TKH Security Solutions XSNet S4104 SW 4 + 2-Port Fast Ethernet switch Quick Start Guide

Add to My manuals
2 Pages

advertisement

TKH Security Solutions XSNet S4104 SW 4 + 2-Port Fast Ethernet switch Quick Start Guide | Manualzz

Note that XSNet Series manuals may cover multiple models. To establish if a particular feature or specification in this manual applies to the unit at hand, consult the datasheet of the given model.

XSNet S4104SW/S4108SW

Quick Start Guide

Note: The EU Declaration of Conformity for this product can be found at www.siqura.com/support-files.

This quick start guide describes how to install and use the Industrial Managed Ethernet Switch. This is the switch of choice for harsh environments constrained by space.

Functional Description

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.

 Manageable via SNMP, Web-based, Telnet, and RS-232 console port.

 Supports Command Line Interface in RS-232 console.

 Supports 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation: 10/100/1000Mbps,

Physical Description

The Port Status LEDs and Power Inputs

full/half-duplex. Auto MDI/MDIX.

 The S4104SW is equipped with 2x 100Base-FX SFP slots.

 The S4108SW is equipped with 2x 1000Base-FX SFP slots.

 1000Base-SX/LX: Multi mode or Single mode SC type. 1000Base-BX: WDM Single mode SC type.

 Support 8192 MAC addresses. Provides 2M bits memory buffer.

 Alarms for power and port link failure by relay output.

 Power Supply: Redundant DC Terminal Block power inputs or 12VDC DC JACK with 100-240VAC external power supply.

 Operating voltage and Max. current consumption: 0.92A @ 12VDC, 0.46A @ 24VDC, 0.23A @

48VDC. Power consumption: 11W Max.

 -10°C to 60°C (14°F to 140°F) operating temperature range. Tested for functional operation @

-20°C to 70°C (-4°F to 158°F).

 Supports Din-Rail or Panel Mounting installation.

10/100Base-TX, 100Base SFP

LINK/ACT

Steady

Flashing

A valid network connection established.

Transmitting or receiving data.

ACT stands for ACTIVITY.

1000Base SFP

LINK/ACT

Steady

Flashing

A valid network connection established.

Transmitting or receiving data.

ACT stands for ACTIVITY.

Power Input Assignment

Power3 12VDC DC

Power2

Power1

+ 12-48VDC

- Power Ground

+ 12-48VDC

- Power Ground

Terminal Block

Earth Ground

Relay Output Rating 1A @ 24VDC

Relay Alarm Assignment

FAULT

*Warning signal disable for following:

1. The relay contact closes if Power1 and

Power2 are both failed but Power3 on.

2. The relay contact closes if Power3 is failed but Power1 and Power2 are both on.

Console Configuration

 Connect to the switch console:

Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of the terminal or computer running the terminal emulation application. Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal) to the switch console port.

 Configuration settings of the terminal-emulation program:

Baud rate: 115,200bps

Data bits: 8

Parity: none

Stop bit: 1

Flow control: none

 Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:

 Logon to Exec Mode (View Mode):

At the “switch_a login: prompt just type in “root” and press <Enter> to logon to Exec Mode (or View

Mode). And the “switch_a>” prompt will show on the screen.

DC Terminal Block Power Inputs: There are three power inputs can be used to power up this switch.

Redundant power supplies function is supported.

1 V2

XSNet S4104SW/S4108SW

Web Configuration

 Login the switch:

Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be shown as below:

 Logon to Privileged Exec Mode (Enable Mode):

At the “switch_a>” prompt just type in “enable” and press <Enter> to logon to Privileged Exec Mode (or

Enable Mode). And the “switch_a#” prompt will show on the screen.

 Logon to Configure Mode (Configure Terminal Mode):

At the “switch_a#” prompt just type in “configure terminal” and press <Enter> to logon to Configure

Mode (or Configure Terminal Mode). And the “switch_a(config)#” prompt will show on the screen.

 Set new IP address and subnet mask for Switch:

At the “switch_a(config)#” prompt just type in “interface vlan1.1” and press <Enter> to logon to vlan 1

(vlan1.1 means vlan 1). And the “switch_a(config-if)#” prompt will show on the screen.

Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies IP address. “M” specifies IP subnet mask. “M”= 8: 255.0.0.0, 16:255.255.0.0, or 24: 255.255.255.0.

For example, At the “switch_a(config-if)#” prompt just type in “ip address 192.168.1.10/24” and press

<Enter> to set new IP address (192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch.

 Enter the factory default login ID: root.

Enter the factory default password (no password).

Then click on the “Login” button to log on to the switch.

2 V2

advertisement

Related manuals

Download PDF

advertisement