 2!
The ASUS Terminator 2 is an all-in-one barebone system with a versatile
home entertainment feature.
The system comes in a stylish mini-tower casing, and powered by the ASUS
motherboard that supports the AMD Athlon™ 64/Athlon™ XP processor
with 800 MHz FSB and up to 2 GB system memory.
Supporting up to six USB 2.0 ports and Ethernet LAN, Terminator 2 offers
extensive connectivity, digital entertainment, and efficient networking
capabilities to meet your personal as well as business requirements.
With these and many more, the Terminator 2 definitely delivers the cutting
edge technology for your computing and multimedia needs!
1.2
Front panel (external)
The front panel includes the system and audio control buttons, system
LEDs, and LED panel.
1
2
3
4
5
6
7
8
1-2
Chapter 1: System introduction
1.
2.
F l o p p y d r i v e d o o r . Open this door to access the floppy disk drive.
O p t i c a l d r i v e d o o r . This door opens when you eject the loading
tray.
3.
E j e c t b u t t o n . Press this button to eject the optical drive loading
tray.
S e c o n d o p t i c a l d r i v e d o o r . This door covers a second optical
drive bay.
4.
. Press this button to turn the system on.
5.
Power button
6.
Power LED
7.
HDD LED
. This LED lights up when data is being read from or
written to the hard disk drive
F r o n t p a n e l I / O d o o r . Open this door to show the front panel
input/output ports.
8.
ASUS T2-AE1
. This LED lights up to indicate that the system is ON.
1-3
1.3
Front panel (internal)
The optical drive(s), storage card reader slots, and several I/O ports are
located inside the front panel doors.
Open the front panel doors by pressing the
9
mark.
10
5
1 1 1 2 1 3 1284 130
9 . F l o p p y d i s k d r i v e . This drive is for a 1.44 MB, 3.5-inch floppy disk.
0.. O p t i c a l d r i v e (optional). This is an IDE optical drive.
10
1 1 . Headphone port
mini-plug.
. This port connects a headphone with a stereo
1 2 . Microphone port
. This Mic (pink) port connects a microphone.
1 3 . USB 2.0 ports
2.0 . These Universal Serial Bus 2.0 (USB 2.0)
ports are available for connecting USB 2.0 devices such as a mouse,
printer, scanner, camera, PDA, and others.
1 4 . 4-pin IEEE 1394a port
. This port provides high-speed
connectivity for IEEE 1394a-compliant audio/video devices, storage
peripherals, and other PC devices.
1 5 . 6-pin IEEE 1394a port
. This port provides high-speed
connectivity for IEEE 1394a-compliant audio/video devices, storage
peripherals, and other PC devices.
1-4
Chapter 1: System introduction
1.4
Rear panel
The system rear panel includes the power connector and several I/O ports
that allow convenient connection of devices.
Deluxe model
1
14
2
3
4
5
6
7
15
8
9
16
10
17
11
12
18
13
1.
G A M E / M I D I p o r t . This port connects a joystick or game pad for
playing games, and MIDI devices for audio editing.
2.
O p t i c a l S / P D I F p o r t . This port connects your audio system for
5.1-channel surround sound and enhanced 3D audio.
3.
Serial port
. This port connects a mouse, modem, or other
devices that conforms with serial specification.
4.
PS/2 mouse port
mouse.
5.
PS/2 keyboard port
PS/2 keyboard.
6.
VGA port
7.
Parallel port
other devices.
8.
Line Out port
. This Line Out (lime) port connects a headphone
or a speaker. In 4/6-channel mode, the function of this port becomes
Front Speaker Out.
ASUS T2-AE1
. This green 6-pin connector is for a PS/2
. This purple 6-pin connector is for a
. This port connects a VGA monitor.
. This 25-pin port connects a printer, scanner, or
1-5
9.
Line In port
. This Line In (light blue) port connects a tape
player or other audio sources. In 6-channel mode, the function of this
port becomes Low Frequency Enhanced Output/Center.
1 0 . Microphone port
. This Microphone (pink) port connects a
microphone. In 4/6-channel mode, the function of this port becomes
Surround Speaker.
The functions of the Line Out, Line In, and Microphone ports change
when you select the 6-channel configuration. Refer to the table below
for audio ports function variation.
Audio ports function variation
Port
Headphone/2-Channel
4-Channel
6-Channel
Light Blue
Line In
No function
LFE Output*/Center
Lime
Line Out
Front Speaker Out
Front Speaker Out
Pink
Mic In
Surround
Surround
* Low Frequency Enhanced Output
1 1 . USB 2.0 ports
2.0 . These Universal Serial Bus 2.0 (USB 2.0)
ports are available for connecting USB 2.0 devices such as a mouse,
printer, scanner, camera, PDA, and others.
1 2 . LAN (RJ-45) port
. This port allows Gigabit connection to a
Local Area Network (LAN) through a network hub.
1 3 . E x p a n s i o n s l o t c o v e r ss. Remove these cover when installing
expansion cards.
1 4 . C h a s s i s f a n v e n t . This vent is for the fan that provides ventilation
inside the system chassis.
1 5 . P o w e r s u p p l y u n i t f a n v e n t . This vent is for the PSU fan that
provides ventilation inside the power supply unit.
1 6 . P o w e r c o n n e c t o r . This connector is for the power cable and plug.
1 7 . V o l t a g e s e l e c t o r . This switch allows you to adjust the system
input voltage according to the voltage supply in your area. See the
“Voltage selector” section on page 2-21 before adjusting this switch.
1 8 . E x p a n s i o n c a r d l o c k . This lock secures installed expansion cards.
See page 2-12 for details.
1-6
Chapter 1: System introduction
1.5
Internal components
The illustration below is the internal view of the system when you remove
the top cover and the power supply unit. The installed components are
labeled for your reference. Proceed to Chapter 2 for instructions on
installing additional system components.
1
6
3
2
4
9
7
11
8
10
13
5
12
1.
Optical drive (optional)
2.
5.25-inch empty optical drive bay
3.
Floppy disk drive (optional)
4.
Front panel cover
5.
Hard disk drive metal tray
6.
Chassis fan
7.
ASUS motherboard
8.
DIMM sockets
9.
CPU heatsink and fan
10. AGP slot
11. PCI slot
12. Serial ATA connectors
13. Expansion card slots
ASUS T2-AE1
1-7
1-8
Chapter 1: System introduction
Chapter 2
Basic installation
This chapter provides step-by-step
instructions on how to install
components in the system.
ASUS T2-AE1
2.1
Preparation
Before you proceed, make sure that you have all the components you plan
to install in the system.
Basic components to install
1. Central processing unit (CPU)
2. DDR Dual Inline Memory Module (DIMM)
3. Expansion card(s)
4. Hard disk drive
5. Optical drive
6. Floppy disk drive
Tool
Phillips (cross) screw driver
2.2
Before you proceed
Take note of the following precautions before you install components into
the system.
•
Use a grounded wrist strap or touch a safely grounded object or a
metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
The motherboard comes with an onboard standby power LED. This LED
lights up to indicate that the system is ON, in sleep mode or in soft-off
mode, and not powered OFF. Unplug the power cable from the power outlet
and make sure that the standby power LED is OFF before installing any
system component.
SB_PWR
®
Onboard LED
2-2
ON
Standby
Power
OFF
Powered
Off
Chapter 2: Basic installation
2.3
Removing the cover
To remove the cover:
1.
On the rear panel, locate the
three screws that secure the
cover to the chassis.
1
1
2.
Use a Phillips screw driver to
remove the cover screws. Keep
the screws for later use.
1
2
2
2
3.
4.
Slightly pull the cover toward
the rear panel until the side tabs
are disengaged from the
chassis.
4
Lift the cover, then set aside.
3
ASUS T2-AE1
3
2-3
2.4
Removing the power supply
You must remove the power supply unit (PSU) before you can install a
central processing unit( CPU) and other system components.
To remove the PSU:
1.
Lay the system on its side on a
flat, stable surface.
2.
Disconnect the optical drive and
floppy disk drive power plugs.
3.
Remove the screw that secures
the PSU to the chassis.
4.
Slide the PSU as the zoomed
image shows, until the side hook
is disengaged from the chassis.
5.
Push the PSU towards the front
panel for about half an inch.
6.
Slightly lift the PSU.
3
6
4
5
7.
Disconnect the power plugs on
the motherboard, then set the
PSU aside.
When removing the PSU,
make sure to hold or support
it firmly. The unit may
accidentally drop and damage
other system components.
2-4
7
7
Chapter 2: Basic installation
2.5
Installing a CPU
The motherboard comes with a surface mount 754-pin Zero Insertion Force
(ZIF) socket designed for the AMD Athlon™ 64 processor in the 754-pin
lidded ceramic micro PGA package.
Take note of the marked corner (with
gold triangle) on the CPU. This mark
should match a specific corner on the
socket to ensure correct installation.
Gold triangle
Incorrect installation of the CPU into the socket may bend the pins and
severely damage the CPU!
Installing the CPU
To install a CPU:
1.
Locate the 754-pin ZIF socket on the motherboard.
®
CPU Socket 775
ASUS T2-AE1
2-5
2.
Unlock the socket by pressing
the lever sideways, then lift it up
to a 90°-100° angle.
Socket lever
Make sure that the socket
lever is lifted up to 90°-100°
angle, otherwise the CPU does
not fit in completely.
3.
Position the CPU above the
socket such that the CPU corner
with the gold triangle matches
the socket corner with a small
triangle.
4.
Carefully insert the CPU into the
socket until it fits in place.
Gold triangle
The CPU fits only in one correct orientation. DO NOT force the CPU into
the socket to prevent bending the pins and damaging the CPU!
2-6
5.
When the CPU is in place, push
down the socket lever to secure
the CPU. The lever clicks on the
side tab to indicate that it is
locked.
6.
Install a CPU heatsink and fan
following the instructions that
came with the heatsink package.
7.
Connect the CPU fan cable to the
CPU_FAN connector on the
motherboard.
Chapter 2: Basic installation
2.6
Installing the CPU fan and heatsink
assembly
Make sure to turn off your computer and unplug the cable from the
power source before installing the CPU fan and heatsink assembly.
To install the CPU fan and heatsink assembly:
1.
Remove the CPU fan and
heatsink assembly from its
packaging and vacuum cover.
2.
Place the CPU fan and heatsink
assembly on top of the
installed CPU, making sure it
fits the retention module.
3.
Connect the CPU fan cable to
the CPU fan connector on the
motherboard.
4.
Align the metal clips to the side
rail of the CPU fan and heatsink
assembly, with the locking
levers in the reverse orientation.
4.
Snap the hook of each metal clip
into the hole of the retention
module.
2
3
Locking levers
4
5
5
Hook
Metal clip
5.
Carefully press down each
locking lever and hook its end
into the hole of the retention
module.
6
6
ASUS T2-AE1
2-7
2.7
Installing a DIMM
The system motherboard comes with two Double Data Rate (DDR) Dual
Inline Memory Module (DIMM) sockets.
®
DIMM2
80 Pins
104 Pins
DIMM1
The following figure illustrates the location of the sockets:
184-pin DDR DIMM sockets
2.7.1
Memory configurations
You may install up to 2 GB system memory using 256 MB, 512 MB, and
1 GB DDR DIMMs.
2-8
•
Installing DDR DIMMS other than the recommended configurations
may cause memory sizing error or system boot failure. Use any of
the recommended configurations in the table on the next page.
•
Install only i d e n t i c a l (the same type and size) DDR DIMM in
DIMM_A and DIMM_B.
•
Always install DIMMs with the same CAS latency. For optimum
compatibility, we recommend that you obtain memory modules from
the same vendor.
•
Due to chipset resource allocation, the system may detect less than
2 GB system memory when you installed two 1 GB DDR memory.
•
If you installed two 400 MHz DDR memory modules, the memory
frequency downgrades to 333 MHz.
Chapter 2: Basic installation
Recommended memory configurations
Sockets
Mode
Single-channel
DIMM1
DIMM2
(1)
Installed
—
(2)
—
Installed
(3)* Installed
Installed
* Use only identical DDR DIMM pairs.
DDR (400 MHz) Qualified Vendors List
Size
Vendor
Model
Side/s*
Component
256MB
KINGSTON
HY5DU56822BT-D43
SS
KVR400X64C3A/256
512MB
KINGSTON
HY5DU56822BT-D43
DS
KVR400X64C3A/512
512MB
KINGSTON
HYB25D256809BT-5B
DS
KVR400X64C3A/512
512MB
KINGSTON
D328DIB-50
DS
KVR400X64C3A/512
256MB
SAMSUNG
K4H560838F-TCCC
SS
M368L3223FTN-CCC
512MB
SAMSUNG
K4H560838F-TCCC
DS
M368L6423FTN-CCC
256MB
MICRON
MT46V32M8TG-5BC
SS
MT8VDDT3264AG-40BCB
512MB
MICRON
MT46V32M8TG-5BC
DS
MT16VDDT6464AG-40BCB
256MB
Infineon
HYB25D256800CE-5C
SS
HYS64D32300HU-5-C
512MB
Infineon
HYB25D256800CE-5C
DS
HYS64D64320HU-5-C
256MB
CORSAIR
W942508BH-5
SS
CMX256A-3200C2PT
512MB
CORSAIR
VS32M8-5
DS
VS512MB400
256MB
Hynix
HY5DU56822DT-D43
SS
HYMD232645D8J-D43
512MB
Hynix
HY5DU56822DT-D43
DS
HYMD264646D8J-D43
Obtain DDR DIMMs only from ASUS qualified vendors. Refer to the
Qualified DDR400 vendors list on this page. Visit the ASUS website
(www.asus.com) for the latest DDR Qualified Vendors List.
ASUS T2-AE1
2-9
2.7.2
DIMM installation
To install a DDR DIMM.
1.
Locate the two DIMM sockets
on the motherboard.
2.
Unlock a socket by pressing
the retaining clips outward.
3.
Align a DIMM on the socket
such that the notch on the
DIMM matches the break on
the socket.
4.
Firmly insert the DIMM into
the socket until the retaining
clips snap back in place and
the DIMM is properly seated.
Retaining clips
3
2
4
2
4
1
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM!
2-10
Chapter 2: Basic installation
2.8
Installing an expansion card
In the future, you may need to install expansion cards. The motherboard
has one PCI and one AGP 8X slot. The following sub-sections describe the
slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage the motherboard.
2.8.1
Expansion slots
PCI slot
The PCI slot supports PCI cards such
as a LAN card, SCSI card, USB card,
and other cards that comply with PCI
specifications. The following figure
shows a LAN card installed on a PCI
slot.
2.8.2
AGP 8X slot
This motherboard has an Accelerated Graphics Port (AGP) slot that
supports +1.5V AGP cards. When you buy an AGP card, make sure that you
ask for one with +1.5V specification. Note the notches on the card golden
fingers to ensure that they fit the AGP slot on your motherboard.
Keyed for 1.5v
®
Floppy Accelerated Graphics Port (AGP)
Install only 1.5V AGP cards on this motherboard!
ASUS T2-AE1
2-11
2.8.3
Expansion card installation
To install an expansion card.
1.
Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2.
Pull the expansion card lock to
the direction of the arrow.
2
Expansion
card lock
3.
Remove the metal cover
opposite the slot that you
intend to use.
PCI
slot
AGP 8x slot
3
Metal covers
4.
Align the card connector with
the slot and press firmly until
the card is completely seated on
the slot.
4
PCI card
5.
Replace the expansion card lock
to secure the card to the
chassis.
5
2-12
Chapter 2: Basic installation
2.8.4
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software
settings.
1.
Turn on the system and change the necessary BIOS settings, if any.
See Chapter 5 for information on BIOS setup.
2.
Assign an IRQ to the card. Refer to the tables on the next page.
3.
Install the software drivers for the expansion card.
Standard interrupt assignments
IRQ
Standard Function
0
1
2
4
6
7*
8
9*
10*
11*
12*
13
System Timer
Keyboard Controller
Programmable Interrupt
Communications Port (COM1)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
14*
Primary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
A
PCI slot 1
AGP 8x slot
Onboard USB controller 1
Onboard USB controller 2
Onboard USB controller 3
Onboard USB controller 4
Onboard LAN
Onboard Audio
Onboard 1394
––
shared
––
––
––
shared
––
––
––
B
C
D
shared ––
––
––
––
––
––
––
––
––
–– shared
–– shared ––
––
––
––
shared ––
––
shared ––
––
––
––
––
E
F
G
H
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
shared
––
––
––
––
––
––
––
––
––
––
––
shared
––
––
––
––
––
––
When using a PCI card on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments; otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable.
ASUS T2-AE1
2-13
2.9
Installing an optical drive
The Terminator 2 system comes with two 5.25-inch drive bays for two
optical drives.
•
You may install a second optical drive only if you installed a Serial
ATA hard disk drive.
•
Set your second optical drive as Slave device before connecting the
IDE cable and power plug. Refer to the optical drive documentation
on how to set the drive as a Slave device.
To install an optical drive:
1.
Place the chassis upright.
2.
Locate the front panel cover
hooks.
3.
To remove the front panel cover
from the chassis, press the top
hooks downward and the
bottom hooks upward to release
them from the metal tabs that
secure them in place.
4.
Detach the front panel cover
top hooks.
3
3
1
2
3
3
4
4
5.
Slightly push the front panel
cover outward until it detaches
from the chassis, then set it
aside.
On Deluxe models, disconnect
the LED panel and the front
audio button panel cables
from their respective
connectors before removing
the front panel cover.
5
To reconnect the cables, see
pages 4-7 and 4-8 for the
location of the connectors.
2-14
Chapter 2: Basic installation
6.
Carefully push the optical drive
into the bay until its screw holes
align with the holes on the bay
as shown.
7.
Secure the optical drive with
two screws on one side of the
bay.
8.
9.
7
6
Connect a power cable from the
power supply unit to the power
connector at the back of the
optical drive. See page 2-21 for
details.
Connect the IDE ribbon cable to
the IDE interface at the back of
the optical drive, matching the
red stripe on the cable with Pin
1 on the IDE interface.
8
10
9
10. Connect one end of the optical
drive audio cable to the 4-pin
connector at the back of the
optical drive.
11. Make sure that the other end of
the IDE ribbon cable is connected
to the primary IDE connector (blue
connector labeled PRI_IDE) on the
motherboard. See page 4-8 for
the location of the primary IDE
connector.
12. Connect the other end of the
audio cable to the 4-pin CD1
connector on the motherboard.
See page 4-10 for the location of
the CD audio connector.
ASUS T2-AE1
2-15
13. Reinstall the front panel cover
by aligning its hooks with the
chassis holes.
13
14. Lock the front panel cover
hooks to the chassis holes as
indicated.
14
2-16
Chapter 2: Basic installation
2.10
Installing a floppy disk drive
The Terminator 2 system comes with one 3.25-inch drive bay for a floppy
disk drive.
To install a floppy disk drive:
1.
Remove the front panel cover.
For instructions on how to
remove the front panel cover,
refer to steps 1-5 of section
“2.8 Installing an optical
drive.”
2.
Carefully insert the floppy disk
drive into the floppy drive bay
until the screw holes align with
the holes on the bay.
3.
Secure the floppy disk drive with
two screws.
2
3
4.
Connect the floppy disk drive
signal cable to the signal
connector at the back of the
drive.
5.
Connect the other end of the
signal cable to the floppy disk
drive connector (labeled
FLOPPY) on the motherboard.
See page 4-10 for the
connector location.
6.
3
6
4
Connect a power cable from the
power supply unit to the power
connector at the back of the
floppy disk drive. See page 2-21 for
details on the power supply unit plugs.
ASUS T2-AE1
2-17
2.11
Installing a hard disk drive (HDD)
The system supports one Ultra ATA/133 IDE or one Serial ATA hard disk
drive.
To install an IDE hard disk drive:
1.
Locate the HDD tray lock screw
on the other side of the chassis.
2.
Remove the lock screw with a
Philips screw driver. Keep the
screw for later use.
1
2
3.
Slide the HDD tray outward until
the tray slots are released from
the chassis hooks.
Tray locks
3
Lock slots
Tray locks
4.
5.
Place a hard disk drive on the
tray with its bottom on the
open side. Align the HDD and
HDD tray screw holes.
5
4
Secure the HDD with four
screws.
5
Configure your hard disk drive as Master device before connecting the
IDE cable and power plug. Refer to the HDD documentation on how to
set the drive as a Master device.
2-18
Chapter 2: Basic installation
6.
Reinstall the tray and the HDD
to the chassis by locking the
tray slots to the chassis hooks.
7.
Secure the tray with the screw
you removed earlier.
6
7
8.
Connect one end of the 40-pin
IDE cable to the IDE connector
on the drive.
9.
Connect a 4-pin power plug
from the power supply unit to
the HDD power connector.
10. Connect the other end of the
IDE ribbon cable to the primary
IDE connector (blue connector
labeled PRI_IDE) on the
motherboard. See page 4-8 for
the location of the primary IDE
connector.
8
9
To install a Serial ATA hard disk drive:
1.
Follow steps 1-7 of the previous section.
2.
Connect one end of the supplied 7-pin SATA cable to the SATA
connector at the back of the drive, then connect the other end to a
SATA connector on the motherboard. See page 4-9 for the location of
the Serial ATA connectors.
3.
Connect the 15-pin SATA power adapter plug to the power connector
at the back of the drive, then connect the other end (4-pin male) to a
4-pin (female) power plug from the power supply unit.
ASUS T2-AE1
2-19
2.12
Reinstalling the power supply unit
Reinstall the power supply unit (PSU) after installing the system
components and reconnecting the cables, .
To reinstall the PSU:
1.
Connect the 4-pin 12 V power
plug to the ATX12V connector
on the motherboard. See page
4-10 for the location of this
connectors.
1
2.
Position the PSU over the
chassis.
3.
Align the PSU side hook with the
metal slot located on the side of
the optical drive bay.
4.
Slide the PSU toward the
direction of the rear panel until it
fits in place.
3
1
2
4
5.
Secure the PSU with the screw
you removed earlier.
Make sure the PSU cables do
not interfere with the CPU
and/or chassis fans.
6.
2-20
6
5
Connect the 20-pin ATX power
plug to the ATXPWR connector
on the motherboard. See page
4-8 for the location of this
connector.
Chapter 2: Basic installation
7
8
Power supply unit plugs
1
1
6
7.
Connect the 4-pin power plug to the power connector of the floppy
disk drive.
8.
Connect the 4-pin power plug(s) to the power connector of the
optical drive(s) or hard disk drive.
9.
Connect the 4-pin power plug to the power connector of the Serial
ATA (SATA) drive.
See the Appendix for the power supply specifications.
Voltage selector
The PSU has a 115 V/230 V voltage selector
switch located beside the power connector. Use
this switch to select the appropriate system
input voltage according to the voltage supply in
your area.
If the voltage supply in your area is 100-127 V,
set the switch to 115 V.
115
If the voltage supply in your area is 200-240 V,
set the switch to 230 V.
Setting the switch to 115 V in a 230 V environment will seriously
damage the system!
ASUS T2-AE1
2-21
2.13
Replacing the cover
To replace the cover:
1.
Turn the chassis upright.
2.
Position the front edge of the
cover at least two inches from
the front panel cover. Fit the
cover tabs with the chassis rail
and the front panel tabs.
3.
Lower the rear edge of the
cover as shown.
4.
Push the cover slightly toward
the front panel until it fits in
place.
5.
Secure the cover with the three
screws you removed earlier.
3
4
2
5
2-22
Chapter 2: Basic installation
2.14
Connecting external devices
To the front panel
Headphone
ASUS T2-AE1
Mic
Scanner
Camera
HDD
2-23
To the rear panel
Joystick
Serial mouse
PS
/2 Mouse
S/2
PS/2 KB
Printer
VGA monitor
Line Out
Recorder
Card reader
Po w e r
outlet
RJ-45
2-24
Mic
Chapter 2: Basic installation
Chapter 3
Starting up
This chapter helps you power up
the system and install drivers and
utilities from the support CD.
ASUS T2-AE1
3.1
Installing an operating system
Terminator 2 supports Windows® 2000/XP/2003 (32-bit) operating
systems (OS). Always install the latest OS version and corresponding
updates so you can maximize the features of your hardware.
Because motherboard settings and hardware options vary, use the setup
procedures presented in this chapter for general reference only. Refer to
your OS documentation for more information.
3.2
Powering up
The system has two power buttons located in the front panel. Press the
system power button ( ) to enter the OS.
Press to enter the
system OS
3.3
Support CD information
The support CD that came with the system contains useful software and
several utility drivers that enhance the system features.
3-2
•
Screen display and driver options may not be the same for other
operating system versions.
•
The contents of the support CD are subject to change at any time
without notice. Visit the ASUS website for updates.
Chapter 3: Starting up
3.3.1
Running the support CD
To begin using the support CD, place the CD in your optical drive. The CD
automatically displays the D r i v e r s menu if Autorun is enabled in your
computer.
Click an item to install
Click an icon to display
other information
If A u t o r u n is NOT enabled in your computer, browse the contents of
the support CD to locate the file ASSETUP.EXE from the BIN folder.
Double-click the A S S E T U P . E X E to run the CD.
3.3.2
Drivers menu
The drivers menu shows the available device drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.
SiS AGP Driver
Installs the SiS AGP driver.
SiS Graphics Adapter Drivers
Installs the SiS graphics adapter drivers.
Realtek AC`97 Drivers Applications
Installs the Realtek® AC`97 drivers and applications.
ASUS T2-AE1
3-3
SiS191/SiS190 Ethernet Device Driver
Installs the SiS191/SiS190 ethernet device driver.
SiS180/182 RAID Controller Drivers
Installs the SiS180/182 RAID controller drivers.
Make SiS180/182 SATA Driver Disk
Allows you to make a SiS180/182 Serial ATA driver disk.
USB 2.0 Card Reader Software
Installs the driver for the storage card reader. This item appears only on
Deluxe models.
AMD Cool ‘n’ Quiet Drivers
Installs the AMD Cool ‘n’ Quiet!™ Technology driver. Cool ‘n’ Quiet!™
Technology allows the system to dynamically and automatically select the
CPU speed, voltage, and power combination that matches the user’s
performance requirements.
USB 2.0 Driver
Click this item to install the USB 2.0 driver.
3.3.3
Utilities menu
The Utilities menu shows the applications and other software that the
motherboard supports.
3-4
Chapter 3: Starting up
ASUS PC Probe
This smart utility continuously monitors vital system information such as
fan rotations, CPU temperature, and system voltages, and alerts you on
any detected problems. This utility helps you keep your computer in a
healthy operating condition.
ASUS Update
Installs the ASUS Update that allows you to update the motherboard BIOS
and drivers. This utility requires an Internet connection either through a
network or an Internet Service Provider (ISP). See page 5-8 for details.
ASUS Radio Application
Installs the ASUS radio application that allows you to tune in to an FM radio
station. See page 3-9 for details.
ASUS Screensaver
Bring life to your idle screen by installing the ASUS Screensaver.
AMD Cool ‘n’ Quiet Utility
Installs the AMD Cool ‘n’ Quiet!™ software.
Adobe Acrobat Reader V5.0
The Acrobat® Acrobat Reader® software is for viewing files saved in
Portable Document Format (PDF).
Microsoft DirectX 9.0c Driver
Installs the Microsoft® DirectX 9.0c driver. The Microsoft® DirectX 9.0c is a
multimedia techology that enhances computer graphics and sounds.
DirectX® improves the multimedia featuers of your computer so you can
enjoy watching TV and movies, capturing videos, or playing games on your
computer.
Anti-virus Utility
The anti-virus application scans, identifies, and removes computer viruses.
View the online help for detailed information.
ASUS T2-AE1
3-5
3.3.4
ASUS contact information
The Contact tab displays the ASUS contact information.
3.3.5
Other information
The icons on the top right side of the screen provide additional information
on the motherboard and the contents of the support CD.
3-6
Chapter 3: Starting up
3.4
Software information
Most of the applications in the support CD have wizards that will
conveniently guide you through the installation. View the online help or
readme file that came with the software for more information.
3.4.1
ASUS Instant Music
The motherboard is equipped with a BIOS-based audio playback feature
called I n s t a n t M u s i cc. The onboard audio AC’97 CODEC supports this
feature, which requires an optical drive (CD-ROM, DVD-ROM, or CD-RW).
•
Instant Music only supports CDs in audio format.
•
Instant Music does not work if you installed and enabled an add-on
sound card.
•
Instant Music only supports PS/2 keyboard.
To enable ASUS Instant Music:
1.
Connect the analog audio cable from the optical drive to the 4-pin CD
connector on the motherboard. See section “4.4 Connectors” for the
location of the CD connector.
Make sure to connect the optical drive audio cable. Otherwise, you
cannot control the audio volume using the Instant Music function keys.
2.
3.
4.
5.
Turn on the system and enter BIOS by pressing the D e l e t e key
during the Power On Self-Tests (POST).
In the I n s t a n t M u s i c C o n f i g u r a t i o n menu, select the item
I n s t a n t M u s i c and set it to E n a b l e d
d. See section “5.4.6 Instant
Music Configuration.”
The I n s t a n t M u s i c C D - R O M D r i v e item appears if you enabled
Instant Music. Highlight the item then press <Enter> to display the
CD-ROM options.
Save your changes and exit BIOS Setup. The hot key is <F10>.
•
The Scroll Lock LED is fixed to ON after enabling Instant Music.
•
The Caps Lock LED turns ON when you pause the CD playback.
•
When set to Instant Music mode, the system wake-up features
(LAN, keyboard, mouse, USB) are deactivated. In this case, power up
the system using the power switch.
•
If the system lost connection or did not detect any optical drive, the
Instant Music feature turns OFF (disabled) automatically. A “beep”
indicates this condition.
ASUS T2-AE1
3-7
To use ASUS Instant Music:
1.
Connect the PC power plug to an electrical outlet.
2.
Use either one of the two sets of special function keys on your
keyboard to play audio CDs. These keys only function as indicated if
you enabled the Instant Music item in BIOS.
Instant Music function keys (Set 1)
CD
ON/OFF
PLAY/PAUSE
Esc
F1
STOP/EJECT
PREVIOUS
NEXT
F3
F4
F2
VOL. DOWN
VOL. UP
F5
F6
F7
F8
To guide you in using Instant Music, place the Instant Music label over
the function keys on the keyboard. The Instant Music keyboard label
comes with your motherboard package.
Instant Music function keys (Set 2)
CAPS
LOCK
LED
CD ON/OFF
PLAY/PAUSE
STOP/EJECT
PREVIOUS
VOL. DOWN
SCROLL
LOCK
LED
NEXT
VOL. UP
3.
Connect the speakers to the Line Out (lime) port on the rear panel for
audio output. You may also connect a headphone to the headphone
port on the rear panel or on the optical drive front panel.
4.
Insert an audio CD to the optical drive.
5.
Press E s c to turn on Instant Music.
Press F 1 or the S p a c e B a r to play the first track on the audio CD.
6.
If there is no audio CD inside the optical drive, the drive tray ejects when
you press <F1> or <Space Bar>.
3-8
7.
Refer to the Instant Music keyboard label to select other tracks or
control the volume.
8.
Press <F2> or <Enter> once to stop playing the audio CD.
Press <F2> or <Enter> again to eject the CD.
Chapter 3: Starting up
3.4.2
ASUS Radio Player
ASUS Radio Player allows you to tune in to an FM station using the optional
radio module.
By default, the radio region of the ASUS FM radio module is set to
Europe
U S A or
e. If you purchased the barebone system outside Europe (U
Japan
n), you must change the radio region in the BIOS setup to receive
FM radio signals. See section “5.4.1 Instant Music Configuration” for
details.
Launching the ASUS Radio Player
To launch the ASUS Radio Player:
2.
Install the A S U S R a d i o A p p l i c a t i o n from the U t i l i t i e s tab of the
support CD. See page 3-4 for details.
After installing the application, click S t a r t > A l l P r o g r a m s > A S U S
> A S U S R a d i o P l a y e r V 1 . 0 > A S U S R a d i o P l a y e r V 1 . 0 from
the Windows® desktop.
3.
The ASUS Radio Player panel appears.
1.
Station frequency
Preset station list
Close ASUS Radio
Minimize ASUS Radio
Power button
Clock
Increase the volume
Decrease the volume
Mute/Sound on button
Store button
Edit button
Tune left
Scan left
ASUS T2-AE1
Stop
Tune right
Scan right
3-9
Storing a radio station
To store a radio station:
1.
2.
3.
Use the S c a n or T u n e
buttons to tune into a radio
station you wish to store.
Click the S t o r e button. A
S t o r e C h a n n e l window
appears.
Assign a C h a n n e l (preset
number) to the radio station
using the arrow buttons.
4.
Type the station name in the field, then click O K
K.
5.
The stored channel is displayed in the preset station list.
Editing a stored radio
To edit a stored radio station:
1.
Click the E d i t button. An
E d i t C h a n n e l window
appears.
2.
Select a radio station you
want to edit, then click the
E d i t button.
3.
Another E d i t C h a n n e l
window appears.
4.
Edit the station frequency and
name.
Click O K when you are done.
3-10
Chapter 3: Starting up
This chapter gives information
about the motherboard that comes
with the system. This chapter
includes the motherboard layout,
jumper settings, and connector
locations.
ASUS T2-AE1
Motherboard info
Chapter 4
4.1
Introduction
The ASUS Terminator 2 motherboard comes already installed in the ASUS
Terminator 2 system. This chapter provides technical information about the
motherboard for future upgrades or system reconfiguration.
4.2
Motherboard layout
24.89cm (9.8in)
IOC_MB
CPU_FAN
ALC655
AUX
USB12
FP_AUDIO
SPDIF_OUT
CD
CHA_FAN
ATXPWR
FLOPPY
SiS
760GX
USBPW12
USBPW34
20.06cm (7.9in)
Mic
In
Flash
BIOS
PRI_IDE
Line
In
DDR DIMM2 (64/72-bit, 184-pin module)
Socket 754
LPT
Line
Out
DDR DIMM1 (64/72-bit, 184-pin module)
VGA
Super
I/O
ATX12V
LCD_PANEL
KBMS
DJ_BTN
1394SEL
USB56
USB78
PCI
®
BUZZ
SB_PWR
SiS
965L
SATA2
AGP
VIA
VT6307
SATA1
RTL8201CL
CLRTC
BAT
LAN_USB34
PANEL
IE1394_0 IE1394_1
4-2
Chapter 4: Motherboard info
4.3
1.
Jumpers
Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The RAM
data in CMOS, that include system setup information such as system
passwords, is powered by the onboard button cell battery.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep
the cap on pins 2-3 for about 5-10 seconds, then move the cap
back to pins 1-2.
4. Re-install the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
CLRTC
®
Clear RTC RAM
2
1
Normal
(Default)
3
2
Clear CMOS
Except when clearing the RTC RAM, never remove the cap on CLRTC
jumper default position. Removing the cap will cause system boot failure.
ASUS T2-AE1
4-3
2.
USB device wake-up (3-pin USBPWR12, USBPWR34)
The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
Set these jumpers to +5V to wake up the computer from S1 sleep
mode (CPU stopped, DRAM refreshed, system running in low power
mode) using the connected USB devices. Set to +5VSB to wake up
from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh,
power supply in reduced power mode).
USBPW12
USBPW34
1 2
2 3
+5V
+5VSB
(Default)
®
USB device wake up
2.
•
The USB device wake-up feature requires a power supply that can
provide 500 mA on the +5VSB lead for each USB port; otherwise,
the system would not power up.
•
The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
1394 setting (3-pin 1394SEL)
Keep the default setting (1-2) to enable support for IEEE 1394a
devices. To disable, move the jumper caps to pins 2-3.
1394SEL
2 1
3 2
®
1394 setting
4-4
Enable
(Default)
Disable
Chapter 4: Motherboard info
4.4
Connectors
This section describes and illustrates the connectors on the motherboard.
See page 1-7 for the description of rear panel connectors.
1.
Front panel USB connector (10-1 pin USB56)
USB Power
USB5–
USB5+
GND
NC
The USB56 connector on the motherboard is for the USB_2 connector
on the front panel I/O daughterboard to support the USB 2.0 ports on
the front panel.
®
USB connector
10
2
9
BLINE_OUT_L
Front panel audio connector (10-1 pin FP_AUDIO)
This interface is for the FP_AUD connector on the front panel I/O
daughterboard to support the front panel audio I/O ports.
AGND
+5VA
BLINE_OUT_R
2.
1
USB Power
USB4-–
USB4+
GND
USB56
Front panel audio connector
ASUS T2-AE1
MIC2
MICPWR
Line out_R
NC
Line out_L
FP_AUDIO
®
4-5
3.
IEEE 1394a connectors (6-pin IE13
94_1, 8-pin IE1394_0)
394_1,
These connectors are for the IEEE 1394a connectors on the front
panel I/O daughterboard to support the front panel IEEE 1394a ports.
Connect the IE1394_0 motherboard connector to the 1394_1
daughterboard connector, and connect the IE1394_1 motherboard
connector to the 1394_2 daughterboard connector.
®
IEEE 1394 connectors
NEVER connect a U S B c a b l e to the IEEE 1394a connector. Doing so
will damage the motherboard!
4.
Digital audio connector (4-1 pin SPDIF_OUT)
(A) is for the SPDIF_OUT connector on the motherboard while (B) is
for the rear panel S/PDIF Out port.
SPDIF_OUT
GND
SPDIFOUT
®
Digital audio connector
4-6
+5V
A
B
Chapter 4: Motherboard info
5.
I/O extension module (22-pin IOC_MB)
This connector is for the CGAEX extension module. The CGAEX
extension module supports the rear panel GAME/MIDI and serial ports.
GAME
COM1
®
CGAEX
IOC_DC
®
IOC_MB connector
6.
CPU and chassis fan connectors (3-pin CPU_FAN,
3-pin CHA_FAN)
The fan connectors support the proprietary CPU fan and chassis fan.
Connect the fan cable to the connector matching the black wire to
the ground pin.
CPUFANIN
CPUFANPWR
GND
CPU_FAN
CHA_FAN
GND
CPUFANPWR
SYSFANIN
®
Fan connectors
Do not forget to connect the fan cables to the fan connectors. Lack of
sufficient air flow within the system may damage the motherboard
components. These are not jumpers! DO NOT place jumper caps on the
fan connectors!
ASUS T2-AE1
4-7
7.
ATX power connectors (20-pin ATXPWR, 4-pin ATX12V)
These connectors are for the 20-pin and 4-pin power plugs from the
power supply unit. The plugs from the power supply unit are designed
to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
ATX12V
GND
GND
+12V DC
+12.0VDC
+5VSB
PWR_OK
COM
+5.0VDC
COM
+5.0VDC
COM
+3.3VDC
+3.3VDC
®
ATX power connectors
8.
ATXPWR
+12V DC
+5.0VDC
+5.0VDC
-5.0VDC
COM
COM
COM
PS_ON#
COM
-12.0VDC
+3.3VDC
IDE connector (40-1 pin PRI_IDE)
The PRI_IDE connector is for the UltraATA100 IDE hard disk ribbon
cable. Connect the cable’s blue connector to the IDE connector, then
connect the gray connector to a slave device (optical drive) and the
black connector to the UltraATA100 master device (hard disk drive).
Refer to the hard disk documentation for the jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the UltraATA cable connector. This prevents incorrect orientation
when you connect the cables.
•
For Ultra ATA/133 IDE devices, use an 80-conductor IDE cable.
PRI_IDE
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
®
PIN 1
IDE connector
4-8
Chapter 4: Motherboard info
9.
Serial ATA connectors
(7-pin SATA1 [black], SATA2 [black])
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
SATA1
GND
TXP1
TXN1
GND
RXP1
RXN1
GND
SATA2
GND
TXP2
TXN2
GND
RXP2
RXN2
GND
®
SATA connectors
Important notes on Serial ATA
•
You must install Windows® 2000 Service Pack 4 or the Windows® XP
Service Pack 1 before using Serial ATA hard disk drives.
•
When using the connectors in S t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection
Connector
Color
Setting
Use
SATA1
Black
Master
Boot disk
SATA2
Black
Slave
Data disk
ASUS T2-AE1
4-9
1 0 . Internal audio connectors (4-pin AUX, CD)
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
Ground
Left Audio Channel
CD
Right Audio Channel
Internal audio connectors
Ground
Left Audio Channel
®
Right Audio Channel
AUX
1 1 . Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
FLOPPY
PIN 1
®
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
Floppy disk drive connector
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
4-10
Chapter 4: Motherboard info
1 2 . System panel connector (8-1 pin PANEL)
This connector accommodates several system front panel functions.
PWR
GND
RESET
PWR
PLED+
PLEDHDLED+
HDLED-
PANEL
PLED
HDLED
®
System panel connector
•
•
•
* Requires an ATX power supply.
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
Hard disk drive activity (2-pin HDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
Power/Soft-off button (2-pin PWR)
This connector is for the system power button. Pressing the power
button turns the system ON or puts the system in SLEEP or SOFT-OFF
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
ASUS T2-AE1
4-11
4-12
Chapter 4: Motherboard info
Chapter 5
BIOS setup
This chapter tells how to change
system settings through the BIOS
Setup menus and describes the
BIOS parameters.
ASUS T2-AE1
1
5.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1.
2.
3.
4.
A S U S A F U D O S (Updates the BIOS in DOS mode using a bootable
floppy disk.)
A S U S E Z F l a s h (Updates the BIOS using a floppy disk during POST.)
A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable
floppy disk or the motherboard support CD when the BIOS file fails or
gets corrupted.)
A S U S U p d a t e (Updates the BIOS in Windows® environment.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy
disk in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or AFUDOS utilities.
5.1.1
1.
Creating a bootable floppy disk
Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click S t a r t from the Windows® desktop, then select M y
C o m p u t e rr.
c. Select the 3 1/2 Floppy Drive icon.
d. Click F i l e from the menu, then select F o r m a tt. A F o r m a t 3 1 / 2
F l o p p y D i s k window appears.
e. Select C r e a t e a n M S - D O S s t a r t u p d i s k from the format
options field, then click S t a r tt.
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click S t a r tt, then select R u n
n.
5-2
Chapter 5: BIOS setup
d. From the Open field, type
D:\bootdisk\makeboot a:
assuming that D: is your optical drive.
e. Press <Enter>, then follow screen instructions to continue.
2.
Copy the original or the latest motherboard BIOS file to the bootable
floppy disk.
5.1.2
ASUS EZ Flash utility
The ASUS EZ Flash feature allows you to update the BIOS without having to
go through the long process of booting from a floppy disk and using a
DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is
accessible by pressing <Alt> + <F2> during the Power-On Self Tests
(POST).
To update the BIOS using EZ Flash:
1.
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for the motherboard and rename the same to K 8 S T . R O M
M.
2.
Save the BIOS file to a floppy disk, then restart the system.
3.
Press <Alt> + <F2> during POST to display the following.
EZFlash starting BIOS update
Checking for floppy...
4.
Insert the floppy disk that contains the BIOS file to the floppy disk
drive. When the correct BIOS file is found, EZ Flash performs the BIOS
update process and automatically reboots the system when done.
EZFlash starting BIOS update
Checking for floppy...
Floppy found!
Reading file “K8ST.ROM”. Completed.
Start erasing.......|
Start programming...|
Flashed successfully. Rebooting.
•
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
•
A “Floppy not found!” error message appears if there is no floppy
disk in the drive. A “K8ST.ROM not found!” error message appears if
the correct BIOS file is not found in the floppy disk. Make sure that
you rename the BIOS file to K8ST.ROM.
ASUS T2-AE1
5-3
5.1.3
AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment
using a bootable floppy disk with the updated BIOS file. This utility also
allows you to copy the current BIOS file that you can use as backup when
the BIOS fails or gets corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
•
Make sure that the floppy disk is not write-protected and has at
least 600 KB free space to save the file.
•
The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be exactly the same as shown.
1.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
2.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than
eight alphanumeric characters for the main filename and three
alphanumeric characters for the extension name.
A:\>afudos /oOLDBIOS1.ROM
Main filename
3.
Extension name
Press <Enter>. The utility copies the current BIOS file to the floppy
disk.
A:\>afudos /oOLDBIOS1.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
A:\>
The utility returns to the DOS prompt after copying the current BIOS
file.
5-4
Chapter 5: BIOS setup
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
Visit the ASUS website (www.asus.com) and download the latest BIOS
file for the motherboard. Save the BIOS file to a bootable floppy disk.
Write the BIOS filename on a piece of paper. You need to type the exact
BIOS filename at the DOS prompt.
2.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
3.
Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable
floppy disk.
A:\>afudos /iK8ST.ROM
4.
The utility reads the file and starts updating the BIOS.
A:\>afudos /iK8ST.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Search bootblock version
Advance Check........
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
ASUS T2-AE1
5-5
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iK8ST.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Search bootblock version
Advance Check.........
Erasing flash ..... done
Writing flash ..... done
Verifying flash ... done
Please restart your computer
A:\>
5.1.4
ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to
restore the BIOS file when it fails or gets corrupted during the updating
process. You can update a corrupted BIOS file using the motherboard
support CD or the floppy disk that contains the updated BIOS file.
•
Prepare the motherboard support CD or the floppy disk containing
the updated motherboard BIOS before using this utility.
•
Make sure that you rename the original or updated BIOS file in the
floppy disk to K 8 S T . R O M
M.
Recovering the BIOS from a floppy disk
To recover the BIOS from a floppy disk:
5-6
1.
Turn on the system.
2.
Insert the floppy disk with the original or updated BIOS file to the
floppy disk drive.
Chapter 5: BIOS setup
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and starts flashing the
corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “K8ST.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1.
Remove any floppy disk from the floppy disk drive, then turn on the
system.
2.
Insert the support CD to the optical drive.
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the
optical drive for the original or updated BIOS file. The utility then
updates the corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
Reading file “K8ST.ROM”. Completed.
Start flashing...
ASUS T2-AE1
5-7
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
The recovered BIOS may not be the latest BIOS version for this
motherboard. Visit the ASUS website (www.asus.com) to download the
latest BIOS file.
5.1.5
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update
the motherboard BIOS in Windows® environment. The ASUS Update utility
allows you to:
•
Save the current BIOS file
•
Download the latest BIOS file from the Internet
•
Update the BIOS from an updated BIOS file
•
Update the BIOS directly from the Internet, and
•
View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
2.
Place the support CD in the optical drive. The D r i v e r s menu appears.
Click the U t i l i t i e s tab, then click I n s t a l l A S U S U p d a t e
VX.XX.XX
X. See page 3-4 for the U t i l i t i e s screen menu.
3.
The ASUS Update utility is copied to your system.
1.
Quit all Windows® applications before you update the BIOS using this
utility.
5-8
Chapter 5: BIOS setup
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1.
Launch the ASUS Update utility from the Windows® desktop by clicking
Start > Programs > ASUS > ASUSUpdate > ASUSUpdate
e. The
ASUS Update main window appears.
2.
Select U p d a t e B I O S f r o m
t h e I n t e r n e t option from the
drop-down menu, then click
N e x tt.
ASUS T2-AE1
3.
Select the ASUS FTP site
nearest you to avoid network
traffic, or click A u t o S e l e c tt.
Click N e x tt.
5-9
4.
From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5.
Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1.
2.
3.
4.
5-10
Launch the ASUS Update utility from the Windows® desktop by
clicking S t a r t > P r o g r a m s > A S U S > A S U S U p d a t e >
ASUSUpdate
e. The ASUS Update main window appears.
Select U p d a t e B I O S f r o m a
f i l e option from the drop-down
menu, then click N e x tt.
Locate the BIOS file from the
e.
O p e n window, then click S a v e
Follow the screen instructions to
complete the update process.
Chapter 5: BIOS setup
5.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can
update using the provided utility described in section “5.1 Managing and
updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup.” This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change
the configuration of your computer in the future. For example, you can
enable the security password feature or change the power management
settings. This requires you to reconfigure your system using the BIOS
Setup program so that the computer can recognize these changes and
record them in the CMOS RAM of the firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you
start up the computer, the system provides you with the opportunity to
run this program. Press <Del> during the Power-On-Self-Test (POST) to
enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>. You can also restart by turning the system off and then
back on. Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being
a menu-driven program, it lets you scroll through the various sub-menus
and make your selections from the available options using the navigation
keys.
•
The default BIOS settings for this motherboard apply for most
conditions to ensure optimum performance. If the system becomes
unstable after changing any BIOS settings, load the default settings
to ensure system compatibility and stability. Select the L o a d
D e f a u l t S e t t i n g s item under the Exit Menu. See section “5.7 Exit
Menu.”
•
The BIOS setup screens shown in this section are for reference
purposes only, and may not exactly match what you see on your
screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for this motherboard.
ASUS T2-AE1
5-11
5.2.1
BIOS menu screen
Menu items
Menu bar
Configuration fields
General help
System Time
System Date
Legacy Diskette A
[16:37:21]
[Thu,01/06/2005]
[1.44M, 3.5 in.]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Primary IDE Master
:
Primary IDE Slave
:
Onboard PCI S-ATA Controller :
[ST320410A]
[ASUS CD-S520/A]
[Disabled]
Use [+] or [-] to
configure the System
time.
System Information
Sub-menu items
5.2.2
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
Advanced
For changing the basic system configuration
For changing the advanced system settings
Power
For changing the advanced power management (APM)
configuration
Boot
Exit
For changing the system boot configuration
For selecting the exit options and loading default
settings
To select an item on the menu bar, press the right or left arrow key on the
keyboard until the desired item is highlighted.
5.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for
that particular menu. Use the navigation keys to select items in the menu
and change the settings.
Some of the navigation keys differ from one screen to another.
5-12
Chapter 5: BIOS setup
5.2.4
Menu items
The highlighted item on the menu
bar displays the specific items for
that menu. For example, selecting
M a i n shows the Main menu items.
The other items (Advanced, Power,
Boot, and Exit) on the menu bar
have their respective menu items.
5.2.5
System Time
System Date
Legacy Diskette A
[16:37:21]
[Thu,01/05/2005]
[1.44M, 3.5 in]
Primary IDE Master
: [ST320410A]
Primary IDE Slave
: [ASUS CD-S520/A]
Onboard PCI S-ATA controller [Disabled]
System Information
Main menu items
Sub-menu items
A solid triangle before each item on any menu screen means that the item
has a sub-menu. To display the sub-menu, select the item and press
<Enter>.
5.2.6
Configuration fields
These fields show the values for the menu items. If an item is
user-configurable, you can change the value of the field opposite the item.
You cannot select an item that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when
selected. To change the value of a field, select it then press <Enter> to
display a list of options. Refer to “5.2.7 Pop-up window.”
5.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with
the configuration options for that item.
5.2.8
Scroll bar
A scroll bar appears on the right side
of a menu screen when there are
items that do not fit on the screen.
Press the Up/Down arrow keys or
<Page Up> /<Page Down> keys to
display the other items on the
screen.
5.2.9
General help
At the top right corner of the menu
screen is a brief description of the
selected item.
ASUS T2-AE1
Advanced PCI/PnP Settings
WARNING: Setting wrong values in
below sections may cause system to
malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
[No]
[64]
[Yes]
[Disabled]
[Enabled]
Pop-up window
Scroll bar
5-13
5.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears,
giving you an overview of the basic system information.
Refer to section “5.2.1 BIOS menu screen” for information on the menu
screen items and how to navigate through them.
System Time
System Date
Legacy Diskette A
[16:37:21]
[Thu,01/06/2005]
[1.44M, 3.5 in.]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Primary IDE Master
:
Primary IDE Slave
:
Onboard PCI S-ATA Controller :
[ST320410A]
[ASUS CD-S520/A]
[RAID By ROM]
Use [+] or [-] to
configure the System
time.
System Information
5.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
5.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
5.3.3
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
5-14
Chapter 5: BIOS setup
5.3.4
Primary IDE Master/Slave
While entering Setup, the BIOS automatically detects the presence of IDE
devices. There is a separate sub-menu for each IDE device. Select a device
item then press <Enter> to display the IDE device information.
Primary IDE Master
Device
Vendor
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
SMART Monitoring
:
:
:
:
:
:
:
:
:
Hard Disk
ST320410A
20.0GB
Supported
16 Sectors
4
MultiWord DMA-2
Ultra DMA-5
Supported
Select the type of
device connected to
the system.
Type
[Auto]
LBA/Large Mode
[Auto]
Block(Multi-sector Transfer) M [Auto]
PIO Mode
[Auto]
DMA Mode
[Auto]
SMART Monitoring
[Auto]
32Bit Data Transfer
[Disabled]
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and SMART monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to Auto allows automatic selection of
the appropriate IDE device type. Select CDROM if you are specifically
configuring a CD-ROM drive. Select ARMD (ATAPI Removable Media Device)
if your device is either a ZIP, LS-120, or MO drive. Configuration options:
[Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to Auto enables the LBA mode if
the device supports this mode, and if the device was not previously
formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Block (Multi-sector Transfer) [Auto]
Enables or disables data multi-sectors transfers. When set to Auto, the
data transfer from and to the device occurs multiple sectors at a time if
the device supports multi-sector transfer feature. When set to [Disabled],
the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
ASUS T2-AE1
5-15
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0]
[SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0]
[UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Disabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
5.3.5
Onboard PCI S-ATA Controller [RAID By ROM]
Allows you to disable the onboard PC Serial ATA controller, or choose its
function from the available options. Configuration options: [Disabled] [IDE
By BIOS] [RAID By ROM]
5-16
Chapter 5: BIOS setup
5.3.6
System Information
This menu gives you an overview of the general system specifications. The
BIOS automatically detects the items in this menu.
AMIBIOS
Version
: 0117
Build Date : 02/21/05
Processor
Type
Speed
Count
: AMD Athlon (tm) 64 Processor 3200+
: 2000 MHz
: 1
System Memory
Size
: 224 MB
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
ASUS T2-AE1
5-17
5.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU
and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values can cause the system to malfunction.
CPU Configuration
Chipset
Onboard Devices Configuration
PCI PnP
Instant Music Configuration
5.4.1
CPU Configuration
CPU Configuration
Cool ‘n’ Quiet
Memory Configuration
[Enabled]
Select Manual or
Standard for
Overclocking
Cool ‘n’ Quiet [Enabled]
Allows you to enable or disable the AMD Cool ‘n’ Quiet!™ technology
feature. Configuration options: [Disabled] [Enabled]
5-18
Chapter 5: BIOS setup
Memory Configuration
CPU Configuration
Burst length
Memclock Mode
Memory CLK
CAS Latency
TRCD
TRP
TRAS
[4 Beats]
[Auto]
Burst length can be
set to 8 or 4 beats.
64 -bit Dq must use
the 4 beats.
: 200 MHz
: 3.0
: 3CLK
: 3CLK
: 8CLK
Burst length [4 Beats]
Sets the burst length.
Configuration options: [8 Beats] [4 Beats] [2 Beats]
Memclock Mode [Auto]
[Auto] allows the BIOS to set the memclock mode automatically.
[Limit] allows you to select from any of the standard values.
Configuration options: [Auto] [Limit]
The following item appears when the M e m c l o c k M o d e item is set to
[Limit]
Memclock Value [100 MHz]
Allows you to set the memclock value.
Configuration options: [100 MHz] [133 MHz] [166 MHz] [183 MHz]
[200 MHz] [216 MHz] [233 MHz] [250 MHz]
ASUS T2-AE1
5-19
5.4.2
Chipset
Options for AGP
configuration.
Chipset Settings
AGP Configuration
Hyper Transport Configuration
MPS Configuration
AGP Configuration
AGP Configuration
Aperture Size
Graphic Adapter Priority
AGP FAST WRITE
Select AGP 3.0 Data Ratio
Share Memory
[64 MB]
[AGP/Int-VGA]
[Disabled]
[8x]
[ 32 MB]
The size of mapped
memory for AGP graphic
data.
Aperture Size [64 MB]
Configuration options: [32 MB] [64 MB] 128 MB]
Graphic Adapter Priority [AGP/Int-VGA]
Allows selection of the graphics controller to use as a primary boot
device. Configuration options: [Internal VGA] [AGP/Int-VGA]
[AGP/PCI] [PCI/AGP] [PCI/Int-VGA]
AGP FAST WRITE [Disabled]
Configuration options: [Disabled] [Enabled]
Select AGP 3.0 Data Ratio [8x]
Configuration options: [8x] [4x]
Share Memory [32 MB]
Configuration options: [32 MB] [64 MB] 128 MB]
5-20
Chapter 5: BIOS setup
HyperTransport Configuration
Host Link_width_out
x Link_width_in
HyperTransport Configuration
HT Width
HT Speed
[ 8x16 BIT]
[800 MHz]
HT Width [ 8x16 BIT]
Configuration options: [8x8 BIT] [16x16 BIT] [16x8 BIT] [8x16 BIT]
HT Speed [800 MHz]
Configuration options: [200 MHz] [400 MHz] [600 MHz] [800 MHz]
MPS Configuration
Select MPS Revision
MPS Configuration
MPS Revision
[1.4]
MPS Revision [1.4]
Configuration options: [1.1] [1.4]
ASUS T2-AE1
5-21
5.4.3
Onboard Devices Configuration
Onboard AC97 Audio Device
Onboard SiS190 LAN Device
SiS190 LAN Boot ROM
USB Configuration
[Enabled]
[Enabled]
[Disabled]
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
ECP Mode DMA Channel
Parallel Port IRQ
Onboard Game/MIDI Port
[3F8/IRQ4]
[378]
[ECP]
[DMA3]
[IRQ7]
[Disabled]
Onboard AC97 Audio Device [Enabled]
Enables or disables the AC’97 CODEC.
Configuration options: [Enabled] [Disabled]
OnBoard SiS190 LAN Device [Enabled]
Allows you to enable or disable the onboard SiS190 LAN controller.
Configuration options: [Enabled] [Disabled]
SiS190 LAN Boot ROM [Disabled]
Allows you to enable or disable the boot ROM in the onboard LAN
controller. Configuration options: [Disabled] [Enabled]
5-22
Chapter 5: BIOS setup
USB Configuration
The items in this menu allow you to change the USB-related features.
Select an item then press <Enter> to display the configuration options.
Enables USB host
controllers.
USB Configuration
USB Devices Enabled: None
Onboard SiS USB1.1 Device
Onboard SiS USB2.0 Device
Legacy USB Support
USB 2.0 Controller Mode
Stop EHCI HC in OHCI handover
[Enabled]
[Enabled]
[Auto]
[HiSpeed]
[Enabled]
The U S B D e v i c e s E n a b l e d item shows the auto-detected values. If
no USB device is detected, the item shows N o n e
e.
Onboard SiS USB1.1 Device [Enabled]
Allows you to enable or disable the onboard SiS USB 1.1 controller.
Configuration options: [Enabled] [Disabled]
Onboard SiS USB2.0 Device [Enabled]
Allows you to enable or disable the onboard SiS USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
Legacy USB Support [Auto]
Allows you to enable or disable support for USB devices on legacy
operating systems (OS). Setting to Auto allows the system to detect the
presence of USB devices at startup. If detected, the USB controller legacy
mode is enabled. If no USB device is detected, the legacy USB support is
disabled. Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed ] [HiSpeed ]
Stop EHCI HC in OHCI handover [Enabled]
Allows you to enable or disable the enhanced host controller interface
(EHCI) hand-off support. Configuration options: [Disabled] [Enabled]
ASUS T2-AE1
5-23
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4]
[2E8/IRQ3]
Parallel Port Address [378]
Allows you to select the Parallel Port base addresses.
Configuration options: [Disabled] [378] [278] [3BC]
Parallel Port Mode [ECP]
Allows you to select the Parallel Port mode.
Configuration options: [Normal] [Bi-directional] [EPP] [ECP]
ECP Mode DMA Channel [DMA3]
Appears only when the P a r a l l e l P o r t M o d e is set to [ECP]. This
item allows you to set the Parallel Port ECP DMA.
Configuration options: [DMA0] [DMA1] [DMA3]
EPP Version [1.9]
Allows selection of the Parallel Port EPP version. This item appears
only when the P a r a l l e l P o r t M o d e is set to [EPP].
Configuration options: [1.9] [1.7]
Parallel Port IRQ [IRQ7]
Allows selection of the Parallel Port IRQ.
Configuration options: [IRQ5] [IRQ7]
Onboard Game/MIDI Port [Disabled]
Allows you to select the Game Port adderss or to disable the port.
Configuration options: [Disabled] [200/300] [200/330] [208/300]
[208/330]
5-24
Chapter 5: BIOS setup
5.4.4
PCI PnP
The PCI PnP menu items allow you to change the advanced settings for
PCI/PnP devices. The menu includes setting IRQ and DMA channel resources
for either PCI/PnP or legacy ISA devices, and setting the memory size block
for legacy ISA devices.
Take caution when changing the settings of the PCI PnP menu items.
Incorrect field values can cause the system to malfunction.
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
Offboard PCI/ISA IDE Card
[No]
[64]
[Yes]
[Disabled]
[Enabled]
[Auto]
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[PCI
[PCI
[PCI
[PCI
[PCI
[PCI
[PCI
[PCI
[PCI
No: Lets the BIOS
configure all the
devices in the system.
Yes: Lets the operating
system configure Plug
and Play (PnP) devices
not required for boot
if your system has a
Plug and Play operating
system.
Device]
Device]
Device]
Device]
Device]
Device]
Device]
Device]
Device]
Plug and Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set
to [Yes] and if you install a Plug and Play operating system, the operating
system configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
PCI Latency Timer [64]
Allows you to select the value in units of PCI clocks for the PCI device
latency timer register. Configuration options: [32] [64] [96] [128] [160]
[192] [224] [248]
Allocate IRQ to PCI VGA [Yes]
When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card
requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the
PCI VGA card even if requested. Configuration options: [Yes] [No]
Palette Snooping [Disabled]
When set to [Enabled], the palette snooping feature informs the PCI
devices that an ISA graphics device is installed in the system so that the
latter can function correctly. Configuration options: [Disabled] [Enabled]
ASUS T2-AE1
5-25
PCI IDE BusMaster [Enabled]
Allows BIOS to use PCI bus mastering when reading/writing to IDE devices.
Configuration options: [Disabled] [Enabled]
OffBoard PCI/ISA IDE Card [Auto]
Allows you to set the PCI slot number holding a PCI IDE card that requires
you to set the slot number. Configuration options: [Auto] [PCI Slot1]
[PCI Slot2] [PCI Slot3] [PCI Slot4] [PCI Slot5] [PCI Slot6 ]
IRQ-xx assigned to [PCI Device]
When set to [PCI Device], the specific IRQ is free for use of PCI/PnP
devices. When set to [Reserved], the IRQ is reserved for legacy ISA
devices. Configuration options: [PCI Device] [Reserved]
5-26
Chapter 5: BIOS setup
5.4.5
Instant Music Configuration
Instant Music Option
Instant Music
[Disabled]
If enabled, power up
by PS/2 keyboard will
be disabled.
Instant Music [Disabled]
Enables or disables the Instant Music feature. Setting this item to [Enabled]
disables the power up by PS/2 keyboard function.
Configuration options: [Disabled] [Enabled]
The following item appears when the I n s t a n t M u s i c item is set to
[Enabled].
Instant Music CD-ROM drive [IDE Primary Slave]
Allows you to configure the Instant Music CD-ROM selection.
Configuration options: [IDE Primary Master] [IDE Primary Slave]
ASUS T2-AE1
5-27
5.5
Power menu
The Power menu items allow you to change the settings for the ACPI and
Advanced Power Management (APM). Select an item then press <Enter> to
display the configuration options.
Suspend Mode
Repost Video on S3 Resume
ACPI 2.0 Support
ACPI APIC Support
[S1 & S3 (STR)]
[No]
[No]
[Enabled]
Select the ACPI state
used for System
Suspend.
APM Configuration
Hardware Monitor
5.5.1
Suspend Mode [S1 & S3 (STR)]
Allows you to select the Advanced Configuration and Power Interface
(ACPI) state to be used for system suspend.
Configuration options: [S1 (POS) Only] [S1 & S3 (STR)] [S3 Only]
5.5.2
Repost Video on S3 Resume [No]
Determines whether to invoke VGA BIOS POST on S3/STR resume.
Configuration options: [No] [Yes]
5.5.3
ACPI 2.0 Support [No]
Allows you to add more tables for Advanced Configuration and Power
Interface (ACPI) 2.0 specifications. Configuration options: [No] [Yes]
5.5.4
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power
Interface (ACPI) support in the Advanced Programmable Interrupt
Controller (APIC). When set to Enabled, the ACPI APIC table pointer is
included in the RSDT pointer list. Configuration options: [Disabled]
[Enabled]
5-28
Chapter 5: BIOS setup
5.5.5
APM Configuration
APM Configuration
Power Button Mode
Restore on AC Power Loss
Resume on Ring
Resume on LAN
Resume on PME#
Resume On Keyboard
Resume PS/2 Mouse
Resume On RTC
[On/Off]
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Go into On/Off or
Suspend when Power
button is pressed.
Power Button Mode [On/Off]
Allows the system to go into On/Off mode or suspend mode when the
power button is pressed. Configuration options: [On/Off] [Suspend]
Restore on AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power
loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state,
whatever the system state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Resume on Ring [Disabled]
Allows you to enable or disable RI to generate a wake event.
Configuration options: [Disabled] [Enabled]
Resume on LAN [Disabled]
Allows you to enable or disable the LAN GPI to generate a wake event.
Configuration options: [Disabled] [Enabled]
Resume on PME#[Disabled]
Allows you to enable or disable the PME to generate a wake event.
Configuration options: [Disabled] [Enabled]
Resume on Keyboard [Disabled]
Allows you to use specific keys on the keyboard to turn on the system.
This feature requires an ATX power supply that provides at least 1A on the
+5VSB lead. Configuration options: [Disabled] [Enabled]
ASUS T2-AE1
5-29
Resume on PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]
Resume on RTC [Disabled]
Allows you to enable or disable RTC event to wake the system after a
power failure. Configuration options: [Disabled] [Enabled]
5.5.6
Hardware Monitor
Hardware Monitor
CPU Temperature
CPU Temperature
MB Temperature
[51ºC/122.5ºF]
[41ºC/105.5ºF]
CPU Fan Speed
CPU Q-Fan Control
CPU Q-Fan Mode
CPU Q-Fan Ratio
Chassis Fan Speed
Chassis Q-Fan Control
Chassis Fan Ratio
[3813 RPM]
[Enabled]
[PWM]
[Auto]
[N/A]
[Enabled]
[Auto]
VCORE Voltage
3.3V Voltage
5V Voltage
12V Voltage
[ 1.320V]
[ 3.345V]
[ 5.094V]
[11.880V]
CPU Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the
motherboard and CPU temperatures. Select Disabled if you do not wish to
display the detected temperatures.
CPU Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A.
5-30
Chapter 5: BIOS setup
CPU Q-Fan Control [Enabled]
Allows you to enable or disable the ASUS Q-Fan feature that smartly
adjusts the fan speeds for more efficient system operation. When this field
is set to [Enabled], the three succeeding items appear. Configuration
options: [Disabled] [Enabled]
The C P U Q - F a n M o d e and C P U Q - F a n R a t i o items appear only
when the C P U Q - F a n C o n t r o l is set to [Enabled]
CPU Q-Fan Mode [PWM]
Allows you to select the type of CPU fan cable connected to the CPU fan
connector. Set to [PWM] when using a 4-pin CPU fan cable. Set to [DC]
when using a 3-pin CPU fan cable. Configuration options: [PWM] [DC]
CPU Q-Fan Ratio [Auto]
Allows you to select the appropriate CPU fan speed ratio for the system.
The default [Auto] automatically selects the fan speed ratio when
operating a low CPU temperature. Select a higher ratio if you installed
additional devices and the system requires more ventilation. Configuration
options: [Auto] [90%] [80%] [70%] [60%]
Chassis Fan Speed [Ignored] or [N/A]
The onboard hardware monitor automatically detects and displays the
chassis fan speed in rotations per minute (RPM). If the fan is not connected
to the chassis, the specific field shows N/A.
Chassis Q-Fan Control [Enabled]
Allows you to enable or disable the chassis Q-Fan feature that smartly
adjusts the fan speeds for more efficient system operation.
Configuration options: [Disabled] [Enabled]
Chassis Fan Ratio [Auto]
This item appears only when the Chassis Q-Fan Control item is set to
[Enabled]. This allows you to select the appropriate chassis fan speed ratio
for the system. The default [Auto] automatically selects the fan speed
ratio when operating a low CPU temperature. Select a higher ratio if you
installed additional devices and the system requires more ventilation.
Configuration options: [Auto] [90%] [80%] [70%] [60%]
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output
through the onboard voltage regulators.
ASUS T2-AE1
5-31
5.6
Boot menu
The Boot menu items allow you to change the system boot options. Select
an item then press <Enter> to display the sub-menu.
Boot Settings
Specifies the Boot
Device Boot Priority
sequence.
Boot Device Priority
Boot Settings Configuration
Security
5.6.1
Boot Device Priority
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[PM-ST320410A]
[PS-ASUS CD-S520/A]
Specifies the boot
sequence from the
availabe devices.
1st ~ xxth Boot Device [1st Floppy Drive]
These items specify the boot device priority sequence from the available
devices. The number of device items that appears on the screen depends
on the number of devices installed in the system.
Configuration options: [xxxxx Drive] [Disabled]
5-32
Chapter 5: BIOS setup
5.6.2
Boot Settings Configuration
Boot Settings Configuration
Quick Boot
Full Screen Logo
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait For ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Au to]
[Enabled]
[Enabled]
[Disabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST)
while booting to decrease the time needed to boot the system. When set
to [Disabled], BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo™ feature.
Add On ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
PS/2 Mouse Support [Auto]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto]
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when
error occurs. Configuration options: [Disabled] [Enabled]
ASUS T2-AE1
5-33
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run
Setup” during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap
Interrupt 19. Configuration options: [Disabled] [Enabled]
5.6.3
Security
The Security menu items allow you to change the system security settings.
Select an item then press <Enter> to display the configuration options.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
<Enter> to change
password.
<Enter> again to
disabled password.
Change Supervisor Password
Boot Sector Virus Protection
[Disabled]
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default N o t I n s t a l l e d
d.
After you set a password, this item shows I n s t a l l e d
d.
To set a Supervisor Password:
1.
Select the Change Supervisor Password item and press <Enter>.
2.
From the password box, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a
user password.
To clear the supervisor password, select the Change Supervisor Password
then press <Enter>. The message “Password Uninstalled” appears.
5-34
Chapter 5: BIOS setup
If you forget your BIOS password, you can clear it by erasing the CMOS
Real Time Clock (RTC) RAM. See section “4.3 Jumpers” for information
on how to erase the RTC RAM.
After you have set a supervisor password, the other items appear to allow
you to change other security settings.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
Boot Sector Virus Protection
<Enter> to change
password.
<Enter> again to
disabled password.
[Full Access]
[Setup]
[Disabled]
User Access Level (Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
N o A c c e s s prevents user access to the Setup utility.
V i e w O n l y allows access but does not allow change to any field.
L i m i t e d allows changes only to selected fields, such as Date and
Time.
F u l l A c c e s s allows viewing and changing all the fields in the Setup
utility.
Change User Password
Select this item to set or change the user password. The User Password
item on top of the screen shows the default N o t I n s t a l l e d
d. After you set
a password, this item shows I n s t a l l e d
d.
To set a User Password:
1.
Select the Change User Password item and press <Enter>.
2.
On the password box that appears, type a password composed of at
least six letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
ASUS T2-AE1
5-35
The message “Password Installed” appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user
password.
Clear User Password
Select this item to clear the user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the
Setup utility. When set to [Always], BIOS checks for user password both
when accessing Setup and booting the system.
Configuration options: [Setup] [Always]
Boot Sector Virus Protection [Disabled]
Allows you to enable or disable the boot sector virus protection.
Configuration options: [Disabled] [Enabled]
5.7
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values
for the BIOS items, and save or discard your changes to the BIOS items.
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Exit system setup
after saving the
changes.
F10 key can be used
for this operation.
Load Setup Defaults
Pressing <Esc> does not immediately exit this menu. Select one of the
options from this menu or <F10> from the legend bar to exit.
5-36
Chapter 5: BIOS setup
Exit & Save Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
An onboard backup battery sustains the CMOS RAM so it stays on even
when the PC is turned off. When you select this option, a confirmation
window appears. Select Y e s to save changes and exit.
If you attempt to exit the Setup program without saving your changes,
the program prompts you with a message asking if you want to save
your changes before exiting. Press <Enter> to save the changes while
exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you
made to the Setup program. If you made changes to fields other than
System Date, System Time, and Password, the BIOS asks for a confirmation
before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation appears.
Select Y e s to discard any changes and load the previously saved values.
Load Setup Defaults
This option allows you to load the default values for each of the
parameters on the Setup menus. When you select this option or if you
press <F5>, a confirmation window appears. Select Y e s to load default
values. Select E x i t & S a v e C h a n g e s or make other changes before
saving the values to the non-volatile RAM.
ASUS T2-AE1
5-37
5-38
Chapter 5: BIOS setup
Appendix
Appendix
The Appendix includes the power
supply unit specification for this
system.
ASUS T2-AE1
Power supply specifications
Input characteristics
Input Voltage Range
Min
Nom
Max
Range 1
90 V
115 V
132 V
Range 2
180 V
230 V
264 V
Input Frequency Range
47 Hz to 63 Hz
Maximum Input AC Current
5 A max. at 115 Vac
3 A max. at 230 Vac, full load
Inrush Current
No hazards to occur and damage
components
Efficiency
65% min. at 115Vac and output
full load
Current Harmonic
Meets EN61000-3-2 @ 100 Vac/50 Hz
or 230 Vac/50 Hz at full load
EPA
50% min. at input 115 Vac, 60 Hz
Output characteristics
Output
Load Range
Regulation
Ripple
Voltage
Min
Max
Min
Max
Max
+5 V
1.5 A
21 A
-5%
+5%
50 mVp-p
+12 V
0.5 A
10 A
-5%
+5%
120 mVp-p
-12 V
0.05 A
0.8 A
-10%
+10%
150 mVp-p
+3.3 V
0.3 A
14 A
-5%
+5%
60 mVp-p
+5 VSB
0.01 A
2A
-5%
+5%
60 mVp-p
Over-Voltage Protection (OVP)
Output Voltage
A-2
Maximum Voltage
+3.3V
4.6V
+5V
6.5V
+12V
15.6V
Appendix
">