Quareo Q3000 Network Chassis Installation

Add to My manuals
12 Pages

advertisement

Quareo Q3000 Network Chassis Installation | Manualzz

Quareo

Q3000

Network Chassis

Installation Instructions

ADCP-92-319

Issue 1 5/2011

24458-A

Content Page

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 UNPACKING AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 CHASSIS INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1

Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.2

Grounding Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.3

Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.4

Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.4.1

LC or MPO Trunk Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.4.2

LC Array Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4.3

LC 900 micron Fiber Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 CUSTOMER INFORMATION AND ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

INTRODUCTION

The Q3000 Network Chassis is available in a 2-blade 1RU, 4-blade 2RU, or 8-blade 4RU configuration.

300001724507 Rev A Page 1

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

Trademark Information

TE Connectivity (logo), TE (logo), Tyco Electronics, ADC, TrueNet, and Quareo are trademarks.

Admonishments

Important safety admonishments are used throughout this manual to warn of possible hazards to persons or equipment. An admonishment identifies a possible hazard and then explains what may happen if the hazard is not avoided. The admonishments — in the form of Dangers,

Warnings, and Cautions — must be followed at all times. These warnings are flagged by use of the triangular alert icon (seen below), and are listed in descending order of severity of injury or damage and likelihood of occurrence.

Danger: Danger is used to indicate the presence of a hazard that will cause severe personal

injury, death, or substantial property damage if the hazard is not avoided.

Warning: Warning is used to indicate the presence of a hazard that can cause severe personal

injury, death, or substantial property damage if the hazard is not avoided.

Caution: Caution is used to indicate the presence of a hazard that will or can cause minor

personal injury or property damage if the hazard is not avoided.

General Safety Precautions

Warning: To prevent electrical shock, never install chassis in a wet location or during a

lightning storm. When installing or modifying telephone lines, disconnect lines at the network interface before working with uninsulated lines or terminals.

Caution: When mounting equipment in the rack make sure mechanical loading is even to avoid

a hazardous condition, such as loading heavy equipment in the rack unevenly. The rack should safely support the combined weight of all equipment it supports.

Caution: Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Caution: This equipment is to be installed only in Restricted Access Areas (dedicated

equipment rooms, equipment closets, etc.) in accordance with Articles 110-16, 110-17, and 110-

18 of the National Electrical Code, ANSI/NFPA 70.

Page 2

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

1 SPECIFICATIONS

Specifications for the chassis are listed in

Table 1

.

Table 1. Network Chassis Specifications

PARAMETER SPECIFICATION REMARKS

Environmental

Operating Conditions

+14

° F to +140° F (

10

° C to +60° C) 5% to 95% RH

Storage Conditions

No Condensation

40

° F to +158° F (

40

° C to +70° C) 10% to 95% RH

No Condensation

Mechanical

Dimensions D x W x H

13.35 in (33.9 cm) D x 19.01 in (48.29 cm) W x

1.7 in (4.32 cm) H

1RU chassis

13.35 in (33.9 cm) D

3.45 in (8.73 cm) H x 19.01 in (48.29 cm) W x

2RU chassis

4RU chassis

Weight

13.35 in (33.9 cm) D x 19.01 in (48.29 cm) W x

6.95 in (17.65 cm) H

4.1 lb. (1.86 kg.)

5.3 lb. (2.40 kg.)

6.8 lb. (3.08 kg.)

Empty 1RU chassis

Empty 2RU chassis

Empty 4RU chassis

2 UNPACKING AND INSPECTION

Unpack and inspect the various components as follows:

1. Inspect the exterior of the shipping container(s) for evidence of rough handling that may have damaged the components in the container.

2. Unpack each container while carefully checking the contents for damage and verify with the packing slip.

3. If damage is found or parts are missing, file a claim with the commercial carrier and notify

TE Customer Service. Save the damaged cartons for inspection by the carrier.

4. Refer to

Section 4 Customer Information and Assistance

if you need to contact TE.

5. Save all shipping containers for use if the equipment requires shipment at a future date.

The following procedures provide the necessary instructions for installing and wiring a chassis in an equipment rack.

3 CHASSIS INSTALLATION

Warning: To prevent electrical shock, never install chassis in a wet location or during a

lightning storm. When installing or modifying telephone lines, disconnect lines at the network interface before working with uninsulated lines or terminals.

Page 3

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

Caution: When mounting chassis in the rack make sure mechanical loading is even to avoid a

hazardous condition, such as loading heavy equipment in the rack unevenly. The rack should safely support the combined weight of all equipment it supports.

Tool and hardware requirements are listed in Table 2 .

Table 2. Installation Tools and Hardware Needs

CONSIDERATION

Tools Needed

Rack Mounting

DESCRIPTION

#1 Phillips Screwdriver,

#2 Phillips Screwdriver

3/16” Standard Screwdriver

19” EIA/WECO/ETSI Rack Mounting

Use supplied #12-24 screws and #2 Phillips Screwdriver to secure the chassis to the rack or cabinet or

Use supplied M6 screws, cage nuts and #2 Phillips Screwdriver to secure the chassis to the rack or cabinet or

Use TrueNet

®

Frame “quick fit” solution.

Grounding Secure chassis to ground. Use #1 Phillips Screwdriver to tighten the 10–32 screws through the ground lug (provided) into the chassis ground PEM nuts.

Ground cables are NOT provided with the chassis.

Incoming IFC Cable

Clamping

Use supplied cable clamps and 3/16” standard screwdriver to secure the incoming IFC cable.

3.1

Rack Installation

Caution: This equipment is to be installed only in Restricted Access Areas (dedicated

equipment rooms, equipment closets, etc.) in accordance with Articles 110-16, 110-17, and 110-

18 of the National Electrical Code, ANSI/NFPA 70.

This procedure provides instructions for installing the chassis in a 19-inch (482.6mm) equipment rack. Check the work order to determine the chassis location in the rack. Mounting hardware is shipped loose.

Each chassis is secured with either 12-24 screws, M6 hardware, or TrueNet

®

quick fit hardware depending on the rack used.

1. Obtain the following tools and equipment:

• Flat blade or Phillips screwdriver (type to match mounting screws)

• Locate mounting hardware required.

2. Determine what rack size is being used. When installing in a 19-inch rack use the hardware provided to attach the chassis to the rack.

3. Locate the equipment rack mounting space that is specified for the chassis.

4. Place chassis in the assigned mounting space and align the holes in the mounting brackets

with the holes in the equipment rack. See Figure 1

.

5. Secure chassis to equipment rack using the appropriate hardware. Torque these screws to approximately 27 pound-inches (3.1 Newton meters).

Page 4

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

LOCKWASHER

(4)

12-24 x 1/2 IN.

SCREW (4)

MOUNTING

BRACKET

RACK

FRONT

FLANGE

24459-A

Figure 1. Installing 2RU Chassis

3.2

Grounding Chassis

This procedure establishes a ground connection between the chassis and the earth ground connection. Frame ground terminations (10–32 screws) are provided on the chassis, for a frame ground connection. This connection must be made in accordance with all local and national electrical codes.

1. Locate ground location on chassis, see Figure 2 . At grounding location remove protective

tape from chassis.

2. Using AWG 14 (1.6mm) solid copper wire, secure two hole ground lug to one end of the ground wire (installer provided). Secure ground lug to chassis with two 10–32 screws.

Torque ground screws to approximately 15 pound-inches (1.7 Newton meters).

Caution: Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to ground connections.

Page 5

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

24460-A

GROUND

LOCATION

Figure 2. 2RU Chassis Ground Location

3. To assure proper operation the chassis should be connected to a good earth ground. There must be no switching or disconnecting devices in the grounding circuit conductor between the power source and the point of connection to the grounding electrode conductor.

4. Connect the other end of the ground wire to the earth ground conductor. Ensure this connection is made using methods and hardware that meets all applicable local and national electrical codes.

3.3

Blade Installation

Several single-mode or multimode blades are available for installation in the network chassis.

They are LC-to-MPO, LC-to-LC, and MPO-to-MPO. For cable clamping and management reasons mixing of fiber cable fanout types in a single chassis is not recommended. A blank cover (Catalog # QBCB-HR), one per slot is available to fill unused slots in the chassis. To aid in cable connections and routing each blade has two detents. Refer to

Figure 3

.

Page 6

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

24461-A

BLADES FULLY

INSERTED

BLADE

AT 6-INCH

DETENT

BLADE

AT 3-INCH

DETENT

Figure 3. Fiber Blade Detents

Install blades starting at the bottom, filling the remaining slots until the chassis is full.

1. Align blade edges with slot in chassis and slide into chassis from the front.

2. Blade will snap into the chassis when it is inserted about half way.

3. Press in on Red Latches on each side of the blade and push in to next detent.

4. Push in on second set of red latches and push blade all the way into the chassis.

5. When blade is pushed all the way into the chassis it is fully seated in the chassis.

6. Route incoming fibers to chassis. See Section 3.4 Cable Installation and attach cables to

appropriate adapters.

7. Make sure to route the fiber cables right or left as determined by the side of the chassis the cables are entering from. Route fiber cables through cable management system to the front of the chassis and attach to proper adapters.

8. Install blank covers in unused slots by placing the right end into the recess on the right side of the chassis, then push the left end (latch) into the left side of the slot. Remove blank cover by sliding latch to the right and lifting cover out of the chassis.

Blade removal is the reverse of installation. Make certain that all data passing through a blade is rerouted before beginning the removal process.

Page 7

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

3.4

Cable Installation

Note: Remove dust cap, inspect, and clean MPO connector per ADCP-96-150 instructions before terminating. Remove the ferrule dust cap from one of the patch cord connectors and then clean the connector as specified in the Optical Fiber Connector Wet and Dry Cleaning

Instructions (ADCP-90-159) or by locally approved procedures.

Trunk cables enter the chassis from the side near the rear. Each fiber fanout maybe secured to the rack above or below the chassis or to the fanout retainers secured to the chassis.

3.4.1

LC or MPO Trunk Cable Installation

When using trunk cables the fiber fanout is normally secured to the rack above or below the chassis. A compression fitting secures the cables at the chassis entry point. Mille-Ties are used to secure the cables to the sliding module. From the tie point, the optical fibers are routed to the adapters at the front of the blade.

Use the following procedure to install the cable:

1. Locate the cable entry location that is specified for cable installation as shown in

Figure 4

.

2. Route cables to chassis securing cables to rack per local practices.

3. Assemble grommets and cable clamps on fiber cables as shown in Figure 4

.

MILLE-TIE

8-INCH

SERVICE

LOOP

COVER

PLATE

SCREWS

CABLE

CLAMP

USE GROMMET FOR

SMALLER NUMBER

OF CABLES

Figure 4. Cable Clamp Installation (MPO Connector)

Page 8

© 2011 Tyco Electronics Corporation.

24462-A

ADCP-92-319 • Issue 1 • 5/2011

4. Adjust cables leaving an 8–inch service loop within the chassis, this allows blades to be withdrawn. Tighten compression fitting screws to secure cables at the cable entry location.

5. Cable clamps and several grommets are provided with the cable clamp kit for securing cables to the chassis. More than one grommet may be needed to secure cables in the clamp.

6. Connect cables to the back of the blade: a. Leave blade fully inserted in the chassis when connecting MPO connectors to MPO to

LC adapters.

b. Before connecting MPO connectors to MPO to MPO adapters pull blade out to the second detent.

7. Use Mille-Ties to secure cables to sliding blade. See Figure 5 .

FIBER

FANOUT MPO

CONNECTOR

MILLE-TIE

24463-A

8-INCH

SERVICE

LOOP

CABLE

CLAMPS

Figure 5. Cable Installation (MPO Connector)

3.4.2

LC Array Cable Installation

When using array cables the fiber fanout is normally secured to the chassis with retainers. Mille-

Ties are used to secure the cables to the sliding blade. From the tie point, the optical fibers are routed to the adapters at the front of the blade.

Use the following procedure to install the cable:

1. Locate the cable entry location that is specified for cable installation as shown in

Figure 6 .

Note: To prevent cable congestion install blades and related fiber fanouts starting at the bottom of the chassis working up the chassis until all slots are filled.

2. Route cables to chassis securing cables to rack per local practices.

Page 9

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

3. Adjust cables leaving an 8–inch service loop within the chassis that allows blades to be withdrawn.

4. Before connecting fibers to adapters pull blade out to the second detent.

5. Slide fiber fanout onto posts on chassis. After installing the last fiber fanout slide a fanout retainer over each post.

6. Use Mille-Ties to secure cables to sliding blade. See Figure 6 .

LC

CONNECTORS

MILLE-TIE

FANOUT

MOUNTING

POSTS FIBER

FANOUT

Figure 6. LC Array Cable Installation

8-INCH

SERVICE

LOOP

FANOUT

RETAINERS

24464-A

3.4.3

LC 900 micron Fiber Installation

When using trunk cables the fiber fanout is normally secured to the rack above or below the chassis. A compression fitting secures the cables at the chassis entry point. Mille-Ties are used to secure the cables to the sliding module. When using 900 micron cables the recommended breakout length is 26-inches (66 cm). From the tie point, the optical fibers are routed to the adapters at the front of the blade. Radius limiters are located on the blade for fiber slack storage.

Use the following procedure to install 900 micron fibers:

1. Locate the cable entry location that is specified for cable installation as shown in

Figure 7 .

Note: To prevent cable congestion install blades and related fiber fanouts starting at the bottom of the chassis working up the chassis until all slots are filled.

2. Route cables to chassis securing cables to rack per local practices.

3. Assemble grommets and cable clamps on fiber cables as shown in Figure 7

.

Page 10

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

4. Cable clamps and several grommets are provided with the cable clamp kit for securing cables to the chassis. More than one grommet may be needed to secure cables in the clamp.

5. Adjust cables leaving an 8–inch service loop within the chassis, this allows blades to be withdrawn. Tighten the compression fitting screws to secure cables at the cable entry location.

6. Use Mille-Ties to secure cables to sliding blade. See Figure 7 .

Caution: Always allow sufficient fiber length to permit routing without severe bends. Non bend-

optimized fibers may be permanently damaged if bent/curved to a radius of less than 1.5 in.

(3.81 cm).

7. Before connecting fibers to adapters pull blade out to the second detent. Radius limiters are provided on the blade for slack fiber storage.

FIBER

FANOUT

LC

CONNECTOR

MILLE-TIE

8-INCH

SERVICE

LOOP

CABLE

CLAMPS

Figure 7. 900 Micron Fiber Installation

24481-A

Page 11

© 2011 Tyco Electronics Corporation.

ADCP-92-319 • Issue 1 • 5/2011

4 CUSTOMER INFORMATION AND ASSISTANCE

PHONE:

U.S.A. or CANADA

Sales:

Extension

1-800-366-3891

73347

Technical Assistance: 1-800-366-3891

Extension 70500

WRITE:

Tyco Electronics Corporation

PO Box 1101

Minneapolis, MN 55440-1101, USA

PRODUCT INFORMATION AND TECHNICAL ASSISTANCE:

[email protected]

REPRINTS:

PDF copies of manuals are available for downloading at the following link: www.adc.com/manuals

ADCP Number:

923 19

Contents herein are current as of the date of publication. TE reserves the right to change the contents without prior notice. In no event shall TE be liable for any damages resulting from loss of data,

loss of use, or loss of profits and TE further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period.

24140-E

Page 12

© 2011 Tyco Electronics Corporation.

advertisement

Related manuals