XN3210_3410 manual_060410 R2.ind1 1
Owner’s manual & Installation manual
Mode d’emploi et manuel d’installation
Manual de instrucciones y de instalación
XN 3210
XN 3410
XN AMPLIFIERS
AMPLIFICATEURS XN
AMPLIFICADORES XN
9/3/2010 8:49:17 AM
INTRODUCTION
The Clarion XN3210 is a full-featured, two-channel amplifier incorporating the following features:
• Specially coated circuit boards that resists mold, mildew and moisture damage.
• Pulse-Width Modulated (PWM) MOSFET power supply for maximum
performance with minimal distortion.
• Remote turn-on with "soft start" muting to prevent turn-on "thump".
• Variable high-pass/low-pass electronic crossover with a 12dB per octave
slope (adjustable range: 55Hz to 5.5kHz).
• Variable bass boost circuit to reinforce low frequency signals that may be lost
due to subwoofer enclosure design.
• Adjustable input level controls with ground loop isolation to minimize noise
and distortion.
• 2-ohm stereo stable, 4-ohm mono stable.
• Chrome-plated power, speaker and RCA connections.
• Speaker level input.
• Low profile construction with aluminum heat sink for efficient heat dissipation.
The Clarion XN3410 is a full featured, four-channel amplifier adding the following feature:
• Advanced circuitry design featuring bridgeable and mixed mode operation for
use in various system configurations including 4, 3, or 2 channel systems.
ABOUT THE MANUAL AND WARRANTY
This manual describes the basic requirements to install the Clarion XN3210 and
XN3410 amplifiers. The installation of this amplifier can be quite complex to install.
If you do not posses the necessary knowledge and tools to perform this installation, please contact your local Clarion Marine Audio dealer.
Keep all instructions and sales receipt for future reference and warranty information.
Warranty information can be found on page 19 of this manual.
TABLE OF CONTENTS
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Input Connections and Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connections for Power and Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wiring Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
XN3410 Wiring and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
XN3210 Wiring and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the Subwoofer Bass Boost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Final System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Product Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
XN3210/XN3410
3
XN3210_3410 manual_060410 R2.ind3 3 9/3/2010 8:49:17 AM
DESCRIPTION
The XN3210 and XN3410 use an unregulated MOSFET power supply for superior sound and output wattage. In addition, a toroid-coil is used to transfer power with minimal performance loss due to heat. To avoid unwanted noise, a doublesided conformal printed circuit board with strategically placed components keeps
AM RFI subdued.
All of the connections and controls for the XN3210 and XN3410 are conveniently located at the ends of the amplifier and labeled appropriately. To ensure the best possible electrical connections, the power, speaker, and RCA inputs are goldplated. An additional benefit of the XN3410 is the ability to create a 2, 3, or 4 channel amplified system with a flip of a switch (see Application section). In the event of component failure or a short circuit, the XN3210 and XN3410 incorporate safe guards and outboard ATC fuses to prevent damage to the amplifier.
INPUT CONNECTIONS AND AUDIO CONTROLS
The front panel of the XN3410 and XN3210 contain both connections for RCA and speaker level inputs, along with the audio controls as shown below.
Fig. 1
XN3410
2 3 4 5 6 7 8 9 16
CH1 INPUT
CH1-CH2
HIGH INPUT
+ CH1
– CH1
+ CH2
– CH2
GND
2-CH-IN
CH2
CH3
CH4
MAX
MIN
CH1/2
GAIN
CH3/4
BASS
BOOST
CH1/2
SOURCE
SELECT
MAX
0
dB
15
MIN
2CH
BASS
CH 1/2 FREQ Hz
110
55
240
550
330 LPF
CH 1/2
X-OVER
HPF OFF
2CH
CH1/2
STEREO
MODE
CH1/2
MONO
CH3/4
CH1
MONO
POWER
4CH
55
CH 3/4
FREQ Hz
110
240
CH2
MONO
RANGE
550
330
X1
X10
STEREO CH3/4
MONO
CH 3/4
X-OVER
LPF HPF OFF
CH3-CH4
HIGH INPUT
CH3 +
CH3 –
CH4 +
CH4 –
GND
1
11 12 13 14 15 10
1. CH1-CH2 High Input
2. CH1/CH2 RCA Input
3. CH3/CH4 RCA Input
4. CH1/CH2 Gain Control
5. CH3/4 Gain Control
6. Bass Boost
7. Source Select
8. CH1/2 Mode Switch
9. CH3/4 Mode Switch
10. CH3-CH4 High Input
11. CH1/2 Frequency Control
12. CH1/2 Crossover Mode Switch
13. CH3/4 Frequency Control
14. Frequency Range Multiplier
15. CH3/4 Crossover Mode Switch
16. Power Light Indicator
4
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind4 4 9/3/2010 8:49:19 AM
XN3210
1 2 3 4 5 6 7 9
HIGH
INPUT
+ CH1
– CH1
+ CH2
– CH2
GND
INPUT
MIN
MAX
GAIN
CH1
BASS
BOOST
0
dB
15
FREQ Hz
55
110
240
FREQ
RANGE
550
330
X1
X10
X-OVER MODE
LPF HPF OFF STEREO
CH2
MONO
CH1/2
MONO
POWER
CH2
8
1. CH1-CH2 RCA Input
2. Gain Control
3. Bass Boost
4. CH1/CH2 Frequency Control
5. Frequency Range Multiplier
6. Crossover Mode Switch
7. Output Mode Selector Switch
8. High Input
9. Power Light Indicator
The RCA connections are gold plated for optimum performance and low signal loss.
The RCA connectors are labeled CH1 (front left), CH2 (front right) [for XN3410:
CH3 (rear left), and CH4 (rear right)]. In applications where RCA signals are not present, the speaker level output from the head unit can be used. (Use one or the other input, not both.)
• Gain Controls: For the XN3410, separate CH1/2 and CH3/4 gain controls
allow you to set the nominal operating level of the amplifier. The amplifier's input
range, 200mV to 6.0V for RCA inputs and 500mV to 13V for speaker level inputs,
can accommodate input levels from virtually any head unit.
• Bass Boost: The amplifier features a "high-Q" (i.e. narrow frequency band)
Bass Boost circuit. It acts much like an equalizer with an adjustable gain from 0 to
+15dB fixed at 45Hz. Use this feature to tune low-frequency audio response to
compensate for a less than ideal subwoofer enclosure design. The added boost
produces rich, full bass tones that are normally difficult to reproduce in the marine
audio environment.
NOTE: Bass Boost setting should only be used for subwoofer applications.
• Source Select (XN3410 only)
2CH BASS: Uses CH1/2 inputs and has output from all 4 channels with Bass
Boost.
2CH: Uses CH1/2 inputs and has output from all 4 channels. The Bass Boost
will work only on CH1/2 and have no effect on CH3/4.
4CH: Uses all 4 channel inputs and has output from all 4 channels. The Bass
Boost will work only on CH1/2 and have no effect on CH3/4.
XN3210_3410 manual_060410 R2.ind5 5
XN3210/XN3410
5
9/3/2010 8:49:20 AM
• Output Mode Selector Switch: CH 1/2 and CH 3/4 (XN3410 only)
STEREO: Full left and right stereo operation.
CH1Mono / CH2 Mono: Single channel input for bridged operation. This is
especially useful in high-powered systems. (Uses CH2 and CH4 inputs.)
CH1/2 Mono / CH3/4 Mono: Allows for a stereo input to be summed into a mono
output.
• CH1/2 FREQ / CH3/4 FREQ (XN3410 only) The CH1/2 crossover frequencies
are adjustable from 55Hz to 550Hz. While CH3/4 crossover frequencies are
adjustable from 55Hz to 5500Hz (via the Frequency Range Multiplier) for a wider
range of crossover points. Use this feature along with your speaker
manufacturer's recommended crossover frequencies to quickly design a more
advanced system.
NOTE: If either of the Crossover Mode Switches is set to OFF, varying the
frequency control will have no effect.
• CH1/2 Filter / CH3/4 Filter (XN3410 only) A filter is activated by sliding the
CH1/2 and CH3/4 filter switch to either HP = High Pass or LP = Low Pass.
CH1/2 is fully adjustable from 55-550Hz (via CH1/2 Freq) and CH3/4 is fully
adjustable from 55-5500Hz (via CH3/4 Frequency and Frequency Range
Multiplier). Use this feature along with your speaker manufacture's recommended
crossover frequencies to design a more advanced system.
CONNECTIONS FOR POWER AND SPEAKERS
The rear panel of the XN3410 and XN3210 contains power and speaker connections as shown below.
Fig. 2
XN3410
1 2 3 4 5 6
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
7
1. CH1 Speaker Output
2. CH2 Speaker Output
3. Ground
4. Remote Turn-on
8
5. Battery +12V Input
6. (2) - 30 Amp Fuse
7. CH3 Speaker Output
8. CH4 Speaker Output
6
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind6 6 9/3/2010 8:49:20 AM
XN3410 - Electrical Connection
Remote Turn-On
F
U
Fig. 3
XN3210
CH1 Speaker ( +)
CH1 Speaker ( -)
CH2 Speaker ( +)
CH2 Speaker ( -)
1 2
4 Ω BRIDGED
+ CH1 – + CH2 –
GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
CH4 Speaker ( -)
CH4 Speaker ( +)
CH3 Speaker ( -)
CH3 Speaker ( +)
3 4 5 6
4 Ω BRIDGED
+ L – + R –
GND REM +12V
FUSE
40A
1. Left Speaker Output
2. Right Speaker Output
3. Ground
XN3210 - Electrical Connection
4. Remote Turn-on
5. Battery
6. 40 Amp Fuse
Remote Turn-On
F
U
S
E
4 Ω BRIDGED
+ L – + R –
GND REM +12V
FUSE
40A
Left Speaker ( -)
Left Speaker ( +)
Right Speaker ( -)
Right Speaker ( +)
XN3210_3410 manual_060410 R2.ind7 7
XN3210/XN3410
7
9/3/2010 8:49:23 AM
INSTALLATION
This section suggests Mounting and Wiring Precautions for installing the Clarion
XN3210 and/or XN3410 amplifier(s). If you do not posses the necessary tools and installation experience, do not attempt to install these amplifiers. Instead, contact your local Clarion Marine Audio dealer to perform the installation.
MOUNTING PRECAUTIONS
Prior to mounting the amplifier, make sure it is safe to mount the amplifier in that location. Failure to do so can result in serious damage to the boat. In addition, stainless steel hardware should be used to mount the amplifier and additional accessories. When possible, use a nut and bolt with a lock washer to secure the amplifier. Extra care and attention is necessary in marine installations due to the uncertainty of water conditions.
Additional precautions and suggestions:
1. For the most efficient cooling, mount the amplifier so cool air runs along the
length of the heat sink, rather than across them. To increase air movement and
circulation, a cooling fan can be installed.
2. Mount the amplifier on a rigid surface; avoid mounting to subwoofer enclosures or
areas prone to vibration.
3. Prior to drilling and holes, make sure the proposed mounting holes will not cut
into the fuel tank, fuel lines, electrical wiring, or through the boat.
4. Do not mount the amplifier where it is susceptible to water.
WIRING PRECAUTIONS
Read all of the wiring precautions prior to making any connections. If you are unsure and/or don't have the necessary installation hardware, contact your local
Clarion Marine Audio dealer to perform the installation.
1. Before you begin the installation, make sure the source unit Power switch is in the
OFF position.
2. Disconnect the negative (-) lead of the battery (or batteries) before making any
power connections.
3. When making connections, be sure that each connection is clean and secure.
Insulate final connections with electrical tape or shrink tubing. Failure to do so
may damage your equipment.
4. A good ground is critical for the performance of the amplifier. A ground wire
should be run directly from the battery to the amplifier. Use black insulated
10-gauge or larger wire for the amplifier's ground (-) power lead.
5. Add an additional fuse holder and fuse at the positive (+) terminal of the battery.
The fuse rating should equal the total current consumption at full output of the
amplifier(s). Use red insulated 10-gauge or larger wire for the amplifier's positive
(+) power lead. Do not install the fuse until the complete installation has been
performed.
6. When replacing the amplifier's fuse, always use one having the same amperage
rating. Substituting a higher rated fuse or a slow-blow type can result in serious
damage to the amplifier.
8
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind8 8 9/3/2010 8:49:23 AM
7. When creating passage holes for power cables, RCA's cables, and speaker wires,
use grommets to eliminate any sharp edges created during drilling. This will
protect the wire from being nicked and causing a short circuit.
8. Extra cable can cause signal loss and act as an "antenna" for noise. Use only
high-quality RCA cables that are no longer than necessary.
9. In multiple amplifier systems, it is recommended to use a relay on the remote
turn-on lead of the radio.
XN3410 WIRING AND APPLICATIONS
The Clarion XN3410 4-channel marine audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation.
Fig. 4
4-Channel Full Range Stereo System
CH1 Speaker CH2 Speaker
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
CH3 Speaker CH4 Speaker
In this application, the XN3410 is used as a 4-channel amplifier to drive four full range speakers in stereo.
XN3210_3410 manual_060410 R2.ind9 9
XN3210/XN3410
9
9/3/2010 8:49:24 AM
Fig. 5
4-Channel Stereo System,
2-Channel High-Pass, 2-Channel Low-Pass
CH3 Speaker System
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
CH4 Speaker System
CH1 Subwoofer CH2 Subwoofer
In this 4-channel system, the XN3410 drives a pair of stereo satellites for the front and a pair of subwoofers. Note the filter settings.
10
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind10 10 9/3/2010 8:49:25 AM
Fig. 6
2-Channel Stereo System with Low-Pass Bridged Mono Channel
CH3 Speaker System
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
CH4 Speaker System
Subwoofer
The XN3410 can also be used to drive a pair of stereo satellites for the front and a single mono subwoofer for the rear. Note the filter settings.
XN3210_3410 manual_060410 R2.ind11 11
XN3210/XN3410
11
9/3/2010 8:49:26 AM
Fig. 7
2-Channel High Power System (Satellite or Subwoofer)
Bridged CH1/CH2
Speaker System
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
Bridged CH3/CH4
Speaker System
OR
Bridged Left Subwoofer
Bridged Right Subwoofer
The XN3410 can be set up as a 2-channel high power amplifier to drive a pair of satellites (or subwoofers)
12
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind12 12 9/3/2010 8:49:27 AM
Fig. 8
Mixed Mode System On CH3/CH4, Full Range Speakers On CH1/CH2
CH3 Speaker
C
4 Ω BRIDGED
+ CH1 – + CH2 – GND REM +12V
30A
FUSE
30A
+ CH3 – + CH4 –
4 Ω BRIDGED
CH4 Speaker
C
CH1
Speaker
L
Subwoofer
CH2
Speaker
FREQ (Hz) L (mH) C ( F)
80
100
125
150
200
8.0
6.4
5.1
4.2
3.2
497
398
318
265
199
NOTE: Chart values based on 4 Ohm speakers.
The amplifier can be configured for a mixed-mode operation on either channels 1/2 or 3/4 amplifier sections. The table provides component values to create a 6dB per octave crossover at specified frequencies. Use components that have a + 5% tolerance and capacitors rated at 100V.
NOTE: Choose the same frequency for both LP and HP crossovers. Do not overlap frequencies, as this may damage the amplifier.
XN3210/XN3410
13
XN3210_3410 manual_060410 R2.ind13 13 9/3/2010 8:49:28 AM
XN3210 WIRING AND APPLICATIONS
The Clarion XN3210 2-channel marine audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation.
Fig. 9
Bridged - Mono Subwoofer System
4 Ω BRIDGED
+ L – + R –
GND REM +12V
FUSE
40A
Set X-Over Mode to LPF and adjust
FREQ to speaker specifications.
Subwoofer 4 Ohms
In this application the amplifier is bridged for mono operation to drive a subwoofer.
Note the filter settings.
14
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind14 14 9/3/2010 8:49:29 AM
Fig. 10
2-Channel Full-Range, Satellite, or Subwoofer Stereo System
(Set INPUT SELECT Switch to STEREO)
4 Ω BRIDGED
+ L – + R –
GND REM +12V
FUSE
40A
Left Full Range Speaker
Left Component
Speaker System
Right Full Range Speaker
Set X-Over Mode as shown.
Right Component
Speaker System
Set X-Over Mode as shown.
Adjust FREQ to speaker specifications.
Set X-Over Mode as shown.
Adjust FREQ to speaker specifications.
Left Subwoofer Right Subwoofer
In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers.
Note the filter settings.
XN3210_3410 manual_060410 R2.ind15 15
XN3210/XN3410
15
9/3/2010 8:49:30 AM
Fig. 11
Mixed-Mode Satellite and Subwoofer System
(Set INPUT SELECT Switch to STEREO)
4 Ω BRIDGED
+ L – + R –
GND REM +12V
FUSE
40A
Left Speaker
C
C
Right Speaker
L
Subwoofer 4 Ohms
FREQ (Hz)
80
100
125
150
200
L (mH)
8.0
6.4
5.1
4.2
3.2
C (µF)
497
398
318
265
199
NOTE: Chart values based on
4 Ohm speakers.
The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies.
Use components that have a + 5% tolerance and capacitors rated at 100V.
NOTE: Choose the same frequency for both LP and HP crossovers. Do not overlap frequencies, as this may damage the amplifier.
16
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind16 16 9/3/2010 8:49:30 AM
SETTING THE GAIN
After completing the installation, follow these steps to set the Gain Control and then perform the Final System Check.
1. Turn the Gain Control all the way counter-clockwise.
2. Turn the ON/OFF Switch on the source units to the ON position. Set all Tone or
Equalization Controls to "flat" positions and turn Loudness off.
3. Play a CD, set the Volume Control at 75% of full level.
NOTE: If the system uses an equalizer, set its frequency controls to "flat"
positions.
4. Slowly increase the Gain Control. Stop when you hear a slight distortion of audio.
SETTING THE CROSSOVER
The Clarion XN3210 and XN3410 feature fully adjustable high and low pass crossovers. To set the crossover, follow these steps.
1. Using the X-Over Mode Switch, select the desired mode: LP for Low Pass, HP
for High Pass or OFF for Full Range.
2. Using the Freq (Hz) Selection Control, select the desired frequency. If the
desired frequency exceeds the range of the Freq (Hz) Selection Control, press
the Crossover Frequency Multiplier Switch to increase the value by a multiplier
of 10.
• For example, 55Hz x 10 = 550Hz or 550Hz x 10 = 5.5kHz.
3. Repeat steps 1 and 2 for both the CH1/CH2 and CH3/CH4 crossovers on the
XN3410.
SETTING THE SUBWOOFER BASS BOOST
1. Initially set the Bass Boost control to its full left position (i.e. 0dB).
2. Listen to a variety of music styles (e.g. Rock, Rap, etc.) and slowly increase
the Bass Boost control until a noticeable increase in low bass response is
perceived.
3. Slowly adjust the Bass Boost control (up or down) to realize the best bass
response.
CAUTION: If you hear a "pop" (due to speaker over-excursion), lower the
Bass Boost to prevent speaker damage. If the system sounds muddy and
distorted (due to amplifier clipping), lower Bass Boost to avoid shutdown from
overheating.
XN3210_3410 manual_060410 R2.ind17 17
XN3210/XN3410
17
9/3/2010 8:49:31 AM
FINAL SYSTEM CHECK
1. Turn on the source unit. After a two-second delay, slowly increase the Volume
Control and listen to the audio. If you hear any noise, static, distortion or no
sound at all, check the connections and refer to the Troubleshooting section.
Depending on your system design, the levels may become quite loud even at
low Volume Control settings. Until you get an "audio feel" of the system's power,
use care when adjusting controls.
2. Turn the Balance Controls to their extreme positions and listen to the results.
Audio imaging should match control settings (audio from the left speaker when
balance is left).
3. Increase the volume and verify that the amplifier reproduces audio (at full
frequencies) without distortion. If you hear distortion, check the connections and
verify that the Gain Control is set correctly. Another possibility is damaged
speakers or under-powered speakers. Refer to the Troubleshooting section for
additional help.
TROUBLESHOOTING
Problem
No Audio.
Solution
Low or no remote turn-on voltage. Check remote connections at amplifier and source unit.
Blown amplifier fuse. Replace with new fast-blow fuse (same rating).
Power wires not connected. Check battery and ground wiring at amplifier; also check battery connections.
Speaker leads shorted. Check speaker continuity to ground, it should not show a common ground.
Speakers not connected or are blown. Check speaker connections at amplifier, measure coil impedance.
Problem
Audio cycles on and off.
Solution
Thermal protection circuits are shutting amplifier off. Check location for adequate ventilation; consult an authorized Clarion dealer.
18
XN3210/XN3410
XN3210_3410 manual_060410 R2.ind18 18 9/3/2010 8:49:31 AM
Problem
Distorted audio.
Solution
Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.)
Problem
Audio lacks punch.
Solution
Speakers wired incorrectly, which causes cancellation of bass frequencies.
Check polarity of wires from amplifier to each speaker as defined by the system design.
Problem
Amplifier fuse keeps blowing.
Solution
Incorrect wiring or short circuit. Review Installation and check all wiring connections.
Problem
Whining or ticking noise in the audio with engine on.
Solution
Amplifier is picking up alternator noise or radiated noise. Turn down input gain; move audio cables away from power wires. Check power and ground connections on amplifier; install an in-line noise filter on source unit's power wire; check alternator and/or voltage regulator; test for weak battery or add water to battery.
PRODUCT SPECS
MODEL
Frequency Response
Signal To Noise Ratio
THD
Input Sensitivity
Low Level
Input Sensitivity
Speaker Level
Max. Power Output
Cont. Power Output
2-Ohm Stereo Output
Bridged Power
Dimensions
Current Consumption output @ max power
XN3410
20Hz ~ 20kHz
>97db
.10% all channels driven
200mV ~ 6.0V
500mV ~ 13V
720W (180W x4)
165W x 4 @ 1.0% THD
330W x 2 @ 1.0% THD
2-9/16" H x 9" W x 17-3/4" L
58A @ 720 Watts
XN3210
20Hz ~ 20kHz
>95db
.10% all channels driven
200mV ~ 6.0V
500mV ~ 13V
360W (180W x2)
180W (90W x2) @ 1.0% THD
150W x 2 @ 1.0% THD
250W x 1 @ 1.0% THD
2-9/16" H x 9" W x 13" L
29A @ 382 Watts
XN3210/XN3410
19
XN3210_3410 manual_060410 R2.ind19 19 9/3/2010 8:49:31 AM
