Aube Technologies TH110A-SP-P User manual

Aube Technologies TH110A-SP-P User manual
INSTALLATION
NOTE : The "Problems and Solutions" section at the end of this user's guide will
help you to correct your problems during the installation.
MODEL TH110A-SP-P (120 V)
Electricians or experienced technicians should install the thermostat.
SUMMARY
u
This thermostat has been designed to operate with any installation
which has a RESISTIVE load not exceeding 2400 W (20 A) @ 120 VAC
such as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is not compatible with a low voltage controller used by
a central heating system.
This thermostat is designed to be used with a self-protected heating
system equipped with thermal cut off and circuit breaker.
OPTIONS SELECTION
At the back of the thermostat, there are three selection switches to set at
your preferences.
PARTS INCLUDED
Temperature in °C or °F, time in 12 or 24 hours and Early Start function.
- One (1) TH110A-SP-P (120 VAC) thermostat
- Two (2) 6-32 screws
- Four (4) solderless connectors (for copper wire)
u
TO SET TIME AND DAY
Press on DAY, HOUR and MIN buttons to adjust time and day.
u
TO RECORD THE
(COMFORT) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
or
button. Press on
button (2 to 3 seconds) until icon appears on display.
u
TO RECORD THE
(ECONOMY) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
or
button.
Press on button (2 to 3 seconds) until icon appears on display .
1) Connecting wires and mounting thermostat
TO RECORD THE
Connect the rear thermostat wires to the 120 V LINE and to the load using
solderless connectors for copper wires. See schematic diagram.
u
(VACATION) SETPOINT TEMPERATURE
To program the Vacation temperature, select the desired degree using the
buttons and press on the
and
buttons simultaneously
until the
icon is displayed (app. 3 seconds).
u
TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER
PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of the thermostat
clean and free from obstructions.
Push the excess wire back into the electrical box to prevent interference with the
thermostat. Secure the thermostat using two (2) 6-32 screws. Once the
thermostat is properly installed, return power to heating system.
OPERATING MODES
To select an operating mode, use MODE button.
AUTO:
MAN:
Runs the program.
or
shows temperature setting
and can override temporarily your programming up to the
next program.
Maintains the selected temperature.
the temperature setting.
or
changes
SUPPLY
BEFORE
AFTER
120 V LINE
OLD
THERMOSTAT
BLACK
B
BLACK
120 VAC
B
60 HZ
W
WHITE
W
B
W
BLACK
BLACK
W
B
LOAD
LOAD
NOTE : All cables and connections must conform to the local electrical code.
WARNING: Special CO/ALR solderless connectors must be used when
connecting with aluminum conductors.
Power-up
Set the On/Stand by switch to On.
2400 W (NI) @ 120 Vca
When power is applied for the first time, the
display must show the time 00:00, the room
temperature and the Manual mode icon (
).
Other information might show up on the display if
installation is defective or does not comply with the
instructions.
NOTE : The On/Stand by switch set to Stand by
will place the thermostat in sleep mode.
Ideal for summertime.
920-110-001-00-1-B
1/3
OPERATING MODES
For savings to be obtained, you must lower the temperature for a period of 2 to 3
times the delay required to bring the temperature back to your comfort level.
The TH110A-SP-P has two (2) operating modes.
Example : If your system takes one hour to go from your saving temperature level
to your comfort temperature Ievel, it is useless to lower the temperature for a
period less than 2 to 3 hours.
MANUAL (
)
This mode allows you to maintain a constant temperature in the room.
1- To activate this mode, press on Mode button to display the
2- Set the desired temperature using the
pre-programmed
,
or
settings.
(To select the
setting, press on
and
icon.
a) To Program your Schedule
buttons or select the
1- Press on PGM button to access the programming mode.
simultaneously.)
2- Press on Day button to select the day to be programmed. You can select
all days of the week by pressing on Day button for 3 seconds.
3- Press on PGM button to select program 1, 2, 3 or 4.
AUTOMATIC (
4- Press on Hour and Min buttons to program the time.
)
5- When you have completed your programming, press on Mode button
to exit this function.
This mode executes your own programming.
To activate this mode, press on Mode button to display the
icon.
The
or
icon indicates which temperature setting is used. Also, the icon
of the program number will be shown.
b) To Erase a Program :
Select the program using PGM and Day buttons, and press on Clear
button. The time field displays --:-- when the program is inactive.
Memory back-up
In the event of a power failure, an internal circuit will maintain the programming
and the time. But only the time could have to be set if power failure is more than
2 hours.
c) Example 1 : Comfort period from 7:00 AM to 10:30 PM
Economy period from 10:30 PM to 7:00 AM
Identical schedule for all days of the week.
1- Press on PGM button to access the programming mode.
Early Start function
2- Press on Day button 3 seconds to select every day of the week.
The thermostat is providing a built-in function enabling it to calculate the
optimum time to start the heating system to achieve the desired temperature
setting at the programmed time. This function could start the heating system as
early as 6 hours prior to the programmed time. To enable this function, set the
switch E.S. to “ON” at the back of the thermostat.
3- Press on Hour button to enter 7:00 AM, Prog. 1 (
4- Press on PGM button again to select Prog. 2 (
Hour and Min buttons to enter 10:30 PM.
).
), and press on
5- Press on Mode button to exit this function.
d) Example 2 : Comfort period: Monday to Friday from 6:15 AM to
8:15 AM and from 5:00 PM to 10:00 PM.
Saturday & Sunday from 7:30 AM to 11:00 PM.
PROGRAMMING
Programming the time and day
Schedule/Day
1- Set the time using the Hour and Min buttons.
2- Set the day using the Day button.
MON.
TUES.
WED.
THU.
FRI.
SUN.
SAT.
PROG. 1
6:15 AM 6:15 AM 6:15 AM 6:15 AM 6:15 AM 7:30 AM 7:30 AM
PROG. 2
8:15 AM 8:15 AM 8:15 AM 8:15 AM 8:15 AM
---
---
Programming the Comfort, Economy and Vacation settings
PROG. 3
5 PM
5 PM
5 PM
5 PM
5 PM
---
---
The Comfort
, Economy
and Vacation
settings respectively represent
the temperatures that you wish to have during the day
, at night or while you
are away at work
, or while you are away for an extended period
.
PROG. 4
10 PM
10 PM
10 PM
10 PM
10 PM
11 PM
11 PM
NOTE : It is faster to program the same schedule for every day and then modify
the exception days.
To program your settings
a) To program the Comfort temperature, select the desired degree using the
buttons and press the
button until the
icon is displayed
(app. 3 seconds).
1- Press on PGM button to access the programming mode.
b) To program the Economy temperature, select the desired degree using the
buttons and press the
button until the
icon is displayed
(app. 3 seconds).
3- Press on Hour and Min buttons to enter 6:15 AM, Prog. 1 (
c)
To program the Vacation temperature, select the desired degree using the
buttons and press on the
and
buttons simultaneously
until the
icon is displayed (app. 3 seconds).
d) Press the Mode button to exit this function and return to the normal
operating mode.
2- Press on Day button 3 seconds to select every day of the week.
4- Press on PGM button to select Prog. 2 (
enter 8:15 AM.
).
) and Hour and Min buttons to
5- Repeat step 4 to enter Prog. 3 (5:00 PM) and Prog. 4 (10:00 PM).
NOTE : When making modifications, make sure you are in the right
program.
To modify the Saturday and Sunday schedules:
Schedule programming
6- Press on Day button until SA or SU is displayed.
The TH110A-SP-P allows 4 setting changes for each day of the week. There are
no pre-set programs.The programs are tailored to perfectly adapt to your life
style. The principle is very simple. For each day, enter the time at which you wake
up (P1), the time you leave for work (P2), the time you arrive back home (P3) and
the time you go to bed (P4).
Program
Mode
Time
7- Press on PGM button to select Prog. 1 (
buttons to enter 7:30 AM.
) and Hour and Min
8- Press on PGM button to select Prog. 2 (
erase it.
) and then Clear button to
9- Press on PGM button to select Prog. 3 (
erase it.
) and then Clear button to
) and then Hour and Min
1
Wake-up time
2
Departure time
10- Press on PGM button to select Prog. 4 (
buttons to enter 11:00 PM.
3
Return time
11- Press on Mode button to exit this function.
4
Bed time
920-110-001-00-1-B
2/3
Temporary or permanent temperature bypass
WARRANTY
This operation allows you to temporarily modify the room temperature while you
are in the Automatic mode. Simply press on
or
button to select the desired
temperature, or the
or
button to select the Comfort or Econo settings you
have programmed.This temperature will be maintained until the beginning of the
next programmed schedule.
You can also switch to the Vacation setting for a prolonged absence by pressing
on
and
at the same time.The display will show
icon. In that case,
the derogation is permanent. To return to the normal operating mode, press on
Mode button.
If you wish to immediately return to the programmed settings, press on Mode
button twice.
CHARACTERISTICS
• Model:
TH110A-SP-P (120 VAC)
• Supply:
120 VAC, 50/60 Hz
• Load:
20 A maximum (resistive only)
• Power:
2400 watts (NI) @ 120 VAC
• Approvals:
CSA / UL
• Display range:
0 to 60 °C (32 to 140 °F)
• Setting range:
5 to 30 °C (40 to 85 °F)
• Comfort default setting:
20 °C (68 °F)
• Econo default setting:
18 °C (64 °F)
• Vacation default setting:
10 °C (50 °F)
• Storage:
-20 to 50 °C (-4 to 120 °F)
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY
This product is warranted against material defects and workmanship in normal
use for a period of one year, from the date of the original purchase from
authorized dealers. During this period, AUBE technologies inc. will repair or
replace the product with a new or of equivalent quality at AUBE'S option, without
charge, any product proven defective in normal use.
Warranty does not cover transportation costs. Nor does it cover a product
subjected to misuse or accidental damage. This warranty does not cover the cost
of installation, removal or reinstallation.
This limited warranty is in lieu of all other warranties, obligations or liabilities
expressed or implied by the company. In no event shall AUBE technologies inc.
be liable for consequential or incidental damages resulting from installation of this
product. Some states or provinces do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so the above exclusions or limitations may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
The defective product and the original sale receipt must be returned to the
original dealer or shipped pre-paid, insured and addressed to:
Aube technologies inc., 705 Montrichard, Iberville (Quebec),
Canada, J2X 5K8
www.aubetech.com
[email protected]
If you have any questions concerning the installation or programming of this
product, please call our technical assistance at (450) 358-4600 for the Montreal
area or 1-800-831-AUBE for outside area, Monday to Friday between
8:30 AM and 5:00 PM Eastern time.
PROBLEMS AND SOLUTIONS
PROBLEMS
CAUSES
SOLUTIONS
No display
• Circuit breaker is open
• Power failure
• The thermostat switch is
in Stand by position
• Check 120 VAC presence
at the thermostat
• Put the switch
in On position
The thermostat is loosing
the time but not the programming
• Power failure more than
2 hours
Room temperature shown is wrong
• A draft is nearby the thermostat
• Eliminate the draft
Heating system always on
• Bad installation
• Check installation
The thermostat displays heating
but heating system is not turned on
• Bad installation
• Check installation
• Check 120 VAC presence
at the heating system
Programs do not change as you want
• Incorrect programming hours
• Wrong programming mode selected
• Check actual time
in AM & PM as well
as program times
(AM is not displayed)
• Make sure operating mode
is set to AUTO
01/04/02
920-110-001-00-1-B
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement