Warrior™ Feed 304 Warrior™ Feed 304w

Warrior™ Feed 304 Warrior™ Feed 304w
Warrior™ Feed 304
Warrior™ Feed 304w
Instruction manual
0463 363 001 GB 20130618
Valid for: serial no. 324-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY ................................................................................................................ 4
2
INTRODUCTION ................................................................................................... 7
2.1
Overview ............................................................................................................... 7
2.2
Equipment............................................................................................................. 7
3
TECHNICAL DATA ............................................................................................... 8
4
INSTALLATION................................................................................................... 10
5
6
7
4.1
Overview ............................................................................................................. 10
4.2
Lifting Instructions............................................................................................. 10
OPERATION ....................................................................................................... 11
5.1
Overview ............................................................................................................. 11
5.2
Connections and control devices.....................................................................13
5.3
Water connection ............................................................................................... 13
5.4
Starting procedure ............................................................................................. 13
5.5
Function explanations ....................................................................................... 14
5.6
Wire feed pressure............................................................................................. 15
5.7
Changing and loading wire ............................................................................... 15
5.8
Changing feed rollers ........................................................................................ 15
MAINTENANCE .................................................................................................. 16
6.1
Overview ............................................................................................................. 16
6.2
Inspection and cleaning .................................................................................... 16
ORDERING SPARE PARTS ............................................................................... 17
DIAGRAM .................................................................................................................. 18
WEAR PARTS............................................................................................................20
ORDERING NUMBERS .............................................................................................24
ACCESSORIES .........................................................................................................25
Rights reserved to alter specifications without notice.
0463 363 001
© ESAB AB 2013
1 SAFETY
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment when it
is started up.
○ no-one is unprotected when the arc is struck
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves.
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could
become trapped or cause burns.
5. General precautions:
○ Make sure the return cable is connected securely.
○ Work on high voltage equipment may only be carried out by a qualified electrician.
○ Appropriate fire extinquishing equipment must be clearly marked and close at hand.
○ Lubrication and maintenance must not be carried out on the equipment during
operation.
0463 363 001
-4-
© ESAB AB 2013
1 SAFETY
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting. Ask for your employer's safety practices which should
be based on manufacturers' hazard data.
ELECTRIC SHOCK - Can kill
•
•
•
•
Install and earth the unit in accordance with applicable standards
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
Insulate yourself from earth and the workpiece
Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
•
•
Keep your head out of the fumes
Use ventilation, extraction at the arc, or both, to take fumes and gases away
from your breathing zone and the general area
ARC RAYS - Can injure eyes and burn skin
•
•
Protect your eyes and body. Use the correct welding screen and filter lens and
wear protective clothing
Protect bystanders with suitable screens or curtains
FIRE HAZARD
•
Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
NOISE - Excessive noise can damage hearing
•
•
Protect your ears. Use earmuffs or other hearing protection. Protect your ears.
Use earmuffs or other hearing protection
Warn bystanders of the risk
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION!
Read and understand the instruction manual before
installing or operating.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of
class A equipment in those locations, due to conducted
as well as radiated disturbances.
0463 363 001
-5-
© ESAB AB 2013
1 SAFETY
CAUTION!
This product is solely intended for arc welding.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2002/96/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law, electrical
and/or electronic equipment that has reached the end of
its life must be disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
0463 363 001
-6-
© ESAB AB 2013
2 INTRODUCTION
2
INTRODUCTION
2.1
Overview
The Warrior Feed 304, Warrior Feed 304w wire feed unit is intended for MIG/MAG-welding
together with welding power sources:
•
•
Warrior 400i CC/CV
Warrior 500i CC/CV
They come in different variants, see chapter "Order Number".
The wire feed units are sealed and contain four-wheel drive wire feed mechanisms as well as
control electronics.
They can be used together with wire from ESAB's MarathonPac, or from wire bobbin
(standard Ø 200 mm, Ø 300 mm and accessory Ø 440 mm).
The wire feed unit can be placed on a trolley, suspended above the workplace with a lifting
eye, on a counter balance or on the floor with or without wheel set.
ESAB's accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.2
Equipment
The Warrior Feed 304, Warrior Feed 304w wire feed unit is supplied with:
•
•
Instruction manual
Sticker with recommended wear parts
0463 363 001
-7-
© ESAB AB 2013
3 TECHNICAL DATA
3
TECHNICAL DATA
Warrior Feed 304, Warrior Feed 304w
Power Supply voltage
42 V AC, 50–60 Hz
Power requirement
252 VA
Rated supply current I1
6A
Settings data
Wire feed speed
1.5–25.0 m/min (4.9–82 ft/min)
Creep start
OFF or ON
2/4 stroke
2 stroke or 4 stroke
Wire selection
Solid or Cored
Torch connection
EURO
Max. diameter wire bobbin
300 mm (*440 mm), 12 inch (*17 inch)
Wire dimension
Fe
0.6–1.6 mm (0.023 – 1/16 inch)
SS
0.8–1.6 mm (0.030 – 1/16 inch)
Al
1.0 & 1.6 mm (0.40 & 1/16 inch)
Cored wire
0.9–1.6 mm (0.035 – 1/16 inch)
Weight
WF 304 with bobbin cover
14.4 kg (31.7 Ibs)
WF 304w with bobbin cover
14.7 kg (32.4 Ibs)
Weight wire spool (ESAB standard)
Ø 200 mm
5 kg (11.0 lbs)
Ø 300 mm
18 kg (39.7 lbs)
Ø 440 mm
30 kg (66.1 lbs)
Dimensions (l × w × h)
basic
675 × 265 × 418 mm (26.6 × 10.4 × 16.5
inch)
Operating temperature
-10° to +40°C (+14° to +104°F)
Transport and storage temperature
-20° to +55°C (-4° to +131°F)
Shielding gas
max pressure
All types intended for MIG/MAG welding
5 bar (0.5 Mpa)
Coolant (Warrior Feed 304w)
max pressure
ESAB's ready mixed coolant
5 bar (0.5 Mpa)
Permissible load at
60% duty cycle
500 A
100% duty cycle
400 A
Enclosure class
IP23
with the Ø 440 mm (Ø 17 inch) bobbin and/or the counter balance device
IP2X
* See the "ACCESSORIES" chapter in the instruction manual.
0463 363 001
-8-
© ESAB AB 2013
3 TECHNICAL DATA
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40°C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Equipment marked IP2X is intended for indoor use.
0463 363 001
-9-
© ESAB AB 2013
4 INSTALLATION
4
INSTALLATION
4.1
Overview
The installation must be carried out by a professional.
WARNING!
When welding in an environment with increased electrical danger, only power
sources intended for this environment may be used. These power sources are
marked with the symbol
4.2
.
Lifting Instructions
CAUTION!
Risk of crushing when lifting the wire feeder. Mounting a large wire bobbin (Ø 440
mm), may change the centre of gravity of the wire feeder and increase the risk of
tipping and crushing. Protect yourself and warn bystanders of the risk.
CAUTION!
To avoid personal injury and / or equipment damage, lift using method and
attachment points shown here.
Ordering number for the lifting eye can be found in chapter "Order Number".
NOTE!
If another mounting device is used, this should be insulated from the wire feed
unit.
0463 363 001
- 10 -
© ESAB AB 2013
5 OPERATION
5
OPERATION
5.1
Overview
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
WARNING!
To avoid shock, do not touch electrode wire or parts in contact with it, or
uninsulated cable or connections.
NOTE!
When moving the equipment, use handle intended for transportation. Never pull
the equipment by the welding torch.
WARNING!
Assure that the side panels are closed during operation.
WARNING!
To prevent the reel from sliding off
the hub: Lock the reel in place by
turning the red knob as shown on
the warning label attached next to
the hub.
0463 363 001
- 11 -
© ESAB AB 2013
5 OPERATION
CAUTION!
Before threading welding wire, make sure the chisel point and burrs have been
removed from the end of the wire to prevent the wire from jamming in the torch
liner.
WARNING!
Rotating parts can cause injury, take great care.
WARNING!
There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm.
Secure the equipment, especially if used on an uneven or sloping surface.
0463 363 001
- 12 -
© ESAB AB 2013
5 OPERATION
5.2
1.
2.
3.
4.
Connections and control devices
Display voltage (V)
Display current (A)
Knob for setting the wire feed speed
Knob for setting the voltage
5. Switch for wire inching or gas purge
9. Switch for 4 stroke / 2 stroke (inside)
10. Switch for Cored wire / Solid wire (inside)
11. Switch for Creep start (inside)
12. Connection for welding current from power
source (OKC)
13. Connection for control cable from power
source
14. Connection for shielding gas
6. Connection RED for cooling water from
welding torch *)
7. Connection BLUE for cooling water to the 15. Connection BLUE for cooling water from
welding torch *)
power source (cooling unit) *)
8. Connection for the welding torch
16. Connection RED for cooling water to
power source (cooling unit) *)
NOTE!
*) Cooling water connections only available on certain models.
5.3
Water connection
When connecting a water-cooled welding torch, the main power supply switch of the power
source must be in the OFF position and the cooling unit switch must be in position 0.
A water connection kit can be orderred as accessory, see chapter "Accessories".
5.4
Starting procedure
When the wire feed starts, the power source generates welding voltage.
If there is no welding current flow within three seconds, the power source switches the
welding voltage off. The wire feed continues until the welding torch's switch is switched off.
0463 363 001
- 13 -
© ESAB AB 2013
5 OPERATION
5.5
Function explanations
Open the lid for access to the 4 stroke/2 stroke, the Cored/Solid wire and the Creep start
functions.
2-stroke
With 2-stroke gas pre-flow (if used) starts when the welding torch trigger switch
is pressed. The welding process then starts. Releasing the trigger switch stops
welding entirely and starts gas post-flow (if selected).
4-stroke
With 4 stroke, the gas pre-flow starts when the welding torch trigger switch is
pressed in and the wire feed starts when it is released. The welding process
continues until the switch is pressed in again, the wire feed then stops and when
the switch is released the gas post-flow starts (if selected).
Wire selection – Cored wire
A constant burnback time is selected when the trigger is released to adapt to
welding with cored wire.
Wire selection – Solid wire
Short Circuit Termination (SCT) behavior is selected when the trigger is released
to adapt to welding with solid wire.
SCT is a new way to stop the welding with some small short circuits to reduce
the end crater and oxidation. It also gives the advantage of a good start
performance with solid wire.
Creep start
Creep starting feeds out the wire at 9 m/min (29.5 ft/min) until it makes electrical
contact with the workpiece.
Wire inching
Wire inching is used when one needs to feed wire without welding voltage being
applied. The wire is fed as long as the button is depressed.
Gas purging
Gas purging is used when measuring the gas flow or to flush any air or moisture
from the gas hoses before welding starts. Gas purging occurs for as long as the
button is held depressed and occurs without voltage or wire feed starting.
Wire feed speed
This sets the required feed speed of the filler wire in m/minute.
0463 363 001
- 14 -
© ESAB AB 2013
5 OPERATION
5.6
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then set the
pressure of the wire feeder's pressure rollers. It is important that the pressure is not too high.
Figure A
Figure B
To check that the feed pressure is set correctly, you can feed out the wire against an
insulated object, e.g. a piece of wood.
When you hold the welding torch approx. 5 mm from the piece of wood (figure A) the feed
rollers should slip.
If you hold the welding torch approx. 50 mm from the piece of wood, the wire should be fed
out and bend (figure B).
5.7
•
•
•
•
•
•
Open the side panel.
Disconnect the pressure sensor by folding it backwards, the pressure rollers slide up.
Straighten out the new wire 10-20 cm. File away burrs and sharp edges from the end of
the wire before inserting it into the wire feed unit.
Make sure that the wire goes properly into the feed roller's track and into the outlet nozzle
or wire guide.
Secure the pressure sensor.
Close the side panel.
5.8
•
•
•
Changing and loading wire
Changing feed rollers
Open the side panel.
Disconnect the pressure sensor (1) by
folding it backwards.
Disconnect the pressure rollers (2) by
turning the axle (3) 1/4 turn clockwise and
pulling out the axle.
The pressure rollers disconnect
•
Disconnect the feed rollers (4) by
unscrewing the nuts (5) and pulling out
the rollers.
During installation, repeat the above in the reverse order.
Choice of track in the feed rollers
Turn the feed roller with the dimensioning mark for the required track towards you.
0463 363 001
- 15 -
© ESAB AB 2013
6 MAINTENANCE
6
MAINTENANCE
6.1
Overview
NOTE!
Regular maintenance is important for safe, reliable operation.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.2
Inspection and cleaning
Wire feed unit
Check regularly that the wire feed unit is not clogged with dirt.
•
Cleaning and replacement of the wire feed unit mechanism's worn parts should take
place at regular intervals in order to achieve trouble-free wire feed. Note that if
pre-tensioning is set too hard, this can result in abnormal wear on the pressure roller,
feed roller and wire guide.
The brake hub
The hub is adjusted when delivered, if readjustment is required, follow the instructions below.
Adjust the brake hub so that wire is slightly slack when wire feed stops.
•
Adjusting the braking torque:
○ Turn the red handle to the locked
position.
○ Insert a screwdriver into the springs in
the hub.
Turn the springs clockwise to reduce the
braking torque.
Turn the springs counter-clockwise to
increase the braking torque.
Note: Make sure you turn both springs
the same amount.
Welding torch
•
Cleaning and replacement of the welding torch's wear parts should take place at regular
intervals in order to achieve trouble-free wire feed. Blow the wire guide clean regularly
and clean the contact tip.
0463 363 001
- 16 -
© ESAB AB 2013
7 ORDERING SPARE PARTS
7
ORDERING SPARE PARTS
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
The Warrior Feed 304 is designed and tested in accordance with international and
European standards IEC/EN 60974-5 and IEC/EN 60974-10, Canadian standard
CAN/CSA-E60974-5 and US standard ANSI/IEC 60974-5. On completion of service or
repair work, it is the responsibility of the person(s) performing the work to ensure that the
product still complies with the requirements of the above standards.
Spare parts may be ordered through your nearest ESAB dealer, see the back cover of this
document. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
0463 363 001
- 17 -
© ESAB AB 2013
DIAGRAM
DIAGRAM
0463 363 001
- 18 -
© ESAB AB 2013
DIAGRAM
0463 363 001
- 19 -
© ESAB AB 2013
WEAR PARTS
WEAR PARTS
Item
Ordering
number
Denomination
Wire type
Wire dimensions
HI 1 0455 072 002
0456 615 001
Intermediate nozzle Fe, Ss & cored Ø 2.0 mm steel for 0.6-1.6 mm
Intermediate nozzle Al
Ø 2.0 mm plastic for 0.8-1.6 mm
HI 2 0469 837 880
0469 837 881
Outlet nozzle
Outlet nozzle
HI 3 0191 496 114
Key
HI 4 0215 701 007
Locking washer
HI 5a 0459 440 001
Motor gear euro,
drive gear
Item
Ordering
number
Denomination
Fe, Ss & cored Ø 2.0 mm steel for 0.6-1.6 mm
Al
Ø 2.0 mm plastic for 0.8-1.6 mm
Wire
type
Wire dimensions (mm)
Groove
type
Roller
markings
HI 5b 0459 052 001 Feed/pressure rollers Fe, Ss Ø 0.6 & 0.8
& cored
V
0.6 & 0.8 S2
0459 052 002 Feed/pressure rollers Fe, Ss Ø 0.8 & 1.0
& cored
V
0.8 & 1.2 S2
0459 052 003 Feed/pressure rollers Fe, Ss Ø 0.9/1.0 & 1.2
& cored
V
1.0 & 1.2 S2
0459 052 013 Feed/pressure rollers Fe, Ss Ø 1.4 & 1.6
& cored
V
1.4 & 1.6 S2
0458 825 001 Feed/pressure rollers Cored
Ø 0.9/1.0 & 1.2
V1.0 & 1.2 R2
knurled
0458 825 010 Feed/pressure rollers Cored
Ø 1.2 & 1.2
V1.2 & 1.2 R2
knurled
0458 825 002 Feed/pressure rollers Cored
Ø 1.2 & 1.4
V1.2 & 1.4 R2
knurled
0458 825 003 Feed/pressure rollers Cored
Ø 1.6
V1.6 & 2.0 R2
knurled
0458 824 001 Feed/pressure rollers Al
Ø 0.8 & 0.9/1.0
U
0.8 & 1.0 A2
0458 824 002 Feed/pressure rollers Al
Ø 1.0 & 1.2
U
1.0 & 1.2 A2
0458 824 003 Feed/pressure rollers Al
Ø 1.2 & 1.6
U
1.2 & 1.6 A2
Only use pressure and feed rollers marked A2, R2 or S2.
The rollers are marked with wire dimension in mm, some are also marked with inch.
0463 363 001
- 20 -
© ESAB AB 2013
WEAR PARTS
0463 363 001
- 21 -
© ESAB AB 2013
WEAR PARTS
Item Ordering number Denomination
Notes
HI 6
Washer
Ø 16/5×1
HI 7
Screw
M4×12
HI 8
Screw
M6×12
HI 9
Washer
Ø 16/8.4×1.5
HI 10 0469 838 001
Cover
HI 11 0458 722 880
Axle and Nut
HI 12 0459 441 880
Gear adapter
HI 13 0455 049 001
Inlet nozzle
HI 14 0458 999 001
Shaft
HI 15
Nut
HI 16 0458 748 002
Insulating
washer
HI 17 0458 748 001
Insulating
bushing
Item
Ordering
number
HI 18 0156 602 001
Denomination
Inlet nozzle
Ø 3mm for 0.6-1.6mm Fe, Ss, Al and cored wire
M10
Wire type
Ø 16/5×1
Wire dimensions
Ø 2mm plastic for 0.6-1.6mm
Welding with aluminium wire
In order to weld with aluminium wire, U-shaped rollers, nozzles and liners for aluminium wire
must be used. It is recommended to use 3 m long welding torch for aluminium wire,
equipped with appropriate wear parts.
0463 363 001
- 22 -
© ESAB AB 2013
WEAR PARTS
0463 363 001
- 23 -
© ESAB AB 2013
ORDERING NUMBERS
ORDERING NUMBERS
Ordering Number
Denomination
0465 427 880
Warrior ™ Feed 304
0465 427 881
Warrior ™ Feed 304w
0459 839 092
Spare parts list
Type
with water cooling
Technical documentation is available on the Internet at www.esab.com.
0463 363 001
- 24 -
© ESAB AB 2013
ACCESSORIES
ACCESSORIES
0458 674 980
Bobbin cover kit, plastic Ø 300 mm
0458 707 880
Wheel kit
0458 707 881
Wheel kit
0459 233 880
Adapter for Ø 440 mm bobbin
Note! IPS23 not valid for wire feeder with Ø
400 mm bobbin.
0458 706 880
Lifting eye
0457 341 881
Strain relief for welding torch
0463 363 001
- 25 -
© ESAB AB 2013
ACCESSORIES
F102 440 880
Quick connector MarathonPac ™
0459 234 880
Strain relief bracket for connection set
0465 451 880
Remote kit
0459 491 895
Remote control unit M1
MIG/MAG: wire feed speed and voltage
0465 510 880
Trolley
0459 553 880
Remote cable 23 pole - 8 pole 5 m
0463 363 001
- 26 -
© ESAB AB 2013
ACCESSORIES
0465 276 881
Water kit
0458 705 880
Counter balance device (includes mast and
counterbalance)
Note! IPS23 not valid for wire feeder with
counterbalance arm.
Welding torch MXH 400w PP Note! MXH PP only recommended for Feed304/3004/L3004
0700 200 015
6m
0700 200 016
10 m
0700 200 019
10 m, 45°
Welding torch MXH 300w PP Note! MXH PP only recommended for Feed304/3004/L3004
0700 200 017
6m
0700 200 018
10 m
0700 200 020
10 m, 45°
Connection set, 70 mm², 19 poles
0459 836 880
1.7 m
0459 836 881
5m
0459 836 882
10 m
0459 836 883
15 m
0459 836 884
25 m
0459 836 885
35 m
0463 363 001
- 27 -
© ESAB AB 2013
ACCESSORIES
Connection set water, 70 mm², 19 poles
0459 836 890
1.7 m
0459 836 891
5m
0459 836 892
10 m
0459 836 893
15 m
0459 836 894
25 m
0459 836 895
35 m
Connection set, 95 mm², 19 poles
0459 836 980
1.7 m C
0459 836 981
5mC
0459 836 982
10 m C
0459 836 983
15 m C
0459 836 984
25 m C
0459 836 985
35 m C
Connection set water, 95 mm², 19 poles
0459 836 990
1.7 m A
0459 836 991
5mC
0459 836 992
10 m A
0459 836 993
15 m C
0459 836 994
25 m C
0459 836 995
35 m C
0463 363 001
- 28 -
© ESAB AB 2013
ACCESSORIES
0463 363 001
- 29 -
© ESAB AB 2013
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
BULGARIA
ESAB Kft Representative Office
Sofia
Tel: +359 2 974 42 88
Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
www.esab.com
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
SOUTH AFRICA
ESAB Africa Welding & Cutting
Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
USA
ESAB Welding & Cutting
Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising