Data Sheet AFL Catalog Optical Test
Table of Contents
Optical Time Domain Reflectometers (OTDRs)
and Fault Locators
C850 Compact QUAD OTDR with QUAD OLS and OPM . . . . . . . . . 3
M700 Compact Single-mode OTDR . . . . . . . . . . . . . . . . . . . . . . . 7
M650 Compact QUAD OTDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
M200 Handheld OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
OFL 280 Handheld FTTx OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . 15
OFL 250 Handheld Single-mode OTDR. . . . . . . . . . . . . . . . . . . . 18
OFL 200 Handheld Single-mode OTDR. . . . . . . . . . . . . . . . . . . . 20
Fiber Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SLP4-FTTH and SLP4-7 Triple Wave Test Kit with Wave ID and
Set Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SLP4-6D Single-mode Test Kit with Wave ID & Set Reference. . . . 56
MLP5-2 Multimode Test Kit with Wave ID, Set Reference &
Data Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
MLP4-2 Multimode Test Kit with Wave ID & Set Reference . . . . . . 60
MLP1 Basic Multimode Test Kit . . . . . . . . . . . . . . . . . . . . . . . . . 62
CKSM-2 Contractor Series Multimode & Single-mode Test Kit
with Set Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
CKM-2 Contractor Series Multimode Test Kit with Set Reference . 65
OTDR and Certification Test Kits
C860 QUAD OTDR and Certification Test Kit. . . . . . . . . . . . . . . . . 23
Visual Fault Identifiers
VFI 2 Visual Fault Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
HiLite Visual Fault Identiier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
MT Tracer Muti-fiber Visual Fault Identifier. . . . . . . . . . . . . . . . . . 68
Fiber Test Kits
FTK Pro Installer Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Optical Fiber Identifiers
OFI-FTTx Active ONT Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . 69
OFI 400 Optical Fiber Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . 70
OFI 200 Optical Fiber Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . 70
Certification, Optical Loss and Return Loss Test
Sets
C880 QUAD Certification Test Kit. . . . . . . . . . . . . . . . . . . . . . . . . 28
TurboTest - 500B Broadband Loss/Return Loss Test Set. . . . . . . . 31
OLTS 5 - Broadband Loss Test Set . . . . . . . . . . . . . . . . . . . . . . . 32
ORL 3B - Optical Return Loss Test Set. . . . . . . . . . . . . . . . . . . . . 33
Microscopes & Videoscopes
OFS 300 Optical Microscope (for connectors on patch cords). . . . 72
VS 300 Video Microscope (for connectors on patch cords). . . . . . 73
VFS 2 Video Fiber Scope (for connectors in panels) . . . . . . . . . . . 74
VCP 1 USB Video Capture Port. . . . . . . . . . . . . . . . . . . . . . . . . . 75
Optical Power Meters
OPM4-FTTx PON Power Meter. . . . . . . . . . . . . . . . . . . . . . . . . . 34
OPM5 OPM with Wave ID, Set Reference, and Data Storage. . . . . 35
OPM4 OPM with Wave ID, and Set Reference . . . . . . . . . . . . . . . 36
OPM1 Optical Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CSM1 Contractor Series Optical Power Meter . . . . . . . . . . . . . . . 38
Talk Sets & Attenuators
FTS Series Fiber Optic Talk Sets. . . . . . . . . . . . . . . . . . . . . . . . . 76
SVA 1 Single-Mode Variable Attenuator. . . . . . . . . . . . . . . . . . . . 77
VOA 5 Variable Fiber Optic Attenuator. . . . . . . . . . . . . . . . . . . . . 78
LED & Laser Light Sources
OLS7- FTTH & OLS7-3 Triple Wavelength Laser Sources . . . . . . . 39
OLS4 Integrated Laser & LED Light Source with Wave ID. . . . . . . 40
OLS2-DUAL Laser Light Source with Wave ID . . . . . . . . . . . . . . . 41
OLS1-DUAL LED Laser Light Source with Wave ID. . . . . . . . . . . . 42
OLS1 LED Light Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
CSS1-SM Contractor Series Dual Laser Light Source. . . . . . . . . . 44
CSS1-MM Contractor Series Dual LED Light Source. . . . . . . . . . . 45
Network Simulators
NS1 and NS2 Network Simulators. . . . . . . . . . . . . . . . . . . . . . . . 79
NSR Network Simulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Optical Loss Test Kits
SMLP5-5 SM/MM Test Kit with Wave ID, Set Reference &
Data Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
SMLP4-4 SM / MM Test Kit with Wave ID & Set Reference. . . . . . 48
SLP5-FTTH and SLP5-7 Triple Wave Test Kit with Wave ID,
Set Reference, and Data Storage . . . . . . . . . . . . . . . . . . . . . 50
SLP5-6D Single-mode Test Kit with Wave ID, Set Reference &
Test & Inspection
Data Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
AFL’s Noyes Test & Inspection Equipment product line offers a
comprehensive set of fiber optic test equipment for measuring,
maintaining and documenting the performance of fiber optic
networks. In every area of manufacturing, AFL combines the
latest equipment, production techniques and test systems to
create products with world-class performance.
4Q09
1
2
C850 Compact QUAD OTDR with QUAD OLS and OPM
Features
The Noyes C850 from AFL Telecommunications is a full-featured QUAD OTDR in a compact
case with a large transflective touch screen display suitable for both indoor and outdoor
operation. The C850 offers built-in auto test functionality when used with another C850
or the C840 QUAD Certification Tester. The C850 features single-mode and multimode
OTDR capabilities, both single-mode and multimode Optical Light Sources (OLS), Visual
Fault Locator (VFL, 650 nm), and an Optical Power Meter (OPM). As an OTDR, the C850
supports Full Auto, Expert (manual) and Real-Time test modes, simultaneous dual and
single wavelength testing, and Event and Pass/Fail analysis based on default or userdefined thresholds.
Two C850s or a C840 Tester and C850 can be used together to perform Tier 1 dual
wavelength MM (850/1300 nm) and SM (1310/1550 nm) auto tests of one or two fibers in
one or both directions as well as measure both loss and length of the fibers and compare
to industry standards (TIA/ISO/EN), applications and user-defined thresholds values to
certify the fibers. The user may test two fibers at two wavelengths bi-directionally and
store the results into the main unit. Featuring rich file naming, the Job setup wizard allows
the user to define both the cable and fiber end locations, creating easily identifiable trace
files, which are managed into Job and Cable folders.
•• OTDR dynamic range:
- 22 dB (MM)
- 26 dB (SM)
•• Integrated OPM, OLS, and VFL (650 nm)
•• OLS sources:
- LED - 850/1300 nm
- Laser - 1310/1550 nm
•• Full Auto, Expert, Real-Time OTDR test
modes
•• 6.5-inch transflective (indoor/outdoor)
touch screen display
•• Tool-free, switchable test port adapters
•• Rechargeable Li-Ion battery (> 8 hours)
or AC power
•• USB host and function ports
•• Bellcore (GR-196) .SOR file format
•• Internal (1000s tests) and USB storage
•• Wave ID detect if used with Noyes Wave
ID series light sources
•• Windows® compatible software
Applications
•• Tier 1 and Tier 2 testing of premise
networks
•• Bi-directional two fibers and single fiber
test capable
•• Perform Pass/Fail Event and Link
measurements
•• Find faults using integrated Visual Fault
Locator
•• Save loss or power measurements
•• Use as single-mode laser or multimode
LED source
•• Certify fibers using Pass/Fail criteria of
industry standards, applications and
user-defined limits
•• Create professional certification reports
© 2009, AFL Telecommunications, all rights reserved. C850-00-2000 Revision 1D, 2009-10-07
Specifications are subject to change without notice.
3
C850 Compact QUAD OTDR with QUAD OLS and OPM
Ordering Information
The C850 OTDR Kits and Options allow users to buy the test
equipment functionality needed today and grow to meet the
demands of certification testing.
The C850 combined with an OLS 4 source will allow users to test
and generate detailed reports with both OTDR and Loss results
shown for each fiber and in charts by cable.
Users can add a C840 or another C850 to perform Certification
testing. Two C850s or a C840 Tester and C850 can be used
together to perform Tier 1 dual wavelength MM (850/1300
nm) and SM (1310/1550 nm) auto tests of one or two fibers in
one or both directions as well as measure both loss and length
of the fibers and compare to industry standards (TIA/ISO/EN),
applications and user-defined thresholds values to certify the
fibers.
When placing an order, select options as follows: Model, Optical Configuration, Language, and Case.
Example: C850 — 100 — LP1 — H2
C850
NNN
LLL
CC
Case (CC)
Model
C850
S1 = Soft case
H1 = Hard case and soft case with cleaning
accessories
H2 = Hard and soft case with SC-LC test and
cleaning accessories
H3 = H2 option plus OFS300-200X microscope
H4 = H2 option plus spare battery and charger
H5 = Hard and soft case with SC-ST test and
cleaning accessories
H6 = H5 option plus OFS300-200X microscope
H7 = H5 option plus spare battery and charger
Optical Configuration (NNN)
100 = QUAD 850/1300 nm MM and 1310/1550 nm SM
Language (LLL)
LP1 = Language Pack: English, German, French, Spanish, Italian, Portuguese
JPN = Japanese/English
CHI = Chinese/Taiwanese/English
RUS = Russian/English
KOR = Korean/English
ARA = Arabic/English
Continued on the next page
© 2009, AFL Telecommunications, all rights reserved. C850-00-2000 Revision 1D, 2009-10-07
Specifications are subject to change without notice.
4
C850 Compact QUAD OTDR with QUAD OLS and OPM
Ordering Information (continued)
Each C850 kit includes the C850 OTDR, USB Flash drive, PC software for OTDR trace analysis and certification or OPM loss reporting, AC
adapter, switchable test ports adapters and accessories (see table below).
Kit model number
carry Case and Accessories
Fiber
Rings1
C850-100-LP1-S1
Soft case
C850-100-LP1-H1
Soft and hard cases
—
—
C850-100-LP1-H2
Soft and hard cases
SC/LC
C850-100-LP1-H3
Soft and hard cases, OFS300-200C
C850-100-LP1-H4
Soft and hard cases, charger, spare battery
C850-100-LP1-H5
Adapters
OTDR/OLS
OPM
VFI
One-Click Cleaner SC/ST/FC, 2.5mm SC, ST, LC SC, 2.5mm, 1.25mm 2.5mm 1.25mm
Cleaning Products
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
SC/LC
One-Click Cleaner SC/ST/FC, 2.5mm SC, ST, LC
One-Click Cleaner LC, 1.25mm
SC, ST, LC
Cletop - SB white tape
SC, ST, LC
SC/LC
SC, ST, LC
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
Soft and hard cases
SC/ST
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
C850-100-LP1-H6
Soft and hard cases, OFS300-200C
SC/ST
One-Click Cleaner SC/ST/FC, 2.5mm SC, ST, LC
Cletop - SB white tape
SC, ST, LC
C850-100-LP1-H7
Soft and hard cases, charger, spare battery
SC/ST
SC, ST, LC
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
SC, 2.5mm, 1.25mm 2.5mm 1.25mm
1 (2) each - 150m (62.5µm, 50µm, SM)
C850—100—LP1—H2 (or H5) Kit Contents
Optional OTDR and Cleaning Accessories
Item
Description
Model Number
Description
C850
QUAD OTDR/Auto Test Certification Tester
FR1-SM-150-SC-FC
Fiber ring, single-mode, SC/FC, 150 m
Adapters
OTDR and OLS ports — SC, ST, LC
OPM port — SC, 1.25 and 2.5mm Universal
VFI port — 1.25 and 2.5mm Universal
FR1-SM-150-SC-LC
Fiber ring, single-mode, SC/LC, 150 m
FR1-M6-150-SC-ST
Fiber ring, multimode, 62.5mm, SC/ST, 150 m
Fiber Rings (6)
150 m (62.5mm, 50mm, SM)
FR1-M6-150-SC-LC
Fiber ring, multimode, 62.5mm, SC/LC, 150 m
Miscellaneous
Accessories
Mandrel — 62.5mm, 3mm jacket
FR1-M5-150-SC-ST
Fiber ring, multimode, 50mm, SC/ST, 150 m
FR1-M5-150-SC-LC
Fiber ring, multimode, 50mm, SC/LC, 150 m
Mandrel — 50mm, 3mm jacket
Stylus pen for touch screen
USB thumb drive, 1G
USB to mini-USB cable
Small plastic parts box (2) to store adapter caps and mandrels
AC adapter (1), specify country of use
Cleaning
Accessories
One-Click Cleaner SC/ST/FC, 2.5mm (H2 and H5 kit)
One-Click Cleaner LC/MU, 1.25mm (H2 kit only)
Cletop SB white tape
Cases
Hard transit case — holds C850, and above accessories
Fiber ring, laser optimized, multimode, 50mm, SC/LC, 150 m
FR1-L5-150-SC-SC
Fiber ring, laser optimized, multimode, 50mm, SC/SC, 150 m
FR1-SM-500-SC-LC
Fiber ring, single-mode, SC/LC, 500 m
FR1-SM-500-SC-SC
Fiber ring, single-mode, SC/SC, 500 m
FR1-SM-500-SC-FC
Fiber ring, single-mode, SC/FC, 500 m
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
8500-05-0001MZ
One-Click Cleaner SC/ST/FC
8500-05-0002MZ
One-Click Cleaner LC/MU
8500-10-0017MZ
Replacement tape for Cletop (white)
Note: 1000 m single-mode fiber rings are also available.
Soft case for C850
Documentation
FR1-L5-150-SC-LC
User guides and quick reference guides
Report Software PC software and user guide
Continued on the next page
© 2009, AFL Telecommunications, all rights reserved. C850-00-2000 Revision 1D, 2009-10-07
Specifications are subject to change without notice.
5
C850 Compact QUAD OTDR with QUAD OLS and OPM
Specifications
(All specifications valid at 25°C unless otherwise specified)
OTDR
Multimode
Single-mode
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Center Wavelengths
Wavelength Tolerance
850/1300 nm
1310/1550 nm
± 20/30 nm
± 20/30 nm
22 dB
26 dB
Dynamic Range (SNR = 1)
10, 30, 100, 300 ns; 1, 3, 10 ms
Pulse Widths
Range Settings
250 m to 64 km
Sampling Points
250 m to 208 km
0.25 m
Group Index of Refraction (GIR)
+6 to -60 dBm
Accuracy 1
±0.25
2
dB, dBm, mW
Yes (to -47 dBm)
Set Reference
Yes
Data Storage
Yes
Tone Detection
Yes (to -47 dBm)
± (1 + 0.005% x distance + data point spacing)
general
± 0.05 dB/dB
Test Modes
OTDR (Full Auto, Expert, Real-Time), Auto Test, OPM,
OLS, VFL
Trace File Format
SR-4731 (GR-196-CORE Appendix A, B; SR-4731)
1 Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
2 Typical distance from event location to point where trace is within 0.5 dB of
backscatter caused by a -45 dB event using 10 ns pulse width.
3 Does not include GIR uncertainty.
Multimode port
850/1300 nm (nominal)
Single-mode port
1310/1550 nm (nominal)
LED
Laser
Emitter Type
Safety Class
Measurement Range
1.4000 to 1.6000
Linearity
Light Source
Available Wavelengths
InGaAs 2mm
1 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
2 Automatic wavelength identification and switching when used with Noyes Wave
ID Series Light Sources.
Up to 16,000
Min. Data Point Spacing
850, 1300 1310, 1490, 1550, 1625 nm
Detector Type
Wavelength ID
9m
Attenuation Dead Zone 2
Calibrated Wavelengths
Measurement Units
1.5 m
Event Dead Zone 1
Distance Uncertainty (m) 3
Power Meter
Length Measurement Range 5 km (MM);
200 km (SM)
Data Storage
USB flash drive (2.0)
Downloadable from unit directly to PC
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Output Power
> - 20 dBm, 62.5µm
MM 1
0 dBm, 9µm SM
Stability (after 15 minutes
warm up)
± 0.1 dB over 1 hour
± 0.07 dB over 1 hour
± 0.15 dB over 8 hours
Wave ID Transmit
Yes
Tone Generation
270 Hz, 330 Hz, 1 kHz, 2 kHz
1 Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped
jumper is used instead of a 62.5 µm mandrel-wrapped jumper.
Visual Fault Locator
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Wavelength
650 nm
Output Power (nominal)
0.8 mW
Internal flash memory
Data Storage Capacity
Internal > 1000 fibers
Data Transfer to PC
USB
Tool Free Adapters
Modular cleanable SC/ST/LC
Size
27.4 x 19.3 x 7.1 cm
(10.8 x 7.6 x 2.8 in)
Weight
2.3 kg ( 5 lb)
Operating Temperature
-10 to +50°C, 0 to 90% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
Power
Rechargeable Li-Ion or AC power adapter
Battery Life 1
> 8 hours continuous testing
Recharge Time 2
4 hours
Display
16.51 cm (6.5 in),
color, transflective
1 Typical, depending on display brightness.
2 Typical, from fully discharged to fully charged state, unit may be operating.
External battery charger available.
© 2009, AFL Telecommunications, all rights reserved. C850-00-2000 Revision 1D, 2009-10-07
Specifications are subject to change without notice.
6
M700 Compact Single-mode OTDR
The Noyes M700 from AFL Telecommunications is a compact,
full-featured, single-mode OTDR that includes an integrated Visual
Fault Locator (VFL), an Optical Power Meter (OPM) capable of
displaying up to three wavelengths simultaneously, and a large
transflective touch screen display suitable for both indoor and
outdoor operation.
The M700 OTDR supports Real-Time, Full-Auto, and Expert
(manual) modes, precision event analysis, dual-wavelength testing,
rich file naming, and an intuitive job set-up functionality. In addition
to OTDR event analysis, pass/fail acceptance values can be set to
alert the test operator of failing or marginal events. Using one of
the Least Squares Approximation (LSA) loss methods, events may
be added or deleted manually.
Thousands of OTDR and OPM test results can be stored internally
or on the supplied USB drive, and are transferable via a USB cable
or drive to a computer for viewing, printing and analyzing with
supplied Windows® compatible software. Saved OPM loss values
for a cable in one or two directions can be displayed in a table on
the M700 for evaluation and comparison.
Features
•• 38/36 dB dynamic range @ 1310/1550 nm
•• Integrated Optical Power Meter (OPM) and Visual Fault Locator
(VFL, 650 nm)
•• LSA Measurements and manual events in Expert mode
•• Pass/Fail Event and Link Thresholds settings
•• OTDR results saved as industry standard (GR-196) .SOR files
•• OPM stores results and displays up to three wavelengths simultaneously
•• Large, high bright, sunlight readable, transflective touchscreen
•• Tool-free, switchable adapters (SC/FC/LC)
•• Integrated fiber launch ring holder
•• 2 USB host ports
•• USB drive and Windows® compatible software included
With short dead zones, a dynamic range of 38 dB, and greater
than 8-hour battery life during continuous testing, the M700 is
perfect for testing optical fibers in service provider metro areas.
Ordering Information
Model
Description
Test Port Adapters
M700-11-0901PR 1310/1550 nm single-mode OTDR SC, FC, and LC *
* ST test port adapter is available (order separately).
Standard accessories include are USB Flash drive, PC software for OTDR trace
analysis and OPM Loss reporting, AC adapter, user guide, soft carry case, 1.25
and 2.5mm Universal adapters for VFL and OPM, SC, FC and LC adapters for
the OTDR (ST available, purchased separately).
Continued on the next page
© 2008-2009 AFL Telecommunications, all rights reserved. M700-00-2000 Revision 1F, 2009-07-16
Specifications are subject to change without notice.
7
M700 Compact Single-mode OTDR
Specifications
Power Meter
OTDR
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Center Wavelengths
1310/1550 nm
Dynamic Range (SNR = 1)
38/36 dB (1310/1550 nm)
Accuracy
Event Dead Zone 1
0.9 m
Measurement Units
dB, dBm, mW
Attenuation Dead Zone 2
4.5 m
Wavelength ID 5
Yes
Pulse Widths
5, 10, 30, 100, 300 ns, 1, 3, 10, 20 ms
Set Reference
Yes
Range Settings
250 m to 256 km
Data Storage
Yes
Sampling Points
max. 64,000 points
Tone Detection
270 Hz, 330 Hz, 1 kHz, 2 kHz
Min Data Point Spacing
0.125 m
Group Index of Refraction (GIR)
Distance Uncertainty (m)
3
1.4000 to 1.6000
± 0.05 dB/dB (typical)
Trace File Format
Bellcore GR-196 Version 1.1
Internal flash memory
Trace File Storage Media
USB flash drive
Downloadable from OTDR directly to PC
Trace File Storage Capacity
Internal 1000 fibers
Data Transfer to PC
USB
OTDR Modes
Full Auto, Real Time, Expert
Tool Free adapters
Modular cleanable SC/ST/FC/LC
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Wavelength
650 nm
Output Power (nominal)
0.8 mW
Filtered InGaAs detector
Measurement Range (dBm)
+26 to -50 dBm
4
±0.25
Size
27.4 x 19.3 x 7.1 cm (10.8 x 7.6 x 2.8 in)
Weight
2.3 kg ( 5 lb)
Operating Temperature
-10 to +50°C, 0 to 90% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
Power
Rechargeable Li-Ion or AC power adapter
Recharge Time
> 8 hours continuous OTDR testing
7
Display
4 hours
6.5 in (16.51 cm), color, transflective
4 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
5 Automatic wavelength identification and switching when used with Noyes Wave
ID Series Light Sources.
6 Typical, depending on display brightness.
7 Typical, from fully discharged to fully charged state, unit may be operating.
All specifications are subject to change.
All specifications valid at 25°C unless otherwise specified.
External battery charger available.
Visual Fault Locator
Laser
Detector Type
Battery Life 6
1 Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 5 ns pulse width.
2 Typical distance from event location to point where trace is within 0.5 dB of
backscatter caused by a -45 dB event using 5 ns pulse width.
3 Does not include GIR uncertainty.
Emitter Type
850, 980, 1310, 1490, 1550, 1625 nm (displays
up to 3 simultaneously)
General
± (1 + 0.0005% x distance + data point spacing)
Linearity
Calibrated Wavelengths
OTDR Fiber Accessories
Model Number
Description
FR1-SM-1KM-SC-FC
Fiber Ring SM SC/FC 1000m
FR1-SM-1KM-SC-LC
Fiber Ring SM SC/LC 1000m
FR1-SM-1KM-ASC-SC
Fiber Ring SM SC-APC/SC-UPC 1000m
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
© 2008-2009 AFL Telecommunications, all rights reserved. M700-00-2000 Revision 1F, 2009-07-16
Specifications are subject to change without notice.
8
M650 Compact QUAD OTDR
Features
•• 22 dB (MM), 26 dB (SM) dynamic range
•• Integrated OPM and VFL (650 nm)
•• Full Auto, Expert, and Real-Time OTDR
test modes
•• 6.5-inch transflective (indoor/outdoor)
touch screen display
•• Tool-free, switchable test port adapters
•• Rechargeable Li-Ion battery (> 8 hours)
or AC power
•• USB host and function ports
•• Bellcore (GR-196) .SOR file format
•• Internal (1000s test results) and USB
storage
•• Windows® compatible software
Applications
The Noyes M650 from AFL Telecommunications is a compact, full-featured, QUAD OTDR
with an integrated Visual Fault Locator (VFL, 650 nm), Optical Power Meter (OPM), and
a large transflective touch screen display suitable for both indoor and outdoor operation.
With short dead zone and intermediate range specifications, the M650 is ideal for Tier 2
testing of premises (building and campus) networks.
•• Tier 1 and 2 testing of premise networks
•• Perform Pass/Fail Event and Link
measurements
•• Find faults using integrated Visual Fault
Locator
•• Save loss or power measurement
•• Splice verification
•• Network documentation
The M650 OTDR supports Full Auto, Expert (manual), and Real-Time test modes, precision
event analysis, dual-wavelength testing, rich file naming, and an intuitive job setup
functionality. In addition to OTDR event analysis, pass/fail acceptance values can be set
to alert the test operator of failing or marginal events. Using one of the Least Squares
Approximation (LSA) loss methods, events may be added or deleted manually.
Thousands of test results may be stored internally for transfer to a computer via a
USB cable or a standard USB drive. Once test data is transferred to a computer, the
supplied Windows® compatible software allows technicians to view, print, and generate
professional reports. Saved OPM loss values for a cable in one or two directions can be
displayed in a table on the M650 OTDR for evaluation and comparison.
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. M650-00-2000 Revision 1G, 2009-10-12
Specifications are subject to change without notice.
9
M650 Compact QUAD OTDR
M650-100-LP1-S1 Kit
M650-100-LP1-H2 (or H5) Kit
Ordering Information
When placing an order, select options as follows: Model, Optical Configuration, Language, and Case.
Example: M650 — 100 — LP1 — H2
M650
NNN
LLL
CC
Case (CC)
Model
M650
S1 = Soft case
H1 = Hard and soft case with cleaning
accessories
H2 = Hard and soft case with SC-LC test and
cleaning accessories
H3 = H2 option plus OFS300-200X microscope
H4 = H2 option plus spare battery and charger
H5 = Hard and soft case with SC-ST test and
cleaning accessories
H6 = H5 option plus OFS300-200X microscope
H7 = H5 option plus spare battery and charger
H9 = H6 option plus OLS4 light source
Optical Configuration (NNN)
100 = QUAD 850/1300 nm MM and 1310/1550 nm SM
Language (LLL)
LP1 = Language Pack: English, German, French, Spanish, Italian, Portuguese
JPN = Japanese/English
CHI = Chinese/Taiwanese/English
RUS = Russian/English
KOR = Korean/English
ARA = Arabic/English
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. M650-00-2000 Revision 1G, 2009-10-12
Specifications are subject to change without notice.
10
M650 Compact QUAD OTDR
Ordering Information (continued)
Combining the M650 with an OLS 4 source will allow users to test
and generate detailed reports with both OTDR and Loss results
shown for each fiber and in charts by cable.
Kit model number
carry Case and Accessories
Each M650 kit includes the M650 OTDR, USB Flash drive, PC
software for OTDR trace analysis and OPM loss reporting, AC
adapter, switchable test ports adapters, and accessories (see table
below).
Fiber
Rings1
Cleaning Products
—
M650-100-LP1-S1
Soft case
M650-100-LP1-H1
Soft and hard cases
—
M650-100-LP1-H2
Soft and hard cases
SC/LC
M650-100-LP1-H3
Soft and hard cases, OFS300-200C
SC/LC
M650-100-LP1-H4
Soft and hard cases, charger, spare battery
SC/LC
Adapters
OTDR
OPM
VFI
One-Click Cleaner SC/ST/FC, 2.5mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
One-Click Cleaner SC/ST/FC, 2.5mm
One-Click Cleaner LC, 1.25mm
Cletop - SB white tape
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
M650-100-LP1-H5
Soft and hard cases
SC/ST
M650-100-LP1-H6
Soft and hard cases, OFS300-200C
SC/ST
One-Click Cleaner SC/ST/FC, 2.5mm
Cletop - SB white tape
M650-100-LP1-H7
Soft and hard cases, charger, spare battery
SC/ST
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
M650-100-LP1-H9
Soft and hard cases, OLS4, OFS300-200C
SC/ST
SC, ST, LC
SC, 2.5mm, 1.25mm
2.5mm 1.25mm
1 (2) each - 150m (62.5µm, 50µm, SM)
M650—100—LP1—H2 (or H5) Kit Contents
Optional Accessories
Item
Description
Model Number
Description
M650
QUAD OTDR
FR1-SM-150-SC-FC
Fiber ring, single-mode, SC/FC, 150 m
Adapters
OTDR port — SC, ST, LC
OPM port — SC, 1.25 and 2.5mm Universal
VFI port — 1.25 and 2.5mm Universal
FR1-SM-150-SC-LC
Fiber ring, single-mode, SC/LC, 150 m
FR1-M6-150-SC-ST
Fiber ring, multimode, 62.5mm, SC/ST, 150 m
Fiber Rings (6)
150 m (62.5mm, 50mm, SM)
FR1-M6-150-SC-LC
Fiber ring, multimode, 62.5mm, SC/LC, 150 m
Miscellaneous
Accessories
Stylus pen for touch screen
FR1-M5-150-SC-ST
Fiber ring, multimode, 50mm, SC/ST, 150 m
FR1-M5-150-SC-LC
Fiber ring, multimode, 50mm, SC/LC, 150 m
USB thumb drive, 1G
USB to mini-USB cable
Small plastic parts box (2) to store adapter caps and mandrels
AC adapters (1), specify country of use
Cleaning
Accessories
One-Click Cleaner SC/ST/FC, 2.5mm (H2 and H5 kit)
One-Click Cleaner LC/MU, 1.25mm (H2 kit only)
Cletop SB white tape
Cases
Hard transit case — holds M650, and above accessories
Soft case for M650
Documentation
User guides and quick reference guides
FR1-L5-150-SC-LC
Fiber ring, laser optimized, multimode, 50mm, SC/LC, 150 m
FR1-L5-150-SC-SC
Fiber ring, laser optimized, multimode, 50mm, SC/SC, 150 m
FR1-SM-500-SC-LC
Fiber ring, single-mode, SC/LC, 500 m
FR1-SM-500-SC-SC
Fiber ring, single-mode, SC/SC, 500 m
FR1-SM-500-SC-FC
Fiber ring, single-mode, SC/FC, 500 m
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
8500-05-0001MZ
One-Click Cleaner SC/ST/FC, 2.5mm
8500-05-0002MZ
One-Click Cleaner LC/MU, 1.25mm
8500-10-0017MZ
Replacement tape for Cletop (white)
Note: 1000 m single-mode fiber rings are also available.
Report Software PC software and user guide
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. M650-00-2000 Revision 1G, 2009-10-12
Specifications are subject to change without notice.
11
M650 Compact QUAD OTDR
Specifications
(All specifications valid at 25°C unless otherwise specified)
OTDR
Multimode
Single-mode
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Center Wavelengths
Wavelength Tolerance
850/1300 nm
1310/1550 nm
± 20/30 nm
± 20/30 nm
22 dB
26 dB
Dynamic Range (SNR = 1)
Accuracy
dB, dBm, mW
9m
Set Reference
Yes
10, 30, 100, 300 ns; 1, 3, 10 ms
Data Storage
Yes
Tone Detection
Yes
250 m to 208 km
Up to 16,000
Min. Data Point Spacing
1 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
2 Automatic wavelength identification and switching when used with Noyes Wave
ID Series Light Sources.
0.25 m
Group Index of Refraction (GIR)
3
1.4000 to 1.6000
± (1 + 0.005% x distance + data point spacing)
Linearity
Trace File Format
+6 to -60 dBm
±0.25
1
Yes
250 m to 64 km
Sampling Points
InGaAs 2mm
Wavelength ID 2
Attenuation Dead Zone 2
Range Settings
Detector Type
Measurement Range (dBm)
1.5 m
Pulse Widths
850, 1300 1310, 1490, 1550, 1625 nm (displays
up to 3 simultaneously)
Measurement Units
Event Dead Zone 1
Distance Uncertainty (m)
Power Meter
Calibrated Wavelengths
General
± 0.05 dB/dB (typical)
Size
27.4 x 19.3 x 7.1 cm (10.8 x 7.6 x 2.8 in)
Weight
2.3 kg ( 5 lb)
Internal flash memory
Operating Temperature
-10 to +50°C, 0 to 90% RH (non-condensing)
USB flash drive (2.0)
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
Power
Rechargeable Li-Ion or AC power adapter
SR-4731 (GR-196-CORE Appendix A & B and
SR-4731)
Trace File Storage Medium
Downloadable from OTDR directly to PC
Trace File Storage Capacity
Internal > 1000 fibers
Data Transfer to PC
USB
OTDR Modes
Full Auto, Expert, Real-Time
Tool Free adapters
Modular cleanable SC/ST/LC
> 8 hours continuous OTDR testing
Battery Life 1
Recharge Time
Display
2
4 hours
16.51 cm (6.5 in), color, transflective
1 Typical, depending on display brightness.
2 Typical, from fully discharged to fully charged state, unit may be operating.
External battery charger available.
1 Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
2 Typical distance from event location to point where trace is within 0.5 dB of
backscatter caused by a -45 dB event using 10 ns pulse width.
3 Does not include GIR uncertainty.
Visual Fault Locator
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Wavelength
650 nm
Output Power (nominal)
0.8 mW
© 2008-2009, AFL Telecommunications, all rights reserved. M650-00-2000 Revision 1G, 2009-10-12
Specifications are subject to change without notice.
12
M200 Handheld OTDR
The Noyes M200 from AFL Telecommunications offers unmatched OTDR capabilities
in a handheld package weighing less than 1 kg (2 lb). Multimode, Single-mode, and
‘Quad’ wavelength models are offered. With short dead zone and intermediate range
specifications, the M200 is ideal for Tier 2 testing of premises (building and campus)
networks or certification and troubleshooting of FTTX PON networks. And its bright,
transflective display makes it suitable for both indoor and outdoor operation.
The M200 is based on a new hardware/software platform that supports automatic and
manual setup, precision event analysis, dual-wavelength testing, rich file naming and
folder setup, 6-hour battery life, internal and removable media data storage, and USB
connectivity. Test ports are equipped with tool-free adapters, which can be changed in
seconds. A custom-designed polycarbonate case and shock-absorbing boot make it our
most rugged OTDR ever.
Results are saved as industry standard .SOR files, which can be viewed, printed, and
analyzed on a PC using free-ware available to you and your customers (go to www.afltele.
com to download). Unit firmware, user settings, and test results are saved in non-volatile
memory. Thus the M200 may be stored with battery removed for an extended period of
time and still be up and running in seconds when needed.
New Feature
USB Host Port offers a new convenient way to transfer data from the M200 to a PC. By
using a standard USB Flash Drive to transfer traces, the user no longer needs a USB Cable,
ActiveSync or a Compact Flash reader. Using the Tools in the M200 File Manager, one or
more folders or files can be copied to a USB Flash Drive for transfer to a PC. Thousands of
files will fit on a 64 MB or larger USB Flash Drive.
Features
Applications
•• Handheld, 0.9 kg (2 lb)
•• 22 dB (MM), 26 dB (SM) dynamic range
•• Integrated VFL (650 nm)
•• Tool-free, switchable adapters
•• Transflective (indoor/outdoor) touchscreen display
•• USB Host and Function Ports
•• Tier 2 testing of premises networks
•• FTTX PON certification and
troubleshooting
•• Fast fault location
•• Splice verification
•• Network documentation
Ordering Information
Model
M200-00-0900PR
M200-11-0900PR
M200-12-0900PR
Description
850/1300nm multimode and 1310/1550nm single-mode OTDR
1310/1550nm single-mode OTDR
850/1300nm multimode OTDR
Test Port Adapters
(1) ST, (2) SC, and (1) FC *
SC and FC *
ST and SC *
* LC test port adapters are available (order separately).
NOTES:
1. All models include a rugged, soft-sided carry case with shoulder strap, 110/220 VAC power adapter with country-specific power cord, and user guide.
2. M200 Standard OTDR supported languages: English, French, German, Italian, Portuguese and Spanish. For Chinese/Taiwanese, Japanese, or Korean
models part numbers, please contact Noyes.
© 2006-2009, AFL Telecommunications, all rights reserved. M200-00-2000 Revision C, 2009-09-29
Specifications are subject to change without notice.
13
M200 Handheld OTDR in a Hard Case
The Noyes M200 OTDR is also available in a tough injection molded ABS carrying case.
The rugged transit case has a full length hinge, padlock loops, secure snap latches and
an O-ring seal to protect the contents from dust and water. In addition to the OTDR, the
custom case has room for cleaning products, launch and receive rings, documentation
and more. Order the Hard Case alone or with one of the M200 configurations. Add test
accessories such as fiber rings and cleaning kits to be ready to clean and test fiber optic
networks.
M200 Hard Case Ordering Information
M200 OTDR with standard accessories
The M200 Hard Case option should be specified when ordering the M200 OTDR. For the
M200 OTDR in a Hard Case ordering information, refer to the table below.
Model Number
Description
1400-01-0075PZ
Hard Case for M200
M200-00-0903PR
850/1300nm multimode and 1310/1550nm single-mode M200 OTDR in Hard Case
M200-11-0904PR
1310/1550nm single-mode M200 OTDR in Hard Case
M200-12-0902PR
850/1300nm multimode M200 OTDR in Hard Case
NOTE: Fiber rings and cleaning supplies are not included with the M200 in the Hard Case option, they must be purchased separately. To order fiber rings or
cleaning supplies with your M200, refer to the ‘Accessories Ordering Information’ table below.
Accessories Ordering Information
M200 OTDR with standard and optional accessories
Model Number
Fiber Rings
Description
FR1-M5-150-x1-x2
Standard, 1 fiber, 50/125 mm multimode, 150m
FR1-L5-150-x1-x2
Standard, 1 fiber, Laser Optimized, 50 mm multimode, 150m
FR1-M6-150-x1-x2
Standard, 1 fiber, 62.5/125 mm multimode, 150m
FR1-SM-150-y1-y2
Standard, 1 fiber, single-mode, 150m
Cleaning Accessories
8500-20-0900
Wet Cleaning Kit (shown) for SC/FC/ST/LC connectors.
Includes:
•• 8500-10-0016MZ, Cletop-SB.
•• CCTS-25-0900MZ, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adapters). Blue (40 sticks per tube). Qty = 1 tube
•• CCTS-12-0900MZ, Connector Cleaning Tips for 1.25mm ferrule in adapters or
sockets (LC, MU in adapters). Green (40 sticks per tube). Qty = 1 tube
•• FCC2-00-0900, optical quality Cleaning Fluid for fiber connector end faces.
8500-20-0901
Dry Cleaning Kit
Includes:
•• 8500-10-0016MZ, Cletop -SB.
•• 8500-10-0024MZ, ACT-01 2.5mm adapter cleaning tips (Qty = 200).
8500-05-0001MZ
One-Click Cleaner SC
8500-05-0002MZ
One-Click Cleaner LC/MU
NOTE: When ordering Fiber Rings, specify connector types (x1, x2, y1,y2)
© 2006-2009, AFL Telecommunications, all rights reserved. M200-00-2000 Revision C, 2009-09-29
Specifications are subject to change without notice.
14
M200 Handheld OTDR
Specifications
OTDR Specifications
Multimode
Single-mode
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1:2007-03
Center Wavelengths
850/1300 nm
1310/1550 nm
Wavelength Tolerance
± 20/± 30 nm
± 20/± 30 nm
Dynamic Range (SNR = 1)
22 dB
26 dB
Event Dead Zone 1
1.5 m
1.5 m
Attenuation Dead Zone 2
9m
9m
Pulse Widths 3
10, 30, 100, 300 ns, 1, 3 µs
10, 30, 100, 300 ns, 1, 3, 10 µs
Range Settings
250 m to 32 km
250 m to 208 km
Sampling Points
Up to 16,000
Up to 16,000
Min. Data Point Spacing
0.25 m
Group Index of Refraction (GIR)
1.4000 to 1.6000
Distance Uncertainty (m)
± (1 + 0.005% x distance + data point spacing)
Linearity
± 0.05 dB/dB (typical)
Trace File Format
Bellcore GR-196 Version 1.1
Trace File Storage Medium
Internal non-volatile memory, removable Compact Flash Card (not included), and USB Flash Drive
Trace File Storage Capacity
> 100 internal; thousands on Compact Flash or USB Flash Drive
Trace File Transfer to PC
Visual Fault Locator Specifications
USB Flash Drive Type 1.1, Compact Flash or Mini USB Cable with ActiveSync
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11; IEC 825-1:1993, 60825-1:2007-03
Wavelength
650 nm
Output Power (nominal)
General Specifications
0.8 mW
Size (in boot)
23 x 11 x 7 cm (8.8 x 4.3 x 2.8 inches)
Weight
0.9 kg (2 lb)
Operating Temperature
-10 to +50 °C
Storage Temperature
-20 to +60 °C
Relative Humidity
0 to 95% RH (non-condensing)
Power
Removable Li-Ion or 110/220 VAC power adapter
Battery Life4
6 hours
Recharge Time 4 & 5
3 hours
NOTES:
1.Typical distance between the two points 1.5 dB down each side of a reflective spike caused by a -40 dB (Multimode) or -45 dB (single-mode) event using 10 ns pulse width.
2.Typical distance from event location to point where trace is within 0.5 dB of backscatter.
3.3 µs pulse width not available at 850 nm.
4. New battery.
5. Typical, from fully discharged to fully charged state, unit may be operating.
All specifications are subject to change.
All specifications valid at 23°C ± 2°C (73.4°F ± 3.6°F) unless otherwise specified.
© 2006-2009, AFL Telecommunications, all rights reserved. M200-00-2000 Revision C, 2009-09-29
Specifications are subject to change without notice.
15
OFL280 Handheld FTTx OTDR
Installation (Live Fiber) and Construction
Models
The Noyes OFL280 from AFL Telecommunications is a singlemode OTDR offered in two FTTx-optimized models. The
‘installation and repair’ model can operate at three wavelengths
(1310/1550/1625 nm) on dark fibers but automatically switches
to a filtered, 1625 nm only mode if a live fiber is detected. In
addition, the test port is equipped with a PON power meter,
which allows the OFL280 to detect live FTTx fibers, measure
FTTx network power levels, and fault-locate live FTTx fibers with
a single OTDR to network connection and a single automated
test. A conventional three-wavelength (1310/1490/1550 nm)
‘construction’ model is also available to certify or fault-locate dark
fibers in FTTx or other networks.
Both OFL280 models can operate in Full Auto, Real-Time, or
Expert (manual) modes, and offer precision event analysis, an
optical power meter, laser source, 12-hour battery life, internal
data storage, and USB connectivity. OTDR and OPM test ports
are equipped with tool-free adapters, which can be changed in
seconds.
Results are saved as industry standard .SOR files, which can
be transferred to a PC for viewing, printing, and analyzing with
supplied Windows® compatible software.
Applications
Features
•• Test dark fibers at up to three wavelengths
•• Test live FTTx fibers at 1625 nm
•• Measure splice, connection, and end-to-end loss
•• Measure connection reflectance
•• Measure FTTx downstream power levels at 1490 and 1550 nm
•• Troubleshoot splice trays, terminals, and patch panels using the
VFL
•• Locate fiber ‘macro’ bends
•• Trace fibers up to 5 km using the VFL
•• Measure end-to-end loss using the OLS and OPM
•• Handheld, 0.8 kg (1.7 lb)
•• 1.3 m event dead zone
•• 30 dB (28 dB @ 1625 nm) dynamic range
•• FTTx construction model (OFL280-102) includes:
– 1310/1490/1550 nm
•• FTTx installation model (OFL280-103) includes:
– 1310/1550/1625 nm
– PON power meter
– Live fiber filter at 1625 nm
•• OPM, OLS, and VFL (650 nm)
•• Internal memory (> 1,000 trace files)
•• 3.5-inch, indoor/outdoor LCD display
•• 12-hour, rechargeable Li-Ion battery
•• USB port for PC connection
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. OFL2-28-2000 Revision 1F, 2009-03-24
Specifications are subject to change without notice.
16
OFL280 Handheld FTTx OTDR
Ordering Information
Two OFL280 models are available as indicated below:
Model
WAVELENGTHS
Description
OFL280-102
1310/1490/1550 (nm)
FTTx construction OTDR
Measures loss at the (3) wavelengths used in FTTx PON networks.
OFL280-103
1310/1550/1625 (nm)
FTTx installation (live fiber) OTDR
Includes filter to test live FTTx fibers @ 1625 nm, and a PON power meter
to measure downstream (1490/1550 nm) power levels on FTTx networks.
Note: All OFL280 models come with a carry case, (1) SC adapter for the OTDR/OLS port, (1) 2.5 mm Universal adapter
for the OPM port, (1) 2.5 mm Universal adapter for the VFL port, USB cable (connects with normal (Type A) USB port on
your PC), AC power adapter with a country specific power cord, and a user guide.
When placing an order, please specify model, OTDR port ferrule type, and language using the following part number format.
Example: OFL280-102U-ENG
OFL280
MMM
F
LLL
Language (LLL)
ENG = English
Model (MMM)
102
103
OTDR port ferrule (F)
A = APC
U = UPC
OFL280-102 FTTx Construction OTDR
OFL280-103 FTTx Installation OTDR
Visual Fault Locator (650 nm)
Visual Fault Locator (650 nm)
OFL280 OTDR
OFL280 OTDR
Optical Power Meter
Dark Fiber OTDR (1310/1490/1550 nm)
Laser Source (1310/1490/1550 nm)
Optical Power Meter
Dark Fiber OTDR (1310/1550/1625 nm)
Live Fiber OTDR (filtered 1625 nm)
PON Power Meter (1490/1550 nm)
Laser Source (1310/1550/1625 nm)
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. OFL2-28-2000 Revision 1F, 2009-03-24
Specifications are subject to change without notice.
17
OFL280 Handheld FTTx OTDR
Specifications
(All specifications valid at 25°C unless otherwise specified)
OTDR
Optical Power Meter
Emitter Type
Laser
Calibrated Wavelengths
1310, 1490, 1550, 1625, 1650 nm
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Detector Type
InGaAs
Measurement Range
+23 to - 50 dBm
Fiber Type
Single-mode
Tone Detect Range
+3 to -35 dBm
Available Wavelengths
1310/1490/1550/1625 nm
Wavelength ID Range
+3 to -35 dBm
Wavelength Tolerance
±20/±20/±20/±10 nm
Accuracy 1
± 0.25 dB
Dynamic Range (SNR=1)
30/30/30/28 dB
Resolution
0.01 dB
Event Dead Zone 1
1.3 m
Measurement Units
dBm or watts
Attenuation Dead Zone @ 5ns 2 Typical 5.0 m, maximum 6.0 m
Pulse Widths
5, 10, 30, 100, 300 ns, 1, 3, 10 µs
Range Settings
250 m to 256 km
Data Points
Up to 16,000
Data Point Spacing
12.5 cm (range < 4 km),
Range/16000 (range > 4 km)
Group Index of Refraction (GIR)
1.4000 to 1.6000
Distance Uncertainty (m)
± (1 + 0.005% x distance + data point spacing)
Trace File Format
Bellcore GR-196 V.1.1
Trace File Storage Medium
Internal memory (>1000 traces)
Data Transfer to PC
USB cable
OTDR Modes
Full Auto, End Locate, Expert, Live
1. At calibration wavelengths, and power level of approximately -10 dBm.
laser Source
1. Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
2. Typical distance from event location to point where trace is within 0.5 dB of
backscatter.
Emitter type
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Fiber type
Single-mode
Available Wavelengths (nm)
1310/1490/1550 or 1310//1550/1625
Wavelength Tolerance
± 20, ± 10 nm @ 1625 nm
Spectral Width (FWHM)
5 nm (maximum)
Internal Modulation
1 kHz, 2 kHz, CW
Wavelength ID (one, two, or
three wavelengths)
Compatible with Noyes Optical Power Meters and
Light Sources
Output Power Stability
< ± 0.25 dB after 15 min
Output Power
– 3 dBm
Visual Fault Locator
PON POWER METER
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Calibrated Wavelengths
1490, 1550 nm
Detector Type
InGaAs
Isolation
> 40 dB
Wavelength
650 nm
Measurement Range
+23 to – 50 dBm
Output Power (nominal)
0.8 mW into SMF-28
Accuracy 1
± 0.5 dB
Resolution
0.01 dB
Measurement Units
dBm or watts
General
1. At calibration wavelengths, and power levels of approximately -5 dBm for
1550 nm and -10 dBm for 1490 nm.
Size (in boot)
19 x 11.2 x 4.7 cm (7.5 x 4.4 x 1.9 in)
Weight
0.8 kg (1.7 lb)
Operational Temperature
-10 to +50°C, 0 to 95% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 95% RH (non-condensing)
Power
Rechargeable Li-Ion or AC adapter
Battery Life
(backlight ON in OTDR mode)
12 hours
Display
LCD, 320 x 240, 3.5 inch (89 mm), color,
transflective
OTDR and OPM Ports
Switchable, see web site or contact AFL for
available adapter types
© 2008-2009, AFL Telecommunications, all rights reserved. OFL2-28-2000 Revision 1F, 2009-03-24
Specifications are subject to change without notice.
18
OFL 250 Handheld OTDR
The Noyes OFL 250 from AFL Telecommunications is a single-mode OTDR with an
integrated Optical Power Meter (OPM), Laser Source (OLS), and Visual Fault Locator (VFL)
in a handheld package weighing only 0.8 kg (1.7 lb). With short dead zone and mid-range
dynamic range performance, the OFL 250 is ideal for testing optical fibers in service
provider metro areas and FTTx networks.
The OFL 250 provides automatic and manual setup, precision event analysis, multiplewavelength testing, a 12-hour battery life, internal data storage, and USB connectivity.
OTDR and OPM test ports are equipped with tool-free adapters, which can be changed in
seconds.
Results are saved as industry standard .SOR files, which can be transferred to a PC for
viewing, printing, and analyzing with the supplied Windows® compatible software.
Features
• Handheld, 0.8 kg (1.7 lb)
• Multiple-wavelength single-mode OTDR
• 1.5 m (typ.) event dead zone
• 26 dB dynamic range
• Integrated OPM, OLS, and VFL (650 nm)
• Tool-free, switchable adapters for OTDR & OPM ports (FC, SC, ST, LC, E2000 are available)
• Bellcore (GR-196) .SOR file format
• Rechargeable (> 12 hours) Li-Ion battery or AC power
• 3.5-inch, indoor/outdoor LCD
• Windows® compatible software to view, print, and archive test record
• Mini USB Port (connect to PC with cable)
Ordering Information
Model Number
Description
Wavelengths
OFL2-26-0910PR
OFL 250 Single-mode OTDR
1310/1550 nm
OFL2-26-0924PR
OFL 250 Single-mode OTDR
1310/1550/1625 nm
Note: All OFL 250 models come with: a carry case, SC and FC adapters for the OTDR/OLS port, 2.5mm
Universal adapters for the OPM and VFL ports, USB cable (connects with normal (Type A) USB port on your PC),
AC power adapter, country-specific power cord, and a user guide.
Continued on the next page
© 2007-2009, AFL Telecommunications, all rights reserved. OFL2-26-2000 Revision D, 2009-03-24
Specifications are subject to change without notice.
19
OFL 250 Handheld OTDR
Specifications
OTDR
Optical Light Source
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Fiber Type
Single-mode
Center Wavelengths
1310/1550/1625 nm
Wavelength Tolerance
± 20 / ± 20 / ± 10 nm
Wavelength Tolerance
± 20/± 20/± 10 nm
Spectral Width (FWHM)
5 nm (max)
Dynamic Range (SNR=1)
26/26/26 dB
Internal Modulation
1 kHz, 2 kHz
Event Dead Zone
1.5 m
Wavelength ID
Compatible with Noyes Optical Power Meters &
Light Sources
1
Attenuation Dead Zone @ 5ns 2 Typ.6.0 m, max. 6.5 m
Emitter Type
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Fiber Type
Single-mode
Center Wavelengths
1310 / 1550 / 1625 nm
Pulse Widths
5, 10, 30, 100, 300 ns, 1, 3, 10 µs
Output Power Stability
< ± 0.25 dB after 15 min
Range Settings
250 m to 256 km
Output Power
– 3 dBm
Data points
Up to 16,000
Data Point Spacing
12.5 cm (range < 4 km),
Range/16000 (range > 4 km)
Group Index of Refraction (GIR)
1.4000 to 1.6000
Emitter type
Laser
Distance Uncertainty (m)
± (1 + 0.005% x distance + data point spacing)
Safety Class
Trace File Format
Bellcore GR-196 V.1.1
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Trace File Storage Medium
Internal memory (>1000 traces)
Wavelength
650 nm
Data Transfer to PC
USB cable
Output Power (nominal)
0.8 mW into SMF-28
OTDR Modes
Full Auto, End Locate, Expert, Live
Visual Fault Locator
1. Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
General
Size (in boot)
19 x 11.2 x 4.7 cm (7.5 x 4.4 x 1.9 in)
2. Typical distance from event location to point where trace is within 0.5 dB of
backscatter.
Weight
0.8 kg (1.7 lb)
Operational Temperature
-10 to +50°C, 0 to 95% RH (non-condensing)
Optical Power Meter
Storage Temperature
-20 to +60°C, 0 to 95% RH (non-condensing)
Calibrated Wavelengths
1310, 1490, 1550, 1625 nm
Power
Rechargeable LiIon or AC adapter
Detector Type
InGaAs
Measurement range
+23 to - 45 dBm
Battery life
(backlight ON in OTDR mode)
> 12 hours
Tone detect range
+3 to -35 dBm
Wavelength ID range
+3 to -35 dBm
Display
LCD, 320 x 240, 3.5 inch (89 mm) , color,
transflective
Accuracy
± 0.25 dB
OTDR and OPM ports
Resolution
0.01 dB
Switchable. See website or contact AFL for
available adapter types.
Measurement units
dB, dBm, mW, nW
© 2007-2009, AFL Telecommunications, all rights reserved. OFL2-26-2000 Revision D, 2009-03-24
Specifications are subject to change without notice.
20
OTDR Fiber Rings
Measuring an insertion loss of the near-end and / or far-end connection of a fiber optic
link with an OTDR requires a launch and / or receive test cable. A launch cable, which
connects the OTDR to the link under test, reveals the insertion loss and reflectance of the
near-end connection. A receive cable, which connects to the far-end of the link, reveals
the insertion loss and reflectance of the far-end connection. Launch and receive test
cables can range from 150 m to 1 km (or longer) in length. Because very long test cables
are impractical to transport and use, Noyes offers coiled lengths of 50 mm multimode,
62.5 mm multimode, or single-mode fiber packaged in compact rings.
Fiber Ring, MM - 150 m
Fiber Rings of 150 m of fiber are ideal for premises fiber network test applications. Fiber
Rings of 500 m and 1 km of single-mode fiber are designed for broadband, long-haul fiber
network test applications.
Fiber Ring Models
Fiber Ring, SM - 1000 m
Model
Configuration
Fiber Type
Fiber Length
FR1-M5-150- x1- x2
Standard, one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-L5-150-x1-x2
Standard, one fiber, Laser Optimized
Multimode, 50 mm
150m (492 ft)
FR1-M6-150- x1- x2
Standard, one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-150- y1- y2
Standard, one fiber
Single-mode
150 m (492 ft)
FR1-SM-500- y1- y2
Standard, one fiber
Single-mode
500m (1640 ft)
FR1-SM-1000- y1- y2
Standard, one fiber
Single-mode
1000m (3280 ft)
FR3-M5-x1-MTRJ
MT-RJ near-end, A and B fibers
Multimode, 50 mm
150 m (492 ft)
FR3-M6-x1-MTRJ
MT-RJ near-end, A and B fibers
Multimode, 62.5 mm
150 m (492 ft)
FR3-SM-x1-MTRJ
MT-RJ near-end, A and B fibers
Single-mode
150 m (492 ft)
FR1-M5-x1-E2000
E2000 to ST, SC, FC, etc., one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-M6-x1-E2000
E2000 to ST, SC, FC, etc., one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-y1-E2000
E2000 to ST, SC, FC, etc., one fiber
Single-mode
150 m (492 ft)
FR1-M5-E2000-E2000
E2000 to E2000, one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-M6-E2000-E2000
E2000 to E2000, one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-E2000-E2000
E2000 to E2000, one fiber
Single-mode
150 m (492 ft)
x1, x2 — connectors for multimode cables, specify type [ST, SC, ASC (angled SC), FC, AFC (angled FC), LC]
y1, y2 — connectors for single-mode cables, specify type [ST, SC, ASC (angled SC), FC, AFC (angled FC), LC]
Other connector types, fiber types, and fiber lengths will be quoted upon request.
Fiber Ring, Laser Optimized
Continued on the next page
© 2008, AFL Telecommunications, all rights reserved. FR00-00-2000 Revision 1A, 8.25.08
Specifications are subject to change without notice.
21
OTDR Fiber Rings
How to Generate a Baseline Trace Using Fiber Rings
•• Use the Fiber Ring as a launch cable.
Connect the Fiber Ring between your OTDR and the fiber link under test. This will allow
you to measure the loss of the near-end connection.
•• Use the Fiber Ring as a receive cable.
Cconnect the Fiber Ring to the far-end connector of your fiber link under test. This will
allow you measure the loss of the far-end connection.
•• By using Fiber Rings as both launch and receive cables, as shown in the diagram below,
you can measure total insertion loss of the fiber link under test.
fiber ring - launch cable
2
6
7
fiber link under test
fiber ring - receive cable
fiber ring connector
1
4
OTDR port
fusion splice
OTDR
3
5
8
near-end connection
far-end connection
end of receive cable
Example OTDR Test Configuration With Launch And Receive Cables
OTDR port
1
8
end of receive cable
near-end connection
3
6
fiber link under test
fiber ring - launch cable
2
5
far-end connection
fusion splice
4
7
fiber ring - receive cable
OTDR Trace Made Using Launch And Receive Cables
© 2008, AFL Telecommunications, all rights reserved. FR00-00-2000 Revision 1A, 8.25.08
Specifications are subject to change without notice.
22
C860 QUAD OTDR and Certification Test Kit
Features
The Noyes C860 QUAD Certification and OTDR Test Kit from AFL Telecommunications
includes one handheld C840 QUAD OLTS Tester and one C850 QUAD OTDR/OLTS with
built-in auto test functionality. With this kit, technicians can troubleshoot and perform both
Tier 1 and Tier 2 certification tests of MM and SM fiber networks, store results and create
professional test reports.
The C850 is both a QUAD Certification Tester and full-featured QUAD OTDR in a compact
case with a large transflective touch screen display suitable for both indoor and outdoor
operation. The C850 features single-mode and multimode OTDR capabilities, both singlemode and multimode Optical Light Sources (OLS), Visual Fault Locator (VFL, 650 nm), and
an Optical Power Meter (OPM). As an OTDR, the C850 supports Full Auto, Expert (manual)
and Real-Time test modes, simultaneous dual and single wavelength testing, and Event
and Pass/Fail analysis based on default or user-defined thresholds.
The C840 QUAD Certification Tester includes VFL, OPM, and both single-mode
(1310/1550 nm) and multimode (850/1300 nm) OLS. The C840 may be used alone as a
traditional power meter or light source to measure fiber loss or as a visual fault locator to
find fiber breaks.
•• OTDR dynamic range:
- 22 dB (MM)
- 26 dB (SM)
•• Integrated OPM, OLS, and VFL (650 nm)
•• OLS sources:
- LED - 850/1300 nm
- Laser - 1310/1550 nm
•• Full Auto, Expert, Real-Time OTDR test
modes
•• Large transflective (indoor/outdoor) touch
screen display
•• Tool-free, switchable test port adapters
•• Rechargeable Li-Ion battery (> 8 hours)
or AC power
•• USB host and function ports
•• Bellcore (GR-196) .SOR file format
•• Internal (1000s tests) and USB storage
•• Wave ID detect if used with Noyes Wave
ID series light sources
•• Windows® compatible software
Applications
•• Tier 1 and Tier 2 testing of premise
networks
•• Bi-directional two fibers and single fiber
test capable
•• Perform Pass/Fail Event and Link
measurements
•• Find faults using integrated Visual Fault
Locator
•• Splice verification
•• Measure loss and length of fiber links
•• Certify fibers using Pass/Fail criteria of
industry standards, applications and
user-defined thresholds
•• Create professional certification reports
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. C860-00-2000 Revision 1F, 2009-10-12
Specifications are subject to change without notice.
23
C860 QUAD OTDR and Certification Test Kit
The C840 and C850 can be used together to perform Tier 1 dual
wavelength MM (850/1300 nm) and SM (1310/1550 nm) auto
loss tests of one or two fibers in one or both directions as well
as measure both loss and length of the fibers and compare to
industry standards (TIA/ISO/EN), applications and user-defined
thresholds values to certify the fibers. Either unit can be identified
as the Main or Remote.
The user may test two fibers at two wavelengths bi-directionally
and store the results into the main unit. Featuring rich file naming,
the Job setup wizard allows the user to define both the cable and
fiber end locations, creating easily identifiable trace files, which
are managed into Job and Cable folders.
Ordering Information
When placing an order, select options as follows: Model, Optical Configuration, Language, and Case.
Example: C860 — 100 — LP1 — H5
C860
NNN
LLL
CC
Case (CC)
H2 = Hard and soft case with SC-LC test
and cleaning accessories
H5 = Hard and soft case with SC-ST test
and cleaning accessories
Language (LLL)
LP1 = Language Pack: English, German,
French, Spanish, Italian, Portuguese
JPN = Japanese/English
CHI = Chinese/Taiwanese/English
RUS = Russian/English
KOR = Korean/English
ARA = Arabic/English
Model
C860
Optical Configuration (NNN)
100 = QUAD 850/1300 nm MM and 1310/1550 nm SM
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. C860-00-2000 Revision 1F, 2009-10-12
Specifications are subject to change without notice.
24
C860 QUAD OTDR and Certification Test Kit
Ordering Information (continued)
Each kit includes one handheld C840 QUAD Certification Tester, one compact C850 QUAD OTDR/OLTS, USB Flash drive, PC software for
OTDR trace analysis and certification or OPM loss reporting, (2) AC adapters, switchable test ports adapters, and accessories (see table
below).
Model
carry Case
Fiber
Rings1
Test
Cords2 OTDR/OLS
Adapters
OPM
Cleaning Products
VFI
C860-100-LP1-H2
Soft and hard cases
SC/LC
SC/LC
SC, ST, LC
SC, 2.5, 1.25mm
2.5, 1.25mm One-Click Cleaner SC/ST/FC, 2.5mm
One-Click Cleaner LC, 1.25mm
Cletop - SB white tape
C860-100-LP1-H5
Soft and hard cases
SC/ST
SC/ST
SC, ST, LC
SC, 2.5, 1.25mm
2.5, 1.25mm One-Click Cleaner SC/ST/FC, 2.5mm
Cletop - SB white tape
1 (2) each - 150m (62.5µm, 50µm, SM)
2 (4) each - 150m (62.5µm, 50µm, SM)
C860—100—LP1—H2 (or H5) Kit Contents
Optional OTDR and Cleaning Accessories
Item
Description
Model Number
Description
C850
QUAD OTDR/Auto Test Certification Tester
FR1-SM-150-SC-FC
Fiber ring, single-mode, SC/FC, 150 m
C840
QUAD Auto Test Certification Tester
FR1-SM-150-SC-LC
Fiber ring, single-mode, SC/LC, 150 m
Adapters
OTDR and OLS ports — SC, ST, LC
OPM ports — SC, 1.25 and 2.5mm Universal
VFI ports — 1.25 and 2.5mm Universal
FR1-M6-150-SC-ST
Fiber ring, multimode, 62.5mm, SC/ST, 150 m
Fiber Rings (6)
150 m (62.5mm, 50mm, SM)
Jumpers (12)
2 m (62.5mm, 50mm, SM)
Miscellaneous
Accessories
Mandrels (2) — 62.5mm, 3mm jacket
Mandrels (2) — 50mm, 3mm jacket
Stylus pens for touch screen
USB thumb drive, 1G
USB to mini-USB cable
Small plastic parts box (2) to store adapter caps and mandrels
AC adapter (2), specify country of use
Cleaning
Accessories
(2) One-Click Cleaner SC/ST/FC, 2.5mm
One-Click Cleaner LC/MU, 1.25mm (H2 kit only)
Fiber ring, multimode, 62.5mm, SC/LC, 150 m
FR1-M5-150-SC-ST
Fiber ring, multimode, 50mm, SC/ST, 150 m
FR1-M5-150-SC-LC
Fiber ring, multimode, 50mm, SC/LC, 150 m
FR1-L5-150-SC-LC
Fiber ring, laser optimized, multimode, 50mm, SC/LC, 150 m
FR1-L5-150-SC-SC
Fiber ring, laser optimized, multimode, 50mm, SC/SC, 150 m
FR1-SM-500-SC-LC
Fiber ring, single-mode, SC/LC, 500 m
FR1-SM-500-SC-SC
Fiber ring, single-mode, SC/SC, 500 m
FR1-SM-500-SC-FC
Fiber ring, single-mode, SC/FC, 500 m
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
8500-05-0001MZ
One-Click Cleaner SC/ST/FC
8500-05-0002MZ
One-Click Cleaner LC/MU
8500-10-0017MZ
Replacement tape for Cletop (white)
Note: 1000 m single-mode fiber rings are also available.
Cletop SB white tape
Cases
FR1-M6-150-SC-LC
Hard transit case — holds C850, C840, and above accessories
Soft case for C850
Documentation
User guides and quick reference guides
Report Software PC software and user guide
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. C860-00-2000 Revision 1F, 2009-10-12
Specifications are subject to change without notice.
25
C860 QUAD OTDR and Certification Test Kit
Specifications
(All specifications valid at 25°C unless otherwise specified)
OTDR
Multimode
Single-mode
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Center Wavelengths
Wavelength Tolerance
850/1300 nm
1310/1550 nm
± 20/30 nm
± 20/30 nm
22 dB
26 dB
Dynamic Range (SNR = 1)
10, 30, 100, 300 ns; 1, 3, 10 ms
Pulse Widths
Range Settings
250 m to 64 km
Sampling Points
250 m to 208 km
0.25 m
Group Index of Refraction (GIR)
Safety Class
+6 to -60 dBm
Accuracy 1
±0.25
2
dB, dBm, mW
Yes (to -47 dBm)
Set Reference
Yes
Data Storage
Yes
Tone Detection
Yes (to -47 dBm)
± (1 + 0.005% x distance + data point spacing)
general
C850 OTDR
C840 Tester
± 0.05 dB/dB
Test Modes
OTDR (Full Auto, Expert,
Real-Time), Auto Test, OPM,
OLS, VFL
Auto Test,
OPM, OLS, VFL
SR-4731 (GR-196-CORE
Appendix A, B; SR-4731)
N/A
1 Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
2 Typical distance from event location to point where trace is within 0.5 dB of
backscatter caused by a -45 dB event using 10 ns pulse width.
3 Does not include GIR uncertainty.
Emitter Type
Measurement Range
1.4000 to 1.6000
Linearity
Light Source
Available Wavelengths
InGaAs 2mm
1 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
2 Automatic wavelength identification and switching when used with Noyes Wave
ID Series Light Sources.
Up to 16,000
Min. Data Point Spacing
850, 1300 1310, 1490, 1550, 1625 nm
Detector Type
Wavelength ID
9m
Attenuation Dead Zone 2
Calibrated Wavelengths
Measurement Units
1.5 m
Event Dead Zone 1
Distance Uncertainty (m) 3
Power Meter
Multimode port
850/1300 nm (nominal)
Single-mode port
1310/1550 nm (nominal)
LED
Laser
Trace File Format
Length Measurement Range
Data Storage
> - 20 dBm, 62.5µm
MM 1
0 dBm, 9µm SM
Stability (after 15
minutes warm up)
± 0.1 dB over 1 hour
± 0.07 dB over 1 hour
± 0.15 dB over 8 hours
Wave ID Transmit
Yes
Tone Generation
270 Hz, 330 Hz, 1 KHz, 2 kHz
USB flash drive (2.0)
Data Storage Capacity
USB
Tool Free Adapters
Modular cleanable SC/ST/LC
Weight
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Wavelength
650 nm
Output Power (nominal)
0.8 mW
23 x 11 x 7 cm
(8.8 x 4.3 x 2.8 in)
2.3 kg ( 5 lb)
0.9 kg (2 lb)
-10 to +50°C, 0 to 90% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
Battery Life 1
Recharge Time 2
Laser
27.4 x 19.3 x 7.1 cm
(10.8 x 7.6 x 2.8 in)
Operating Temperature
Power
Visual Fault Locator
Internal > 1000 fibers
Data Transfer to PC
Size
1 Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped
jumper is used instead of a 62.5 µm mandrel-wrapped jumper.
Emitter Type
Internal flash memory
Downloadable from unit directly to PC
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
Output Power
5 km (MM);
200 km (SM)
Display
Rechargeable Li-Ion or AC power adapter
> 8 hours continuous testing
4 hours
16.51 cm (6.5 in),
color, transflective
9.65 cm (3.8 in),
color, transflective
1 Typical, depending on display brightness.
2 Typical, from fully discharged to fully charged state, unit may be operating.
External battery charger available.
© 2008-2009, AFL Telecommunications, all rights reserved. C860-00-2000 Revision 1F, 2009-10-12
Specifications are subject to change without notice.
26
FTK Pro Installer Kit
The Noyes FTK Pro Installer Kit from AFL Telecommunications
provides a wide selection of fiber optic testing, cleaning, and
inspection equipment to enable technicians to install and maintain
fiber optic networks. Available with multimode and single-mode
test equipment, the kit also includes a broad array of cleaning and
inspection equipment in a convenient tough injection-molded ABS
carrying case. The Pro Installer Kit is ideal for TIA Tier 1 and Tier 2
testing of premises (building and campus) networks or certification
and troubleshooting of FTTx PON networks.
Kit Contents
Item
M200
OPM5-2D
OLS4
OFS300-200
Features
•• Clean, inspect, and test fiber optic networks
•• Multimode and single-mode fiber ready
•• Verify integrity of installed fiber networks
•• Software to present network owners with written proof of a quality
installation
•• Convenient rugged hard carry case
Fiber Rings
(1 each)
Applications
•• Tier 1 and Tier 2 testing of premise networks
•• FTTx PON certification and troubleshooting
•• Fast fault location
•• Splice verification
•• Network documentation
Adapters
Jumpers,
2 meters in
length (2 each)
Ordering Information
part number
Description
FTK1-01-0900PR
See Kit Contents Table
Description
Quad OTDR, 850/1300 nm MM, 1310/1550 nm SM
Optical Power Meter (Wave ID, Set Reference, Data Storage)
Optical Light Source (LED and Laser)
Optical Fiber Scope (200x)
FR1-L5-150-SC-ST
(50/125 OM3 550 Laser Optimized)
FR1-L5-150-SC-LC
(50/125 OM3 550 Laser Optimized)
FR1-L5-150-ST-LC
(50/125 OM3 550 Laser Optimized)
FR1-M6-150-SC-ST (62.5/125)
FR1-M6-150-SC-LC (62.5/125)
FR1-M6-150-ST-LC
(62.5/125)
FR1-SM-150-SC-ST (SM)
FR1-SM-150-SC-LC (SM)
FR1-SM-150-ST-LC
(SM)
SC, ST, LC for the OTDR/OLS ports (2 each)
SC, ST, LC for the OPM Unit
2.5mm and 1.25mm Universal for OFS and for VFL on OTDR
SC-ST
(50/125 OM3 550 Laser Optimized)
SC-LC
(50/125 OM3 550 Laser Optimized)
SC-ST
(62.5/125)
SC-LC
(62.5/125)
SC-ST
(SM)
SC-LC
(SM)
Bulkheads
SC/SC, ST/ST, LC/LC
(mating adapters)
FiberWipes™ Mini-tub
Cletop -SB with white tape
Cletop replacement tape (white)
FCC2 Fiber Connector Cleaner
Cleaning Supplies
Connector Cleaning Tips (for cleaning in sockets):
2.5mm and 1.25mm
One-Click Cleaner SC/ST/FC
Miscellaneous
Accessories
Report Software
One-Click Cleaner LC/MU
(2) Mandrels: 62.5mm, 3mm jacket and 50mm, 3mm jacket
Stylus pen for the M200 touch screen
USB thumb drive, 1G
Plastic parts boxes to hold adapters (Qty 3)
Case to hold up to 12 jumpers (2 – 5 meters in length)
Windows® compatible software and user guide
© 2009, AFL Telecommunications, all rights reserved. FTK1-01-2000 Revision 1C, 2009-03-26
Specifications are subject to change without notice.
27
C880 QUAD Certification Test Kit
Features
•• Handheld, 0.9 kg (2 lb)
•• Integrated OPM, OLS, and VFL (650 nm)
•• OLS sources:
- LED - 850/1300 nm
- Laser - 1310/1550 nm
•• Dual-wavelength certification Pass/Fail
•• Two fibers bi-directional and single fiber
testing
•• Transflective (indoor/outdoor) touch
screen display
•• Tool-free, switchable test port adapters
•• Rechargeable Li-Ion battery (> 8 hours)
or AC power
•• USB host and function ports
•• Internal (1000s tests) and USB storage
•• Windows® compatible software
Applications
Combining two C840 Certification Testers, the Noyes C880 QUAD Certification Test Kit
from AFL Telecommunications is designed for testing and troubleshooting both multimode
and single-mode fiber links. Each tester includes an integrated Visual Fault Locator (VFL,
650 nm), both single-mode (Laser 1310/1550 nm) and multimode (LED 850/1300 nm)
Optical Light Sources (OLS), and an Optical Power Meter (OPM). Each tester may be used
alone as a traditional power meter, light source or visual fault locator.
In Auto Test mode, the user may perform certification tests to one of the industry cabling
standards (TIA, ISO, EN), one or more application standards, or a user-defined loss/length
limit. Certification reports may be generated based on the selected standards and rules
using PC reporting software. The transflective touch screen display of the C840 tester is
suitable for both indoor and outdoor operation. Thousands of test results may be stored
internally for transfer to a computer via a USB cable or a standard USB drive. Once test
data is transferred to a computer, the supplied Windows® compatible software allows
technicians to view, print, and generate professional certification reports.
•• Tier 1 testing of premise networks
•• Bi-directionally measure loss and length
of fiber links
•• Save time simultaneously testing two
fibers at two wavelengths
- MMF 850/1300 nm
- SMF 1310/1550 nm
•• Verify polarity
•• Certify SM and MM networks to industry
standards (ISO/TIA/EN) and applications
•• Find faults using integrated Visual Fault
Locator
•• Create and test to user defined rules
•• Review Pass/Fail feedback after each
test
•• Review fibers by cable and retest fiber
pairs if needed
•• Create professional certification reports
Continued on the next page
© 2008-2009, AFL Telecommunications, all rights reserved. C880-00-2000 Revision 1E, 2009-10-12
Specifications are subject to change without notice.
28
C880 QUAD Certification Test Kit
Ordering Information
Each C880 kit or C840 kit includes two (2) C840s or one (1) C840 Tester respectively, USB Flash drive, PC software for OTDR trace
analysis and certification or OPM loss reporting, AC adapters (two (2) with C880 kit, one (1) with C840 kit), switchable test ports adapters,
and accessories (see table below).
Model
carry Case
Test
Cords2
Adapters
Cleaning Products
OLS
OPM
VFI
SC, ST, LC
SC, 2.5, 1.25mm
2.5, 1.25mm
One-Click Cleaner SC/ST/FC, 2.5mm
One-Click Cleaner LC, 1.25mm
C880-100-LP1-S1
Soft case
SC/LC
C880-100-LP1-S2
Soft case
SC/ST
SC, ST, LC
SC, 2.5, 1.25mm
2.5, 1.25mm
One-Click Cleaner SC/ST/FC, 2.5mm
C840-100-LP1-S1
Soft case
—
SC, ST, LC
SC, 2.5, 1.25mm
2.5, 1.25mm
One-Click Cleaner SC/ST/FC, 2.5mm
C880–100–LP1–S1 (or S2) C880 Kit Contents
Optional Cleaning Accessories
Item
DESCRIPTION
Model Number
Description
C840
QUAD Auto Test Certification Tester (2 ea)
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
Adapters
OLS Ports — SC, ST, LC
OPM port — SC, 1.25 and 2.5mm Universal
VFI port — 1.25 and 2.5mm Universal
8500-05-0001MZ
One-Click Cleaner SC/ST/FC
8500-05-0002MZ
One-Click Cleaner LC/MU
8500-10-0017MZ
Replacement tape for Cletop (white)
Jumpers (12)
2 m (62.5 mm, 50 mm, SM)
Miscellaneous
Accessories
Mandrels (2) — 62.5mm, 3mm jacket
Mandrels (2) — 50mm, 3mm jacket
Stylus pens for touch screen
USB thumb drive -1G, USB to mini-USB cable
AC adapters (2), specify country of use
Cleaning Accessories (2) One-Click Cleaner SC/ST/FC, 2.5mm (S1 and S2 kit)
One-Click Cleaner LC/MU, 1.25mm (S1 kit only)
Cases
Soft case (2)
Report Software
PC software and user guide
When placing an order, select options as follows: Model, Optical Configuration, Language, and Case.
Example: C880 – 100 – LP1 – S1
C880
NNN
LLL
CC
Case (CC)
Model
C880
S1 = Soft case for C840 (two units) with SC-LC
test and cleaning accessories
S2 = Soft case for C840 (two units) with SC-ST
test and cleaning accessories
Optical Configuration (NNN)
100 = QUAD 850/1300 nm MM and 1310/1550 nm SM
Language (LLL)
LP1 = Language Pack: English, German,
French, Spanish, Italian, Portuguese
JPN = Japanese/English
CHI = Chinese/Taiwanese/English
RUS = Russian/English
KOR = Korean/English
ARA = Arabic/English
© 2008-2009, AFL Telecommunications, all rights reserved. C880-00-2000 Revision 1E, 2009-10-12
Specifications are subject to change without notice.
29
C880 QUAD Certification Test Kit
Specifications
(All specifications valid at 25°C unless otherwise specified)
General
Test Modes
Visual Fault Locator
Auto Test, OPM, OLS, VFL
Emitter Type
Laser
Length Measurement Range 5 km (MM); 200 km (SM)
Safety Class
Class II FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
USB flash drive (2.0)
Wavelength
650 nm
Downloadable from unit directly to PC
Output Power (nominal)
0.8 mW
Data Storage
Internal flash memory
Data Storage Capacity
Internal > 1000 fibers
Data Transfer to PC
USB
Tool Free Adapters
Modular cleanable SC/ST/LC
Light Source
Available Wavelengths
Size
23 x 11 x 7 cm (8.8 x 4.3 x 2.8 in)
Emitter Type
Weight
0.9 kg (2 lb)
Safety Class
Operating Temperature
-10 to +50°C, 0 to 90% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
Output Power
Power
Rechargeable Li-Ion or AC power adapter
Battery Life 1
> 8 hours continuous testing
Stability (after 15
minutes warm up)
Recharge Time 2
4 hours
Wave ID Transmit
Yes
Display
9.65 cm (3.8 in), color, transflective
Tone Generation
270 Hz, 330 Hz, 1 KHz, 2 kHz
Multimode port
850/1300 nm (nominal)
Single-mode port
1310/1550 nm (nominal)
LED
Laser
Class I FDA 21 CFR 1040.10 and 1040.11,
IEC EN60825-1: 2007-03
> - 20 dBm, 62.5 µm MM 1
0 dBm, 9 µm SM
± 0.1 dB over 1 hour
± 0.07 dB over 1 hour
± 0.15 dB over 8 hours
1 Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped
jumper is used instead of a 62.5 µm mandrel-wrapped jumper.
1 Typical, depending on display brightness.
2 Typical, from fully discharged to fully charged state, unit may be operating.
External battery charger available.
Power Meter
Auto Test Wavelengths
850/1300 nm (MM), 1310/1550 nm (SM)
Detector Type
InGaAs 2mm
Measurement Range
+6 to -60 dBm
Accuracy
1
±0.25
Measurement Units
dB, dBm, mW
Wavelength ID 2
Yes (to -47 dBm)
Set Reference
Yes
Data Storage
Yes
Tone Detection
Yes (to -47 dBm)
1 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
2 Automatic wavelength identification and switching when used with Noyes Wave
ID Series Light Sources.
© 2008-2009, AFL Telecommunications, all rights reserved. C880-00-2000 Revision 1E, 2009-10-12
Specifications are subject to change without notice.
30
Turbotest 500B
Optical Loss/Return Loss Test Sets
The Turbotest 500B Series offers the latest technology in a single fiber bi-directional
loss and return loss testing. The T500B is a handheld fiber optic test and measurement
instrument. It performs Optical Power, Optical Return Loss, and Optical Loss
measurements. Five compact models are available, including the three wavelength
(1310/1550/1625) T506B and (1310/1550/1490) T506B-FTTH. An optional dedicated
digital talk option is available for full time/full duplex communication between test
operators while testing other fibers in a bundle.
The T500B can store up to 1000 records (40 files) in any combination of its four
operating modes and if any configuration other than TRIPLE wavelength is selected. If
the configuration is TRIPLE wavelength, the T500B can store up to 500 records (40 files).
Stored test results can be transferred to a PC for a complete report generation.
Features
•• Rugged, handheld, designed for field use
•• Passive Optical Networks (PON) testing
•• Single fiber, bi-directional loss and return
loss testing at 1310/1490/1550 nm or
1310/1550/1625 nm
•• TRIPLE wavelength test mode
•• Talk Set option
•• Up to 1000 test records (40 files) storage
and download
•• Free Windows® compatible software to
view, print, and archive test records
•• Lithium-Ion or AC adapter
•• Cost-effective, easy to use
Ordering Information
Model
Includes
All T500B
models
(1) T500B, protective rubber boot, APC/
UPC test jumper, adapter cap, serial
cable, hex driver, screwdriver, mandrel,
AC adapter, PC software, user’s guide,
and carry case.
When ordering, specify connector type
after the model number, (e.g. T504B-Y-SC
is a 1310/1550/ Turbo with 1550 nm Talk
Set Option and a SC connector).
Powered by an internal rechargeable Lithium-lon battery, the T500B comes with protective
rubber boots, PC software and manual, AC adapter/charger, RS-232 serial cable, APC/UPC
reference cable, adapter cap, mandrel, screwdriver, hex screwdriver, warranty registration
card, user’s guide, and carry case.
Specifications
Model
T503B
Calibrated wavelengths (nm)
1310, 1550 1310, 1550
T504B
T505B
T506B
T506B-FTTH
1550, 1625 1310, 1550, 1310, 1550,
1625
1490
Output power (dBm)
-5
-5
-5
-5
-5
Emitter type
Laser
Laser
Laser
Laser
Laser
Safety class
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Detector type
InGaAs
InGaAs
InGaAs
InGaAs
InGaAs
Insertion loss measurement range
(dB)
45
45
45
45
45
+26 to -50
+26 to -50
+26 to -50
+26 to -50
Measurement range (dBm)
+6 to -70
Measurement units
dB, dBm, µW
ORL dynamic range (dB)
65
Available connector types
ASC or AFC
Power
Lithium-Ion or AC Adapter
Li-Ion battery pack charging temp.
-10 to +45°C
Li-Ion battery pack charging time will increase by 25% at a temperature below -5°C.
Do not charge the Li-Ion battery pack at a temperature above +45°C.
After the model number:
Add -T for 40 dB 1310 nm Talk Set option.
Add -Y for 40 dB 1550 nm Talk Set option.
Example: T506B-Y is 1310/1550/1625 Turbo with 1550nm Talk Set option.
T500B instruments are sold individually but normally used in pairs
© 2002-2009, AFL Telecommunications, all rights reserved. T50B-00-2000 Revision G, 2009-06-04Specifications are subject to change without notice.
31
OLTS 5 Optical Loss Test Set
The OLTS 5 Optical Loss Test Set series offers end-to-end single-mode testing at either
1310/1550 nm or 1550/1625 nm. The OLTS 5 may be operated in automatic or manual
test modes. In its “two-unit” automatic test mode, a pair of OLTS 5 test sets may be used
to measure the end-to-end, bi-directional insertion loss of a pair of single-mode fibers at
1310/1550 nm or 1550/1625 nm. Tests are started and controlled by the user from the
OLTS 5 configured as the Main unit. Test progress messages and results are displayed on
the Remote unit. Full test results can be reviewed and saved in the Main unit. Thresholds
may be set to provide Pass/Fail results. In its “single-unit” automatic test mode the OLTS 5
can measure bi-directional, dual-wavelength insertion loss of patch cords, or fiber optic
cables while they are still on the reel. In the manual operating mode individual OLTS 5 test
sets can operate either as an optical power meter (OPM) or dual-wavelength laser source.
Features
•• Handheld, rugged, lightweight
•• Integrated dual-wavelength laser source
and optical power meter
•• Automatic bi-directional, dualwavelength insertion loss measurement
•• Optical power meter and light source
manual test modes
•• Up to 1000 test records storage
•• Free Windows® compatible software to
view, print, and archive test records
•• 2 AA alkaline. Optional internally
recharged NiMH battery pack or AC
•• Cost-effective, easy to use
The OLTS 5 can store dual-wavelength, bi-directional insertion loss results for up to 1,000
fibers. Test results can be organized in up to 20 user-named files. Results are transferred
to a PC using the supplied serial cable or RS232 / USB adapter. Windows® compatible
software is provided to view, edit, and print test results. OLTS 5 units are sold individually
but normally used in pairs.
Specifications
Model
OLTS 5-3
Transmit port (laser source) specifications
1310/1550 ± 20 nm
Center wavelengths
OLTS 5-5
OLTS 5-6
1550/1625 ± 20 nm
1310/1550 ± 20 nm
Emitter type
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Output power into 9/125 SM fiber
-5 dBm (nominal)
Stability
Insertion loss and power
measurement resolution
± 0.1 dB, up to 8 hours ± 0.1 dB, up to 8 hours ± 0.1 dB, up to 8 hours
0.01 dB
-5 dBm (nominal)
0.01 dB
-5 dBm (nominal)
0.01 dB
Model
Includes
SC, FC, ST
SC, FC, ST
Available connector types
Receive port (optical power measurement) specifications
InGaAs
InGaAs
Detector type
All OLTS 5
models
(1) OLTS 5, (2) AA alkaline batteries,
protective rubber boot, PC software,
adapter cap of the same connector
type as the transmit port, user’s
guide, and carry case.
Calibrated wavelengths
OPM (manual) mode optical power
display range
OLTS (automatic) mode insertion
loss measurement range
850, 980, 1300, 1310, 1480, 1550, 1625 nm
+ 10 to – 70 dBm
+ 10 to – 70 dBm
+ 16 to – 60 dBm
45 dB
45 dB
39 dB
Accuracy at –10 dBm, 25ºC
± 0.25 dB
± 0.25 dB
± 0.25 dB
Ordering Information
When ordering, connector type after the
model number, for example OLTS 5-3 SC.
SC, FC, ST
Filtered InGaAs
General specifications
Display
128 X 64 dot matrix liquid crystal display
Dimensions (H x W x D)
18.5 X 11.1 X 4.6 cm (7.3 X 4.4 X 1.8 in)
Weight
0.55 kg (1.2 lb)
Operating temperature and humidity 0 to +50°C, 90% RH (non-condensing)
-20 to +60°C, 95% RH
Storage temperature and humidity
Power
2 AA (2-cell NiMH or AC optional)
Battery life (typical)
(2) AA - 17 hours; NiMH battery pack - 11 hours
Connector types
Thread-on adapter cap mount
All specifications valid at 25°C unless otherwise specified.
© 2002-2009, AFL Telecommunications, all rights reserved. OLT5-00-2000 Revision F, 2009-08-04
Specifications are subject to change without notice.
32
ORL3B Optical Return Loss Test Set
The ORL3B is a handheld fiber optic test and measurement instrument that offers two
modes of testing. It performs optical return loss measurements (ORL mode) and operates
as an optical power meter (OPM mode).
The ORL3B can store up to 1000 records (40 files) in any combination of its two operating
modes. With the supplied PC software, saved test results can be transferred to a PC for
storage, printing, and analysis. The ORL3B operates from an internal rechargeable
Lithium-Ion battery pack or external AC power adapter.
Specifications
MODEL
ORL3-MM
ORL Specifications
Calibrated wavelengths (nm)
850, 1300
Output power (dBm)
-20
Features
Emitter type
LED
•• Rugged, handheld, designed for field use
•• Provides 850/1300 nm Return Loss and
OPM testing
•• Up to 1000 test records (40 files) storage
and download
•• Free Windows® compatible software to
view, print, and archive test records
•• Li-Ion or AC adapter
•• Cost-effective, easy to use
Safety class
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
ORL dynamic range (dB)
40
Measurement units
dB, dBm, µW
Available connector types
ASC
OPM Specifications
Calibrated wavelengths (nm)
Detector type
Measurement range (dBm)
850, 1300,
InGaAs
+6 to -70
Resolution
0.01 dB
Accuracy @ -10 dBm @ 25°C
± 0.25 dB
Measurement units
dB, dBm, μW
General Specifications
Display type
128 X 64 dot matrix liquid crystal display, with LED backlight
Dimensions, without boot (H x W x D)
19.5 X 10.1 X 5.7 cm (7.67 X 3.97 X 2.25 in)
Weight, without boot
0.907 kg (2 lb)
Operating temperature
0 to +50°C, 90% RH (non-condensing)
Storage temperature
-20 to +60°C, 95% RH
Power
Lithium-Ion or AC Adapter
Battery life (typ.)
32 hours
Li-Ion battery pack charging temp.
-10 to +45°C
Li-Ion battery pack charging time will increase by 25% at a temperature below -5°C.
Do not charge the Li-Ion battery pack at a temperature above +45°C.
Ordering Information
Model
Includes
ORL3-MM
(1) ORL3B, protective rubber boot, PC software, adapter cap of the same connector type as
the transmit port, user’s guide, and carry case.
When ordering, specify transmit port connector type after the model number,
for example ORL3-MM-SC.
© 2002-2009, AFL Telecommunications, all rights reserved. RL3B-00-2000 Revision 1F, 2009-08-04
Specifications are subject to change without notice.
33
OPM4-FTTx PON Power Meter
The Noyes OPM4-FTTx from AFL Telecommunications is designed to measure optical
power in FTTH and other passive optical networks (PONs) that use 1490 nm for
downstream data and 1550 nm for downstream video traffic. In addition, the OPM4-FTTx
provides an integrated Visual Fault Locator (VFL) - 650 nm (red) laser for short-range fault
location and connectivity testing.
Equipped with wavelength filters and a dual photo detector, the OPM4-FTTx can separately
and simultaneously measure 1490 and 1550 nm power at the ONT or other points in
an FTTx PON. A large, dual-wavelength LCD display with backlight shows power at both
wavelengths in units of dBm or µW. The “set reference” feature may be used to measure
the difference between two power (dBm) levels, in units of dB measured at different parts
of the network.
Features
•• BPON, GPON, and EPON compatible
•• Simultaneous power measurement at
1490 and 1550 nm
•• Power shown in units of dBm or µW
•• Comparison of power levels in dB
•• Integrated VFL
•• Auto power shut-off feature
•• Dual-wavelength, sunlight readable LCD
display
•• Compatible with APC or UPC connectors
•• Standard alkaline AA batteries
•• Handheld, rugged, lightweight
•• N.I.S.T traceable
Applications
•• ONT splitter installation testing
•• Fault-locating drop cables and F2 fibers
from FDH to ONT
The power meter and VFL ports accept Noyes thread-on style adapter caps and are
compatible with angled or non-angled connectors. The OPM4-FTTx offers an automatic
power shut-off feature, long battery life from standard AA alkaline batteries, and is fully
N.I.S.T. traceable.
Specifications
Power Meter
Calibrated wavelengths
Signal format
Detector type
Measurement range
Accuracy *
Resolution
Measurement units
VFL Laser
Output power (typical)
Wavelength (nominal)
Safety
General
Power
Battery life (typical)
1490 nm, 1550 nm
CW or downstream BPON, GPON, or EPON
Filtered InGaAs
+10 to -50 dBm @ 1490 nm; +20 to -50 dBm @ 1550 nm
± 0.5 dB (± 0.35 dB typical)
0.01 dB
dB, dBm, μW
0.8 mW
650 nm
Class II, FDA 21 CFR 1040.10 & 1040.11, IEC 60825-1:2007
2 x AA batteries
Power meter:
100 hours
Power meter + VFL: 16 hours
Operating temperature
Storage temperature
Size (H x W x D)
Weight
Power meter (backlight on):
16 hours
Power meter (backlight on) + VFL: 5 hours
-10 to 50°C, 90% RH (non-condensing)
-30 to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.26 kg (0.58 lb)
* At calibration power levels of approximately -5 dBm for 1550 nm and -10 dBm for 1490 nm.
All specifications at 25°C
Ordering Information
Model
OPM4-FTTx
Includes
OPM4-FTTx PON power meter, 2 x AA batteries, protective rubber boot, SC adapter for power
meter port, 2.5 mm universal adapter for VFL port, user’s guide, and carry case.
* Additional adapters are available and must be ordered separately
© 2008, AFL Telecommunications, all rights reserved. OPM4-14-2000 Revision 1C, 12.04.08
Specifications are subject to change without notice.
34
OPM5 Optical Power Meter
The OPM5 from AFL Telecommunications is a full-featured, handheld optical power meter
designed for measuring optical power in Premises, Telco, or Broadband networks and for
performing insertion loss measurements on multimode or single-mode fiber optic links.
The OPM5 features automatic wavelength identification and switching (Wave ID)
when used with Noyes OLS series light sources, multiple test Tone detection for fiber
identification, and stores optical references for each calibrated wavelength and up to 500
records per wavelength of power or insertion loss measurements. Using the supplied
Windows® compatible software and USB connection, test records are transferred to a
PC for analysis, printing, and storage. A large dual-wavelength LCD display with backlight
shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths [nm],
tone signal [Hz], wavelength ID, and estimated remaining battery life.
Features
•• Handheld, rugged, lightweight
•• Multimode or single-mode applications
•• Wave ID (auto identification & switching)
•• Multiple-wavelength testing
•• 270Hz, 330Hz, 1kHz, 2kHz Tone detection
•• Large LCD with backlight
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Automatic power-off function
•• Battery gauge
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• N.I.S.T traceable
The OPM5 optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements. The OPM5 offers a
five-minute auto-off feature and long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The OPM5 is fully N.I.S.T. traceable.
Specifications
Optical
Calibrated wavelengths
OPM5-2D
OPM5-3D
OPM5-4D
850, 1300,
1310, 1490, 1550 nm
850, 1300, 1310, 1550,
1490, 1625 nm
850, 980, 1310, 1490,
1550, 1625 nm
Detector type
Germanium (Ge)
InGaAs
Filtered InGaAs
Measurement range
+6 to -60 dBm
+10 to -75 dBm
+26 to -50 dBm
Tone detect range
+6 to -50 dBm
+10 to -50 dBm
+6 to -45 dBm for 850nm +10 to -45 dBm for 850nm
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+10 to -50 dBm
+6 to -30 dBm
+6 to -45 dBm for 850 nm +10 to -45 dBm for 850 nm +6 to -25 dBm for 850 nm
± 0.25 dB
Accuracy*
Resolution
0.01 dB
Measurement units
General
dB, dBm, μW
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Applications
Weight
0.26 kg (0.58 lb)
•• Premises (Ge), Telco (InGaAs), and
Broadband (+26 dBm) models
•• Passive Optical Networks (PON) testing
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Ordering Information
Model
Includes
All OPM5 models
OPM5 optical power meter, 2 x AA batteries, protective rubber boot, USB cable,
Windows® compatible software and user’s guide, OPM5 user’s guide, and carry case.
© 2004-2009, AFL Telecommunications, all rights reserved. OPM5-30-2000 Revision D, 2009-04-15
Specifications are subject to change without notice.
35
OPM4 Optical Power Meter
The Noyes OPM4 from AFL Telecommunications is a handheld optical power meter
designed for measuring optical power in Premises, Telco, or Broadband networks and for
performing insertion loss measurements on multimode or single-mode fiber optic links.
The OPM4 features automatic wavelength identification and switching (Wave ID)
when used with Noyes OLS series light sources, multiple test Tone detection for fiber
identification, and stores optical references for each calibrated wavelength. A large dualwavelength LCD display with backlight shows measured power [dBm or µW] or insertion
loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and estimated
remaining battery life.
The OPM4 optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements. The OPM4 offers a fiveminute auto-off feature and long battery life from common AA alkaline batteries.
The OPM4 is fully N.I.S.T. traceable.
Features
•• Handheld, rugged, lightweight
•• Multimode or single-mode applications
•• Wave ID (auto identification & switching)
•• Multiple-wavelength testing
•• 270Hz, 330Hz, 1kHz, 2kHz Tone detection
•• Large LCD with backlight
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Automatic power-off function
•• Battery gauge
•• Long battery life with 2 x AA alkaline
•• N.I.S.T traceable
Specifications
Optical
OPM4-1D
OPM4-2D
OPM4-3D
OPM4-4D
Calibrated
wavelengths
660, 780,
850 nm
850, 1300, 1310,
1490, 1550 nm
850, 1300, 1310,
1490, 1550, 1625 nm
850, 980, 1310, 1490,
1550, 1625 nm
Detector type
Silicon (Si)
Germanium (Ge)
InGaAs
Filtered InGaAs
+6 to -60 dBm
+10 to -75 dBm
+26 to -50 dBm
Measurement range +6 to -70 dBm
Tone detect range
+6 to -45 dBm
Wavelength ID
range
—
Accuracy*
+6 to -50 dBm
+10 to -50 dBm
+6 to -45 for 850 nm +10 to -45 for 850 nm
+6 to -30 dBm
+6 to -25 for 850 nm
+6 to -50 dBm
+6 to -45 dBm for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
± 0.25 dB
Resolution
0.01 dB
Measurement units
General
dB, dBm, μW
Power
2 x AA batteries
Battery life
300 hours
Applications
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
•• Premises (Ge), Telco (InGaAs), and
Broadband (+26 dBm) models
•• Passive Optical Networks (PON) testing
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Ordering Information
Model
Includes
All OPM4 models
OPM4 optical power meter, 2 x AA batteries, protective rubber boot, user’s guide, and
carry case.
© 2004-2009, AFL Telecommunications, all rights reserved. OPM4-30-2000 Revision D, 2009-04-16
Specifications are subject to change without notice.
36
OPM1 Optical Power Meter
This portable optical power meter may be used to measure optical power in premises,
telco, or broadband fiber optic networks. When used with an LED or laser light source,
the OPM1 can also measure the attenuation (insertion loss) of multimode or single-mode
cables. With only two controls – ON/OFF and wavelength – the OPM1 is our simplest to
use optical power meter. Optical power in dBm and the calibration wavelength setting are
displayed on an easy-to-read LCD display. The optical input port accepts Noyes thread-on
style connector adapter caps. Adapter caps are required and must be ordered separately.
The OPM1 is fully N.I.S.T. traceable and runs on a standard 9-volt alkaline battery.
Features
• 850, 1300, 1310, 1550 nm
• Premises (Ge) and broadband (InGaAs)
models
• Displays optical power (dBm)
• Our simplest to use optical power meter
• N.I.S.T. traceable
Applications
• The OPM1-2C is calibrated at 850, 1300, 1310, and 1550 nm for testing LAN, Ethernet,
FDDI, Token Ring, and single-mode fiber systems such as Telco, WAN, and CATV.
• The OPM1-3C also operates at 850, 1300, 1310, and 1550 nm but offers greater
temperature stability needed for outside plant 1550 nm testing as with WAN, CATV, and
Telco systems.
Specifications
Optical Specifications
Calibration wavelengths
Detector type
Measurement range
Accuracy (@25° C, -10.0 dBm)
Measurement units
OPM1-2C
OPM1-3C
850, 1300, 1310, 1550 nm
850, 1300, 1310, 1550, 1625 nm
Germanium (Ge)
InGaAs
+6 to -60 dBm
+6 to -70 dBm
±0.25 dB
dBm
General Specifications
Power
Typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Operating temperature
-10 to 50°C
0 to 95% (non-condensing)
Relative humidity
Storage temperature
-30 to 60°C
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
All specifications at 25°C
Ordering Information
Model
Includes
All OPM1 models
Protective rubber boot, 9V battery, manual, and carrying case.
Optical power meters and optical light sources can be packaged together as a kit.
© 2002, AFL Telecommunications, all rights reserved. OPM1-00-2001 Revision N, 6.16.05
Specifications are subject to change without notice.
37
CSM1 Contractor Series Optical Power Meter
The Noyes CSM1 from AFL Telecommunications is a palm-sized, cost-effective optical
power meter designed for measuring optical power in Premises, Telco, or Broadband fiber
optic networks and for performing insertion loss measurements on multimode or singlemode fiber optic links. Weighing only 0.4 lb, this power meter is ideal for field use.
The CSM1 stores optical references for each calibrated wavelength and features multiple
test Tone detection for fiber identification. A large LCD display with backlight shows
measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone
frequency [Hz], and indicates a low battery condition.
The CSM1 optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements. One adapter cap,
2.5mm Universal, is included.
Features
•• Palm-sized, rugged, lightweight
•• Multimode or single-mode applications
•• 270, 330, 1000, 2000 Hz Tone detection
•• Large LCD with backlight
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Automatic power-off function
•• Battery gauge
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
Application
•• Premises (Ge), Telco (InGaAs), and
Broadband (+26 dBm) models
•• Passive Optical Networks (PON) testing
Being powered by two AA alkaline, the CSM1 offers a five-minute auto-off feature and over
300 hours of operation with backlight off.
The CSM1 is fully N.I.S.T. traceable.
Specifications
Optical
CSM1-1
Calibrated
wavelengths
660, 780,
850 nm
850, 1300,
850, 1300, 1310,
1310, 1550 nm 1490, 1550, 1625 nm
Detector type
CSM1-2
CSM1-3
CSM1-4
850, 980,1310, 1490,
1550, 1625 nm
Silicon (Si)
Germanium (Ge)
InGaAs
Filtered InGaAs
Measurement range
+6 to -70 dBm
+6 to -60 dBm
+6 to -70 dBm
+26 to -50 dBm
Tone detect range
+6 to -45 dBm
Accuracy*
+6 to -50 dBm
+6 to -45 dBm for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
± 0.3 dB
Resolution
0.01 dB
Measurement units
General
dB, dBm, μW
Power
2 x AA batteries
Battery life
> 300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
*Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Ordering Information
Model
Includes
All CSM1 models
2.5mm Universal adapter cap, 2 x AA batteries, user’s guide, and carry case.
© 2006-2009, AFL Telecommunications, all rights reserved. CSM1-00-2000 Revision C, 2009-06-23
Specifications are subject to change without notice.
38
OLS7-FTTH & OLS7-3
Triple Wavelength Laser Sources
The OLS7-FTTH and OLS7-3 from AFL Telecommunications are handheld, rugged laser
sources designed for performing insertion loss measurements on single-mode fiber optic
links when used with an optical power meter. When paired with an optical fiber identifier,
both models may be used for fiber identification. The LASER output is stabilized to ensure
accurate test results per current TIA/EIA requirements.
Features
•• Handheld, rugged, lightweight
•• Triple wavelengths from a single port
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
OLS7-FTTH OLS7-FTTH optical light source,
protective rubber boot, 2 x AA
batteries, user’s guide, and carry case.
OLS7-3
OLS7-3 optical light source, protective
rubber boot, 2 x AA batteries, user’s
guide, and carry case.
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single
port and are easy to operate. Each wavelength may be transmitted individually at CW
or with user selectable modulated Tone. Also, each wavelength may be transmitted with
Wave ID. When transmitting with Wave ID, the OLS7 will also support transmitting pairs
of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength wavelength(s) along
with battery charge status and external power presence.
The OLS7-FTTH model is designed specifically for today’s FTTH network architectures
featuring a triple wavelength LASER output from a single port: 1310nm output for testing
in the upstream direction and 1490 or 1550nm, for testing in the downstream direction.
The OLS7-3 model features 1310/1550/1625 nm triple wavelength LASER output that is
used for single-mode applications, such as Telecom or CATV.
The OLS7-FTTH & OLS7-3 output ports are equipped with UCI based removable adapters
to allow the output connectors to be inspected and cleaned. Both models offer long battery
life from common AA alkaline batteries with external AC adapter available as an option.
The OLS7 is fully N.I.S.T. traceable.
Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
Tone output
General
Model OLS7-FTTH
Model OLS7-3
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
Models OLS7-FTTH & OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
SC FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
© 2006-2009, AFL Telecommunications, all rights reserved. OLS7-00-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
OLS4 Integrated Laser and LED Source
The OLS4 from AFL Telecommunication is a handheld, rugged, integrated two-port
LED and LASER light source designed for performing insertion loss measurements on
multimode or single-mode fiber optic links when used with an optical power meter. When
paired with an optical fiber identifier, the OLS4 may be used for fiber identification. The
LED and LASER outputs are stabilized to ensure accurate test results per current TIA/EIA
requirements.
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength(s) along with battery charge
status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Integrated LED and Laser light source
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW, Tone (SM
output)
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Certify multimode and single-mode links
per TIA/EIA standards
•• Fiber identification prior to splicing
Both output ports are equipped with UCI based removable adapters to allow the output
connectors to be inspected and cleaned. The OLS4 coffers long battery life from common
AA alkaline batteries with external AC adapter available as an option.
The OLS4 is fully N.I.S.T. traceable.
Specifications
Optical
Wavelength
Emitter type
Spectral width
Output power
Output Stability
MM Optical Port
SM Optical Port
850 ± 30 nm 1300 -10/+50 nm
1310 ± 20 nm
1550 ± 20 nm
LED
Laser
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
40 nm (typ)
120 nm (typ)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
± 0.05 dB over 1 hour (after 15 min. warm-up)
(after 5 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS4
OLS4 optical light source, protective rubber boot, 2 x AA batteries, mandrels, user’s
guide, and carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. OLS4-11-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
40
OLS2-Dual Laser Light Source
The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed
for performing insertion loss measurements on single-mode fiber optic links when used
with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual
may be used for fiber identification. The LASER output is stabilized to ensure accurate test
results per current TIA/EIA requirements.
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from
common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.
Specifications
Optical
OLS2-Dual (single port)
Wavelength
1310 ±20 nm
Emitter type
1550 ±20 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
General
270 Hz, 330 Hz, 1 kHz, 2 kHz
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS2-Dual
OLS2-Dual optical light source, protective rubber boot, 2 x AA batteries, user’s
guide, and carry case.
© 2004-2009, AFL Telecommunications, all rights reserved. LS2D-20-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
OLS1-Dual LED Light Source
The OLS1-Dual from AFL Telecommunication is a handheld, rugged LED light source
designed for performing insertion loss measurements on multimode fiber optic links when
used with an optical power meter. The LED output is stabilized to ensure accurate test
results per current TIA/EIA requirements.
The OLS1-Dual features 850 nm and 1300 nm LED output from a single output port and is
easy to operate with only a power button and a wavelength select button. Each wavelength
may be transmitted individually at CW or with Wave ID. When transmitting with Wave ID,
the OLS1-Dual supports transmitting pairs of wavelengths in an alternating pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength(s) along with battery
charge status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE) per
TIA/EIA standards
•• The 1300 nm output can also be used to
test short distance (up to 10 km) singlemode fiber links
The output port is equipped with UCI based removable adapters to allow the output connectors to be inspected and cleaned. The OLS1-Dual offers long battery life from common
AA alkaline batteries with external AC adapter available as an option.
The OLS1-Dual is fully N.I.S.T. traceable.
Specifications
Optical
OLS1-Dual (single port)
Wavelength
850 ±30 nm
Emitter type
1300 +50/-10 nm
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
62.5 µm**
Fiber size
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
** May be used to test 50 or 62.5μm fiber with supplied mandrels.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS1-Dual
OLS1-Dual optical light source, protective rubber boot, 2 x AA batteries,
mandrels, user’s guide, and carry case.
© 2004-2009, AFL Telecommunications, all rights reserved. LS1D-30-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
42
OLS1 LED Light Source
The OLS1 LED light source is a cost-effective, rugged, handheld instrument designed for
performing insertion loss measurements on fiber optic links when used with an optical
power meter. The LED output is stabilized to ensure accurate test results per current
TIA/EIA requirements.
The OLS1 is easy to operate with only a [Wavelength/ Power] switch, which selects optical
wavelengths or disables unit ( position). [Active Output], [Battery], and [External Power]
indicators identify the currently enabled output port, battery charge status, and external
power presence. Weighing only 0.65 lb, the OLS1 is compact and convenient for field
use. The OLS1 operates over 60 hours from a typical 9V alkaline battery. An AC adapter is
optional for extended use.
The OLS1 light source is fully N.I.S.T. traceable.
Applications
Features
• Rugged, handheld, lightweight
• 850 and 1300 nm LED (multimode) light
sources (660 nm available)
• Certify 50 or 62.5µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE) per
TIA/EIA standards
• Free 50µm and 62.5µm mandrels
• Long battery life
• Cost-effective, easy to use
• N.I.S.T. Traceable
• Operating at 850 nm, the OLS1-1C can be used for testing Ethernet, Gigabit Ethernet,
Token Ring, and other multimode ­LAN systems.
• Operating at 660 nm, the OLS1-1C can test 1000µ ­fiber and trace fibers with the visible
660 nm output.
• The OLS1-2C operates at 850 and 1300 nm for use on Ethernet, Token Ring, and FDDI.
The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links.
Specifications
Optical Specifications
Output wavelength
Model
Includes
All OLS1
models
Protective rubber boot, 9V battery,
50 and 62.5µm mandrels, manual,
and carrying case.
Optical light sources and optical power
meters can be packaged together as a kit.
OLS1-2C
2
2
660 nm- red
Spectral width (typ) (FWHM)
Output power
Fiber size
Ordering Information
OLS1-1C
Output ports
Output connector
Emitter type
850 + 35/-40 nm 850 + 35/-40 nm 1300 +50/-10 nm
30 nm
40 nm
40 nm
120 nm
-10 dBm*
>-20 dBm
>-20 dBm
>-20 dBm
1000 µm, 62.5 µm**
62.5 µm**
ST
ST
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
General Specifications
Power
Typical 60 hours with 9V battery, optional AC adapter
Operating temperature
-10 to 50°C
Storage temperature
-30 to 60°C
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* -10 dBm output is into 1000 micron fiber.
* * May be used to test 50 or 62.5μm fiber with supplied mandrels.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. OLS1-00-2001 Revision P, 2009-06-16
Specifications are subject to change without notice.
43
CSS1-SM Contractor Series Dual Laser
Light Source
The Noyes CSS1-SM from AFL Telecommunications is a palm-sized, cost-effective dual
LASER source designed for performing insertion loss measurements on single-mode
fiber optic links when used with an optical power meter. When paired with an optical fiber
identifier, the CSS1-SM may be used for fiber identification. The LASER output is stabilized
to ensure accurate test results per current TIA/EIA requirements. Weighing only 0.4 lb, this
light source is ideal for field use.
The CSS1-SM features 1310 nm and 1550 nm LASER output from a single output port
and is easy to operate. Each wavelength may be transmitted individually at CW or with
user selectable modulated Tone. The output port is equipped with UCI based removable
adapters to allow the output connectors to be inspected and cleaned. A large LCD display
with backlight shows emitted wavelengths [nm], tone frequency [Hz], and indicates a low
battery condition. The CSS1-SM offers long battery life from common AA alkaline batteries.
Features
•• Palm-sized, rugged, lightweight
•• Dual wavelengths from a single port
•• CW and modulated Tone
•• 270, 330, 1000, 2000 Hz Tone
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
The CSS1-SM is fully N.I.S.T. traceable.
Specifications
Optical
CSS1-SM (single port)
Output wavelength
1310 nm ±20 nm, 1550 nm ±20 nm
Spectral width (max)
5 nm
Output power
0.0 dBm into 9/125 fiber
Emitter type
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Output stability
± 0.05 dB typical over 1 hour (after 30 sec. )
± 0.15 dB over 8 hours (after 30 sec. typically)
Tone output
270, 330, 1000, 2000 Hz
General
Output connector
SC, FC, ST, LC
Power
2 x AA batteries
Battery life
75 hours typical
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
All specifications at 25°C.
Ordering Information
Model
Includes
CSS1-SM
2 x AA batteries, user’s guide, and carry case.
© 2006-2009, AFL Telecommunications, all rights reserved. CSS1-00-2000 Revision C, 2009-06-23
Specifications are subject to change without notice.
CSS1-MM
Contractor Series Dual LED Light Source
The Noyes CSS1-MM from AFL Telecommunications is a palm-sized, cost-effective dual
LED light source designed for performing insertion loss measurements on multimode
fiber optic links when used with an optical power meter. When paired with an optical fiber
identifier, the CSS1-MM may be used for fiber identification. The LED output is stabilized
to ensure accurate test results per current TIA/EIA requirements. Weighing only 0.4 lb, this
light source is ideal for field use.
Features
•• Palm-sized, rugged, lightweight
•• Dual wavelengths from a single port
•• CW and modulated Tone
•• 270, 330, 1000, 2000 Hz Tone
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE), per
TIA/EIA standards
•• Fiber identification prior to splicing
The CSS1-MM features 850 nm and 1300 nm LED output from a single output port and
is easy to operate. Each wavelength may be transmitted individually at CW or with user
selectable modulated Tone. The optical output port is equipped with a fixed SC connector.
A large LCD display with backlight shows emitted wavelengths [nm], tone frequency [Hz],
and indicates a low battery condition. The CSS1-MM offers a five-minute auto-off feature
and long battery life from common AA alkaline batteries.
The CSS1-MM is fully N.I.S.T. traceable.
Specifications
Optical
CSS1-MM (single port)
Output wavelength
850 nm ±20 nm
1300 nm +40/-60 nm
Spectral width (max)
35 nm
170 nm
Output power
-20.0 dBm into 62.5/125 fiber
Emitter type
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Output stability
± 0.1 dB over 1 hour (after 30 sec typically)
± 0.15 dB over 8 hours (after 30 sec typically)
Tone output
270, 330, 1000, 2000 Hz
General
Output connector
SC
Power
2 x AA batteries
Battery life
30 hours typical
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
All specifications at 25°C
Ordering Information
Model
Includes
CSS1-MM
2 x AA batteries, user’s guide, and carry case.
© 2006-2009, AFL Telecommunications, all rights reserved. CSS1-01-2000 Revision C, 2009-06-23
Specifications are subject to change without notice.
SMLP5-5 Single-mode/Multimode Test
Kit with Wave ID, Set Reference, and
Data Storage
The SMLP5-5 test kit combines the OPM5-2D optical power meter and OLS4 integrated
LED and LASER light source and is ideally suited for testing fiber optic networks with
hybrid (single-mode and multimode) cables.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM5-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength(s) along with battery charge
status and external power presence. Both output ports are equipped with UCI based
removable adapters to allow the output connectors to be inspected and cleaned.
The OPM5-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS4, multiple test Tone detection for fiber identification, and stores optical
references for each calibrated wavelength and up to 500 records per wavelength of power
or insertion loss measurements. Using the supplied Windows® compatible software and
USB connection, test records are transferred to a PC for analysis, printing, and storage.
A large dual-wavelength LCD display with backlight shows measured power [dBm or µW]
or insertion loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and
estimated remaining battery life. The OPM5-2D optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements.
The OPM5-2D or OLS4 offer long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The SMLP5-5 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode and single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SMLP5-5
OLS4 optical light source, OPM5-2D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, 50 and 62.5µm
mandrels, SMLP5-5 test kit user's guide, and carry case
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-55-2001 Revision D, 2009-06-16
Specifications are subject to change without notice.
46
SMLP5-5 Single-mode/Multimode Test Kit with Wave ID, Set
Reference, and Data Storage
OLS4 Light Source specifications
Optical
Wavelength
Emitter type
Spectral width
Output power
Output Stability
MM Optical Port
SM Optical Port
850 ± 30 nm
1300 -10/+50 nm
1310 ± 20 nm
1550 ± 20 nm
LED
Laser
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
40 nm (typ)
120 nm (typ)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
± 0.05 dB over 1 hour (after 15 min. warm-up)
(after 5 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
General
Power
Battery life
Available adapters
Operating temperature
Storage temperature
Size (H x W x D)
Weight
2 x AA batteries, optional AC adapter
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
SC FC, ST, LC
-10 to 50°C, 90% RH (non-condensing)
-30 to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
All specifications at 25°C.
OPM5-2D specifications
Optical
Calibrated wavelengths
OPM5-2D
850, 1300, 1310, 1490, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Accuracy*
Resolution
Measurement units
General
Power
Battery life
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries, optional AC adapter
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-55-2001 Revision D, 2009-06-16
Specifications are subject to change without notice.
47
SMLP4-4 Single-mode/Multimode Test
Kit with Wave ID and Set Reference
The SMLP4-4 test kit combines the OPM4-2D optical power meter and OLS4 integrated
LED and LASER light source and is ideally suited for testing fiber optic networks with
hybrid (single-mode and multimode) cables.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM4-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated with
each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status
and external power presence. Both output ports are equipped with UCI based removable
adapters to allow the output connectors to be inspected and cleaned.
The OPM4-2D features automatic wavelength identification and switching (Wave ID)
when used with the OLS4, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-2D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-2D and OLS4 offer long battery life from common AA alkaline batteries.
The SMLP4-4 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode and single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SMLP4-4
OLS4 optical light source, OPM4-2D optical power meter, AA batteries, protective rubber boots,
adapter cap, 50 and 62.5µm mandrels, SMLP4-4 test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-44-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
48
SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and
Set Reference
OLS4 Light Source specifications
Optical
Wavelength
Emitter type
Spectral width
Output power
Output Stability
MM Optical Port
SM Optical Port
850 ± 30 nm
1300 -10/+50 nm
1310 ± 20 nm
1550 ± 20 nm
LED
Laser
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
40 nm (typ)
120 nm (typ)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
± 0.05 dB over 1 hour (after 15 min. warm-up)
(after 5 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
General
Power
Battery life
Available adapters
Operating temperature
Storage temperature
Size (H x W x D)
Weight
2 x AA batteries, optional AC adapter
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
SC FC, ST, LC
-10 to 50°C, 90% RH (non-condensing)
-30 to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
All specifications at 25°C.
OPM4-2D specifications
Optical
Calibrated wavelengths
OPM4-2D
850, 1300,1310, 1490, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
Wavelength ID range
Accuracy*
Resolution
Measurement units
General
Power
Battery life
+6 to -50 dBm
+6 to -45 for 850 nm
+6 to -50 dBm
+6 to -45 dBm for 850 nm
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-44-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
49
SLP5 Triple Wave Test Kits with Wave ID,
Set Reference, and Data Storage
The SLP5 triple wavelength single-mode test kits are available in two models, SLP5-FTTH
and SLP5-7. The SLP5-FTTH and SLP5-7 model combine the OPM5-4D optical power
meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm)
LASER source respectively.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM5-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single port
and are easy to operate. Each wavelength may be transmitted individually at CW or with
user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID.
When transmitting with Wave ID, the OLS7 will also support transmitting pairs of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength wavelength(s) along with battery charge status and external power presence. The OLS7-FTTH & OLS7-3 output ports
are equipped with UCI based removable adapters to allow the output connectors to be
inspected and cleaned.
The OPM5-4D features automatic wavelength identification and switching (Wave ID)
when used with the OLS7, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM5-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM5-4D and OLS7 offer long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The SLP5-FTTH and SLP5-7 test kits are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP5 -7
OLS7-3 optical light source, OPM5-4D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, SLP5-7 test kit user's
guide, and carry case.
SLP5-FTTH OLS7-FTTH optical light source, OPM5-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, USB cable, Windows® compatible software and user’s guide, SLP5-FTTH test
kit user’s guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006-2009, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision B, 2009-06-16
Specifications are subject to change without notice.
50
SLP5 Triple Wave Test Kits with Wave ID, Set Reference, and
Data Storage
OLS7 Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
Tone output
General
Model OLS7-FTTH
Model OLS7-3
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
Models OLS7-FTTH & OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
SC, FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
OPM5-4D specifications
Optical
Calibrated wavelengths
OPM5-4D
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
Resolution
Measurement units
General
Power
Battery life
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries, optional AC adapter
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2009, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision B, 2009-06-16
Specifications are subject to change without notice.
51
SLP5-6D Single-mode Test Kit with Wave
ID, Set Reference, and Data Storage
The SLP5-6D test kit combines the OPM5-4D optical power meter and OLS2-Dual LASER
light source and is ideally suited for testing single-mode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Large LCD with backlight (OPM5-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned.
The OPM5-4D features automatic wavelength identification and switching (Wave ID) when
used with the OLS2-Dual, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength and up to 500 records per wavelength of
power or insertion loss measurements. Using the supplied Windows® compatible software
and USB connection, test records are transferred to a PC for analysis, printing, and
storage. A large dual-wavelength LCD display with backlight shows measured power [dBm
or µW] or insertion loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID,
and estimated remaining battery life. The OPM5-4D optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements.
The OPM5-4D and OLS2-Dual offer long battery life from common AA alkaline batteries
with external AC adapter available as an option.
The SLP5-6D test kit is fully N.I.S.T. traceable.
Applications
•• Certify single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SLP5 -6D
OLS2-Dual optical light source, OPM5-4D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, SLP5-6D test kit user's
guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SLP5-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
52
SLP5-6D Single-mode Test Kit with Wave ID, Set Reference,
and Data Storage
OLS2-Dual specifications
Optical
OLS2-Dual (single port)
Wavelength
Emitter type
1310 ±20 nm
1550 ±20 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
General
270 Hz, 330 Hz, 1 kHz, 2 kHz
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
OPM5-4D specifications
Optical
Calibrated wavelengths
OPM5-4D
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
Resolution
Measurement units
General
Power
Battery life
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries, optional AC adapter
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SLP5-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
53
SLP4 Triple Wave Test Kits with Wave ID
and Set Reference
The SLP4 triple wavelength single-mode test kits are available in two models, SLP4-FTTH
and SLP4-7. The SLP4-FTTH and SLP4-7 model combine the OPM4-4D optical power
meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm)
LASER source respectively.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM4-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify single-mode links per TIA/EIA
standards
•• Fiber identification prior to splicing
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single port
and are easy to operate. Each wavelength may be transmitted individually at CW or with
user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID.
When transmitting with Wave ID, the OLS7 will also support transmitting pairs of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength wavelength(s) along with battery charge status and external power presence. The OLS7-FTTH & OLS7-3 output ports
are equipped with UCI based removable adapters to allow the output connectors to be
inspected and cleaned.
The OPM4-4D features automatic wavelength identification and switching (Wave ID)
when used with the OLS7, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-4D and OLS7 offer long battery life from common AA alkaline batteries.
The SLP4-7 and SLP4-FTTH kits are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP4-7
OLS7-3 optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-7 test kit user's guide, and carry case.
SLP4-FTTH
OLS7-FTTH optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-FTTH test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006-2009, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision B, 2009-06-16
Specifications are subject to change without notice.
54
SLP4 Triple Wave Test Kits with Wave ID and Set Reference
OLS7 Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
Tone output
General
Model OLS7-FTTH
Model OLS7-3
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
Models OLS7-FTTH & OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
SC FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
OPM4-4D specifications
Optical
Calibrated wavelengths
OPM4-4D
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
Tone detect range
+26 to -50 dBm
Wavelength ID range
+6 to -30 dBm
+6 to -25 for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
General
Power
Battery life
dB, dBm, μW
2 x AA batteries
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
Weight
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2009, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision B, 2009-06-16
Specifications are subject to change without notice.
55
SLP4-6D Single-mode Test Kit with Wave
ID and Set Reference
The SLP4-6D test kit combines the OPM4-4D optical power meter and OLS2-Dual LASER
light source and is ideally suited for testing single-mode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Large LCD with backlight (OPM4-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned.
The OPM4-4D features automatic wavelength identification and switching (Wave ID) when
used with the OLS2-Dual, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-4D and OLS2-Dual offer long battery life from common AA alkaline batteries.
The SLP4-6D test kit is fully N.I.S.T. traceable.
Applications
•• Certify single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SLP4-6D
OLS2-Dual optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-6D test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
56
SLP4-6D Single-mode Test Kit with Wave ID and Set Reference
OLS2-Dual specifications
Optical
OLS2-Dual (single port)
Wavelength
Emitter type
1310 ±20 nm
1550 ±20 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
General
270 Hz, 330 Hz, 1 kHz, 2 kHz
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
OPM4-4D specifications
Optical
Calibrated wavelengths
OPM4-4D
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
Wavelength ID range
Accuracy*
Resolution
Measurement units
General
Power
Battery life
+6 to -30 dBm
+6 to -25 for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
57
MLP5-2 Multimode Test Kit with Wave
ID, Set Reference, and Data Storage
The MLP5-2 test kit combines the OPM5-2D optical power meter and OLS1-Dual LED light
source and is ideally suited for testing multimode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW
•• Large LCD with backlight (OPM5-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS1-Dual features 850 and 1300 nm LED output from a single output port and is
easy to operate with only a power button and a wavelength select button. Each wavelength
may be transmitted individually at CW or with Wave ID. When transmitting with Wave
ID, the OLS1-Dual supports transmitting pairs of wavelengths in an alternating pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength(s) along with battery
charge status and external power presence. The OLS1-Dual output port is equipped with
UCI based removable adapters to allow the output connectors to be inspected and cleaned.
The OPM5-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS1-Dual and stores optical references for each calibrated wavelength
and up to 500 records per wavelength of power or insertion loss measurements. Using
the supplied Windows® compatible software and USB connection, test records are
transferred to a PC for analysis, printing, and storage. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM5-2D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OLS1-Dual and OPM5-2D offer long battery life from common AA alkaline batteries
with external AC adapter available as an option.
The MLP5-2 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode fiber links per TIA/EIA standards
•• The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links
Ordering Information
Model
Includes
MLP5-2
OLS1-Dual optical light source, OPM5-2D optical power meter, AA batteries, protective rubber
boots, adapter cap, USB cable, Windows® compatible software and user's guide, 50 and 62.5µm
mandrels, MLP5-2 test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. MLP5-30-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
58
MLP5-2 Multimode Test Kit with Wave ID, Set Reference, and
Data Storage
OLS1-Dual specifications
Optical
OLS1-Dual (single port)
Wavelength
850 ±30 nm
Emitter type
1300 +50/-10 nm
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
62.5 µm**
Fiber size
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used
instead of a 62.5 µm mandrel-wrapped jumper.
** May be used to test 50 or 62.5 μm fiber with supplied mandrels.
All specifications at 25°C.
OPM5-2D specifications
Optical
OPM5-2D
Calibrated wavelengths
850, 1300, 1310, 1490, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
General
dB, dBm, μW
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. MLP5-30-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
59
MLP4-2 Multimode Test Kit with Wave ID
and Set Reference
The MLP4-2 test kit combines the OPM4-2D optical power meter and OLS1-Dual LED light
source and is ideally suited for testing multimode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW
•• Large LCD with backlight (OPM4-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS1-Dual features 850 and 1300 nm LED output from a single output port and is
easy to operate with only a power button and a wavelength select button. Each wavelength
may be transmitted individually at CW or with Wave ID. When transmitting with Wave
ID, the OLS1-Dual supports transmitting pairs of wavelengths in an alternating pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength(s) along with battery
charge status and external power presence. The OLS1-Dual output port is equipped with
UCI based removable adapters to allow the output connectors to be inspected and cleaned.
The OPM4-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS1-Dual and stores optical references for each calibrated wavelength. A
large dual-wavelength LCD display with backlight shows measured power [dBm or µW] or
insertion loss [dB], calibrated wavelengths [nm], wavelength ID, and estimated remaining
battery life. The OPM4-2D optical input port accepts a variety of Noyes thread-on style
adapter caps (ordered separately) to meet a wide range of testing requirements.
The OPM4-2D and OLS1-Dual offer long battery life from common AA alkaline batteries.
The MLP4-2 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode fiber links per TIA/EIA standards
•• The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links
Ordering Information
Model
Includes
MLP4-2
OLS1-Dual optical light source, OPM4-2D optical power meter, AA batteries, protective rubber
boots, adapter cap, 50 and 62.5µm mandrels, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. MLP4-30-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
60
MLP4-2 Multimode Test Kit with Wave ID and Set Reference
OLS1-Dual specifications
Optical
OLS1-Dual (single port)
Wavelength
Emitter type
850 ±30 nm
1300 +50/-10 nm
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
Fiber size
62.5 µm**
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
** May be used to test 50 or 62.5μm fiber with supplied mandrels.
All specifications at 25°C.
OPM4-2D specifications
Optical
Calibrated wavelengths
OPM4-2D
850, 1300,1310, 1490, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
Wavelength ID range
Accuracy*
Resolution
Measurement units
General
Power
Battery life
+6 to -50 dBm
+6 to -45 for 850 nm
+6 to -50 dBm
+6 to -45 dBm for 850 nm
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. MLP4-30-2000 Revision C, 2009-06-16
Specifications are subject to change without notice.
61
MLP1 Fiber Optic Loss Test Kits
The MLP1 test kits are inexpensive solutions for testing multimode and single-mode
systems. By joining the OPM 1 optical power meter and the OLS1 optical light source, the
MLP1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit
are available for testing Premises networks, LAN, and Gigabit Ethernet. The MLP1-1S test
kit includes the OPM1-2C power meter and OLS1-1C light source. The MLP1-2 test kit
combines the OPM1-2C optical power meter and OLS1-2C optical light source
Features
• Multimode and Single-mode testing
• Loss measurements at 850 and 1300nm
• Includes 50 and 62.5 µm mandrels
• Field portable, battery operated
• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300nm application,
including Gigabit Ethernet (GBE)
• N.I.S.T. traceable
Ordering Information
Specifications
Model
Optical Light Source
Output ports
Output wavelength
MLP1-2
OLS1-2C
2
2
660 nm - red 850 + 35/-40nm 850 + 35/-40 nm 1300 + 50/-10 nm
Spectral width (typ) (FWHM)
Output power
Stability (@25°C, 5 min. warm-up)
Fiber size
Emitter type
30 nm
40 nm
40 nm
120 nm
-10 dBm*
>-20 dBm
-20 dBm
>-20 dBm
0.1 dB over 8 hours
0.1 dB over 8 hours
1000 µm, 62.5 µm**
62.5 µm**
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Power
Typical 60 hours with 9V battery, optional AC adapter
Connector
Model
Includes
Size (H x W x D)
All MLP1
models
Optical light source, optical power
meter, protective rubber boots,
adapter cap, 50 and 62.5µm mandrels, user’s guide, and carrying case.
Weight
Test jumpers and connector adapters
are required for operation (purchased
separately). Test jumpers with a variety
of connector styles and fiber types are
available. Adapter caps for most common
connectors may be purchased from AFL
Telecommunications.
MLP1-1S
OLS1-1C
ST
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.65 lb (.29 kg)
* -10 dBm output is into 1000 micron fiber.
* * May be used to test 50 or 62.5μm fiber with supplied mandrels.
Optical Power Meter
OPM1-2C
Calibration wavelength
850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Dynamic range
+6 to -60 dBm
Accuracy (@ 25°C & -10.0 dBm)
±0.25 dB
Measurement units
dBm
Power
Typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.58 lb (0.26 kg)
General Kit Specifications
Dynamic range:
Multimode ( 62.5/125 µm)
Single-mode ( 9/125 µm)
Weight
MLP1-1S
MLP1-2
40 dB @ 850 nm
40 dB @ 850 & 1300 nm
20 dB @ 1300 nm
2. 9 lbs (1.3 kg)
Dimensions (H x W x D)
23.4 x 34 x 10.7 cm (9.2 x 13.4 x 4.2 in)
Operating temperature
-10 to 50°C
Storage temperature
-30 to 60°C
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. MLP1-01-2000 Revision P, 2009-06-16
Specifications are subject to change without notice.
62
CKSM-2 Contractor Series Multimode &
Single-mode Test Kit with Set Reference
Combining the CSM1-2 optical power meter, CSS1-MM Dual LED light source, and
CSS1-SM Dual LASER source, the CKSM-2 is a cost-effective test kit designed for
performing insertion loss measurements on multimode as well as single-mode fiber optic
links. Weighing only 0.4 lb each, units are compact and convenient for field use.
Features
•• Palm-sized, rugged, lightweight
•• CW and modulated Tone
•• 270, 330, 1000, and 2000 Hz Tone
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Certify multimode and single-mode fiber
links per TIA/EIA standards
•• Fiber identification prior to splicing
The CSS1-MM and CSS1-SM sources feature Dual output, 850/1300 nm LED or
1310/1550 nm LASER respectively, from a single output port. Both CSS1 models offer
2 modes of operation, continuous wave (CW) and user selectable modulated Tone. The
CSS1-MM LED and CSS1-SM LASER output ports are stabilized to ensure accurate
test results per current TIA/EIA requirements.A large LCD display with backlight shows
emitted wavelengths [nm], tone frequency [Hz], and indicates a low battery condition. The
CSS1-MM model output port is equipped with a fixed SC connector while the CSS1-SM
output port is equipped with Universal Connector Interface (UCI) base and SC adapter.
The CSM1-2 optical power meter operates at 850/1300/1310/1550 nm and features
multiple test Tone detection for fiber identification. The CSM1-2 stores optical references
for each calibrated wavelength. A large LCD display with backlight shows measured power
[dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone frequency [Hz],
and indicates a low battery condition. The CSM1 optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements. One adapter cap, 2.5mm Universal, is included.
The CSS1-MM, CSS1-SM, and CSM1-2 are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
CKSM-2 CSS1-MM Dual LED source, CSS1-SM Dual Laser souce, CSM1-2 optical power meter, AA batteries,
2.5mm universal adapter cap, UCI-SC connector, 50 and 62.5µm mandrels, user's guide, and carry
case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications. The CKSM kits may
be packed with one of cleaning kit options (purchased separately) as follows:
Model
Description Includes
8500-20-0900 Wet Cleaning Kit 8500-10-0016, Cletop -SB
CCTS-25-0900, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adaptors).Blue (40 sticks per tube). Qty = 2 tubes
FCC2-00-0900, Optical Quality Cleaning Fluid for fiber connector end faces.
8500-20-0901 Dry Cleaning Kit 8500-10-0016, Cletop -SB
8500-10-0024 ACT-01 2.5mm adapter cleaning tips – Qty = 200
continued on the next page
© 2006-2009, AFL Telecommunications, all rights reserved. CKSM-20-2000 Revision C, 2009-05-23
Specifications are subject to change without notice.
63
CKSM-2 Contractor Series Multimode & Single-mode Test Kit with Set Reference
CSS1-SM Specifications
CSS1-MM Specifications
Optical
CSS1-SM (single port)
Optical
Output wavelength
1310 nm ±20 nm, 1550 nm ±20 nm
Output wavelength
850 nm ±20 nm
1300 nm +40/-60 nm
Spectral width (max)
5 nm
Spectral width (max)
35 nm
170 nm
Output power
0.0 dBm into 9/125 fiber
CSS1-MM (single port)
Output power
Emitter type
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1:
2007-03
Emitter type
Output stability
± 0.05 dB typical over 1 hour (after 30 sec. )
± 0.15 dB over 8 hours (after 30 sec. typically)
Output stability
Tone output
270, 330, 1000, 2000 Hz
Tone output
General
-20.0 dBm into 62.5/125 fiber
LED, Class I FDA 21 CFR 1040.10 and 1040.11,
IEC 60825-1: 2007-03
± 0.1 dB over 1 hour (after 30 sec typically)
± 0.15 dB over 8 hours (after 30 sec typically)
270, 330, 1000, 2000 Hz
General
Output connector
SC, FC, ST, LC
Output connector
Power
2 x AA batteries
Power
Battery life
75 hours typical
Battery life
SC
2 x AA batteries
30 hours typical
Operating temperature -10 to 50°C, 90% RH (non-condensing)
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
Weight
All specifications at 25°C.
0.18 kg (0.4 lb)
All specifications at 25°C
CSM1-2 Specifications
Optical
CSM1-2
Calibrated wavelengths 850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850 nm
Accuracy*
± 0.3 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
> 300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
*Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2009, AFL Telecommunications, all rights reserved. CKSM-20-2000 Revision C, 2009-05-23
Specifications are subject to change without notice.
64
CKM-2 Contractor Series Multimode
Test Kit with Set Reference
Combining the CSM1-2 optical power meter and CSS1-MM Dual LED light source, the
CMK-2 is a cost-effective test kit designed for performing insertion loss measurements
on multimode fiber optic links. Weighing only 0.4 lb each, both units are compact and
convenient for field use.
Features
•• Palm-sized, rugged, lightweight
•• CW and modulated Tone
•• 270, 330, 1000, 2000 Hz Tone
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The CSS1-MM Dual light source features 850 nm and 1300 nm LED output from a single
output port and offers 2 modes of operation, continuous wave (CW) and user selectable
modulated Tone. The LED output is stabilized to ensure accurate test results per current
TIA/EIA requirements and equipped with a fixed SC connector. A large LCD display with
backlight shows emitted wavelengths [nm], tone frequency [Hz], and indicates a low
battery condition.
The CSM1-2 optical power meter operates at 850/ 1300/ 1310/ 1550 nm and features
multiple test Tone detection for fiber identification. The CSM1-2 stores optical references
for each calibrated wavelength. A large LCD display with backlight shows measured power
[dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone frequency [Hz],
and indicates a low battery condition. The CSM1 optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements. One adapter cap, 2.5 mm Universal, is included.
Both units offer a five-minute auto-off feature and long battery life from common AA
alkaline batteries.
The CSM1-2 and CSS1-MM are fully N.I.S.T. traceable.
Ordering Information
Applications
Model
Includes
•• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE), per
TIA/EIA standards
•• Fiber identification prior to splicing
CKM-2
CSS1-MM dual optical light source, CSM1-2 optical power meter, AA batteries, 2.5 mm Universaladapter cap, 50 and 62.5 µm mandrels, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
The CKM-2 kits may be packed with one of cleaning kit options (purchased separately) as
follows:
Model
Description Includes
8500-20-0900 Wet Cleaning Kit 8500-10-0016, Cletop -SB
CCTS-25-0900, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adaptors).Blue (40 sticks per tube). Qty = 2 tubes
FCC2-00-0900, Optical Quality Cleaning Fluid for fiber connector end faces.
8500-20-0901 Dry Cleaning Kit 8500-10-0016, Cletop -SB
8500-10-0024 ACT-01 2.5mm adapter cleaning tips – Qty = 200
continued on the next page
© 2006-2009, AFL Telecommunications, all rights reserved. CKM2-00-2000 Revision C, 2009-06-23
Specifications are subject to change without notice.
65
CKM-2 Contractor Series Multimode Test Kit with Set Reference
CSS1-MM Specifications
Optical
CSS1-MM (single port)
Output wavelength
850 nm ±20 nm
1300 nm +40/-60 nm
Spectral width (max)
35 nm
170 nm
Output power
-20.0 dBm into 62.5/125 fiber
Emitter type
LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Output stability
± 0.1 dB over 1 hour (after 30 sec typically)
± 0.15 dB over 8 hours (after 30 sec typically)
Tone output
270, 330, 1000, 2000 Hz
General
Output connector
SC
Power
2 x AA batteries
Battery life
30 hours typical
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
All specifications at 25°C
CSM1-2 Specifications
Optical
CSM1-2
Calibrated wavelengths
850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850 nm
Accuracy*
± 0.3 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
> 300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
*Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2009, AFL Telecommunications, all rights reserved. CKM2-00-2000 Revision C, 2009-06-23
Specifications are subject to change without notice.
66
HiLite and VFI2 Visual Fault Identifiers
The HiLite and VFI2 are compact and powerful visible red laser sources designed to
troubleshoot faults on fiber optic cables. Light generated by these units will escape from
sharp bends and breaks in jacketed or bare fibers, as well as poorly mated connectors.
They enable technicians to quickly identify faults in fiber optic jumper cables, distribution
frames, patch panels, and splice trays.
VFI 2
The HiLite and VFI2 are an excellent complement to an OTDR because they can locate
faults inside the OTDR’s dead-zone. Other applications include end-to-end continuity
checks, identifying connectors in patch panels and fibers during splicing operations. The
universal connector interface provides fast operation with many connector styles without
changing an adapter.
Features
•• Visible red laser source, 650 nm
•• High power, 1 mW
•• Compact size
•• Universal connector interface for quick connection
•• 2.5 mm Universal adapter included
Specifications
HiLite
Optical
VFI2
Emitter type
HiLite
Laser, Class II FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1:2007-03
Wavelength
650 nm ± 10 nm
Output power
1 mW (into single-mode fiber)
Modulation
General
2 Hz or CW selected
Adapter
2.5 mm Universal
Power
2 AA alkaline batteries (60 hours typical)
Operating temperature
1 AAA alkaline battery (16 hours typical)
-10 to 50°C, 85% humidity non condensing
Storage temperature
Size (H x W x D)
2 Hz
-30 to 60°C, 95% humidity non condensing
14.0 x 6.2 x 3.2 cm (5.5 x 2.4 x 1.3 in)
7.0 x 3.6 x 1.5 cm (2.8 x 1.4 x 0.6 in)
< 200 g (7.06 oz)
50 g (1.75 oz)
Weight
Ordering Information
Model
Includes
VFI2
VFI2 unit, instruction card, and carrying case
HiLite
HiLite unit, instruction card, and carrying case
Available Adapters
Model
Description
2900-50-0007MR
2.5 mm Universal adapter 1 with captivated sleeve
2900-50-0010MR
1.25 mm Universal adapter 2 with captivated sleeve
1 2.5 mm Universal adapter accepts SC, FC, ST, E2000, etc. ferrules.
2 1.25 mm Universal adapter accepts LC, MU, etc. ferrules.
© 2002-2009, AFL Telecommunications, all rights reserved. VFI3-00-2000 Revision L, 2009-11-02
Specifications are subject to change without notice.
MT Tracer
12-Fiber Visible Laser Source & Display
The MT Tracer is a compact multi-fiber visual fault identifier (red laser source) supporting 8
or 12 fiber MTP® connections. The user simply connects the 12-fiber cable directly to the
unit. Fibers can be tested individually or all at once. By progressing sequentially through
the fibers, cables can be quickly checked for polarity by verifying the proper order at the
output.
The MT Tracer Display is a passive optical device designed to receive the light from the
MT Tracer Source and provide an eye-safe method of viewing the red light. Identification
is accomplished by expanding the output of the MT ferrule to a large easy to read panel
- large enough to be read from several feet away.
Features
• Viewing safe for eyes
• CW or 2Hz output
• Direct connect - No fan-outs necessary
• Test 8 and 12 fiber MTP® assemblies
• Test polarity, continuity, and fiber mismatch
Specifications
MT Tracer Source Specifications
Optical Wavelength
650 ± 10nm
Output Power Level
min 0.5mW & typ. 1.0mW (at each SM 9/125 fiber at the end of MTP patchcord)
Optical Connector
MTP® male SM, angled
No. of output fibers
12
Power
2 x AA alkaline batteries, optional AC adapter
Battery life (alkaline)
40 hrs.
Low Battery
Indicated by 2 Hz LED blinking
Operation Temperature
0 to 40°C, RH 85% non-condensing
Storage Temperature
-30 to 50°C, RH 95% non-condensing
Dimensions
9.9 x 3.8 x 14.3cm (3.9 x 1.5 x 5.6in)
Weight
MT Tracer Display Specifications
Input Connector
0.29kg (0.63lb)
MTP® angled male 62.5µ fiber
No. of input connectors
1 (12-fiber MTP)
Power Consumption
NA
Operation Temperature
0 to 40°C. RH 85% non-condensing
Storage Temperature
-30 to 50°C, RH 95% non-condensing
Dimensions
9.9 x 3.8 x 14.3cm (3.9 x 1.5 x 5.6in)
Weight
0.18kg (0.4lb)
Ordering Information
Model
Includes
MT Tracer Kit
MT Tracer Source, MT Tracer Display, batteries, instruction card, and carry case.
Test & Inspection
© 2002, AFL Telecommunications, all rights reserved. TRCR-00-2000 Revision C, 8.12.05
Specifications are subject to change without notice.
68
OFI-FTTx Active ONT Detector
The OFI-FTTx is a rugged, handheld optical fiber identifier designed to identify the
presence or absence of an active Optical Network Terminal (ONT) on FTTx F2 fibers at the
Fiber Distribution Hub (FDH). During a test the F2 fiber does not have to be removed from
service. Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected
to an active circuit before it is disconnected for fault location or re-use. The OFI-FTTx
can help verify FTTx network records and recover splitter pigtails and F2 fibers that are
connected at the FDH but, in fact, are available for new customers.
When applied to a splitter pigtail at the FDH, the OFI FTTx will report either that the ONT is
‘Active’ or ‘Not Detected’. Time to complete each test is typically one second.
The OFI-FTTx is compatible with 2mm jumper cable containing standard single-mode
fiber, such as SMF-28e ®, or bend insensitive fiber (BIF) with a 15mm bend radius
specification, such as AFL Bend Insensitive.
Features
•• Rugged, handheld, lightweight
•• In-service detection of upstream
(1310 nm) activity on FTTx networks
•• Determines which unparked splitter
pigtails are connected to ONTs
•• Does not require travel to customer
(ONT) site
•• Does not require disconnect of splitter
pigtails
•• Visual and audible indicators
•• Battery operated
•• Low battery indication
Ordering Information
Model
OFI-FTTx
Includes
OFI-FTTx, user's guide, and carry
case
Patent Pending
The OFI-FTTx is powered by two standard AA alkaline batteries, provides a low battery
indication, and can typically be operated 800 times before battery replacement is
necessary.
Applications
•• FACILITY RECOVERY: Harvest unparked splitter legs and F2 fibers not connected to subscribers.
•• TROUBLE-SHOOTING: Real-time confirmation of OLT to ONT connectivity at the FDH.
Specifications
Model
OFI-FTTx
Network Types
FTTx BPON, GPON, EPON, ≥ 1:4 splitter ratio
Network Locations
Between splitter and customer ONT
Fiber Type
2mm jacketed SMF-28e ®, 15mm bend radius AFL Bend Insensitive, and equivalents
Induced Loss (Typ)
< 1 dB @ 1550 nm
Test Time (Typ)
1 sec
Operating Range*
Loss from ONT to FDH: 0 to 7 dB (BPON), 0 to 9 dB (GPON, EPON)
User interface
Audio indicator and four red LEDs
Power
2 x AA batteries
Battery Life
800 tests typical
Operating Temperature
-10 to 40°C
Storage Temperature
-20 to 50°C
Dimensions (H x W x D)
22 x 3.8 x 3.2 cm (8.5 x 1.5 x 1.25 in)
Weight
0.23 kg (0.5 lbs)
* Maximum values are typical and depend on fiber type and jacket material.
© 2007-2009, AFL Telecommunications, all rights reserved. OFI5-10-2000 Revision E, 2009-12-11
Specifications are subject to change without notice.
69
OFI Optical Fiber Identifiers
Noyes Optical Fiber Identifiers are rugged, handheld, and easy-to-use fiber optic test
instruments designed to detect optical signals transmitted through a single-mode fiber
without disrupting traffic. During installation, maintenance, rerouting, or restoration; it is
often necessary to isolate a specific fiber. By simply clamping an Optical Fiber Identifier
onto a gently bent fiber, the unit will indicate if there is [No Signal], [Tone], or [Traffic] and
identify signal direction.
OFI 200
The OFI 200 model and OFI 400 model Identifiers are equipped with a unique two-position
head design that can be configured to work with 250 µm, 900 µm, ribbon, or jacketed
fiber in seconds, without tools or adjustments. When testing coated fibers, the slim design
of the OFI 200 and OFI 400 models allows easier access on a splice tray where the
amount of work space is limited. The clamping trigger is ergonomically designed to fit the
natural motion of the operator’s hand. A high impact molded plastic case makes the OFI
models suitable for use outside plant or in the central office.
The OFI 400 model is the next generation of Noyes Optical Fiber Identifiers. It has all the
features of the OFI 200 model plus easy-to-read LCD display with Backlight, multiple
[TONE] signal detection (270 Hz, 330 Hz, 1 kHz, or 2 kHz), power saving feature, and [Set
Reference] feature. The OFI 400 model also measures and displays fiber core power or
relative power on an LCD display.
Both models are battery operated with the battery indication feature and perform thousands of tests before batteries replacement is necessary.
Features
OFI 400
• Rugged, handheld, lightweight
• Accepts 250 µm, 900 µm coated fiber, 3 mm jacketed fiber cable, and ribbon fiber
• No head swapping or adjustments
• Identifies light carrying fiber
• Low insertion loss - traffic remains uninterrupted
• Indicates direction of traffic
• Indicates Tone signal visually and audibly
• 2 kHz Tone detection - OFI 200 models
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection - OFI 400 models
• Easy-to-read LCD display with Backlight - OFI 400 models
• Measures fiber core or relative power - OFI 400 models
• Power Off and Set Reference feature - OFI 400 models
• Battery operated
• Low battery indication
• Low cost, easy to use
continued on the next page
© 2002, AFL Telecommunications, all rights reserved. OFI1-11-2000 Revision 1E, 6.10.05
Specifications are subject to change without notice.
70
OFI Optical Fiber Identifiers
Applications
• Live fiber identification - used during
installation, maintenance, rerouting, or
restoration to positively identify fibers
prior to cutting and splicing
• Tone detection
• The OFI 400 models may also be used
for measuring core power or relative
power
Ordering Information
Model
Includes
OFI 200D
User's guide and carry case
OFI 400
User's guide and carry case
Specifications
Detectable signal range
Fiber Type
Parameter
250 μm coated fiber
(SMF-28 with 250 μm CPC6 coating)
1310 nm, CW or Traffic
Minimum detect level
1310 nm, Tone
(average power,
1550 nm, CW or Traffic
typical)
1550 nm, Tone
Wavelength, Signal
Insertion loss
(typical)
3 mm jacketed fiber
(SMF-28 with 250 μm CPC6 coating
and 3 mm, yellow jacket)
Optical Specifications
Model
1310 nm
1550 nm
1310 nm, CW or Traffic
Minimum detect level
1310 nm, Tone
(average power,
1550 nm, CW or Traffic
typical)
1550 nm, Tone
Insertion loss
(typical)
1310 nm
1550 nm
OFI 200D
OFI 200D
OFI 400
-40 dBm
-43 dBm
-45 dBm
-50 dBm
-45 dBm
-45 dBm
-50 dBm
-50 dBm
0.6 dB
2.5 dB
0.6 dB
2.5 dB
-30 dBm
-32 dBm
-33 dBm
-37 dBm
-30 dBm
-30 dBm
-33 dBm
-33 dBm
0.8 dB
2.5 dB
1.0 dB
2.8 dB
OFI 400
Detector type
InGaAs
Wavelength range
800 - 1700 nm
Calibrated size of fiber and wavelength
N/A
Fiber stress
250 µm (SMF-28) @1550 nm
<100 kPSI max
Fiber size
250 µm, 900 µm, 2 mm or 3 mm jacketed & ribbon fiber
Tone detection
2000 ±100Hz
270, 330, 1000, or 2000 Hz (±5%)
Core power measurement range
N/A
+13 dBm to – 50 dBm
SMF28/28E 250um @ 1550nm
Measurement units
N/A
dBm, dB
N/A
Multi 7 segment LCD; 3 LEDs;
1 piezo buzzer
General Specifications
Display Type
Power
Battery life
Operation temperature
1 x 9V Alkaline
2 x 1.5V Alkaline
>10,000 operations typical
>10,000 operations typical
0° to 50°C 90% RH (Non-condensing)
Storage temperature
-30 to +60°C 90% RH (Non-condensing)
Dimensions (H x W x D)
8.5 x 1.5 x 1.1 in. (22 x 3.8 x 2.8 cm)
Weight
7.5 oz. (210 g)
6 oz (168 g)
Notes:
1 250 µm coated fiber parameters are specified with OFI plunger in the “250/900/RIB” position.
2mm/ 3mm jacketed fiber parameters are specified with OFI plunger in the “2 mm/ 3 mm” position.
2 Unless noted otherwise, all specifications are typical. Actual results can vary by several dB depending on fiber type, coating material, jacket color, jacket hardness, and other factors.
All specifications stated above are as measured at 25°C.
3 [CW] is a light signal that is not modulated.
[Traffic] is a light signal modulated by a random data sequence.
[Tone] is a light signal modulated into a nominal 50% duty cycle square wave.
© 2002, AFL Telecommunications, all rights reserved. OFI1-11-2000 Revision 1E, 6.10.05
Specifications are subject to change without notice.
71
OFS 300 Optical Fiber Scope
The Noyes OFS 300 from AFL Telecommunications is a versatile Optical Fiber Scope with
precision 200X magnification. This handheld and rugged scope is used for inspection of
optical fiber connectors for scratches, dirt, or other problems normally associated with
poor transmission performance.
A built-in laser safety filter provides > 40 dB IR protection to reduce risk of injury to the eye if
accidentally viewing an active fiber.* The OFS 300 features a universal adapter cap mount
that accepts a variety of Noyes thread-on style adapter caps (ordered separately) to ease
inspection of many connector style. A momentary power switch located on the top panel
keeps one hand free for focusing.
The OFS 300 offers 60 hours of continuous battery life from standard 2 x AA batteries and
features an LED indicator, which will flash when barriers require replacement.
Features
•• Laser safety filter installed*
•• Precision 200X zoom
•• Universal adapter interface
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline
•• Tripod mount
•• Rugged, handheld, easy to use
*Always follow your company’s laser safety procedures and never use an optical microscope to view live fiber optic connectors.
Specifications
Optical Specifications
Nominal magnification
Adapter mount
Safety filter
200X
Universal, thread-on
Schott KG3, > 40 dB IR
General Specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +50°C
Power
2 x AA batteries
Battery life
> 60 hours
Weight in use
0.67 kg (1.5 lbs)
Size (H x W x D)
13 x 5 x 20 cm (5 x 2 x 8 in)
Ordering Information
Model
Includes
OFS 300
OFS 300 Inspection Scope, 2 x AA batteries, neck strap, 2.5 mm universal
adapter cap, and user’s guide
© 2002-2008, AFL Telecommunications, all rights reserved. OFS1-00-2000 Revision T 07.30.08
Specifications are subject to change without notice.
72
VS 300 View Safe Inspection Scope
The VS 300 Video Fiber Scope removes concerns for eye safety while inspecting optical
fiber connectors. The design eliminates the optical path to the eye by utilizing a miniature
camera and a state-of-the-art micro-display that achieves unparalleled clarity and
resolution.
The VS 300 is modeled after the functionality of our highly successful OFS 300 product
line with the following improvements:
• The VS 300 has no optical path to the user’s eye.
• The VS 300 has NTSC video output.
• The VS 300 has the familiar shape and control positions of the OFS 300 but is half the
weight and has a molded easy grip case with easy access battery compartment.
Features
• Video Technology
• No optical path to your eye
• 400X magnification
• Resolves ¾ micron scratches
• Universal Adaptor Interface with new
"pan and lock" centering mount
• Video Output
The magnification of the unit is equivalent to 400X (23-degree field of view comparable
to 8” monitor viewed at a distance of 20”) and provides 600X when its video output is
displayed on a 12” monitor. The unit uses all the OFS 300 adaptor caps and has an energy
saving automatic shutoff.
Specifications
Optical Specifications
Magnification
400X equivalent to 8” monitor for 20” distance, 600X on 12” monitor
Adaptor mount
Thread-on (Universal)
Safety filter
Not Required - No optical path to user
Video output
NTSC
General Specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +60°C
Humidity
0 to 90% (non - condensing)
Power supply
2 AA alkaline batteries, optional AC adapter
Battery life
10 hours continuous
Indicators
Low battery
Weight
0.94 lbs (0.42 kg)
Size (H x W x D)
3.5 x 1.5 x 8.5 in (8.9 x 3.8 x 21.6 cm)
Ordering Information
Model
Includes
VS 300
VS 300 Inspection Scope, 2 x AA batteries, neck strap, 2.5 mm universal adapter cap, and
user’s guide
© 2002, AFL Telecommunications, all rights reserved. VOS3-00-2000 Revision D 8.03.05
Specifications are subject to change without notice.
73
VFS 2 Video Fiber Scope 2nd Generation
The VFS 2 is a small versatile video fiber scope, which retains the superior image quality
associated with Noyes inspection products. The unique “optical-knuckle” allows the user
to orient the probe head in virtually any direction. This feature allows the user to view
connectors that may be located in tight or difficult locations. With a probe head length of
less than 8 cm (3.25”), access into crowded/cramped quarters becomes a reality.
The VFS 2 resolves ¾ micron scratches, keeping with our standard of quality end-face
images. This unit is designed for one-handed operation and with the “optical-knuckle”
feature, the unit is equally easy for both right and left handed individuals.
Features:
• Unparalleled access to connectors and
bulkhead adapters
• One-handed operation
• Resolves ¾ micron scratches
• Precision adapter tips for easy centering
• 350-micron field of view (diagonal)
• Smooth, precision focusing (left or right
handed)
• Advanced lithium ion battery
The VFS 2 probe may be paired with the VFS 2 high-resolution 3.5” Display unit.
Also, the VFS 2 Inspection Probe may be used with the VCP 1 Video Capture Port, which
allows the user to inspect fiber optic end-faces and capture viewed images on a PC.
Specifications
Optical Specifications
Field of view
350 microns diagonal (208 μm vertical, 285 μm horizontal)
Magnification
250X on 3.5” display
Resolution
¾ micron scratch
Video Output
NTSC
VFS 2 Probe Specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +60°C
Humidity
0 to 90% (non-condensing)
Probe weight
0.4 lb (0.2 kg)
Probe body size (L x W x D)
6.3 x 1.3 x 1.3 in (15.9 x 3.3 x 3.3 cm)
Probe head size (with FC adapter), (L x W x D)
3.1 x 1.0 x 0.6 in (7.9 x 2.5 x 1.5 cm)
VFS 2 Display specifications
Display Screen Size
3.5 inch TFT NTSC
Display package with protective boot size
9.0 x 2.0 x 4.7 in (22.9 x 5.1 x 11.9 cm)
Weight
2 lb (0.9 kg)
Power
Li-Ion battery pack or AC adapter
Battery life with VFS2 probe
> 4 hours
Operating temperature
0° to 50° C
Storage temperature
-20 to +60°C
Humidity
0 to 90% RH non-condensing
Li-Ion battery pack charging temp.
-10 to +45°C
Li-Ion battery pack recharging time
4 hours
Ordering Information
Model
Includes
VFS2-00-0900
VFS2 Probe, VFS 2 LCD Display unit (3.5” (9 cm), AC adapter, and user's guide.
VFS2-00-0903
VFS2 Probe, VCP1 USB interface and basic software (requires computer with display), and
user's guide.
© 2004-2007, AFL Telecommunications, all rights reserved. VFS2-00-2000 Revision B, 5.22.07
Specifications are subject to change without notice.
74
VCP 1 USB Video Capture Port
The VCP 1 Video Capture Port is an interfacing module that provides high-speed composite
video signal to a digital format conversion for capturing and displaying video data on a PC.
The VCP 1 simply attaches via a standard USB connector to you computer and offers “plug
and play” installation.
fiber end images displayed on a PC
When used in conjunction with the VFS 2 probe or VS 300 video microscope, the VCP 1
Video Capture Port allows you to inspect fiber optic end-faces and capture viewed images
on your computer. With the supplied easy-to-use Windows software, fiber end images can
be saved and organized for analyzing, printing, and archiving.
The VCP 1 front panel includes the video capture button - [Snap Shot] for single shot video
capture and the [Active] LED, which indicates that the unit is operating.
Batteries or an AC adapter are not required; the VCP 1 power is supplied via the USB connection. The VCP 1 is ideal for laptop or desktop use.
The VCP 1 package Includes: VCP 1 unit, CD-ROM with driver and software, and user’s guide.
System Requirements
VCP 1
Features
• Compact size
• Captures fiber end images directly into
your computer
• Includes Includes “Video Capture”- Windows®-based software
• Converts analog video signal from Noyes
RJ11 input to digital via USB A plug
• Supports NTSC or PAL system
• No battery - no need to install batteries
or run off the AC adapter
• Low power consumption
• A single snap shot button takes still
images at VGA solution (640 x 480
pixels)
• Low CPU utilization at decompression
• Plug and play installation
• A 400 MHz (or faster) PC or laptop with
USB 1.1 or better
• At least 800 x 600 SVGA display
• Windows 2000 or XP
• At least 128 MB of RAM
• A CD-ROM drive
Specifications
Interface Type
USB
Operating system
Windows 2000 and XP
Video input
Noyes RJ11 connector
Output
USB Standard (VCP 1 is a Twain compatible device using supplied software)
Analog video format
NTSC or PAL
Video capture resolution
640 x 480 pixels
Snap shot
Single button to capture still images at 640 x 480 pixels
Video capture format(s):
JPEG
Power source
5VDC @500 mA (max) through USB port to 6 foot cord
USB data bandwidth
4Mbps - 8Mbps isochronous
Weight
0.25 lb (0.11 kg)
Size (L x W x D)
4.0 x 2.2 x 1.0 in (10.2 x 5.6 x 2.5 cm)
For more information concerning Noyes fiber optic products and accessories please call 1-800-321-5298.
© 2003, AFL Telecommunications, all rights reserved. VCP1-00-2000 Revision 1E 9.12.05
Specifications are subject to change without notice.
75
FTS Series Fiber Optic Talk Sets
Fiber Optic Talk Sets are an inexpensive solution to meet your communication needs when
testing multimode or single-mode fiber optic cables. Designed for voice communication
over spare fibers, they provide full duplex, hands-free operation. Ease of use and compact
size allow the operators to focus on the task at hand, rather than operating the talk set.
FTS 1
FTS 2
Two talk set models are available, the FTS 1 for communication on single-mode or
multimode fiber and the FTS 2 for long-range single-mode applications. The FTS 2 model
includes a multiparty communication feature, which provides the connection of two talk
sets at a common site to extend the range or to include three or more persons in the
conversation.
FTS-20C Clip-on Coupler
A clip-on coupler is available for bare fiber access where terminated ends are not
available. The FTS 20C allows bi-directional communication from the center point on a
fiber link or from the unterminated end. When used with a fiber talk set, such as the FTS2,
the user can access the intended talk fiber at the mid-point across the span, usually at
the splice enclosure. The FTS-20C can also be used in conjunction with a laser source or
a tone detector to inject or detect 2 kHz test tones. It works at 1310, 1550, or 1625 nm.
Coupling efficiency is approximately 18 dB.
FTS-20C
Specifications
Features
•• Single fiber, full duplex
•• Multimode and single-mode models
•• Field portable, hands-free operation
•• Automatic connection
•• Multiparty communication
•• Digital technology
•• Call-back feature/ringing (FTS 2 model)
•• Communicates with T500B talk option
(FTS 2 model)
Ordering Information
Model
Includes
FTS 1
FTS 2
Protective rubber boots, batteries,
headsets, manual, and carry case.
Fiber optic talk sets are purchased
in pairs. Two units are required for
communication.
Model
Optical Specifications
FTS 1-2
FTS 2-1310
FTS 2-1550
Wavelength
1300 nm
1300 nm
1550 nm
Dynamic Range MM/SM
12 dB / 20 dB
45 dB
45 dB
Distance Range (km)
Typical 62.5 or 50µm MM fiber1
Typical 1310 nm-optimized SM fiber2
Typical 1550 nm-optimized SM fiber3
>10
50
40
N/A
113
90
N/A
150
180
Fiber Type
MM/SM
SM
Connector
FC, SC, ST
FC, SC, ST
Emitter Type
LED
Laser
Emitter Classification
General Specifications
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Power
9V alkaline
4 AA alkaline or AC adapter
Weight in Use
0.25 kg (0.56 lb)
0.52 kg (1.16 lb)
Size (H x W x D)
16.8 x 7.9 x 3.8 cm
(6.6 x 3.1 x 1.5 in)
18.5 x 11.1 x 4.6 cm
(7.3 x 4.4 x 1.8 in)
Operating Temperature
0° to +50° C, RH 0 to 90% non-condensing
Storage Temperature
-20° to +50° C, RH 0 to 90% non-condensing
Notes:
1 2.8 dB/km @ 850 nm, 0.6 dB/km @ 1300 nm.
2 0.4 dB/km @ 1310 nm, 0.3 dB/km @ 1550 nm.
3 0.5 dB/km @ 1310 nm, 0.25 dB/km @ 1550 nm.
© 2002-2009, AFL Telecommunications, all rights reserved. FTS2-00-2000 Revision J, 2009-08-04
Specifications are subject to change without notice.
76
SVA 1 Singlemode Variable Attenuator
The SVA 1 Singlemode Variable Attenuator advances fiber optic field testing by offering
superior performance in a low cost hand-held package. Utilizing a simplified, industry
accepted attenuation technique, the innovative design of the SVA 1 offers superior resolution across the entire 60 dB dynamic range.
Intended for field testing during installation, new equipment turn-ups, or routine maintenance, the SVA 1 is a complete, easy to use attenuator. Its unique features allow bidirectional signal transmission with no loss penalty.
The SVA 1 is available with a variety of connectors and reflectance options to better than
60 dB. With only two adjustments, COARSE and FINE, the SVA 1 is simple to understand
and operate. The SVA 1 is suited for all singlemode applications including Telco, LANs,
WANs, Video, and CATV.
Features
• 1310 and 1550 nm single-mode
• Lightweight
• Coarse and fine adjustments
• 60 dB dynamic range
• Better than 60 dB isolation available
• FC, SC, or ST Style Outputs
• Low insertion loss
Specifications
Optical Specifications
SVA 1
Wavelengths
Insertion Loss
Minimum Attenuation
Return Loss
1310 nm & 1550 nm ± 30 nm
≤ 1.5 dB @ 1310 nm
60 dB
50 dB (≥ 60 dB optional - angled FC)
Coarse Adjustment
Fine Adjustment
Connector
General Specifications
Operating Temperature
Storage Temperature
Size (H x W x D)
Weight
0 to 60 dB nominal
0 to 10 dB nominal
FC, ST, SC
-10 to +55°C
-30 to 60°C
5.5 x 2.75 x 1.5 in (14 x 7 x 3.8 cm)
6 oz. (168 grams)
© 2002, AFL Telecommunications, all rights reserved. SVA1-00-2000 Revision J, 9.15.05
Specifications are subject to change without notice.
77
VOA5 Variable Fiber Optic Attenuator
The Noyes VOA5 from AFL Telecommunications is a handheld variable optical attenuator
suited for a wide range of fiber link certification and production test applications. Two
models are available, the VOA5-MM multimode and the VOA5-SM single mode model. The
VOA5 attenuator offers high bi-directional return loss and will maintain the set attenuation
level when the unit is powered down.
Input/output ports of the VOA5 are equipped with tool-free removable adapters to allow
the output connectors to be inspected and cleaned. The VOA5 is powered by two (2) AA
alkaline batteries or an AC power adapter. A NiCad rechargeable battery pack is available
as an option.
Specifications
Optical
VOA5-MM
VOA5-SM
Fiber Type
62.5 µm, multimode
9 µm, single-mode
Wavelength Range
850 - 1300 nm
1290 - 1620 nm
Calibrated Wavelengths
850, 1300 nm
1310, 1550 nm
0 to 30 dB
0 to 60 dB
1.5 dB @ 850 nm
3.0 dB @ 1300 nm
3.0 dB
Features
Attenuation Range
•• Multimode and single-mode models
•• High speed (0 to 60 dB < 3 seconds)
•• 2 x AA alkaline, AC power, or optional
NiCad battery pack
•• Long battery life (> 16 hours)
•• Handheld, rugged, lightweight (0.55 kg)
•• Cost-effective, easy to use
Insertion Loss (max.)
Return Loss (min.)
20 dB
40 dB
Display Resolution
0.1 dB
Accuracy @+25ºC
±0.20 dB typical, ±0.4 dB max (0 dB to 30 dB)
±0.3 dB typical, ±0.6 dB max (30 dB to 60 dB)
± 0.25 dB*
Repeatability @+25ºC
Maximum Input Level
General
± 0.45 dB*
+ 24 dBm
VOA5-MM
VOA5-SM
10 hours
> 16 hours
0 to 30 dB in less than 5 seconds
0 to 60 dB in less than 3 seconds
Battery Life (2 x AA alkaline)
Speed
Power
2 x AA alkaline, AC adapter, or NiMH battery pack (optional)
Size (H x W X D)
18.5 x 11.1 x 4.6 cm (7.3 x 4.4 x 1.8 in.)
Weight
0.55 kg (1.22 lb)
Operating Temperature
0° to +50° C
Storage Temperature
-20° to +60° C
Relative Humidity
0 to 90% (non-condensing)
Available Connectors
SC/UPC, FC/UPC, ST/UPC
* Repeatability is defined as the mean plus one standard deviation typical value.
Ordering Information
Model
Includes
All VOA5 models
Protective rubber boot, 2 x AA alkaline batteries, 120/ 220 V AC power adapter*, manual, and
carry case.
* Specify optical connector and AC power cord type.
© 2002-2008, AFL Telecommunications, all rights reserved. VOA5-00-2000 Revision C, 11.20.08
Specifications are subject to change without notice.
78
Network Simulators - Models NS1 and NS2
NS1/ NS2 fiber optic network simulators are custom-designed “fiber boxes” intended to
duplicate installed fiber optic facilities. Training schools, laboratory bench design, or field
troubleshooting are just few of the many applications for these portable units.
Both models may be supplied with customer-specified lengths of multimode or singlemode fiber. Fusion or mechanical splices may be included at various points within the fiber.
A full range of panel-mount connector types is available including SC, ST, FC, and LC.
Connectors may be angled or non-angled with user specified polish. NS1/ NS2 network
simulators come fully characterized for loss, attenuation/km, and splice location/value.
Each network simulator is housed in rugged field-portable case. The compact NS1
accommodates up to 3 km of fiber. The larger NS2 accommodates up to 15 km of optical
fiber. Optional travel cases are available to accommodate single or multiple units along
with accessory cables, tools, etc.
Features
• User-specified fiber type
• Custom designed lengths
• Mechanical or fusion splices available
• OTDR trace is provided
• SC, ST, FC, LC and other panel connectors are available
• Rugged, field-portable
Test & Inspection
© 2002, AFL Telecommunications, all rights reserved. 0461-00-2000 Revision C, 8.12.05
Specifications are subject to change without notice.
79
Network Simulators – Models NSR
NSR fiber optic network simulators are custom-designed rack-mountable boxes intended
to duplicate installed fiber optic facilities. Training and laboratory testing are just a couple
of the many applications for these units.
Network simulators may be ordered with customer-specified lengths of multimode or
single-mode fiber. Events such as connections, fusion splices, and mechanical splices
can be added at various points within the fiber to duplicate installed networks. A variety of
connectors types are available. Each network simulator come with full documentation for
insertion loss, attenuation/km, and event location/value.
The NSR models are housed in either 18 or 23 inch rack-mountable boxes. These network
simulators can accommodate multiple lengths of fiber and hold a total of 100 km of fiber.
Features
• User-specified fiber type
• Custom designed lengths
• User-specified events
• OTDR trace provided for documentation
• Variety of connector styles available
• Rack-mountable
• Accommodates up to 100 km of fiber
• N.I.S.T. Traceable
Test & Inspection
© 2002, AFL Telecommunications, all rights reserved. NSR1-00-2000 Revision 1B, 8.12.05
Specifications are subject to change without notice.
80
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement