Aube Technologies TH110 User's Manual

Aube Technologies TH110 User's Manual
TH110
User Guide
Programmable Thermostat
n
1.
Description
Aube’s TH110 programmable thermostat can be connected to an electric
heating system such as an electric baseboard, a radiant ceiling, a floor heating system, an electric convector, etc. It is not compatible with a central heating system.
p
The configuration switches are on the back of the thermostat. Default (factory)
settings are inside the gray cells.
#
Time and day
On/Standby
switch
Preset temperature
icons
Heating
indicator
To set the day
Periods
To set the time
Temperature
adjustment
*
2.
Connection
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN POWER
PANEL TO AVOID ELECTRICAL SHOCK.
•
The installation must be carried out by an electrician.
•
All cables and connections must conform to the local electrical code.
•
Special CO/ALR solderless connectors must be used when connecting
with aluminum conductors.
•
Install the thermostat onto an electrical box.
•
Install the thermostat about 5 feet high, on an inside wall facing the
heater.
•
Avoid locations where there are air drafts (such as the top of a staircase
or an air outlet), dead air spots (such as behind a door), or direct sunlight.
•
Do not install the thermostat on a wall that conceals chimney or stove
pipes.
n
Connect the thermostat wires to the
240 V line and to the load using solderless connectors for copper wires.
o
Push the excess wire back into the
electrical box to prevent interference
with the thermostat.
p
q
Secure the thermostat using two 6-32
screws.
Return power to heating system.
NOTE: Always keep the thermostat's vents
clean and unobstructed.
TH110
Power
B
R
Disable
Enable
SW3
Early Start a
Time format
12-hour
24-hour
SW4
Temperature format b
°F
°C
4.
Power-up
) and displays the
Press the Hour and Min buttons to set the thermostat’s clock.
Press the Day button to set the day.
r
5.
Temperature Setting
Setpoint
The thermostat normally displays the actual temperature. To view the setpoint, press the
or
button briefly. The setpoint will appear for the next 5
seconds.
To change the setpoint, press the
or button until the desired temperature
is displayed. To scroll faster, hold the button.
Using a preset temperature
The thermostat has 3 preset temperatures:
Comfort temperature
Economy temperature
Vacation temperature
Icon
Intended use
Default setting
Comfort (when at home)
21°C (70°F)
Economy (when asleep or away from home)
16°C (62°F)
Vacation (during prolonged absence)
10°C (50°F)
•
To use the Comfort or Economy temperature, press the
respectively. The corresponding icon will be displayed.
•
To use the Vacation temperature, press both
neously. The
icon will be displayed.
and
or
button
buttons simulta-
Storing a preset temperature
To store the Comfort or Economy temperature:
B
B
R
60 HZ
Not used
SW2
n
o
To select the
operating mode
240 VAC
DN
Upon power-up, the thermostat is in manual mode (
actual temperature.
To skip a period
Set the switch to Standby to cut power to the heater. This will not affect the time
and temperature settings.
o
UP
SW1
q
To program the schedule
Temperature
preset buttons
Configurations
a. Early Start can be used in Automatic mode only. When this function is
enabled, the thermostat calculates the optimal time to start heating in
order to obtain the desired temperature by the set time. The thermostat
re-assesses the start time daily based on the previous day’s performance.
b. If you change the temperature display format, the preset temperatures
( , and ) will return to their default settings.
Appears during the
setpoint display
Temperature
Operating
mode icons
3.
Configuration
R
B
R
Load
Set the desired temperature using the
or button. Press and hold
the appropriate button (
or ) for approximately 3 seconds until the
corresponding icon is displayed. Press the Mode button.
To store the Vacation temperature:
Set the desired temperature using the
or button. Press and hold
both
and
buttons simultaneously for approximately 3 seconds
until the
icon is displayed. Press the Mode button.
400-110-000-A
2/6/05
1/2
s
6.
Operating Modes
Automatic - The temperature is set according to the energy-saving
schedule. To place the thermostat in this mode, press Mode until
is displayed. The icons of the current period and preset temperature are also displayed.
Temporary Bypass: If you modify the setpoint (by pressing the , ,
or
button) when the thermostat is in automatic mode, the new setpoint will be used until the end of the current period. When the next
period starts, the temperature set for that period becomes the new setpoint.
Manual - The energy-saving schedule is not used. The temperature must
be set manually. To place the thermostat in this mode:
n
o
Press Mode until
is displayed.
Set the temperature using the
,
,
or
button.
Vacation - The thermostat is set to the Vacation temperature. Press
both
mode.
t
and
buttons simultaneously to place the thermostat in Vacation
7.
Energy-saving Schedule
The schedule consists of 4 periods per day which represents a typical week
day. You can program the thermostat to skip the periods that do not apply to
your situation. For example, you can skip periods 2 and 3 for the weekend.
Period
Description
Associated preset temperature
Wake-up
Away from home
Return home
Sleep
The Comfort ( ) temperature is used in periods 1 and 3 and the Economy
( ) temperature is used in periods 2 and 4. For example, when the period
changes from 1 to 2, the setpoint automatically changes from Comfort setting
( ) to Economy setting ( ).
You can have a different program for each day of the week; i.e., each period
can start at different time for each day of the week. The thermostat has been
programmed with the following schedule.
Period
Setting
MO
TU
WE
TH
FR
SA
SU
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
--:--
--:--
6:00
PM
6:00
PM
6:00
PM
6:00
PM
6:00
PM
--:--
--:--
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
u
8.
Troubleshooting
Problems
Solutions
The thermostat’s screen is blank.
The thermostat’s switch is on Standby.
LO is displayed.
The measured temperature is below 0°C
(32°F). Heating is activated.
HI is displayed.
The measured temperature is above 50°C
(122°F).
The wrong time is displayed.
The thermostat was without power for
more than 2 hours.
The measured temperature is wrong.
The thermostat is located in a spot
exposed to an air draft.
The heater is always On.
Bad installation
The thermostat indicates that heating is On
Bad installation
but the heater is not On.
Check that the thermostat is in Automatic
The temperature does not change accordmode. Check also the energy-saving
ing to the energy-saving schedule
schedule and clock settings.
v
Technical Specifications
;
Warranty
9.
Power: 240 Vac, 50/60 Hz
Load: 16.7 A maximum (resistive only)
Power: 4000 watts (NI) @ 240 Vac
Display range: 0°C to 60°C (32°F to 140°F)
Display resolution: 0.1°C (0.1°F)
Setpoint range: 5°C to 30°C (40°F to 86°F)
Setpoint interval: 1°C (1°F)
Storage: -20°C to 50°C (-4°F to 120°F)
Approvals: CSA/UL
Data backup: In the event of a power failure, most settings are saved. Only
the time must be re-adjusted if the power failure lasts more than 2 hours. The
thermostat will return to the mode that was active prior to the power failure.
10.
Aube warrants this product, excluding battery, to be free from defects in the workmanship or materials,
under normal use and service, for a period of three (3) years from the date of purchase by the
consumer. If at any time during the warranty period the product is determined to be defective or
malfunctions, Aube shall repair or replace it (at Aube's option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased
it, or
(ii) contact Aube. Aube will make the determination whether the product should be returned, or
whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown
by Aube that the defect or malfunction was caused by damage which occurred while the product was in
the possession of a consumer.
Aube's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE
SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM
ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some provinces and states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE
DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
THREE-YEAR DURATION OF THIS WARRANTY. Some provinces and states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from province or
state to another.
11.
Customer Assistance
n
o
Press Pgm to access the programming mode. Period 1 is selected.
p
Press Hour and Min to set the start time of the selected period, or press
Clear if you want to skip the period (--:-- is displayed).
If you have any questions about the product installation or operation, or concerning the
warranty, contact us at:
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec
J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: [email protected]
q
Press Pgm to select another period, or press Day to select another day.
Then repeat step 3.
r
For more information on our products, go to
www.aubetech.com
Press Mode to exit the programming mode.
To modify the schedule:
Press Day to select the day to program (hold for 3 seconds to select the
entire week).
NOTE: If no button is pressed for 60 seconds, the thermostat will automatically exit the programming mode.
TH110
®
As an ENERGY STAR partner, Aube Technologies has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
400-110-000-A
2/6/05
2/2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement