MEMORY HiCORDER MR8870 - Batenburg Mechatronica

MEMORY HiCORDER MR8870 - Batenburg Mechatronica
MEMORY HiCORDER MR8870
Oscilloscope-like Waveform Observation,
Plus Recording of RMS Variations - In a Single Device!
RMS recording function makes its debut on this device!
Enhancing the ultra-compact oscilloscope-functioning Hioki 8870, the new MR8870 features a new
RMS recording mode and real-time save to a CF card.
n
n
n
n
Measure safely, with isolated input for all channels
Bundled PC application enables integration/observation of synchronized data from two
HiCORDERs on a single screen
Test commercial power lines with ease of mind thanks to isolated input for both channels
Monitor instantaneous waveforms on-site
High-speed waveform observation/recording with 1 M sampling, despite compact size
Monitor fluctuations in commercial power lines
Real-time recording of data to CF card with 1 ms/sampling recording interval in a compact package
Synchronize two HiCORDERs together to measure three-phase lines and other
channels needing three or more channels
2
Memory
Recorder
An oscilloscope in the palm of your hand
Capture unpredictable phenomena using waveforms !
n Recording of EV and HEV starting current waveforms
n Check inverter output waveforms
Use the MR8870 with the
Inverter performance analysis
Clamp On AC/DC Sensor
requires simultaneous obser-
CT9693 to obser ve the
vation of the high frequency
current waveform when
carrier signal and the low
starting an EV or HEV. The
frequency fundamental wave-
clamp’s characteristics
for m being switched. The
enable it to accommodate
combination of high-speed
a broad range of frequencies from DC to 10 kHz and
The photograph shows the MR8880, the MR8870’s four-channel
sister product.
higher.
sampling capability and highcapacity memory make these
observations possible. For current waveform observations,
use Hioki clamp sensors capable of high-frequency measurements without direct electrical contact.
n Recording of motor rush current
n CB timing measurements
M o t o r p o w e r- o n i n r u s h c u r r e n t
Analyze the relationships of multi-point logic signals and
waveforms can be precisely recorded.
analog waveforms to detect timing issues that can affect
The Clamp On Probe the 9018-50 is
power supply circuit breakers. Use
available for current measurement,
logic probes to record relay operations
as is the Clamp On Leak HiTester 3283.
on up to four channels, or use the
In addition, to measure direct current
Differential Probe P9000 for 440 v
waveforms, a variety of Current meters
power line measurements and for
such as the CLAMP ON AC/DC HiTESTER
support of CAT III 600 V measurement
3284/3285 are available upon request.
categories.
3285
CAT III 600 V
9018-50
With the Memory HiCorder connection requires Output
Cord 9094 and Conversion Adapter 9199
n Analysis of sequence controller issues
When sequence controllers being used in applications such
as production and testing lines stop due to errors or generate warning output, potential causes include momentary AC
power interruptions and brownouts. The MR8870 is ideal for
analyzing the operation of such systems since it can record
the correlation of sequence relay signals, AC power circuits,
and DC voltage circuits as
waveforms using power
supply anomalies as a trigger.
CAT IV 600 V
For high voltage measurement
DIFFERENTIAL PROBE P9000-01, P9000-02
9322
For high voltage measurement
DIFFERENTIAL PROBE 9322
3
RMS
Recorder
A pen-free recorder in the palm of your hand
Long-term RMS fluctuation recording !
Pen- and paper-free recording
A substitute for the Hioki Micro HiCorder
n AC RMS data recording
Use the device in conjunction with an AC voltage input and
a clamp current sensor to record RMS values for current.
Input instantaneous waveforms are acquired via high-speed
sampling at 200 μsec. RMS data is staggered at a rate of
1000 times per second as it is computed – not even abrupt
fluctuations will escape notice.
The photo above shows the Hioki 8205-10 and 8206-10 Micro HiCorders. These
products are no longer available.
n RMS data recorded in internal memory
The RMS recorder can output data into the internal memory
RMS value calculation method
at rates of up to once per millisecond. Internal memory
RMS values for three AC waveform cycles are calculated 1,000 times
every second (see figure below). Readings other than maximum and
minimum values are eliminated based on the set recording interval,
and the resulting data is displayed and saved.
recordings of up to 10,000 div (1 million data items) are
supported. Furthermore, if you set automatic saving to
storage media, the device writes data to the media (at each
recording interval) in real time as it makes measurements.
* A new data file is created for each 10,000 div worth of data.
* It is possible to save the data repeatedly up until the media’s full capacity is reached,
but after that periods of dead time (when measurement is not possible) will occur every
10,000 div.
Duration of 3 cycles
Duration of 3 cycles
1/1000 sec
4
Compact and lightweight
Small-bodied design for ease of portability
Volume is just 30% and weight just 40% of Hioki's 4-channel
Memory HiCorder, the MR8880 – a 70% and 60% reduction,
respectively.
A waveform measurement instrument that
101 mm
(3.98 in)
you can slip into your briefcase and carry
anywhere. Should you suddenly discover you
need it on a work trip, you can simply take it
out and begin to use it, just as you would a
176 mm
(6.93 in)
tester.
41 mm
(1.61 in)
Intuitive, no-fuss operation
Built-in Setup Wizard to help you get started
Activate the Setup Wizard
Real-Time waveform monitoring
When powered on, the Settings screen appears along with the
The help text cr awls along the bot tom of the screen,
waveform monitor, and the new Setup Wizard blinks.
describing the function of the setting at the blinking cursor.
By activating the Setup Wizard, you can easily navigate by
The enhanced “Waveform Monitor” window with level meter
following the simple instructions. Soon you will be operating
display facilitates changes to settings by simultaneously
the device like a seasoned professional.
displaying real-time input waveforms.
Select mode at start-up
No unnecessar y fuss before you can star t working.
You select which measurement mode to use (memory
recorder or RMS value recorder) when you switch on the
device.
Choose the mode once, and you’ll never need to select it
again.
5
Data analysis in tandem with a PC
Dedicated PC application program bundled as standard accessory
n Pseudo real-time MEM data recording to media
With automatic saving, the memor y recorder saves
instantaneous waveform data into the media in batches.
Data is saved to media using a method designed to
minimize the time for which measurement is not possible
(dead time). As a result, in the 50-ms/div-and-slower range of
the time axis, the device writes
data from each sampling to the
media in real time as it makes
measurements.
* Data is saved up to the set recording length.
n Binary data (MEM/RMS data) loadable into PC
You can copy data saved on the CF card to a PC in two
ways: via the card, or by connecting the MR8870 to the
PC with a USB cable. The bundled PC application lets you
display waveforms on the PC and print them out.
* The MR8870 is not provided with a communication function for controlling it from a
PC connected to it with a USB cable.
n Synchronize two HiCorders together for 4ch
recording! (MEM data)
For those times when 2-channels are just not enough,
synchronize two MR8870’s using the external trigger I/
O terminals (apply the trigger output from one to the
lUse the bundled software to composite waveform files.
For example, to monitor the waveforms of a 3P 200 V line,
you can use two HiCorders at the same time and view the
waveforms of all 4 channels on the same screen on the PC.
exter nal tr igger input of the
other). Then use synchronous
star t to automatically record
four channels of measurement
data to a CF card.
n Waveform display and printing, and CSV conversion
with PC (MEM data, RMS data)
Open a data file with the dedicated Wave Processor (PC
application program) for the MR8870/8870, to import
n Features of the Dedicated Wave Processor Program (supplied
accessory)
l Designed especially for MEMORY HiCORDER MR8870/8870
Application program displays and prints waveforms, and converts
measurement data to CSV text files on a Windows PC.
and print waveforms with your own arrow and figure
l Provides X-Y display capability not available on the HiCorder
annotations. Of course, screen data can be copied and
l Generate reports using templates, with figure annotations and entered
pasted into common Word and Excel documents to easily
create reports.
comments
l Multiple files can be batch-converted to CSV data
l Use two HiCorders to monitor 3 or 4 channels of waveforms that are
measured using the same time axis range on the same PC window.
6
■ Specifications
(Accuracy guaranteed for 1 year, Post-adjustment accuracy guaranteed for 1 year)
Basic specifications
Measurement functions Memory recorder (high-speed recording), RMS recorder (50/60 Hz, or DC only)
2 analog and 4 logic channels (For analog inputs, channels are isolated
form each other and from frame GND. For logic terminals, all channels
No. of channels
has common GND.)
Maximum sampling rate 1 MS/s (1 μs period, all channels simultaneously)
Memory capacity 12 bits × 2 M-Words/ch
CF card Type I slot (standard equipment) ×1: Up to 2 GB, supports FAT, or
FAT-32 format
Removable
Memory items: Setting condition, measurement data (binary or text),
storage
screen shot, result of numerical calculation, reduced text saving data
Clock and settings: 5 years or more (@25°C 77°F)
Waveform backup function: available when Battery pack 9780 is
Backup function
installed with charge remaining or AC adapter is connected (up to
Control terminals
External interface
100 hours with fully charged battery pack).
Terminal block: External trigger input, trigger output
USB: USB 2.0, mini-B receptacle ×1 port,
Function: Transfer files from the installed CF card to a PC via
USB cable, but communication functions such as the capability to
change HiCorder settings from the PC are not provided.
Display type
4.3-inch TFT color LCD (480 × 272 dots)
Display resolution
Waveform section: 20 div (time axis) × 10 div (voltage axis)
(1 division = 20 dots × 20 dots)
MR8870-20: English, Japanese (Default settings: English)
Display languages MR8870-30: Chinese, English, Japanese (Default settings: Chinese)
Note: Korean (special order only, please contact Hioki)
Environmental condi- Operation: 0°C (32°F) to 40°C (104°F), 80 % rh or less
tions (no condensation) Storage: -10°C (14°F) to 50°C (122°F), 80 % rh or less
Compliance
standard
Safety: EN61010,
EMC: EN61326, EN61000-3-2, EN61000-3-3
• AC Adapter Z1005: 100 to 240 V AC, 50/60 Hz
• Battery pack 9780: continuous operation times: approx. 2 hours
Power supply
(reference value at 25°C/77°F, waiting for trigger) (AC adapter has priority
when used in combination with battery pack)
• DC power supply: 10 to 16 V DC (please contact your Hioki distributor
Memory recorder (high-speed recording)
Measurement
targets
Time axis
Sampling period
Power
consumption
pack 9780)
3 VA max. (When using the battery pack 9780)
The installed battery pack charges when the AC adapter is connected.
Charging functions Charging time is about 200 minutes (reference value at 25°C/77°F)
100 μs to 5 min/div (100 samples/div) 20 ranges
Time axis zoom: ×2 to ×10 in 3 stages, compression: 1/2 to 1/1000
in 9 stages
1/100 of time axis range (minimum 1 μs period)
Recording length
20 to 20,000 div, or continuous (available at 50 ms/div to 5 min/div only)
Pre-trigger
Record data from before the trigger point at 0 to 100% of the
recording length in 13 stages
• Numerical calculation: Up to four simultaneous calculations (common
to all channels), calculation results are saved to CF card
• Calculation contents: average, peak-peak, maximum and minimum values, RMS, period and frequency
• Calculation range: specified by A/B cursors or whole recording length
• Waveform processing: N/A
Calculation
functions
Note: limited by timebase, only the last 20,000 div are saved
n Recording Time to internal memory using memory recorder mode (abridged)
• If you set automatic saving of binary-format data to the CF card in the 50-ms/div-and-slower range of the
time axis, data is saved simultaneously with measurement. This considerably reduces the amount of dead
time (the period from the completion of the saving of internal memory data (of the applicable capacity below)
to the CF card, to when measurement/recording begins again). This is a new function – the MR8870 is the
first in the series to feature it.
• The possible length of a single measurement/recording is the length given below for the applicable time axis
range.
• The maximum recording length is the same whether 1 or 2 channels are used.
• The internal memory capacity is 4 MB/channel. Media capacity depends on the card (for example, 512 MB).
Time axis
Sampling period
Recording length 20,000 div Max.
1 div = 100 sampling data
100 μs/div
1 μs
2s
1 ms/div
10 μs
20s
10 ms/div
100 μs
3min 20s
100 ms/div
1 ms
33min 20s
for connection cord, max. 3 m/9.84 ft length)
30 VA max. (When using the AC adapter and charging internal battery pack 9780)
10 VA max. (When using external DC power supply and charging internal battery
Instantaneous waveform of DC to AC waveform recording / monitor
1 s/div
10 ms
5h 33min 20s
10 s/div
100 ms
2d 07h 33min 20s
1 min/div
600 ms
13d 21h 20min 00s
5 min/div
3.0 s
69d 10h 40min 00s
Notes: Charging time depends on battery condition. Charging is disabled to
protect the battery at ambient temperatures out of 5°C (41°F) to 30°C (86°F).
Dimensions and
mass
Accessories
Approx. 176 mm (6.93 in) W × 101 mm (3.98 in) H × 41 mm (1.61 in) D,
600 g (21.2 oz) (with the Battery pack 9780 installed)
Instruction Manual ×1, Measurement Guide ×1, AC adapter Z1005 ×1,
Strap ×1, USB cable ×1, Application Disk (Wave Processor Program for
the 8870) ×1, Protection sheet 9809 ×1
Trigger functions (For memory recorder only)
Trigger modes
Single, continuous
Two analog channels, four logic channels, external trigger (falls
below 2.5 V, or shorted terminals),
Trigger sources
ON/OFF switching of each source, AND/OR between sources,
manual triggering
• Level: Triggering occurs when preset voltage level is crossed
(upwards or downwards)
• Voltage drop: Triggering occurs when voltage drops below peak
Trigger types
(Analog)
voltage setting (for 50/60 Hz AC power lines only)
• Window: Triggering occurs when window defined by upper and
lower limit is entered or exited
Level setting resolution 0.5% f.s. (f.s.=10 divisions)
Trigger types (Logic) 1, 0, or ×, Pattern setting
Set by the number of samples, from 0 to 100 samples, in five steps
Trigger filter
Trigger output: open collector 5 voltage output, active low with at
Other functions
least 1 ms pulse width
Analog Input
(Accuracy at 23 ±5°C/73 ±9°F, 80 % rh or less, after 30 minutes of warm-up time)
Measurement functions Number of channels: 2, for voltage measurement
Isolated BNC connector (input impedance 1 MΩ, input capacitance 7 pF)
Max. rated voltage to earth: 300 V AC, DC, CAT II (with input isolated
Input connectors
Measurement
range
from the unit, the maximum voltage that can be applied between input
channel and chassis and between input channels without damage)
10 mV to 50 V/div, 12 ranges, full scale: 10 div, AC voltage for possible
measurement/display using the memory function: 280 V rms,
(at Memory recorder) Low-pass filter: 5 /50 /500 /5 kHz
Measurement
1/100 of measurement range (using 12-bit A/D conversion, measurement
range is ±10 times range value)
resolution
Highest sampling rate 1 MS/s (simultaneous sampling in 2 channels)
±0.5 % f.s. (after zero-adjust, in measurement range, f.s. = 10 div)
Accuracy
Frequency characteristics DC to 50 kHz -3dB
DC / GND
Input coupling
Max. allowable
400 V DC (the maximum voltage that can be applied across input pins
without damage)
input
• Numerical value display: instantaneously value, or RMS value (DC, or
Display functions
50/60 Hz only) (cannot select at measuring)
• Waveform display zoom at voltage axis ×2 to ×10, compression ×1/2, ×1/5
Note: X-Y display N/A (X-Y possible on PC screen by supplied software only)
RMS recorder (high-speed recording)
Measurement
targets
Measurement
mode
Commercial power line (50 ±1 Hz/ 60 ±1 Hz), DC
Note: Logic measurement N/A
Selectable for each channel (AC voltage, DC voltage, AC current, DC
current)
Selectable for each channels on measurement mode
• AC voltage: 100 V, 200 V system (400 V, 600 V system using the
Differential Probe)
• AC current: 10 A to 5000 A rms f.s., 10 mA rms f.s. to (depending on
Input ranges
the current sensor in use)
• DC voltage: 100 mV to 500 V f.s. (500 V to 2000 V f.s. using the
Differential Probe)
• DC current: 10 A to 2000 A f.s. (depending on the current sensor in use)
RMS accuracy
±3.0 % f.s. (after zero-adjustment, add current sensor accuracy in use)
Recording interval
1 ms to 1 minutes in 16 stages, Sampling period: 200 μs fixed (AC
voltage / AC current: 1000 RMS data/second)
Envelope mode: always ON
Note: Record maximum/minimum value pairs each recording interval
Recording time
10,000 div
Note: If recording stops before 10,000 div is reached, only the data up to
that point can be displayed and saved.
Other functions
Time axis zoom/compression: 100 ms to 1 days/div
Numerical calculation N/A
Repeating
functions
Single / Repeat selectable
Note: external trigger terminal cannot use
n Recording Time to internal memory using RMS recorder mode (abridged)
• If you set automatic saving to the CF card, data is saved simultaneously with measurement at all times.
• The possible length of a single measurement/recording is the applicable time given below.
• The internal memory capacity is 4 MB/channel. Media capacity depends on the card (for example, 512 MB).
Recording interval
Sampling period
Recording length 10,000 div Max.
1 div = pair of (Max. / Min.) data × 100
1 ms
200 μs
16min 40s
10 ms
200 μs
2h 46min 40s
100 ms
200 μs
1d 3h 46min 40s
1s
200 μs
11d 13h 46min 40s
115d 17h 46min 40s
10 s
200 μs
30 s
200 μs
347d 5h 20min 0s
1 min
200 μs
694d 10h 40min 0s
7
Other functions
Convenient
functionality
■Options specifications (Sold separately)
Setup Wizard – guides you through the settings.
Waveform monitor – lets you make settings while waveforms are
displayed, and reflects the changes on the display in real time.
Automatic saving of measurement data to CF card
Saving to external
memory
Note: In the 50-ms/div-and-slower time axis range, binary-format waveform
data is saved simultaneously with measurement, shortening the dead time
due to writing.
Updating save possible (old files are deleted as new files are saved)
Cursor readout
function
Scaling
functionality
Other functions
Readouts of potential at A/B cursor position, time since triggering,
time difference and potential difference between A and B cursor
positions, and frequencies at their positions
Settable for individual channels
• Memory recorder: OFF, model setting, conversion ratio setting,
2-point setting method
• RMS value recorder: For voltage: OFF, model setting. For current:
sensor model setting.
Comment entry, screen capture, gauges, start condition
preservation, auto setup, waveform scrolling (possible during
measurement)
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 30 cm
(0.98 ft), approx. 150 g (5.3 oz)
Note: The unit-side plug of the 9320-01 is different from the 9320.
LOGIC PROBE 9320-01
Function
Detection of voltage signal or relay contact signal for High/Low state recording
4 channels (common ground between unit and channels), digital/contact input,
switchable (contact input can detect open-collector signals)
Input resistance: 1 MΩ (with digital input, 0 to +5 V)
Input
500 kΩ or more (with digital input, +5 to +50V)
Pull-up resistance: 2 kΩ (contact input: internally pulled up to +5 V)
Digital input threshold 1.4V/ 2.5V/ 4.0V
1.4 V: 1.5 kΩ or higher (open) and 500 Ω or lower (short)
Contact input
2.5 V: 3.5 kΩ or higher (open) and 1.5 kΩ or lower (short)
detection resistance
4.0 V: 25 kΩ or higher (open) and 8 kΩ or lower (short)
500 ns or lower
Response speed
0
to +50 V DC (the maximum voltage that can be applied across input pins without
Max. allowable input damage)
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 1 m
(3.28 ft), approx. 320 g (11.3 oz)
Note: The unit-side plug of the MR9321-01 is different from the MR9321.
LOGIC PROBE MR9321-01
Function
■Software specifications (Bundled accessory)
Wave Processor Program for the 8870 (Bundled accessory)
Supported measureMR8870-20, 8870-20
ment instruments
Operating environ- Computer running under Windows 8/7 (32-bit/64bit), Vista (32bit), XP , or Windows 2000
ment
Loadable data format: Memory function data (MEM extension) of the
MR8870-20/ 8870-20
Max. loadable file size: The maximum size that can be stored by the
MR8870-20/ 8870-20 (subject to the capacity of the PC’s operating
File loading
environment)
Waveform Composite Function: Composite the waveforms of up to 8
HiCorders (16 analog channels)
Overwrites saved scaling and title/channel comments
Overwriting save
Slide show display Sequentially displays waveform files in the same folder
Text conversion
Data conversion format: Select from CSV, tab-separated or spaceseparated
Object data range: Whole range, or between cursors
Data thinning: Available by specifying interval
Conversion methods: Analog waveform data to voltage values, logic
data is converted to ones and zeros
Conversion channels: selectable
Header contents: Title, trigger date, timebase, comments, per-channel
setting conditions
Batch conversion: specify multiple files for batch conversion
Displaying
Display language: English or Japanese (select during installation)
Waveform display: Scroll and magnify/reduce the time axis of the displayed waveform data image, move the zero position of each channel,
zoom and set the vertical axis of each channel independently (variable gain)
Numerical value display: included
Cursor functions: Manipulate A and B cursors independently, and display time and voltage numerically.
Max. displayable channels: 16 analog and 32 logic channels
Gauge display: Time gauge (absolute or relative time, seconds, data
points), voltage gauge (for each channel)
Figure annotations: Text boxes, straight lines, arrows, circles and rectangles at any location
Screen capture: Extended meta format, bitmap format
Search functions: Date, maximum, minimum, level and window search
Template function: Save and reload waveform file display configurations
Printing
Printer support: Color and monochrome printing on printers supported
by the operating system
Printable ranges: All data, screen capture and specifiable areas
Print formats: Undivided, 2, 4, 8 divisions, 2, 4, 8 or 16 traces, 1, 2 or
4 XY screen, gauges, channel comments, zero-position comments,
and A/B cursor values
Print preview and waveform screen hard copy/logging print functions
are included
Detection of AC or DC relay drive signal for High/Low state recording
Can also be used for power line interruption detection
4 channels (isolated between unit and channels), HIGH/LOW range switching
Input resistance: 100 kΩ or higher (HIGH range), 30 kΩ or higher (LOW range)
170 to 250 V AC, ±DC 70 to 250 V (HIGH range)
Output (H) detection
60 to 150 V AC, ±DC 20 to 150 V (LOW range)
0 to 30 V AC, ±DC 0 to 43 V (HIGH range)
Output (L) detection
0 to 10 V AC, ±DC 0 to 15 V (LOW range)
Input
Response time
Rising edge 1 ms max., falling edge 3 ms max. (with HIGH range at 200 V
Max. allowable input
250 Vrms (HIGH range), 150 Vrms (LOW range) (the maximum voltage that can
DC, LOW range at 100 V DC)
be applied across input pins without damage)
Cable length and mass: Main unit cable 1.3 m (4.27 ft), input section cable 46 cm
(1.51 ft), approx. 350 g (12.3 oz)
DIFFERENTIAL PROBE 9322
(Accuracy guaranteed for 1 year)
For high-voltage floating measurement, power line surge noise
Functions
detection, RMS rectified output measurement
For waveform monitor output,
Frequency characteristics: DC to 10 MHz (±3 dB),
DC mode
Amplitude accuracy: ±1 % of full scale (at max. 1000 V DC), ±3% of full
scale (at max. 2000 V DC) (full scale: 2000 V DC)
For detection of power line surge noise,
AC mode
Frequency characteristics: 1 kHz to 10 MHz ±3 dB
DC/AC voltage RMS output detection,
Frequency characteristics: DC, 40 Hz to 100 kHz,
RMS mode
Response speed: 200 ms or less (400 V AC), accuracy: ±1 % of full scale
(DC, 40 Hz to 1 kHz), ±4 % of full scale (1 kHz to 100 kHz) (full scale: 1000 V AC)
Input type: balanced differential input,
Input impedance/capacitance: H-L 9 MΩ/10 pF, H/L-unit 4.5 MΩ/20 pF,
Max. rated voltage to earth: when using grabber clip 1500V AC/DC (CAT II),
Input
600 V AC/DC (CAT III), when using alligator clip: 1000 V AC/DC (CAT II),
600 V AC/DC (CAT III)
Max. allowable input 2000 V DC, 1000 V AC (CAT II), 600 V AC/DC (CAT III)
Voltage divider for 1/1000 of input,
Output
BNC connectors (output switchable for 3 modes DC, AC, RMS)
Power source
Use the AC Adapter 9418-15, (power cannot be supplied from the logic
terminals of the MR8870)
Cable length and mass: 70 cm (2.30 ft), Output side: 1.5 m (4.92 ft), 170g (6.0 oz)
DIFFERENTIAL PROBE P9000
(Accuracy guaranteed for 1 year, Post-adjustment accuracy
guaranteed for 1 year)
P9000-01: For waveform monitor output, Frequency properties: DC to 100 kHz
-3 dB
Measurement modes P9000-02: Switches between waveform monitor output/AC effective value output
Wave mode frequency properties: DC to 100 kHz -3 dB, RMS mode frequency
properties: 30 Hz to 10 kHz, Response time: Rise 300 ms, Fall 600 ms
Switches between 1000:1, 100:1
Division ratio
DC output accuracy ±0.5 % f.s. (f.s. = 1.0 V, division ratio 1000:1), (f.s. = 3.5 V, division ratio 100:1)
Effective value mea- ±1 % f.s. (30 Hz to less than 1 kHz, sine wave), ±3 % f.s. (1 kHz to 10 kHz,
sine wave)
surement accuracy
Input resistance/capacity H-L: 10.5 MΩ, 5 pF or less (at 100 kHz)
Maximum input voltage 1000 V AC, DC
Maximum rated volt1000 V AC, DC (CAT III)
age to ground
Operating
-40°C to 80°C (-40°F to 176°F)
temperature range
(1) AC adapter Z1008 (100 to 240 V AC, 50/60 Hz), 6 VA (including AC
adapter), 0.9 VA (main unit only)
Power supply
(2) USB bus power (5 V DC, USB-microB terminal), 0.8 VA
(3) External power source 2.7 V to 15 V DC, 1 VA
Instruction manual ×1, Alligator clip ×2, Carrying case ×1
Accessories
MR8870 Options in Detail
*Voltage is limited to the specifications of the iput section
Up to 200 A (High precision)
ALLIGATOR CLIP L9790-01
Recommended
Input cable (A)
High-Precision pull-through current sensors, observe waveforms
from DC to distorted AC
AC/DC CURRENT SENSOR CT6862, 1 MHz band width, 50 A
AC/DC CURRENT SENSOR CT6863, 500 kHz band width,
200 A
Observe waveforms from DC to distorted AC
AC/DC CURRENT PROBE CT6841, 1 MHz band width, 20 A
AC/DC CURRENT PROBE CT6843, 500 kHz band width, 200 A
Red/black set attaches to the ends
of the cables L9790
CONTACT PIN 9790-03
Red/black set attaches to the ends
of the cables L9790
CONNECTION CORD L9790
GRABBER CLIP 9790-02
Flexible φ 4.1 mm (0.16 in) thin
dia., cable allowing for up to 600
V input. 1.8 m (5.91 ft) length
* The end clip is sold separately.
Red/black set attaches to the ends
of the cables L9790
* When this clip is attached to the end of the
L9790, input is limited to CAT II 300 V.
Red/black set.
Observe waveforms of distorted AC (cannot for DC)
CLAMP ON SENSOR 9272-10, 100 kHz band width, 200 A
Model : MEMORY HiCORDER MR8870
L9790
9790-03
L9790-01
9790-02
*Voltage is limited to the specifications of the iput section
CONNECTION CORD L9198
Input cable (B)
φ 5.0 mm (0.20 in) dia., cable allowing
for up to 300 V input. 1.7 m (5.58 ft)
length, small alligator clip
Model Name
(Order Code) (Note)
Up to 1000 A (High precision)
High-Precision pull-through current sensors, observe waveforms
from DC to distorted AC
AC/DC CURRENT SENSOR 9709, 100 kHz band width, 500 A
MR8870-20 (2ch, English model)
*Test leads are not included. Purchase the leads appropriate
for your application separately
Observe waveforms from DC to distorted AC
AC/DC CURRENT PROBE CT6844, 200 kHz band width,
500 A
AC/DC CURRENT PROBE CT6845, 100 kHz band width,
500 A
AC/DC CURRENT PROBE CT6846, 20 kHz band width,
1000 A
CONNECTION CORD L9197
Power supply
SENSOR UNIT 9555-10
φ 5.0 mm (0.20 in) dia., cable allowing GRABBER CLIP 9243
for up to 600 V input. 1.8 m (5.91 ft) Attaches to the tip of the banana
length, a detachable large alligator plug cable, CAT III 1000 V, 196
mm (7.72 in) length
clips are bundled
Power supply for the Current Sensor, used alone
CONNECTION CORD L9217
Cord has insulated BNC connectors at both ends,
signal output use, 1.6 m (5.25 ft) length
*Voltage to ground is within this product's specifications.
Separate power source is also required.
DIFFERENTIAL PROBE DIFFERENTIAL PROBE AC ADAPTER
Z1008
P9000-01
P9000-02
Waveform only, up to 1 kV AC/ Waveform/RMS value switch- 100 to 240 V AC
DC, band width up to 100kHz
able, up to 1 kV AC/DC, band
width up to 100kHz
Custom cable
*For P9000. Inquire with your Hioki distributor.
(1) Bus powered USB cable
(2) USB(A)- Micro B cable
(3) 3-prong cable
Storage media
Input cable (D)
14
100 A to 2000 A (Medium speed) A
AC/DC CURRENT SENSOR CT7631, (Auto zero
CT7731)
PC CARD 2G 9830
AC/DC CURRENT SENSOR CT7636, (Auto zero
CT7736)
Use only PC Cards sold by HIOKI. Compatibility and performance
are not guaranteed for PC cards made by other manufacturers. You
may be unable to read from or save data to such cards.
DC, 1 Hz to 10 kHz (-3dB), 100 A, 1 mV/A output
DC, 1 Hz to 10 kHz (-3dB), 600 A, 1 mV/A output
(2 GB)
(1 GB)
AC/DC CURRENT SENSOR CT7642, (Auto zero
CT7742)
(512 MB)
DISPLAY UNIT CM7290
PC CARD 1G 9729
PC CARD 512M 9728
DC, 1 Hz to 10 kHz (-3dB), 2000 A, 1 mV/A output
Power supply for the CT7600/7700 series single drive, Measure,
Display, Signal output function
*Z1005 is a bundled accessory
DIFFERENTIAL PROBE 9322
For up to 1kV AC or 2kV DC,
frequency band width up to 10MHz
AC ADAPTER 9418-15
Power supply
Input cable (E)
*Voltage to ground is within this product's specifications.
Separate power source is also required.
100 to 240 V AC.
500 A to 5000 A *For commercial power lines, 50/60 Hz
CLAMP ON PROBE 9018-50
BATTERY PACK 9780
NiMH, Charges while
installed in the main unit
Good phase characteristics, Frequency characteristics: 40
Hz to 3 kHz, 10 to 500 A AC range, output 0.2 V AC f.s.
AC ADAPTER Z1005
CLAMP ON PROBE 9132-50
100 to 240 V AC
Frequency characteristics: 40 Hz to 1 kHz, 20 to 1000 A
AC range, output 0.2 V AC f.s.
AC FLEXIBLE CURRENT SENSOR CT9667-01/-02/-03
*The 9809 is a bundled accessory
10 Hz to 20 kHz, 5000 A/ 500 A AC, 500 mV/f.s. output,
φ 100 to 254 mm (3.94 to 10.00 in), 3 loop diameters
* Only the small terminal types can be used. * The 9323 is not required for
the small-terminal types 9327, 9320-01, 9321-01 and MR9321-01.
LOGIC PROBE MR9321-01
4-channel type, for voltage/contact signal 4 isolated channels, ON/OFF
ON/OFF detection (response pulse width detection of AC/DC voltage
500 ns or more, miniature terminal type) (miniature terminal type)
CONVERSION CABLE 9323
*Used for connecting the
9320/9321/MR9321 and the 9324
to the Memory HiCorder with
small logic terminal models
Leak Current *For commercial power lines, 50/60 Hz
PROTECTION SHEET 9809
Other options
Logic signal measurement
LOGIC PROBE 9320-01
*The CF card includes a PC card adapter.
* PC Card Precaution
For LCD protection, pairs of
additional sheets
CLAMP ON LEAK HiTESTER 3283
CARRYING CASE 9782
Includes compartment for
options, resin-coated
SOFT CASE 9812
Includes space for small
items, neoprene rubber
CONNECTION
CORD L9217
Cord has insulated
BNC connectors at both
ends, 1.6 m (5.25 ft)
length
10 mA range/10 μA resolution to 200 A range, with
monitor/analog output 1 V f.s.
OUTPUT CORD 9094
3.5 mm (0.14 in) dia. mini plug to banana, 1.5 m (4.92
ft) length
CONVERSION ADAPTER 9199
Receiving side banana, output BNC terminal
AC ADAPTER 9445-02
For USA, 100 to 240 V AC, 9 V/ 1 A
AC ADAPTER 9445-03
For EU 100 to 240 V AC, 9 V/ 1 A
Note: Company names and Product names appearing in this catalog are trademarks or registered trademarks of various companies.
HIOKI (Shanghai) SALES & TRADING CO., LTD.
TEL +86-21-63910090 FAX +86-21-63910360
http://www.hioki.cn / E-mail: [email protected]
DISTRIBUTED BY
HIOKI INDIA PRIVATE LIMITED
TEL +91-124-6590210
HEADQUARTERS
E-mail: [email protected]
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 FAX +81-268-28-0568
HIOKI SINGAPORE PTE. LTD.
http://www.hioki.com / E-mail: [email protected] TEL +65-6634-7677 FAX +65-6634-7477
E-mail: [email protected]
HIOKI USA CORPORATION
HIOKI KOREA CO., LTD.
TEL +1-609-409-9109 FAX +1-609-409-9108
TEL +82-2-2183-8847 FAX +82-2-2183-3360
http://www.hiokiusa.com / E-mail: [email protected] E-mail: [email protected]
All information correct as of Feb. 12, 2016. All specifications are subject to change without notice.
MR8870E5-62M
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement