Dell 7700HD Projector electronics accessory User's Guide


Add to my manuals
122 Pages

advertisement

Dell 7700HD Projector electronics accessory User's Guide | Manualzz

Dell™ 7700FullHD Projector

User’s Guide

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

© 2012 Dell Inc. All rights reserved.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of

Dell Inc.; DLP and DLP logo are trademarks of T

EXAS

I

NSTRUMENTS

I NCORPORATED ; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model 7700FullHD

March 2012 Rev. A00

Contents

1 Your Dell Projector

. . . . . . . . . . . . . . . . . .

7

About Your Projector

. . . . . . . . . . . . . . . . . 8

2 Connecting Your Projector

. . . . . . . . . . . .

10

Installing the Optional Wireless Dongle

. . . . . . 11

Connecting to a Computer

. . . . . . . . . . . . . . . .

12

Connecting a Computer Using a VGA Cable

. . . . 12

Monitor Loop-Through Connection Using

VGA Cables

. . . . . . . . . . . . . . . . . . . . . 13

Connecting a Computer Using a RS232 Cable

. . . 14

Connecting a Computer by USB Cable

. . . . . . . 15

Connecting a Computer Using Wireless Dongle

(Optional)

. . . . . . . . . . . . . . . . . . . . . . 16

Connecting a DVD Player

. . . . . . . . . . . . . . . .

17

Connecting a DVD Player Using an S-Video Cable

. 17

Connecting a DVD Player Using a

Composite Video Cable

. . . . . . . . . . . . . . . 18

Connecting a DVD Player Using a

Component Video Cable

. . . . . . . . . . . . . . 19

Connecting a DVD Player Using a 3 RCA

Component Video Cable

. . . . . . . . . . . . . . 20

Connecting a DVD Player Using an HDMI Cable

. . 21

Connecting to Local Area Network

. . . . . . . . . . .

22

To project an image and control the projector that is connected to a network through a RJ45 cable.

. . 22

Contents 3

Professional Installation Options: Installation for

Driving Automatic Screen

. . . . . . . . . . . . . 23

Connection With Commercial RS232 Control Box

. 24

3 Using Your Projector

. . . . . . . . . . . . . . . .

25

Turning Your Projector On

. . . . . . . . . . . . . . . .

25

Turning Your Projector Off

. . . . . . . . . . . . . . . .

25

Adjusting the Projected Image

. . . . . . . . . . . . .

26

Raising the Projector Height

. . . . . . . . . . . . 26

Lowering the Projector Height

. . . . . . . . . . . 26

Adjusting the Projector Zoom and Focus

. . . . . . . .

27

Adjusting Projection Image Size

. . . . . . . . . . . .

28

Using the Control Panel

. . . . . . . . . . . . . . . . .

30

Using the Remote Control

. . . . . . . . . . . . . . . .

32

Installing the Remote Control Batteries

. . . . . . . .

35

Operating Range With Remote Control

. . . . . . . . .

36

Using the On-Screen Display

. . . . . . . . . . . . . .

37

INPUT SOURCE

. . . . . . . . . . . . . . . . . . . 37

AUTO ADJUST

. . . . . . . . . . . . . . . . . . . 38

BRIGHTNESS/CONTRAST

. . . . . . . . . . . . . 39

VIDEO MODE

. . . . . . . . . . . . . . . . . . . . 39

VOLUME

. . . . . . . . . . . . . . . . . . . . . . 40

AUDIO INPUT

. . . . . . . . . . . . . . . . . . . . 40

ADVANCED SETTINGS

. . . . . . . . . . . . . . . 40

LANGUAGE

. . . . . . . . . . . . . . . . . . . . . 54

HELP

. . . . . . . . . . . . . . . . . . . . . . . . 54

4 Contents

Wireless Networking Installation

. . . . . . . . . . . .

55

Enable Wireless on the Projector

. . . . . . . . . . 56

Install the Wireless Application Software on Your

Computer

. . . . . . . . . . . . . . . . . . . . . . 58

Launch the Wireless Application

. . . . . . . . . . 61

Presentation to Go (PtG) Installation

. . . . . . . . . .

65

PtG Viewer

. . . . . . . . . . . . . . . . . . . . . 66

Photo Viewer

. . . . . . . . . . . . . . . . . . . . 66

PtG/Photo Function Introduction

. . . . . . . . . . 67

PtG Overview

. . . . . . . . . . . . . . . . . . . . 67

Photo Overview

. . . . . . . . . . . . . . . . . . . 68

Buttons-Introduction

. . . . . . . . . . . . . . . . 68

Install the PtG Converter Application Software on

Your Computer

. . . . . . . . . . . . . . . . . . . 69

Using the PtG Converter

. . . . . . . . . . . . . . 70

Audio Projection Installation

. . . . . . . . . . . . . .

71

Enable Wireless or LAN on the Projector

. . . . . 72

Install the Wireless Application Software on

Your Computer

. . . . . . . . . . . . . . . . . . . 73

Launch the Wireless Application

. . . . . . . . . . 74

Login

. . . . . . . . . . . . . . . . . . . . . . . . 75

Video Stream Installation

. . . . . . . . . . . . . . . .

76

Video Stream Support Format

. . . . . . . . . . . 76

Enable Wireless or LAN on the Projector

. . . . . 77

Install the Wireless Application Software on

Your Computer

. . . . . . . . . . . . . . . . . . . 77

Launch the Wireless Application

. . . . . . . . . . 77

Login

. . . . . . . . . . . . . . . . . . . . . . . . 77

Managing the Projector From Web Management

. . . .

78

Configuring the Network Setting

. . . . . . . . . . 78

Contents 5

Accessing Web Management

. . . . . . . . . . . 78

Make Application Token

. . . . . . . . . . . . . . . .

99

4 Troubleshooting Your Projector

. . . . . .

101

Guiding Signals

. . . . . . . . . . . . . . . . . . . . .

105

Changing the Lamp

. . . . . . . . . . . . . . . . . . .

106

5 Specifications

. . . . . . . . . . . . . . . . . . . .

108

6 Contacting Dell

. . . . . . . . . . . . . . . . . . .

115

7 Appendix: Glossary

. . . . . . . . . . . . . . .

116

6 Contents

1

Your Dell Projector

Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell™ if anything is missing.

Package Contents

Power cable 1.8 m VGA cable (VGA to VGA)

1.8 m USB cable (USB-A to USB-B) Remote control

CD User’s Guide and Documentation AAA Batteries (2)

Informacion Importante

Dell

TM 7700FullHD Projector

Quick Setup Guide

AAA

AAA

DOCOMENTATION

DellTM 7700FullHD Pr ojector

Dell

TM oduct Inf

Projector s orma tion Guide

Your Dell Projector 7

About Your Projector

Top View

2 1

Bottom View

202.50

11 9

7

3

6

4

5

10 8

55.00 55.00

10

1

2

Control panel

3

4

IR receivers

Focus ring

5

6

Lens

Elevator button for height adjustments

7

Lens cap

Mounting holes for ceiling mount: Screw hole M3 x 6.5 mm depth.

Recommended torque <8 kgf-cm

8

9

Mounting hole for tripod: Insert nut 1/4"*20 UNC

Lamp cover

10 Tilt adjustment wheel

11 Elevator foot

CAUTION: Safety Instructions

1 Do not use the projector near appliances that generate a lot of heat.

2 Do not use the projector in areas where there is an excessive amount of dust. The dust may cause the system to fail and the projector will automatically shut down.

3 Ensure that the projector is mounted in a well-ventilated area.

4 Do not block the ventilation slots and openings on the projector.

5 Ensure the projector operates between ambient temperatures (5 ºC to 35 ºC).

8 Your Dell Projector

6 Do not try to touch the ventilation outlet as it can become very hot after the projector has been turned on or immediately after it is turned off.

7 Do not look into the lens while the projector is on as it may cause injury to your eyes.

8 Do not place any objects near or in front of the projector or cover its lens while the projector is on as the heat may cause the object to melt or burn.

9 Do not use the wireless projector near cardiac pacemakers.

10 Do not use the wireless projector near medical equipment.

11 Do not use the wireless projector near microwave ovens.

NOTE:

• Do not attempt to ceiling mount the projector yourself. It should be installed by a qualified technician.

• Recommended Projector Ceiling Mount Kit (P/N: C3505). For more information, see the Dell Support website at support.dell.com.

• For more information, see the Safety Information that shipped with your projector.

• The 7700FullHD projector can only be used indoors.

Your Dell Projector 9

Connecting Your Projector

1 2 3 4 5 6 7 8 9 10 11

2

19 18 17 16 15 14 13 12

1 WiFi USB (Type A) connector

2 USB Type B connector for USB

Display

3 USB Type A connector for USB

Viewer

4 RJ45 connector

5 S-Video connector

6 Composite Video connector

7 RS232 (D-sub) connector

8 Mini USB (Mini Type B) connector for remote control

9 Audio output connector

10 Audio input connector

11 +12 V DC out connector

12 Security cable slot

13 Component Video input connector

14 Power cord connector

15 VGA-A output (monitor loopthrough) connector

16 VGA-B input (D-sub) connector

17 VGA-A input (D-sub) connector

18 HDMI-B connector

19 HDMI-A connector

10 Connecting Your Projector

CAUTION: Before you begin any of the procedures in this section, follow the

Safety Instructions as described on page 8.

Installing the Optional Wireless Dongle

Your projector must be installed with a wireless dongle if you want to use the

wireless networking option. Refer to "Wireless Networking Installation" on page 55. The wireless dongle is not shipped with your projector. You can

purchase it on the Dell website at www.dell.com.

1 Unscrew and take off the wireless cover.

2 Plug in the wireless dongle.

3 Assemble the wireless cover.

Connecting Your Projector 11

Connecting to a Computer

Connecting a Computer Using a VGA Cable

2 3

MOLEX

1

1

2

3

Power cord

VGA to VGA cable

USB-A to Mini USB-B cable

NOTE: The Mini USB cable must be connected if you want to use the Page Up and Page Down features on the remote control.

NOTE: The Mini USB cable is not shipped with your projector. You can purchase the Mini USB cable on the Dell website at www.dell.com.

12 Connecting Your Projector

Monitor Loop-Through Connection Using VGA Cables

2

2

1

1

2

Power cord

VGA to VGA cable

NOTE: Only one VGA cable is shipped with your projector. An additional VGA cable can be purchased on the Dell website at www.dell.com.

Connecting Your Projector 13

Connecting a Computer Using a RS232 Cable

1

2

1

2

Power cord

RS232 (9-pin D-sub female to female pin2-3 swap) cable

NOTE: The RS232 (9-pin D-sub female to female pin2-3 swap) cable is not shipped with your projector. Consult a professional installer for the cable and

RS232 remote control software.

14 Connecting Your Projector

Connecting a Computer by USB Cable

1

MOLEX

2

1

2

Power cord

USB-A to USB-B cable

NOTE: Plug and Play. Only one USB cable is shipped with your projector. An additional USB cable can be purchased on the Dell website at www.dell.com.

Connecting Your Projector 15

Connecting a Computer Using Wireless Dongle (Optional)

NOTE: Your computer should be equipped with a wireless connector and properly configured to detect another wireless connection. Refer to your computer’s documentation on how to configure a wireless connection.

NOTE: Your projector must be installed with a wireless dongle if you want to

use the wireless networking. Refer to "Wireless Networking Installation" on page 55.

16 Connecting Your Projector

Connecting a DVD Player

Connecting a DVD Player Using an S-Video Cable

1

2

1

2

Power cord

S-Video cable

NOTE: The S-Video cable is not shipped with your projector. You can purchase the S-Video extension (50 ft/100 ft) cable on the Dell website at www.dell.com.

Connecting Your Projector 17

Connecting a DVD Player Using a Composite Video Cable

2

1

1

2

Power cord

Composite Video cable

NOTE: The Composite Video cable is not shipped with your projector. You can purchase the Composite Video Extension (50 ft/100 ft) cable on the Dell website at www.dell.com.

18 Connecting Your Projector

Connecting a DVD Player Using a Component Video Cable

2

1

1

Power cord

2 VGA to Component Video cable

NOTE: The VGA to Component Video cable is not shipped with your projector. the Dell website at www.dell.com.

You can purchase the VGA to Component Video Extension (50 ft/100 ft) cable on

Connecting Your Projector 19

Connecting a DVD Player Using a 3 RCA Component Video Cable

1

2

1

2

Power cord

3 RCA to 3 RCA Component Video (Male to Male) cable

NOTE: The 3 RCA to 3 RCA Component Video (Male to Male) cable is not shipped with your projector. You can purchase the 3 RCA to 3 RCA Component

Video (Male to Male) cable Extension (50 ft/100 ft) cable on the Dell website at www.dell.com.

20 Connecting Your Projector

Connecting a DVD Player Using an HDMI Cable

2

1

1

Power cord

2 HDMI cable

NOTE: The HDMI cable is not shipped with your projector. You can purchase the HDMI cable on the Dell website at www.dell.com.

Connecting Your Projector 21

Connecting to Local Area Network

To project an image and control the projector that is connected to a network through a RJ45 cable.

1

Local Area Network (LAN)

1

2

Power cord

RJ45 cable

NOTE: The RJ45 cable is not shipped with your projector. You can purchase the

RJ45 cable on the Dell website at www.dell.com.

22 Connecting Your Projector

Professional Installation Options: Installation for Driving Automatic

Screen

3

1

2

1

2

3

Power cord

12 V DC Plug

Motorized projection screen

NOTE: Use a 12 V DC plug in, 1.7 mm (ID) x 4.00 mm (OD) x 9.5 mm (shaft), to connect the automatic screen to the projector.

12 V DC Plug

Connecting Your Projector 23

Connection With Commercial RS232 Control Box

3

1

2

1

2

3

Power cord

RS232 (9-pin D-sub female to female pin2-3 swap) cable

Commercial RS232 control box

NOTE: The RS232 (9-pin D-sub female to female pin2-3 swap) cable is not shipped with your projector. Consult a professional technician to obtain the cable.

24 Connecting Your Projector

3

Using Your Projector

Turning Your Projector On

NOTE: Turn on the projector before you turn on the source (computer, DVD player, etc.). The Power button light blinks blue until pressed.

1 Remove the lens cap.

2 Connect the power cord and appropriate signal cables to the projector. For

information about connecting the projector, see "Connecting Your Projector" on page 10.

3

Press the Power button (see "Using the Control Panel" on page 30 to locate the

Power button).

4 Turn on your source (computer, DVD player, etc.)

5 Connect your source to the projector using the appropriate cable. See

"Connecting Your Projector" on page 10 for instructions to connect your source to

the projector.

6 By default, the input source of the projector is set to VGA-A. Change the input source of the projector if necessary.

7 If you have multiple sources connected to the projector, press the Source button

on the remote control or control panel to select the desired source. See "Using the

Control Panel" on page 30 and "Using the Remote Control" on page 32 to locate

the Source button.

Turning Your Projector Off

CAUTION: Unplug the projector after properly shutting down as explained in the following procedure.

1 Press the Power button. Follow the instruction displayed on screen to properly turn off the projector.

NOTE: The "Press Power Button to Turn off Projector" message will appear on the screen. The message disappears after 5 seconds or you can press the Menu button to clear it.

2 Press the Power button again. The cooling fans continue to operate for 120 seconds.

Using Your Projector 25

3 To power off the projector quickly, press the Power button and hold for 1 second while the projector’s cooling fans are still running.

NOTE: Before you turn on the projector again, wait for 60 seconds to allow the internal temperature to stabilize.

4 Disconnect the power cord from the electrical outlet and the projector.

Adjusting the Projected Image

Raising the Projector Height

1 Press the Elevator button.

2 Raise the projector to the desired display angle, and then release the button to lock the elevator foot into position.

3 Use the tilt adjustment wheel to fine-tune the display angle.

Lowering the Projector Height

1 Press the Elevator button.

2 Lower the projector, then release the button to lock the elevator foot into position.

1

1

2

3

3 3

Elevator button

Elevator foot (Angle of tilt: 0 to 8 degrees)

Tilt adjustment wheel

26 Using Your Projector

2

Adjusting the Projector Zoom and Focus

CAUTION: To avoid damaging the projector, ensure that the side door is fully closed and the elevator foot is fully retracted before moving the projector.

1 Open the side door of the projector.

2 Unlock the lens shift lock, before you adjust the lens shift.

3 Turn the vertical/horizontal lens shift knob to shift the lens.

4 After adjusting the lens shift, lock the lens shift lock.

5 Pull the zoom ring adjustment up and down to zoom in and out.

6 Rotate the focus ring until the image is clear. THe projector focuses at distances ranging between 3.28 ft to 39.37 ft (1.0 m to 12.0 m).

7 Close the side door of the projector.

1 2 34 5 6

1

2

3

4

5

6

Side door

Vertical lens shift knob

Lens shift lock

Horizontal lens shift knob

Zoom ring

Focus ring

Using Your Projector 27

Adjusting Projection Image Size

292.9" (743.97 cm)

244.17"

(620.19 cm)

239.29" (607.80 cm)

199.40"

(506.48 cm)

188.01" (477.55 cm)

156.67"

(397.94 cm) 134.29" (341.10 cm)

111

.91

"

(284.25 cm)

83.02" (210.87 cm)

69.18"

(175.72 cm)

24.42" (62.03 cm)

20.3"

(51.56 cm)

3.28' (1.0 m)

28 Using Your Projector

(Min zoom)

Desired

Distance (m)

<A>

Screen size

Diagonal

(inch)

<B>

H (cm)

Top

From base to

W (cm) x top of image

(cm)

<C>

1

3.4

20.3

69.18

45 x 25

153 x 86

29

99

5.5

7.7

9.8

12

111.91

248 x 139

156.67

347 x 195

199.4

244.17

441 x 248

541 x 304

160

224

286

350

Diagonal

(inch)

<B>

24.42

83.02

(Max zoom)

Screen size Top

From base to

W (cm) x top of image

H (cm) (cm)

<C>

54 x 30

184 x 103

35

119

134.29

297 x 167

188.01

416 x 234

239.29

530 x 298

292.9

649 x 365

192

269

343

420

B

134.29"

Height:

192 cm

C

Distance:

5.5 m

A

Using Your Projector 29

Using the Control Panel

1 2 3

4

5

6

7

9

1 LAMP warning light

8

2

3

TEMP warning light

Power

If the LAMP amber indicator is on or blinking, one of the following problems could be occurring:

• Lamp is reaching its end of usable life

• Lamp module is not properly installed

• Lamp driver failure

• Color wheel failure

For more information, see "Troubleshooting Your

Projector" on page 101 and "Guiding Signals" on page 105.

If the TEMP amber indicator is on or blinking, one of the following problems could be occurring:

• Internal temperature of the projector is too high

• Color wheel failure

For more information, see "Troubleshooting Your

Projector" on page 101 and "Guiding Signals" on page 105.

Turns the projector on or off. For more

information, see "Turning Your Projector On" on page 25 and "Turning Your Projector Off" on page 25.

30 Using Your Projector

4 Volume Control

5 Up / Keystone adjustment

6 Right /

Auto Adjust

Allows you to increase or decrease the volume.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to adjust image distortion caused by tilting the projector (+/-30 degrees).

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to synchronize the projector to the input source.

NOTE: Auto Adjust does not operate if the on-screen display (OSD) is displayed.

7

8

9

IR Receiver Point the remote control towards the IR receiver and press a button.

Down / Keystone Press to navigate through the On-Screen Display adjustment (OSD) Menu items.

Press to adjust image distortion caused by tilting the projector (+/-30 degrees).

Menu

10 Left

11 Enter

/ Source

12 Brightness and

Contrast Control

Press to activate the OSD. Use the directional keys and the Menu button to navigate through the OSD.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to toggle through Analog RGB, Composite,

Component (YPbPr via VGA), HDMI, and

S-Video sources when multiple sources are connected to the projector.

Press to confirm the selection item.

Allows you to adjust the brightness and contrast values.

Using Your Projector 31

Using the Remote Control

11

12

13

14

15

16

17

18

19

1

2

3

4

5

6

7

8

9

10

1

Power

2

3

Enter

Right

4

Down

5

32

Aspect Ratio

Turns the projector on or off. For more information,

see "Turning Your Projector On" on page 25 and

"Turning Your Projector Off" on page 25.

Press to confirm the selection.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to change the aspect ratio of a displayed image.

Using Your Projector

6 Page up

12

Left

Press to move to the previous page.

NOTE: The Mini USB cable must be connected if you want to use the Page Up feature.

Press to mute or un-mute the projector speaker. 7 Mute

8 Page down

9 Video mode

10 Blank screen

11 Up

Press to move to the next page.

NOTE: The Mini USB cable must be connected if you want to use the Page Down feature.

The projector has preset configurations that are optimized for displaying data (presentation slides) or video (movies, games, etc.).

Press the Video Mode button to toggle between

Presentation mode, Bright mode, Movie mode,

sRGB, or Custom mode.

Pressing the Video Mode button once will show the current display mode. Pressing the Video Mode button again will switch between modes.

Press to hide/unhide the image.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to navigate through the On-Screen Display

(OSD) Menu items.

Press to activate the OSD. 13

Menu

14 Volume up Press to increase the volume.

15 Laser Point the remote control at the screen, press and hold the laser button to activate the laser light.

WARNING: Do not look at the laser point when it is active. Avoid directing the laser light on your eyes.

16

Volume down

Press to decrease the volume.

17 Keystone adjustment Press to adjust image distortion caused by tilting the projector (+/-30 degrees).

18 Source Press to switch between Analog RGB, Composite,

Component (YPbPr, via VGA), HDMI, and S-Video source.

Using Your Projector 33

19 Auto Adjust Press to synchronize the projector with the input source. Auto Adjust does not operate if the OSD is displayed.

20 Keystone adjustment Press to adjust image distortion caused by tilting the projector (+/-30 degrees).

34 Using Your Projector

Installing the Remote Control Batteries

NOTE: Remove the batteries from the remote control when not in use.

1 Press the tab to lift the battery compartment cover.

1

2 Check the polarity (+/-) marking on the batteries.

2

3 Insert the batteries and align their polarity correctly according to the marking in the battery compartment.

NOTE: Avoid mixing different types of batteries or using new and old batteries together.

3

4 Slip the battery cover back.

4

Using Your Projector 35

Operating Range With Remote Control

Operating range

Angle ±30°

Distance 7 m/22.97 feet

Angle

Distance

Angle

Distance

NOTE: Actual operating range may slightly differ from the diagram. Weak batteries will also prevent the remote control from properly operating the projector.

36 Using Your Projector

Using the On-Screen Display

• The projector has a multi-language On-Screen Display (OSD) Menu that can be displayed with or without an input source.

• Press the Menu button on the control panel or the remote control to enter the

Main Menu.

• To navigate through the tabs in the Main Menu, press the or buttons on your projector’s control panel or remote control.

• To select a submenu, press the or button on your projector’s control panel or remote control.

• To select an option, press the or buttons on your projector’s control panel or remote control. When an item is selected, the color changes to dark blue.

• Use the or buttons on the control panel or remote control to adjust the settings.

• To go back to the Main Menu, press the button on the control panel or the remote control.

• To exit the OSD, press the Menu button directly on the control panel or the remote control.

INPUT SOURCE

The Input Source menu allows you to select your projector’s input source.

A

UTO

S

OURCE Press to turn on or off Auto Source mode.

VGA-A—Press to detect a VGA-A signal.

VGA-B—Press to detect a VGA-B signal.

HDMI-A—Press to detect a HDMI-A signal.

HDMI-B—Press to detect a HDMI-B signal.

C

OMPONENT Press to detect a RCA Component signal.

C

OMPOSITE Press to detect a Composite Video signal.

S-V

IDEO Press to detect a S-Video signal.

Using Your Projector 37

W IRELESS /USB—Press to activate the Input Source Wireless/USB menu.

NOTE: The Wireless/USB can be used after the "Wireless and LAN" option is turned on.

INPUT SOURCE WIRELESS/USB

The Input Source Wireless/USB menu allows you to activate the Wireless Display,

USB Display, and USB Viewer.

W IRELESS D ISPLAY Press to access the projector's Wireless Guide screen. See

"Wireless Guide screen" on page 57.

USB D ISPLAY Allows you to display the computer/laptop screen to your projector via the USB cable.

USB V

IEWER Allows you to display photo and PPT files from your USB flash drive.

See "Presentation to Go (PtG) Installation" on page 65.

AUTO ADJUST

Auto Adjust automatically adjusts the projector's Horizontal, Vertical, Frequency, and Tracking in PC mode.

38 Using Your Projector

BRIGHTNESS/CONTRAST

The Brightness/Contrast menu allows you adjust the brightness/contrast settings of your projector.

B RIGHTNESS Use and to adjust the brightness of the image.

C

ONTRAST Use and to adjust the display contrast.

NOTE: If you adjust the settings for Brightness and Contrast the projector automatically switch to Custom mode.

VIDEO MODE

The Video Mode menu allows you to optimize the display image: Presentation,

Bright, Movie, sRGB (provides more accurate color representation), and Custom

(set your preferred settings).

Using Your Projector 39

VOLUME

The Volume menu allows you adjust the volume settings of your projector.

V

OLUME Press to increase the volume and to decrease the volume.

AUDIO INPUT

The Audio Input menu allows you to select your audio input source. The options are: Analog In, HDMI-A, HDMI-B, and Wireless/LAN.

ADVANCED SETTINGS

The Advanced Settings menu allows you to change settings for Image, Display,

Projector, LAN, Wireless, Menu, Power, PIP, and Information.

40 Using Your Projector

I MAGE S ETTINGS ( IN PC M ODE )— Select and press to activate image settings.

The image settings menu provides the following options:

C OLOR T EMPERATURE — Allows you to adjust the color temperature. The screen appears cooler at higher color temperatures and warmer at lower color temperatures. When you adjust the values in the Color Adjust menu, the Custom mode is activated. The values are saved in the Custom mode.

RGB C OLOR A DJUST — Allows you to manually adjust the colors red, green, and blue.

W HITE I NTENSITY — Press and use and to display white intensity.

D YNAMIC A PERTURE — Allows you to set the projector dynamic aperture.

The options are: Off, Dynamic, and Auto.

C OLOR S PACE — Allows you to select the color space. The options are: RGB,

YCbCr, and YPbPr.

NOTE: If you adjust the settings for Color Temperature, RGB Color Adjust, and

White Intensity the projector automatically switch to Custom mode.

I MAGE S ETTINGS ( IN V IDEO M ODE )— Select and press to activate image settings.

The image settings menu provides the following options:

Using Your Projector 41

C OLOR T EMPERATURE — Allows you to adjust the color temperature. The screen appears cooler at higher color temperatures and warmer at lower color temperatures. When you adjust the values in the Color Adjust menu, the Custom mode is activated. The values are saved in the Custom mode.

RGB C OLOR A DJUST — Allows you to manually adjust the colors red, green, and blue.

S ATURATION — Allows you to adjust the video source from black and white to fully saturated color. Press to increase the amount of color in the image and to decrease the amount of color in the image.

S HARPNESS — Press to increase the sharpness and to decrease the sharpness.

T INT — Press to increase the amount of green in the image and to

W HITE I NTENSITY — Press and use and to display white intensity.

D YNAMIC A PERTURE — Allows you to set the projector dynamic aperture.

The options are: Off, Dynamic, and Auto.

C OLOR S PACE — Allows you to select the color space. The options are: RGB,

YCbCr, and YPbPr.

NOTE:

1 If you adjust the settings for Color Temperature, RGB Color Adjust,

Saturation, Sharpness, Tint, and White Intensity the projector automatically switch to Custom mode.

2 Saturation, Sharpness, and Tint are only available when the input source is from Component, Composite, or S-Video.

42 Using Your Projector

D ISPLAY S ETTINGS ( IN PC M ODE )— Select and press to activate display settings.

The display settings menu provides the following options:

H ORIZONTAL P OSITION — Press to move the image right and to move the image left.

V ERTICAL P OSITION — Press to move the image up and to move the image down.

F REQUENCY — Allows you to change the display data clock frequency to match the frequency of your computer’s graphics card. If you see a vertical flickering wave, use the Frequency control to minimize the bars. This is a coarse adjustment.

T RACKING — Synchronize the phase of the display signal with the graphic correct it. This is a fine adjustment. card. If you experience an unstable or flickering image, use Tracking to

A SPECT R ATIO — Allows you to select the aspect ratio to adjust how the image appears. Options are: Origin, 16:9, and 4:3.

•Origin — Select Origin to maintain the aspect ratio of the image projector according to the input source.

•16:9 — The input source scales to fit the width of the screen to project a

16:9 screen image.

•4:3 — The input source scales to fit the screen and projects a 4:3 image.

Z OOM — Press and to zoom and view the image.

Adjust the image scale by pressing or and press only. to view on your remote control

Z

OOM

N

AVIGATION Press to activate the Zoom Navigation menu.

Use to navigate the projection screen.

Using Your Projector 43

D ISPLAY S ETTINGS ( IN V IDEO M ODE )— Select and press to activate display settings. The display settings menu provides the following options:

A SPECT R ATIO — Allows you to select the aspect ratio to adjust how the image appears. Options are: Origin, 16:9, and 4:3. according to the input source.

•16:9 — The input source scales to fit the width of the screen to project a

16:9 screen image.

•4:3 — The input source scales to fit the screen and projects a 4:3 image.

Z OOM — Press and to zoom and view the image.

Adjust the image scale by pressing or and press only. to view on your remote control

Z

OOM

N

AVIGATION Press to activate the Zoom Navigation menu.

Use to navigate the projection screen.

44 Using Your Projector

P ROJECTOR S ETTINGS — Select and press to activate projector settings. The projector settings menu provides the following options:

A UTO S OURCE — Select Off (the default) to lock the current input signal. If input signals. If you press the Source button when the projector is on, it automatically finds the next available input signal. you press the Source button when the Auto Source mode is set to Off, you can manually select the input signal. Select On to auto detect the available

A UTO K EYSTONE — Select On to automatically adjust image distortion caused by tilting the projector.

H ORIZONTAL K EYSTONE — Use keystone.

V ERTICAL K EYSTONE — Use keystone.

and to adjust the image horizontal

and to adjust the image vertical

P ROJECTOR M ODE — Allows you to select the projector mode, depending upon how the projector is mounted.

•Rear Projection-Desktop — The projector reverses the image so that you can project from behind a translucent screen.

•Rear Projection-Ceiling Mount — The projector reverses and turns the image upside down. You can project from behind a translucent screen with a ceiling-mounted projection.

•Front Projection-Desktop — This is the default option.

•Front Projection-Ceiling Mount — The projector turns the image upside down for ceiling-mounted projection.

S PEAKER — Select On to enable the speaker. Select Off to the disable speaker.

C LOSED C APTION — Select On to enable close caption and activate the

CC2, CC3, and CC4. closed caption menu. Select appropriate closed caption options: CC1,

Using Your Projector 45

NOTE:

1 Closed caption option is available for NTSC only.

2 Closed captioning can only be enabled via S-Video and Composite Video inputs.

T EST P ATTERN — Test Pattern is used to test focus and resolution.

You can enable or disable the Test Pattern by selecting Off, 1, or 2. You can also invoke the Test Pattern 1 by pressing and holding down and buttons on the control panel simultaneously for 2 seconds. You can also invoke the test pattern 2 by pressing and holding down and buttons on the control panel simultaneously for 2 seconds.

Test Pattern 1:

Test Pattern 2:

F ACTORY R ESET — Select and press to reset all settings to its factory default. The below warning message appears:

Reset items include both computer sources and Video source settings.

46 Using Your Projector

LAN S ETTINGS — Select and press to activate LAN settings. The LAN settings menu provides the following options:

W IRELESS AND LAN— Select Enabled to active the Wireless and LAN function.

DHCP— If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired when you select

DHCP On. If DHCP is Off, manually set the IP Address, Subnet Mask, and Gateway. Use and and to set the next item.

to select the number of IP address, Subnet

IP A DDRESS — Automatically or manually assigns the IP address to the projector connected to the network.

S UBNET M ASK — Configure the Subnet Mask of the network connection.

G ATEWAY — Check the Gateway address with your network/system administrator if you configure it manually.

DNS— Check the DNS Server IP address with your network/system administrator if you configure it manually.

S TORE — Press to save the changes made in network configuration settings.

NOTE:

1. Use and buttons to select IP Address, Subnet Mask,

Gateway, DNS, and Store.

2. Press the button to enter IP Address, Subnet Mask, Gateway, or

DNS to set the value. (The selected option is highlighted in blue) a Use and buttons to select the option. b Use and buttons to set the value. c After the setup is complete, press the button to exit.

Using Your Projector 47

3. After the IP Address, Subnet Mask, Gateway, and DNS is set up, select Store and press button to store the settings.

4. If you select Store without pressing the Enter button, the system will keep the original settings.

R ESET — Press to reset network configuration.

W IRELESS S ETTINGS — Select and press to activate wireless settings. The wireless settings menu provides the following options:

48

W IRELESS — Default option is Connected. Select Disconnected to disable the wireless connection.

NOTE: It is recommended to use the default settings for Wireless

Connect.

DHCP S ERVER — Allows you to enable DHCP server of the wireless.

S TART IP A DDRESS — Automatically or manually assigns the Start IP address of the DHCP server to the projector connected to the wireless.

E ND IP A DDRESS — Automatically or manually assigns the End IP address of the DHCP server to the projector connected to the wireless.

S UBNET M ASK — Configure the Subnet Mask of the wireless connection.

G ATEWAY — Check the Gateway address with your network/system administrator if you configure it manually.

DNS— Check the DNS Server IP address with your network/system administrator if you configure it manually.

S TORE — Press to save the changes made in wireless configuration settings.

NOTE:

1. Use and buttons to select IP Address, Subnet Mask,

Gateway, DNS, and Store.

2. Press the button to enter IP Address, Subnet Mask, Gateway, or

DNS to set the value. (The selected option is highlighted in blue)

Using Your Projector

a Use and buttons to select the option. b Use and buttons to set the value. c After the setup is complete, press the button to exit.

3. After the IP Address, Subnet Mask, Gateway, and DNS is set up, select Store and press button to store the settings.

4. If you select Store without pressing the Enter button, the system will keep the original settings.

R ESET — Press to reset wireless configuration.

M ENU S ETTINGS — Select and press to activate the menu settings. The menu settings consists of the following options:

M ENU P OSITION — Allows you to change the position of the OSD menu on the screen.

M ENU T IMEOUT — Allows you to adjust the time for an OSD timeout. By default, the OSD disappears after 20 seconds of non-activity.

M ENU L OCK — Select On to enable the Menu Lock and hide the OSD on the control panel or remote control for 15 seconds, and then disable the function. menu. Select Off to disable the Menu Lock. If you want to disable the

Menu Lock function and have the OSD disappear, press the Menu button

M ENU T RANSPARENCY — Select to change the transparency level of the OSD background.

P ASSWORD — When Password Protect is enabled, a Password Protect screen requesting you to enter a password will be displayed when the power plug is inserted into the electrical output and the power for the projector is first turned on. By default, this function is disabled. You can enable this feature by selecting Enabled. If the password has been set before, key in the password first and select the function. This password security feature will

Using Your Projector 49

be activated the next time you turn on the projector. If you enable this feature, you will be asked to enter the projector’s password after you turn on the projector:

1 First time password input request:

a Go to Menu Settings, press and then select Password to Enabled the password settings.

b Enabling the Password function will pop up a change screen. Key in a

4-digit number from the screen and press .

c To confirm, enter the password again.

d If the password verification is successful, you may resume with accessing the projector's functions and its utilities.

2 If you have entered an incorrect password, you will be given another two chances. After three invalid attempts, the projector will automatically turn off.

NOTE: If you forget your password, contact DELL™ or a qualified service personnel.

3 To disable the password function, select the Disabled option to close the function.

4 To delete the password, select the Deleted option.

50 Using Your Projector

C HANGE P ASSWORD Key in the original password. Then, enter the new password and confirm the new password again.

P OWER S ETTINGS — Select and press to activate power settings. The power settings menu provides the following options:

Using Your Projector 51

Q UICK S HUTDOWN Select On to turn off the projector with a single press of the Power button. This function allows the projector to quickly power off with an accelerated fan speed. Slightly higher acoustic noise is expected during quick power off.

NOTE: Before you turn on the projector again, wait for 60 seconds to allow the internal temperature to stabilize. The projector will take a longer time to turn on if you try to power on immediately. Its cooling fan will run at full speed for about 30 seconds to stabilize the internal temperature.

P

OWER

S

AVING Select Off to disable Power Saving mode. By default, the projector is set to enter power saving mode after 120 minutes of no activity.

A warning message appears on screen showing a 60 seconds countdown before switching to power saving mode. Press any button during the countdown period to stop the power-saving mode.

You can also set a different delay period to enter power saving mode. The delay period is the time you want the projector to wait without an input signal. Power saving can be set to 30, 60, 90, or 120 minutes.

If an input signal is not detected during the delay period, the projector turns off. To turn on the projector press the Power button.

W

IRELESS Select Always On or Off when Standby to set the Wireless/LAN module on/off while the projector is standby status.

VGA O

UTPUT Select Always On or Off when Standby the VGA output feature at projector standby status.

L

AMP

M

ODE Allows you to select between Normal or ECO mode.

Normal mode operates at full power level. ECO mode operates at a lower power level which may provide longer lamp life, quieter operation, and dimmer luminance output on the screen.

L

AMP

H

OUR

R

ESET Press and select the Confirm option to reset the lamp hour.

52 Using Your Projector

PIP S ETTINGS — Select and press to activate pip settings. The pip settings menu provides the following options:

P

ICTURE

I

N

P

ICTURE Select On to enable the picture in picture display.

Select Off to disable the feature.

S

ECOND

S

OURCE Allows you to select the possible second source is available in the OSD selection depending on the current primary input source. See

"PIP Combination Sources" on page 113.

S

WAP Press to swapping the first and second source displays.

S

IZE Allows you to adjust the image size of the second source. The options are: Small, Mid, Large, and Half.

L

AYOUT Allows you to change the second source position to the four different corners. The options are: Top Left, Top Right, Bottom Left, and

Bottom Right.

I NFORMATION — The information menu displays the current projector settings.

Using Your Projector 53

LANGUAGE

Allows you to set the language for the OSD. Press to activate the Language menu.

HELP

If you encounter problems with your projector, you can access the help menu for troubleshooting.

54 Using Your Projector

Wireless Networking Installation

NOTE: Your computer must have the following minimum system requirements:

Operating System:

• Windows

Microsoft Windows XP™ Home or Professional Service pack 2 (32-bit

32-bit or 64-bit recommended), Windows Vista 32-bit, and Windows ® 7 Home or Professional

• MAC

MacBook and above, MacOS 10.5 and above

Minimum Hardware: a Intel Dual Core 1.8 MHz or higher b 256 MB of RAM required, 512 MB or more recommended c 10 MB of available hard-disk space d nViDIA or ATI graphic card must with 64 MB VRAM or above e Ethernet adapter (10 / 100 bps) for an Ethernet connection f A supported WLAN adapter for a WLAN connection (any NDIS-compliant

802.11b or 802.11g or 802.11n WiFi device)

Web browser

Microsoft Internet Explorer 6.0 or 7.0 (recommended) or 8.0, Firefox 2.0, Safari

3.0, and above

Using Your Projector 55

Enable Wireless on the Projector

In order to use your projector wirelessly, you need to complete the steps below:

1 Install the optional wireless dongle. See "Installing the Optional Wireless

Dongle" on page 11.

2 Connect the power cable to the wall outlet and press the power button.

3 Press the Menu button on your projector control panel or remote control.

NOTE: Use , , and buttons to navigate and to select.

4 The wireless connection default is Enabled. See "Wireless Settings" on page 48.

5 Access the INPUT SOURCE menu, select Wireless/USB and then select

Wireless Display on the sub-menu. See "INPUT SOURCE WIRELESS/USB" on page 38.

56 Using Your Projector

The Wireless Guide Screen shown below appears:

NOTE: If wireless connection is disabled, then follow these steps to set up:

ADVANCED SETTINGS J Wireless Settings J Wireless J Connected. The image input source will be automatically switched to wireless screen when wireless option is selected in this step.

6 Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP

ADDRESS. You will need these information to log in later.

Using Your Projector 57

Install the Wireless Application Software on Your Computer

7 Connect your computer to the 7700FullHD wireless network.

NOTE:

• Your computer must have wireless network function to detect the connection.

• When you connect to the 7700FullHD wireless network, you will lose wireless connectivity with other wireless networks.

NOTE: Remember to turn off all proxies. (In Microsoft ® Windows Vista: Click

Control Panel J Internet Options J Connections J LAN Settings)

7700FullHD Web Management web page.

58 Using Your Projector

NOTE: If the web page does not load automatically, enter the IP address

(default IP address is 192.168.100.10) noted from the projector’s screen in the browser’s address bar.

9 The 7700FullHD Web Management page opens. For first time use, click

Download.

10 Select the appropriate operating system, then click Download.

Using Your Projector 59

11 Click Run to proceed with the one-time installation of the software.

NOTE: You may choose to save the file and install it at a latter time. To do this, click

Save.

NOTE: If you are unable to install the application because of inadequate rights on the computer, please contact your network administrator.

12 The installation software will launch. Follow the on-screen instructions to complete setup.

60 Using Your Projector

Launch the Wireless Application

Once the installation is complete, the program will launch and search automatically. If the program not launch automatically, you can double-click the icon on the desktop to start the application. Select the Dell 7700FullHD,

Login

To communicate with your projector, enter the Login Code provided in Step 6 of

Wireless Networking Installation, then click OK.

NOTE: If the IP Address is not detected, enter the IP Address displayed at the bottom left corner of the screen.

Using Your Projector 61

Understanding the Buttons

After a successful log in, the following screen appears:

Projection Mode

1

2

3

4

Item Description

1 Status Bar

Menu

Displays IP and LOGIN CODE information.

Click to activate the application menu.

Minimize button Click to minimize the application.

Close button Click to exit the application.

2 Status Mode

Projection Mode Click to activate the projection mode.

Video Mode

3 Controls Toolbar

Click to activate the video mode.

Full screen

Split 1

Split 2

Split 3

Split 4

Click to project the image in full screen.

Click to project the image in the upper left corner of the screen.

Click to project the image in the upper right corner of the screen. corner of the screen.

Click to project the image in the lower right corner of the screen.

Stop

Pause

Click to stop projection.

Click to pause projection.

Audio Projection Click to enable audio projection.

4 Connection Status

Connection Icon Blinks when projection is in progress.

62 Using Your Projector

Projecting the Presentation

• To project the presentation, click any of the projection buttons

• To pause the presentation, click . The icon turns green.

• To continue the presentation, click again.

• To audio projection the presentation, click

. See "Audio Projection

Installation" on page 71.

• To stop the presentation, click .

.

Video Mode

1

Item

1 Control Toolbar

Open

Description

Play

Stop

Mute

Click to open folder and searching the video or music file.

Click to starting player.

Click to stop player.

Click to mute/un-mute.

NOTE: The following information is for wireless data presentation mode only. or animation. Refer to the frame-rate table below for reference:

Image display could be slow or not displayed smoothly if displaying a video clip

Frame Rate of Wireless Presentation

Screen Variation % 1

<5 %

<10%

<20%

<40%

<75%

<=100%

Estimated frames per second 2

30 3

28 3

26 3

25 3

22 3

20 3

Using Your Projector 63

NOTE:

1 The percentage of screen variation is based on 1024 x 768. Example to display a

320 x 240 video clip on 1024 x 768 desktop, the screen variation is 9.8%.

2 Actual frame rate could be different depending on factors such as network environment, image content, signal conditions, locations, and CPU performance.

3 Under clean WLAN environment using 802.11g connection, and no screen stretching.

4 Compressed to 1024 x 768 and under 802.11g.

NOTE: Your computer will not enter S1 (standby mode) / S3 (sleep mode) / S4 presentation.

(hibernate mode) when running a wireless, USB Display, or USB Viewer

Using the Menu

Click to display the menu.

W

EB

M

ANAGEMENT

Click to open the Web Management page. See "Managing the

Projector From Web Management" on page 78.

S EARCH FOR P ROJECTOR — Click to search and connect to wireless projector.

M AKE A PPLICATION T OKEN —

Click to make application token. See "Make

Application Token" on page 99.

I NFO — Click to display system information.

H OTKEY — Click to display the hotkey information.

A BOUT — Click to display the application version.

E XIT — Click to close the application.

64 Using Your Projector

Presentation to Go (PtG) Installation

Minimum system requirements to install PtG are as follow:

Operating System:

- Windows

Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit recommended), Windows Vista 32-bit, or Windows ®

32-bit or 64-bit

7 Home or Professional

- Office 2003 or Office 2007

In order to use your USB Viewer, you need to complete the steps below:

"Wireless and LAN" option and "Wireless connection" default are enabled.

1 Plug the USB Flash drive to your projector.

NOTE:

• Supports only the JPEG format photo within 10 MB x 40 M pixels.

• The PtG converter can convert your PowerPoint files into PtG files. See

"Install the PtG Converter Application Software on Your Computer" on page 69.

• You can download the "PtG Converter - Lite" from the Dell Support site at support.dell.com.

2 At INPUT SOURCE menu, select Wireless/USB and then select USB Viewer

on the sub-menu. See "INPUT SOURCE WIRELESS/USB" on page 38.

NOTE:

1

2

When the Wireless and LAN function is disabled , Go to LAN Settings menu, select the "Enabled" in the "Wireless and LAN" option to activate the Wireless and LAN function.

When the Wireless connection is disconnected, Go to Wireless Settings menu, select the "Connected" in the Wireless option to enable wireless connection.

Using Your Projector 65

PtG Viewer

System will stay in this page when ready.

Photo Viewer

66 Using Your Projector

PtG/Photo Function Introduction

Show valid PtG and Photo files which are stored in the USB disk.

NOTE: If only one disk is detected, the system will skip this step.

PtG Overview

Using Your Projector 67

Photo Overview

NOTE: Supports 14 languages of photo files name format (Languages: English,

Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian,

Simplified Chinese, Spanish, Swedish, and Traditional Chinese).

Buttons-Introduction

Use the up, down, and left buttons to navigate and button on your projector's control panel or remote control to select.

Button Up Down Left Right Enter

No function Enter PtG function Up Down Back

PtG Playback Pre Page Next Page Back

Photo function

Up Down Back

No function Next Pause

No function Enter

Photo

Playback

Pre Page Next Page Back No function No function

NOTE: If you enter the OSD menu while using PtG, PtG navigation by the up, down, and left buttons will not function.

68 Using Your Projector

Install the PtG Converter Application Software on Your Computer

Please follow the on-screen instructions to complete the setup.

NOTE: You can download the "PtG Converter - Lite" from the Dell Support site at support.dell.com.

Using Your Projector 69

Using the PtG Converter

1 Launch the "PtG Converter - Lite.exe" or double-click the desktop to start the application.

icon on the

2 Click to select a PowerPoint file and start conversion.

3 Click Browse button to select the storage location and then press OK.

NOTE:

1 If your computer does not have MS PowerPoint installed, file convert will fail.

2 PtG converter only supports up to 20 pages.

3 PtG converter only supports conversion of .ppt files to .PtG files.

70 Using Your Projector

Audio Projection Installation

Audio Projection only supports the Wireless Display and LAN Display input source.

Minimum system requirements as follow:

Operating System:

• Windows

Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit recommended), Windows Vista 32-bit, or Windows ®

Professional 32-bit or 64-bit

7 Home or

• MAC

MacBook Pro and above, MacOS 10.5 and above

Minimum Hardware:

a Intel ® Core™ i5-460 MHz (2.53 GHz/Turbo 2.8 GHz) or greater

b 1 GB DDR3 VRAM independent graphics card or more recommended

c 2 GB dual channel DDR3 SDRAM memory at 1066 MHz required or more recommended

d Gigabit Ethernet

e Integrated 802.11 b/g/n Wi-Fi Device for a WLAN connection

NOTE: If your computer does not meet the minimum hardware requirements, audio projection may have lag or noise. Meet the recommended system requirements to have optimized performance of audio projection.

NOTE: If you want to use wireless for audio projection, need installed the

optional wireless dongle. See "Installing the Optional Wireless Dongle" on page 11.

NOTE: The audio projector function needs an extra driver to be installed. A pop-up screen will alert you if your computer needs to install the driver. You can download the Audio Projection Driver from the Dell Support site at support.dell.com.

NOTE: Ports / Protocol for connection to the projector for projection via

Ethernet:

UDP: 1047,

TCP: 3268, 515, 1688, 1041

(backup: 1048, 1049)

(backup: 389, 8080, 21)

Using Your Projector 71

Enable Wireless or LAN on the Projector

1 Connect the power cable and turn on the projector by pressing the power button.

2.1 If the LAN is used for audio projection, follow these steps to enable Wireless and LAN function (default is Enabled): Advanced Settings LAN Settings

Wireless and LAN Enabled.

2.2 If the Wireless is used for audio projection, follow these steps to enable wireless connection (default is Connected): Advanced Settings Wireless Settings

Wireless Connected.

72 Using Your Projector

3 Access the Input Source menu, select the Wireless/USB and then select the

Wireless Display on the sub-menu.

The Wireless Guide Screen shown below appears:

4 Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP

ADDRESS. You will need these information to log in later.

Install the Wireless Application Software on Your Computer

5 "Wireless Application Software" is required if the Wireless or LAN is used for the Audio Projection set-up. Please download and install the software the first

NOTE: You only need to install the "Wireless Application Software" once.

6 Wireless Application Software download and install steps refer to steps 7 to 12

of the "Wireless Networking Installation" on page 55.

Using Your Projector 73

NOTE: If the LAN is used for audio projection, connect the LAN cable to the projector and the computer.

Launch the Wireless Application

7 Once the installation is complete, the program will launch automatically. Or you can double-click the icon on the desktop to start the application.

NOTE:

1 When you select the LAN for projection, click "Skip".

2 When you select the Wireless for projection, select the Dell 7700FullHD, and the click "OK".

74 Using Your Projector

Login

8 To communicate with your projector, enter the Login Code (see Step 4), and then click OK.

NOTE: If the IP Address is not detected, enter the IP Address displayed at the bottom left corner of the wireless screen.

9 You are now logged into the 7700FullHD Wireless Application. Click the "Play" button in the application to starting the LAN or wireless projection.

NOTE: You may use the controls to either project in full screen mode or in split screen mode.

10 Click the "Audio Projection" button in the application to enable Audio

Projection function.

NOTE: Audio projector function need install extra driver, if your computer do not install driver, will pop-up need install driver message on screen. You can download the "extra driver" from the Dell Support site at support.dell.com.

11 Executing the Windows Media Player or others audio player software

(example: Winamp player...) on your computer.

Using Your Projector 75

Video Stream Installation

Video Stream only supports the Wireless Display and LAN Display input source.

Minimum system requirements as follow:

Operating System:

• Windows

Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit recommended), Windows Vista™ 32-bit, or Windows ®

Professional 32-bit or 64-bit

7 Home or

• MAC

MacBook Pro and above, MacOS 10.5 and above

Minimum Hardware:

a Dual ® Core™ 1.8 GHz or greater

b 64 MB VRAM independent graphics card or more recommended

c 2 GB DDR SDRAM memory or more recommended

d Gigabit Ethernet

e Integrated 802.11 b/g/n Wi-Fi Device for a WLAN connection

NOTE: If your computer does not meet the minimum hardware requirements, have optimized performance of the video stream. video stream may have lag. Meet the recommended system requirements to

NOTE: If you want to use wireless feature, need installed the optional wireless

dongle. See "Installing the Optional Wireless Dongle" on page 11.

NOTE: Ports / Protocol for connection to the projector for projection via

Ethernet:

UDP: 1047,

TCP: 3268, 515, 1688, 1041

(backup: 1048, 1049)

(backup: 389, 8080, 21)

Video Stream Support Format

File Format Video Format Max Resolution

MP4, MOV H.263

Audio Format

FWVGA (854x480) AAC LC, LPCM

MP4, MOV H.264

MP4, MOV MPEG-4

ASF

Up to 720P30

Up to 720P30

WMV9/VC-1 Up to 720P24

AAC LC, LPCM, MP3

AAC LC, LPCM, MP3

WMA

76 Using Your Projector

Enable Wireless or LAN on the Projector

Please refer to "steps 1 to 4 of the Audio Projection Installation" on page 71 for

instructions to enable wireless or LAN feature.

Install the Wireless Application Software on Your Computer

Please refer to "steps 5 to 6 of the Audio Projection Installation" on page 73 for

instructions to install the Dell Wireless Application Software.

Launch the Wireless Application

Please refer to "step 7 of the Audio Projection Installation" on page 74 for

instructions to launching the application..

Login

Please refer to "step 8 of the Audio Projection Installation" on page 75 for

instructions to log-in the application.

1 You are now logged into the 7700FullHD Wireless Application. Click

"Video Mode" button switch to Video Mode screen.

2 Click to select the video or music files and starting player.

NOTE: Select the video or music file, then press Play. The projector will enter hibernate mode first, it will playback the video or music file after a few seconds.

Using Your Projector 77

Managing the Projector From Web

Management

Configuring the Network Setting

If the projector is connected to a network, you can access the projector using a web

browser. For configuring the network setting, refer to "LAN Settings" on page 47.

Accessing Web Management

Use Internet Explorer 6.0 and above or Firefox 2.0 and above and enter the IP address. You can now access Web Management and manage the projector from a remote location.

Home Page

• Access the Web Management Home page by entering the projector’s IP

address at the web browser. See "LAN Settings" on page 47.

• Select the language for web management from the list.

• Click any menu item on the left tab to access the page.

78 Using Your Projector

Download the Wireless Application Software

See also "Wireless Networking Installation" on page 55.

Click the Download button of the corresponding operating system of your computer.

Using Your Projector 79

Conference Control

This allows you to host conference presentations from different sources without using projector cables and lets you control how each presentation will appear on screen.

NOTE: Without Conference Play Control, the last user to hit the "Play" button on the application will take control of the full-screen projection.

Computer Name: Lists the computers logged for conference control.

Play Control: Click the buttons to control how each computer’s projection will appear on screen.

• Full screen projection — The presentation from the computer occupies the whole screen.

Split 1 - The presenation from the computer appears on the upper left corner of the screen.

Split 2- The presenation from the computer appears on the upper right corner of the screen.

Split 3- The presenation from the computer appears on the lower left corner of the screen.

Split 4- The presenation from the computer appears on the lower right corner of the screen.

• Stop - Projection from the computer is stopped.

IP Address: Shows each computer’s IP Address.

NOTE: To end the conference, click Home.

80 Using Your Projector

Managing Properties

Admin

An administrator password is required to access the Admin page.

Admin Password: Enter the administrator password and then click Login.

The default password is "admin". To change the password, see "Change

Passwords" on page 86.

Using Your Projector 81

System Status

Displays the Network Status, Connection Status, and Projector Status information.

82 Using Your Projector

Network Setup

See OSD section on page 47.

IP Setup projector automatically, or Use the following IP address to assign an IP address manually.

DHCP Server Setup

Default Gateway, and DNS Server address from a DHCP server, or Disable to disable this function.

Wireless Setup

Encryption, and Key. Choose Disable to disable the wireless set up.

Using Your Projector 83

SSID: Up to maximum length of 32 characters.

Encryption: You can Disable WPA key or select one of 64-bit or 128-bit in

ASCII or HEX string.

Key: If Encryption is enabled, you have to set key value according to the encryption mode you selected.

RADIUS Server Setup

• Set up the IP address, Port, and Key information.

GateKeeper

• There are three options:

All Pass: Allow users to access the office network via the wireless projector.

All Block: Block users from accessing the office network via the wireless projector.

Internet Only: Block users from the office network, but still reserve Internet connection capability.

Set Security For SNMP

• Setup Write Community information.

Click the Apply button to save and apply changes. The projector must be restarted for the changes to take effect.

84 Using Your Projector

Projection Setup

Projection Setup

Resolution: Allows you to select the resolution. Options are: XGA (1024 x

768) and 720p (1280 x 720).

Login Code: Select how you want the login code to be generated by the projector. There are three options:

Disable: Login code will not be required when logging in to the system.

Random: Default is Random. Login code will be randomly generated.

Use the following code: Enter a 4-digit code. This code will be used to log in to the system.

Projector Setup

• Set up the Model Name, Projector Name, Location, and Contact information (up to 21 characters for each field).

Click the Apply button to save and apply changes. The projector must be restarted for the changes to take effect.

Using Your Projector 85

Change Passwords

This page allows you to change the administrator password.

Enter New Password: Enter the new password.

Confirm New Password: Enter the password again and click Apply.

NOTE: Contact Dell if you forget your administrator password.

86 Using Your Projector

Reset to Default

Click the Apply button to restore the wireless/network setup to its factory default settings.

Using Your Projector 87

Firmware Upgrade

Use the Firmware Upgrade page to update your projector’s wireless firmware.

NOTE: Please disable and enable wireless/network using the OSD to restart the network card for the projector after firmware upgrade is successful.

To start the firmware update, follow these steps:

1 Press Browse to select the file to update.

2 Click the Update button to start. Wait while the system updates the firmware in your device.

CAUTION: Do not interrupt the update process as this may cause the system to crash!

3 Click OK when the update is complete.

88 Using Your Projector

Projector Upgrade

Use the Projector Upgrade page to update your projector’s firmware.

NOTE: Please disable and enable wireless/network using the OSD to restart the network card for the projector after firmware upgrade is successful.

NOTE: Ensure the wireless standby mode is turn on (default is off), follow these steps: Advanced Settings -> Power Settings -> Wireless -> Always On.

To start the firmware update, follow these steps:

1 Plug in the power cord and the projector will enter standby mode.

2 Connect the LAN cable to the projector and your computer.

3 Open your Internet browser and then enter the IP address (default IP address is

192.168.100.10).

4 At Projector Upgrade web page, press Browse to select the file to update.

Using Your Projector 89

5 Click the Update button to start. Wait while the system updates the firmware in your device.

NOTE: Temp and Lamp LEDs are both lighted up (Amber).

CAUTION: Do not interrupt the update process as this may cause the system to crash!

6 Click OK when the update is complete.

90 Using Your Projector

Projector Control Panel

Projector Information

Projector Status: There are five status: Lamp On, Standby, Power Saving,

Cooling, and Warming up. Click Refresh to refresh the status and control settings.

Power Saving: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. For

more information, see "Power Saving" on page 52.

Alert Status: There are three alert states: Lamp warning, Low lamp life, and

Temperature warning. Your projector might lock up in the protection mode if any of the alerts are activated. To exit the protection mode, click Clear to

Using Your Projector 91

Image Control

Operation Mode: Allows you to select the operation mode. The two options are: Normal Mode and ECO Mode.

Projector Mode: Allows you to select the projector mode, depending on how the projector is mounted. There are four projection modes: Front

Projection-Desktop, Front Projection-Ceiling Mount, Rear Projection-

Desktop, and Rear Projection-Ceiling Mount.

Source Select: The Source Select menu allows you to select your projector input source. You can select VGA-A, VGA-B, S-Video, Composite Video,

HDMI-A, HDMI-B, RCA Component, Wireless Display, USB Display, or

USB Viewer.

Video Mode: Select a mode to optimize the display image based on how the projector is being used:

Bright: Maximum brightness and contrast.

- Movie: For viewing movies and photos

- sRGB: Provides a more accurate color representation.

Custom: User-preferred settings.

Blank Screen: You can select On or Off.

Aspect Ratio: Allows you to select the aspect ratio to adjust how the image appears.

Brightness: Select value to adjust the brightness of the image.

Contrast: Select value to adjust the display contrast.

Click the Auto Adjust button to adjust the settings automatically.

Audio Control

Audio Input: Select the input source. Options are: Analog In, HDMI-A,

HDMI-B, and Wireless/LAN.

Volume: Select the value (0~20) for audio volume.

Speaker: Select On to enable the audio function or select Off to disable the audio function.

Click the Factory Reset button to restore the factory default settings.

92 Using Your Projector

Alert Setting

E-mail Alert

E-mail Alert: You can set whether to be notified by email (Enable) or not

(Disable).

To/Cc/From: You can enter email address of sender (From) and recipients

(To/Cc) to receive notification when an abnormality or warning occurs.

Subject: You can enter the subject line of the email.

Click the E-mail Alert Test button to test the e-mail alert settings.

SMTP Setting

Out going SMTP server, User name, and Password should be provided by your network administrator or MIS.

Alert Condition

• You can select the abnormalities or warnings to be notified by email. When any of the alert conditions occur, an email will be sent to the recipients

(To/Cc).

Click the Save button to save the settings.

NOTE: E-mail alert is designed to work with a standard SMTP server using the default 25 port. It does not support encryption and authentication (SSL or TLS).

Using Your Projector 93

Reboot System

Click Reboot to reboot the system.

Crestron

For Crestron function.

94 Using Your Projector

FAQS:

I would like to remotely access the projector via the Internet.

What is the best setting for the browser?

To have the best setting for the browser, please follow the below steps:

1 Open Control Panel Internet Options

General tab Temporary Internet Files

Settings Select Every visit to the pages.

2 Some firewall or anti-virus may block the

HTTP application. If possible, turn off the firewall or anti-virus.

I would like to remotely access The following are the TCP/IP socket ports the projector via Internet. What which the projector uses. socket port number should I

UDP/TCP Port

Number

Description

TCP 80

UDP/TCP 25

Web configuration

(HTTP)

SMTP: used for email routing between mail servers

UDP/TCP 161

UDP 9131

SNMP: Simple

Network

Management

Protocol

AMX: used for AMX discovery

Why am I unable to access the projector via the Internet?

1 Check whether your computer/laptop is connected to the Internet.

2 Check with your MIS or network administrator whether your computer/laptop is in the same subnet.

Using Your Projector 95

Why am I unable to access the

SMTP server?

1 Check with your MIS or network administrator whether the SMTP server function is open for the projector and the IP assigned to the projector is allowed to access the SMTP server. The projector’s SMTP socket port number is 25, this cannot be changed.

2 Check if the outgoing SMTP server, user name, and password are set correctly.

3 Some SMTP servers will check whether the mail address of "From" correlates with the

"User name" and "Password". For example, you use [email protected] as the mail address in

"From". You should also use [email protected] account information for the User name and the password to log in the SMTP server.

Why am I unable to receive the test alert email even though the projector already indicates the test mail is already sent?

It could be because the SMTP server recognized the alert mail as a spam mail or because of the SMTP server restriction. Check with your MIS or network administrator for the SMTP server’s setting.

96 Using Your Projector

Firewall Configuration and FAQ

Q: Why can’t I access the Web Management Page?

A: Your computer’s firewall configuration may prevent you from accessing the

Web Management Web Page. Please refer to the following configuration settings:

Firewall Protection Configuration

McAfee Security

Center

Norton AntiVirus

Sygate Personal

Firewall

1 Launch McAfee Security Center (Start > All

Programs > McAfee > McAfee Security Center).

2 On the personal firewall plus tab, click View the

Internet Applications List.

3 Find and select Dell 7700FullHD Projector from the list.

4 Right-click on its Permissions column.

5 Select Allow Full Access from the pop-up menu.

1 Open Norton AntiVirus (Start > All Programs >

Norton AntiVirus > Norton AntiVirus).

2 Click Options menu, then select Norton AntiVirus.

3 On the Status page, select Internet Worm

Protection.

4 Find and select Dell 7700FullHD Projector from the list of programs.

5 Right-click on its Internet Access column.

6 Select Permit All from the pop-up menu.

7 Click OK.

1 Open Sygate Personal Firewall (Start > All Programs

> Sygate > Sygate Personal Firewall).

2 From the Running Applications list, find and right-click on Dell 7700FullHD Projector.

3 Select Allow from the pop-up menu.

Using Your Projector 97

Firewall Protection Configuration

Windows Firewall 1 Open Windows Firewall (Start > All Programs >

Control Panel). Double-click on Windows Firewall.

2 On the General tab, uncheck Don’t allow

exceptions.

3 On the Exceptions tab, click the Add Program... button.

4 Find and select Dell 7700FullHD Projector from the list of programs, then click OK.

5 Click OK to confirm exceptions settings.

Zone Alarm 1 Open Zone Alarm Firewall (Start > All Programs >

Zone Labs > Zone Labs Center).

2 On the Program Control page, find and select

Dell 7700FullHD Projector from the list.

3 Right-click on its Access-Trusted column.

4 Select Allow from the pop-up menu.

5 Right-click and select Allow for the Access-Internet,

Server-Trusted, and Server-Internet columns.

98 Using Your Projector

Make Application Token

NOTE: This feature is only applicable to wireless-enabled models.

The Application Token lets you perform Plug and Show using a USB token.

1 From the application software, click > Make Application Token.

2 The following screen appears. Click Next.

3 Plug a flash drive into any of the USB ports on your computer. Select the drive from the list, then click Next.

Using Your Projector 99

4 Click Finish to close the wizard.

100 Using Your Projector

Troubleshooting Your Projector

4

If you experience problems with your projector, see the following troubleshooting

tips. If the problem persists, contact Dell™ (see Contacting Dell™ on page 115).

Problem

No image appears on the screen

F8

CRT/LCD

Fn

Possible Solution

• Ensure that the lens cap is removed and the projector is turned on.

• Ensure that you have chosen the correct input source on the INPUT SOURCE menu.

• Ensure the external graphics port is enabled.

If you are using a Dell™ laptop computer, press (Fn+F8). For other computers, see your respective documentation. If images are not displayed properly, please upgrade the video driver of your computer. For Dell computers, see support.dell.com.

• Ensure that all the cables are securely

on page 10. connected. See "Connecting Your Projector"

• Ensure that the pins of the connectors are not bent or broken.

• Ensure that the lamp is securely installed

(see "Changing the Lamp" on page 106).

• Use Test Pattern in the Projector Settings of the Advanced Settings menu. Ensure that the colors of the test pattern are correct.

Troubleshooting Your Projector 101

Problem (continued) Possible Solution (continued)

Partial, scrolling, or incorrectly displayed image

1 Press the Auto Adjust button on the remote control or the control panel.

2 If you are using a Dell™ portable computer, set the resolution of the computer to Full

HD (1920 x 1080): a Right-click the unused portion of your

Microsoft ® Windows ® desktop, click

Properties, and then select Settings tab. b Verify that the setting is 1920 x 1080 pixels for the external monitor port. c Press (Fn+F8).

If you experience difficulty in changing resolutions, or if your monitor freezes, restart all the equipment and the projector.

If you are not using a Dell™ portable computer, see your documentation. If images are not displayed properly, please upgrade the video driver of your computer. For a Dell computer, see support.dell.com.

The screen does not display If you are using a portable computer, press your presentation (Fn+F8).

Image is unstable or flickering Adjust the tracking in the OSD Display

Settings of the Advanced Settings menu (in

PC Mode only).

Image has vertical flickering Adjust the frequency in the OSD Display bar Settings of the Advanced Settings menu (in

PC Mode only).

Image color is incorrect • If the display receives the wrong signal output from the graphics card, please set the signal type to RGB in the OSD Image

Settings of the Advanced Settings tab.

• Use Test Pattern in the Projector Settings of the Advanced Settings menu. Ensure that the colors of the test pattern are correct.

102 Troubleshooting Your Projector

Problem (continued) Possible Solution (continued)

Image is out of focus

The image is stretched when displaying a 16:9 DVD

1 Adjust the focus ring on the projector lens.

2 Ensure that the projection screen is within the required distance from the projector

The projector automatically detects the input signal format. It will maintain the aspect ratio of the projected image according to input signal format with an Original setting.

If the image is still stretched, adjust the aspect ratio in the Display Settings of the Advanced

Settings menu in the OSD.

Image is reversed Select Projector Settings of the Advanced

Settings from the OSD and adjust the projector mode.

Lamp is burned out or makes When the lamp reaches its end of life, it may a popping sound burn out and may make a loud popping sound.

If this occurs, the projector does not turn back

on. To replace the lamp, see "Changing the

Lamp" on page 106.

LAMP light is solid amber If the LAMP light is solid amber, replace the lamp.

LAMP light is blinking amber If the LAMP light is blinking amber, the lamp module connection may be disrupted. Please check the lamp module and ensure that it is properly installed.

If the LAMP light and the Power light are blinking amber, the lamp driver has failed and the projector will automatically shut down.

If the LAMP and TEMP lights are blinking amber and the Power light is solid blue, the color wheel has failed and the projector will automatically shut down.

To clear the protection mode, press and hold the POWER button for 10 seconds.

Troubleshooting Your Projector 103

Problem (continued) Possible Solution (continued)

TEMP light is solid amber The projector has overheated. The display automatically shuts down. Turn the display on again after the projector cools down. If the problem persists, contact Dell™.

TEMP light is blinking amber If the projector fan fails, the projector will automatically shut down. Try to clear the projector mode by pressing and holding the

Power button for 10 seconds. Please wait for about 5 minutes and try to power up again. If the problem persists, contact Dell™.

The OSD does not appear on Try to press the Menu button on the panel for the screen 15 seconds to unlock the OSD. Check the

Menu Lock on page 49.

The remote control is not operating smoothly or works beam transmitted from the remote is too dim. only within a limited range

The battery may be low. Check if the laser

If so, replace with two new AAA batteries.

104 Troubleshooting Your Projector

Guiding Signals

Projector Status Description

Standby mode

Warming up mode

Lamp on

Projector in Standby mode. Ready to power on.

Projector takes some time to warm up and power on.

Projector in Normal mode, ready to display an image.

Note: The OSD menu is not accessed.

Projector is cooling to shutdown.

The projector takes 60 seconds to cool down before entering Power Saving mode.

Cooling mode

Cooling before

Power Saving mode

Projector overheated

Lamp driver overheated

Fan breakdown

Lamp driver breakdown

Color Wheel breakdown

Lamp failure

Fault - DC supply

(+12V)

Lamp module connection failed

Air vents might be blocked or ambient temperature may be above 35 ºC. The projector automatically shuts down. Ensure that the air vents are not blocked and that the ambient temperature is within operational range. If the problem persists, contact Dell.

The lamp driver is overheated. The air vents may be blocked. The projector automatically shuts down. Turn the display on again after the projector cools down. If the problem persists, contact Dell.

One of the fans has failed. The projector automatically shuts down. If the problem persists, contact Dell.

The lamp driver has failed. The projector automatically shuts down. Unplug the power cord after three minutes and then turn the display on again. If this problem persists, contact Dell.

Color wheel cannot start. The projector has failed and the projector automatically shuts down. Unplug the power cord after three minutes and then turn on the projector. If this problem persists, contact Dell.

Lamp is defective. Replace the lamp.

Power supply has been interrupted. The projector automatically shuts down.

Unplug the power cord after three minutes and then turn on the projector. If this problem persists, contact Dell.

Lamp module connection may be disrupted. Check the lamp module and ensure that it is properly installed. If the problem persists, contact Dell.

Control Buttons

Power

BLUE

Flashing

BLUE

BLUE

BLUE

AMBER

OFF

AMBER

ÒFF

AMBER

Flashing

BLUE

OFF

AMBER

Flashing

OFF

Indicator

TEMP

(Amber)

LAMP

(Amber)

OFF OFF

OFF OFF

OFF

OFF

OFF

OFF

OFF

OFF

AMBER

AMBER

AMBER

Flashing

OFF

AMBER

Flashing

OFF

AMBER

OFF

OFF

OFF

OFF

AMBER

Flashing

AMBER

Flashing

AMBER

AMBER

AMBER

Flashing

Troubleshooting Your Projector 105

Changing the Lamp

CAUTION: Before you begin any of the procedures in this section, follow the

Safety Instructions as described on page 8.

Replace the lamp when the message "Lamp is approaching the end of its useful life in the operation. Replacement suggested! www.dell.com/lamps" appears on the screen. If this problem persists after replacing the lamp, contact Dell™. For

more information, see Contacting Dell™on page 115.

CAUTION: Use an original lamp to ensure safe and optimal working condition of your projector.

CAUTION: The lamp becomes very hot when in use. Do not attempt to replace the lamp until the projector has been allowed to cool down for at least 30 minutes.

CAUTION: Do not touch the bulb or the lamp glass at any time. Projector lamps are very fragile and may shatter if touched. The shattered glass pieces are sharp and can cause injury.

CAUTION: If the lamp shatters, remove all broken pieces from the projector and dispose or recycle according to state, local, or federal law. For more information see www.dell.com/hg.

1 Turn off the projector and disconnect the power cord.

2 Let the projector cool for at least 30 minutes.

3 Loosen the two screws that secure the lamp cover, and remove the cover.

4 Loosen the two screws that secure the lamp.

5 Pull the lamp up by its metal handle.

NOTE: Dell™ may require lamps replaced under warranty to be returned to Dell™. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site.

6 Replace with the new lamp.

7 Tighten the two screws that secure the lamp.

8 Replace the lamp cover and tighten the two screws.

9 Reset the lamp usage time by selecting "Yes" for Lamp Hour Reset in the OSD

Power Settings of the Advanced Settings menu (see Power Settings of the

106 Troubleshooting Your Projector

Advanced Setting menu on page 51). When a new lamp module has been

changed, the projector will automatically detect and reset the lamp hours.

CAUTION: Lamp Disposal (for the US only)

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE

RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL

THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR

LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT

LAMP-SPECIFIC DISPOSAL INFORMATION, CHECK WWW.LAMPRECYCLE.ORG.

Troubleshooting Your Projector 107

5

Specifications

Light Valve

Brightness

Contrast Ratio

Uniformity

Number of Pixels

Aspect Ratio

Displayable Color

Color Wheel Speed

Projection Lens

Projection Screen Size

Projection Distance

Video Compatibility

Power Supply

0.95" 1080p DMD, DarkChip2™

5000 ANSI Lumens (Max.)

2500:1 (Natural)

10000:1 (Dynamic)

20000:1 (Static)

85% Typical (Japan Standard - JBMA)

1920 x 1080 (1080p)

16:9

1.07 billion colors (with Dithering)

2X

F-Stop: F/ 2.6~2.9

Focal length, f=39.12~46.94 mm

1.2X manual Zoom Lens

Throw ratio =1.85~2.22 wide and tele

Offset ratio: 115 ± 5%

20.3~292.9 inches (diagonal)

3.28~39.37 ft (1 m ~ 12 m)

Composite Video / S-Video: NTSC (J, M, 4.43), PAL

(B, D, G, H, I, M, N, Nc, 60), SECAM (B, D, G, K,

K1, L)

HDMI, and Component Video input (via VGA and

YPbPr RCA): 1080i/p, 720p, 576i/p, 480i/p

Universal AC 100-240 50-60 Hz with PFC input

108 Specifications

Power Consumption Normal mode: 525 W ± 10% @ 110 Vac

Eco mode: 430 W ± 10% @ 110 Vac

Power saving mode: <20 W (Wireless and

Network On)

Standby mode: < 0.5 W (Network, VGA_Out, and

Wireless Off)

2 speakers x 5 watt RMS Audio

Noise Level

Weight

39 dB(A) Normal mode, 36 dB(A) Eco mode

16 lb (7.26 kg)

Dimensions (W x H x D) 17.01 x 5.31 x 11.42 inches (432 x 135 x 290 mm)

17.01"(432 mm)

5.31"(135 mm)

Environmental

I/O Connectors

11.42"(290 mm)

Operating temperature: 5 o

Humidity: 80 % maximum

C - 35 o C (41 o F- 95 o F)

Storage temperature: 0 o C to 60 o C (32 o

Humidity: 90 % maximum

F to 140 o F)

Shipping temperature: -20 o

(-4 o F to 140 o F)

Humidity: 90 % maximum

C to 60 o C

Power: One AC power socket (3-pin - C14 inlet)

VGA input: Two 15-pin D-sub connectors (Blue),

VGA-A and VGA-B, for analog RGB/Component input signals.

VGA output: One 15-pin D-sub connector (Black) for VGA-A loop through.

Component Video input: One set of RCA connector

(RGB) for component input signal.

Specifications 109

Wireless Dongle

110 Specifications

S-Video input: One standard 4-pin min-DIN

S-Video connector for Y/C signal.

Composite Video input: One Yellow RCA jack for

CVBS signal.

HDMI input: Two HDMI connector for supporting

HDMI 1.3. HDCP compliant.

Analog Audio input: One 3.5 mm stereo mini phone jack (Blue).

Variable audio output: One 3.5 mm stereo mini phone jack (Green).

USB (type A) port: One USB connector for

Photo/PtG viewer (JPG/PPT format).

USB (type B) port: One mini USB slave for remote support and One USB connector for supporting

USB Display.

RS232 port: One 9-pin D-sub for RS232 communication.

RJ45 port: One RJ45 connector for control of projector through network and LAN Display.

12 V output: One 12 V DC / 200 mA max. relay output for driving automatic screen.

Wireless Standard: IEEE802.11b/g/n supporting wireless dongle (USB interface,

Optional).

OS environment: Windows 7/Vista/XP/2000, MAC

OS X

Support: Presentation slides and projector control.

Allow connection up to 30 users at the same time.

4-to-1 split screen. Allow four presentation slides to be projected on screen.

Conference Control mode.

Supports Audio Projection (need to install extra driver)

Supports Video Streaming (up to 720p)

Lamp Philips 400 W user-replaceable lamp (up to 2000 hours in eco mode; up to 1500 hours in normal mode)

NOTE: The lamp life rating for any projector is a measure of brightness degradation only, and is not a specification for the time it takes a lamp to fail and cease light output. Lamp life is defined as the time it takes for more than

50 percent of a lamp sample population to have brightness decrease by approximately 50 percent of the rated lumens for the specified lamp. The lamp life rating is not guaranteed in any way. The actual operating life span of a projector lamp will vary according to operating conditions and usage patterns.

Usage of a projector in stressful conditions which may include dusty environments, under high temperatures, many hours per day, and abrupt powering-off will most likely result in a lamp’s shortened operating life span or possible lamp failure.

Specifications 111

RS232 Pin Assignment

RS232 Protocol

• Communication Settings

Connection settings

Baud Rate

Data Bits

Parity

Stop Bits

Value

19,200

8

None

1

Command types

To pop up the OSD menu and adjust the settings.

Control command Syntax (From PC to Projector)

[H][AC][SoP][CRC][ID][SoM][COMMAND]

Example: Power ON Command (Send low byte firstly)

--> 0xBE, 0xEF, 0x10, 0x05, 0x00, 0xC6, 0xFF, 0x11, 0x11, 0x01, 0x00, 0x01

Control Commands List

To view the latest RS232 code, go to the Dell Support site at: support.dell.com.

112 Specifications

PIP Combination Sources

HDMI-A

HDMI-B

VGA-A

VGA-B

HDMI-A HDMI-B VGA-A VGA-B Component

No

No

Component

S-Video

Composite Yes

Wireless Display No

Yes

Yes

Yes

Yes

No

No

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

No

No

No

No

No

Yes

Yes

Yes

No

No

No

No

No

Yes

Yes

Yes

No

No

No

No

No

Yes

USB Display

USB Viewer

No

No

No

No

Yes

Yes

Yes

Yes

Yes

Yes

HDMI-A

HDMI-B

VGA-A

VGA-B

Component

S-Video

Composite No

Wireless Display Yes

No

No

No

No

S-Video Composite Wireless USB USB

Display Display Viewer

Yes

Yes

Yes

Yes

No

No

No

No

No

No

No

No

No

No

No

Yes

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

No

USB Display

USB Viewer

Yes

Yes

Yes

Yes

No

No

No

No

No

No

Specifications 113

Compatibility Modes (Analog/Digital)

Resolution

1920 x 1080 i60

1280 x 720

1024 x 768

1280 x 800

1366 x 768

1360 x 768

1024 x 768

1440 x 900

1152 x 864

1280 x 960

1280 x 1024

1152 x 864

1400 x 1050

1280 X 800

1280 x 1024

1440 X 900

640 x 350

640 x 480

640 x 480 p60

720 x 480 p60

720 x 576 p50

720 x 400

640 x 480

848 x 480

640 x 480

800 x 600

800 x 600

800 x 600

1024 x 768

1280 x 720 p50

1280 x 720 p60

1920 x 1080 i50

1680 x 1050

1280 x 960

1920 x 1080

1400 X 1050

1280 x 1024

1440 X 900

1600 x 1200

75.000

60.000

60.020

85.000

59.978

84.880

75.025

74.984

60.000

59.855

75.029

59.810

59.790

60.015

84.997

59.887

59.954

85.002

60.000

74.867

85.024

84.842

60.000

85.008

60.317

75.000

85.061

60.004

50.000

60.000

50.000

70.087

59.940

59.940

59.940

50.000

70.087

75.000

60.000

114 Specifications

Pixel Clock (MHz)

108.000

108.000

108.000

119.651

121.750

122.500

135.000

136.750

74.250

74.500

78.750

83.500

85.500

85.500

94.500

106.500

36.000

40.000

49.500

56.250

65.000

74.250

74.250

74.250

25.175

25.175

25.175

27.000

27.000

28.322

31.500

33.750

146.250

148.500

148.500

156.000

157.000

157.000

162.000

67.500

60.000

63.981

77.095

65.317

71.554

79.976

70.635

33.750

44.772

60.023

49.702

47.712

47.712

68.677

55.935

65.290

85.938

67.500

82.278

91.146

80.430

75.000

43.269

37.879

46.875

53.674

48.363

37.500

45.000

28.125

31.469

31.469

31.469

31.469

31.250

31.469

37.500

31.020

Contacting Dell

For customers in the United States, call 800-WWW-DELL (800-999­

3355).

NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.

Dell™ provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1

2

Visit support.dell.com. down menu at the bottom of the page.

3

4

5

Click Contact Us on the left side of the page.

Select the appropriate service or support link based on your need.

Choose the method of contacting Dell that is convenient for you.

Contacting Dell 115

Appendix: Glossary

ANSI L brightness) reading at the center of each rectangle, and averaging these nine points.

UMENS dividing a square meter image into nine equal rectangles, measuring the lux (or

A SPECT R ATIO The most popular aspect ratio is 4:3 (4 by 3). Early television and computer video formats are in a 4:3 aspect ratio, which means that the width of the image is 4/3 times the height.

Brightness — The amount of light emitted from a display or projection display or projection device. The brightness of projector is measured by ANSI lumens. temperature implies warmer (more yellow/red) light while high color temperature implies a colder (more blue) light. The standard unit for color temperature is

Kelvin (K).

Component Video — A method of delivering quality video in a format that consists of the luminance signal and two separate chrominance signals and are defined as Y'Pb'Pr' for analog component and Y'Cb'Cr' for digital component.

Component video is available on DVD players.

Composite Video — A video signal that combines the luma (brightness), chroma

(color), burst (color reference), and sync (horizontal and vertical synchronizing signals) into a signal waveform carried on a single wire pair. There are three kinds

Compressed Resolution — If the input images are of higher resolution than the native resolution of the projector, the resulting image will be scaled to fit the means that some image content is lost.

Contrast Ratio — Range of light and dark values in a picture, or the ratio between their maximum and minimum values. There are two methods used by the

1 Full On/Off — measures the ratio of the light output of an all white image (full on) and the light output of an all black (full off) image.

2 ANSI — measures a pattern of 16 alternating black and white rectangles. The average light output from the white rectangles is divided by the average light output of the black rectangles to determine the ANSI contrast ratio.

Full On/Off contrast is always a larger number than ANSI contrast for the same projector.

116 Glossary

dB — decibel — A unit used to express relative difference in power or intensity, usually between two acoustic or electric signals, equal to ten times the common logarithm of the ratio of the two levels.

Diagonal Screen — A method of measuring the size of a screen or a projected image. It measures from one corner to the opposite corner. A 9 ft high and 12 ft wide, screen has a diagonal of 15 ft. This document assumes that the diagonal dimensions are for the traditional 4:3 ratio of a computer image as per the example above.

DHCP — Dynamic Host Configuration Protocol — A network protocol that enables a server to automatically assign a TCP/IP address to a device.

DLP

® filter is sent to the DLP mirrors which arrange the RGB colors into a picture

Texas Instruments, using small manipulated mirrors. Light passing through a color projected onto screen, also known as DMD.

DMD — Digital Micro-Mirror Device — Each DMD consists of thousands of tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.

DNS — Domain Name System — An Internet service that translates domain names into IP addresses.

Focal Length — The distance from the surface of a lens to its focal point.

Frequency — It is the rate of repetition in cycles per seconds of electrical signals.

Measured in Hz (Hertz).

HDCP — High-Bandwidth Digital-Content Protection — A specification developed by Intel™ Corporation to protect digital entertainment across digital interface, such as DVI, HDMI.

HDMI — High-Definition Multimedia Interface — HDMI carries both uncompressed high definition video along with digital audio and device control data in a single connector.

Hz (Hertz) — Unit of frequency.

IEEE802.11 — A set of standards for wireless local are network (WLAN) communication. 802.11b/g/n uses the 2.4 GHz band.

Keystone Correction — Device that will correct an image of the distortion

(usually a wide-top narrow-bottom effect) of a projected image caused by improper projector to screen angle.

Maximum Distance — The distance from a screen the projector can be to cast an image that is usable (bright enough) in a fully darkened room.

Maximum Image Size — The largest image a projector can throw in a darkened room. This is usually limited by focal range of the optics.

Glossary 117

Minimum Distance — The closest position that a projector can focus an image onto a screen.

NTSC — National Television Standards Committee. North American standard for video and broadcasting, with a video format of 525 lines at 30 frames per second.

PAL — Phase Alternating Line. A European broadcast standard for video and broadcasting, with a video format of 625 lines at 25 frames per second.

Reverse Image — Feature that allows you to flip the image horizontally. When used in a normal forward projection environment text, graphics, etc. are backwards. Reverse image is used for rear projection.

RGB — Red, Green, Blue — typically used to describe a monitor that requires separate signals for each of the three colors.

S-Video — A video transmission standard that uses a 4-pin mini-DIN connector to send video information on two signal wires called luminance (brightness, Y) and

SECAM — A French and international broadcast standard for video and broadcasting, closely related to PAL but with a different method of sending color information.

SSID — Service Set Identifiers — A name used to identify the particular wireless

LAN to which a user wants to connect.

SVGA — Super Video Graphics Array — 800 x 600 pixels count.

SXGA — Super Extended Graphics Array, — 1280 x 1024 pixels count.

UXGA — Ultra Extended Graphics Array — 1600 x 1200 pixels count.

VGA — Video Graphics Array — 640 x 480 pixels count.

WEP — Wired Equivalent Privacy — This is a method for encrypting communication data. The encryption key is created and notified only to the communicating user, so the communication data cannot be decrypted by a third party.

XGA — Extended Video Graphics Array — 1024 x 768 pixels count.

WXGA — Wide Extended Graphics Array — 1280 x 800 pixels count.

1080p — 1080p is the shorthand identification for a set of HDTV high-definition video modes that are characterized by 1080 horizontal lines of resolution and progressive scan, meaning the image is not interlaced as is the case with the 1080i display standard.

Zoom Lens — Lens with a variable focal length that allows operator to move the view in or out making the image smaller or larger.

Zoom Lens Ratio — Is the ratio between the smallest and largest image a lens can

118 Glossary

the project from a fixed distance. For example, a 1.4:1 zoom lens ratio means that a 10 foot image without zoom would be a 14 foot image with full zoom.

Glossary 119

Index

A

Adjusting the Projected Image 26

Elevator button 26

lower the projector

Elevator foot 26

Tilt adjustment wheel 26

Lowering the Projector Height

26

Raising the Projector Height 26

Adjusting the Projector Zoom and

Focus 27

Focus ring 27

Horizontal lens shift knob 27

Lens shift lock 27

Side door 27

Vertical lens shift knob 27

Zoom ring 27

C

Changing the Lamp 106

Connecting the Projector

12 V DC Plug 23

3 RCA to 3 RCA Component

Video (Male to Male) cable

20

Composite Video cable 18

Connecting a Computer with a

RS232 cable 14 ,

15

Connecting with a Component

Cable 19

Connecting with a Composite

Cable 18

Connecting with an HDMI

Cable 21

Connecting with an S-video

Cable 17

HDMI cable 21

, 22

Motorized projection screen 23

Power cord 12

18 ,

19 ,

20

,

,

13

21

,

,

14

22

,

,

15

23

,

,

17 ,

24

RS232 (9-pin D-sub female to female pin2-3 swap) cable

14 ,

24

S-Video cable 17

To Computer 12

USB to USB cable 12

USB-A to USB-B cable 15

,

13

VGA to YPbPr cable 19

Connection Ports

+12 V DC out connector 10

Audio input connector 10

Audio output connector 10

Component Video input

connector 10

Composite Video connector 10

HDMI-A connector 10

HDMI-B connector 10

Mini USB (Mini Type B) connector for remote

control 10

Power cord connector 10

120 Index

RJ45 connector 10

RS232 (D-sub) connector 10

Security cable slot 10

S-Video connector 10

USB Type A connector for USB

Viewer 10

USB Type B connector for USB

Display 10

VGA-A input (D-sub) connector

10

VGA-A output (monitor

loop-through) connector 10

VGA-B input (D-sub) connector

10

WiFi USB (Type A) connector

10

Contact Dell 7 ,

104 ,

106

Control Panel 30

O

On-Screen Display 37

ADVANCED SETTINGS 40

AUDIO INPUT 40

AUTO ADJUST 38

BRIGHTNESS/CONTRAST 39

HELP 54

INPUT SOURCE 37

INPUT SOURCE MULTIPLE

DISPLAY 38

LANGUAGE 54

VIDEO MODE 39

VOLUME 40

P

phone numbers 115

Powering On/Off the Projector

Powering Off the Projector 25

Powering On the Projector 25

D

Dell

contacting 115

R

Remote Control 32

IR receiver 31

M

Main Unit 8

Control panel 8

Elevator button for height

adjustments 8

Focus tab 8

IR receivers 8

Lens 8

Lens cap 8

S

Specifications

Audio 109

Brightness 108

Color Wheel Speed 108

Contrast Ratio 108

Dimensions 109

Displayable Color 108

Index 121

Environmental 109

I/O Connectors 109

Light Valve 108

Noise Level 109

Number of Pixels 108

Power Consumption 109

Power Supply 108

Projection Distance 108

Projection Lens 108

Projection Screen Size 108

RS232 Protocol 112

Uniformity 108

Video Compatibility 108

Weight 109

support

contacting Dell 115

T

telephone numbers 115

Troubleshooting 101

Contact Dell 101

122 Index

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Windows 10 Home 64-bit
  • Intel Core i7-10750H (12MB Cache, 2.6GHz)
  • 43.9 cm (17.3") Full HD 1920 x 1080, NVIDIA GeForce RTX 2060 (6GB GDDR6)
  • 16GB (2933MHz) DDR4-SDRAM (2 x 8) & 1000GB SSD

Related manuals

advertisement

Table of contents