400-032-001-B ENG (print at 90%).fm Page 1 Thursday, November 30, 2006 8:52 AM
TI032-3W
Installation and User Guide
Programmable Wall Switch
n
1.
Applications
NEW 3-WAY INSTALLATION
The TI032-3W switch can be used in a single-pole or 3-way installation
with the following types of lighting:
• Incandescent
• Halogen
• Low-voltage halogen with transformer
• Fluorescent
120 VAC
See NOTE A
The TI032-3W switch cannot be used with a load below 40 W or above
500 W.
o
2.
Installation
The jumper wire is not required in this installation. A single-pole
switch can be used as the other switch in a 3-way installation.
n
o
Cut power at the circuit breaker to avoid electric shock.
Remove the existing switch. (For a 3-way installation, identify and
label the wire that is connected to the “common” screw.)
p
q
p
Install the new switch (refer to the appropriate section below).
n
Apply power at the circuit breaker.
NOTE A:
The white wire is not the neutral wire but the wire going to the
load.
SINGLE-POLE INSTALLATION
Line
120 VAC
Neutral
See NOTE A
3.
Power-On
Pry the switch door open from the
bottom using a small screwdriver.
Reset
o Ensure the ON/OFF selector is set
to ON.
Control (4)
p Reset the switch using a paper clip.
On/Off
0:00 and MO will flash.
selector
If the display is blank:
•
Ensure the ON/OFF selector is properly engaged in the ON position. Push it to the right using a small screwdriver.
•
If the programmable switch controls a lamp equipped with a
built-in On/Off switch, ensure the lamp switch is set to On.
•
Ensure the light bulb is not burned out and is tightly screwed in its
socket.
EXISTING 3-WAY INSTALLATION
If either switch does not work properly, rewire the jumper between the
"common" screw and the other screw.
120 VAC
WARNING: Before replacing the light bulb, place the ON/OFF
selector in the OFF position. Failure to do so might damage the
switch.
Line
Neutral
Connect wires "2" and "C" of the TI032-3W to the line (120 V) wire.
EXISTING 3-WAY INSTALLATION
q
NOTE: The switch displays the time in 24-hour format by default or
following a reset.
n
120 VAC
Red
b) Press the MIN and HOUR buttons simultaneously and brieftly (0:00 display = 24-hour, 12:00 display = 12-hour ).
o
Red
3-wire cable
Connect wire "C" of the TI032-3W to the "common" wire, identified when
removing the old switch. Connect the other two TI032-3W wires to the
two remaining wires.
At the other 3-way switch, connect the jumper wire between the "common" screw and the screw where wire "1" of the TI032-3W is connected.
TI032-3W
To change to 12-hour format (or vice versa), proceed as follows:
a) Press one of the control buttons to ensure the MAN or
AUTO indicator is displayed.
See NOTE A
Jumper
4.
Setting the Clock
p
q
Set the time using the HOUR and MIN buttons. If you have
selected the 12-hour format, ensure that PM appears on the
screen when an afternoon time is displayed.
Set the day by using the DAY button.
Press one of the control buttons or close the switch door to
return to normal operation.
400-032-001-B
30/11/06
1/2
400-032-001-B ENG (print at 90%).fm Page 2 Thursday, November 30, 2006 8:52 AM
r
Selecting the Operating Mode
5.
The programmable switch has 2 operating modes: manual (MAN) and
automatic (AUTO). To switch mode, press the switch door for 3 seconds.
Manual Mode
The programmable switch operates as a regular switch.
Briefly press the switch door to turn the lights On or Off.
The mode (MAN) and state (ON or OFF) are displayed.
Automatic Mode
The programmable switch follows the programmed
schedule. The mode (AUTO), state (ON or OFF) and
current program number are displayed.
To temporarily override the programmed schedule,
press the switch door. The new state (ON or OFF) will
flash to show that this state is temporary. The override remains in effect
until you press the switch door again or until the beginning of the next
program.
s
Programming
Blank display
• Verify circuit breaker at main panel.
• Verify if light bulb is burned out
• Ensure the ON/OFF selector is at ON.
• Reset the switch using a paper clip.
Faded or irregular
display
• Load is less than 40 W
• Ambient temperature is below freezing
point
Cannot switch between
24-hour format and
12-hour format
First, press one of the control buttons so
that MAN or AUTO appears on display.
Programs do not run as
expected
• Make sure the switch is properly programmed.
• Note that - : - - indicates an inactive program, 00:00 indicates midnight.
• If the switch has been configured for
12-hour format, check that PM appears on
the left side of the screen when an afternoon time is displayed.
The metal plate is hot
This is normal with high loads (maximum of
500 W).
Pry the switch door open using a small screwdriver.
Press the PGM button to display a program and its
On or Off time. For example, when you first press
PGM, program number 1 (P1) and its On time
(ON) will appear. - : - - will appear instead of the
time if the program is not set (inactive).
;
p
Press the DAY button to select the day to which
you want to apply the program.
NOTE: If you want to apply the program to every
day of the week, press DAY until all the days are
displayed. (This still counts as 1 program, not 7)
q
Press the HOUR and MIN buttons to set the ON time (time when
you want the lights to turn on). If you have selected the 12-hour
format, ensure that PM appears on the screen when an afternoon
time is displayed.
r
After you have programmed the ON time, press the PGM button to
display the OFF time (time when you want the lights to turn off).
s
Repeat steps 3 through 5 to program the OFF
time. If the program ON time is set for every day of
the week, the program OFF time will automatically
be set for every day.
t
To set another program, repeat steps 2 through 6.
Programs that are not set will remain inactive.
u
Press one of the control buttons or close the switch door to return to
normal operation.
Clearing a Program
Press the PGM button until the desired program is selected. Hold the
PGM button for 3 seconds. - : - - appears when the program is erased.
t
Technical Specifications
Supply: 120 VAC, 50 / 60 Hz
Minimum load: 40 watts
Maximum load: 500 watts
Operating temperature range: 5°F to 122°F (-15°C to 50°C)
Storage temperature range: -4°F to 122°F (-20°C to 50°C)
Power outage: The programs are protected by a rechargeable battery.
The screen is blank during the power outage.
Certifications: CSA & UL
7.
8.
Troubleshooting
6.
You can set up to 7 programs. To set a program, you need to enter its
start time (ON) and its end time (OFF).
n
o
u
9.
Warranty
AUBE warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years
from the date of purchase by the consumer. If at any time during the warranty
period the product is determined to be defective or malfunctions, AUBE shall repair
or replace it (at AUBE's option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it, or
(ii)
contact AUBE. AUBE will make the determination whether the product
should be returned, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall
not apply if it is shown by AUBE that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
AUBE's sole responsibility shall be to repair or replace the product within the terms
stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF
ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the exclusion or limitation of
incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS
WARRANTY. Some provinces, states or regions do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which
vary from one province, state or region to another.
10.
Customer Assistance
If you have any questions on the product installation or operation, contact us at:
705 Montrichard Avenue
Saint-Jean-sur-Richelieu, Quebec
J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: [email protected]
For more information on our products, go to
www.aubetech.com
TI032-3W
400-032-001-B
TROUBLESHOOTING
30/11/06
2/2
">
