luxCONTROL lighting control system DALI sensors DALI

luxCONTROL lighting control system DALI sensors DALI
luxCONTROL lighting control system
DALI sensors
DALI MSensor
Multi-sensor for DALI system
Product description
•Component of the comfortDIM system (DALI standalone)
•With ambient light dependent control and motion detection
•Simple group assignment via rotary switch
•Multiple MSensors possible in a group
•Can be remote controlled
•Lighting control and motion detection can be deactivated
•Individual adjustment of the parameters with configuration software
•Multi-master compatible: Multiple control modules are possible
in a DALI system
•Power supply via DALI line
Fig. 1
Technical data
DALI cable
Current draw
6 mA from DALI
Operating temperature
0 ... +50 °C
Storage temperature
-25 ... +55 °C
Type of protection
IP20
Ø 86
5
Supply via
46
È
Standards, page 4
Wiring diagrams and installation examples, page 4
Fig. 2
Ø 52
Fig. 3
Fig. 4
Data sheet 12/10-538-7
Subject to change without notice.
www.tridonic.com
1
luxCONTROL lighting control system
DALI sensors
Ordering data
Fig.
Mounting
Type
1
Luminaire installation
DALI-MSensor integrated
Article number
86458265
2
Ceiling installation
DALI-MSensor remote ceiling
86458267
3
Box installation
DALI-MSensor in wall
86458268
4
Surface mounting
DALI-MSensor remote surface
86458269
Packaging: 1 pieces/carton
Specific technical data
Type
Detection
Ø of detection range,
mounted at a height of 2.5 m
Extension of the
detection area1
Swivel
design
Swivel
range
Detection
angle
Light measurement at
the sensor head2
Infra-red
control range
DALI-MSensor integrated
5m
–
no
0°
360°
10 – 650 lx
5m
DALI-MSensor remote ceiling
5m
2m
yes
±15°
360°
10 – 650 lx
5m
DALI-MSensor in wall
5m
2m
yes
±15°
360°
10 – 650 lx
5m
DALI-MSensor remote surface
5m
–
no
0°
360°
10 – 650 lx
5m
1 If
mounted at a height of 2.5 m and swivelled through 15 °
2 The
measured value at the sensor head corresponds to approx. 15 to 2000 lux on the surface measured
Data sheet 12/10-538-7
Subject to change without notice.
www.tridonic.com
2
ACCESSORIES
luxCONTROL lighting control system
DALI sensors
IR-SMART Controller
Product description
•Optional infra-red remote control
•Switching on and off (On/Off button)
•Dimming (Up/Down button)
•Activation of automatic lighting control
•Setting the threshold control point (Set button)
Ordering data
Type
Article number
DSI-SMART Controller
86451922
ACCESSORIES
Packaging: 1 pieces/carton
DALI RC
Product description
•Optional infra-red remote control
and programming unit for DALI MSensor
•For programming the operating parameters
of the DALI MSensor
•With wall bracket
•Switching on and off (On/Off button)
•Dimming (Up/Down button)
•Activating automatic lighting control (sun/cloud button)
•Calling up two scenes
•Calling up five fixed light output values
(100, 50, 25, 12 and 6 %)
•Individual adjustment of the button assignments
with configuration software
Ordering data
Type
DALI-RC
Article number
86458263
Packaging: 1 pieces/carton
Data sheet 12/10-538-7
Subject to change without notice.
www.tridonic.com
3
luxCONTROL lighting control system
DALI sensors
The DALI-MSensor is the ideal addition to the comfortDIM series of products as it offers daylight-dependent lighting control, presence detection and remote control.
It has been designed for the following principal applications:
• Individual offices
• Open-plan offices
• Training / presentation rooms
• Corridors, passageways and garages
The DALI-MSensor is designed that it can be used together with the comfortDIM components (e.g. DALI-MC). For this reason the DALI-MSensor can be addressed
and grouped like an ECG, making system configuration easier. The DALI-MSensor needs the DALI address for communication between multiple sensors, and the
group for communication with other DALI controllers. The DALI-MSensor has special group concept. For further information please refer to the DALI MSensor installation instruction.
A maximum of 12 sensors can be operated on one DALI circuit. This restriction is due to the permitted data traffic on the DALI circuit. If the DALI-MSensors operate
independently of each other the maximum number of sensors per DALI circuit is reduced to eight (see DALI MSensor installation instruction).
Wiring
Standards
EN 61547
EN 61347-2-11
EN 55015
L
N
DALI
PS
PCA EXCEL one4all
PCA EXCEL one4all
DALI-MSensor
DALI
GC
DALI
SC
DALI
SCI
Wiring type and cross section
The wiring can be solid wire or stranded wire with a
cross-section of 0.5 mm² to 1.5 mm².
Multiple sensors can be operated on a DALI circuit.
The functions of the sensor can be activated autonomously or
in a network of several sensors.
Installation
• DALI is not SELV.
The installation instructions for mains voltage therefore apply.
• The DALI MSensor must not be connected to the mains. It is supplied directly
via the DALI signal line.
wire preparation:
0.5 – 1.5 mm²
7.5 – 8.5 mm
Remote control
The DALI MSensor can be controlled with 2 remote controls:
•IR smartController
•DALI-RC
IR smartController
DALI-RC
IR sender
ON – Luminaire group ON
UP – Increase light value
DOWN – Reduce light value
Automatic control mode
ON/OFF
SET – saves the current
light control value
OFF – Luminaire group OFF
LED status display
Switch all luminaires in the
DALI system ON or OFF
Light value 100 % brightness
Light value 50 % brightness
Increase or reduce the light value
(dimming the DALI system)
Light value 25 % brightness
Automatic control mode ON
Light value 12 % brightness
Call up scene 2
Light value 6 % brightness
Call up scene 1
Data sheet 12/10-538-7
Subject to change without notice.
IR sender
www.tridonic.com
4
luxCONTROL lighting control system
DALI sensors
Light level recognition area
h
Motion detection
d1
90°
h
70°
h*
d1
d2
1.7 m
2.4 m
3.4 m
2.0 m
2.8 m
4.0 m
2.3 m
3.2 m
4.6 m
2.5 m
3.5 m
5.0 m
2.7 m
3.8 m
5.4 m
3.0 m
4.2 m
6.0 m
3.5 m
4.9 m
7.0 m
4.0 m
5.6 m
8.0 m
d2
* The recommended maximum room height for office applications is 3 m and for corridor applications for example 4 m.
Calculation of the diameter:
d = 2 × tan(0,5 × a) × h
The following operating modes can be set for lighting control via the
MasterCONFIGURATOR configuration software:
The following operating modes can be set for the motion detector via the
MasterCONFIGURATOR configuration software:
Active
Constant light control is active.
Active
Inactive
Constant light control is deactivated. The lighting is switched
on an adjustable light value.
The light is switched on or off automatically depending on
whether or not there is a person in the room.
Off Only
The motion detector only switches the connected lighting
off. The luminaires are switched on manually via the connected external switch or infra-red control.
Never Off
If it has not detected any movement the sensor dims to the
“second light value” parameter and remains at this value
Inactive
The motion sensor is deactivated. The light must be switched on or off manually.
Setpoint adjustment
• DSI-SMART Controller: Pressing the Set button stores the current light value as a new setpoint.
• DALI-RC:
In programming mode with the Automatic button (Icons: sun / moon)
• MasterCONFIGURATOR
Bright-out
If the nominal illuminance (e.g. 500 lux) is exceeded for 10 minutes by more
than 150 % (e.g. 750 lux), the lighting is switched off even if motion is detected.
The lighting is switched on again when the measured light value falls below the
setpoint.
This function can be adjusted via the MasterCONFIGURATOR.
Switch-off delay
This is the time after which the lighting is switched off if no movement is
detected. It can be set via the “ON time” parameter.
Second light value
On the DSI-Smart PTM you can set whether the light is to be switched off after
the switch-off delay or dimmed to the second light value. The light value and the
dwell time (how long the value is held) can be set via the “MIN value” and
“MIN time” parameters.
Manual-off delay
If the system is switched off manually via the switch or remote control the
motion sensor is deactivated. At the end of a delay time if motion has not been
detected the motion sensor is activated again. If the sensor detects motion
during the “Manual Off” delay, the time will be reset to the start.
Data sheet 12/10-538-7
Subject to change without notice.
www.tridonic.com
5
luxCONTROL lighting control system
DALI sensors
2,5 m
Swiveling angle
2m
1m
5m
General settings
Parameter
Motion Detector
Light Regulation
Light Regulation Point
Power On Setting
Bright-out timeout
Bright-out threshold
Control speed
Switch On Level
Rotary Switch
Default Values
Enabled, on/off
Enabled
150 lx
No action
10 min
150 %
4
auto
0, Broadcast
Default Parameter Motion Detector
Default Values
<0,7 s
Regulated
20 min
5,6 s
3 %
10 min
5,6 s
10 min
2
light level
Parameter
1 ON Fading
ON Light Level
2 ON Delay Time
3 MIN Fading
MIN Light Level
4 MIN Delay Time
5 OFF Fading
EXIT Delay Time
motion in the room
1
3
4
5
delay time
Rotary Switch
DALI-Grouping is done with the rotary switch. The rotary switch is at the backside of the DALI-MSensor.
Position
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Luminaire Group
Broadcast
DALI Group 1
DALI Group 2
DALI Group 3
DALI Group 4
DALI Group 5
DALI Group 6
DALI Group 7
DALI Group 8
DALI Group 9
DALI Group 10
DALI Group 11
DALI Group 12
DALI Group 13
DALI Group 14
DALI Group 15
Sensor Input Group
DALI Group 1
DALI Group 2
DALI Group 3
DALI Group 4
DALI Group 5
DALI Group 6
DALI Group 7
DALI Group 8
DALI Group 9
DALI Group 10
DALI Group 11
DALI Group 12
DALI Group 13
DALI Group 14
DALI Group 15
DALI Group 16
Data sheet 12/10-538-7
Subject to change without notice.
www.tridonic.com
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement