Clifford CONCEPT MILLENNIA Car Alarm System Installation manual

Add to My manuals
20 Pages

advertisement

Clifford CONCEPT MILLENNIA Car Alarm System  Installation manual | Manualzz

Standard Features of the Concept 600

q

Lifetime Warranty

q

His & Hers Remote Controls

q

ACG™ 2 (Anti-CodeGrabbing™)

q

Extended Range Receiver

q

Audible Low-Battery Warning

q

Built-In Two-Point Immobilizer™

q

Optional Wireless Immobilizer™

q

Dual-Zone OmniSensor

q

Digital Dual-Zone Proximity Sensor 4

q

Patented UltraSecure Coded Valet Mode™

q

NightVision™ Headlight Automation

q

Auto mat ic Post- Parking Il lu mi na tion

q

Built- In Re mote Head light Ac ti va tion

q

Eight-Event TotalRecall™

q

Enhanced User-Selectable AutoArming

q

Built-In Window RollUp

q

User-Selectable Remote Valet Mode Entry/Exit

q

Built-In BlackJax Anti-Carjacking System

q

Optional DataPort™ Interface and CliffNet Wizard

Pro™ Software

q

FACT — False Alarm Control and Test

q

Prewired LED, Sensor, Siren, Extended Range Receiver and PlainView 2 Switch Connectors

q

High Output Medallion Siren

q

Dual-Mode “Chirp” Silencing

q

Remote Siren Silencing

q

Remote Door Locking/Unlocking with Built-in Relays

q

User-Selectable AutoLock

q

User-Selectable AutoUnLock

q

Integrated Electronic Timer

q

Turbo Timer Output

q

CliffNet DataPort Accessory Interface

q

Remote Keyless Entry and Accessory Activation Even in

Valet Mode

q

Remote Panic with Smart Locking/Unlocking

q

Smart Remote Trunk Release

q

Built-In Dual Parking Light Flasher with Onboard Relay

q

Remote-Controlled Courtesy Lighting

q

Patented Smart AutoTesting™

q

Patented Malfunction AutoBypass™ with

AutoReMonitoring

q

Patented Smart Prior Intrusion Attempt Alert

q

Patented Remote Control Code Learning and MultiRemote

Recognition

q

Clear All Remotes

q

Multiple-Car Control

q

High-Luminescence LED Status Indicator with Automatic

Battery-Saving Mode

q

Multiple Sensor/Trigger Inputs

q

Patented SmartPowerUp™ 2

q

Full-Time SecureAccess™ Programming

q

Advanced CMOS Microcomputer

q

Pre-Loomed Wiring

q

Three Auxilliary Outputs with Selectable Output Types

q

AutoActivation of Auxilliary Output C for Window

All-Close

q

Installer-Selectable Door Ajar/Delayed Courtesy Lights

System Components

The Concept 600 kit contains the following components:

One Prewired 24-pin Connector Harness

One Prewired 14-pin Connector Harness

One Concept 600 Control Unit One Hardware Kit

One Digital Dual-Zone Proximity Sensor 4

One Dual-Zone OmniSensor

One NightVision Light Sensor

One Extended Range Receiver

One PlainView 2 Coded Valet Switch

One Self-Powered SmartSiren 4

One User’s Manual

Two Remote Transmitters

Two Window Decals

One LED Status Indicator

Con cept 600/199

1

2

Pin Col our

1 Red/White

2 White/Orange

3 Violet

4 White/Violet

5 Red

6 White/Green

7 Red/Black

8 Green/Blue

9 Orange

10 White/Blue

11 White/Brown

12 Brown

Pin Col our

2 Blue/White

5 Blue

6 White/Orange

7 White/Green

8 Red/White

9 Brown/Red

10 Gray

11 Red/Orange

12 Red/Green

13 Gray/Green

14 Gray/Orange

Wiring Description for the 12-Pin Connector

Con nects to

Headlight input (+) or (-)

Window switch 2 input

Window motor 1 output

Window switch 1input

Window supply input (+)12V

Key side starter (+) 12V

Headlight output (+) or (-)

Coil side ignition (+)

Window motor 2 output

Starter side starter (+) output

Key side ignition input (+)

Parking light output (+) 12V

Wiring Description for the 14-Pin Connector

Con nects to

Brake input/output (+) 12V

Windshield wiper input (+)

Door unlock common

Door lock common

Parking and brake light input (+) 12V

Interior light supply (+) or (-)

Door trigger input (+) or (-)

Door unlock normally open

Door lock normally open

Door lock normally closed

Door unlock normally closed

Con cept 600/199

Con cept 600/199

3

4

Pin Col our

2 Red/Black

3 White/Blue

4 Violet

5 Black/Gray

6 Red

7 Blue/Yellow

8 Gray/Yellow

9 Black

10 Black

11 White

12 Gray twinlead

13 Gray/Violet

14 Gray/Blue

15 Gray/Red

17 Yellow

18 Red

19 Black twinlead

20 Green

21 Black twinlead

22 Gray twinlead

23 White/Black

24 Orange

Wiring Description for the 24-Pin Connector

Con nects to

Optional Digital OmniSensor input (5V+)

Prewired Digital Proximity Sensor input connector

LED Output (+) 12V

Ignition coil or tach input

Proximity Sensor and Tilt Sensor power supply (+) 12V

Windshield wiper input (-)

Trunk trigger switch input (-)

Sensors, LED and valet switch ground supply (-)

Ground

Valet Switch input (-) multi-plex

Light sensor input (NightVision)

Auxilliary Output A output

Auxilliary Output B output

Auxilliary Output C output

Optional airhorns or siren output (-)

Battery input (+) 12V

Not used

Tilt Sensor armed output

Not used

Light sensor input (NightVision)

Hood trigger switch input (-)

Tilt Sensor input (-)

Con cept 600/199

Con cept 600/199

5

Passenger Compartment Connections

Control Unit and Extended Range Receiver

The Concept 600 con trol unit must be in stalled in side the ve hi cle. Un der no cir cum stances should the unit be in stalled un der the hood or other simi larly hos tile en vi ron ment.

1. Select an area behind the dash to mount the control unit using the supplied wire tires, but do not permanently affix it until all wiring and testing is complete.

2. Plug the extended range receiver in to the control unit. Mount the extended range receiver away from the control unit and run the antenna either up the window pillar and affix it to the windshield, or under the dash, away from metal. The position and location of the receiver will effect remote control range. Do not fold the excess cable or antenna wire. Do not make hard, sharp bends.

Door Trigger/Interior Light Supply

Please refer to the Door Trigger/Interior Light Supply section in this binder for information on polarity testing and connections.

Central Door Locking System

Please refer to the Door Locks section in this binder for information on circuit types and connections.

LED Status Indicator

Select a prominent location on the dash or console visible through all windows. Discuss placement with the owner.

1. Verify there is adequate space to accommodate the LED, then drill a 5/16” (8mm) hole and route the wires through it.

2. Mate the LED connectors to the VIOLET and BLACK wire connectors as shown in the diagram on page 3.

3. Press the LED into place.

PlainView 2 Coded Valet/Programming Switch

1. Discuss placement of the switch with the vehicle owner and avoid placing the switch where it can be pressed accidentally.

2. Verify there is adequate space behind the selected location to accommodate the switch.

3. Drill a 5/16” (8mm) mounting hole, then insert the wires through the hole.

4. Mate the switch’s locking connectors to the WHITE and BLACK locking connector.

5. Remove the adhesive backing and press the switch into place.

NightVision Headlight Illumination

1. Mount the Light Sensor in a discreet location on the dashboard. The light sensor must be positioned in such a way that the light

“eye” can detect light coming through the windshield.

2. Plug the BLACK twin lead wires from the light sen sor into the GRAY twin lead wires from the 24- pin con nec tor, using supplied butt connectors, and then crimp the wires together.

3. Using a DVM, test the wiper switch output line going to the motor. If the polarity is positive when you turn the windshield wipers on, connect the BLUE wire to the line between the wiper motor and the wiper switch. If the polarity is negative, connect the

BLUE/YELLOW wire to the line between the wiper motor and the wiper switch as shown on page 3. Insulate (tape) the used wire.

4. Locate the wire at the headlight switch that changes voltage when the headlights are turned on. Connect the RED/BLACK wire to this line. If the line indicates positive whilst the headlights are on,connect the RED/WHITE wire to power. If the line indicates negative whilst the headlights are on, connect the RED/WHITE wire to ground.

6

Con cept 600/199

Passenger Compartment Connections (Continued)

Remotely Adjustable Dual-Zone Proximity Sensor

This efficient new-generation proprietary radar sensor is immune to the wind and temperature variations that cause ultrasonic sensors to false alarm. The sensor must be mounted onto a metal surface and face outward into the passenger compartment. It should be positioned as close as possible to the centre of the passenger compartment. Suggested mounting locations include within the centre console, behind the dash, under the carpeting of the central hump or even in the headlining. When selecting a location, keep in mind that metal as well as metallic paint, metallic-coloured plastic and metal-laced window tint material will interfere with the radar field. Be certain not to mount the sensor under a location where the vehicle owner may store coins, CDs or cassettes

(iron-oxide tape). The radar waves of the sensor will pass through nonmetallic materials such as plastic, fabric and carpet.

1. Temporarily affix the sensor where it will be mounted, but do not yet permanently mount it until after adjusting and testing sensitivity (the sensor may need to be relocated, so do not permanently secure it until it has been thoroughly tested).

2. Join the Proximity Sensor to the connector with the BLACK, WHITE/BLUE and RED wires, then secure the wires with a cable tie.

Dual-Zone OmniSensor

Trunk Trigger

Vehicles with a ground-switching trunk light will interface directly with the Concept 600 (on positive switching vehicles, use a relay to invert polarity). The switch may be located in or near the trunk latch or at the trunk light. If a switch cannot be located, you must add a pin switch in a location away from water channels.

NOTE: If the ve hi cle has a dash board trunk ajar in di ca tor, in stall a 1- amp di ode be tween the light and switch with the di ode band point ing to ward the switch.

1. Connect the GRAY/YELLOW wire to the trunk switch (between the diode and switch if you added a diode).

Brake Switch

The brake switch connection is required for the operation of the Concept 600’s anti-carjacking electronics.

1. Turn the ignition to the “ON” position and press the brake pedal to verify that the brake lights are operational.

2. Find the one wire that carries +12V when the brake pedal is pressed, then connect the BLUE/WHITE wire to this wire.

Parking Lights

See the Door Trigger/Parking light section in this binder.

Starter and Ignition Immobilization Circuits

1. Locate the ignition switch wireloom under the dash and use a voltmeter to locate the one wire that carries +12V throughout

BOTH the cranking AND engine running cycles, and 0 volts when the ignition is off.

2. Start the engine, then cut the ignition wire. The engine should stop running.

3. As shown on page 5, connect the WHITE/BROWN wire to the key side of the cut ignition line.

4. Connect the GREEN/BLUE wire to the engine side of the cut ignition line.

5. Use a voltmeter to locate the one wire that carries +12V during the cranking cycle ONLY. Cut this wire, then try to start the engine. It should not crank.

6. Con nect the WHITE/GREEN wire to the key side of the cut starter line.

7. Connect the WHITE/BLUE wire to the engine side of the cut starter line.

NOTE: The starter cir cuit may carry a very high cur rent. Be cer tain that the starter wire con nec tions are solid.

Con cept 600/199

7

Passenger Compartment Connections (Continued)

Auxilliary Output A with Selectable Output Type

The output (GRAY/VIOLET wire) can be programmed as either pulsed, latched or timed and can be programmed to operate only when the system is disarmed (e.g., for use as a remote trunk release). The output is activated by transmitting channel 2 from the 16channel master remote control. The factory setting is pulsed output (0.5 second ground). The latched output stays at ground until channel 2 is activated a second time, and the timed output stays at ground for any selected duration between one second and four minutes. Current is limited to 0.15 amp. See Installer-Programmable Features on page 16 for information on programming the output type and/or disabling operation whilst the system is disarmed.

Auxilliary Output B with Selectable Output Type

The output (GRAY/BLUE wire) can be programmed as either pulsed, latched or timed and is activated by transmitting channel 7 from the 16-channel master remote control. The factory setting is pulsed output (0.5 second ground). The latched output stays at ground until channel 7 is activated a second time, and the timed output stays at ground for any selected duration between one second and four minutes. Current is limited to 0.15 amp. See Installer-Programmable Features on page 16 for information on programming the output type.

Auxilliary Output C with Selectable Output Type and AutoActivation

The output (GRAY/RED wire) can be programmed as either pulsed, latched, or timed and in addition, can also be programmed to automatically activate every time the system is armed using the remote control. The output is activated by transmitting channel 8 from the 16-channel master remote. Current is limited to 0.15 amp. AutoActivation is perfect when programmed as a timed-output to close the power windows and sunroof on vehicles that have an all-close feature. See Installer-Programmable Featureson page 16 for more information on programming output type and/or enabling the AutoActivation feature.

Window RollUp

Please refer to the Window RollUp section in this binder for information on the various circuit types and connections.

Engine Bay Connections

High Output Medallion Siren

Mount the siren in the engine compartment away from hot or moving parts and where it cannot be reached from under the vehicle, preferable opposite the exhaust system. Point the siren down to avoid water collection (see the illustration).

1. You must firmly secure the siren to the engine bay firewall or an fender well using all three sheet metal screws supplied.

2. Us ing the sup plied con nec tor, fasten the GRAY twin lead wire coming from the siren to the BLACK twinlead from the 24-pin connector on the control unit.

RPM Monitoring

This is required for both RPM-activated automatic door locking and for BlackJax anti-carjacking features. See the RPM Monitoring section in this binder for information.

Hood Trigger

Vehicles with a ground-switching hood pin switch interface directly with Concept 600 (on positive switching vehicles, use a relay to invert polarity). If a switch cannot be located, you must add a pin switch in a location away from water channels.

1. Connect the WHITE/BLACK wire to the hood pin wire (between the diode and pin switch if a diode was added).

Final Wiring Connections

1. Connect the 18 AWG RED wire to the 5-amp fuseholder as shown on page 3.

2. Connect the 14 AWG RED wire from the 12-pin connector to the 30-amp fuseholder as shown on page 5.

3. Connect the 18 AWG RED/WHITE wire to the 20-amp fuseholder as shown on page 5.

4. Attach the three fuseholders to the battery positive cable clamp.

5. Attach the AWG BLACK wire to the battery negative cable clamp.

NOTE: Power and test ac ces so ries af ter the ba sic sys tem has been tested. In di vidu ally fuse all ac ces sory power con nec tions. In di vidu ally fuse all +12V fuse panel con nec tions.

8

Con cept 600/199

SmartPowerUp™ 2

SmartPowerUp 2 ensures that the system powers up in the same state (disarmed, armed or valet mode) it was in when power was removed.

When you first power up the Concept 600, it will silently enter the disarmed state.

Delayed Courtesy Lights

Some vehicles have a courtesy light delay or dimming circuit, which interferes with an alarm being able to detect the door trigger upon remote arming. If the delay or dimming lasts more than 5 seconds, no special connections or testing are needed, simply turn on the Delayed

Courtesy Lights feature as noted in the Installer-Programmable Features section on page 16. Please note that since this feature sets the system to arm the instant the courtesy lights turn off, the Door Ajar Warning feature will not be available.

Mandatory RPM Programming

NOTE: This MANDATORY programming step must be completed for the Concept 600 to operate properly.

1. Drive the vehicle to a nearby open area and allow the engine to warm-up until the RPMs drop to the normal idle speed.

2. With the engine still running, place the transmission in Park (or Neutral if the vehicle has a manual transmission).

3. Enter the code of “2” valet code using the instructions provided in the Programmable Features on page 14. The LED will briefly illuminate. Press and hold the ✱ button for 10 seconds (you will hear one confirmation chirp after three seconds—do not stop holding the button—continue holding the button until you hear a three-chirp confirmation). Release the button.

4. Press the unmarked button once. After a three-second pause, the system will sound one chirp to confirm column one selection

(see the Installer-Programmable Features section on page 16).

5. Press the ✱ button five times (you will hear a chirp each time you press the button) to select row five. After a two-second pause, you will hear two chirps to confirm idle RPM has been set (if you hear just one chirp, check the connection of the BLACK/GRAY wire, then repeats steps 1 - 5).

6. Turn the ignition OFF.

Remote Control Operation

The Concept 600 comes with two ergonomically designed remote controls: a 16-channel master remote and a 10-channel secondary

“companion” remote. Up to two more ACG 2 remote controls can be added to the Concept 600 system. Due to the ACG 2 feature on the IntelliGuard Series systems, older Clifford ACG and non-ACG remotes are not compatible with the Concept 600.

16-Channel Mas ter Re mote Con trol Op era tion

To transmit either channel 1, 2, 3 or 4: Press button 1, 2, 3 or 4. The LED indicator on the remote control will flash once every second: this indicates level 1.

To transmit either channel 5, 6, 7 or 8: Press the LevelShift button once. This shifts buttons

1–4 to level 2 (channels 5–8). Then press the desired button within the next 7 seconds. For instance, to transmit channel 5, press the LevelShift button once, then press button 1. The

LED indicator on the remote control flashes twice, pauses, flashes twice, etc.: this indicates

level 2.

To transmit channel 9, 10, 11 or 12: Press the LevelShift button twice. This shifts the buttons to level 3 (channels 9–12). Then press the corresponding button within the next 7 seconds. For instance, to transmit channel 10, press the LevelShift button twice, then press button 2. The LED on the remote control flashes three times, pauses, flashes three times, etc.: this indicates level 3.

To transmit channel 13, 14, 15 or 16: Press the LevelShift button three times. This shifts the buttons to level 4 (channels 13–16).

Then press the corresponding button within the next 7 seconds. For instance, to transmit channel 14 press the LevelShift button three times, then press button 2. The LED on the remote control flashes four times, pauses, flashes four times, etc.: this indicates level 4.

NOTE: One sec ond af ter you stop trans mit ting levels 2, 3 or 4 (chan nels 5–16), the re mote con trol auto mati cally re turns to level 1 (chan nels 1–4).

Con cept 600/199

9

Remote Control Operation (Continued)

Remote Control Channel Assignments

Chan nel #

1

2*

3

4

5*

6*

7*

8*

Func tion

Arm/Disarm

Activate Auxilliary Output A

(usually remote trunk release)*

Silent Arm/Disarm

IntelliStart 4 Activation

Headlight Activation*

SmartWindows 4 Accessory*

Activate Auxilliary Output B*

Activate Auxilliary Output C*

Chan nel #

9

10

11*

12*

13*

14*

15

16

Func tion

Remote Valet

Proximity Sensor Override

Manual Transmission enable/AutoStart

(IS4 required)

Unassigned*

Unassigned*

Unassigned*

Adjust Sensitivity of Optional OmniSensor

Adjust Sensitivity of Proximity Sensor

* These channels can be assigned to control other Clifford ACG 2 systems and accessories on multiple vehicles.

Companion Remote Control Operation

Press but ton number(s)

Func tion

Arm/Disarm

Activate Auxilliary Output A*

(usually remote trunk release)*

Silent Arm/Disarm

Timed headlight activation

IntelliStart 4 Accessory*

SmartWindows 4 Accessory*

Remote Valet Mode Enter/Exit*

Activate Auxilliary Output B

Activate Auxilliary OutputC

Remote Proximity Sensor Override

+ ✱

+

+ ✱

+ ✱

+

+

*These channels/buttons can be assigned to control other Clifford systems that use ACG 2 technology and accessories on other vehicles.

10

Con cept 600/199

Sensor Adjustment

Digital Dual-Zone Proximity Sensor 4

The Concept 600 is equipped with our unique Digital Dual-Zone Proximity Sensor that uses digital signal processing to detect movement inside the passenger compartment and very near the vehicle. If a thief were to break a window and either enter or lean into the passenger compartment, the primary zone of this sensor would trigger the full alarm. However, if a thief brought his hands and face to the window a warning tone would sound.

Be aware that the Proximity Sensor uses radar waves to detect movement. These waves pass through nonmetallic materials like plastic, carpet, glass and wood. However, metal and metallic-coloured paint, metallic-coloured plastic and even some metallic window tinting materials will interfere with or completely block the radar waves. As such, it is not unusual that the Proximity Sensor zones require some adjustment after installation. In some instances, you may need to try a different location for the sensor.

Since any metal ob jects above or near the Prox im ity Sen sor will have a sig nifi cant im pact on op era tion, warn your customer never to place coins, CDs, cas settes (due to the iron ox ide tape) or other me tal lic ob jects above or near where the sen sor is mounted.

1. Turn off any fluorescent lights that may interfere with the sensitivity testing of the Concept 600’s radar sensor.

2. Disarm the system with the remote control.

3. Transmit channel 16 on the master remote (LevelShift three times, then button 4). You will hear one chirp and the LED will turn on.

4. Test the Proximity Sensor’s primary zone by rapidly leaning through an open window into the passenger compartment. You will hear a siren chirp when the primary zone is triggered. This should not occur near the window, but instead when you would be in a position to touch the car stereo.

To change the sensitivity of the primary zone, press and release button 2 to increase sensitivity or button 4 to decrease sensitivity.

To rapidly increase or decrease several steps, press and hold the button. For each sensitivity increase, you will hear a higher and higher pitched confirmation chirp. For each sensitivity decrease, you will hear a lower and lower pitched confirmation chirp. Two

LoudChirps indicate minimum and maximum settings of the 32-step range of settings. You may now press button 3 to adjust the warning zone, or press button 1 to fully exit the Proximity Sensor adjustment mode (you will hear 3 chirps).

To change the sensitivity of the warning zone, press button 3 (you’ll hear 1 chirp). Then use the same procedure as above, but this time, rapidly bring your hands and face to the window as a thief would to see what’s inside. The sensitivity of the warning zone should be set so that it is triggered when your face and hands are within a few inches of the window, no further. When done, press

button 1 to reselect the primary zone (you will hear 2 chirps), then button 1 again to fully exit Proximity Sensor adjustment mode

(you will hear 3 chirps).

5. Repeat the preceding steps as required. An improperly adjusted sensor will cause the Concept 600 to false alarm or not respond properly to a genuine threat. Keep in mind that you may need to reposition the sensor, possibly after the customer has had the system for several days.

Re mote-Con trolled Over ride of Each Prox im ity Sen sor Zone

Transmitting channel 10 whenever the system is armed will override the warning zone of the Proximity Sensor. This prevents the system from sounding warnings if the vehicle must be parked in an area with heavy pedestrian traffic. A second transmission of channel 10 anytime afterward whilst the system is still armed will override both zones of the Proximity Sensor. This comes in handy when a pet or a passenger must be left in the vehicle. The channel 10 warning zone override is visually confirmed with 4 flashes of the parking lights. A second channel 10 transmission to override both zones is confirmed with four more flashes. The sensor zones are automatically restored the next time you arm.

FACT—False Alarm Control and Test

The system microprocessor automatically checks for another activated sensor or trigger before sounding the siren a second time, thus preventing any further false alarms. If you wish to test FACT, simply:

1. Arm the Concept 600 with the re mote con trol.

2. Wait 10 seconds after the interior light turns off, then trigger the Proximity Sensor to activate the siren.

3. Do not disarm the system, let the siren complete its cycle.

4. Attempt to trigger the sensor again. The alarm should be silent.

5. Unlock and open a door. The alarm should sound immediately. You may now disarm.

Con cept 600/199

11

Eight-Event TotalRecall

The system’s nonvolatile memory records the identity of the last eight activated or malfunctioning triggers and sensors:

NOTE: The CliffNet Wizard Pro dis plays the Eight- Event To tal Re call data in a graphi cal for mat.

1. With the ignition OFF, press and hold the unmarked side of the PlainView 2 Switch.

2. Use the remote control to arm, and then again to disarm, and then release the button.

3. The LED will flash 1–10 times, pause, then flash 1–10 times, etc. Write down the number of flashes in each cycle.

4. Refer to the following chart. The first number you wrote down was the most recently activated trigger or sensor. The next number is the second most recent, and so on up to as many as the last eight activations.

Num ber of LED flashes be tween pauses

1 flash

2 flashes

3 flashes

4 flashes

5 flashes

6 flashes

7 flashes

8 flashes

9 flashes

10 flashes

Trig ger/sen sor in di ca tion

Digital Dual-Zone Proximity Sensor

Dual-Zone OmniSensor

Digital Tilt/Motion Sensor

Door Trigger

0 Trunk Trigger

Hood Trigger

An attempt was made to turn on the ignition or start the engine whilst the system was armed

More than three consecutive incorrect valet codes were entered whilst the system was in BlackJax mode

BlackJax Activation

System Power Interruption

5. If a sensor is often activated, decrease that sensor’s sensitivity (or reposition the sensor, if necessary). If a certain trigger is often activated, check pin switch operation, verify that the pin switch is not exposed to moisture and check the trigger wire for possible shorting.

12

Con cept 600/199

Programmable Features

Concept 600 comes from the factory with its features preprogrammed as noted in bold text in the tables on pages 15 and 16. Some features can be programmed by the installer or the user, others can only be programmed only by the installer. There are two tables provided which define the user-programmable and installer-programmable features.

Using the CliffNet Wizard Pro

The CliffNet Wizard Provides intuitive access to all installer and user-programmable features through a user-friendly, graphical user interface. Because CliffNet Wizard Pro is Windows™-compatible, most operations can be accomplished by simply pointing and clicking a mouse. CliffNet Wizard Pro totally eliminates complicated programming charts and lengthy programming sequences.

Please refer to the CliffNet Wizard Pro User’s Guide for more programming information if you are using the CliffNet Wizard Pro.

Otherwise, for manual programming refer to the tables provided in the following sections.

Programming the User-Selectable Features

1. Write down the column (across) number and row (down) number of the feature(s) you wish to program.

2. Turn the ignition to the “ON” position or start the engine.

3. Enter the factory preset valet/programming code of “2” by pressing the PlainView 2 Switch’s ✱ button twice, then press the unmarked button.

4. After entering the code, press and hold the ✱ for about 3 seconds until you hear one siren chirp and the LED turns on to acknowledge program mode entry. The Concept 600 is now in the “Feature Select” position for User-Programmable Features.

5. Select the feature column: Press the unmarked button the same number of times as the column number. Pause. You will then hear the same number of chirps as the column number you have selected, audibly confirming your selection.

6. Within five seconds, select the feature row: Press ✱ button the same number of times as the feature’s row number. You’ll hear a chirp each time you press the unmarked side to help you count.

7. If there is a NOTE for the selected feature, perform the actions noted.

8. Pause. You will hear either one or two chirps: two chirps = ON, one chirp = OFF.

9. You can select another feature, or you can exit program mode: a. To select another feature in that same column, repeat step 6 within the next five seconds (after five seconds, three chirps indicate that the Concept 600 is now back in the Feature Select position).

b. To select a different feature column, repeat step 5.

c. To exit program mode, turn the ignition off (you’ll hear three chirps and the LED will turn off to indicate exit of program mode), or wait 60 seconds and the Concept 600 will automatically exit program mode.

It may sound a little complicated, but it really isn’t. Briefly, here is all you do: choose the feature you want to change, enter program mode, select that feature’s column and row, wait for the on/off chirp confirmation, then turn off the ignition. That’s it!

Con cept 600/199

13

User-Programmable Features

User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON)

Fea ture

Select

Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4

1

2

AutoProgram New Master

Remote

NOTE 1

Personalized Siren Sounds*

NOTE 2

Play Siren Sounds*

Chirps

(Off/LoudChirps/QuietChirps)

(1 chirp/2 chirps/3 chirps)

NOT USED

Remote Valet Feature

(Off/On)

AutoArming

(Off/On)

AutoArm & Lock

(Off/On)

En try De lay

(Off/On)

Arm/Disarm with

Secondary Remote

NOTE 6

Trunk Release with

Secondary Remote

NOTE 7

Silent Arm/Disarm with

Secondary Remote

NOTE 7

Siren Duration

(30/60/90 Seconds)

(1 chirp/2 chirps/3 chirps)

AutoStart**

(Neither/Battery/Temperature/Both)

(1 chirp/2 chirps/3 chirps/4 chirps)

FACT

(Off/On)

Timed Headlight Activation with Secondary Remote

NOTE 7

AutoLock

(Off/Instant/RPM-Dependent)

(1 chirp/2 chirps/3 chirps)

AutoUnlock

(Off/On)

BlackJax

(Off/On)

Clear All Remotes

NOTE 4

Headlight Duration

10 Seconds

NOTE 5

NightVision

(Off/On/On without post-parking illumination)

Remote Start** with

Secondary Remote

NOTE 7

Window Rolldown/Venting

with Secondary Remote

NOTE 7

Re set All to Fac tory Set tings

(ex cept re mote controls and valet code)

NOTE 3

Valet Code

SHOULD ONLY BE

PROGRAMMED BY THE VEHICLE

OWNER

Night Vi sion Ac ti va tion

(Lighter /Twi light/Darker)

Remote Valet Mode

with Secondary Remote

NOTE 7

*Requires Self-Powered SmartSiren 4

*

*Requires optional Intellistart 4

n

NOTE 1:

Press button 1 on the 16-channel master remote, you will hear one chirp. Press button 1 again, you will hear two chirps.

n

NOTE 2:

When this feature is selected, siren sound 1 will play for five seconds. Press marked to turn the siren sound off, press unmarked to activate the sound. Next, siren sound 2 will play for five seconds. Press marked to turn the siren sound off, unmarked to activate it. The system will cycle through all six siren sounds.

n

NOTE 3:

You will hear two chirps when all features are reset.

n

NOTE 4:

When you hear two chirps, all remote controls will have been erased from the system memory. You must now add the new and/or existing remote controls to the system (i.e., AutoProgram each remote that will be used with the Concept

600).

n

NOTE 5:

Once this feature is selected, one chirp is provided to indicate that the timer has started. You can set this anywhere from one second to four minutes. When the desired duration has been reached, press the unmarked side of the

PlainView 2 switch. The system responds with two chirps to confirm the new system timer duration.

n

NOTE 6:

Programs a 4-channel secondary, 16-channel master, or any other remote control from another IntelliGuard system to arm or disarm the vehicle. For instance, to set button 13 of the other car’s master remote control to arm/disarm the system, select column 4, row 1, then transmit channel 13 from the remote you are programming. The system will respond with one chirp. Immediately transmit channel 13 again. The system will respond with two chirps. Button 13 of the other vehicle’s remote will now arm/disarm the system.

n

NOTE 7:

This feature can be programmed onto the remote control of another IntelliGuard system, after that remote has been programmed to arm/disarm this system. Select the row and column number, then transmit the unused button on the other remote that you want to use to perform that function. The Concept 600 will respond with the same number of chirps as the row number. Please note that you must first set a button on the remote that will arm/disarm the system (column 4, row 1) before these others will be accepted.

14

Con cept 600/199

Installer-Programmable Features

To access the installer-programmable features, use the procedure defined in the User-Programmable section, but in step 4, hold and press the ✱ side of the PlainView 2 Switch for 10 seconds. You will hear three confirmation chirps indicating that the system is in installer-program mode.

Table of Installer-Programmable Features (1 chirp = OFF, 2 chirps = ON)

Fea ture

Select

Unmarked 1 Unmarked 2 Unmarked 3

1

2

4

5

6

Single/Double Lock Pulse

(1 chirp/2 chirps)

Single/Double Unlock Pulse

(1 chirp/2 chirps)

Lock/Unlock Pulse

3 second/1 second

(1 chirp/2 chirps)

AutoActivate Auxilliary Output C upon Remote Arming

(On/Off)

Program RPM

See

Mandatory RPM Programming

Aux il iary Si ren Out put

(Constant/Pulsed)

(1 chirp/2 chirps)

Auxilliary Output Timer

Duration

(10 seconds)

See NOTE 1

Auxilliary Output A Type

(Pulsed/Timed/Latched)

(1 chirp/2 chirps/3 chirps)

Auxilliary Output B Type

(Pulsed/Timed/Latched)

(1 chirp/2 chirps/3 chirps)

Auxilliary Output C Type

(Pulsed/Timed/Latched)

(1 chirp/2 chirps/3 chirps)

Diesel Engine/Petrol Engine

(1 chirp/2 chirps)

(For IntelliStart 4 only)*

Learn PageMate 4 ID

Door Ajar Warning/Delayed

Courtesy Lights

(1 chirp/2 chirps)

Auxilliary Output A Interlock

(On/Off)

Auxilliary Output B Interlock

(On/Off)

Auxilliary Output C Interlock

(On/Off)

Program Window RollUp or

SmartWindows 4

See NOTE 2

NOT USED

* Must program RPM’s AFTER changing this feature n

NOTE 1:

Once this feature is selected, one chirp is provided to indicate that the timer has started. You can set this anywhere from one second to 4 minutes. When the desired duration has been reached, press the unmarked side of the PlainView 2 switch. The system responds with two chirps to confirm the new system timer duration.

n

NOTE 2:

To program the Window RollUp feature, first roll down the windows using the switches located inside the vehicle.

Next, access column 3, row 5. The system responds with one chirp and then rolls the windows up automatically. Wait 10 seconds, the system will provide a two-chirp confirmation and the programming is complete.

System Checklist & Troubleshooting

The fol low ing check list and trou ble shoot ing tips will as sure that you have in stalled the Concept 600 cor rectly. If the sys tem does not re act as noted, fol low the trou ble shoot ing tip(s) de noted with a black box be low that item, then re peat the step. Each suc ces sive step re quires that the pre vious step has been com pleted as in di cated.

The Clifford Wizard simplifies the troubleshooting process by providing system diagnostic information in a graphical format. All system settings are provided at-a-glance, and adjustments to the system settings can be made with a click of a mouse. This reduces the amount of time required for performing the following tests.

Step 1.

Re- enable the cour tesy lights.

In step 1 of the Important Information sec tion in this binder, the in te rior cour tesy lights were disabled. You must now re-enable the courtesy lights by re placing the fuse you re moved or re set the cour tesy light switch back to its nor mal “DOOR” po si tion bef ore pro ceed ing.

Con cept 600/199

15

System Checklist & Troubleshooting (Continued)

Step 2.

Test the Im mo bi li za tion cir cuits.

n

Arm the Concept 600 (either from inside or outside the vehicle) and wait 10 seconds. Turn the ignition to the “ON” position. o o o

Engine does not respond. This is the correct response, proceed to the ImmoBilization test.

Engine starts or cranks. The starter/ig ni tion/fuel pump or immobilization cir cuits have been mis wired. Care fully re test the ve hi cle wires as noted in the Starter and Ig ni tion Immobiliza tion Cir cuits section on page 7. Be sure the ignition input/output is correct!

Engine still starts or cranks after retesting all the wiring as noted on page 7, check the power and ground connections.

Then make sure the fuses are in the fuseholders, verify the control unit connectors are securely fastened, verify the ignition input and output wires are connected to the true ignition line instead of a 12V or accessory line, and verify that the transmitters are programmed correctly.

Step 3.

Test the chirps.

Close all doors and arm the Concept 600 by pressing button 1 on the remote control. n

2 Chirps: This is the correct response. Proceed to step 4.

n

4 Chirps: If you hear 4 chirps ei ther im me di ate ly or 5-10 sec onds af ter the ini tial two chirps, a trig ger or sen sor is open or

active, or the ve hi cle has de layed cour tesy lights and the De layed Cour tesy Lights fea ture has not been programmed on. Dis arm with the re mote con trol, en ter the ve hi cle and turn on the ig ni tion. The LED will flash 1–10 times, pause, then re peat the same number of flashes (the flash cy cle re peats five times for your con ven ience). Ref er to the following chart.

Num ber of LED flashes be tween pauses

1 flash

2 flashes

3 flashes

4 flashes*

5 flashes

6 flashes

7 flashes

8 flashes

9 flashes

10 flashes

Trig ger/sen sor in di ca tion

Digital Dual-Zone Proximity Sensor 4 4

Dual-Zone OmniSensor

Digital Tilt/Motion Sensor

Door Trigger*

Trunk Trigger

Hood Trigger

An attempt was made to turn the ignition “ON” or start the engine whilst the system was armed

More than three consecutive incorrect valet codes were entered whilst the system was in BlackJax mode

BlackJax Activation

Power Interruption

*

If the de layed cour tesy lights fea ture is ac ti vated, this trig ger/sen sor in di ca tion will not be pro vided.

16

Con cept 600/199

System Checklist & Troubleshooting (Continued)

o o o

If the Prox im ity Sen sor is in di cated, check the mount ing lo ca tion and sen si tiv ity set ting as noted in the Sensor Adjustment section on page 12. If one of the trig ger points is in di cated, check pin switch op era tion and check for shorts in the trig ger line.

If the tilt sensor is indicated, check the mounting location and, if necessary, cut the small black wireloop (see diagram on page 3) to enable the two-minute arming delay.

If the door trig ger is in di cated, ac ti vate the de layed cour tesy lights fea ture.

n No chirps. If there are no chirps, ver ify that the Chirps fea ture (col umn 2, row 1) is “On” and check the wir ing con nec tions as noted in the Self-Powered SmartSiren 4 sec tion on page 8. n

Silent Night “OFF” n

Self-Powered SmartSiren 4 battery is charged.

NOTE: If none of the troubleshooting techniques described in steps 3 - 7 corrects the problem, perform the following diagnostics:

o o o o o

Make sure the fuses are in the fuse hold ers.

Check the power and ground con nec tions.

Ver ify that the con trol unit con nec tors are prop erly in serted into the con trol unit.

Verify that the ig ni tion in put and out put wires are con nected to the true ig ni tion line instead of a 12V line. Find the true ig ni tion line by fol low ing steps 1-4 of the Starter and Ig ni tion ImmoBiliza tion Cir cuits sec tion on page 7.

Ver ify that the trans mit ters are pro grammed cor rectly.

NOTE: If the 20- amp fuse blows upon arm ing:

o o

Disconnect the Concept 600’s two parking light wires, replace the 20-amp fuse and rearm. If the fuse does not blow, one (or both) of the ve hi cle’s parking light wires is short ing. Find and cor rect the short(s), re con nect the parking light wires, then re arm.

If the fuse blows whilst the parking light wires are dis con nected, the door locks are not wired cor rectly. Re con nect the ve hi cle’s power lock ing sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door Lock s sec tion of this binder and wire the locks as in di cated, then re place the 20- amp fuse.

Step 4.

Test the park ing lights.

Arm the sys tem by press ing but ton 1 on the re mote con trol.

n

Two flashes. This is the correct response, proceed to step 5.

n

One flash. If the parking lights flash only once, the Concept 600 had pre vi ously AutoArmed it self pas sively and by press ing but ton 1 the sys tem dis armed (re mote dis arm ing is ac knowl edged with one parking light flash). Re peat step 1.

n No flashes. If no flashes, ver ify the parking light bulbs are op era tional. If not, they must be re placed. If so, re peat steps 1-5 of the Parking lights sec tion in this binder.

n

Only one side flashes. If only the right or the left side parking lights flash, see the Parking Lights sec tion in this binder.

Step 5.

Test the power win dows.

Arm the system by pressing button 1 on the remote control.

n

Power windows close. This is the correct response, proceed to step 6.

n

Power windows do not close. If the power windows do not close, disarm and rearm the system (the one-time Window RollUp

Bypass feature may have been activated—arming and rearming will deactivate it). Make sure the Window RollUp feature has been programmed using the chart on page 16. If the windows still do not roll up upon arming, refer to the Window RollUp section of this binder to insure that the Window RollUP wiring has been interfaced correctly.

WARN ING: If the doors do not close, DO NOT ac ti vate the ve hi cle’s window switches. If the windows have been mis wired, do ing so may dam age the Concept 600 con trol unit, the ve hi cle’s elec tri cal sys tem and/or the power window mo tors.

Con cept 600/199

17

System Checklist & Troubleshooting (Continued)

Step 6.

Test the door locks.

Arm the sys tem by press ing but ton 1 on the re mote con trol.

n Doors lock. This is the correct response, proceed to step 7.

n

Doors do not lock. You ei ther se lected the wrong door lock dia gram or con nected the wires in cor rectly. Re con nect the ve hi cle’s power lock ing sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door Locks sec tion of this binder and wire the locks as in di cated.

WARN ING: If the doors do not lock, DO NOT ac ti vate the ve hi cle’s lock switches. If the locks have been mis wired, do ing so may dam age the Concept 600 con trol unit, the ve hi cle’s elec tri cal sys tem and/or the power lock servo mo tors.

n

Doors unlock. You ei ther se lected the wrong door lock dia gram or con nected the wires in cor rectly. Re con nect the ve hi cle’s power lock ing sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door Locks sec tion of this binder and wire the locks as in di cated.

n Only one door locks. You ei ther se lected the wrong door lock dia gram or con nected the wires in cor rectly. Re con nect the ve hi cle’s power lock ing sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door Locks sec tion of this binder and wire the locks as in di cated.

Step 7.

Test the LED.

Arm the system by pressing button 1 on the remote control.

n Flashes repeatedly. This is the correct response, proceed to step 8.

n

No flashes. If the LED does not flash, ver ify that the LEDs VIO LET and BLACK wires are sol idly con nected to the same colour wires on the Concept 600’s wire loom. Warn ing: This is a 2- volt LED, test ing with 12 volts will de stroy the LED.

Step 8.

Test the Valet Switch

.

n Test the valet code and switch operation. Use the instructions provided on page 14 to enter programming mode. If the system enters programming mode, the switch and valet code are in operating order. If not, perform the following tests: n

Test the WHITE/BROWN wire, ignition input and verify it has +12V when the ignition is turned ON and +0V when the ignition if OFF. If not refer to Starter and Ignition ImmoBilization Circuits on page 7.

n Test the WHITE wire at the control unit connector. It should rest at 5 volts. When pressing the marked side, it should read 3 volts and when pressing the unmarked side it should read 0 volts. If any reading is incorrect, move the voltmeter to the BLACK wire at the valet switch. It should read 0 volts at rest, 0 volts when the marked side marked is pressed, and 0 volts when the unmarked side is pressed. If the BLACK wire tests correctly and the WHITE wire does not, replace the switch. If the BLACK wire tests incorrectly, repair the ground circuit. If both wires test correctly, then the valet code has been changed. Use the

CliffNet Wizard to reset the valet code.

Step 9.

Test the dis arm func tion.

n

Disarm by pressing remote control button 1. The following should occur: o o o o o o

Siren chirps once. If the siren does not chirp once, refer to step 3.

Parking lights flash once. If the parking lights do not flash once, refer to step 4.

LED stops flashing. If not refer to step 7.

Doors un lock. If not refer to step 6.

Immobilizer cir cuits im me di ate ly disen gage (test this by turn ing the key in the ig ni tion switch; the en gine should crank, start and idle nor mally). If the Immobilizer circuits do not disengage, refer to step 2.

In te rior cour tesy light(s) turn on and stay on for 30 sec onds or un til the ig ni tion is turned on, which ever oc curs first.

o

If the in te rior light(s) do not turn on, ver ify that you re placed the interior light fuse you re moved or have turned the o o lights back on as noted in step 1 of this sec tion.

Check the Concept 600’s 10- amp fuse. If the fuse blew when you dis armed, the ve hi cle uses a posi tive door trig ger and you con nected the in te rior light sup ply wire to ground in stead of +12 volts. Re place the 10-amp fuse and retest.

Check the door trig ger cir cuit. See step 10 for more information on testing the door trigger circuit.

18

Con cept 600/199

System Checklist & Troubleshooting (Continued)

Step 10.

Test the door trig ger cir cuit.

Rearm the sys tem. Wait at least 10 seconds (if the vehicle has delayed or dimming courtesy lights, be sure to wait until the interior lights have turned off). Use the key to unlock and open the driver’s door. n

Siren sounds, parking lights flash repeatedly. This is the correct response, proceed to step 11. (You can silence the siren by press ing the button on the re mote con trol once or disarm by pressing the button twice.) n

Siren does not sound immediately. If the alarm does not sound im me di ate ly when one of the doors is opened, make sure that that door’s pin switch is work ing prop erly and, when open, is con sis tently show ing less than 1.5 volts if the ve hi cle has negative- switching door trig gers or more than +11 volts if the ve hi cle has positive- switching door trig gers, also make sure the pin switch is connected to the correct wire. If not, then the door pin switch (or pin switches) is ei ther de fec tive or in need of clean ing.

Step 11.

Test the trunk trig ger cir cuit.

Arm the system, then use the key to unlock the trunk. n Si ren sounds im me di ate ly, parking lights flash re peat edly. This is the correct response, proceed to step 12. (You can silence the siren by press ing but ton 1 on the re mote con trol or disarm by pressing button 1 two times.) n

Alarm does not sound immediately. If the alarm does not sound im me di ate ly, make sure that the trunk pin switch is work ing prop erly and, when open, is con sis tently show ing less than 1.5 volts. Also make sure the trunk pin switch is connected to the correct wire. If not, the trunk pin switch must be thor oughly cleaned or re placed.

Step 12.

Test the hood trig ger circuit.

Arm the system, then open the hood. The following should occur: n

Si ren sounds im me di ate ly, parking lights flash re peat edly. This is the correct response, proceed to step 13. (You can silence the siren by press ing but ton 1 on the re mote con trol or disarm by pressing button 1 two times.) n

Alarm does not sound immediately. If the alarm does not sound im me di ate ly, make sure that the hood pin switch is work ing prop erly and, when open, is con sis tently show ing less than 1.5 volts. If not, the hood pin switch must be thor oughly cleaned or re placed.

Step 13.

Test the AutoArming fea ture.

Turn the ignition “ON” and let the car idle for 10 seconds. Turn the ignition “OFF,” then open and close the door. Wait five seconds.

n

Parking lights flash twice. 25 seconds later, the vehicle is passively armed indicated by a rapidly flashing LED. This is the correct response, proceed to step 14.

n

System does not passively arm.

o o

Make sure that Instant AutoArming has been programmed using the instructions on page 16.

Verify the door trigger connection (see step 9).

Step 14.

Test the AutoArming By pass and Win dow Rol lUp By pass fea tures.

Disarm the system. Roll the windows down and turn the ignition to the “ON” position, then immediately turn the ignition “OFF.” n

One Chirp. This is the correct response, wait 30 seconds to insure the system does not passively arm. Arm the vehicle, the windows should not close. If the windows do close, then repeat the procedure of turning the ignition “ON,” then “OFF,” and waiting for the confirmation chirp.

Step 15.

Test remote control range.

Stand approximately 50 metres from the vehicle and use the remote control to arm and disarm the system.

n The Concept 600 will re spond with the pre vi ously noted in di ca tions for arm ing and dis arm ing. If not: o o o

Re po si tion the external receiver as high as possible high up un der the dash, or as high as possible in the windshield pillar and as far as pos si ble from heavy wire looms and metal. Rotate the external receiver 90 degrees and re-test.

Make sure that the re mote con trol bat tery meas ures at least 11 volts whilst trans mit ting.

Make sure that the volt age at the con trol unit be tween the 5- amp fused power line and each of the two ground lines meas ures at least 12.0 volts (if less, make sure both chas sis grounds are solid; if the grounds are solid, the ve hi cle battery may need charg ing, serv ic ing or re place ment).

Step 16.

Test the Black Jax anti- carjacking fea ture.

Refer to the System Check section in the BlackJax section of this binder.

Con cept 600/199

19

System Checklist & Troubleshooting (Continued)

Step 17.

Test the Dual- Zone Om niSen sor.

n

Arm the system and tap the car softly with your fist. The following should occur:

Warning buzzer sounds. Proceed to the next test.

o n Hit the car firmly with your fist. The follwoing should occur: o

Alarm triggers. Proceed to step 18.

If either of these test fail, adjust the sensor using the remote control.

Step 18.

Test the Night Vi sion fea ture.

Test 1: Start the car and cover the light sen sor with your hand or an ob ject that blocks the light from the sen sor for 20 sec onds..

n

Headlights* turn on. This is the correct response. Proceed to the next NightVision test (Test 2).

n

Headlights* do not turn on. o o o o

Check the connections to the light sensor.

Verify that the alarm detects ignition properly.

Check the headlight output wire for proper output.

Check the headlight input wire for proper input.

Test 2: The en gine should still be run ning, and the head lights should still be turned on (Test 1). Shine a light into the light sen sor.

n

Headlights* turn off. This is the correct response. Proceed to step 19.

n

Headlights* do not turn off.

o o o o

Check the connections to the light sensor.

Verify that the alarm detects ignition properly.

Check the headlight output wire for proper output.

Check the headlight input wire for proper input.

*Head lights also re fers to dash board lights and run ning lights.

Step 19.

Com plete and pro vide all necessary paperwork including:

n

User’s Manual must be given to the customer.

n

Adhere the Clifford window decals to the vehicle’s windows.

Step 20.

Dem on strate Ba sic Sys tem Operation

n Remote Operations: o o o o o o

Arming/disarming and locking/unlocking

Panic Feature

Headlight Operation

Proximity Sensor Override

Valet Mode Activation/Deactivation

Accessory Activation

Sensor Adjustment o n

Window RollUp and Window RollUp Bypass n

AutoArming and AutoArming Bypass n ImmoBilization n

Valet code entry n

User-programming mode

20

Con cept 600/199

advertisement

Related manuals

Download PDF

advertisement