Hazardous Area Equipment

Hazardous Area Equipment
Hazardous Area Equipment
Customised and IECEx Certified Hazardous Area Solutions
ENCLOSURES AND CLIMATE CONTROLHAZARDOUS AREA EQUIPMENT
NHP Electrical Engineering Products
AUS
NZ
1300 NHP NHP
0800 NHP NHP
nhp.com.au
nhp-nz.com
NHP Hazardous
Area Solutions
IECEx certified Hazardous Area
workshop in Australia
Full range of IECEx certified
products
Industry leading turnaround
time on custom assemblies
Certified Hazardous Area experts
National and IECEx certified
training courses
2
Index
INTRODUCTION
5
SECTION 4: INTRINSIC SAFETY EQUIPMENT
SECTION 1: LIGHTING
Selection chart
14
GM International Intrinsically Safe Isolators
SECTION 5: SWITCHING AND FIELD DEVICES
Hazardous Area Linear Lights
EXEL-L LED Linear Lights
16
Selection chart
EXEL Fluorescent Linear Lights
16
Hazardous Area Plugs and Sockets
EXEN Fluorescent Linear Lights
18
Plugs and Sockets
FLFE Fluorescent and LED Linear Lights
19
Hazardous Area Isolators
Linear Light Fitting Mounting Brackets
22
Rotary Switches
60
63
64
Hazardous Area Field Switches and Sensors
Hazardous Area Flood Lights
EVL LED Floodlights
23
Steute Limit Switches and Sensors
EWL LED Floodlights
24
Hazardous Area Pull-Wire Switches
SLEE Floodlights
26
Austrol Switches
TIGER Floodlights
27
SECTION 6: EX SIGNALLING
Selection chart
Hazardous Area Pendant Lights
EVE Pendant Lights
28
Hazardous Area Sight
EWAE Pendant Lights
29
Moflash Sight
65
72
76
77
Hazardous Area Sound
SECTION 2: CONTROL STATIONS AND JUNCTION BOXES
Selection chart
54
32
Moflash Sound
80
SECTION 7: CABLE GLANDS AND ACCESSORIES
Hazardous Area Control Stations
Cortem EFDC (Ex d) Control stations
34
Selection chart
Standard Control Station
34
Hazardous Area Cable Glands
Ex Cable glands
Hazardous Area Junction Boxes
S Series (Ex d) Junction Boxes
38
Hazardous Area Adaptors, Reducers and Accessories
SA (Ex e) Junction Boxes
39
Plugs, Adaptors, Reducers and Accessories
84
85
88
SECTION 3: CUSTOM ENCLOSURES
Selection chart
42
Hazardous Area Custom Enclosures
Cortem (Ex d) Custom Assemblies
44
Cortem EJB Motor Starters
46
Cortem SA (Ex e) Custom Assemblies
49
3
3 Step Product Selection Guide
To select the optimal products for your application please
reference the documentation below
1 - Technical Data Sheets
2 - IECex Certification
3 - Product Installation Manual
For Documentation please go to nhp.com.au
4
SELECTION OF HAZARDOUS AREA ELECTRICAL EQUIPMENT
In order to select electrical apparatus for use in hazardous
areas it is necessary to have the following information:
Typical hazardous area industries:
Dust
Gases and Vapours
1. Area Classification
2. Gas, vapour or combustible dust group
• Oil refineries and chemical plants • F ood manufacturing
• Offshore drilling rigs
•G
rain handling and storage
• Spray booths
• Chemicals/fertilizer
4. The required IP rating of the apparatus
• Sewerage treatment plants
• Plastics
1. Area Classification
• Oxygen and Acetylene
• Wood/pulp/paper
• Aircraft hangers
•M
ilk powder
• LNG plants
• F lour Mills
• Wharves for petroleum
and LNG vessels
• Pharmaceuticals
• Paint manufacturers
•R
ecycling operations
3. The “T” rating or the ignition temperature of the hazard
The areas are classified into ZONES, and these zones
are based on the frequency of the appearance of an
explosive atmosphere and the duration for which it
can last.
Summarised in the table below:
•M
etal processing
• Distilling
• F iberglass manufacturing
• Laboratory and fume cupboards • E xplosive factories
Dust
Gases and Vapours
Zone 0
Area in which an explosive gas-air mixture
is continuously present or present for long
periods.
Zone 20
Area in which an explosive dust-air mixture
is continuously present or present for long
periods.
Zone 1
Area in which an explosive gas-air mixture
is likely to occur for short periods in normal
operation.
Zone 21
Combustible or conductive dusts are
present and are likely to occur for short
periods in normal operation.
Zone 2
Area in which an explosive gas-air mixture
is not likely to occur, and if it occurs it will
only exist for a very short time due to an
abnormal condition.
Zone 22
Area in which an explosive dust mixture
is not likely to occur, and if it occurs it will
only exist for a very short time due to an
abnormal condition.
2. Gas, vapour or combustible dust group
Gases and vapours are divided into three groups:
Group I
Group II
Mining
M1
M2
Group III
Explosive Gas Atmosphere
Explosive Dust Atmosphere
Sub-Division
Ignition Energy
Sub-Division
Explosive
Atmosphere
IIA (eg: Propane)
260 Micro-joules
IIIA
Combustible
flyings
IIB (eg: Ethylene)
95 Micro-joules
IIIB
Non-conductive
dust
IIC (eg: Acetylene 18 Micro-joules
and Hydrogen)
IIIC
Conductive dust
The hazard level of the gases and dusts increases from gas groups IIA to IIC and dust groups IIIA to IIIC. The most severe in both cases
being IIC and IIIC.
5
3. Temperature or “T” rating for explosive gas
atmospheres.
The source of ignition in a Hazardous Area can be an arc or a
spark or even a hot surface.
T Rating
Maximum Temperature
T1
450 ºC
T2
300 ºC
T3
200 ºC
T4
135 ºC
T5
100 ºC
T6
85 ºC
Since electrical equipment generates heat in normal operation
we need to ensure that a hot surface on electrical apparatus
cannot ignite a surrounding explosive gas atmosphere or a
dust cloud or layer.
All hazardous materials have what is known as an “Ignition
Temperature”, this is the minimum temperature at which the
hazardous material when mixed with air will ignite and sustain
combustion, without an ignition source (auto-ignition or
spontaneous ignition).
For explosive gas atmospheres a“T” rating is given. For example,
a T6 rated product will not exceed 85 ºC and a T3 will not
exceed 200 ºC. While in service in Hazardous Area Equipment
for explosive dust atmospheres are given a maximum surface
temperature rather than a “T” rating. This is so dust build up, or
layers can be accounted for via de-rating calculations.
SELECTION OF TEMPERATURE RATING FOR HAZARDOUS DUSTS
Dusts pose additional problems when dealing with
temperature. Dust can settle on equipment and ledges to
form layers. Because of this we have to consider dusts in two
forms:
1) As a cloud mixed with air
2) As layers settled on surfaces
Dust as a cloud and dust in layers will have different ignition
temperatures and we need to consider the lowest of these
two.
Dust in the form of a layer on electrical equipment can impair
heat dissipation and cause increased temperatures to the
equipment.
Temperature increase as a result of layers can also cause the
dust to dry out and give rise to spontaneous combustion of
the dust in the layers.
Disturbance of the dust layers can cause it to rise and mix
with air to form an explosive cloud.
a) For Dust Clouds
You must select equipment with a T rating that is two thirds
that of the ignition temperature of the dust hazard.
E.g. if the ignition temperature of the hazardous dust is 150ºC
then the equipment T rating must not exceed 100ºC or T5
b) For Dust Layers
You must select equipment with a T rating that is 75ºC less
than the ignition temperature of a layer on the surface of the
equipment.
E.g. if the ignition temperature of the dust layer is 275ºC then
the equipment T rating must not exceed 200ºC or T3.
The thickness of dust layers is critical to the whole operation
and this is the main reason for good housekeeping. If the
layers are going to be more than 5 mm then testing must be
carried out on the individual hazardous dust at the specified
thickness to obtain the layer ignition temperature at that layer
thickness.
Pressure wave from a relatively small dust explosions have
historically converted dust layers on sites into clouds, giving
rise to much more serious secondary explosions.
EQUIPMENT PROTECTION LEVELS (EPLs)
EPL’s were introduced to Hazardous Area classifications at the
same time optional risk assessments were introduced. Rather
than define the probability an explosive atmosphere will
exist (Hazardous Zones) EPL’s consider the consequence of
an explosion, and a protection level is assigned based on its
ignition risk.
6
A risk based approach to Hazardous Area classification is used
to ensure that equipment manufactured for or installed in a
Hazardous area will not become a source of ignition, even in
a failed state.
During classification, a risked based approach of
consequences of an explosion, can be used to determine
if equipment used can be of a higher or lower level of
protection, beyond the nominally used zone equipment
selection criteria.
Equipment Protection Levels (EPLs)
EPL Ga/Da: Equipment having a very high level of protection,
which will not act as a source of ignition in normal operation,
expected faults or when subject to rare faults.
EPL Gb/Db: Equipment having a high level of protection,
which will not act as a source of ignition in normal operation
or during expected faults.
EPL Gc/Dc: Equipment having an enhanced level of
protection which will not act as a source of ignition in normal
operation and reduce the likelihood of acting as an ignition
source during expected faults, e.g an indicator lamp failure.
Protection level
Zone
EPL
Zone 0
Ga
Zone 20
Da
Zone 1
Gb
Zone 21
Db
Zone 2
Gc
Zone 22
Dc
Very High
High
Enhanced
TYPES OF PROTECTION FOR ELECTRICAL APPARATUS IN HAZARDOUS AREAS - EXAMPLES
Type of protection
Flame proof
enclosure
Ex d
Increased safety
Ex e
Intrinsic safety
Ex i
Non-sparking
Ex n
Protection by
enclosure
Ex t
Diagram
Description
Standard
Ex d - “Flameproof Enclosure – type of protection
for electrical equipment in which the enclosure will
withstand an internal explosion of a flammable mixture
which has penetrated into the interior without suffering
damage and without causing ignition”.
AS/NZS 60079-1
Ex e - “Increased safety – type of protection applied to
electrical equipment that does not produce arcs and
sparks in normal service in which additional measures
are applied so as to give increased security against the
possibility of excessive temperatures and the occurrence
of arcs and sparks”.
AS/NZS 60079-7
Ex i - “Intrinsically safe circuit – a circuit in which any spark
or any thermal effect produced in the test conditions
prescribed in the standard (which include normal and
specified fault conditions) is INCAPABLE of causing
ignition of a given explosive atmosphere”.
AS/NZS 60079-11
Ex n - II– type of protection applied to electrical
equipment such that, in normal operation, it is not
capable of igniting a surrounding explosive gas
atmosphere and a fault capable of causing ignition
is not likely to occur.”
AS/NZS 60079-15
Ex t - “An enclosure which excludes dust, and which will
not permit arcs, sparks or heat otherwise generated or
liberated inside the enclosure to cause ignition of exterior
accumulations or atmospheric suspensions of a specified
dust on or in the vicinity of the enclosure”.
AS/NZS 60079-31
7
EX HAZARDOUS AREA STANDARDS AND LEGISLATION FLOW CHART
AS/NZS 3000 – Wiring rules
- Section 7.7: requirements for electrical
installations in hazardous areas
Explosive atmospheres
- Amendment 2: references to standards
governing hazardous areas
AS/NZS 60079.0
Repairing the equipment
Plants’ inspection and maintenance
AS/NZS 3800
AS/NZS 60079.17
General requirements
Explosive atmospheres
Classification of areas
Gases: AS/NZS 60079.10.1
Dusts: AS/NZS 60079.10.2
Electrical installations design, selection
and erection
AS/NZS 60079.14
ELECTRICAL LEGISLATION-GENERAL
Within Australian states and territories there is an Act or
Regulation of parliament that requires electrical installations
to comply with AS/NZS 3000 - Wiring rules. The exact
requirements vary State to State, however generally it is the
responsibility of the electrical worker or contractor to ensure
that the installation complies with regulations (including
those referenced in AS/NZS 3000). There are serious penalties
for non-compliance, including loss of license, fines and jail
terms. Although there are often exclusion to the legislated
applicability of the wiring rules for places like mines, quarries
and petroleum leases, we generally find in such cases that the
rules are called up in site safety management plans or contract
documents, so compliance is still required, just via a slightly
different mechanism.
Section 7.7 of AS/NZS 3000:2007 sets out the requirements for
electrical installation in Hazardous Areas. AS/NZS 3000:2007
Amendment 2 requires compliance with these “harmonised”
standards, the AS/NZS 60079 series.
The relevant clauses of Amendment 2 are reproduced below
with some added commentary:
RESPONSIBILITY FOR CLASSIFICATION OF A HAZARDOUS AREA
AS/NZS 3000:2007 - 7.7.2.1
The responsibility for classification of a Hazardous Area rests
with the persons or parties in control of the installation. The
requirements are contained in AS/NZS 60079.10.1 for gas or
vapor and AS/NZS 60079.10.2 for combustible dust.
Commentary: The critical take-away from this is, the
acknowledgment of responsibility that rests with the owner
or occupier of the premises that houses the Hazardous Area
8
in question – a responsibility that is consistent with standard
OHS legislation. While this person is not expected to perform
the classification themselves, he/she is obligated to identify
the potential for a Hazardous Area and engage a competent
person (see page 7 for further explanation of competency
requirements) to do so.
ELECTRICAL EQUIPMENT
COMPETENCY OF PERSONNEL
Selection
AS/NZS 3000: 7.7.2.4.2
AS/NZS 3000:2007 - 7.7.2.4.1
Refers to competency requirements in AS/NZS 60079.14. The
relevant clause in that standard is 4.4, reproduced below:
Electrical equipment selected for use in Hazardous Areas shall
comply with the appropriate requirements as specified in
AS/NZS 60079.14.
Installation
AS/NZS 3000:2007 - 7.7.2.4.2
Electrical equipment shall be installed in accordance with the
installation requirements of AS/NZS 60079.14.
Commentary: What is essential to understand here, is that to
comply with AS/NZS 3000:2007, electrical equipment that is
selected and installed in a hazardous area environment must
be compliant to AS/NZS 60079.14.
AS/NZS 60079.14 – 4.4
The design of the installation, the selection of equipment and
the erection covered by this standard shall be carried out only
by persons whose training has included instruction on the
various types of protection and installation practices, relevant
rules and regulations and on the general principles of area
classification. The competency of the person shall be relevant
to the type of work to be undertaken. Appropriate continuing
education or training shall be undertaken by the personnel on
a regular basis.
Competency may be demonstrated in accordance with AS/NZS
4761, Competencies for working with electrical equipment for
hazardous areas (EEHA), or equivalent training and assessment
framework.
Commentary: Without exception, persons who intend to
work with EEHA are to be appropriately competent to a
level that is relevant to the particular works that are being
undertaken – regardless of its position in the project cycle. In
essence, whether a person is involved in the design, installation
or maintenance stage, they must be able to demonstrate
competency to ensure utmost safety measures are ensured.
It is also important to note that as standards and regulations
change and the various technologies involved advance, it is
expected that persons continue to educate themselves to
maintain their competency levels.
9
NHP MAKE HAZARDOUS AREAS EASIER…
At NHP our aim is to provide a world class range of Hazardous
Area solutions for the hazardous market and to ensure this is the
case, we provide a range of value-add tools for our customers.
From product selection through to expert advice, NHP make
engineering a solution that meets your requirements easier
than ever before.
For your next HAE project, experience the NHP difference.
Hazardous Area Training
To ensure you and your colleagues are competent in working
within Hazardous Areas, NHP also offer a range of training
packages from ‘lunch and learn’ sessions to single day tailored
awareness courses, and 5 day training courses with nationally
recognised competencies. With the flexibility to offer courses
both on site and at one of our 50+ branch locations throughout
Australia, you can trust NHP to work with you to find a training
option that works for you.
IECEx Certified Hazardous Area Workshop
NHP supplies not only a range of Hazardous Area Equipment,
but also, customer specific systems via our certified
manufacturing and assembly workshop located at Laverton.
In this workshop, accredited staff design, construct and
inspect the Cortem range according to the requirements of
IECEx certification. This allows for flexibility to produce custom
solutions to suit your HAE requirements.
NHP Training University (NTU)
If you want to increase your skill set but avoid lengthy lectures
and the cost of further education, NTU (NHP Training University)
is for you! With valuable training modules introduced regularly,
NTU is FREE and designed to further your key industry
knowledge.
10
The latest module looks at Hazardous Area Equipment and
explains the basic principle of explosion protection from zone
classification and explosion groups, to temperature classes and
the different types of protection available.
HAE Technology Specialist Team
Our Hazardous Area specialists have the experience and
knowledge to apply HAE best practices across a broad range of
industries including Food Manufacturing, Grain, Oil and Gas. The
NHP Ex team have the ‘know how’ to develop and recommend
solutions that provide value to our customers utilising NHP’s
ability to offer complete IECEx solutions delivered in industry
best time frames.
If you’d like to speak to NHP’s HAE Technology Specialist Team,
simply call 1300 NHP NHP (Australia) or 0800 NHP NHP (New
Zealand).
LOCALLY STOCKED
3
N
TY
EAR
W Y
ARRA
Locally stocked Hazardous Area LED lighting
NHP is pleased to release the EXEL-L
series of increased safety, linear
lighting fixtures, complementing the
growing range of Hazardous Area LED
lighting fixtures from NHP.
•
•
•
•
•
•
IECEx certified - zones 1, 2 and 21, 22
Reduce installation and maintenance costs
Energy efficient
Lighting designs available from certified Hazardous Area experts
No UV emissions - no insect attraction
Intrinsically safe optical radiation – (Ex op is)
3
N
TY
EAR
W Y
ARRA
NHP ELECTRICAL ENGINEERING PRODUCTS
1300 NHP NHP | nhp.com.au |
1
Lighting
Selection chart 14
Hazardous Area Linear Lights
EXEL-L LED Linear Lights
EXEL Fluorescent Linear Lights16
EXEN Fluorescent Linear Lights
18
FLFE Fluorescent Linear Lights
20
Hazardous Area Flood Lights
EVL LED Floodlights
23
EWL LED Floodlights
24
SLEE Floodlights
TIGER Floodlights
26
27
Hazardous Area Pendant Lights
EVE Pendant Lights
EWAE Pendant Lights
28
29
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
12
FLOOD LIGHTING
PENDANT LIGHTING
EXIT LIGHTING
FLUORESCENT LIGHTING
13
1
Lighting
Selection Chart
Description
Cortem EXEL-L
Protection
Technique
Zone 1
Zone 2 Zone 21 Zone 22
Group
3
3
3
3
IIC
IIIC
3
3
3
3
IIC
IIIC
Ex nA
Ex tb
-
3
3
3
IIC
IIIC
Ex de
Ex tb
3
3
3
3
IIC
IIIC
LED linear light
Ex d w mb op is
Long life, energy efficient LED tubes
tb
• 3 Year Warranty
• Reduce installation and maintenance costs • 2500-5000 Lumens
• Normal, Emergency and Exit signage
options
• Automatic isolating switch
• Through Wiring
• Reinforced fiberglass and polyester resin
body with polycarbonate diffuser
• IP66
Cortem EXEL
Fluorescent linear light
Ex d
• 18 and 36 W Fluorescent tubes
Ex e
• Normal, Emergency and Exit signage
Ex td
options
• Optional mounting methods
• Through wiring
• Automatic isolating switch
• End of life switching off
• Reinforced fiberglass and polyester resin body with polycarbonate diffuser
•IP66
Cortem EXEN
Fluorescent linear light
• 18 and 36 W Fluorescent tubes
• Normal, Emergency and Exit signage options
• Optional mounting methods
• Through wiring
• End of life switching off
• Reinforced fiberglass and polyester resin body with polycarbonate diffuser
•IP66
Cortem FLFE
LED and Flourescent linear light
• 18, 36 and 58 W Fluorescent tubes
• LED version 1850 - 5400 Lumens
• Normal, Emergency and Exit signage
options
• Optional mounting methods
• Aluminium alloy with toughened
borosilicate glass
• Ex e termination chamber
•IP66
14
1
Lighting
Selection Chart
Description
Cortem EVL
LED Highbay/Floodlight
Long life, energy efficient LED technology
• 5 Year Warranty
• Reduce installation and maintenance
costs
• 3000 - 19,000 Lumens
• Lens options (10°, 20°, 40° and 120°)
• Aluminium alloy with toughened
borosilicate glass
• Ex e termination chamber
•IP66
Protection
Technique
Zone 1
Zone 2
Zone 21
Zone 22
Group
3
3
3
3
IIC
IIIC
3
3
3
3
IIC
IIIC
Ex de
Ex tb
3
3
3
3
IIC
IIIC
Ex de
Ex tb
3
3
3
3
IIC
IIIC
Ex de
Ex tb
3
3
3
3
IIC
IIIC
Ex de
Ex tb
3
3
3
3
IIC
IIIC
Ex de
Ex tb
Cortem EWL
LED Highbay/Floodlight
Long life, energy efficient LED technology
• 5 Year Warranty
• Reduce installation and maintenance
costs • 3700 - 17,000 Lumens
• Lens options (10°, 20°, 40° and 120°)
• Aluminium alloy with toughened borosilicate glass
• Ex e termination chamber
•IP66
Cortem SLEE
Floodlight
• 150, 250 and 400W
• Copper-free aluminium body
• Tempered glass cover
• IP 65/66
• Different lamp options
Cortem TIGER
Floodlight
• 150, 250 and 400W
• Copper-free aluminium body
• Tempered glass cover
• IP 65/66
• Different lamp options
Cortem EVE
LED Pendant Light
• Low glare - remote phosphore
technology lens
• Aluminium alloy with toughened
borosilicate glass
• Ex e termination chamber
• Multiple mounting options
•IP66
Cortem EWAE
Metal halide, sodium vapour, mercury
Vapor options• 150W to 400W
• Aluminium alloy with toughened
borosilicate glass
• Ex e termination chamber
• Multiple mounting options
•IP66
15
1
Hazardous Area Linear Lights
EXEL-L LED Linear Lights
Zones 1, 2 and 21, 22
IECEx CML 15.0044
Ex d e mb op is IIC T5 Gb
Ex tb IIIC T64°C Db
Ex d e mb op is IIC T6 Gb
Ex tb IIIC T49°C Db
IP66
Features and Benefits
•Long life, energy efficient LED tubes
•3 Year warranty
•Reduced maintenance
•4 x M20 Cable entries (3 x IECEx certified plugs supplied)
•Through wiring
•Gland earth continuity plates on both ends
•Vibration resistant
•Suitable for chemically aggressive and extreme environments
Product Selection
Refer to page 22 for bracket selection.
LED lamps included with fixture.
EXEL-L Standard Lights
EXEL215LAU
Lumens
(lm)
2850
5637
#Lamps
2
2
(W max)
29
56
H x W x D (mm)
Weight (kg)
785 x 185 x 155
1370 x 185 x 155
4.9
9.2
Item Type
Catalogue No.
I
I
EXEL215LAU
EXEL230LAU
EXEL-L Standard and/or Emergency Lights
EXEL-L emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping during
installation.
Fitted with an internal battery and electronic inverter for use in emergency operation. The operating time under emergency
operation, depending on requirements, can last from a minimum of 90 minutes to a maximum of 180 minutes.
Lumens
(lm)
2850
5637
#Lamps
2
2
(W max)
29
56
HxWxD
(mm)
785 x 185 x 155
1370 x 185 x 155
Item Type
Catalogue No.
EXEL215LEF4AU
EXEL230LEF4AU
EXEL-L Emergency Exit Lights
EXEL-L e1mergency exit lights are an effective guidance tool, convey important messages, provide a clear, easy-to-follow directional
system. EXEL-L emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping
during installation. Fitted with an internal battery and electronic inverter for use in emergency operation, the operating time under
emergency operation depending on requirements can last from a minimum of 90 minutes to a maximum of 180 minutes.
EXEL215LEXIT24M
Lumens
(lm)
2850
2850
2850
#Lamps
2
2
2
HxWxD
(mm)
785 x 185 x 155
785 x 185 x 155
785 x 185 x 155
Exit
(direction)
Straight Through
Left
Right
Item Type
Catalogue No.
EXEL215LEXIT24M
EXEL215LEXITL24M
EXEL215LEXITR24M
EXEL-L Accessories
EXEL-L spare parts and accessories which include kits for mounting, electronic ballasts, inverters and battery packs etc are available
on request.
Description
LED resin bounded tube for EXEL215LAU
Ballast for EXEL215LAU
Ballast for EXEL230LAU
LED resin bounded tube for EXEL230LAU
16
Item Type
Catalogue No.
LTT3250E
EB215L
EB230L
LTT16350E
NHP HAZARDOUS
AREA LIGHTING
DESIGN
NHP provides an extensive range of Hazardous
Area LED lighting products and in-house lighting
designs to improve efficiency by lowering
energy consumption, minimising maintenance
requirements and reducing installation costs,
combined with our return on investment calculator.
To complement the product range, NHP can also
assist with in-house lighting design through our
team of expert personnel. With market leading
experience and knowledge, this team can assess
new or existing plants and design a tailored solution
that improves lighting quality, decreases the
number of fixtures required and can further reduce
installation time utlising Ex-e junction boxes built
into the fixture.
17
1
Hazardous Area Linear Lights
EXEL Fluorescent Linear Lights
Zones 1, 2 and 21, 22
IECEx CES 07.0001
Ex ed IIC T5
Ex tb T95ºC
IP66
Ambient temp. / Temp. class / Max surface temp.
–40ºC + 55ºC / T5 / 95ºC
Features and Benefits
•Body in black antistatic GRP (Glass Reinforced Polyester)
•4 x M20 cable entries (3 x IECEx certified plugs supplied)
•Through wiring
•Earth continuity plates on both ends
•Vibration resistant
•EOL ballast (End Of Life)
•Internal white powder coated aluminum frame
•Electronic ballast and safety switch
•Suitable for chemically aggressive and extreme environments
Product Selection
Refer to page 22 for bracket selection.
Fluorescent lamps not included
EXEL Standard Lights
#Lamps
2
2
Lamp
(W max)
18
36
HxWxD
(mm)
785 x 185 x 155
1370 x 185 x 155
Weight
(kg)
5.3
7.9
Item Type
Catalogue No.
EXEL218AU1
EXEL236AU1
EXEL218AU1
EXEL Standard and/or Emergency Lights
EXEL emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping during
installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation. The operating time under emergency operation,
depending on requirements, can last from a minimum of 90 minutes to a maximum of 180 minutes.
#Lamps
EXEL218EF4AU
18
Lamp
(W max)
BattDschrg
(hours)
HxWxD
(mm)
Weight
(kg)
Item Type
Catalogue No.
2
18
2
785 x 185 x 155
7
EXEL218EF4AU
2
36
1.5
1370 x 185 x 155
9.6
EXEL236EF4AU
1
EXEL Emergency Exit Lights
EXEL Emergency exit lights are an effective guidance tool, convey important messages, provide a clear, easy-to-follow directional system.
EXEL emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping during installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation The operating time under emergency operation, depending
on requirements, can last from a minimum of 90 minutes to a maximum of 180 minutes.
#Lamps
Lamp
(W max)
BattDschrg
(hours)
HxWxD
(mm)
Weight
(kg)
2
18
2
785 x 185 x 155
5.5
2
2
18
18
2
2
785 x 185 x 155
785 x 185 x 155
5.5
5.5
Exit
(direction)
Straight
Through
Left
Right
Item Type
Catalogue No.
EXEL218EXIT24M
A
A
EXEL218EXITL24M
EXEL218EXITR24M
EXEL218EXIT24M
EXEL Accessories
EXEL spare parts and accessories which include kits for mounting, electronic ballasts, inverters and battery packs etc are available on
request.
Description
Item Type
240V Ballast To Suit EXEL236.... Models (2X36W)
Inverter EXEL
I
Catalogue No.
EB236/240
EI-58
EB236/240
Dimensions (mm)
Light fitting
Dimensions
18 W
36 W
A
A1
B
C
785
420
185
155
1370
720
185
155
19
1
Hazardous Area Linear Lights
EXEN Fluorescent Linear Lights
Zones 2 and 21, 22
IECEx CES 12.0010
Ex nA IIC T5/T4 Gc
Ex tb IIIC T65ºC to T85ºC Db
IP66
Ambient temp. / Temp. class / Max surface temp.
–40ºC +40ºC / T5/ 65ºC
–40ºC +50ºC / T5/ 80ºC
–40ºC +55ºC / T4/ 85ºC
Features and Benefits
•Body in black antistatic GRP (Glass Reinforced Polyester)
•4 x M20 cable entries (3 x IECEx certified plugs supplied)
•Through wiring
•Earth continuity plates on both ends
•Vibration resistant
•Protected opening system through sliding operated by a hexagonal-head tool
•EOL ballast (End Of Life)
•Internal white powder coated aluminum frame
•Electronic ballast and safety switch
•Suitable for chemically aggressive and extreme environments
Product Selection
Refer to page 22 for bracket selection.
Fluorescent lamps not included
EXEN Standard Lights
Lamp
(W max)
18
36
#Lamps
2
2
EXEN218AU
HxWxD
(mm)
785 x 185 x 155
1370 x 185 x 155
Weight
(kg)
4
7.3
Item Type
Catalogue No.
EXEN218AU
EXEN236AU
EXEN Normal and Emergency Lights
EXEN emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping during
installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation, the operating time under emergency operation
depending on requirements and can last from a minimum of 90 minutes to a maximum of 180 minutes.
Lamp
(W max)
18
36
#Lamps
EXEN218EF4AU
2
2
BattDschrg
(hours)
2
1.67
HxWxD
(mm)
785 x 185 x 155
1370 x 185 x 155
Weight
(kg)
8.3
7.8
Item Type
Catalogue No.
EXEN218EF4AU
EXEN236EF4AU
EXEN Emergency Exit Lights
EXEN emergency exit lights are an effective guidance tool, convey important messages, provide a clear, easy-to-follow directional
system.
EXEN emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping during
installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation, the operating time under emergency operation
depending on requirements and can last from a minimum of 90 minutes to a maximum of 180 minutes.
EXEN218EXIT24M
20
#Lamps
Lamp
(W max)
BattDschrg
(hours)
HxWxD
(mm)
Weight
(kg)
2
18
2
785 x 155 x 185
8.3
2
2
18
18
2
2
785 x 155 x 185
785 x 155 x 185
8.3
8.3
Exit
(direction)
Straight
Through
Left
Right
Item Type
Catalogue No.
EXEN218EXIT24M
A
A
EXEN218EXITL24M
EXEN218EXITR24M
1
Hazardous Area Linear Lights
FLFE Fluorescent Linear Lights
Zones 1, 2 and 21, 22
IECEx CES 11.0021
Ex de IIC T6
Ex tb T70ºC to T80ºC
IP66
Ambient temp. / Temp. class / Max surface temp.
–20ºC +40ºC / T6/ 70ºC
–20ºC +50ºC / T6/ 75ºC
–20ºC +55ºC / T6/ 80ºC
Features and Benefits
•Shockproof borosilicate glass tube
•Ex e internal terminal junction box which allows connection with an Ex e cable gland (not barrier)
•Easy replacement of lamps
•Less wind resistance and less accumulation of dust
•Expanding range of LED models, including battery backup and emergency upon request
•EOL ballast (End Of Life)
•24V DC available upon request
Product Selection
Refer to page 22 for bracket selection.
LED models supplied with lamps
Fluorescent lamps not included
FLFE/L Standard LED Lights
Pwr Typ
(W)
22
Lumens
(lm)
4300
HxWxD
(mm)
1325 x 142 x 197
Weight
(kg)
9
HxWxD
(mm)
725 x 142 x 197
1325 x 142 x 197
1625 x 142 x 197
Weight
(kg)
5.2
7.5
10
Item Type
Catalogue No.
FLFE222L
FLFE Standard Lights
#Lamps
2
2
2
Lamp
(W max)
18
36
58
Item Type
Catalogue No.
FLFE-218
FLFE-236
FLFE-258
I
I
FLFE-218
FLFE Standard and / or Emergency Lights
FLFE emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping
during installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation. The operating time under emergency
operation, depending on requirements, can last from a minimum of 90 minutes to a maximum of 180 minutes.
#Lamps
2
2
Lamp
(W max)
18
36
BattDschrg
(hours)
2
1.5
HxWxD
(mm)
725 x 142 x 197
1325 x 142 x 197
Weight
(kg)
6.1
9
Item Type
Catalogue No.
I
I
FLFE-218EF4
FLFE-236EF4
FLFE-218EF4
FLFE Emergency Exit Lights
FLFE emergency exit lights are an effective guidance tool, convey important messages, provide a clear, easy-to-follow
directional system.
FLFE emergency series can operate in maintained or non-maintained operation as standard with use of terminals looping
during installation.
Fitted with a Ni-Cd battery and electronic inverter for use in emergency operation. The operating time under emergency
operation, depending on requirements, can last from a minimum of 90 minutes to a maximum of 180 minutes.
#Lamps
2
2
2
Lamp
(W max)
18
18
18
BattDschrg
(hours)
2
2
2
HxWxD
(mm)
725 x 142 x 197
725 x 142 x 197
725 x 142 x 197
Weight
(kg)
6.1
6.1
6.1
Exit
(direction)
Straight Through
Left
Right
Item Type
A
A
A
Catalogue No.
FLFE218EXIT24M
FLFE218EXITL24M
FLFE218EXITR24M
FLFE218EXIT24M
21
1
Hazardous Area Linear Lights
Linear Light Fitting Mounting Brackets
Mounting brackets suitable for the EXEL-L, EXEL, EXEN and FLFE range of Cortem fluorescent light fixtures.
Features and Benefits
•1 Bracket required per light fixture
Description
Item Type
20mm Inside Diameter Galvanised Steel Eye Bolt
K
GOF-8/K
Pole Mount Bracket Kit For Fluorescent Lighting Fixtures (EXEL, EXEN and FLFE Series) C/W Nuts
And Washers
K
G-0480/K
Cieling (Low-Profile) Mount Bracket Kit For Fluorescent Lighting Fixtures (EXEL, EXEN and FLFE
Series) C/W Nuts And Washers
K
G-244/K
Cieling (High-Profile) Mount Bracket Kit For Fluorescent Lighting Fixtures (EXEL, EXEN and FLFE
Series) C/W Nuts And Washers
K
G-263/K
Wall (45Deg) Mount Bracket Kit For Fluorescent Lighting Fixtures (EXEL, EXEN and FLFE Series)
C/W Nuts And Washers
K
G-258/K
G244K
G0480K
G258K
Dimensions (mm)
22
Catalogue No.
A
A1
B
C
Catalogue No.
725
640
135
190
FLFE218
1325
1240
135
190
FLFE236
725
640
135
190
FLFE218EF4
1325
1240
135
190
FLFE236EF4
1325
1240
135
190
FLFE222L
1
Hazardous Area Flood Lights
EVL LED Floodlights
Zones 1, 2 and 21, 22
IECEx ITS 14.0061
Ex de IIC Tx Gb
Ex tb IIIC Tx Db
IP66
EVL LED Floodlights
The new LED lighting fixtures EVL series has been developed with the aim of redefining the concepts of compactness, versatility and
ease of installation thanks to the new LED lighting system “COB” (ChipOnBoard).
This technology obtains high values of lumen output and the installation at low heights, without the risk of disturbing the operator.
Product Line Feature and Benefits
• 5 year warranty
EVL
series selection chart
VL series selection
chart
s in mm
• Lighting designs available, contact NHP for further information
42,45
• High efficiency with low
power usage compared42,45
to traditional light sources
THERMAL IMAGING EVL-70
THERMAL IMAGING EVL-70
40,0
40,0
a very brief
fixture10% of the cost of traditional Following
a very
initial period,
lighting
fixtureinitial period,
• Operating life of 100,000 hours
(20 years
for brief
12 hours
a Following
day) the
reducing
maintenance
tothe
anlighting
estimated
37,5
37,5
reaches
thermal
stability. This image shows the detected
reaches thermal stability.
This image
shows
the detected
lighting systems
heat. at
With
the(as
ambient
heat. With the ambient 35,0
temperature
18°C
showntemperature at 18°C (as shown
by the blue background)32,5
the LED lamp barely touches
42°C atwith
the hottest
42°C
the hottest
point.
Ex e internal terminal junction
boxatwhich
allows
connection
an Expoint.
e cable gland (not barrier)
30,0
30,0
This thermal
performance
This thermal performance is tangible
proof of
the high is tangible proof of the high
27,5
27,5
Very low operating temperature
efficiency
of LED lamps as a source of light.
efficiency of LED lamps as a source
of light.
25,0
25,0
It isofalso
noting
the
distributioncompared
of heat on the
fins
It
is
also
worth
noting
the
distribution
of worth
heat on
the fins
Excellent colour rendering (CRI), a measure of the quality
reproduction
of colour’s
to natural
sunlight.
22,5
22,5
thatThermal
are the result
of sophisticated Thermal Managethat are the result of sophisticated
ManageShockproof and vibration resistant
glass
ment.
ment. with toughened borosilicate
35,0
• 2x ISO M20 entries. Supplied with 1x PLG1IB Plug and 1by
REV1IB
cable gland
the blue background) the LED lamp barely touches
32,5
•
•
•
•
18,26
18,26
• Aluminum housing is designed with a finned body to efficiently dissipate heat and minimise dust accumulation
Type
Lamp
Code
Pwr Typ
EVL-60
LED (W)
LED 27EVL-70
53EVL-80
LED
86
EVL-100
LED
154
Watt
Type Class
Lamp(Ta = +40°C)
Lumens
LED
27 W (lm)
LED
53 W 3140
6564 LED
86 W
9732
LED
154 W
19125
T5/T6
T4
T4
T4
Watt Max surface
Class
temperature °C (Ta = +40°C)
Ue
(Ta = +40°C)
(V AC,27min
W - max)
85/100
120 - 277
53 W
135
120 - 277
86 W
135
220 - 240
154 W
135
100 - 277
DIMENSIONAL DRAWING
Weight Max surface
Kg temperature °C
H x W x D (Ta = +40°C)
mm Weight
(kg)
T5/T6(mm) 3,5
85/100
215x205x170
3.5
T4 170 x 170
135
5,2 x 210
250x235x165
220 x 220
x 192290x290x170
5.2
T4
135
7,2
265 x 265 x 216
7.2
T4
135
11,2
385x385x250
385 x 385 x 250
11.2
EVL-80
EVL-70
mm
3,5
215x205x170
Item Type
Catalogue No.
5,2
I
250x235x165
7,2
290x290x170
EVL60
EVL70
EVL80
EVL100
11,2
I
I
385x385x250
I
DIMENSIONAL DRAWING
EVL-100
EVL-60
EVL-70
Weight
Kg
EVL-100
EVL-80
Dimensions in mm
21
23
Hazardous Area Flood Lights
1
EWL LED Floodlights
Zones 1, 2 and 21, 22
IECEx ITS 11.0018
Ex d e IIC T5 Gb
Ex tb IIIC T100°C Db
IP66
Ambient temp. / Temp. class / Max surface temp.
–40ºC +60ºC / T5 / T100ºC
Features and Benefits
•Lighting designs available, contact NHP for further information
•High efficiency with low power usage compared to traditional light sources
•Operating life of 100,000 hours (20 years for 12 hours a day) reducing maintenance to an estimated 10% of the cost of traditional
lighting systems
•2x ISO M20 entries. Supplied with 1x PLG1IB Plug and 1 REV1IB Cable Gland
•Ex e internal terminal junction box which allows connection with an Ex e cable gland (not barrier)
•Very low operating temperature
•Excellent colour rendering (CRI), a measure of the quality of reproduction of colour’s compared to natural sunlight.
•Lens options (10°, 20°, 40° for narrow or wider light beams with higher light intensity, standard 120° beam angle)
•Shockproof and vibration resistant with toughened borosilicate glass
•Aluminium housing is designed with a finned body to efficiently dissipate heat and minimise dust accumulation
EWL LED Floodlights
The EWL series, utilises the latest in LED technology and drivers based on high-reliability products manufactured by one of the world’s
leading manufacturers.
The distinctiveness of these floodlights, available with optics of different angles (10°, 20°, 40°, 120°), is in their rigid body that is able to
withstand vibrations designed for the harshest environments.
These compact, extremely efficient floodlights are Ex de certified and are able to perform easily in extreme climates and environments.
EWL70 LED Floodlights
AC Supply
Pwr Typ
(W)
40
Lumens
(lm)
3700
Ue
(V AC, min - max)
198 - 264
Ue
(V DC, min - max)
-
Lumens
(lm)
3700
Ue
(V AC, min - max)
-
Ue
(V DC, min - max)
21.6 - 26.4
HxWxD
(mm)
270 x 215 x 340
Weight
(kg)
6.5
Item Type
Catalogue No.
EWL70
EWL70
DC Supply
Pwr Typ
(W)
40
EWL7024
24
HxWxD
(mm)
270 x 215 x 340
Weight
(kg)
6.5
Item Type
I
Catalogue No.
EWL7024
1
EWL80 LED Floodlights
AC Supply
Pwr Typ
(W)
65
Lumens
(lm)
6050
Ue
(V AC, min - max)
90 - 264
Ue
(V DC, min - max)
-
HxWxD
(mm)
292 x 260 x 343
Weight
(kg)
8.6
Item Type
Catalogue No.
EWL-80
EWL-../.. series selection chart
Code
DC Supply
Pwr Typ
EWL-70/10
(W)
65
EWL-70/20
EWL-70/40
Lens
type
Watt
Class
Lumens
Ue
Narrow (10°) (V AC, min
40W- max)
(lm)
6050
Medium (20°) 40W
Ue
T5 min - max)
(V DC,
21.6 T5
- 26.4
EWL-80
Max surface
temperature °C
HxWxD
100
(mm)
292100
x 260 x 343
40W
EWL-80/10
Narrow (10°)
55W
T5
100
8,6
EWL-80/20
Medium (20°)
55W
T5
100
8,6
EWL-80/40
Wide (40°)
55W
T5
100
8,6
EWL-801/10
100
Weight
(kg) 6,5
8.6 6,5
Wide (40°)
EWL100 LED Floodlights
T5
Weight
Kg
Narrow (10°)
110W
T5
100
8,6
Medium (20°)
110W
T5
100
8,6
Pwr Typ
EWL-801/40
Lumens
Wide (40°)
(lm)
Narrow (10°)
17000
17000
Medium (20°)
(W)
EWL-100/10
180
180
EWL-100/20
EWL-100/40
Wide (40°)
Ue 110W
(V AC, min - max)
188W
90 - 264
90 - 264
188W
188W
Ue T5
(V DC, min - max)
- T5
- T5
H x100
WxD
(mm)
100
407
x 385 x 483
407
x 385 x 483
100
T5
DIMENSIONAL DRAWING
EWL-70/...
100
I
Catalogue No.
EWL8024
6,5
EWL-801/20
AC Supply
mm
Item Type
Weight
8,6
(kg)
18,4
18.4
18.4
18,4
EWL8024
Item Type
I
Catalogue No.
EWL10040
EWL100
18,4
EWL10040
EWL-100/...
EWL-80../...
Dimensions in mm
43
25
1
Hazardous Area Flood Lights
SLEE Floodlights
Zones 1, 2 and 21, 22
IECEx TSA 08.0011
Ex de IIB + H2 T2 / T3
Ex tb T188ºC / 198ºC Db
IP65/66
Ambient temp. / Temp. class / Max surface temp.
20ºC to +40ºC / T3 / 188ºC
20ºC to +50ºC / T2 / 198ºC
Features and Benefits
•IP67
•150W, 250W and 400W for varying light output
•Low copper content aluminum body ensure better strength and corrosion resistant
•Shock and high temperature resistant tempered glass cover
•Easy installation, both vertical and horizontal, because of mobile supporting bracket
•Shock and high temperature resistant frontal tempered glass Product Selection
Lamps not included with fixture.
SLEE Fixtures
•Suitable for high pressure sodium vapour and metal halide lamps up to 400W
•Easy installation, both vertical and horizontal, because of mobile supporting bracket
•Low copper content aluminium body ensure better strength and corrosion resistant
•Strong and durable anodised aluminium reflector
•Shock and high temperature resistant frontal tempered glass
•Ral 7035 epoxy coating
•Neoprene sealings maintains flexibility over a wide temperature range
Lamp
Lamp
Ue
HxWxD
Weight
(type)
(W max)
(V AC, min - max)
(mm)
(kg)
Catalogue No.
Metal Halide
250
- 230
296 x 482 x 480
14.85
I
SLEE-40IM5
Metal Halide
400
- 230
296 x 482 x 480
20.38
I
SLEE-40IM6
SLEE-40IM5
Dimensions (mm)
Lamp type
Lamp power
Reflector
Weight (kg)
Catalogue No.
Metal halide
250 W
Symmetric
11.3
TIGER-250HA
Metal halide
400 W
Symmetric
13
TIGER-400HA
Spare parts
26
Item Type
Lamp type
Catalogue No.
Tempered glass cover
G-505
Lampholder
PORT E-40
1
Hazardous Area Flood Lights
TIGER Floodlights
Zones 2 and 21, 22
IECEx ITS 12.0004X
Ex nR IIC T3 / T2 Gc
Ex tc IIIC T174ºC / 210ºC Dc
IP66
Ambient temp. / Temp. class / Max surface temp.
-50ºC to +45ºC / T3 / 174ºC
-50ºC to +60ºC / T3 / 194ºC
-20ºC to +45ºC / T3 / 195ºC
-20ºC to +60ºC / T2 / 210ºC
Features and Benefits
•Tempered glass cover
•Fast maintenance
•Simple wiring thanks to the use of marked terminals
•Anti-corrosion aluminium clips
•Flat glass anti-light pollution
•Suitable for lamps up to 400W
•Symmetrical/asymmetrical reflectors available
Product Selection
Lamps not included with fixture.
TIGER Light Fixtures
Lamp
(type)
Metal Halide
Metal Halide
Lamp
(W max)
250
400
Ue
(V AC, min - max)
- 230
- 230
HxWxD
(mm)
530 x 430 x 200
530 x 430 x 200
Weight
(kg)
11.3
13
Item Type
Catalogue No.
I
I
TIGER-250HA
TIGER-400HA
Dimensions (mm)
A
B
C
a
b
Catalogue No.
296
482
480
174
291
SLEE-40I
296
458
355
174
266
SLEE-25N4
SLEE-40
SLEE-40 and SLEE-25
Max. surface
Lamp type
TIGER-250HA
Lamp power
Lamp holder
Temperature class
temperature C
Weight (kg)
Catalogue No.
Metal halide
250 W
E40
T3 / T3
200
14.85
SLEE-40IM5
Metal halide
400 W
E40
T3 / T2
200 / 300
20.38
SLEE-40IM6
High pressure sodium 400 W
E40
T4 / T3
135/200
14.85
SLEE-25N4
27
1
Hazardous Area Pendant Lights
EVE Pendant Lights
Zones 1, 2 and 21, 22
IECEx CES 07.0004
Ex d IIC T6 / T5 / T4 /T3 / T2
Ex de IIC T6 / T5 / T4 / T3 / T2
Ex tD A21
T85°C to T220 °C
IP66
Ambient temp. / Temp. class / Max surface temp.
–40ºC +40ºC / T5 / 65ºC
–40ºC +55ºC / T5 / 80ºC
–40ºC +60ºC / T4 / 85ºC
Features and Benefits
•LED version avilable with remote phosphor technology
•Suitable for indoor and outdoor installation
•Indirect cable entry is allowed
•Aluminium alloy body with low copper content ensures better strength and corrosion resistance
•Internal/external stainless steel earth screw
•Borosilicate glass globe has excellent thermal and mechanical properties
•Wiring through silicone rubber cables resistant up to 200°C
•Neoprene seals resistant to acids and hydrocarbons
•RAL 7035 grey epoxy powder coating for harsh environment
EVE Series
Lamp
(type)
LED
LED
LED
LED
EVEX-5050L
28
Lamp
(W max)
8
13
17
13
Ue
(V AC)
230
230
230
Ue
(V DC)
24
HxWxD
(mm)
260 x 150 x 150
322 x 170 x 170
322 x 170 x 170
322 x 170 x 170
Weight
(kg)
3
3.9
3.9
3.9
Item Type
Catalogue No.
I
I
I
I
EVEX-5050L
EVEX-5060L
EVEX-5060L1
EVEX5060L124
1
Hazardous Area Pendant Lights
EWAE Pendant Lights
Zones 1, 2 and 21, 22
IECEx CES 07.0004
Ex d IIC T6 / T5 / T4 /T3 / T2
Ex de IIC T6 / T5 / T4 / T3 / T2
Ex tD A21
T85°C to T220 °C
IP66
Ambient temp. / Temp. class / Max surface temp.
–40ºC +40ºC / T5 / 65ºC
–40ºC +55ºC / T5 / 80ºC
–40ºC +60ºC / T4 / 85ºC
Features and Benefits
•Suitable for indoor and outdoor installation
•Indirect cable entry is allowed
•Aluminium alloy body with low copper content ensure better strength and corrosion resistant
•Internal/external stainless steel earth screw
•Borosilicate glass globe has excellent thermal and mechanical properties
•Wiring through silicone rubber cables resistant up to 200°C
•Neoprene seals resistant to acids and hydrocarbons
•RAL 7035 grey epoxy powder coating
EWAE Series, Pendant Mount
80 Size
Lamp
(type)
Metal Halide
Lamp
(W max)
250
Ue
(V AC, min - max)
- 230
Ue
(V DC, min - max)
-
HxWxD
(mm)
643 x 235 x 235
Weight
(kg)
10.1
Item Type
Catalogue No.
I
EWAE-5080IM5
EWAE-5080IM5
100 Size
Lamp
(type)
Metal Halide
Lamp
(W max)
400
Ue
(V AC, min - max)
- 230
Ue
(V DC, min - max)
-
HxWxD
(mm)
710 x 265 x 265
Weight
(kg)
16.3
Item Type
Catalogue No.
EWAE-50100IM6
I
EWAES Series, Ceiling Mount
EWAE-50100IM6
100 Size
Lamp
(type)
Metal Halide
Lamp
(W max)
400
Ue
(V AC, min - max)
- 230
Ue
(V DC, min - max)
-
HxWxD
(mm)
710 x 265 x 265
Weight
(kg)
16.3
Item Type
I
Catalogue No.
EWAES-50100IM6
EWAES-50100IM6
Reflector
Dome Reflector
30° Inclined Reflector
Reflectors and other mounting options available upon request
29
2
Control Station and Junction Boxes
Selection Chart
32
Hazardous Area Control Stations
Cortem EFDC (Ex d) Control Stations
Standard Control Station
34
34
Hazardous Area Junction Boxes
S Series (Ex d) Junction Boxes
SA (Ex e) Junction Boxes
38
39
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
30
TERMINAL AND
JUNCTION BOXES
COMMAND AND
CONTROL OPERATORS
CONTROL STATIONS
31
2
Hazardous Area Control Stations and Junction boxes
Selection Chart
Description
Hazardous Area Control Stations
Zone 1
Zone 2
Zone 21
Zone 22
Group
Ex d
Ex tb
3
3
3
3
IIC
IIIC
Ex e
Ex tb
3
3
3
3
IIC
IIIC
Hazardous Area Junction Boxes
Cortem S…
• Available in aluminum or stainless steel
bodies
• Fully customisable options, contact NHP
for a quote today
• Drawings can be sent directly to NHP for
quotation
Ex d
Ex e
Ex ia
Ex tb
3
3
3
3
IIC
IIIC
Hazardous Area Junction Boxes
Cortem SA…
• Available in GRP, aluminum or stainless
steel bodies
• Fully customisable options, contact NHP
for a quote today
• Drawings can be sent directly to NHP for quotation
Ex e
Ex tb
Ex e ia
Ex tb ia
3
3
3
3
IIC
IIIC
Cortem EFDC
• Aluminium alloy enclosure
• Up to 4 operators on a single unit
• Fully customisable options, contact NHP
for a quote today
• Drawings can be sent directly to NHP for
quotations
Hazardous Area Control Stations
Cortem SA…
• Available in GRP, aluminum or stainless
steel bodies
• Up to 3 operators in standard
configurations
• Fully customisable options, contact NHP
for a quote today
• Drawings can be sent directly to NHP for
quotations
32
Protection
Technique
NTU takes on Hazardous Area Equipment!
If you haven’t already taken advantage of the NHP Training
University (NTU) training program, don’t wait any longer!
Other NTU modules now available include:
• Contactors and Overloads
The Hazardous Area Equipment module explains the basic
principle of explosion protection from area classifications to
temperature classes and the different types of protection
methods available.
• Motor Starters and Controllers
When it comes to selecting Hazardous Area Equipment for your
specific installation requirements, with NTU you’ll be covered.
• Machine Safety Control Systems
• NHP Smartphone Apps: Tradie Tools on the Go
• Fundamentals of Electricity
• Fundamentals of Electrical Equipment
Scan to download the
NHP eCatalogues App for
exclusive video content,
catalogues and literature!
Get switched on with NTU nhpntu.com
2
Hazardous Area Control Stations
Cortem EFDC (Ex d) Control Stations
Zones 1, 2 and 21, 22
IECEx TSA 6.0009
Ex d IIC T6
Ex tD A21 T85ºC
IP 65
EFDC series control stations are suitable for the signalling and the control of equipment installed on-board machines or at distance.
They are used in the chemical, petrochemical and pharmaceutical industries and in any other places where an explosion-proof
installation is required.
EFDC Series
#operators
Position 1
1
E-Stop, Mushroom Head, Twist to Release, Red, 1 NO + 1 NC
Item Type
LDC
Catalogue No.
NP2102D
EFDC21EMR
EFDC21EMR
Hazardous Area Control Stations
Standard Control Station
Zones 1, 2 and 21, 22
IECEx CES 11.0032
Ex de IIC T6 or T5 Gb
Ex tb IIIC T85°C or T100°C Db
IP66
Ambient Temp. / Temp. Class / Max Surface Temp.
- 40°C + 40°C / T6 / T85°C
- 40°C + 55°C / T5 / T100°C
Features and Benefits
•Available in GRP, aluminum or stainless steel bodies
•Up to 3 operators in standard configurations
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with
certification
•More sizes available upon request, anti-condensation paint available upon request.
•
Enclosures cannot be supplied blank
Product Selection
To determine cable entries, refer to suffix of part number; For example P12RZ(01):
01 – 1 x M20 Bottom
02 – 1 x M25 Bottom
09 – 2 x M20 Bottom
11 – 1 x M20 Top and Bottom
22 – 1 x M25 Top and Bottom
34
2
P - GRP Series
The P series control stations are assembled in enclosures made of polyester. They are designed according to increased safety Ex e or
dust protection Ex tb and can be equipped with the certified components like; pilot LED, contact blocks, command and signalling
actuators series, terminal blocks, instruments series etc.
Position 1
(operator)
Pushbutton,
Guarded/Booted,
Momentary, Black
E-Stop, Mushroom
Head, Twist to
Release, Red
E-Stop, Mushroom
Head, Twist to
Release, Red
Selector Switch,
Short Handle,
2-Position, Rotate,
Black
Selector Switch,
Short Handle,
2-Position, Rotate,
Black
Position 1
(contacts)
Position 2
(operator)
Position 2
(contacts)
Position 3
(operator)
Position 3
(contacts)
1 NO + 1 NC
Item Type
A
Catalogue No.
P1-1NZ-01
P1-2RW-01
1 NC
1 NO + 1 NC
A
P1-2RZ-01
2 NO
A
P1-52I-11
1 NO + 1 NC
A
P1-5Z-01
E-Stop, Mushroom
Head, Twist to
Release, Red
1 NO + 1 NC
A
P1-2RZ-01-G
E-Stop, Mushroom
Head, Twist to
Release, Red
2 NC
A
P1-2RY-09
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO
A
P2-1GV-1RW-01
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO + 1 NC
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO + 1 NC
Pushbutton,
Guarded/Booted,
Momentary, Green
1 NO + 1 NC
P1-2RZ-01
Pushbutton,
Guarded/
Booted,
Momentary, Red
Pushbutton,
Guarded/
Booted,
Momentary, Red
E-Stop,
Mushroom
Head, Twist to
Release, Red
E-Stop,
Mushroom
Head, Twist to
Release, Red
Pushbutton,
Guarded/
Booted,
Momentary, Red
E-Stop,
Mushroom
Head, Twist to
Release, Red
Configuration
Enclosure
Single gang
SA111108
Double gang
SA171108
Triple gang
SA301410
1 NC
P21GV1RW09
1 NC
1 NC
A
P2-1GV-2RW-01
1 NO + 1 NC
A
P2-1GZ-2RZ-01-P
1 NO + 1 NC
E-Stop, Mushroom
Head, Twist to
Release, Red
1 NO +
1 NC
A
P3-1GZ-1RZ-2RZ-02
1 NO + 1 NC
Selector Switch,
Short Handle,
3-Position, Rotate,
Black
2 NO
A
P3-1GZ-2RZ-51C-02
Dimensional information found on pg. 49
35
2
SA - Aluminium Series
The SA series control stations are assembled in enclosures made of aluminium. They are designed according to increased safety Ex e
or dust protection Ex tb and can be equipped with the certified components like; pilot LED, contact blocks, command and signalling
actuators series, terminal blocks, instruments series etc.
Position 1
(operator)
Pushbutton, Guarded/
Booted, Momentary, Black
E-Stop, Mushroom Head,
Twist to Release, Red
E-Stop, Mushroom Head,
Twist to Release, Red
E-Stop, Mushroom Head,
Twist to Release, Red
E-Stop, Mushroom Head,
Twist to Release, Red
Selector Switch, Short
Handle, 2-Position, Rotate,
Black
Selector Switch, Short
Handle, 2-Position, Rotate,
Black
Selector Switch, Short
Handle, 2-Position, Rotate,
Black
E-Stop, Mushroom Head,
Twist to Release, Red
Position 1
(contacts)
1 NO +
1 NC
Position 2
(operator)
Position 3
(contacts)
1 NC
1 NO +
1 NC
1 NO +
1 NC
Item Type
Catalogue No.
A
A1-1NZ-01
A
A1-2RW-01
A12RZ01
A
A12RZ02
2 NC
A
A1-2RY-09
2 NO
A
A1-52I-01
2 NO
A
A1-52I-09
2 NO
A
A1-52I-11
1 NO +
1 NC
A
A1-2RZ-01-G
A
A2-1GV-1RW-01
Pushbutton,
Guarded/Booted,
Momentary, Red
Pushbutton,
Guarded/Booted,
Momentary, Red
E-Stop, Mushroom
Head, Twist to
Release, Red
E-Stop, Mushroom
Head, Twist to
Release, Red
Selector Switch,
Short Handle,
2-Position, Rotate,
Black
Pushbutton,
Guarded/Booted,
Momentary, Red
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO +
1 NC
Selector Switch, Short
Handle, 2-Position, Rotate,
Black
2 NO
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO +
1 NC
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO +
1 NC
Pushbutton,
Guarded/Booted,
Momentary, Red
1 NO +
1 NC
Pushbutton, Guarded/
Booted, Momentary, Green
1 NO +
1 NC
E-Stop, Mushroom
Head, Twist to
Release, Red
1 NO +
1 NC
Configuration
Enclosure
Single gang
SA111108P
Double gang
SA171108P
Triple gang
SA301410P
Dimensional information found on pg. 49
36
Position 2 Position 3
(contacts) (operator)
1 NC
A21GV1RW09
1 NC
1 NC
A
A2-1GV-2RW-01
1 NO +
1 NC
A
A2-1GZ-2RZ-01-P
2 NO
A
A2-52I-52I-01
A
A31GZ1RZ4G222
1 NO +
1 NC
A
A3-1GZ-1RZ-2RZ-02
2 NO
A
A3-1GZ-2RZ-51C-02
1 NO +
1 NC
Pilot Light,
Green
E-Stop,
Mushroom
Head, Twist to
Release, Red
Selector
Switch, Short
Handle,
3-Position,
Rotate, Black
2
Position 1
(operator)
Position 1
(contacts)
Position 2
(operator)
Position 2
(contacts)
Position 3
(operator)
1 NO +
1 NC
Pushbutton,
Guarded/
Booted,
Momentary,
Red
1 NO +
1 NC
Pilot Light,
Green
Pushbutton,
Guarded/Booted,
Momentary,
Green
1 NO +
1 NC
Pushbutton,
Guarded/
Booted,
Momentary,
Red
1 NO +
1 NC
E-Stop,
Mushroom
Head, Twist
to Release,
Red
Pushbutton,
Guarded/Booted,
Momentary,
Green
1 NO +
1 NC
E-Stop,
Mushroom
Head, Twist to
Release, Red
1 NO +
1 NC
Selector
Switch, Short
Handle,
3-Position,
Rotate, Black
Pushbutton,
Guarded/Booted,
Momentary,
Green
Position 3
(contacts)
Item Type
Catalogue No.
A
A31GZ1RZ4G222
1 NO + 1 NC
A
A3-1GZ-1RZ-2RZ-02
2 NO
A
A3-1GZ-2RZ-51C-02
SS - Stainless Steel Series
The SS series control stations are assembled in enclosures made of 316 stainless steel. They are designed according to increased
safety Ex e or dust protection Ex tb and can be equipped with the certified components like; pilot LED, contact blocks, command and
signalling actuators series, terminal blocks, instruments series etc.
Position 1
(operator)
Twist to Release, Red
Position 1
(contacts)
2 NC
Configuration
Enclosure
Single gang
SA111108SS
Double gang
SA171108SS
Item Type
Catalogue No.
S12RY01
Dimensional information found on pg. 50
Fully customisable options available call NHP
37
2
Hazardous Area Junction Boxes
S Series (Ex d) Junction Boxes
Zones 1, 2 and 21, 22
IECEx CES 14.0018X
Ex d IIC T... Gb
Ex e IIC T... Gb
Ex Ia IIC T... Gb
Ex tb IIIC T°C Db
IP66/67
Features and Benefits
•Available in aluminum or stainless steel bodies
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with
certification
•
Enclosures cannot be supplied blank
SF Series (Ex d) Junction Boxes
SFX141I
38
Terminals
(qty)
Earth Term
(qty)
Cable Entries
Ø Diameter
(mm)
Weight
(kg)
6
6
6
2
2
2
4 x M20
4 x M20
4 x M25
90
130
130
0.3
0.6
0.6
Item Type
I
Catalogue No.
SFX141I
SFX161I
SFX261I
2
Hazardous Area Junction Boxes
SA (Ex e) Junction Boxes
Zones 1, 2 and 21, 22
IECEx CES 13.0001
Ex e IIC T6 or T5 Gb
Ex tb IIIC T85º or T100º Db
Ex e ia IIC T6 or T5 Gb
Ex tb ia IIIC T85ºC or T100ºC Db
IP66
Ambient Temp. / Temp. Class / Max Surface Temp.
- 50°C + 40°C / T6 / T85°C
- 50°C + 55°C / T5 / T100°C
GRP Junction Boxes
The junction box series consists of enclosures made in GRP with Ex e and Ex tb protection for increased safety. There are six
terminals as well as two earthing terminals 4 mm2 and cable entries are managed by 4xM20-2 plugs. Alternative terminal
arrangements, sizes and numbers are available upon request.
Terminals
(qty)
6
Earth Term
(qty)
2
Cable Entries
4 x M20
HxWxD
(mm)
110 x 110 x 83
Item Type
Catalogue No.
PJB164420
PJB164420
Aluminium Junction Boxes
The junction box series consists of enclosures made in aluminium with Ex e and Ex tb protection for increased safety. There
are six terminals as well as two earthing terminals 4 mm2 and cable entries are managed by 4xM20-2 plugs. Alternative terminal
arrangements, sizes and numbers are available upon request.
Terminals
(qty)
6
Earth Term
(qty)
2
Cable Entries
4 x M20
HxWxD
(mm)
110 x 110 x 85
Item Type
Catalogue No.
A-JB-164-420
A-JB-164-420
Stainless Steel Junction Boxes
The junction box series consists of enclosures made in stainless steel with Ex e and Ex tb protection for increased safety. There are six
terminals as well as two earthing terminals 4 mm2 and cable entries are managed by 4xM20-2 plugs. Alternative terminal arrangements,
sizes and numbers are available upon request.
Terminals
(qty)
6
9
Earth Term
(qty)
2
2
Cable Entries
4 x M20
4 x M20
HxWxD
(mm)
120 x 120 x 80
147 x 147 x 110
Item Type
A
A
Catalogue No.
SJB164420
SJB194420
SJB164420
39
3
Custom Enclosures
Selection Chart 42
Hazardous Area Motor Starters
Cortem EJB Motor Starters
Cortem Ex d Custom Assemblies
Cortem (Ex e) Custom Assemblies
46
47
49
Command and Control Operators
50
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
40
TERMINAL AND
JUNCTION BOXES
COMMAND AND
CONTROL OPERATORS
MOTOR STARTERS
CUSTOM ASSEMBLIES
41
3
Hazardous Area Custom Enclosures
Selection Chart
Description
Hazardous Area Custom Enclosures
Protection
Technique
Zone 0
Zone 1
Zone 2
3
Ex d
Ex tb
• Available in aluminum bodies
Ex d
• Glass window available
Ex tD
• Fully customisable options, contact NHP for a quote today
• Drawings can be sent directly to NHP for quotation
Zone 20
Zone 21
Zone 22
Group
3
3
3
IIC
IIIC
3
3
3
3
I
IIC
IIIC
3
3
3
3
IIC
IIIC
Ex d
Ex tD
3
3
3
3
IIC
IIIC
Ex d
Ex tD
3
3
3
3
IIC
IIIC
Cortem Ex d Custom Assemblies
Cortem EJB
• Available in aluminum or stainless Ex d [ia]
steel bodies
Ex tb [ia]
• Glass window available
• Fully customisable options, contact NHP for a quote today
• Drawings can be sent directly to NHP for quotation
Hazardous Area Motor Starters
• Cast aluminium housing or Stainless Steel
•VSDs
• Soft Starters
• DOL, Star-delta and reverse starters
• Glass window available
• Fully customisable options, contact NHP for a quote today
• Drawings can be sent directly to NHP for quotation
Cortem GUB
Cortem CCA
• Available in aluminum bodies
• Fully customisable options, contact NHP for a quote today
• Drawings can be sent directly to NHP
for quotation
Ex d Operators
• Cortem M0…
• Emergency Stops
•Pushbuttons
• Indicator Lamps
• Mechanical Operators
42
3
Hazardous Area Custom Enclosures
Selection Chart
Description
Cortem Ex e Custom Assemblies
Cortem SA…P
• Glass reinforced Polyester Housing
• Fully customisable options
• Large range of operators, indicators and accessories
Protection
Technique
Zone 0
Zone 1
Zone 2
Zone 20
Zone 21
Zone 22
Group
Ex e [ia]
Ex tb [ia]
3
3
3
3
3
3
IIC
IIIC
Ex e [ia]
Ex tb [ia]
3
3
3
3
3
3
IIC
IIIC
Ex e [ia]
Ex tb [ia]
3
3
3
3
3
3
IIC
IIIC
3
3
3
3
IIC
IIIC
Cortem SA…
• Aluminium Housing
• Fully customisable options
• Large range of operators, indicators and accessories
Cortem SA…SS
• Stainless Steel Housing
• Fully customisable options
• Large range of operators, indicators and accessories
Ex e Operators
• Cortem M0…
• Emergency Stops
•Pushbuttons
• Indicator Lamps
• Ammeters and Voltmeters
Ex e
Ex tD
Typical examples of custom assemblies
include the following:
• Control stations
• Terminal boxes
• Full panel and frame design and construction (in both Ex d and Ex de technologies)
• Distribution panels
• Motor control
• Control stations
• Automation and DCS solutions
• Specialist process and
instrumentation requirements
43
3
Hazardous Area Custom Enclosures
Cortem Ex d Custom Assemblies
Features and Benefits
Typical examples of custom assemblies include the following:
•Control stations
•Terminal boxes
•Full panel and frame design and construction (in both Ex d and Ex de technologies)
•Distribution panels
•Motor control
•Control stations
•Automation and DCS solutions
•Specialist process and instrumentation requirements
Product Selection
Ex d enclosures are used for installation of electrical equipment such as circuit breakers and power distribution equipment, operators,
Indicators, PLC’s, DCS, control equipment, transformers, motor starters, terminals, process devices, intrinscally safe equipment and more.
Ex d enclosures can also be fitted with custom glass windows.
Contact NHP for a quote today.
Cortem EJB (Ex d) Custom Assemblies
Zones 1, 2 and 21, 22
IECEx TSA 06.0011
Ex d [ia Ga] IIB + H2 Gb T4/T5/T6
Ex tb [ia Da] IIIC Db
IP66/67
Ambient Temperature
- 20°C + 55°C
•Available in aluminum or stainless steel bodies and with windows
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with certification
•More sizes available upon request, anti-condensation paint available upon request
•Enclosures cannot be supplied blank
EJB Series
Solid Lid
EJB-1A
HxWxD
(mm)
304 x 204 x 218
364 x 284 x 278
364 x 284 x 218
567 x 387 x 298
567 x 387 x 248
710 x 510 x 356
710 x 510 x 256
632 x 432 x 341
632 x 432 x 271
870 x 650 x 380
Internal H x W x D
(mm)
240 x 140 x 153
300 x 220 x 213
300 x 220 x 153
490 x 305 x 229
490 x 305 x 179
630 x 430 x 273
630 x 430 x 173
560 x 360 x 275
560 x 360 x 203
760 x 540 x 253
Fixings H x W
(mm)
230 x 210
290 x 290
290 x 290
360 x 356
360 x 356
600 x 490
600 x 490
550 x 430
550 x 430
680 x 580
Weight
(kg)
10.3
19.4
16.4
38.9
35.3
81.3
66.9
51
43.4
138.5
Internal H x W x D
(mm)
214 x 113 x 60
240 x 140 x 160
360 x 260 x 233
490 x 305 x 210
490 x 305 x 160
560 x 360 x 256
Fixings H x W
(mm)
160 x 154
230 x 130
350 x 330
360 x 236
360 x 236
350 x 550
Weight
(kg)
5.6
9.4
25.4
36.5
33.1
49.8
Item Type
Catalogue No.
EJB-1A
EJB-3A
EJB45BA
EJB-45A
EJB45BA
EJB-55
EJB-55B
EJB-5A
EJB5BA
EJB6B
I
I
I
Ribbed Lid
HxWxD
(mm)
282 x 182 x 105
304 x 204 x 218
432 x 332 x 299
567 x 387 x 298
567 x 387 x 248
632 x 432 x 341
Item Type
Catalogue No.
EJB01
EJB1
EJB-4
EJB-45
EJB-45B
EJB-5
I
I
Accessories
NHP offer a comprehensive range of accessories and spare parts that are available on request.
Description
EJB Round Window Diameter 90mm
EJB Round Window Diameter 140mm
EJB Round Window Diameter 180mm
44
Item Type
I
I
I
Catalogue No.
K0253
K0254
K0255
NHP’s IECEx certified workshop
NHP supplies not only the Cortem
range of Hazardous Area Equipment,
but also, customer specific systems
via our assembly workshop located
at our National Distribution and
Manufacturing Centre in Melbourne.
In this workshop, accredited staff
design, construct and inspect the
Cortem range according to the
requirements of IECEx certification.
It allows for flexibility to produce
custom solutions to suit your HAE
requirements
The NHPEx workshop enables both
expeditious and effective solutions for
including:
customers and operates under stringent
quality assurance guidelines.
• Specialist lighting requirements
• Control stations (including custom orders)
NHPEx can assemble the following to
customer specifications:
• Terminal boxes (including custom orders)
• Distribution panels
• Full panel design and construction
(in both Ex d and Ex de technologies)
• Motor control
• Control stations
• Automation solutions
NHP ELECTRICAL ENGINEERING PRODUCTS
1300 NHP NHP | nhp.com.au |
3
Hazardous Area Motor Starters
Cortem EJB Motor Starters
EJB1A4DOL7
Zones 1, 2 and 21, 22
IECEx TSA 06.0011
Ex d [ia Ga] IIB + H2 Gb T4/T5/T6
Ex tb [ia Da] IIIC Db
IP66/67
Ambient Temp.
- 20°C + 55°C
NHP has a range of ‘off the shelf’ Ex motor starters that are available in various combinations.
NHP also offers customer specific systems via our assembly workshop located at our National Distribution and Manufacturing
Centre in Melbourne.
With over 40 years experience and knowledge in motor control combined with the quality solutions offered from our IECEx certified
workshop, NHP can offer a solution for all your motor control requirements.
Features and Benefits
•Cast aluminium housing
•IP65/66
•VSDs
•DOL, star-delta and reverse starters
•Distribution panels
•Glass window available
•Stainless steel version available
•Drawings can be sent directly to our estimating team for an immediate quote
Ex d DOL Motor Starters
As standard the Ex d DOL starters are supplied with:
• Start pushbutton
• Stop pushbutton
• Overload with DIP switch adjustable trip classes
• Class 10, 15, 20 and 30 to suit various load run-up times
• DIP switch adjustable auto/manual reset
NormalDuty
(kW)
7.5
15
Un
(V AC)
415
415
HxWxD
(mm)
304 x 204 x 218
304 x 204 x 218
Cortem GUB (Ex d) Custom Assemblies
GUB
GUB...B
46
Fixings H x W
(mm)
230 x 130
230 x 130
Weight
(kg)
10.3
10.3
Item Type
Catalogue No.
A
A
EJB1A4DOL7
EJB1A4DOL15
Zones 1, 2 and 21, 22
IECEx TSA 06.0012
Ex d IIC
Ex tD A21
IP66/67
Ambient Temperature
- 20°C + 55°C
•Available in Aluminum bodies
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with certification
•More sizes available upon request, anti-condensation paint available upon request
• Enclosures cannot be supplied blank
3
GUB Series
HxWxD
(mm)
Internal H x W x D
(mm)
Fixings H x W
(mm)
Weight
(kg)
174 x 174 x 140
276 x 276 x 217
146 x 146 x 78
250 x 250 x 135
150 x 195
236 x 316
3.9
11.92
Item Type
Catalogue No.
GUB-01
GUB-03
I
GUB-01V
GUB...V Series
HxWxD
(mm)
174 x 174 x 160
230 x 230 x 154
276 x 276 x 200
Internal H x W x D
(mm)
146 x 146 x 105
204 x 204 x 95
250 x 250 x 140
Fixings H x W
(mm)
154 x 195
196 x 265
236 x 316
Weight
(kg)
4.27
7.6
14.1
Window Ø
(mm)
90
140
180
Item Type
I
I
Catalogue No.
GUB-01V
GUB-02V
GUB0-3V
GUB...B
CCA (Ex d) Custom Assemblies
Zones 1, 2 and 21, 22
IECEx TSA 06.0012
Ex d IIC
Ex tD A21
IP66/67
Ambient Temp.
- 20°C + 55°C
•Available in aluminum bodies
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with certification
•More sizes available upon request, anti-condensation paint available upon request
• Enclosures cannot be supplied blank
CCA/E Series
H x W x D, Ø
(mm)
145 x 145 x 135, Ø170
195 x 195 x 159, Ø220
240 x 240 x 230, Ø270
128 x 128 x 133, Ø146
Internal H x W x D
(mm)
121 x 121
171 x 171
216 x 216
104 x 104
Fixings H x W
(mm)
128 x 150
175 x 175
213 x 213
111 x 138
Weight
(kg)
2.8
5.6
9.1
1.85
Internal H x W x D
(mm)
121 x 121 x 113
171 x 171 x 130
216 x 216 x 185
353 x 353 x 200
104 x 104 x 122
Fixings H x W
(mm)
128 x 150
175 x 175
213 x 213
339 x 339
111 x 138
Weight
(kg)
5
8
14
33
4
Item Type
I
I
I
I
Catalogue No.
CCA-01E
CCA-02E
CCA-03E
CCA0E
CCA/C Series
H x W x D, Ø
(mm)
145 x 145 x 149, Ø170
195 x 195 x 166, Ø212
240 x 240 x 223, Ø260
385 x 385 x 262, Ø410
128 x 128 x 150, Ø146
Item Type
I
I
I
I
I
Catalogue No.
CCA-01C
CCA-02C
CCA-03C
CCA-04C
CCA-0C
CCA-01C
47
3
Cortem EJB (Ex d) Custom Assemblies
Zones 1, 2 and 21, 22
IECEx TSA 06.0015U
Ex d IIC
Ex tD A21 IP66
M-0 series control, monitoring and signaling devices are installed as external accessories on Cortem ‘Ex d’ enclosures used in any
industrial environment where an explosive atmosphere may be present, classified as Zone 1, 2, 21, 22.
M-0 control devices can be used to close or open electrical or mechanical devices fitted inside the ‘Ex d’ enclosures while the signaling
devices feature lights to indicate their operating status. The control and signaling device components are made from stainless steel to
deliver unbeatable efficiency under any environmental conditions. Levers are made from aluminium while the plastic parts on pushbuttons are designed to provide lengthy service life even when used in a highly corrosive atmosphere.
M-0 control and signaling devices have an IP66 protection degree. All identification, test or warning labels located on the enclosure lids
are made from aluminium, stainless steel or traffolyte depending on your specific requirements or as dictated by our own standards.
Operator
(type)
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Operator
(action)
Momentary
Momentary
Momentary
Momentary
Momentary
Momentary
Operator
(colour)
Blue
White
Yellow
Black
Red
Green
Operator
(type)
Pushbutton, Extended, Illuminated
Pushbutton, Extended, Illuminated
Pushbutton, Extended, Illuminated
Pushbutton, Extended, Illuminated
Pushbutton, Extended, Illuminated
Operator
(action)
Momentary
Momentary
Momentary
Momentary
Momentary
Operator
(colour)
Blue
Yellow
White
Red
Green
Operator
(type)
E-Stop, Mushroom Head
Operator
(action)
Twist to Release
Operator
(colour)
Red
Operator
(type)
Multi-Function Pushbutton, 2-Position
Operator
(action)
Momentary
Colours
(top-bottom)
Red - Black
Operator
(type)
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Un
(V AC / V DC)
230V AC / 230V DC
24V AC / 24V DC
230V AC / 230V DC
230V AC / 230V DC
24V AC / 24V DC
230V AC / 230V DC
24V AC / 24V DC
Lens
(colour)
Blue
Blue
Yellow
Red
Red
Green
Green
Item Type
Catalogue No.
M-0429/B
M-0429/BI
M-0429/G
M-0429/N
M-0429/R
M-0429/V
I
I
M-0429
M-0428
M-0445
M-0427
Contacts
2 NC
Contact
(action)
Slow Action
Description
Padlockable 90 Int 3 R-Ms-Mo
Operator For Padlockable Cam And Rotary
Protection Guard And Mushroom Padlockable
Emergency Stop Guard
48
Contact
(type)
Double Break
Ue (max)
(V AC / V DC)
600 / 300
Item Type
Catalogue No.
M-0428/B
M-0428/G
M-0428/I
M-0428/R
M-0428/V
I
I
I
I
Item Type
Catalogue No.
M-0445
Item Type
I
Catalogue No.
M-0427
Item Type
Catalogue No.
I
I
M-0457/2B230
M-0457/2B24
M-0457/2G230
M-0457/2R230
M-0457/2R24
M-0457/2V230
M-0457/2V24
Item Type
Catalogue No.
M-0606/02
Item Type
I
I
Catalogue No.
M-0437/V
M-0438/V
M-736
M-952
3
Hazardous Area Custom Enclosures
Cortem SA (Ex e) Custom Assemblies
Zones 1, 2 and 21, 22
IECEx CES 11.0032
Ex de IIC T6 or T5 Gb
Ex tb IIIC T85°C or T100°C Db
IP66
Ambient Temp. / Temp. Class / Max Surface Temp.
- 40°C + 40°C / T / T85°C
- 40°C + 55°C / T5 / T100°C
Features and Benefits
•Available in GRP, aluminum or stainless steel bodies
•Fully customisable options, contact NHP for a quote today
•Drawings can be sent directly to NHP for quotation
•Can be drilled and assembled by the NHP IECEx workshop according to customers’ specification and in accordance with
certification
•More sizes available upon request, anti-condensation paint available upon request
•Enclosures cannot be supplied blank
Cortem SA (Ex e) Custom Assemblies
GRP Series
SA/P series terminal boxes consist of enclosures made in Glass Reinforced Plastic (GRP) with Ex e and Ex tb protection for increased safety.
They are equipped with Ex e terminals for circuits with Ex e or Ex ia or combinations of both. The cover is fixed to the body with 4, 6 or 8
anti-loosening screws and is IP 66 rated.
•SA/P series junction boxes are built in GRP resin
•Can be supplied with multipolar terminal blocks or with modular terminal blocks
•Can be equipped with pilot lights, pushbuttons and measuring instruments to assemble control and signaling panel stations
HxWxD
(mm)
110 x 110 x 83
170 x 110 x 83
305 x 147 x 110
Internal H x W x D
(mm)
104 x 104 x 65
164 x 104 x 65
296 x 138 x 90
Fixings H x W
(mm)
94 x 94
154 x 94
285 x 127
Weight
(kg)
0.4
0.7
1.9
Item Type
Catalogue No.
SA111108P
SA111108P
SA117108P
SA301410P
Aluminium Series
The SA series terminal boxes consist of enclosures made in aluminium with Ex e and Ex tb protection for increased safety.
They are equipped with Ex e terminals for circuits with Ex e or Ex ia or combinations of both. The cover is fixed to the body with
4, 6 or 8 anti-loosening screws.
•SA series junction boxes are constructed of aluminium alloy
•Can be supplied with multipolar terminal blocks or with modular terminal blocks
•Can be equipped with pilot lights, pushbuttons and measuring instruments to assemble control and signaling panel stations
HxWxD
(mm)
110 x 110 x 83
170 x 110 x 83
305 x 147 x 110
Internal H x W x D
(mm)
104 x 104 x 64
164 x 104 x 65
296 x 138 x 90
Fixings H x W
(mm)
94 x 94
154 x 94
285 x 127
Weight
(kg)
0.5
0.8
2
Item Type
Catalogue No.
SA111108
SA111108
SA171108
SA301410
49
3
Stainless Steel Series
The SA / SS series terminal boxes consist of enclosures made in stainless steel with Ex e and Ex tb protection for increased safety.
They are equipped with Ex e terminals for circuits with Ex e or Ex ia or combinations of both. The cover is fixed to the body with
4, 6 or 8 anti-loosening screws.
•SA...SS series junction boxes are constructed from AISI 316L stainless steel
•Suitable for electrical installations placed in aggressive environments as increased safety boxes
•Can be supplied with multipolar terminal blocks or with modular terminal blocks
•Can be equipped with pilot lights, pushbuttons and measuring instruments to assemble control and signaling panel stations
SA1007030SS
HxWxD
(mm)
1000 x 700 x 300
110 x 110 x 90
170 x 110 x 90
200 x 200 x 210
305 x 230 x 190
400 x 400 x 210
500 x 500 x 210
600 x 600 x 210
620 x 305 x 190
Internal H x W x D
(mm)
940 x 640 x 255
67 x 67 x 37
127 x 67 x 37
145 x 145 x 155
249 x 174 x 135
344 x 344 x 155
445 x 445 x 155
545 x 545 x 155
564 x 249 x 135
Fixings H x W
(mm)
464 x 740
38 x 130
98 x 130
128 x 220
233 x 250
328 x 420
428 x 520
528 x 620
548 x 325
Item Type
Catalogue No.
I
I
SA1007030SS
SA111108SS
SA171108SS
SA202020SS
SA302318SS
SA404020SS
SA505020SS
SA606020SS
SA623018SS
I
I
I
I
I
I
Cortem (Ex e) command and control operators
Zones 1, 2 and 21, 22
IECEx CES 11.0029U
Ex e IIC Gb
Ex tb IIIC Db IP 66
M-0 series control, monitoring and signaling devices are installed as external accessories on Cortem ‘Ex e’ enclosures used in any
industrial environment where an explosive atmosphere may be present, classified as Zone 1, 2, 21, 22.
M-0 control devices can be used to close or open electrical or mechanical devices fitted inside the ‘Ex e’ enclosures while the signaling
devices feature lights to indicate their operating status.
Devices have an IP66 protection degree.
All identification, test or warning labels located on the enclosure lids are made from aluminium, stainless steel or traffolyte depending
on your specific requirements or as dictated by our own standards.
•High mechanical strength
•High operational reliability and cost efficiency
•Reduced maintenance costs
•Rated voltage: 690V
•Frequency: 50/60Hz
•Range: 10A
•Connection: max. 2.5mm2
•Rated impulse withstand voltage: 4kV
•Pollution degree: 2
•Short circuit conditional current : 1kA
•Minimum positive opening travel: 3mm
•Minimum force required for operation: 5N
•Maximum stroke (+ overtravel): 4.75mm
•Weight: 40g
M-0603/R
Operator
(type)
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Pushbutton, Flush
Operator
(type)
E-Stop, Mushroom Head
E-Stop, Mushroom Head
M-0605
50
Operator
(action)
Momentary
Momentary
Momentary
Momentary
Momentary
Momentary
Momentary
Operator
(colour)
Blue
White
Yellow
Black
Red
Red
Green
Operator
(action)
Push-Pull / Twist to Release
Key to Release
Padlockable
(Y / N)
No
No
No
No
No
Yes
No
Operator
(colour)
Red
Red
Item Type
Catalogue No.
M-0603/B
M-0603/BI
M-0603/G
M-0603/N
M-0603/R
M-0603/RL
M-0603/V
I
I
I
I
Item Type Catalogue No.
I
M-0605
M-0605/K
Operator
(type)
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Pilot Light
Un
(V AC / V DC)
230V AC /
24V AC / 24V DC
230V AC /
24V AC / 24V DC
230V AC /
24V AC / 24V DC
230V AC /
24V AC / 24V DC
Operator
(colour)
Blue
Blue
Yellow
Yellow
Red
Red
Green
Green
Description
Contacts
CONTACTS SET 1NC
CONTACTS SET 1NO CONTACTS
CONTACTS SET 1NO+1NC
1 NC
1 NO
1 NO + 1 NC
Operator
(type)
Selector Switch, Short Handle,
3-Position
Selector Switch, Short Handle,
2-Position
Selector Switch, Short Handle,
3-Position
Selector Switch, Short Handle,
2-Position
Item Type
Catalogue No.
I
I
I
I
I
I
I
I
M-0612/B230
M-0612/B24
M-0612/G230
M-0612/G24
M-0612/R230
M-0612/R24
M-0612/V230
M-0612/V24
Item Type
3
M-0612/V
Catalogue No.
M-0606/01
M-0606/10
M-0606/11
Operator
(action)
Operator
(colour)
Latched / Maintained
Black
Latched / Maintained
Black
Spring Return
Black
I
M-0604/2W
Latched / Maintained
Black
I
M-0604/2Z
Item Type
I
Catalogue No.
M-0604/2C
M-0604/2I
M-0604/01
Description
Ex E Selector Switch Lockout Bar
Item Type
Catalogue No.
M963
51
2
4
Intrinsic Safety Equipment
Hazardous Area Intrinsically Safe Isolators
GM International Intrinsically Safe Isolators
54
Hazardous Area Intrinsically Safe Distributed I/O
57
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
52
INTRINSICALLY SAFE
GALVANIC ISOLATORS
INTRINSICALLY SAFE
GALVANIC ISOLATORS
INTRINSICALLY SAFE
DISTRIBUTED I/O
53
4
Hazardous Area Intrinsically Safe Isolators
GM International Intrinsically Safe Isolators
Zones 0, 1, 2 and 20, 21, 22
Ambient temperature
-40°C to +60/+70 °C
The entire D1000 and D5000 series are IECEx certified and approved for maritime applications by DNV and KR.
Multiple output configurations allow for a wide range of applications, interfacing the majority of devices on the market.
Majority of iS isolators in the range are DIP switch configurability for easy field setup.
Software configurable isolators, e.g the 8 channel digital Input module D5231 offers modbus output which gives the possibility
to read and configure the barrier remotely.
Contact NHP for assistance with:
• Matching devices to associated apparatus
• Assessment of intrinsically safe systems
• Entity calculations
• Ex loop safety parameters verification
Features and Benefits
Wide functionality
•Wide range of digital and analogue I/Os
•More than 25 modules suitable for SIL 3 applications according to IEC 61508, IEC 61511
High performance
•Complete absence of electrolytic capacitors and SMD manufacturing ensures minimum 20 years lifetime
•High signal transfer accuracy and repeatability
General features
•Installation in Zone 2
•High packing density
•Three port galvanic isolation to eliminate noise, ground loop problems and to provide intrinsic safety without a high integrity
safety earth connection
•Line fault alarm detects open or short circuit of field cables
•Certified for offshore and marine applications
D1000 Series
The GM International D1000 series intrinsically safe isolators have a wide range of functions, suitable for multiple applications from
analogue in and out, digital in and out, temperature converters and trip converters, serial converters, load cell, encoders and more.
D1000 Modules provide the most simple and cost effective means of implementing intrinsic safety into your Hazardous Areas/locations
applications.
If Bus mounting is required, please contact NHP for quote.
Digital Input
D1000 Series Digital input isolators.
Channels
2
2
D1030D
2
Item Type
54
Hazardous
Area
(signal)
Voltage Free
Input
Proximity
Switch
Voltage Free
Input
Proximity
Switch
Voltage Free
Input
Proximity
Switch
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
CO Relay,
Isolated
-
20 - 30
SIL 2
D1030D
CO Relay,
Isolated
-
10 - 30
SIL 2
D1031D
CO Relay,
Isolated
85 - 250
-
SIL 2
D1130D
Item Type
Catalogue No.
4
Digital Outputs
D1000 Series digital output driver isolators.
Channels
4
4
Hazardous Area
(signal)
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
CO Relay (I and V
Limited)
CO Relay (I and V
Limited)
Voltage Free
Input
Voltage Free
Input
-
21.5 - 30
SIL 3
-
21.5 - 30
SIL 3
Item Type
Catalogue No.
D1042Q
I
D1043Q
D1042Q
D1000 Series Load Cell Isolators
D1000 series load cell isolators.
1
Hazardous Area
(signal)
Resistance
1
Resistance
Channels
Safe Area
(signal)
Resistance
Current:
Single-Ended,
Isolated
Voltage:
Single-Ended,
Isolated
Ue
(V AC min - max)
-
Ue
(V DC min - max)
20 - 30
-
-
Item Type
Catalogue No.
D1063S
D1064S
I
D1063S
D1000 Series Serial Converters
D1000 series serial converters.
Description
Ue
(V DC min - max)
The D1061S is used to separate Intrinsically Safe RS 422 / RS 485 equipment
located in Hazardous Location from a RS 422 / RS 485 / RS 232 controller
located in Safe Area.
20 - 30
Item Type
I
Catalogue No.
D1061S
D1061S
Signal Converter and Trip Amplifier
Channels
Hazardous Area
(signal)
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
1
Current:
Single-Ended,
Isolated
CO Relay,
Isolated
-
10 - 30
SIL 2
Item Type
I
Catalogue No.
D1054S
D1054S
D1000 Series Accessories
D1000 Series accessories and replacement parts.
Description
Cold JuNCtion Compensator For THCS Inputs
D1000 Kit For Bus Mounting 1 Required For EACh Section
PC Adapter For D1000 Programmable Units
Pocket Portable Configurator For GMI D1000 Series
Item Type
I
I
I
I
Catalogue No.
OPT1091
OPT1096
PPC1092
PPC1090
55
4
D5000 Series
The GM International D5000 series intrinsically safe isolators have a wide range of functions, suitable for multiple applications from
analogue in and out, digital in and out, temperature converters and trip converters and encoders. With more than 25 modules suitable
for SIL 3 applications according to IEC 61508, IEC 61511.
Each module features an independent power supply circuit for each channel, meaning dual channel units are equivalent to two single
units because of the absence of common circuitry.
Analogue Input
D5000 series analogue input isolators.
Channels
30
D5014S
2
4
Hazardous
Area
(signal)
Current:
Single-Ended,
Isolated
Current:
Single-Ended,
Isolated
Current:
Single-Ended,
Isolated
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
30 - 30
30 - 30
SIL 3
D5014S
-
18 - 30
SIL 3
D5014D
-
20 - 30
SIL 2
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
Current:
Single-Ended,
Isolated
-
18 - 30
SIL 2
Safe Area
(signal)
Current:
Single-Ended,
Isolated
Current:
Single-Ended,
Isolated
Current:
Single-Ended,
Isolated
Item Type
Catalogue No.
D5212Q
I
Analogue Outputs
D5000 series analogue output isolators.
Channels
2
Hazardous
Area
(signal)
Current:
Single-Ended,
Isolated
Item Type
Catalogue No.
D5020D
I
D5020D
Digital Inputs
D5000 series digital input isolators.
Channels
D5030S
1
2
8
Hazardous
Area
(signal)
Voltage Free
Input
Proximity
Switch
Voltage Free
Input
Proximity
Switch
Voltage Free
Input
Proximity
Switch
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
CO Relay,
Isolated
-
18 - 30
SIL 3
D5030S
CO Relay,
Isolated
-
18 - 30
SIL 3
D5030D
Open-Collector
-
18 - 30
SIL 2
D5231E
Item Type
Catalogue No.
Digital Output Drivers
D5000 series digital output drivers.
Channels
1
3
D5049S
56
Hazardous Area
(signal)
Safe Area
(signal)
Ue
(V AC min - max)
Ue
(V DC min - max)
Safety Integrity
Level
(SIL / SIL CL)
CO Relay (I and V
Limited)
CO Relay (I and V
Limited)
Voltage Free
Input
Voltage Free
Input
-
20 - 30
SIL 3
D5049S
-
21.5 - 30
SIL 2
D5240T
Item Type
Catalogue No.
4
Temperature and Trip Converters
D5000 series temperature and trip converters.
Channels
1
2
Ue
(V AC min - max)
-
Ue
(V DC min - max)
18 - 30
18 - 30
Safety Integrity Level
(SIL / SIL CL)
SIL 3
SIL 2
Item Type
I
Catalogue No.
D5072S087
D5072D
D5072S087
D5000 Series Accessories
D5000 Series accessories and replacement parts.
Description
D5000 22mm Bus Connector-1 Required For EACh Module
D5000 12mm Bus Connector-1 Required For EACh Module
D5000 Kit For Bus Mounting-1 Required For EACh Section
PC Adapter For D5000 Programmable Units
Item Type
I
I
Catalogue No.
JDFT050
JDFT049
OPT5096
PPC5092
JDFT050
Hazardous Area Intrinsically Safe Distributed I/O
The new intrinsically safe distributed I/O by Rockwell Automation is a distributed I/O platform that and integrates devices in Hazardous Areas
options via EtherNet/IP. Tight integration with integrated architecture allows easy configuration and a compact, chassis-based I/O design
provides maximum efficiency in a small space.
Today’s development shows that many chemical and petrochemical companies have production plants, production and process automation
machines in operation, which use gas-air or dust-air mixtures which can be explosive. For this reason, the electrical components used in such
plants and systems must not pose a risk of explosion resulting in injury to persons or damage to property.
NHP offer I/O solutions in both hazardous and non-hazardous environments.
When used in hazardous areas of Zone 1 or 2, the NHP I/O solutions offer a safe, easy an economical connection to the sensors and actuators of
Zones 0 and 1.
57
5
Switching and Field Devices
Selection Chart
60
Hazardous Area Plugs and Sockets
Plugs and Sockets
63
Hazardous Area Isolators
Rotary Switches
64
Hazardous Area Field Switches and Sensors
Steute Limit Switches and Sensors
65
Hazardous Area Pull-Wire Switches
Austrol Switches
72
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
58
SAFETY SENSORS
PLUGS AND SOCKETS
ROTARY SWITCHES
LIMIT SWITCHES
FOOT SWITCHES
59
5
Field Switching and Sensing
Selection Chart
Description
Plugs and Sockets
Protection
Technique
Zone 0
Zone 1
Zone 2
Ex d
Ex tb
3
3
Ex d
3
Zone 20
Zone 21
Zone 22
Group
3
3
IIC
Cortem PY /SPY
• 16A and 32A
• 3, 4, 5 pole options
• Aluminium housing,
IIIC
Isolators / Switches
Cortem CSC / EFSCO
• 16, 25 and 63A
• 1, 2, 3 and 4 pole options
• 20V to 415V AC
• Aluminium housing
3
3
3
Ex tb
IIC
IIIC
Limit switches
Steute Ex 14, Ex 335 and Ex T 356
• Thermoplastic, aluminium or zinc die cast Ex d
bodies
Ex tb
• 12 different actuator options
• IP65/ 66/ 67 rating
• SIL rated safety versions
3
3
3
3
IIC
IIIC
Solenoid Interlock Switches
Steute Ex AZM 415 and Ex STM 295
• Thermoplastic or aluminium bodies
• SIL rated safety versions
Ex de
Ex tb
3
Ex de
Ex tb
3
Ex d
Ex tD
3
3
3
3
IIC
IIIC
Belt Drift Switches
Steute Ex 335 4VSR and Ex ZS 73 SR
• Metal or aluminium bodies
• Standard and heavy duty versions
3
3
3
IIC
IIIC
Foot Switches
Steute Ex GFS Series
• With or without protective shield
• Metal enclosure
• IP65
60
3
3
3
IIC
IIIC
5
Description
Tounge Interlock Safety Switches
Protection
Technique
Zone 0
Zone 1
Zone 2
3
3
Zone 20
Zone 21
Zone 22
Group
3
3
IIC
Steute Ex 335 AZ
• Zinc die cast bodies
• Separate actuator
• IP67
Ex de
Ex tb
IIIC
Non-Contact Safety Sensors
Steute Ex HS Si 4 and Ex RC Si
• Rectangular bodies or M30 barrel type
Ex mb
• Thermoplastic or nickel plated brass bodies
• Non-contact coded actuator
3
3
3
3
IIC
IIIC
Emergency Pull-wire Switches
Steute Ex ZS 71 and Ex ZS 80
• Aluminium die cast bodies
• Multiple configurations
• IP65/67
Ex d
Ex tb
3
3
3
3
IIC
IIIC
Inductive sensors
Steute EEx iS
• Stainless steel cyclindrical bodies
• Flush or non-flush mounting
• IP66/67/68
Ex i
3
3
3
3
3
3
IIC
IIIC
Magnetic sensors
EEx RC M20 Series
• Nickel plated brass or stainless steel
cyclindrical bodies
• Up to 30mm sensing distance
• IP67
Ex mb
Ex tb
3
3
3
3
IIC
IIIC
61
Receiver with 4 separate relay
outputs, connected to an external antenna
Up to 4 different switches
can be connected to the
same receiver
Rated distance of up to 450m
Typical nominal transmission distance for indoor
applications = 40-60m
Planning on going wireless?
Explore new possibilities with NHP!
NHP are proud to be able
to provide a reliable suite of
wireless switches and sensors
that allow design flexibility and
lower cost for installations that
require long cable runs.
Our extensive range of wireless switches
and sensors include pushbuttons,
footswitches, limit switches, miniature
remotes and inductive sensors. All
products available are suitable for industrial
automation and the building services
industry. In addition, there are IECEx
certified versions available which are
suitable for Hazardous Area applications.
With the option of either battery-powered
or battery-less operation, battery-less
versions are able to generate their own
power through the energy generated by
clicking the switch, this is also known as
“Electrodynamic Energy Generation”.
NHP ELECTRICAL ENGINEERING PRODUCTS
1300 NHP NHP | nhp.com.au |
Specialised “Universal Transmitter” devices
can be connected to any standard
industrial device with a relay output,
creating a solution where the outputs can
be switched wirelessly.
NHP are proud to bring these to the local
market – customising solutions to suit
varied application requirements. If you’re
looking for a range of wireless switches
and sensors that offer high reliability and
robustness, look no further than NHP.
5
Hazardous Area Plugs and Sockets
Plugs and Sockets
Zones 1, 2 and 21, 22
IECEx CES 11.0011X
Ex d IIC T5
Ex tD A21
IP 66
PY Series
The PY series of socket outlets are rated up to 32A, 690V AC with either 3, 4 or 5 pin configuration. The socket has an integral switch in
the base and is enclosed in a flameproof enclosure
•An interlocked disconnecting switch included with PY series socket
•Rated voltage indentification by ring colour
•Sockets are supplied with reducers/adaptor for cable entries
•These sockets, even if supplied with the plugs SPY are conceived so as not to allow the coupling with standard industrial type plugs
•Body and cover in low copper content aluminium alloy
•PVC blinding plug with chain to prevent from loosing it
PY Socket Kit with Cable Entry
Ie
(A max)
16
16
16
32
32
32
32
Poles
2P + E
2P + E
3P + E
3P + E
3P + E
3P + E
3P + N + E
Ue
(V min - max)
200 - 250
200 - 250
380 - 415
380 - 415
380 - 415
380 - 415
380 - 415
Cable Entries
2 x M20
2 x M25
2 x M25
2 x M25
2 x M32
2 x M25
2 x M32
Weight
(kg)
1.7
1.7
1.7
2.1
2.1
2.1
2.1
Item Type
K
K
K
K
K
K
K
Catalogue No.
PY216BM20
PY216BM25
PY316RM25
PY332RM25
PY332RM32
PY432RM25
PY432RM32
PY216BM20
SPY Series
The PY series of socket outlets and SPY series of plugs are rated up to 32A, 690V AC with either 3, 4 or 5 pin configuration. The socket
has an integral switch in the base and is enclosed in a flameproof enclosure. The integral switch is operated by inserting the plug into
the socket and rotating the plug to the ON position of switch. The plug may not be disengaged while the switch is activated (ON
position) due to a locking lug arrangement.
•Explosion-proof plugs suitable for PY series sockets
•Because of special design, they can be used with industrial sockets
•Body in low copper content aluminium alloy
•Stainless steel screws
•Nickel-plated brass pins
•Ral 7035 epoxy coating.
SPY Plug Kit with Cable Entry
Ie
(A max)
16
16
16
32
32
32
32
Poles
2P + E
2P + E
3P + E
3P + E
3P + E
3P + N + E
3P + N + E
Ue
(V min - max)
200 - 250
200 - 250
380 - 415
380 - 415
380 - 415
380 - 415
380 - 415
Cable Entries
1 x M20
1 x M25
1 x M25
1 x M25
1 x M32
1 x M25
1 x M32
Weight
(kg)
0.3
0.3
0.3
0.6
0.6
0.6
0.6
Item Type
Catalogue No.
K
K
K
K
K
K
K
SPY216BM20
SPY216BM25
SPY316RM25
SPY332RM25
SPY332RM32
SPY432RM25
SPY432RM32
SPY216BM20
63
5
Hazardous Area Isolators
Rotary Switches
Zones 1, 2 and 21, 22
IECEx TSA 06.0009
Ex d IIC T6
Ex tD A21
IP66
CSC Series - 16A
The CSC Series Isolators are single body enclosures and are intended for flameproof (Ex d) and dust ignition proof (Ex tD) applications.
The CSC series enclosures are fitted with a single rotary switch operator located in the cover and have the ability to fit a lock out de
vice (LOTO).
•CSC series isolators, switches and changeover switches are rotary type 16A models with control handle on the cover
•Supplied with adaptors for metric entries
•Body and cover low copper content aluminium alloy
•Frontal aluminium handle, cover fitted with stainless steel closing screws
•Fixing lugs, Internal/external stainless steel earth screws
• Comes with standard padlockable hole
CSC216M20
Operator
(type)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
In
(A)
Poles
Cable Entry
(Top / Bottom)
Weight
(kg)
16
2
M20 / M20
0.95
K
CSC216M20
16
2
M25 / M25
0.95
K
CSC216M25
16
4
M20 / M20
0.85
K
CSC416M20
16
4
M25 / M25
0.85
K
CSC416M25
Item Type
Catalogue No.
EFSCO Series - 25/63A
The EFSCO Series Isolators are single body enclosures and are intended for flameproof (Ex d) and dust ignition proof (Ex tD) applications.
The EFSCO series enclosures are fitted with a single rotary switch operator, with option from 25A to 63A and all isolators have the ability to
fit a lock out device (LOTO).
•The EFSCO series isolators, switches and changeover switches are rotary type 25A, 50A and 63A models with control handle on the cover
•The construction materials are suitable for chemically aggressive environments, also for offshore
•Supplied with adaptors for metric entries
•Body and cover in low copper content aluminium alloy
•Frontal aluminium handle
•Cover fitted with stainless steel closing screw
• Comes with standard padlockable hole
EFSCO24M20
64
Operator
(type)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Off/On Switch
(Isolator)
Changeover Switch
without Off
Changeover Switch
without Off
Changeover Switch
without Off
Changeover Switch
with Off
Changeover Switch
with Off
In
(A)
Poles
Cable Entry
(Top / Bottom)
Weight
(kg)
25
4
M20 / M20
25
4
25
Item Type
Catalogue No.
1.18
K
EFSCO24M20
M25 / M25
1.18
K
EFSCO24M25
4
M32 / M32
1.18
K
EFSCO24M32
63
3
M25 / M25
1.4
K
EFSCO63M25
63
3
M32 / M32
1.4
K
EFSCO63M32
25
2
M20 / M20
1.18
K
EFSCO266M20
25
2
M25 / M25
1.18
K
EFSCO266M25
63
1
M25 / M25
1.4
K
EFSCO66M25
25
2
M20 / M20
1.2
K
EFSCO244M20
25
2
M25 / M25
1.2
K
EFSCO244M25
5
Hazardous Area Field Switches and Sensors
Steute Limit Switches and Sensors
Ex Limit Switches
Ex 14 series
•Ex Zone 1, 2, 21 and 22
•Thermoplastic enclosure
•Double insulated
•Slow action, change-over contact or 2 N/C contacts with double break
•Suitable for in-line mounting
•With pre-wired cable
•Gold-plated contacts available on request
•With latching element (On-/Off principle) available on request
Actuator
Contacts
Connection
Housing
(material)
Top push
plunger
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Built-in cable with
flying leads, 2m
GRP (Glass Reinforced
Plastic / Polyester /
Thermoplastic)
I
EEX14F101S2M
Top push
plunger
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Built-in cable with
flying leads, 2m
GRP (Glass Reinforced
Plastic / Polyester /
Thermoplastic)
I
EEx 14 1O/1S 1m
Wobble stick /
spring rod
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Built-in cable with
flying leads, 2m
GRP (Glass Reinforced
Plastic / Polyester /
Thermoplastic)
I
EEx 14 TK 1O/1S 1m
Item Type
Catalogue No.
EEX14F101S2M
Ex 335 Series
•Ex Zone 1, 2, 21 and 22
•Metal enclosure
•Available with contact overlapping
•Actuator can be repositioned by 4 x 90°
•Rocking lever can be repositioned by 10° steps
•With gold-plated contacts available on request
Actuator
Non-adjustable
roller lever
Adjustable rocker
lever
Contacts
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
Connection
Housing
(material)
Screw Terminal(s)
Enamelled Zinc, Die-Cast
Screw Terminal(s)
Enamelled Zinc, Die-Cast
EEX3354V7H1O1S
EEX335R1O1S
Item Type
I
Catalogue No.
EEx 335 1K 1O/1S
Top push roller
plunger
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
Screw Terminal(s)
Enamelled Zinc, Die-Cast
Non-adjustable
rocker lever
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
Screw Terminal(s)
Enamelled Zinc, Die-Cast
I
EEx 335 4V3H 1O/1S
Top push plunger
2 NC, Slow Action,
Double Break, Positively
Driven
Screw Terminal(s)
Enamelled Zinc, Die-Cast
I
EEx 335 S 2O
Non-adjustable
rod lever
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
Screw Terminal(s)
Enamelled Zinc, Die-Cast
Screw Terminal(s)
Enamelled Zinc, Die-Cast
Screw Terminal(s)
Enamelled Zinc, Die-Cast
Wobble stick /
spring rod
Non-adjustable
rocker lever
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
1 NO + 1 NC, Slow
Action, Double Break,
Positively Driven
EEx 335 1K 1O/1S
EEX3354V10H1O1S
I
EEx 335 TK 1O/1S
EEx 335 4VH 1O/1S
65
5
Ex T 356 Series
Connection is made by means of the integrated connection cable (open-ended line).
•Ex Zone 1, 2, 21 and 22
•Thermoplastic enclosure with metal cover
•Mounting and switching details to EN 50041
•With pre-wired cable
•Actuator can be repositioned by 4 x 90°
•Rocking lever can be repositioned by 10° steps
Actuator
Contacts
Adjustable rocker
lever
Adjustable rocker
lever
Connection
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Built-in cable with
flying leads, 2m
Built-in cable with
flying leads, 5m
Housing
(material)
GRP (Glass Reinforced
Plastic / Polyester /
Thermoplastic)
GRP (Glass Reinforced
Plastic / Polyester /
Thermoplastic)
Item Type
Catalogue No.
EEx T4V7H 356 2m
I
EEx T4V7H 356 5M
EEx T4V7H 356 2m
Ex Solenoid Interlocks
•Aluminium/ steel enclosure
•2 x M20 cable entries
•Two Ex switch inserts in one enclosure
•IP67
Ex AZM 415 Series
•Ex Zone 1, 2, 21 and 22
•Two Ex switch inserts in one enclosure
•Spring-to-lock or power-to-lock principle
•Problem-free opening of stressed doors by means of bell-crank system
•High holding force 3500N
•Ball catch
•Wiring compartment
Actuator
(action)
Fh
(N)
Secondary
Release
(Y / N)
Power to
Lock
3500
No
Power to
Release
3500
No
EEXAZM4152O2SR
66
Contacts
2 NO + 2 NC,
Slow Action,
Double
Break,
Positively
Driven
2 NO + 2 NC,
Slow Action,
Connection
Housing
(material)
Screw
Terminal(s)
Aluminium,
Die-Cast
Screw
Terminal(s)
Aluminium,
Die-Cast
Item Type
I
Catalogue No.
EEx AZM 415 2O/2S A
EEXAZM4152O2SR
5
Ex STM 295 Series
•Ex Zone 1, 2, 21 and 22
•Thermoplastic enclosure
•Double insulated
•Two Ex switch inserts in one enclosure
•Spring-to-lock or power-to-lock principle
•Holding force 1000N
•Wiring compartment
Actuator
(action)
Fh
(N)
Secondary
Release
(Y / N)
Contacts
Connection
Power to
Lock
1000
No
2 NO + 2
NC, Slow
Action,
Screw
Terminal(s)
Power to
Release
1000
No
2 NO + 2
NC, Slow
Action,
Screw
Terminal(s)
Housing
(material)
Item Type
GRP (Glass
Reinforced Plastic
/ Polyester /
Thermoplastic)
GRP (Glass
Reinforced Plastic
/ Polyester /
Thermoplastic)
Catalogue No.
EEx STM 295 2O/2S-A-3
I
EEx STM 295 2O/2S-R-3
EEx STM 295 2O/2S-A-3
Ex Belt Drift Switches
Ex belt alignment switches are suitable for applications with handling equipment. Ex belt alignment switches are actuated when the
conveyor belt becomes misaligned. Depending on the plant arrangements, this signal can either be used to switch the equipment off
or to provide automatic correction of the belt alignment. Thus, they should be installed at both sides of the conveyor belt close to the
deflection and drive pulleys.
Ex 335 4VSR Series Belt Drift Switches
•Ex Zone 1, 2, 21 and 22
•Metal enclosure. Zinc die-cast enamel finish
•2 contacts
•Design to EN 50041
•Wiring compartment
•Adjustable-length rod lever with nylon roller
•For light- and medium-heavy applications
Actuator
Contacts
Housing
(material)
Cable Entry
Adjustable rod
lever
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Enamelled Zinc,
Die-Cast
1 x [M20 x 1.5]
Item Type
Catalogue No.
EEx 335 4VSR 1O/1S
I
EEx 335 4VSR 1O/1S
Ex ZS 73 SR Series
•Ex Zone 1, 2, 21 and 22
•Metal enclosure. Aluminium die-cast enamel finish
•2 contacts
•Cable
•With latching and release by push-button possible
•Belt-alignment roller made of stainless steel 1.4104
Actuator
Contacts
Housing
(material)
Connection
Non-adjustable
roller lever
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Enamelled
Aluminium, Die-Cast
Built-in cable with
flying leads, 3m
Item Type
I
Catalogue No.
EEXZS73SR1O1SVD
EEXZS73SR1O1SVD
67
5
Ex Foot Switches
Ex GFS Series
Ex GFS foot switches are slow action types Zb, 1 N/C plus 1 N/O contact or 2 N/C plus 2 N/O contacts with double break, positive
break N/C contacts. The enclosure is made from aluminium die-cast with an enamel finish in RAL 5011.
•Ex Zone 1, 2, 21 and 22
•1-pedal type
•Metal enclosure
•With protective shield
•Max. 4 contacts
•Low pedal height
•With pre-wired cable, cable length 3m
Guarded
(Y / N)
Contacts
Connection
Housing
(material)
Yes
1 NO + 1 NC, Slow Action,
Double Break, Positively
Driven
Built-in cable with
flying leads, 3m
Aluminium, Die-Cast
Item Type
Catalogue No.
EEx GFS 1O/1S
EEx GFS 1O/1S
Ex Safety Switches
These Ex safety switches with a separate actuator are suitable for sliding, hinged and particularly removable safety guards which
need to be closed to ensure the necessary operational safety. They are also suitable for mounting on profile sections
and retrofitting on existing equipment.
•Suitable for Zone 1, 2, 21 and 22
•Actuation through separate actuator
•Switching element is not physically connected to the actuator
•Thermoplastic, aluminium, zinc die cast or steel bodies
•Solenoid switches available
•IP65/67
Ex 335 AZ Series
The switching element is not physically connected to the actuator but functionally brought together or separated by switching.
When the switch is actuated, the actuator is separated from the base unit. During this process, the N/C contacts of the safety
switch are positively opened and the N/O contacts closed.
•Multiple coding of the actuator
•Slow action, double-break changeover contact
•Metal enclosure
Ex 335 Switches
Contacts
2 NC, Slow Action, Double Break,
Positively Driven
1 NO + 1 NC, Slow Action, Double
Break, Positively Driven
Connection
Housing
(material)
Screw Terminal(s)
Screw Terminal(s)
Item Type
Catalogue No.
Enamelled Zinc, Die-Cast
I
EEx 335 AZ 2O
Enamelled Zinc, Die-Cast
I
EEx 335 AZ 1O/1S
EEx 335 AZ 2O
Ex 335 Actuators
Description
Actuator For The Ex 335 Az Series
Actuator For The Ex 335 Az Series
Actuator For The Ex 335 Az Series
Actuator For The Ex 335 Az Series
68
Item Type
I
I
I
I
Catalogue No.
AZ 335/355-B1
AZ335355B12246
AZ 335/355-B5
AZ 335/355-B6
5
Ex Safety Sensors
Ex HS Si 4 Series
Type Ex HS Si 4 safety sensors are switches intended for the position monitoring of doors, flaps or other safety devices. The activation of
the safety-sensor will be made by coded solenoids. The connection is via a permanently connected cable. The length of the cable is up
to 15m.
•Ex Zone 1, 2, 21 and 22
•Thermoplastic enclosure
•Hall elements, coded
•Actuation from front
•Switching distance up to 8mm
•With pre-wired cable
Ex HS Si 4 Sensors
Indicator
(Y / N)
Contacts
Connection
No
2 NC, Hall effect
Built-in cable with flying
leads, 10m
Housing
(material)
Glass-Filled PA66 /
Thermoplastic (Polyamide 66),
Ultramid A3XZG5
Item Type
Catalogue No.
EEXHSSI42O10M
EEXHSSI42O10M
Ex HS Si 4 Actuators
Description
Item Type
Catalogue No.
EEx MC 4
Ex Magnet Coded For Ex HSSI
EEx MC 4
Ex RC Si M30 Series
The solenoid switch consists of a metal housing into which a thermoplastic housing containing a PCB with four reed contacts,
is mounted and completely potted.
•Ex Zone 1, 2, 21 and 22
•M30 barrel type sensor
•Nickel plated brass and stainless steel bodies available
•24V DC switching
•Pre-wired cable
•Coded reed contacts
•Actuation from front
•Switching distance up to 8mm
•Designed for use in conjunction with a safety relay
Ex RC Si M30 Sensors
Indicator
(Y / N)
Contacts
Connection
Housing
(material)
Yes
Reed, coded
Built-in cable with flying
leads
Stainless Steel
Item Type
Catalogue No.
EEx RC SI M30 6M 2O N
I
EEx RC SI M30 6M 2O N
Ex RC Si M30 Actuators
Description
Coded actuating magnet for the Rc Si M30 Series
Stainless Steel coded actuating magnet for the Rc Si M30 Series
Item Type
I
Catalogue No.
EEXMC30
EEx MC 30 NIRO
EEXMC30
69
5
Ex Emergency Pull-Wire Switches
Ex emergency pull-wire switches are of great importance for the man-machine interface in the area of industrial applications.
They are, for example, applied on transport and conveyor systems. After manual actuation, work and functional processes are initiated
or switched off.
Ex ZS 71 Series
Type Ex ZS 71 pull-wire switches consist of the built-in switch type Ex 14, which is mounted in a light-alloy enclosure with plastic cover
or light-alloy cover of different sizes to protect it against impact. The enclosures are equipped with a pushbutton and connection is
made by means of the integrated connecting cable.
•Ex Zone 1, 2, 21 and 22
•Metal enclosure
•2 contacts
•Small design
•Wire length up to 35m
•Release by push-button (VD)
•Available without unlocking mechanism
•Wire pull and breakage detection
•Watertight collar W for protection against penetration of dirt available
•Position indicator A available
Contacts
EEx ZS 71 1O/1S WVD
1 NO + 1 NC, Slow
Action, Double
Break, Positively
Driven
1 NO + 1 NC, Slow
Action, Double
Break, Positively
Driven
2 NC, Slow Action,
Double Break,
Positively Driven
Cable Max
(m)
Connection
Actuator
(action)
Housing
(material)
35
Built-in cable with flying
leads, 3m
Momentary
Aluminium,
Die-Cast
35
Built-in cable with flying
leads, 3m
Momentary
Aluminium,
Die-Cast
I
EEXZS71101SWVDA
35
Built-in cable with flying
leads, 3m
Momentary
Aluminium,
Die-Cast
I
EEXZS712OWVD
Item Type
Catalogue No.
EEx ZS 71 1O/1S WVD
Ex ZS 80 Series
Type Ex ZS 80 pull-wire switches consist of the built-in switch type Ex 14, which is mounted in a light-alloy enclosure with plastic cover
or light-alloy cover of different sizes to protect it against impact. The enclosures are equipped with a pushbutton and connection is by
means of the integrated connecting cable.
•Ex Zone 1, 2, 21 and 22
•Metal enclosure
•2 contacts
•Position indicator and integrated emergency-stop push-button
•Wire length up to 100m
•Pretensioning force 100N
•Lever for release and position indication
•Watertight collar
•Wire pull and breakage detection
Contacts
1 NO + 1 NC, Slow
Action, Double
Break, Positively
Driven
2 NC, Slow Action,
Double Break,
Positively Driven
EEx ZS 80 1O/1S WVD
70
Cable Max
(m)
Connection
Actuator
(action)
Housing
(material)
100
Built-in cable with flying
leads, 3m
Momentary
Aluminium,
Die-Cast
I
EEx ZS 80 1O/1S WVD
100
Built-in cable with flying
leads, 3m
Momentary
Aluminium,
Die-Cast
I
EEx ZS 80 2O WVD
Item Type
Catalogue No.
5
Ex intrinsically Safe Inductive Sensors
Zones 0,1 2 and 20, 21, 22
IECEx IMQ 14.0001X
Ex ia IIC T6 Ga
Ex ia IIIC T85°C Da
IP68
Features:
•
•
•
•
•
•
•
Stainless steel enclosure
Flush or non-flush mounting
LED indicator
Pre-wired 2m cable
8.2 V DC 2 wire Namur switching
Suitable for the food processing industry
Designed to be used with intrinsically safe isolators
EEx IS M8 B
Mounting
Sensing Distance
(mm min-max (nom))
Connection
Housing
(material)
Thread
(size)
Flush Mount
Non-Flush Mount
Flush Mount
Non-Flush Mount
Flush Mount
Non-Flush Mount
-
, 2m
, 2m
, 2m
, 2m
, 2m
, 2m
Stainless Steel, 303
Stainless Steel, 303
Stainless Steel, 303
Stainless Steel, 303
Stainless Steel, 303
Stainless Steel, 303
M12 x 1
M12 x 1
M18 x 1
M18 x 1
M30 x 1.5
M30 x 1.5
(2)
(4)
(5)
(8)
(10)
(15)
Flush mounting
Item Type
I
I
I
I
Catalogue No.
EEXISM12B2ABBAB
EEXISM12NB4ABBAB
EEXISM18B5ABBAB
EEXISM18NB8ABBAB
EEXISM30B10ABBAB
EEXISM30NB15ABBAB
Non-flush mounting
Ex Magnetic Sensors
The Ex magnetic sensors are actuated by an M range permanent magnet, entering their proximity without any physical contact.
These devices are available with N/O, N/C, changeover, bistable or bistable changeover contacts. All magnetic sensors are supplied
with pre-wired cables. When using Ex magnetic sensors, care must be taken that their mounting site is free of magnetic fields.
•Ex Zone 1, 2, 21 and 22
•Nickel-plated brass enclosure
•Available in stainless steel Including 2 mounting nuts 1reed contact
•Actuation from front, actuation from side only with bistable contact
•Switching distance up to 30mm depending on the actuating magnet
•With pre-wired cable
•Version for low temperatures up to -40 °C
•With lapptherm 145 cable available on request
RCM20 Series
Actuation
(direction)
Contacts
Connection
Housing
(material)
Front
1 CO, Reed
Built-in cable with flying
leads, 2m
Nickel-Plated Brass
Item Type
Catalogue No.
I
EEXRCM201W
EEXRCM201W
71
5
Ex-Rated Safety Pull-Wire Switches
Zones 21, 22
ANZEx 05.4008X
Ex tD A21 T85oC
IP65/67
•Dust excluding ignition proof trip-wire switch suited for hazardous area applications
Standard Switches
Contacts
(safety)
2 NO + 2 NC
Housing
(material)
Aluminium,
Die-Cast
E-Stop Btn
(Y / N)
IP Rating
Cable Entry
(position)
No
IP65, IP67
Left and Right
E-Stop Btn
(Y / N)
IP Rating
Cable Entry
(position)
No
IP65, IP67
Left and Right
Item
LDC
Type
NR6101D
Catalogue No.
EX55.4.00NBB
EX55.4.00NBB
Switches with Glass Windows
Contacts
(safety)
2 NO + 2 NC
Housing
(material)
Aluminium,
Die-Cast
Item
LDC
Type
NR6101D
Catalogue No.
EX55.4.00GWNBB
EX55.4.00GWNBB
Lanyard Rope/Pull-wire
Developed to meet the Australian and New Zealand safety standards, these ropes are specially tested to work in conjunction with the
NHP/Austrol NTW series pull-wire switches. Two types are available; PVC covered galvanised trip-wire and NHP tufflex fibre lanyard rope.
Individual maximum lengths of lanyard must not exceed 100m when using NHP tufflex rope or 60m when using PVC coated galvanised
trip wire.
Installation Kits
Trip-wire install kits are complete kits which include a length of wire as well as the required fixing hardware. These are available for both
single-sided and double-sided switches in both types of trip-wire.
PVC Coated Galvanised Steel Pull-Wire Installation Kits
Description
Trip Wire Install Kit 7mm PVC Coated Steel Wire 40m
72
Item
LDC
Type
K
NR6101D
Catalogue No.
PVCWIREKIT40M
5
Lanyard
NHP tufflex is a high-performance multi-filament yarn spun from liquid crystal polymer. It is the only commercially available melt-spun
LCP fibre in the world exhibiting low weight and exceptional strength and rigidity. It is five times stronger than steel and ten times
stronger than aluminium.
NHP Tufflex Pull-wire
Description
NHP/Tufflex, Liquid Crystal Polymer fibre rope, (per metre)
NHP/Tufflex, Liquid Crystal Polymer fibre rope, 105m roll
Item
LDC
Type
NR6101D
NR6101D
Catalogue No.
55.1.53RLRPM
55.1.53RLR
55.1.53RLRPM
PVC Coated Galvanised Steel Lanyard
Description
Trip Wire, 5mm, Galvanised Steel, Red PVC Coated
Trip Wire, 7mm Galvanised Steel Red PVC Coated (per metre), suitalbe for pull-wire switches
Item
LDC
Type
NR6101D
NR6101D
Catalogue No.
55.1.33P
55.1.53P
55.1.33P
Accessories
Lanyard Installation Accessories
Description
U” bolt 5mm wire clamp/shackle, suitable for pull-wire switches
5mm wire thimble, suitable for pull-wire switches
5mm stainless steel wire clamp/shackle, suitable for pull-wire switches
D Shackle 6mm, for pull-wire switches
5mm Stainless steel wire thimble, suitable for pull-wire switches
Wire support bracket, 5mm for NTW switch
Hook and eye turnbuckle 10mm, for pull-wire switches
Stainless steel D shackle, for pull-wire switches
Wire support bracket, 6mm stainless steel for NTW switch
Hook and eye turnbuckle 10mm Stainless Steel, for pull-wire switches
Trip wire switch tension spring, for pull-wire switches
Stainless Sseel trip wire switch tension spring, for NTW switch
Trip wire switch tension spring stainless steel, for pull-wire switches
Item
LDC
Type
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
NR6101D
Catalogue No.
55.1.52
55.1.51
55.1.52SS
55.2.18
55.1.51SS
55.1.50
55.1.64
55.2.19
55.1.50SS
55.1.64SS
55.2.46
55.1.46SS
55.2.46SS
55.1.52
Spare Parts
Description
Shaft bellow for pull-wire switches
Item
LDC
Type
NR6101D
Catalogue No.
55.2.37
73
6
Ex Signalling
Selection Chart
76
Hazardous Area Beacons
Moflash Beacons
Intrinsic Safe Beacons
77
77
Hazardous Area Sounders
Moflash Sounders
Intrinsic Safe Sounders
Sounder / Beacons 80
80
81
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
74
XENON BEACON
MANUAL CALL POINT
SOUNDER
COMBINATION
UNITS
75
6
Signalling Devices
Selection Chart
Description
Signalling Beacons
Protection
Technique
Zone 0
Zone 1
Zone 2
3
3
3
3
3
3
3
3
3
3
Zone 20
Zone 21
Zone 22
Group
3
3
IIC
IIIC
3
3
IIC
IIIC
3
3
IIC
IIIC
3
3
IIC
IIIC
3
3
IIC
IIIC
Moflash BC150 and BC125 Beacons
• LED or xenon light source
• GRP or stainless steel bodies
• Various lens and body colours
• Wide range of operating voltages
Ex d
Ex tb
Signalling Beacons
Moflash Ex I Beacons
• LED light source
• GRP bodies
• Various lens colours
Ex i
3
3
Sounders
Moflash SD150 and SD125
• GRP or stainless steel bodies
• Sound output 115dB @ 1 metre
Ex d
Ex tb
Sounders
Moflash Ex I Sounders
• GRP body
• Sound output 100dB @ 1 metre
Ex i
3
3
Sounder / Beacons
Moflash SB150 and SB125
• GRP or stainless steel bodies
• Sound output 115dB @ 1 metre
• Various lens and body colours
• Wide range of operating voltages
76
Ex de
Ex tb
6
Hazardous Area Sight
Moflash Sight
Zones 1, 2 and 21, 22
IECEx NEM 13.0030X
Ex d IIC T4/5/6
Ex tb IIIC T85/100/135 ºC
IP66
Ambient temperature
–40ºC + 55 / 60 / 70ºC
Features and Benefits
•Xenon strobe or LED light source
•LED selectable rotating, flashing or steady-on
•GRP or stainless steel construction
•Suitable for on-shore and off-shore applications
•Cable entry 4 x M20
•Stainless steel lens guard (optional)
•Available in different lens colour and enclosure colour
•More options available including status light and sounder combinations, contact NHP for more information
BC150 Series GRP Beacon
These GRP beacons have a choice of two types of light source; either Xenon (strobe) with multiple flash rate and power ratings or an LED
array with three status type indication (steady, flashing, rotate) options and two power ratings.
LED Series
The LED lighting series can be operated by both AC and DC voltage and are available with a wide range of lens colours.
DIP switches can be changed to alter flash rate, rotation rate or steady on mode.
•Enclosure: GRP
•Available in different lens color and enclosure color
•Power supply 12-48V DC, 12-48V AC or 100-240V AC
•Cable entry 4 x M20, M25, 1/2”NPT, 3/4”NPT
•Length/Width: 150mm / 5.91” Height: 212mm / 8.35”
AC Voltage Operated
Lamp
(type)
Lamp
(W max)
Lens
(colour)
LED
10
Amber
LED
10
Green
LED
10
Red
Illumination
(mode)
Steady / Flashing /
Rotating
Steady / Flashing /
Rotating
Steady / Flashing /
Rotating
Ue
(V AC min-max)
Illumination
(mode)
Steady / Flashing /
Rotating
Steady / Flashing /
Rotating
Steady / Flashing /
Rotating
Steady / Flashing /
Rotating
Ue
(V DC min-max)
100 - 240
100 - 240
100 - 240
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
I
BC150AL10ACNNNARDN
I
BC150GL10ACNNNARDN
I
BC150RL10ACNNNARDN
BC150GL10ACNNNARDN
DC Voltage Operated
Lamp
(type)
Lamp
(W max)
Lens
(colour)
LED
10
Amber
LED
10
Blue
LED
10
Green
LED
10
Red
12 - 48
12 - 48
12 - 48
12 - 48
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
BC150AL10DCNNNARDN
I
BC150BL10DCNNNARDN
I
BC150GL10DCNNNARDN
BC150RL10DCNNNARDN
BC150AL10DCNNNARDN
77
6
Xenon Lighting Series
The xenon lighting series can be operated by both AC and DC voltage and is available with a wide range of lens colours.
•Enclosure: GRP
•Available in different lens color and enclosure color
•Power supply 12-48V DC, 12-48V AC or 100-240V AC
•Cable entry 4 x M20, M25, 1/2”NPT, 3/4”NPT
•Length/Width: 150mm/5.91” Height: 212mm/8.35”
AC Voltage Operated
BC150AX20ACNNNARDN
Lamp
(type)
Lamp
(W max)
Lens
(colour)
Illumination
(mode)
Ue
(V AC min-max)
Xenon
25
Amber
Flashing
100 - 240
Xenon
25
Blue
Flashing
100 - 240
Xenon
25
Green
Flashing
100 - 240
Xenon
25
Red
Flashing
100 - 240
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
I
Catalogue No.
BC150AX20ACNNNARDN
BC150BX20ACNNNARDN
I
BC150GX20ACNNNARDN
BC150RX20ACNNNARDN
DC Voltage Operated
BC150GX20DCNNNARDN
Lamp
(type)
Lamp
(W max)
Lens
(colour)
Illumination
(mode)
Ue
(V DC min-max)
Xenon
25
Blue
Flashing
12 - 48
Xenon
25
Green
Flashing
12 - 48
Xenon
25
Amber
Flashing
12 - 48
Xenon
25
Red
Flashing
12 - 48
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
I
BC150BX20DCNNNARDN
I
BC150GX20DCNNNARDN
BC150AX20DCNNNARDN
I
BC150RX20DCNNNARDN
BC125 Series SS Beacon
These stainless steel beacons have a choice of two types of light source: either xenon (strobe) with multiple flash rate and power ratings
or an LED array with three status type indication (steady, flashing, rotate) options and two power ratings.
•Enclosure is made from stainless steel 316 and lens are made from tempered glass
•Two types of light source; either xenon or LED
•The design allows for termination inside the enclosure
•360 degree light output around the vertical axis
•Dustproof and weatherproof
Xenon Lighting Series
The Xenon lighting series can be operated by both AC and DC voltage and is available with a wide range of lens colours.
•Enclosure: stainless steel 316 and lens: tempered glass
•Available in different lens color and enclosure color
•Power supply 12-48V DC, 12-48V AC or 100-240V AC
•Cable entry 4 x M20, M25, 1/2”NPT, 3/4”NPT
•Length/width: 125mm/4.92” Height: 181.2mm/7.13”
AC Voltage Operated
BC125AX20ACNNNARDN
78
Lamp
(type)
Lamp
(W max)
Lens
(colour)
Illumination
(mode)
Ue
(V AC min-max)
Xenon
25
Amber
Flashing
100 - 240
Xenon
25
Blue
Flashing
100 - 240
Xenon
25
Green
Flashing
100 - 240
Xenon
25
Red
Flashing
100 - 240
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
I
BC125AX20ACNNNARDN
I
BC125BX20ACNNNARDN
I
BC125GX20ACNNNARDN
I
BC125RX20ACNNNARDN
6
DC Voltage Operated
Lamp
(type)
Lamp
(W max)
Lens
(colour)
Illumination
(mode)
Ue
(V DC min-max)
Xenon
25
Blue
Flashing
12 - 48
Xenon
25
Green
Flashing
12 - 48
Xenon
25
Red
Flashing
12 - 48
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
I
BC125BX20DCNNNARDN
I
BC125GX20DCNNNARDN
I
BC125RX20DCNNNARDN
BC125BX20DCNNNARDN
Accessories
Description
Lens guard stainless steel for BC/SB Range
Item Type
I
Catalogue No.
MO50023
Ex i Beacons
Description
Item Type
Ex i Beacon 15-28V DC Amber
Catalogue No.
EAE1500601
Status Lights and Sounder Combination Units
Zones 1, 2 and 21, 22
IECEx NEM 13.0035X
IECEx NEM 13.0036X (sounder / beacon)
Ex d IIC T4/T5/T6
Ex tb IIIC T85°C/T100°C/T135°C
IP 66
Ambient temperature:
- 40º C + 70º C
Features:
Status lights and signalling units are built to order, in both GRP and stainless steel.
Combinations of beacons for status lights are available in xenon or LED technologies, and various voltages.
Electronic sounders , pushbuttons and junction boxes can also be incorporated into the design, including internal wiring to a
junction box to save on installation time.
Please contact NHP for a quote today
79
6
Hazardous Area Sound
Moflash Sound
Zones 1, 2 and 21, 22
IECEx NEM 13.0032X (Sounder)
IECEx NEM 13.0036X (Sounder / Beacon)
Ex d IIC T4/T5/T6
Ex tb IIIC T85°C/T100°C/T135°C
IP66
Ambient temperature:
40º C + 70º C
Features and Benefits
•Sound output , 115 dB @ 1 metre
•3 stage alarm 63 selectable tones
•Maximum current draw 1.5 amps
•GRP or stainless steel construction
•Suitable for on-shore and off-shore applications
•Cable entry 2 x M20
•Available in different lens color and enclosure color
•More options available including status light and sounder combinations, contact NHP for more information
SD150 Series GRP Sounder
Sound Lvl
(dB @1m)
115
115
Ue
(V AC min-max)
100 - 240
12 - 48
Housing
(colour)
RAL 3001, Signal Red
RAL 3001, Signal Red
Item Type
I
Catalogue No.
SD1501ACNNARD
SD1501DCNNARD
SD1501ACNNARD
SD125 Series SS Sounder
Sound Lvl
(dB @1m)
115
115
Ue
(V AC min-max)
100 - 240
12 - 48
Housing
(colour)
RAL 3001, Signal Red
RAL 3001, Signal Red
Item Type
I
I
Catalogue No.
SD1251ACNNARD
SD1251DCNNARD
SD1251ACNNARD
EA150 Series Intrinsically Safe Sounder
Zones 0, 1, 2 and 20, 21, 22
Designed to be used with intrinsically safe isolators, please contact NHP for further information.
Sound Lvl
(dB @1m)
100
80
Ue
(V DC min-max)
- 24
Item Type
Catalogue No.
EA15006
6
SB150-1 Series GRP Sounder/Beacon
AC Voltage Operated
The Xenon lighting series can be operated by both AC and DC voltage and is available in different lens colours.
•Enclosure: stainless steel 316 and lens: tempered glass
•Available in different lens color and enclosure color
•Power supply 12-48V DC, 12-48V AC or 100-240V AC
•Cable entry 4 x M20, M25, 1/2”NPT, 3/4”NPT
•Length/width: 413mm /16.4”
SB1501RX15ACNNNARDN
AC
Lamp
(type, power)
Xenon, 20W max
Xenon, 20W max
Lens
(colour)
Amber
Red
Sound Lvl
(dB @1m)
115
115
Ue
(V AC min-max)
100 - 240
100 - 240
Housing
(colour)
RAL 3001, Signal Red
RAL 3001, Signal Red
Item Type Catalogue No.
SB1501AX15ACNNNARDN
SB1501RX15ACNNNARDN
I
I
SB1501RX15DCNNNARDN
DC
Lamp
(type, power)
Xenon, 20W max
Xenon, 20 W max
Lens
(colour)
Amber
Red
Sound Lvl
(dB @1m)
115
115
Ue
(V DC min-max)
12 - 48
12 - 48
Housing
(colour)
RAL 3001, Signal Red
RAL 3001, Signal Red
Item Type
Catalogue No.
SB1501AX15DCNNNARDN
SB1501RX15DCNNNARDN
I
I
SB125-1 Series SS Sounder/Beacon
Xenon Lighting Series
The xenon lighting series can be operated by both AC and DC voltage and is available with a wide range of lens colours.
•Enclosure: stainless steel 316 and lens: tempered glass
•Available in different lens color and enclosure color
•Power supply 12-48V DC, 12-48V AC or 100-240V AC
•Cable entry 4 x M20, M25, 1/2”NPT, 3/4”NPT
•Length/width: 333mm /13.1” SB1251RX15ACNNNARDN
AC
Lamp
(type, power)
Lens
(colour)
Illumination
(mode)
Sound Lvl
(dB @1m)
Ue
(V AC min-max)
Xenon, 20W max
Amber
Flashing
115
100 - 240
Xenon, 20W max
Red
Flashing
115
100 - 240
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type Catalogue No.
I
SB1251AX15ACNNNARDN
I
SB1251RX15ACNNNARDN
SB1251AX15DCNNNARDN
DC
Lamp
(type, power)
Lens
(colour)
Illumination
(mode)
Sound Lvl
(dB @1m)
Ue
(V DC min-max)
Xenon, 20W max
Amber
Flashing
115
12 - 48
Xenon, 20W max
Red
Flashing
115
12 - 48
Housing
(colour)
RAL 3001,
Signal Red
RAL 3001,
Signal Red
Item Type
Catalogue No.
I
SB1251AX15DCNNNARDN
I
SB1251RX15DCNNNARDN
81
7
Cable Glands and Accessories
Selection Chart
84
Hazardous Area Cable Glands
Ex Cable Glands
85
Hazardous Area Adaptors, Reducers and Accessories
Plugs, Adaptors, Reducers and Accessories
88
Item Type (Ordering information)
I Indent item (non refundable)
A Assembled to order (non refundable)
K A kit item which contains a number of parts (may contain indent items)
Blank Stocked
82
TERMINAL AND
JUNCTION BOXES
CABLE GLANDS FOR
ARMOURED CABLES
ADAPTORS AND
REDUCERS
CABLE GLANDS FOR
NON-ARMOURED
CABLES
83
7
Cable glands and Accessories
Selection chart
Protection
Description
Technique
Glands for Non-Armoured Cables
Cortem REV
• Nickle plated brass
Ex d
• Stainless steel
Ex e
• IP66/67
Ex tb
Zone 1
Zone 2
Zone 21
Zone 22
Group
3
3
3
3
IIC
IIIC
3
3
3
3
IIC
IIIC
3
3
3
3
I/II
Ex d, Ex e, Ex nR, Ex tD
3
3
3
3
I/II
Ex d
Ex e
Ex tD
3
3
3
3
IIC
IIIC
Ex d
Ex e
Ex tD
3
3
3
3
IIC
IIIC
3
3
3
3
IIC
IIIC
Glands for Armoured Cables
Cortem REVD
• Nickle plated brass
• Stainless steel
• IP66/67
Ex d
Ex e
Ex tb
Barrier (resin fill) Armoured Cable Gland
PX2KW
• Armoured (SWA) cables
• Barrier (resin fill) type
cable gland
• Triple certified
• Nickel plated brass
Ex d, Ex e, Ex nR, Ex tD
Barrier (resin fill) Non-Armoured Cable Gland
PXSS2K
• Non Armoured cables
• Barrier (resin fill) type
cable gland
• Triple certified
• Nickel plated brass
Plugs
Cortem PLG
• Adaptors
• Reducers
• Stopping plugs
• Nickle plated brass
• Stainless Steel
• IP66/67
Cortem RE
• Adaptors
• Reducers
• Nickle plated brass
• Stainless Steel
• IP66/67
Locknuts
RE Series
• Nickle plated brass
• Stainless steel
84
7
Hazardous Area Cable Glands
Ex Cable glands
Zone 1,2 and 21,22
IECEx CES 13.0005X
Ex d IIC Gb
Ex e IIC Gb
Ex tb IIIC Db
IP66/67
Ambient temperature:
-40º C + 110º C
Features and Benefits
•Comes with o-ring for IP protection
•Triple certified, Ex d, Ex e and Ex tb
•Nickel plated brass construction
•Stainless steel, polyamide and galvanized steel available upon request
•Female threads available upon request
•Intrinsically safe variants available (cable glands are partially painted light blue)
REV Glands For Non-Armoured Cables
The REV cable glands are suitable for use in Hazardous Areas with non-armoured cables. The REV series cable glands are designed to be
inserted into explosion-proof junction boxes and/or lighting fixtures, plugs and other Hazardous Area equipment. They are provided
with high-tech and high mechanical performance compression rings and gaskets with high-temperature resistance.
Thread
(size)
M16 x 1.5
M20 x 1.5
M20 x 1.5
M25 x 1.5
M25 x 1.5
M32 x 1.5
M32 x 1.5
HxW
(mm)
45 x 28
45 x 28
47 x 28
45 x 37
46.5 x 37
46.5 x 40
53.5 x 47
Cable Diameter
(mm min-max)
5 - 10
5 - 10
7 - 12
7 - 12
12 - 18
12 - 18
18 - 24
Material
Item Type
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
I
I
Catalogue No.
REV01IB
REVL1IB
REV1IB
REVL2IB
REV2IB
REVL3IB
REV3IB
REV1IB
REVD Glands for Armoured Cables
The new REVD series cable glands are suitable for use in Hazardous Areas with danger of explosion to enable direct insertion of
armoured cables into explosion-proof junction boxes, lighting fixtures, plugs and sockets, etc. The most important innovation is the
use of one sealing ring on the inner and outer sheath of the cable compared to the previous kit with various sealing rings which
tightens the incoming cable ensuring the Ex d protection. REVD series has a second sealing ring that tightens on the outer sheath
of the cable to ensure the IP66/67 degree of protection avoiding the ingress of water, moisture, rain and dust.
Thread
(size)
HxW
(mm)
Outer Sheath
Diameter
(mm min-max)
Inner Sheath
Diameter
(mm min-max)
M16 x 1.5
69 x 28
8 - 15
5 - 10
M20 x 1.5
70 x 28
8 - 15
5 - 10
M20 x 1.5
70 x 28
11 - 16
7 - 12
M25 x 1.5
70 x 37
11 - 16
7 - 12
M25 x 1.5
71.5 x 37
16 - 24
12 - 18
M32 x 1.5
80.5 x 47
24 - 31
18 - 24
Material
Nickel-Plated
Brass
Nickel-Plated
Brass
Nickel-Plated
Brass
Nickel-Plated
Brass
Nickel-Plated
Brass
Nickel-Plated
Brass
Item Type
Catalogue No.
REVD1IB
REVD01IB
I
REVDL1IB
REVD1IB
I
REVDL2IB
REVD2IB
REVD3IB
85
7
Barrier cable glands for armoured cables
PX2K series
Zone 1,2 and 21,22
IECEx SIR 06.0044X
Ex d IIC/Ex e II /Ex nR II or Ex d IIC, Ex e II or
Ex tD A21 IP66
Ex d I/Ex e I or Ex d I or Ex e I
Features and Benefits
• Suitable for steel wire armour (SWA) cables
• Barrier (resin fill) type cable gland
• Triple certified Ex d, Ex e, Ex nR
• Nickel plated brass construction
• Stainless steel version available upon request
• Resin subject to expiry date
Thread
(size)
Thread
(size)
Cable gland
size
Min
Thread
length “A
Across
Overall cable
corners“C”
Min
Max
Material
Protrusion
Weight
length “D”
(Kgs)
Item type
Catalogue No.
M20
20S
15
9.5
15.9
33.6
58.5
0.163
PX2K20S16
M20
20
15
12.5
20.9
33.6
60.5
0.217
PX2K20S
M20
20
15
14
22
41.3
67.5
0.345
PX2K20
M25
25
15
18.2
26.2
41.3
67.5
0.345
PX2K25
M32
32
15
23.7
33.9
50.6
69.5
0.484
PX2K32
Other sizes available upon request
86
B
7
Barrier cable glands for non-armoured cables
PXSS2K series
Zone 1,2 and 21,22
IEx d IIC/Ex e II /Ex nR II or Ex d IIC, Ex e II or
Ex tD A21
IP66
Ex d I/Ex e I or Ex d I or Ex e I
Features and Benefits
• Suitable for un-armoured cables
• Barrier (resin fill) type cable gland
• Triple certified Ex d, Ex e, Ex nR
• Nickel plated brass construction
• Stainless steel version available upon request
• Resin subject to expiry date
Thread
(size)
Thread
(size)
Cable gland
size
Min
Thread
length “A
B
Across
Overall cable
corners“C”
Min
Max
Material
Protrusion
Weight
length “D”
(Kgs)
Item type
Catalogue No.
M20
20S
15
3.1
8.7
32.9
58.5
0.200
PXSS2K20S16
M20
20
15
6.1
11.7
32.9
58.5
0.200
PXSS2K20S
M20
20
15
6.5
14.0
32.9
60.5
0.250
PXSS2K20
M25
25
15
11.1
20.0
40.5
67.5
0.403
PXSS2K25
M32
32
15
17.0
26.3
49.6
69.5
0.555
PXSS2K32
Other sizes available upon request
87
7
Hazardous Area Adaptors, Reducers and Accessories
Plugs, Adaptors, Reducers and Accessories
Zone 1, 2 and 21, 22
IECEx CES 10.0001X
Ex d IIC Gb
Ex e IIC Gb
Ex tb IIIC Db
IP66/67
Features and Benefits
•Triple certified, Ex d, Ex e and Ex tb
•Material, size and thread variants available upon request
Plugs
PLG series plugs are used to close the unused entries and are certified for multiple protection techniques. They have a hexagonal
head so that they can only be opened with correct tools.
•With rabbeted hexagon for plugs with tapered thread,
•With external hexagon for plug with cylindrical thread.
PLG1IB
Thread
(size)
M16 x 1.5
M20 x 1.5
M25 x 1.5
M32 x 1.5
0.5” ISO 7-1
0.75” ISO 7-1
1” ISO 7-1
1.25” ISO 7-1
1.5” ISO 7-1
Material
Item Type
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Catalogue No.
PLG01IB
PLG1IB
PLG2IB
PLG3IB
PLG1B
PLG2B
PLG3B
PLG4B
PLG5B
I
I
I
Note: Other sizes and stainless steel available upon request
Adaptors and Reducers
Reducers and adaptors are used to connect equipment, enclosures, pipes and hubs of different diameters and threads. They are certified for multiple protection techniques.
REBIF25GM2B
Thread
(size - male)
1” ISO 7-1
1” ISO 7-1
1.5” ISO 7-1
1.5” ISO 7-1
0.75” ISO 7-1
1” ISO 7-1
0.75” ISO 7-1
Thread
(size - female)
M20 x 1.5
M25 x 1.5
M25 x 1.5
M32 x 1.5
M25 x 1.5
M32 x 1.5
M20 x 1.5
Material
Item Type
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
Nickel-Plated Brass
I
Catalogue No.
REGM3IF20B
REGM3IF25B
REGM5IF25B
REGM5IF32B
REBIF25GM2B
REBIF32GM3B
REGM2IF20B
Other thread types, sizes and materials available upon request
RE Series
Metric (ISO) Thread size
Metric (ISO)
Catalogue No.
M20
M16
REGIF20IM16B
M25
M20
REGIF25IM20B
M32
M20
REGIF32IM20B
M32
M25
REGIF32IM25B
Other sizes available upon request
Gaskets
Description
Silicon Gasket M16
Silicon Gasket M20
Silicon Gasket M25
88
Item Type
Catalogue No.
GRN-16
GRN-20
GRN-25
7
Hazardous Area Adaptors, Reducers and Accessories
Adapters, Reducers and Accessories
Reducers and adaptors are used to connect equipment, enclosures, pipes and hubs of different diameters and threads.
Features and Benefits
•Adaptors and reducers are constructed from nickel plated brass
•Other materials available upon request; stainless steel and galvanised steel
Adapters, Reducers and Accessories
Reducers and adaptors are used to connect equipment, enclosures, pipes and hubs of different diameters and threads.
•Adaptors and reducers are constructed from nickel plated brass
•Other materials available upon request; stainless steel and galvanised steel
LN Series
Brass locknuts are recommended when securing brass cable glands, unions, adaptors, reducers, and stopper plugs to a gland plate or
into equipment. Zinc plated mild steel locknuts are a cost effective alternative to brass locknuts and should only be used in dry, low
humidity conditions.
Thread
(size)
M16 x 1.5
M20 x 1.5
M25 x 1.5
M32 x 1.5
M63 x 1.5
ThreadLen
(mm)
3.2
3.2
3.2
3.2
3.2
Material
Brass
Brass
Brass
Brass
Brass
Item Type
Catalogue No.
LN5-16
LN5-20
LN5-25
LN5-32
LN5-63
LN5-16
89
Industry Recognised Hazardous Area Training from NHP
and Competency Training (CT)
NHP are pleased to announce
that we have entered an
exclusive collaboration
agreement with nationally
recognised training provider,
Competency Training (CT) for
the hosting of Hazardous Area
training classes.
In line with NHP’s commitment to valueadd training and services for our customers,
this agreement will enable the two
companies to jointly service customer
training in Australia and New Zealand.
CT are an Australian registered training
organisation providing professional services
and technical training in areas including
electrical equipment for Hazardous Areas.
CT are also recognised under the IECEx
- Recognized training provider program
allowing them to provide training services
related to the selection, design, inspection,
installation, maintenance, repair, overhaul
and reclamation of equipment operating in
explosive (Ex) atmospheres.
NHP ELECTRICAL ENGINEERING PRODUCTS
1300 NHP NHP | nhp.com.au |
90
The courses that are currently on offer from
NHP and CT include:
• Installation and Maintenance of electrical equipment in Hazardous Areas
• Installation and Maintenance of electrical equipment in Hazardous Areas Refresher
• Hazardous Areas Awareness
• Hazardous Area Awareness Online
• Hazardous areas
• Classification and Design
• Hazardous Areas Classification
• Hazardous Area Compliance
• Certificate IV Hazardous Areas – Electrical
LOW VOLTAGE
MEDIUM VOLTAGE POWER
SWITCHGEAR
TRANSFORMER
POWER DISTRIBUTION
& PROTECTION
DISTRIBUTION
BOARDS
POWER
QUALITY
INFORMATION
SOFTWARE
COMMUNICATION NETWORK
AUTOMATION
SYSTEMS
HMI
EtherNet/IP
MOTOR
CONTROL
CENTRES
HMI
DISTRIBUTED I/O
SIGNALLING DEVICES
PC/SOFTWARE
OPERATOR STATION
SOFT
STARTER
FIELD SWITCHING
& SENSING
PROCESS
CONTROL
SYSTEMS
WIRELESS
SYSTEMS
ENERGY MANAGEMENT
CONTROL SYSTEMS &
BUILDING AUTOMATION
SAFETY
SERVO MOTORS
& GEARBOX
PROCESS
INSTRUMENTATION
MOTOR
CONTROL
CONDITION
MONITORING
MOTION
SYSTEMS
DRIVES
MOTION
HAZARDOUS AREA
EQUIPMENT
INDUSTRIAL CONTROLS
SERVICES & TRAINING
> Operator control devices
> Signalling devices
> Plugs, sockets & switches
> Timers & control relays
> Terminations & wiring systems
> Enclosures & climate controls
> Repairs
> Field services
> Training & support
> Contracts & customer support
> Engineered solutions
We integrate world’s best products
to provide value-add solutions
At NHP, we are more than simply a product supplier. NHP
provide a range of products, services and expertise to help
our customers create electrical and automation solutions that
improve our world. Our local expertise across a range of diverse
industries is backed by the knowledge base of world class
supply line partners.
This enables NHP to customise integrated solutions that focus
on making systems smarter, safer, more secure, reliable and
efficient. From low or medium voltage power distribution
solutions, to process automation, to smarter buildings, NHP is
helping to create a better connected world.
91
AUSTRALIA
NEW ZEALAND
SALES 1300 NHP NHP
SALES 0800 NHP NHP
[email protected]
[email protected]
nhp.com.au
nhp-nz.com
NHP Electrical Engineering Products
For more in
download
offering ex
catalogues
A.B.N. 84 004 304 812
NOEMNONAPRC 4/17
© Copyright NHP 2017
For more information, scan to download
the NHP eCatalogues App offering exclusive
video content, catalogues and literature
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement