BENDIX | TCH-003-049A | User's Manual | BENDIX TCH-003-049A User's Manual

Technical Bulletin
Bulletin No: TCH-003-049
Subject:
Effective Date: 10/18/05
Cancels: N/A
Page: 1 of 4
Flood Damage: Bendix Recommended Procedure for Power Vehicles
that may have been Submerged.
This Bulletin provides a recommended procedure for the inspection and (where possible) reconditioning of the air
brake control system components on power vehicles (Trucks, Tractors, and Buses) that have been submerged
in flood waters. See Bulletin TCH-003-048 for Trailer and Dolly recommended inspections.
CAUTION: Take all appropriate safety measures when working in conditions where hazardous
waste, etc. may be present, including appropriate eye protection, gloves and masks. See the General
Precautions section at the end of this Bulletin for recommended standard maintenance safety practices for
normal conditions.
SALT (SEA) WATER IMMERSION
Bendix Commercial Vehicle Systems LLC recommends immediate replacement of
all power vehicle pneumatic air brake valves that have been submerged in salt (sea)
water to avoid any immediate or future operational issues as a result of internal corrosion.
Due to the extremely corrosive nature of salt water and the inherent removal of valve
lubrication, sudden and premature valve malfunction can result. Vehicle components
recommended to be replaced include air compressors, reservoir(s), relay valves, spring
brake valves, ABS relay-modulators and brake actuators. If the air brake components
are being replaced, there is no need to conduct the Air Brake System Inspections below,
instead go to the sections for ABS System inspections and also the “General” heading
for steps in restoring the vehicle to service.
AIR BRAKE SYSTEM INSPECTION
In all other cases where the power vehicle or
components have been submerged in fresh water,
the recommended steps depend upon what is found
during the following inspections. If the vehicle was in a
coastal area and you are not certain whether the water
submergence was by fresh water or salt (sea) water,
our recommendation is to follow the guidelines for salt
water submergence above. A separate section in this
Bulletin covers inspections for the ABS system.
While it is not the scope of this Bulletin to address
anything beyond the air brake control system of
the power vehicle, as a useful first step, Bendix
Commercial Vehicle Systems LLC recommends that
a thorough power-washing of the power vehicle,
including the foundation brakes, will assist the
technician in determining the condition of the vehicle
components. Follow usual chassis re-lubrication
measures (including re-greasing of slack adjusters)
after power-washing.
To check for evidence of water or contamination,
mark and remove the connectors at the first valve in
the system from the front. Inspect the valve for water
and contaminants. Carefully use air pressure to blow
air through the hoses and watch for evidence of water
or contamination. CAUTION: Take all necessary
precautions for safety of the technician and others
in the work area during this procedure, including
use of appropriate eye protection.
If evidence of water or contamination is found, go
to Section A below.
Continue to inspect all the valves in the air brake
system, removing one control (or supply in the case of
quick release valves) and delivery hose from each of
the valves and inspect to determine if there is evidence
of water or contamination. If evidence of water or
contamination is found, follow the instructions
under Section A.
If no evidence of water or contamination is found in
any of the valves or hoses, follow the braking system
inspections shown in Section B.
continued over
Bulletin No: TCH-003-049
Effective Date: 10/18/05
Cancels: N/A
Page: 2 of 4
Section A. Power vehicle air brake systems
with evidence of water or contamination
heater for operation for models where it is not part of
the purge valve assembly and replace as needed.
Once water or contamination has entered into any
of the air brake components (for example through
the exhaust valves, etc.), removal of all the water or
contamination is not possible without total disassembly
of the components. Therefore Bendix recommends
that all pneumatic air brake components be
replaced (including the air compressor, air dryer,
reservoir(s), relay valves, spring brake valves, ABS
relay-modulators, tractor protection valves and brake
actuators). This action is necessary to avoid any
immediate or future operational issues as a result of
internal corrosion and water migration.
For ABS system checks, see “ABS Systems” section
below. Vehicles with normally-functioning air brake
systems can be returned to service. Have all air dryers
regularly serviced to aid in removing any residual
moisture from the vehicle air brake system.
See the “ABS Systems” section below for ABS system
checks and the “General” subheading below for hose
cleaning/replacement recommendations.
Section B. Power vehicle air brake system
with no evidence of water/contaminants
found.
Power vehicles with only limited exterior exposure to
fresh water can be returned to service after having
their air brake system thoroughly tested. Include
checks to verify that the parking and emergency
brakes apply and release and that the reservoirs
charge with minimal leakage (See General section
at the end of this Bulletin for details of a leakage
test). Check that the application and release of the
power vehicle service and parking brakes occur with
no perceptible lag through the full range of normal
service brake applications. Where applicable (for
towing vehicles), make certain that the trailer supply
and trailer service glad hands apply and release the
trailer brakes fully with no perceptible lag.
In addition, all reservoirs should be pressurized and
then slowly drained using their drain valves to remove
any contents. After 30 days retest the vehicle (see
next section).
30 DAY RETEST
Bendix recommends that power vehicles that
do not show any internal evidence of water or
contamination be retested 30 days after the vehicle
has been returned to service. Bendix recommends
that the vehicle be re-tested for operation, leakage,
and contamination, and that a diagnostic check
of the ABS system be carried out (see below).
Use diagnostic software (e.g. Bendix ® ACom5 ™
PC-Diagnostic Software) to look for any present or
intermittent trouble codes stored in the ABS ECU.
Any air brake components found inoperative should
be replaced.
ABS SYSTEMS
ABS systems on power vehicles are comprised of
an ABS wire harness, wheel speed sensors, and an
Electronic Control Unit (ECU) — in some cases with
an attached relay/modulator valve assembly (see
above for air brake valve inspections).
With a parked vehicle (chocked wheels), test the
Tractor Protection function by disconnecting the
service glad hand. Caution: Have a technician hold
the tractor service glad hand to prevent damage
as a result of the test - since it may whip. With the
red Trailer Air Supply button in, make a service brake
application. The tractor protection function should
detect that the glad hand is unattached, and pop the
red button out, protecting the tractor from further air
loss through the glad hand.
FRAME-MOUNT
ECUS
Replace any non-functioning valves.
Following the thorough cleaning of the air dryer it
is recommended to service the unit by replacing
the purge valve assembly and desiccant cartridge
irrespective of the level of contamination found, as long
as the housing is not physically damaged. Check the
CAB-MOUNT
ECU
FIGURE 1 - EXAMPLES OF BENDIX FRAME AND CABMOUNT ECUS
Bulletin No: TCH-003-049
Effective Date: 10/18/05
ABS System Physical Inspection. Inspect ABS
harnesses for damage, cuts, chafing, etc. and replace
as necessary (Bendix does not recommend repairing
or splicing harnesses).
Since the action of floodwaters and power-washing
may move the ABS wheel speed sensors from their
normal position close to the exciter (tone) ring, push
(by hand) each of the wheel speed sensors until
they contact the exciter ring. Normal wheel bearing
play will adjust the sensor position when the wheel
turns. When replacing ABS wheel speed sensors,
either because of damage, or as a result of electronic
diagnostic checks (see below), follow carefully the
lubrication and re-installation instructions in the
instruction sheet that is included with the replacement
sensor (or, if available, you may use BW-120-A).
Whenever a wheel speed sensor is removed from its
mounting block, Bendix recommends that the sensor
clip be replaced.
ABS System Electronic Inspection.
One of two types of Bendix ECU styles may be used
on the power vehicle: frame-mount or cab-mount. See
below Figure 1.
All cab-mounted ECUs that have been submerged
must be replaced.
Unless damaged, frame-mounted ECUs are normally
“weatherproof” and are not affected by water or most
types of contamination. Attach the power vehicle to
a towed vehicle and power up the system. Note any
ABS indicator lamp diagnostic codes - verify PLC
communication between the trailer and tractor. As
necessary, use diagnostic software (e.g. Bendix®
ACom5™ PC-Diagnostic Software) to look for any
present or intermittent trouble code history stored in
the ECU. Replace components as necessary.
Cancels: N/A
Page: 3 of 4
If the contamination cannot be removed from an air
line in this manner, replace the air line using SAE
approved materials.
Air Brake System and Accessory Leakage Test
Park the vehicle on level ground and chock the wheels.
Build system pressure to governor cut-out and allow
the pressure to stabilize for one minute.
Step 1: Observe the dash gauges for two additional
minutes without the service brakes applied.
Step 2: Release the parking brakes, and apply the
service brakes. Allow the pressure to stabilize.
Continue holding for two minutes (you may use a
block of wood to hold the pedal in position.) Observe
the dash gauges.
If you see any noticeable decrease of the dash air
gauge readings (i.e. more than 4 psi, plus two psi for
each additional trailer) during either two minute test,
repair the leaks and repeat this test to confirm that
they have been repaired.
For more information, see Bendix air leakage video
BW2322(DVD), BW2324(VHS), or BW2327(CD).
Bendix Technical Assistance Team
For direct telephone technical support, call the Bendix
technical assistance team at:
1-800-AIR-BRAKE (1-800-247-2725-2-1),
Monday through Friday, 8:00 A.M. to 6:00 P.M. EST,
and follow the instructions in the recorded message.
Or, you may e-mail the Bendix technical assistance
team at: techteam@bendix.com.
See BW1396 for further dual circuit brake system
troubleshooting tests.
GENERAL
Bendix recommends that standard operator pretrip inspections to ensure proper air brake system
operation be rigorously performed for all vehicles
potentially impacted by flood conditions.
When replacing pneumatic system components that
have been subjected to flood conditions, Bendix
recommends that all contaminated air hoses be
disconnected and flushed with clean water and blown
out with air pressure to remove contaminants.
CAUTION: Take all necessary precautions for
safety of the technician and others in the work area
during this procedure, including eye protection.
See over for General Precautions.
Bulletin No: TCH-003-049
Effective Date: 10/18/05
General Precautions. WARNING! PLEASE READ
AND FOLLOW THESE INSTRUCTIONS TO
AVOID PERSONAL INJURY OR DEATH:
When working on or around a vehicle, the following
general precautions should be observed at all
times.
1.
2.
3.
4.
Park the vehicle on a level surface, apply the
parking brakes, and always block the wheels.
Always wear safety glasses.
Stop the engine and remove ignition key when
working under or around the vehicle. When
working in the engine compartment, the engine
should be shut off and the ignition key should
be removed. Where circumstances require
that the engine be in operation, EXTREME
CAUTION should be used to prevent personal
injury resulting from contact with moving,
rotating, leaking, heated or electrically charged
components.
Do not attempt to install, remove, disassemble
or assemble a component until you have read
and thoroughly understand the recommended
procedures. Use only the proper tools and
observe all precautions pertaining to use of those
tools.
If the work is being performed on the vehicle’s
air brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure
from all reservoirs before beginning ANY work
on the vehicle. If the vehicle is equipped with
an AD-IS® air dryer system or a dryer reservoir
module, be sure to drain the purge reservoir.
Cancels: N/A
5.
Page: 4 of 4
F o l l o w i n g t h e v e h i c l e m a n u f a c t u r e r ’s
recommended procedures, deactivate the
electrical system in a manner that safely
removes all electrical power from the vehicle.
6. Never exceed manufacturer’s recommended
pressures.
7. Never connect or disconnect a hose or line
containing pressure; it may whip. Never remove
a component or plug unless you are certain all
system pressure has been depleted.
8. Use only genuine Bendix® replacement parts,
components and kits. Replacement hardware,
tubing, hose, fittings, etc. must be of equivalent
size, type and strength as original equipment and
be designed specifically for such applications
and systems.
9. Components with stripped threads or damaged
parts should be replaced rather than repaired.
Do not attempt repairs requiring machining or
welding unless specifically stated and approved
by the vehicle and component manufacturer.
10. Prior to returning the vehicle to service, make
certain all components and systems are restored
to their proper operating condition.
11. For vehicles with Antilock Traction Control
(ATC), the ATC function must be disabled (ATC
indicator lamp should be ON) prior to performing
any vehicle maintenance where one or more
wheels on a drive axle are lifted off the ground
and moving.
©2005 Bendix Commercial Vehicle Systems LLC 10/05. All Rights Reserved. Printed in U.S.A.
Download PDF