Catalogue 2011 790 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications Photo on title page: We are represented at many trade shows to advice you about our wide product portfolio. Further information: www.kathrein.de Catalogue Issue 01/2011 All data published in previous catalog issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding datas please check valid data sheets! Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4 and thereby respects the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. Calculation of Wind Loading on Kathrein Base Station Antennas In 1998 the co-ordinating committee of the Standardisation Group for Building Standards decided that during the harmonisation process of European standards, the DIN-Standards shall be modified and republished based on the European Pre-Standards. As a result of this harmonisation process the new edition of DIN 1055 Part 4 was finally published in 2005. This standard defines the worst case loading example created by natural wind forces on bearing structures and their individual elements. The standard thereby defines the principles for calculating the maximum loading and for confirming the bearing capacity of structures in general. One of the major changes in the calculation of the wind load under DIN 1055-4 is the definition of the value cf0. Due to these changes in the calculation formula within the standard, the calculated wind load of some Base Station Antennas is higher than previously specified on earlier data sheets. During 2009 Kathrein will migrate to calculating and specifying all wind loads in accordance with DIN 1055-4 (similar to the European Standard EN 1991-1-4) on the online data sheets. If the wind load has been calculated under the updated standard then this will be explicitly mentioned on the data sheet. The physical dimensions of our products have not been modified unless otherwise specified, nor has the actual wind loading surface area of the antennas increased in any way. “Quality leads the way” As the world’s oldest and largest antenna manufacturer, we live up to claim “Quality leads the way” on a daily basis. One of the fundamental principies is to always be on the lookout for the best solution for our customers. Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001. Internet: www.kathrein.de KATHREIN-Werke KG . Phone +49 80 31 184-0 . Fax +49 80 31 184-973 Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . D-83004 Rosenheim . Germany General Information The catalogue is splitted into two parts. Part 1: Antennas Part 2: Filters, Combiners and Amplifiers Pages Antennas Filters, Combiners, Amplifiers 7 – 202 203 – 316 3 Subsidiaries/Affiliates A current list of Kathrein’s International Representatives can be found on our homepage www.kathrein.de Please contact for Sales queries, orders, catalogues or CD-ROM: Fax: +49 80 31 184-820 E-Mail: [email protected] Technical Information: Fax: +49 80 31 184-973 E-Mail: [email protected] 4 List of available Catalogues for Mobile Communication Antennas and Accessories Catalogue 2011 790 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications 790 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications 27 – 512 MHz KATHREIN-Antennas and Antenna Line Products For Public Safety, Ports, Airports, Distribution, Public Transport, Utilities 27 – 512 MHz KATHREIN-Antennas and Antenna Line Products Professional Antennas, Filters, Combiners and Multicouplers for Ground-to-Air Communications Antennas for Trains and Buses KATHREIN KATHREIN Antennas and Antenna Line Products for Mobile Communications The listed catalogues are also available on CD-ROM Mobilfunkantennen und Zubehör ition 01 15, Ed Version -1608 81 No.: 99 /11 Antennen • Electronic Subject to alteration 5 Part 1: Antennas for Mobile Communications 6 698 – 894 MHz 1710 – 2170 MHz XPol XXPol Dual-band 790 … 960 MHz XPol 790 … 960 MHz XXPol 790 … 960 MHz 1710 … 2170 MHz VPol 1710 … 2690 MHz XPol 1710 … 2690 MHz XXPol 2-Multi-band 790 … 960 MHz 1710 … 2690 MHz XXPol Dual-band 790 … 960 MHz 1710 … 2690 MHz XXXPol Omni VPol Indoor VPol, VXPol, VHPol RET Electrical Accessories Mechanical Accessories Remote Electrical Tilt-System Splitters, Tappers and Measurement Tools Clamps, Downtilt Kits, ... 7 Summary of Antenna Types The articles are listed by type number in numerical order. New or changed product. Type No. Page 730... Type No. Page 737... Page Type No. Page 741989V01 76 742351V01 60 741990V01 77 742352V01 94 730368 52 737398 199 730376V01 53 737971 190 730378V01 54 737972 190 742... 730382 55 737973 190 742033 193 800100.. 730677 52 737974 190 742034 193 80010046 730691 53 737975 190 742047V01 106 737977 190 742113 195 737978 190 742186V01 73 800101.. 742192V01 51 80010111 137 742196V01 64 80010121V01 110 731... 731651 188 738... 732... 57 738187 138 742210V01 63 80010122V01 111 112 732317 189 738192 132 742213V01 71 80010123V03 732318 189 738440 201 742214V01 67 80010141 26 732321 189 738445 50 742215V01 68 80010147 153 732322 189 738446 50 742218V01 62 732327 189 738449 151 742219V01 62 738450 128 742222V01 98 738546 188 742223V02 100 80010202V02 29 738908 198 742224V02 104 80010203V02 30 742225V02 109 80010204V02 32 742226V01 97 80010207V01 29 734... 800102.. 734360 197 734361 197 739... 734362 197 739489V01 63 742233V01 86 80010208V01 33 734363 197 739619 28 742235V01 92 80010214V01 34 734364 197 739620 28 742236V01 89 80010215V01 33 734365 197 739710 76 742237 88 80010217V01 37 742263 193 80010218V01 37 742264V02 99 80010247V01 64 735... 735727 741... 48 736... 8 Type No. 741322 101 742265V02 102 80010249 741327 101 742266V02 107 80010251V01 741573 148 742270V03 115 80010274 136 147 60 736347 133 741623 61 742271V03 118 80010290V01 117 736349 134 741790 139 742272V03 122 80010291V02 120 736350 131 741984V01 75 742290 57 80010292V02 124 736854 54 741988V01 75 742317 193 80010294V02 31 Summary of Antenna Types The articles are listed by type number in numerical order. New or changed product. Type No. Page 800103.. Type No. Page Type No. Page Type No. Page 80010511V01 93 80010736 20 86010046 161 80010300V01 38 80010516V01 42 80010747 135 86010100 170 80010303V02 30 80010517V01 44 80010748 145 86010101 170 80010305V02 32 80010518V01 45 80010749 146 86010102 170 80010306V02 34 80010764 21 86010103 170 80010307V01 35 800106.. 80010765 22 86010104 170 80010308V01 36 80010605 78 80010766 23 86010105 170 80010309V01 36 80010606V01 79 86010130 168 80010310V01 38 80010614V01 68 850… 86010131 168 80010314 80 80010618 80 85010002 188 86010136 171 80010360 82 80010621V01 70 85010003 188 86010137 171 80010368 56 80010622 90 85010005 202 86010138 171 80010375 81 80010634V01 31 85010006 196 86010140 160 80010378 74 80010636 73 85010008 191 86010141 160 80010644 88 85010010 83 86010147 158 80010643 26 85010014 192 86010148 158 800104.. 80010425V01 66 80010647V01 43 85010015 192 86010150 172 80010426V01 66 80010658 49 85010016 192 86010151 172 80010428V01 67 80010665 105 85010017 192 86010152 172 80010430 149 80010667 40 85010058 193 80010431 152 80010668 41 85010059 193 K61... 80010433 143 80010670V01 116 85010060 194 K61335 74 80010671V01 119 85010061 194 140 80010672V01 123 80010439V01 80010442 200 K63... 80010454V01 96 80010675 126 860… 80010456V02 27 80010677 144 86010002 163 80010465 142 80010681 65 86010006 159 K75... 80010485V01 103 80010682 87 86010007 162 K751161 129 80010486V01 108 80010692 121 86010017 169 K7515641 130 80010492V01 125 80010698 114 86010018 169 86010019 169 86010023 173 800105.. 800107.. K63236001 80010504V01 69 80010709 150 86010026 159 80010505V01 72 80010734 18 86010030 164 80010510V01 91 80010735 19 86010031 165 173 9 Antenna Designs: Antenna Families Harmony of Design and Technology Omni XPol Panel Triple-band XPol Panel 800/900 XPol Panel 1800/2000/2600 10 VPol Panel 800/900 Directional Antenna Designs: Special Directional Antennas For Particular Applications Antennas for The distinguishing features of these special versions, e.g. parabolic panels or log. periodic antennas, are: – tunnel use – very small half-power beam width (high gain) – railway use – high sidelobe suppression – micro cells (street use) – also Dual-band and Multi-band versions – high gain link for repeaters – bidirectional horizontal pattern. BiDir Dual-Beam Panel LogPer Dual Yagi 11 Antenna Designs: Antenna Families / RET-system Distinguishing features Design Compact size and elegant design are the distinguishing features of Kathrein’s antenna families. Radome The radomes cover the internal antenna components. The fiberglass material guarantees optimum performance with regards to stability, strength, UV resistance, painting and weather protection. Environmental influences Kathrein antenna designs are based on fundamental engineering knowledge and also on our decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Environmental conditions Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regards to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C Impedance Standard Impedance for all products is 50 Ω unless otherwise stated. Great variety of half-power beam width, gain values, electrical downtilt According to the antenna type selected, customer can choose from different half-power beam widths. Gain values up to 22.5 dBi and electrical downtilts up to 15° for panel antennas are available. Downtilts are either fixed or adjustable or even controlled by remote electrical tilt system (RET). Low intermodulation After many years of experience in the construction of antennas and after products (typically –150 dBc) intensive research into the effects of intermodulation, we have been able to optimize the material and technology used for antennas (the given value refers to 3rd order products measured with 2 carriers of 20 W each). Excellent tracking Tracking states the symmetry between the +45° and –45° polarized horizontal pattern. Bad tracking values lead to interferences in the network and reduced diversity performance. Kathreins special Tracking compensation reduces the average value measured at ±60° to < 2 dB. Superior squint Squint, also often referred to as “Pattern Symmetry”, gives the symmetry of the pattern over the whole frequency range measured at the 3 dB points. Interferences and nulls in the network may be the result of bad values. In contrast to the vertical squint which is usually good, excellent squint values of the horizontal pattern are hard to reach. Kathreins superior values of ± 5 % of the half-power beam width are in line with the requirements from system suppliers. Multi-band design Depending on antenna family broad-band, multi-band, dual-band and triple-band versions can be offered. Therefore the varity of antennas used can be kept to a minimum. Excellent grounding The antennas are DC grounded according EN 50083-1. Multi-functional installation hardware Depending on the type, the antennas are equipped with up to 3 attachment points. Panels can be wall-mounted without any additional hardware. For mast-mounting, stainless steel brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories). MTBF Statement Traditionally passive components like antennas cannot be well calculated due to the lack of a sufficient number of components in the MTBF library. Unfortunately this constraint results in a very inaccurate calculation. Thus such results are technically questionable and unrealistic. In essence, antennas are made out of mechnical parts that do not show any failure rates. Only available failure rates can be calculated into an MTBF value. Consequently such components cannot be listed in any MTBF library. Remote Electical Tilt System Kathrein hereby states that RET devices, as far as the functionality and AISG Compliancy features are described within the AISG / 3 GPP standard, are compliant with the standard. 12 Downtilting of Antennas: Downtilt Possibilities Mechanical downtilt For further technical information please see “Mechanical Accessories”, page 186. Electrical downtilt Description of the adjustment mechanism (protective cap removed): 1 1 2 2 ➀ Adjustment wheel with twist-lock function. ➁ Downtilt spindle with integrated scale. ➀ Thread for fixing the protective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0° – max.° max.° – 0° Remove the protective cap. Set downtilt angle by rotating the adjustment wheel. Screw on the protective cap again. Remote Electrical Tilt (RET) For further technical information please see “RET”, pages 156 and 157. 13 Kathrein Antennas Product Description (Type) XXPol Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi 2°–8°T/2°T Polarization(s): (X) Dual +45°/ –45° (V) Vertical Antenna Family Frequency Range(s) Integrated Combiner Horizontal Half-power Beam Width(s) Gain Value(s) Variable / Fixed Electrical Tilt(s) 14 Characteristical Horizontal and Vertical Antenna Patterns Horizontal Patterns: 45° 30° 20° 3 0 dB dB 3 10 10 3 0 20° dB 10 0 30°/33° 45° 120° 90° 120° 65° 180° 215° 10 10 3 0 0 0 60°/65° dB 3 dB 3 dB 10 88°/90° 120° Vertical Patterns: 65° 15° 30° 0 0 0 65° 30° 10° 10 0 10° 15° 4° 6° 3 10 dB 10 dB 3 3 dB 3 10 dB dB 3 10 0 6° 3 dB 10 0 4° 15 16 700/800 XPol 700/1800–2000 XXPol Summary – Directional Antennas Dual Polarization + 45°/ –45° 700/800 XPol / 700/1800–2000 XXPol 700/800 XPol Type XPol Panel iRCU XPol Panel iRCU XPol Panel iRCU 698–894 698–894 698–894 Type No. Height [mm] Connector position Page 65° 65° 65° 15dBi 16dBi 17dBi 0°–16°T 0°–10°T 0°–10°T 80010734 80010735 80010736 1355 1934 2438 bottom bottom bottom 18 19 20 700/1800–2000 XXPol XXPol Panel iRCU 698–894 1710–2170 65° 65° 15dBi 17.5dBi 0°–16°T 0°–10°T 80010764 1403 bottom 21 XXPol Panel iRCU 698–894 1710–2170 65° 65° 16dBi 18.5dBi 0°–10°T 0°–10°T 80010765 1918 bottom 22 XXPol Panel iRCU 698–894 1710–2170 65° 65° 17dBi 18.5dBi 0°–10°T 0°–10°T 80010766 2438 bottom 23 New or changed product iRCU specifications (86010145) see page 24 17 700/800 XPol 700/1800–2000 XXPol Multi-band Panel 698 – 894 X Dual Polarization 65° Half-power Beam Width iRCU Integrated replaceable Remote Control Unit 0°– 16° Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 15dBi 0°–16°T s clamp d e includ 80010734 Type No. Frequency range 698–894 698 – 806 MHz Polarization Gain 824 – 894 MHz +45°, –45° +45°, –45° 12.05 dBd / 14.2 dBi 12.65 dBd / 14.8 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 68° 65° Copolar: > 30 dB Average: 32 dB Copolar: > 30 dB Average: 33 dB Typically: 24 dB > 10 dB, Avg. 15 dB Typically: 23 dB > 10 dB, Avg. 16 dB 16° 14.8° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: 0°– 16°, continuously adjustable 0° ... 8° ... 16° T 16 ... 17 ... 17 dB 19 ... 20 ... 20 dB 0° ... 8° ... 16° T 18 ... 17 ... 16 dB 25 ... 23 ... 23 dB VSWR < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Connector position Wind load Bottom Frontal: 620 N (at 150 km/h) 1550 N (at 150 mph) Lateral: 200 N (at 150 km/h) 500 N (at 150 mph) Rearside: 710 N (at 150 km/h) 1770 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 1355 / 303 / 99 mm (53.3 / 11.9 / 3.9 inches) Category of mounting hardware M (Medium) Weight Scope of supply 11 kg ( 24 lbs) / 13 kg (27 lbs) (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 in iRCU out 8pin 8pin male female 18 698 – 894 +45° 698 – 894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 186 700/800 XPol 700/1800–2000 XXPol Multi-band Panel 698 – 894 X Dual Polarization 65° Half-power Beam Width iRCU Integrated replaceable Remote Control Unit 0°– 10° Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 16dBi 0°–10°T s clamp d e includ 80010735 Type No. Frequency range 698–894 698 – 806 MHz Polarization Gain 824 – 894 MHz +45°, –45° +45°, –45° 13.35 dBd / 15.5 dBi 13.85 dBd / 16 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 67° 65° Copolar: > 30 dB Average: 35 dB Copolar: > 30 dB Average: 35 dB Typically: 25 dB > 11 dB, Avg. 15 dB Typically: 25 dB > 11 dB, Avg. 15 dB 11.3° 10° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 16 ... 17 ... 17 dB 16 ... 19 ... 20 dB 0° ... 5° ... 10° T 18 ... 17 ... 16 dB 20 ... 20 ... 20 dB VSWR < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Connector position Wind load Bottom Frontal: 900 N (at 150 km/h) 2260 N (at 150 mph) Lateral: 310 N (at 150 km/h) 760 N (at 150 mph) Rearside: 1030 N (at 150 km/h) 2580 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 1934 / 303 / 99 mm (76.1 / 11.9 / 3.9 inches) Category of mounting hardware H (Heavy) Weight Scope of supply 13 kg (28.7 lbs) / 15 kg (33 lbs) (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 in iRCU out 8pin 8pin male female 698 – 894 +45° 698 – 894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 186 19 700/800 XPol 700/1800–2000 XXPol Multi-band Panel 698 – 894 X Dual Polarization 65° Half-power Beam Width iRCU Integrated replaceable Remote Control Unit 0°– 10° Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 17dBi 0°–10°T s clamp d e includ 80010736 Type No. Frequency range 698–894 698 – 806 MHz Polarization Gain 824 – 894 MHz +45°, –45° +45°, –45° 14.25 dBd / 16.4 dBi 14.85 dBd / 17 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 67° 65° Copolar: > 30 dB Average: 35 dB Copolar: > 30 dB Average: 35 dB Typically: 25 dB > 11 dB, Avg. 15 dB Typically: 20 dB > 11 dB, Avg. 15 dB 9.5° 8.6° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 16 ... 16 ... 16 dB 19 ... 18 ... 17 dB 0.5° ... 5° ... 9.5° T 18 ... 18 ... 17 dB 20 ... 20 ... 20 dB VSWR < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Connector position Wind load Bottom Frontal: 1160 N (at 150 km/h) 2900 N (at 150 mph) Lateral: 390 N (at 150 km/h) 970 N (at 150 mph) Rearside: 1380 N (at 150 km/h) 3450 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 2438 / 303 / 99 mm (96 / 11.9 / 3.9 inches) Category of mounting hardware H (Heavy) Weight Scope of supply 15 kg (34.4 lbs) / 17 kg (37.4 lbs) (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 in iRCU out 8pin 8pin male female 20 698 – 894 +45° 698 – 894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 186 698 – 894 1710 – 2170 X X 65° 65° iRCU iRCU 0°– 16° 0°– 10° Dual Polarization Half-power Beam Width Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt 700/800 XPol 700/1800–2000 XXPol Multi-band Panel XXPol Panel iRCU 698–894/1710–2170 65°/65° 15/17.5dBi 0°–16°/0°–10°T 80010764 Type No. Frequency range 698–894 698 – 806 MHz 824 – 894 MHz Polarization +45°, –45° Gain s clamp d e includ 1710–2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° +45°, –45° 17.3 dBi 17.5 dBi 12.15 dBd / 14.3 dBi 12.65 dBd / 14.8 dBi Horizontal Pattern: Half-power beam width 68° 65° 61° 60° Copolar: > 30 dB Average: 32 dB Copolar: > 27 dB Average: 30 dB Copolar: > 30 dB Average: 34 dB Copolar: > 30 dB Average: 34 dB Typically: 25 dB > 10 dB, Avg. 15 dB Typically: 25 dB > 8 dB, Avg. 14 dB Typically: 25 dB > 8 dB, Avg. 14 dB Typically: 25 dB > 10 dB, Avg. 16 dB Tracking, Avg. 1.5 dB 1.5 dB 2.0 dB 1.0 dB Squint ±2.5° ±4.0° ±4.0° ±1.5° 15° 613.5° 7.5° 7.5° Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam: Average: 0°– 16°, continuously adjustable 0° ... 8° ... 16° T 17 ... 16 ... 16 dB 19 ... 19 ... 18 dB 0°– 10°, continuously adjustable 0° ... 8° ... 16° T 18 ... 16 ... 16 dB 22 ... 20 ... 20 dB VSWR 0° ... 5° ... 10° T 18 ... 18 ... 17 dB 20 ... 20 ... 20 dB < 1.5 Isolation, between ports Intrasystem: > 30 dB, Intersystem: > 35 dB Intermodulation IM3 Max. power per input 0° ... 5° ... 10° T 18 ... 18 ... 17 dB 20 ... 20 ... 20 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Input 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Connector position Bottom Wind load Frontal: Lateral: Rearside: 690 N (at 150 km/h) 1710 N (at 150 mph) 260 N (at 150 km/h) 640 N (at 150 mph) 710 N (at 150 km/h) 1770 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 1403 / 300 / 152 mm (55.2 / 11.8 / 6 inches) Category of mounting hardware M (Medium) Weight 18.5 kg (40.8 lbs) / 20.5 kg (45.2 lbs) (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 698–894 –45° 1710–2170 –45° 7-16 7-16 long neck iRCU out in iRCU out in 8pin 8pin 8pin 8pin female male female male 698–894 +45° 1710–2170 +45° 7-16 7-16 long neck For more information about additional mounting accessories please refer to page 186 21 700/800 XPol 700/1800–2000 XXPol Multi-band Panel 698 – 894 1710 – 2170 X X 65° 65° iRCU iRCU 0°– 10° 0°– 10° Dual Polarization Half-power Beam Width Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 65°/65° 16/18.5dBi 0°–10°/0°–10°T 80010765 Type No. Frequency range 698–894 698 – 806 MHz 824 – 894 MHz Polarization +45°, –45° Gain s clamp d e includ 1710–2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° 13.15 dBd / 15.3 dBi 13.65 dBd / 15.8 dBi +45°, –45° +45°, –45° 18 dBi 18.5 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 68° 65° 63° 62° Copolar: > 30 dB Average: 34 dB Copolar: > 30 dB Average: 34 dB Copolar: > 27 dB Average: 34 dB Copolar: > 27 dB Average: 34 dB Typically: > 25 dB > 8 dB, Avg. 15 dB Typically: > 30 dB > 10 dB, Avg. 15 dB Typically: > 25 dB Typically: > 20 dB > 10 dB, Avg. 16 dB > 10 dB, Avg. 14 dB Tracking, Avg. 1.0 dB 1.5 dB 1.5 dB 1.0 dB Squint ±2.5° ±3.0° ±3.0° ±2.5° 11.8° 610.8° 5.8° 5.8° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 16 ... 16 ... 18 dB 18 ... 20 ... 20 dB 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 18 ... 18 ... 16 dB 20 ... 22 ... 20 dB VSWR 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB < 1.5 Isolation, between ports Intrasystem: > 30 dB, Intersystem: > 35 dB Intermodulation IM3 Max. power per input 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Input 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Connector position Bottom Wind load Frontal: Lateral: Rearside: 950 N (at 150 km/h) 2380 N (at 150 mph) 360 N (at 150 km/h) 890 N (at 150 mph) 980 N (at 150 km/h) 2460 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 1918 / 300 / 152 mm (75.5 / 11.8 / 6 inches) Category of mounting hardware H (Heavy) Weight 23.5 kg (51.8 lbs) / 25.5 kg (56.2 lbs) (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 1710–2170 1710–2170 –45° +45° 7-16 long neck7-16 8pin male 8pin female 22 in out 8pin female 8pin male For more information about additional mounting accessories please refer to page 186 698 – 894 1710 – 2170 X X 65° 65° iRCU iRCU 0°– 10° 0°– 10° Dual Polarization Half-power Beam Width Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt 700/800 XPol 700/1800–2000 XXPol Multi-band Panel XXPol Panel iRCU 698–894/1710–2170 65°/65° 17/18.5dBi 0°–10°/0°–10°T s clamp d e includ 80010766 Type No. Frequency range 698–894 698 – 806 MHz 824 – 894 MHz Polarization +45°, –45° Gain 1710–2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° 14.25 dBd / 16.4 dBi 14.65 dBd / 16.8 dBi +45°, –45° +45°, –45° 18 dBi 18.5 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 68° 65° 63° 62° Copolar: > 30 dB Average: 34 dB Copolar: > 30 dB Average: 34 dB Copolar: > 27 dB Average: 34 dB Copolar: > 27 dB Average: 34 dB Typically: > 25 dB > 8 dB, Avg. 15 dB Typically: > 30 dB > 10 dB, Avg. 15 dB Typically: > 25 dB Typically: > 20 dB > 10 dB, Avg. 15 dB > 10 dB, Avg. 12 dB Tracking, Avg. 1.0 dB 1.5 dB Squint ±2.5° ±3.0° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: 9.5° 68.7° 5.8° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 16 ... 16 ... 16 dB 18 ... 20 ... 18 dB 0° ... 5° ... 10° T 18 ... 18 ... 16 dB 20 ... 20 ... 20 dB VSWR 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB < 1.5 Isolation, between ports Intrasystem: > 30 dB, Intersystem: > 35 dB Intermodulation IM3 Max. power per input 5.8° 0°– 10°, continuously adjustable < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Input 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Connector position Bottom Wind load Frontal: 1270 N (at 150 km/h) 3170 N (at 150 mph) Lateral: 470 N (at 150 km/h) 1160 N (at 150 mph) Rearside: 1320 N (at 150 km/h) 3310 N (at 150 mph) Max. wind velocity 241 km/h (150 mph) Height/width/depth 2438 / 300 / 152 mm (96 / 11.8 / 6.0 inches) Category of mounting hardware H (Heavy) Weight 26.5 kg (58.3 lbs) / 28.5 kg (62.7 lbs) (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter iRCU specifications (86010145) see page 24 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female in out 1710–2170 1710–2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 186 23 700/800 XPol 700/1800–2000 XXPol Specifications iRCU 86010145 iRCU specifications (86010145) Field replaceable without dismantling the antenna Logical interface ex factory1) AISG 1.1 Protocols Compliant to AISG 1.1 and 3GPP/AISG 2.0 Hardware interface2) 2 x 8pin connector acc. IEC 60130-9; according to AISG: – iRCU in (male): Control / Daisy chain in – iRCU out (female): Daisy chain out Power supply Power consumption Adjustment time (full range) 10 ... 30 V < 1 W (stand by) < 8.5 W (motor activated) 40 sec. Adjustment cycles > 50,000 Certification CE, 3) * See mounting instructions and warnings. 1) The protocol of the logical interface can be switched from AISG 1.1 to 3GPP/AISG 2.0 and vice versa with a vendor specific command. Please note: If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the iRCU must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information. 2) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handtightened’). The connector should be tightened by hand only! 3) Tested to comply with FCC Standards. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 24 For more information about additional mounting accessories please refer to page 186 800/900 XPol Summary – Directional Antennas Dual Polarization + 45°/ –45° 800/900 Dual Polarization + 45°/ –45° Type Type No. Height [mm] 80010141 80010643 80010456V02 1296 2254 2254 XPol Panel XPol Panel XPol Panel 806–960 790–960 790–960 30° 30° 30° 18.5dBi 21dBi 20.5dBi 0°T 0°T 0°–10°T XPol Panel 806–960 65° 9dBi 0°T 739619 XPol Panel 806–960 65° 12.5dBi 0°T XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 65° 65° 65° 15dBi 15dBi 15dBi XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 65° 65° 65° XPol Panel XPol Panel 790–960 790–960 XPol XPol XPol XPol XPol Panel Panel Panel Panel Panel Connector position Page bottom rearside rearside 26 26 27 256 bottom or top 28 739620 656 bottom or top 28 0°T 6°T 0°–14°T 80010202V02 80010207V01 80010303V02 1294 1294 1294 bottom bottom bottom 29 29 30 17dBi 17dBi 16.5dBi 0°T 6°T 0°–10°T 80010203V02 80010294V02 80010634V01 1934 1934 1934 rearside rearside rearside 30 31 31 65° 65° 18dBi 17.5dBi 0°T 0°–8°T 80010204V02 80010305V02 2254 2254 rearside rearside 32 32 790–960 790–960 790–960 790–960 790–960 65° 65° 65° 65° 65° 18dBi 18dBi 18dBi 17.5dBi 18dBi 0°T 6°T 9°T 0°–10°T 0°–10°T 80010215V01 80010208V01 80010214V01 80010306V02 80010307V01 2574 2574 2574 2574 2574 rearside rearside rearside bottom rearside 33 33 34 34 35 XPol Panel 790–960 85° 13.5dBi 0°–14°T 80010308V01 1294 bottom 36 XPol Panel 790–960 85° 15dBi 0°–10°T 80010309V01 1934 bottom 36 XPol XPol XPol XPol 790–960 790–960 790–960 790–960 85° 85° 85° 85° 17dBi 17dBi 16dBi 16.5dBi 0°T 6°T 0°–10°T 0°–10°T 80010217V01 80010218V01 80010310V01 80010300V01 2574 2574 2574 2574 rearside rearside bottom rearside 37 37 38 38 Panel Panel Panel Panel New or changed product 25 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 30° XPol Panel 806–960 30° 18.5dBi 80010141 Type No. Frequency range Polarization Gain Half-power beam width Copolar +45°/ –45° 806–960 806 – 894 MHz 880 – 960 MHz +45°, –45° +45°, –45° 2 x 18 dBi Horizontal: Vertical: 2 x 18.5 dBi 31° 15° Horizontal: Vertical: Front-to-back ratio, copolar > 25 dB > 29 dB Isolation > 30 dB > 30 dB < 1.5 < 1.5 VSWR 29° 14° Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Bottom Weight Wind load (at 150 km/h) Height/width/depth 22 kg Frontal / lateral / rearside: 680 / 130 / 970 N 1296 / 560 / 116 mm XPol Panel 790–960 30° 21dBi 0°T 80010643 Type No. Frequency range Polarization Gain at 0° T Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 26 s clamp d e includ 790 – 862 MHz +45°, –45° 2 x 20.2 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 20.4 dBi 880 – 960 MHz +45°, –45° 2 x 20.8 dBi 33° > 30 dB 32° > 30 dB 30° > 30 dB Typically: 30 dB Typically: 26 dB 2.0 dB ±2.0° Typically: 23 dB 8.4° 8.2° 7.4° > 15 dB > 15 dB > 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 1760 / 330 / 2040 N 2254 / 576 / 99 mm H (Heavy) 20.5 kg / 22.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 806 – 960 X 30° 800/900 XPol Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 30° 20.5dBi 0°–10°T s clamp d e d lu c in 80010456V02 Type No. Frequency range 790 – 862 MHz +45°, –45° 2 x 20.0 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 20.2 dBi 880 – 960 MHz +45°, –45° 2 x 20.5 dBi 33° > 28 dB 32° > 29 dB 30° > 30 dB Typically: 25 dB Typically: 23 dB 2.5 dB ±2.0° Typically: 20 dB Polarization Gain at 0° T Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 8.8° 8.5° 0.5°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T > 16 ... 13 ... 13 dB > 18 ... 18 ... 17 dB > 18 ... 16 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom continuously adjustable Frontal / lateral / rearside:1760 / 330 / 2040 N 2254 / 576 / 99 mm H (Heavy) 22 kg / 24 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 9.1° For more information about additional mounting accessories please refer to page 186 27 800/900 XPol Panel Dual Polarization Half-power Beam Width 806 – 960 X 65° XPol Panel 806–960 65° 9dBi 739619 Type No. Frequency range 806–960 Polarization Gain 880 – 960 MHz +45°, –45° +45°, –45° 2 x 8.5 dBi Half-power beam width Copolar +45°/ –45° Horizontal: Vertical: Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 806 – 880 MHz 0° ±60° 2 x 9 dBi 70° 70° Horizontal: Vertical: 65° 68° > 27 dB > 27 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Isolation > 30 dB VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 350 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Bottom or top Weight Wind load (at 150 km/h) 3 kg Frontal / lateral / rearside: 40 / 25 / 90 N Height/width/depth 256 / 262 / 116 mm XPol Panel 806–960 65° 12.5dBi 739620 Type No. Frequency range 806–960 806 – 880 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° Gain 2 x 12 dBi 2 x 12.5 dBi Half-power beam width Copolar +45°/ –45° Horizontal: Vertical: 68° 29° Horizontal: Vertical: Front-to-back ratio, copolar > 30 dB Isolation > 30 dB VSWR 65° 27° < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input Connector position Weight Wind load (at 150 km/h) Height/width/depth 28 2 x 7-16 female Bottom or top 6 kg Frontal / lateral / rearside: 110 / 60 / 240 N 656 / 262 / 116 mm For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 790 – 960 X 800/900 XPol 65° XPol Panel 790–960 65° 15dBi 0°T s clamp d e includ 80010202V02 Type No. 790 – 862 MHz +45°, –45° 2 x 14.5 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 14.7 dBi 880 – 960 MHz +45°, –45° 2 x 15 dBi 69° > 23 dB 68° > 24 dB 65° > 25 dB > 20 dB > 11 dB > 20 dB > 11 dB 0.5 dB ±2° 14.7° 14.3° 13.2° > 14 dB > 15 dB > 14 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR Isolation Intermodulation IM3 Max. power per input > 20 dB > 11 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Bottom Wind load (at 150 km/h) Frontal / lateral / rearside: 430 / 200/ 600 N Height/width/depth 1294 / 259 / 99 mm Category of mounting hardware Weight Scope of supply M (Medium) 6.5 kg / 8.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 15dBi 6°T s clamp d e d lu c in 80010207V01 Type No. 790 – 862 MHz 790–960 824 – 894 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 14.5 dBi 2 x 14.7 dBi 2 x 15 dBi Frequency range Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° 66° 65° 63° > 30 dB > 30 dB > 30 dB Tpyically: > 20 dB Typically: > 10 dB Typically: > 20 dB Typically: > 10 dB Typically: > 20 dB Typically: > 10 dB Vertical Pattern: Half-power beam width 16° 15.7° Electrical tilt 6°, fixed 6°, fixed 6°, fixed Sidelobe suppression for: first sidelobe above horizon sector 0°–30° above horizon > 13 dB > 13 dB > 14 dB > 14 dB > 16 dB > 14 dB VSWR Isolation < 1.4 14.6° < 1.3 > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 2 x 7-16 female Bottom Frontal / lateral / rearside: 790 / 370 / 1090 N 1294 / 259 / 99 mm M (Medium) 7.5 kg / 9.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 29 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 15dBi 0°–14°T 790 – 862 MHz +45°, –45° 14.5 ... 14.4 ... 14.3 0° ... 7° ... 14° 790 – 960 824 – 894 MHz +45°, –45° 14.7 ... 14.5 ... 14.4 0° ... 7° ... 14° 67° > 24 dB 66° > 25 dB 65° > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon 15.5° 15° 0°– 14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 15 ... 14 ... 15 dB 18 ... 15 ... 15 dB 18 ... 15 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 440 / 210 / 610 N 1294 / 259 / 99 mm M (Medium) 8.5 kg Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 17dBi 0°T 80010203V02 Type No. VSWR Isolation Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 30 s clamp d e d lu c in 790 – 862 MHz +45°, –45° 2 x 16.4 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 16.6 dBi 880 – 960 MHz +45°, –45° 2 x 16.9 dBi 69° > 25 dB 67° > 25 dB 65° > 25 dB > 22 dB > 18 dB > 14 dB > 22 dB > 18 dB > 14 dB 0.5 dB ±2.0° 9.9° 9.5° 8.9° > 13 dB > 15 dB > 15 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±30° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon 880 – 960 MHz +45°, –45° 15 ... 14.8 ... 14.7 0° ... 7° ... 14° 15.7° VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 80010303V02 Type No. > 22 dB > 18 dB > 14 dB < 1.5 < 1.5 < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 690 / 310 / 910 N 1934 / 259 / 99 M (Medium) 9.5 kg / 11.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 790 – 960 X 65° 800/900 XPol Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 65° 17dBi 6°T 790 – 862 MHz +45°, –45° 2 x 16.2 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 16.5 dBi 880 – 960 MHz +45°, –45° 2 x 16.9 dBi 69° > 25 dB 68° > 25 dB 65° > 25 dB Typ. > 20 dB Typ. > 10 dB Typ. > 20 dB Typ. > 10 dB 1 dB ±1.5° Typ. > 20 dB Typ. > 10 dB 9.4° 6°, fixed 9.3° 6°, fixed 8.8° 6°, fixed > 14 dB > 15 dB > 15 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon VSWR Isolation Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 80010294V02 Type No. < 1.5 < 1.4 < 1.3 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 690 / 310 / 910 N 1934 / 259 / 99 mm M (Medium) 9.5 kg / 11.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 16.5dBi 0°–10°T 790 – 862 MHz +45°, –45° 16.2 ... 16.4 ... 16.2 0° ... 5° ... 10° 790–960 824 – 894 MHz +45°, –45 16.3 ... 16.6 ... 16.3 0° ... 5° ... 10° 880 – 960 MHz +45°, –45° 16.6 ... 16.8 ... 16.6 0° ... 5° ... 10° 69° > 24 dB 68° > 25 dB 65° > 25 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB 0.5 dB ±1.5° Typically: 20 dB > 10 dB Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Isolation, between ports VSWR Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e d lu c in 80010634V01 Type No. 10° 9.9° 9.7° 0° – 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB > 30 dB < 1.5 < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 680 / 310 / 900 N 1934 / 259 / 99 mm M (Medium) 10.5 kg / 12.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 31 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 18dBi 0°T 80010204V02 Type No. 790 – 862 MHz +45°, –45° 2 x 17.2 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 17.5 dBi 880 – 960 MHz +45°, –45° 2 x 17.8 dBi 69° > 25 dB 67° > 25 dB 65° > 25 dB > 25 dB > 14 dB > 25 dB > 14 dB 1.0 dB ±2.0° 8.5° 8.3° 7.8° > 13 dB > 14 dB > 15 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for: first sidelobe above horizon VSWR Isolation Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ > 25 dB > 14 dB < 1.5 < 1.4 < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 790 / 370 / 1090 N 2254 / 259 / 99 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 17.5dBi 0°–8°T 80010305V02 Type No. Frequency range 790 – 862 MHz +45°, –45° 16.8 ... 17 ... 16.7 0° ... 4° ... 8° s clamp d e d lu c in 790–960 824 – 894 MHz +45°, –45° 16.9 ... 17.1 ... 16.9 0° ... 4° ... 8° 880 – 960 MHz Polarization +45°, –45° Average gain (dBi) 17.2 ... 17.4 ... 17.0 Tilt 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 69° 67° 65° Front-to-back ratio, copolar > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dB Sector ±60° Typically: > 10 dB Typically: > 10 dB Typically: > 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 9.1° 8.8° 8.5° Electrical tilt 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 8° T 0° ... 2° ... 4° ... 8° T 0° ... 2° ... 4° ... 8° T sidelobe above main beam 18 ... 18 ... 18 ... 16 dB 18 ... 18 ... 18 ... 16 dB 20 ... 18 ... 17 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 32 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 800 / 390 / 1090 N 2254 / 259 / 99 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 790 – 960 X 800/900 XPol 65° XPol Panel 790–960 65° 18dBi 0°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam Null-fill s clamp d e includ 80010215V01 Type No. 790 – 866 MHz +45°, –45° 2 x 17.7 dBi VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790–960 824 – 894 MHz +45°, –45° 2 x 17.9 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 69° > 25 dB > 25 dB > 12 dB 67° > 25 dB > 25 dB > 12 dB 0.5 dB ±2.0° 65° > 25 dB > 25 dB > 12 dB 7.4° 7.2° 6.8° ≥ 14 dB ≥ 15 dB Typically: –25 dB ≥ 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 18dBi 6°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Null-fill VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e d lu c in 80010208V01 Type No. 790 – 866 MHz +45°, –45° 2 x 17.7 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 17.9 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 69° > 25 dB > 25 dB > 10 dB 67° > 25 dB > 25 dB > 10 dB 0.5 dB ±2.5° 65° > 25 dB > 25 dB > 10 dB 7.4° 7.2° 6°, fixed 6.8° ≥ 16 dB ≥ 17 dB Typically: –25 dB ≥ 17 dB < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 33 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 18dBi 9°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Null-fill s clamp d e includ 80010214V01 Type No. 790 – 862 MHz +45°, –45° 2 x 17.6 dBi 790–960 824 – 894 MHz +45°, –45° 2 x 17.8 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 69° > 25 dB > 25 dB > 10 dB 67° > 25 dB > 25 dB > 10 dB 1.0 dB ±2.5° 65° > 25 dB > 25 dB > 10 dB 7.4° 7.2° 9°, fixed 6.8° ≥ 13 dB ≥ 15 dB Typically: –25 dB ≥ 16 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 65° 17.5dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Null-fill at 0° tilt VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 34 s clamp d e d lu c in 80010306V02 Type No. 790 – 862 MHz +45°, –45° 17.0 ... 17.1 ... 17.0 0.5° ... 5° ... 9.5° 790–960 824 – 894 MHz +45°, –45° 17.1 ... 17.2 ... 17.1 0.5° ... 5° ... 9.5° 880 – 960 MHz +45°, –45° 17.3 ... 17.4 ... 17.3 0.5° ... 5° ... 9.5° 68° > 24 dB Typically: 23 dB Typically: > 10 dB 66° > 25 dB Typically: 23 dB Typically: > 10 dB 1 dB ±2° 65° > 25 dB Typically: 25 dB Typically: > 10 dB 7.7° 7.5° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 15 dB Typically: –25 dB 7.3° 0.5° ... 5° ... 9.5° T ≥ 17 ... 14 ... 14 dB 0.5° ... 5° ... 9.5° T ≥ 20 ... 18 ... 18 dB < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female (long neck) Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 940 / 440 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 790 – 960 X 800/900 XPol 65° XPol Panel 790–960 65° 18dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression – for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 80010307V01 Type No. 790 – 862 MHz +45°, –45° 17.4 ... 17.5 ... 17.4 0.5° ... 5° ... 9.5° 790–960 824 – 894 MHz +45°, –45° 17.5 ... 17.6 ... 17.5 0.5° ... 5° ... 9.5° 880 – 960 MHz +45°, –45° 17.7 ... 17.9 ... 17.7 0.5° ... 5° ... 9.5° 68° > 24 dB Typically: 22 dB Typically: > 10 dB 67° > 25 dB Typically: 23 dB Typically: > 10 dB 1.0 dB ±2.0° 65° > 25 dB Typically: 25 dB Typically: > 10 dB 7.7° 7.5° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 15 dB 7.3° 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 15 dB 0.5° ... 5° ... 9.5° T ≥ 18 ... 16 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 13 kg / 15 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 35 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 85° XPol Panel 790–960 85° 13.5dBi 0°–14°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam s clamp d e includ 80010308V01 Type No. 790 – 862 MHz +45°, –45° 13.2 ... 13.3 ... 13.2 dBi 0° ... 7° ... 14° 790–960 824 – 894 MHz +45°, –45° 13.3 ... 13.4 ... 13.3 dBi 0° ... 7° ... 14° 880 – 960 MHz +45°, –45° 13.4 ... 13.5 ... 13.4 dBi° 0° ... 7° ... 14° 86° > 24 dB > 20 dB Typically: 20 dB > 10 dB 85° > 24 dB > 22 dB Typically: 20 dB > 10 dB 0.5 dB ±1.5° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 16° 15.5° 0°–14°, continuously adjustable 0° ... 7° ... 14° T ≥ 17 ... 17 ... 16 dB 15° 0° ... 7° ... 14° T ≥ 17 ... 16 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 0° ... 7° ... 14° T ≥ 17 ... 16 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 430 / 200 / 590 N 1294 / 259 / 99 mm M (Medium) 9 kg / 11 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 790–960 85° 15dBi 0°–10°T Frequency range Polarization Average gain Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam: Avg.: VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 36 s clamp d e d lu c in 80010309V01 Type No. 790 – 862 MHz +45°, –45° 14.8 ... 15.0 ... 14.6 dBi 0° ... 5° ... 10° 790–960 824 – 894 MHz +45°, –45° 14.9 ... 15.1 ... 14.7 dBi 0° ... 5° ... 10° 880 – 960 MHz +45°, –45° 14.8 ... 15.2 ... 15.0 dBi° 0° ... 5° ... 10° 85° > 25 dB > 21 dB Typically: 23 dB > 10 dB 85° > 25 dB > 21 dB Typically: 22 dB > 10 dB 0.5 dB ±3.0° 83° > 26 dB > 21 dB Typically: 22 dB > 10 dB 10.1° 9.8° 0°–10°, continuously adjustable 0° ... 5° ... 10° T ≥ 15 ... 15 ... 15 dB ≥ 20 ... 20 ... 20 dB 9.6° 0° ... 5° ... 10° T ≥ 15 ... 15 ... 14 dB ≥ 19 ... 19 ... 19 dB 0° ... 5° ... 10° T ≥ 18 ... 18 ... 18 dB ≥ 22 ... 22 ... 22 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 680 / 310 / 900 N 1934 / 259 / 99 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 790 – 960 X 800/900 XPol 85° XPol Panel 790–960 85° 17dBi 0°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam s clamp d e includ 80010217V01 Type No. 790 – 862 MHz +45°, –45° 16.6 dBi > > > > VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 86° 25 dB 23 dB 20 dB 15 dB 790–960 824 – 894 MHz +45°, –45° 16.7 dBi 85° > 25 dB > 24 dB > 20 dB > 15 dB 1.0 dB ±4.5° 880 – 960 MHz +45°, –45° 16.8 dBi > > > > 83° 25 dB 24 dB 20 dB 13 dB 7.5° 7.3° 7.0° 16 dB 17 dB 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 790–960 85° 17dBi 6°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e d lu c in 80010218V01 Type No. 790 – 862 MHz +45°, –45° 16.3 dBi 790–960 824 – 894 MHz +45°, –45° 16.5 dBi 880 – 960 MHz +45°, –45° 16.9 dBi 86° > 24 dB > 22 dB Typically: 20 dB > 14 dB 85° > 25 dB > 23 dB Typically: 20 dB > 14 dB 0.5 dB ±2.5° 83° > 27 dB > 25 dB Typically: 20 dB > 12 dB 7.6° 7.3° 6°, fixed 7.0° 17 dB 16 dB 16 dB < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 37 800/900 XPol Panel Dual Polarization Half-power Beam Width 790 – 960 X 85° XPol Panel 790–960 85° 16dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam s clamp d e includ 80010310V01 Type No. 790 – 862 MHz +45°, –45° 15.8 ... 15.6 ... 15.4 dBi 0.5° ... 5° ... 9.5° 790–960 824 – 894 MHz +45°, –45° 16.0 ... 15.9 ... 15.8 dBi 0.5° ... 5° ... 9.5° 880 – 960 MHz +45°, –45° 16.2 ... 16.2 ... 16.2 dBi° 0.5° ... 5° ... 9.5° 86° > 24 dB > 20 dB Typically: 20 dB > 10 dB 85° > 24 dB > 22 dB Typically: 20 dB > 10 dB 0.5 dB ±3.5° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 8.1° 7.9° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T ≥ 18 ... 17 ... 16 dB 7.6° 0.5° ... 5° ... 9.5° T ≥ 18 ... 14 ... 14 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 0.5° ... 5° ... 9.5° T ≥ 17 ... 16 ... 16 dB < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 950 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 790–960 85° 16.5dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±0°) Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 38 s clamp d e d lu c in 80010300V01 Type No. 790 – 862 MHz +45°, –45° 16.2 ... 16.2 ... 15.8 dBi 0.5° ... 5° ... 9.5° 790–960 824 – 894 MHz +45°, –45° 16.3 ... 16.3 ... 16.1 dBi 0.5° ... 5° ... 9.5° 880 – 960 MHz +45°, –45° 16.5 ... 16.6 ... 16.5 dBi° 0.5° ... 5° ... 9.5° 85° > 24 dB > 21 dB Typically: 20 dB > 10 dB 85° > 25 dB > 23 dB Typically: 20 dB > 10 dB 0.5 dB ±3.5° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 8° 7.8° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T ≥ 18 ... 17 ... 16 dB 7.6° 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 14 dB 0.5° ... 5° ... 9.5° T ≥ 18 ... 16 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Summary – Directional Antennas 2-Broad-band 800/900 Dual Polarization + 45°/ –45° Type No. Height [mm] Connector position Page XXPol Panel 790–862 880–960 65° 65° 14.5dBi 15dBi 0°–12°T 0°–12°T 80010667 1355 bottom 40 XXPol Panel 790–862 880–960 65° 65° 16dBi 16.5dBi 0°–10°T 0°–10°T 80010668 1934 bottom 41 XXPol Panel 824–960 824–960 60° 60° 16dBi 16dBi 0°–10°T 0°–10°T 80010516V01 2024 rearside 42 XXPol Panel 790–960 790–960 65° 65° 17.5dBi 17.5dBi 0°–8°T 0°–8°T 80010647V01 2254 rearside 43 XXPol Panel 824–960 824–960 65° 65° 17dBi 17dBi 0°–8°T 0°–8°T 80010517V01 2631 rearside 44 XXPol Panel 824–960 824–960 88° 88° 17dBi 17dBi 0°–8°T 0°–8°T 80010518V01 2631 rearside 45 800/900 XXPol Type New or changed product ying deplo as, When nd Antenn ng i a b u r d e s a 2-Bro lso consid biners ea om pleas l Hybrid C 2) 5 a i spec age 2 (see p 39 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 X X 65° 65° XXPol Panel 790–862/880–960 65°/ 65° 14.5/15dBi 0°–12°/0°–12°T 80010667 800/900 XXPol Type No. Frequency range s clamp d e d lu c in 790–862 790 – 862 MHz 880–960 880 – 960 MHz +45°, –45° +45°, –45° 14.3 ... 14.4 ... 14.1 0° ... 6° ... 12° 14.8 ... 15.0 ... 14.6 0° ... 6° ... 12° 68° 64° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB Cross polar ratio Maindirection Sector 0° ±60° 20 dB > 10 dB 20 dB > 10 dB 15.2° 13.9° Electrical tilt, continuously adjustable 0°– 12° 0°– 12° 0° ... 6° ... 12° T ≥ 17 ... 16 ... 15 dB 0° ... 6° ... 12° T ≥ 17 ... 15 ... 15 dB Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Vertical Pattern: Half-power beam width Min. sidelobe suppression for first sidelobe above main beam VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 30 dB (790–862 // 880–960 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 350 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 630 / 220 / 730 N Height/width/depth 1355 / 303 / 99 mm Category of mounting hardware M (Medium) Weight Scope of supply 40 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 790 – 862 –45° 790 – 862 +45° 880 – 960 –45° 880 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 X X 65° 65° XXPol Panel 790–862/880–960 65°/ 65° 16/16.5dBi 0°–10°/0°–10°T Frequency range 790–862 790 – 862 MHz 880–960 880 – 960 MHz +45°, –45° +45°, –45° 15.9 ... 16.0 ... 15.8 0° ... 5° ... 10° 16.3 ... 16.6 ... 16.1 0° ... 5° ... 10° 67° 63° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB Cross polar ratio Maindirection Sector 0° ±60° 23 dB > 10 dB 25 dB > 10 dB 10° 9.7° Electrical tilt, continuously adjustable 0°– 10° 0°– 10° 0° ... 5° ... 10° T ≥ 17 ... 16 ... 16 dB 0° ... 5° ... 10° T ≥ 18 ... 16 ... 16 dB Polarization Average gain (dBi) Tilt 800/900 XXPol s clamp d e d lu c in 80010668 Type No. Horizontal Pattern: Half-power beam width Vertical Pattern: Half-power beam width Min. sidelobe suppression for first sidelobe above main beam VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 30 dB (790–862 // 880–960 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 400 W (at 50 °C ambient temperature Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 920 / 320 / 1050 N Height/width/depth 1934 / 303 / 99 mm Category of mounting hardware M (Medium) Weight 18.5 kg / 20.5 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter) 790 – 862 –45° 790 – 862 +45° 880 – 960 –45° 880 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 41 2-Multi-band Panel Dual Polarization Half-power Beam Width 824 – 960 824 – 960 X X 60° 60° XXPol Panel 824–960/824–960 60°/60° 16/16dBi 0°–10°/0°–10°T 800/900 XXPol s clamp d e d lu inc 80010516V01 Type No. Frequency range 824–960 Polarization 824 – 894 MHz 880 – 960 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 15.5 dBi 4 x 15.7 dBi Gain at 0° Tilt Horizontal Pattern: Half-power beam width 60° 58° > 25 dB > 25 dB Typically: 15 dB > 10 dB Typically: 16 dB > 10 dB 9.8° 9.3° Front-to-back ratio Cross polar ratio Sector 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 0°– 10°, continuously adjustable 0° ... 5° ... 10° T ≥ 14 ... 15 ... 15 dB VSWR Isolation, between ports 0° ... 5° ... 10° T ≥ 14 ... 15 ... 15 dB < 1.5 Typically: > 25 dB Typically: > 28 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Rearside, pointing downwards Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 910 / 300 / 1150 N Height/width/depth 2024 / 374 / 169 mm Category of mounting hardware H (Heavy) Weight Scope of supply 42 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 824 – 960 –45° 824 – 960 –45° 824 – 960 +45° 824 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 790 – 960 790 – 960 X X 65° 65° XXPol Panel 790–960/790–960 65°/65° 17.5/17.5dBi 0°–8°/0°–8°T s clamp d e d lu inc 80010647V01 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 894 MHz +45°, –45° +45°, –45° +45°, –45° 16.9 ... 17.1 ... 17.0 0° ... 4° ... 8° 17.0 ... 17.2 ... 17.1 0° ... 4° ... 8° 17.3 ... 17.4 ... 17.1 0° ... 4° ... 8° 800/900 XXPol 2-Multi-band Panel Dual Polarization Half-power Beam Width 880 – 960 MHz Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° 66° 65° 64° > 27 dB > 27 dB > 27 dB Typically: 25 dB Typically: > 10 dB Typically: 25 dB Typically: > 10 dB Typically: 25 dB Typically: > 10 dB Tracking, Avg. 1.0 dB Squint ±2.5° Vertical Pattern: Half-power beam width 9.1° Electrical tilt 9.0° 8.5° 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 3° ... 6° ... 8° T 0° ... 3° ... 6° ... 8° T 0° ... 3° ... 6° ... 8° T sidelobe above main beam avg. 18 ... 18 ... 16 ... 15 dB 18 ... 18 ... 16 ... 15 dB 18 ... 18 ... 16 ... 15 dB VSWR < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 400 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Rearside Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1760 / 330 / 2040 N Height/width/depth 2254 / 576 / 99 mm Category of mounting hardware H (Heavy) Weight Scope of supply 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 790 – 960 –45° 790 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 43 2-Multi-band Panel Dual Polarization Half-power Beam Width 824– 960 824– 960 X X 65° 65° XXPol Panel 824–960/824–960 65°/65° 17/17dBi 0°–8°/0°–8°T 800/900 XXPol s clamp d e d lu c in 80010517V01 Type No. Frequency range 824–960 Polarization 824 – 894 MHz 880 – 960 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 16.5 dBi 4 x 16.7 dBi Gain at 0° Tilt Horizontal Pattern: Half-power beam width 66° 61° > 25 dB > 25 dB Typically: 16 dB > 8 dB Typically: 17 dB > 10 dB 7.2° 6.8° Front-to-back ratio Cross polar ratio Sector 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 0°– 8°, continuously adjustable 0° ... 4° ... 8° T ≥ 15 ... 15 ... 15 dB VSWR Isolation, between ports 0° ... 4° ... 8° T ≥ 15 ... 16 ... 15 dB < 1.5 Typically: > 25 dB > 28 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Rearside, pointing downwards Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1210 / 400 / 1540 N Height/width/depth 2631 / 374 / 169 mm Category of mounting hardware H (Heavy) Weight Scope of supply 44 28 kg / 30 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 824 – 960 –45° 824 – 960 –45° 824 – 960 +45° 824 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 2-Multi-band Panel Dual Polarization Half-power Beam Width 824– 960 824– 960 X X 88° 88° XXPol Panel 824–960/824–960 88°/88° 17/17dBi 0°–8°/0°–8°T s clamp d e d lu c in 80010518V01 Type No. Frequency range Polarization 880 – 960 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 16.5 dBi 4 x 17 dBi Gain at 0° Tilt 800/900 XXPol 824–960 824 – 894 MHz Horizontal Pattern: Half-power beam width 88° 85° > 25 dB > 25 dB Typically: 15 dB > 10 dB Typically: 15 dB > 10 dB Front-to-back ratio Cross polar ratio Sector 0° ±60° Tracking, Avg. 0.5 dB Squint ±4.5° Vertical Pattern: Half-power beam width 7.2° Electrical tilt Sidelobe suppression for first sidelobe above main beam 6.8° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T ≥ 15 ... 15 ... 15 dB VSWR Isolation, between ports 0° ... 4° ... 8° T ≥ 16 ... 16 ... 15 dB < 1.5 Typically: > 25 dB > 28 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Rearside, pointing downwards Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1210 / 400 / 1540 N Height/width/depth 2631 / 374 / 169 mm Category of mounting hardware H (Heavy) Weight Scope of supply 28 kg / 30 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 824 – 960 –45° 824 – 960 –45° 824 – 960 +45° 824 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 45 46 Summary – Directional Antennas Vertical Polarization 800/900 / 1800/1900/2000 VPol – 800/900 VPol Panel Dual Yagi VPol BiDir VPol BiDir 870–960 Type No. Height [mm] Connector position Page 20° 16.5dBi 0°T 735727 492 bottom 48 870–960 C 33° 1710–2170 26° 15.5dBi 18dBi 0°T 0°T 80010658 170 rearside 49 790–960 / 1710–2170 790–960 / 1710–2170 65° 65° 5dBi 5dBi 0°T 0°T 738445 738446 312 312 790–2690 65° 11dBi 0°T 742192V01 300 bottom 51 VPol Panel 860–960 65° 9dBi 0°T 730677 264 bottom or top 52 VPol Panel 806–960 65° 15.5dBi 0°T 730368 1294 bottom 52 VPol Panel 806–960 65° 17dBi 0°T 730691 1934 rearside 53 VPol Panel 806–960 65° 18.5dBi 0°T 730376V01 2574 rearside 53 VPol Panel 872–960 90° 7.5dBi 0°T 736854 262 bottom or top 54 VPol Panel 806–960 90° 17dBi 0°T 730378V01 2574 rearside 54 VPol Panel 870–960 120° 16dBi 0°T 730382 2574 rearside 55 VPol LogPer 800/900 VPol 1800/1900/2000 VPol Type 50 50 VPol – 800/900 / 1800/1900/2000 VPol Panel 1710–2180 12° 18.5dBi 0°T 80010368 299 side 56 Dual Yagi 870–960 C 33° 1710–2170 26° 15.5dBi 18dBi 0°T 0°T 80010658 170 rearside 49 VPol BiDir VPol BiDir VPol LogPer 790–960 / 1710–2170 790–960 / 1710–2170 65° 65° 5dBi 5dBi 0°T 0°T 738445 738446 312 312 50 50 790–2690 65° 11dBi 0°T 742192V01 300 bottom 51 VVPol – 800/900 – 1800–2000 VVPol Panel 824–960 1710–2170 C 90° 82° 7dBi 7dBi 0°T 0°T 742290 328 bottom or top 57 VVPol Panel 824–960 1710–2170 C 90° 82° 10dBi 11dBi 0°T 0°T 80010046 662 bottom or top 57 C = integrated Combiner New or changed product Additional versions on request 47 Panel Vertical Polarization Half-power Beam Width 870 – 960 V 20° VPol Panel 870–960 20° 16.5dBi 735727 800/900 VPol 1800/1900/2000 VPol Type No. Input 7-16 female Frequency range 870 – 960 MHz VSWR < 1.3 Gain 16.5 dBi Polarization Vertical Front-to-back ratio > 24 dB Half-power Beam Width Intermodulation IM3 Max. power H-plane: 20°/ E-plane: 33° < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Weight 10 kg Wind load Frontal: 500 N (at 150 km/h) Lateral: 70 N (at 150 km/h) Rearside: 715 N (at 150 km/h) Height/width/depth 492 / 992 / 190 mm Material: Radiator: Aluminum. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: All metal parts of the antenna as well as the inner conductor are DC grounded. Accessories (order separately) Description Remarks Weight approx. 738546 1 clamp Mast: 42 – 115 mm diameter 1.1 kg 85010002 1 clamp Mast: 110 – 220 mm diameter 2.7 kg 85010003 1 clamp Mast: 210 – 380 mm diameter 4.8 kg Type No. 48 Yagi Multi-band Antenna Dual Polarization Half-power Beam Width 870 – 960 1710 –2170 +45° –45° 33° 26° Dual Yagi 870–960/1710–2170 C 33°/26° 15.5/18dBi 80010658 Frequency range VSWR Gain (average) Polarization Front-to-back ratio Half-power beam width (avg.) horizontal vertical Max. power Input Connector position Weight Wind load Dimensions Integrated combiner 870–960 870 – 960 MHz 1710–2170 1710 – 1880 MHz 1920 – 2170 MHz < 1.5 < 1.5 < 1.5 15.5 dBi 15.5 dBi 18 dBi +45° –45° –45° ≥ 24 dB ≥ 27 dB ≥ 27 dB 33° 33° 30° 29° 23° 24° 800/900 VPol 1800/1900/2000 VPol Type No. 100 W (at 50 °C ambient temperature) 1 x 7-16 female Rearside 4.0 kg 200 N (at 150 km/h) 1100 / ∅ 170 mm The insertion loss is included in the given antenna gain values. 1710 – 2170 –45° 870 – 960 +45° C 7-16 49 Multi-band Bidirectional Antenna Vertical Polarization Half-power Beam Width 790 – 960/1710 –2170 V 65° VPol BiDir 790–960/1710–2170 65° 5dBi Type No. 738445 738446 Input 1 x 7-16 female 1 x N female Frequency range 790 – 960 MHz, 1710 – 2170 MHz 800/900 VPol 1800/1900/2000 VPol VSWR 790 – 806 MHz: < 2.2 806 – 824 MHz: < 1.7 824 – 960 / 1710 – 2170 MHz: < 1.5 Gain 790 – 960 MHz: 5 dBi 1710 – 1880 MHz: 5.5 dBi 1880 – 2170 MHz: 6.5 dBi Impedance 50 Ω Polarization Vertical Max. power (total) 200 W (at 50 °C ambient temperature) Weight 0.8 kg Wind load Frontal: Lateral: Rearside: Max. wind velocity 25 N (at 150 km/h) 65 N (at 150 km/h) 35 N (at 150 km/h) 200 km/h Packing size 422 x 212 x 95 mm Height/width/depth 312 / 55 / 188 mm Material: Radiator: Tin-plated copper. Reflector: Weather-proof aluminum. Radome: High impact plastic, colour: Grey. All screws and nuts: Stainless steel. Mounting: Wall mounting: No additional mounting kit needed. For pipe mast mounting use clamps listed below (order separately). Ice protection: The radiating system is protected by the radome. Due to its very sturdy construction, the antenna remains operational even under icy conditions. Grounding: All metal parts of the antenna as well as the inner conductor are DC grounded. Accessories (order separately) Type No. Description 734360 734361 734362 734363 734364 734365 50 2 2 2 2 2 2 clamps clamps clamps clamps clamps clamps Weight Units per approx. antenna Remarks Mast: Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 45 – – – – – – 60 80 100 120 140 125 mm mm mm mm mm mm diameter diameter diameter diameter diameter diameter 60 g 70 g 80 g 90 g 110 g 80 g 1 1 1 1 1 1 Logarithmic Periodic Vertical Polarization Half-power Beam Width 790 – 2690 V 65° VPol LogPer 790–2690 65° 11dBi 742192V01 Frequency range VSWR Gain 790 – 960 MHz 960 – 1710 MHz < 1.5 < 1.5 1710 – 2200 MHz 2200 – 2490 MHz 2490 – 2690 MHz < 1.5 < 1.5 < 1.5 10.8 dBi 11.0 dBi 11.2 dBi 11.0 dBi 10.8 dBi Impedance 50 Ω 50 Ω 50 Ω 50 Ω 50 Ω Polarization Vertical Vertical Vertical Vertical Vertical Front-to-back ratio > 25 dB > 25 dB > 25 dB > 22 dB > 25 dB 65° 53° 60° 50° 55° 47° 50° 45° 50° 45° < –150 dBc < –150 dBc < –150 dBc < –150 dBc < –150 dBc Half-power Beam Width horizontal vertical Intermodulation IM3 (2 x 43 dBm carrier) Max. power Total power 300 W 250 W 200 W 170 W 500 W (at 50 °C ambient temperature) Input 150 W 1 x 7-16 female Connector position Bottom Weight Wind load (at 150 km/h) 800/900 VPol 1800/1900/2000 VPol Type No. 5.7 kg Frontal / lateral / rearside: 20 / 210 / 30 N Max. wind velocity 200 km/h Height/width/depth 300 / 155 / 785 mm Material: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Mounting: The antenna can be mounted on tubular mast with a diameter of 30 – 70 mm with supplied clamps. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: All metal parts of the antenna as well as the inner conductor are DC grounded. 51 Panel Vertical Polarization Half-power Beam Width 806 – 960 V 65° VPol Panel 860–960 65° 9dBi Type No. 730677 Frequency range 860 – 960 MHz Polarization Vertical Gain 9 dBi 800/900 VPol 1800/1900/2000 VPol Half-power beam width Front-to-back ratio H-plane: 65° E-plane: 70° > 25 dB (890 – 960 MHz) > 20 dB (860 – 890 MHz) VSWR Intermodulation IM3 Max. power < 1.3 < –150 dBc (2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) Input N female Connector position Bottom or top Weight Wind load (at 150 km/h) 1.2 kg Frontal / lateral / rearside: 65 / 28 / 110 N Height/width/depth 264 / 258 / 103 mm VPol Panel 806–960 65° 15.5dBi 730368 Type No. Frequency range 806 – 866 MHz Polarization Gain 806–960 824 – 894 MHz 880 – 960 MHz Vertical 15.0 dBi 15.2 dBi 15.5 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) 68° 67° 65° > 25 dB > 25 dB > 25 dB 14° 13.5° 13° Vertical Pattern: Half-power beam width VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input Connector position Weight Wind load (at 150 km/h) Height/width/depth 52 7-16 female Bottom 6 kg Frontal / lateral / rearside: 350 / 155 / 580 N 1294 / 259 / 99 mm For more information about additional mounting accessories please refer to page 186 Panel Vertical Polarization Half-power Beam Width 806 – 960 V 65° VPol Panel 806–960 65° 17dBi 730691 Type No. Frequency range 806 – 866 MHz 806–960 824 – 894 MHz 16.4 dBi 16.7 dBi 17.0 dBi 68° 67° 65° > 25 dB > 25 dB > 25 dB 9.5° 9.3° 8.5° Polarization Gain 880 – 960 MHz Vertical Half-power beam width Front-to-back ratio (180°±30°) 800/900 VPol 1800/1900/2000 VPol Horizontal Pattern: Vertical Pattern: Half-power beam width VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input 7-16 female Connector position Rearside Weight 9 kg Wind load (at 150 km/h) Frontal / lateral / rearside: 550 / 250 / 930 N Height/width/depth 1934 / 259 / 99 mm VPol Panel 806–960 65° 18.5dBi Frequency range 806 – 866 MHz Polarization Gain s clamp d e d lu c in 730376V01 Type No. 806–960 824 – 894 MHz 880 – 960 MHz Vertical 17.9 dBi 18.1 dBi 18.5 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) 68° 67° 65° > 25 dB > 25 dB > 25 dB 7.4° 7.2° 6.8° > 17 dB > 17 dB > 18 dB Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 7-16 female Rearside Frontal / lateral / rearside: 740 / 330 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 53 Panel Vertical Polarization Half-power Beam Width 870 – 960 V 90° VPol Panel 872–960 90° 7.5dBi Type No. 736854 Frequency range 872 – 960 MHz Polarization Vertical Gain 7.5 dBi 800/900 VPol 1800/1900/2000 VPol Half-power beam width H-plane: 90° E-plane: 70° Front-to-back ratio > 20 dB VSWR Intermodulation IM3 Max. power < 1.5 < –140 dBc (2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) Input N female Connector position Bottom or top Weight 1.5 kg Wind load (at 150 km/h) Frontal / lateral / rearside: 45 / 20 / 60 N Height/width/depth 262 / 155 / 49 mm VPol Panel 806–960 90° 17dBi Frequency range 806 – 866 MHz Polarization Gain s clamp d e d lu c in 730378V01 Type No. 806–960 824 – 894 MHz 880 – 960 MHz Vertical 16.6 dBi 16.7 dBi 17.0 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) 90° 90° 90° > 22 dB > 22 dB > 22 dB 7.1° 6.9° 6.6° > 12 dB > 12 dB > 12 dB Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 500 W (at 50 °C ambient temperature) Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 54 7-16 female Rearside Frontal / lateral / rearside: 930 / 410 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Vertical Polarization Half-power Beam Width 870 – 960 V 120° VPol Panel 870–960 120° 16dBi Type No. 730382 Frequency range 870 – 960 MHz Gain Half-power beam width Front-to-back ratio VSWR Intermodulation IM3 Max. power Input Connector position Weight Wind load (at 150 km/h) Height/width/depth Vertical 16 dBi H-plane: 120° E-plane: 6.5° 800/900 VPol 1800/1900/2000 VPol Polarization > 20 dB < 1.3 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 7-16 female Rearside 12 kg Frontal / lateral / rearside: 740 / 330 / 1270 N 2574 / 258 / 103 mm For more information about additional mounting accessories please refer to page 186 55 Multi-band Panel Vertical Polarization Half-power Beam Width 1710 –2180 V 12° VPol Panel 1710–2180 12° 18.5dBi 0°T 80010368 800/900 VPol 1800/1900/2000 VPol Type No. Frequency range 1710 – 1880 MHz 1710–2180 1850 – 1990 MHz 1920 – 2180 MHz Polarization Vertical Vertical Vertical Gain 18.1 dBi 18.4 dBi 18.7 dBi 13.3° 12.8° 12° Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ± 30°) > 30 dB > 30 dB > 30 dB Sidelobe suppression > 18 dB > 18 dB > 17 dB 37° 36° 36° Electrical tilt 0°, fixed 0°, fixed 0°, fixed Sidelobe suppression for first sidelobe above main beam > 18 dB > 18 dB > 18 dB Vertical Pattern: Half-power beam width VSWR Intermodulation IM3 Max. power Input Connector position Weight Wind load (at 150 km/h) Height/width/depth 56 < 1.5 < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 1 x 7-16 female Side (see picture) 9 kg Frontal / lateral / rearside: 340 / 25 / 400 N 299 / 743 / 69 mm For more information about additional mounting accessories please refer to page 186 Dual-band Panel Vertical Polarization Half-power Beam Width 824 – 960 1710 –2170 V V 90° 82° VVPol Panel 824–960/1710–2170 C 90°/82° 7/7dBi 742290 Type No. Polarization Gain Half-power beam width Front-to-back ratio VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power 824 – 960 MHz 1710 – 2170 MHz Vertical Vertical 7 dBi 7 dBi Horizontal: Vertical: 90° 60° > 18 dB 82° 70° > 20 dB < 1.7 (824 – 960 MHz) < 1.7 (1710 – 2170 MHz) < 1.5 (870 – 960 MHz) < 1.5 (1710 – 1990 MHz) < –150 dBc < –150 dBc 100 W (at 50 °C ambient temperature) Input 1 x 7-16 female Connector position Bottom or top Weight Wind load (at 150 km/h) Horizontal: Vertical: 800/900 VPol 1800/1900/2000 VPol Frequency range 1710–2170 VPol 824–960 VPol 2.8 kg Frontal / lateral / rearside: 90 / 23 / 100 N C 328 / 155 / 69 mm 7-16 Height/width/depth VVPol Panel 824–960/1710–2170 C 90°/82° 10/11dBi Type No. Frequency range 80010046 824 – 960 MHz 1710 – 2170 MHz Polarization Vertical Vertical Gain 10 dBi 11 dBi Half-power beam width Front-to-back ratio VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Height/width/depth Horizontal: Vertical: 90° 33° Horizontal: Vertical: 82° 19° > 18 dB > 20 dB < 1.7 (824 – 960 MHz) < 1.5 (870 – 960 MHz) < 1.5 < –150 dBc < –150 dBc 100 W (at 50 °C ambient temperature) 1 x 7-16 female Bottom or top 5 kg Frontal / lateral / rearside: 175 / 47 / 200 N 662 / 155 / 69 mm 1710–2170 VPol 824–960 VPol C 7-16 For more information about additional mounting accessories please refer to page 186 57 Summary – Directional Antennas Dual Polarization + 45°/ –45° 1800/1900/2000/2600 Dual Polarization + 45°/ –45° Type Type No. Height [mm] Connector position Page XPol Panel 1710–2170 33° 20dBi 0°–12°T 80010251V01 1032 bottom 60 XPol Panel 1710–2170 33° 21dBi 0°–8°T 742351V01 1304 bottom 60 XPol Panel 1710–1880 33° 22dBi 2°T 741623 1942 bottom 61 XPol Panel 1710–2170 45° 19.5dBi 0°–8°T 742218V01 1306 bottom 62 XPol Panel 1710–2180 45° 21.5dBi 0°–6°T 742219V01 1946 bottom 62 XPol Panel 1710–2170 65° 9dBi 0°T 742210V01 155 bottom or top 63 XPol Panel 1710–2170 65° 12dBi 2°T 739489V01 342 bottom 63 XPol Panel XPol Panel 1710–2170 1710–2200 65° 65° 16dBi 15.5dBi 0°T 0°–12°T 742196V01 80010247V01 735 735 bottom or top bottom 64 64 XPol Panel 1710–2690 65° 16.5dBi 0°–12°T 80010681 851 bottom 65 XPol XPol XPol XPol XPol XPol XPol XPol Panel Panel Panel Panel Panel Panel Panel Panel 1710–2200 1710–2200 1710–2200 1710–2170 1710–2200 1710–2200 1710–2200 1710–2690 65° 65° 65° 65° 65° 65° 65° 65° 18.3dBi 18.3dBi 18dBi 18dBi 18dBi 18dBi 18dBi 18dBi 0°T 2°T 6°T 0°–8°T 0°–10°T 2°–10°T 0°–15°T 0°–12°T ESLS ESLS ESLS 80010425V01 80010426V01 80010428V01 742214V01 742215V01 80010614V01 80010504V01 80010621V01 1302 1302 1302 1142 1314 1314 1387 1400 bottom bottom bottom bottom bottom bottom bottom bottom 66 66 67 67 68 68 69 70 XPol Panel XPol Panel XPol Panel 1710–2200 1710–2200 1710–2200 65° 65° 62° 19.5dBi 19dBi 19dBi 0°–6°T 0°–10°T 0°–8°T ESLS HE 742213V01 80010505V01 80010636 1954 1984 1407 bottom bottom bottom 71 72 73 XPol Panel XPol Panel XPol Panel 1710–2170 1710–2200 1710–2200 65° 65° 62° 20.5dBi 21dBi 21.2dBi 0°T 0°T 0°–6°T HE HE 742186V01 80010439V01 80010378 2160 2172 2548 bottom bottom or top bottom 73 74 74 XPol Panel 1710–2170 88° 11.5dBi 0°T 741984V01 342 bottom or top 75 XPol Panel 1710–2170 88° 14dBi 0°–10°T 741988V01 662 bottom 75 XPol Panel 1710–2200 88° 17dBi 0°–8°T 741989V01 1302 bottom 76 XPol Panel XPol Panel 1710–1880 1710–2170 90° 88° 17.5dBi 18dBi 2°T 0°–6°T 739710 741990V01 1902 1942 bottom bottom 76 77 Antennas with Dual-Beam XXPol Panel 1710–2200 1710–2200 40° (–30°) 40° (+30°) 17dBi 17dBi 2°–14°T 2°–14°T 80010605 662 bottom 78 XXPol Panel 1710–2200 1710–2200 45° (–30°) 45° (+30°) 19.5dBi 19.5dBi 0°–10°T 0°–10°T 80010606V01 1314 bottom 79 New or changed product Abbreviations: ESLS: Enhanced Side Lobe Suppression (above or below horizon) HE: High Efficiency (Antennas with high gain compared to length) 58 Summary – Directional Antennas Dual Polarization + 45°/ –45° 1800/1900/2000/2600 Antennas with integrated RET Type XPol Panel IRT XPol Panel IRT 1710–2200 1710–2200 65° 65° Type No. Height [mm] Connector position Page 18dBi 0°–10°T 18dBi 0°–10°T 80010314 80010618 1302 1302 bottom bottom 80 80 XPol Tri-Sector Pipe 1710–2170 65° 15.5dBi 0°–12°T 80010375 1241 bottom 81 XPol Tri-Sector Pipe 1710–2170 65° 80010360 1823 bottom 82 Flexible Sealing Frame 18dBi 0°–10°T 85010010 83 Further types on request. Please contact: [email protected] Abbreviations: IRT: Integrated Remote Tilt Unit 59 1800/1900/2000/2600 XPol Tri-Sector Pipe Antenna Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 X 33° XPol Panel 1710–2170 33° 20dBi 0°–12°T 80010251V01 Type No. 1710 – 1880 MHz +45°, –45° 2 x 19.2 dBi 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 19.5 dBi 1920 – 2170 MHz +45°, –45° 2 x 19.8 dBi 36° > 30 dB 35° > 30 dB 33° > 30 dB Typically: 25 dB > 10 dB > 18 dB Typically: 25 dB > 10 dB > 17 dB 1.0 dB ±1.0° Typically: 25 dB > 10 dB > 15 dB 1800/1900/2000/2600 XPol Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180° ± 30°) Cross polar ratio Maindirection 0° Sector ±30° Sidelobe suppression Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 9.2° 9° 8.5° 0°– 12°, continuously adjustable 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 6° ... 12° T 15 ... 17 … 17 dB 15 ... 17 ... 17 dB 15 ... 17 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 420 / 110 / 520 N 1032 / 299 / 69 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2170 33° 21dBi 0°–8°T 742351V01 Type No. 1710 – 1880 MHz +45°, –45° 2 x 20.2 dBi 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 20.5 dBi 1920 – 2170 MHz +45°, –45° 2 x 20.7 dBi 36° > 30 dB 35° > 30 dB 33° > 30 dB Typically: 20 dB > 10 dB > 14 dB Typically: 20 dB > 10 dB > 14 dB 0.5 dB ±1.0° Typically: 20 dB > 10 dB > 14 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±30° Sidelobe suppression Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 60 s clamp d e includ 7.4° 7.0° 6.7° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 18 ... 17 … 16 dB 18 ... 18 ... 17 dB 18 ... 17 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 540 / 135 / 640 N 1304 / 299 / 69 mm M (Medium) 13.5 kg / 15.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 1710–1880 X 33° XPol Panel 1710–1880 33° 22dBi 2°T 741623 Type No. Frequency range 1710 – 1880 MHz Polarization +45°, –45° Gain Electrical tilt Sidelobe suppression 2 x 22 dBi +45° Horizontal: Vertical: –45° Horizontal: Vertical: 33° 5° 2°, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain Front-to-back ratio, copolar > 30 dB Isolation > 30 dB VSWR 33° 5° < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 200 W (at 50 °C ambient temperature) Input Connector position Weight Wind load (at 150 km/h) Height/width/depth 1800/1900/2000/2600 XPol Half-power beam width Copolar 2 x 7-16 female Bottom 11 kg Frontal / lateral / rearside: 540 / 210 / 770 N 1942 / 262 / 59 mm For more information about additional mounting accessories please refer to page 186 61 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2180 X 45° XPol Panel 1710–2170 45° 19.5dBi 0°–8°T 742218V01 Type No. Frequency range 1800/1900/2000/2600 XPol 1710 – 1880 MHz +45°, –45° 2 x 19 dBi s clamp d e includ 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 19.5 dBi 1920 – 2170 MHz Polarization +45°, –45° Gain 2 x 19.6 dBi Horizontal Pattern: Half-power beam width 47° 45° 44° Front-to-back ratio Copolar: > 27 dB Copolar: > 30 dB Copolar: > 27 dB (180° ± 30°) Total power: > 25 dB Total power: > 25 dB Total power: > 25 dB Cross polar ratio Maindirection 0° Typically: 18 dB Typically: 18 dB Typically: 18 dB Sector ±30° > 13 dB > 13 dB > 13 dB Sidelobe suppression > 18 dB > 18 dB > 18 dB Tracking, Avg. 0.5 dB Squint ±1.5° Vertical Pattern: Half-power beam width 7.3° 7° 6.7° Electrical tilt 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° T sidelobe above main beam 17 ... 17 ... 15 ... 15 dB 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 15 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside 450 / 145 / 490 N 1306 / 199 / 69 mm M (Medium) 10.5 kg / 12.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2180 45° 21.5dBi 0°–6°T 742219V01 Type No. Frequency range 1710 – 1880 MHz +45°, –45° 20.5 ... 20.6 ... 20.3 0° ... 3° ... 6° s clamp d e includ 1710–2170 1850 – 1990 MHz +45°, –45° 20.9 ... 21.1 ... 20.9 0° ... 3° ... 6° 1920 – 2180 MHz Polarization +45°, –45° Average gain (dBi) 21 ... 21.4 ... 21 Tilt 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 48° 45° 44° Front-to-back ratio Copolar: > 28 dB Copolar: > 27 dB Copolar: > 25 dB (180°±30°) Total power: > 25 dB Total power: > 25 dB Total power: > 25 dB Cross polar ratio Maindirection 0° Typically: 19 dB Typically: 18 dB Typically: 17 dB Sector ±30° > 13 dB > 13 dB > 13 dB Sidelobe supression > 18 dB > 18 dB > 18 dB Tracking, Avg. 1.0 dB Squint ±2.0° Vertical Pattern: Half-power beam width 4.7° 4.5° 4.4° Electrical tilt 0°– 6°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T sidelobe above main beam 18 ... 18 ... 16 ... 16 dB 18 ... 18 ... 17 ... 16 dB 18 ... 18 ... 17 ... 16 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 62 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 700 / 220 / 740 N 1946 / 199 / 69 mm M (Medium) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 X 65° XPol Panel 1710–2170 65° 9dBi 0°T 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 8.6 dBi 1920 – 2170 MHz +45°, –45° 2 x 8.7 dBi 70° > 25 dB 68° > 30 dB 65° > 30 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 1.0 dB ±3.0° Typically: 25 dB > 10 dB 65° 0°, fixed 65° 0°, fixed 63° 0°, fixed VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1800/1900/2000/2600 XPol 1710 – 1880 MHz +45°, –45° 2 x 8.5 dBi Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt s clamp d e includ 742210V01 Type No. < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 50 / 13 / 55 N 155 / 155 / 69 mm L (Light) 1.5 kg / 1.7 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter XPol Panel 1710–2170 65° 12dBi 2°T 1710 – 1880 MHz +45°, –45° 2 x 11.5 dBi 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 12 dBi 1920 – 2170 MHz +45°, –45° 2 x 12 dBi 67° > 30 dB 65° > 30 dB 63° > 27 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±1.5° Typically: 25 dB > 10 dB 32° 3°, fixed 30° 2°, fixed 28° 0°, fixed Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-powr beam width Electrical tilt VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 739489V01 Type No. < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 90 / 27 / 105 N 342 / 155 / 69 mm L (Light) 2.2 kg / 2.4 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 186 63 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2170 65° 16dBi 0°T s clamp d e includ 742196V01 Type No. 1710 – 1880 MHz 1710–2170 1850 – 1990 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 15.3 dBi 2 x 15.6 dBi 2 x 15.8 dBi Frequency range 1920 – 2170 MHz Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection Sector 0° ±60° 67° 66° 64° Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 1800/1900/2000/2600 XPol Tracking, Avg. 0.5 dB Squint ±1.5° Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon 12.6° 11.8° 11° > 14 dB > 16 dB > 14 dB VSWR < 1.4 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Wind load (at 150 km/h) Bottom or top Frontal: / lateral / rearside: 85 / 65 / 220 N Height/width/depth 735 / 155 / 69 mm Category of mounting hardware L (Light) Weight Scope of supply 4.5 kg / 4.7 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter XPol Panel 1710–2200 65° 15.5dBi 0°–12°T Frequency range Polarization Gain per input Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Isolation, between ports VSWR Intermodulation IM3 Max. power per input Input Connector position s clamp d e includ 80010247V01 Type No. 1710 – 1880 MHz +45°, –45° 0° ... 4° ... 8° ... 12° T 15.5 ... 15.4 ... 15.3 ...15.1 dBi 1710–2200 1850 – 1990 MHz +45°, –45° 0° ... 4° ... 8° ... 12° T 15.6 ... 15.5 ... 15.4 ...15 dBi 67° Copolar: > 27 dB 66° Copolar: > 27 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB 0.5 dB ±2.0° 1920 – 2200 MHz +45°, –45° 0° ... 4° ... 8° ... 12° T 15.8 ... 15.7 ... 15.5 ...14.9 dBi 64° Copolar: > 27 dB Typically: 20 dB > 10 dB 12.9° 12.3° 11.5° 0°– 12°, continuously adjustable 0° ... 4° ... 8° ... 12° T 0° ... 4° ... 8° ... 12° T 0° ... 4° ... 8° ... 12° T > 14 ... 14 ... 14 ... 14 dB > 14 ... 14 ... 14 ... 14 dB > 14 ... 14 ... 14 ... 14 dB > 30 dB < 1.4 < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Adjustment mechanism 1x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 195 / 70 / 220 N Height/width/depth Category of mounting hardware Weight Scope of supply 64 735 / 155 / 69 mm L (Light) 4.5 kg / 4.7 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2690 X 65° XPol Panel 1710–2690 65° 16.5dBi 0°–12°T s clamp d e includ 80010681 Type No. Frequency range 1710 – 1990 MHz 1710–2690 1920 – 2200 MHz 2200 – 2490 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain at 0° tilt 2 x 15.5 dBi 2 x 16.3 dBi 2 x 16.7 dBi 2 x 16.7 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±30°) Cross polar ratio Sector 0° ±60° 67° 64° 60° 60° > 25 dB > 25 dB > 23 dB > 23 dB Typically: 25 dB > 9 dB Typically: 28 dB > 8 dB Typically: 28 dB > 8 dB Typically: 28 dB > 11 dB 9.9° 8.8° 8.4° Half-power beam width 10.8° Electrical tilt Sidelobe suppression – for first sidelobe above main beam VSWR Isolation, between ports 0°– 12°, continuously adjustable 0° ... 6° ... 12° T ≥ 12 ... 13 ... 15 dB 0° ... 6° ... 12° T ≥ 13 ... 14 ... 15 dB 0° ... 6° ... 12° T ≥ 13 ... 14 ... 16 dB < 1.5 < –150 dBc (2 x 43 dBm carrier) Max. power per input 250 W (at 50 °C ambient temperature) Connector position 2 x 7-16 female Bottom Adjustment mechanism 1 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 210 / 60 / 220 N Height/width/depth Category of mounting hardware Weight Scope of supply 0° ... 6° ... 12° T ≥ 15 ... 15 ... 17 dB > 30 dB Intermodulation IM3 Input 1800/1900/2000/2600 XPol Vertical Pattern: 851 / 155 / 70 mm L (Light) 5 kg / 5.2 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 186 65 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 18.3dBi 0°T s clamp d e includ 80010425V01 Type No. 1710 – 1880 MHz 1710–2200 1850 – 1990 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 17.9 dBi 2 x 18.1 dBi 2 x 18.3 dBi Frequency range 1920 – 2200 MHz Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Sector 0° ±60° 67° 66° 64° > 30 dB > 30 dB > 30 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Tracking, Avg. 0.5 dB 1800/1900/2000/2600 XPol Squint ±1.5° Vertical Pattern: Half-power beam width 6.6° 6.2° 5.8° Electrical tilt 0°, fixed 0°, fixed 0°, fixed Sidelobe suppression for first sidelobe above main beam > 14 dB > 15 dB > 16 dB First null-fill below main beam Typically: 25 dB Typically: 25 dB Typically: 25 dB VSWR < 1.4 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Bottom Wind load (at 150 km/h) Frontal / lateral / rearside: 330 / 115 / 390 N Height/width/depth 1302 / 155 / 69 mm Category of mounting hardware M (Medium) Weight 7 kg / 9 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2200 65° 18.3dBi 2°T s clamp d e includ 80010426V01 Type No. 1710 – 1880 MHz 1710–2200 1850 – 1990 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 17.9 dBi 2 x 18.1 dBi 2 x 18.3 dBi Frequency range 1920 – 2200 MHz Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Sector 0° ±60° 66° 65° 63° > 28 dB > 30 dB > 33 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±1.5° Vertical Pattern: Half-power beam width 6.6° 6.2° 5.8° Electrical tilt 2°, fixed 2°, fixed 2°, fixed Sidelobe suppression for first sidelobe above main beam > 14 dB > 15 dB > 15 dB First null-fill below main beam Typically: 25 dB Typically: 25 dB Typically: 25 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 66 < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 330 / 115 / 390 N 1302 / 155 / 69 mm M (Medium) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 18dBi 6°T s clamp d e includ 80010428V01 Type No. Frequency range 1710 – 1880 MHz 1710–2200 1850 – 1990 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 17.7 dBi 2 x 17.9 dBi 2 x 18.1 dBi 1920 – 2200 MHz Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Sector 0° ±60° 67° 65° 63° > 27 dB > 33 dB > 33 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±1.5° Half-power beam width 6.7° 6.3° 5.8° Electrical tilt 6°, fixed 6°, fixed 6°, fixed Sidelobe suppression for first sidelobe above main beam > 14 dB > 14 dB > 15 dB First null-fill below main beam Typically: 25 dB Typically: 25 dB Typically: 25 dB VSWR < 1.3 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 2 x 7-16 female Connector position Bottom Wind load (at 150 km/h) Frontal / lateral / rearside: 330 / 115 / 390 N Height/width/depth 1302 / 155 / 69 mm Category of mounting hardware M (Medium) Weight Scope of supply 1800/1900/2000/2600 XPol Vertical Pattern: 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 1710–2170 65° 18dBi 0°–8°T 1710 – 1880 MHz +45°, –45° 2 x 17.5 dBi 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 17.7 dBi 1920 – 2170 MHz +45°, –45° 2 x 18 dBi 66° Copolar: 30 dB 64° Copolar: 30 dB 62° Copolar: 30 dB Avg.: 25 dB > 10 dB Avg.: 25 dB > 10 dB 1 dB ±2.5° Avg.: 28 dB > 10 dB Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon, Avg. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamp d e includ 742214V01 Type No. 8.3° 7.8° 7.4° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 20 ... 20 ... 20 dB 20 ... 20 ... 20 dB 20 ... 20 ... 20 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 290 / 80 / 300 N 1142 / 155 / 70 mm L (Light) 5 kg / 7 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 67 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 18dBi 0°–10°T 1710 – 1880 MHz +45°, –45° 2 x 17.7 dBi 1710–2200 1850 – 1990 MHz +45°, –45° 2 x 17.9 dBi 1920 – 2200 MHz +45°, –45° 2 x 18 dBi 68° Copolar: > 30 dB Total power: > 25 dB 66° Copolar: > 30 dB Total power: > 25 dB 64° Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±1.5° Typically: 25 dB > 10 dB Frequency range 1800/1900/2000/2600 XPol s clamp d e includ 742215V01 Type No. Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 6.8° 6.4° 0°– 10°, continuously adjustable 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 17 ... 17 dB Isolation, between ports VSWR Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply > 30 dB < 1.5 < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 330 / 90 / 340 N 1314 / 155 / 70 mm L (Light) 6.5 kg / 8.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 7.1° XPol Panel 1710–2200 65° 18dBi 2°–10°T ESLS Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Sidelobe suppression in the sector 40°–180° below horizon for Tx-Frequencies VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 68 s clamp d e includ 80010614V01 Type No. 1710 – 1880 MHz +45°, –45° 2 x 17.3 dBi 1710–2200 1850 – 1990 MHz +45°, –45° 2 x 17.7 dBi 1920 – 2200 MHz +45°, –45° 2 x 18 dBi 66° ≥ 25 dB 25 dB ≥ 10 dB 64° ≥ 25 dB 25 dB ≥ 10 dB 0.5 dB ±1.5° 62° ≥ 25 dB 25 dB ≥ 10 dB 7.9° 7.5° 2°– 10°, continuously adjustable 7.2° > 15 dB > 17 dB > 18 dB > 23 dB > 24 dB > 25 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 330 / 90 / 340 N 1314 / 155 / 70 mm L (Light) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 18dBi 0°–15°T ESLS 80010504V01 Frequency range 1710 – 1880 MHz +45°, –45° 2 x 17.5 dBi s clamp d e includ 1710–2200 1850 – 1990 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 17.6 dBi 2 x 17.7 dBi 2000 – 2200 MHz Polarization +45°, –45° Gain at 0° tilt 2 x 17.8 dBi Horizontal Pattern: Half-power beam width 68° 66° 64° 62° Front-to-back ratio (180° ±30°) ≥ 25 dB ≥ 25 dB ≥ 25 dB ≥ 25 dB Cross polar ratio 0° 22 dB 22 dB 24 dB 26 dB Sector ±60° ≥ 10 dB ≥ 10 dB ≥ 10 dB ≥ 10 dB Tracking, Avg. 1.0 dB Squint ±2.0° Vertical Pattern: Half-power beam width 7.9° 7.5° 7.2° 7.0° Electrical tilt 0°– 15°, continuously adjustable Sidelobe suppression 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T – for first sidelobe above main beam ≥ 17 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 17 dB ≥ 15 ... 20 ... 18 ... 15 dB – within 0°–20° sector above horizon ≥ 16 ... 18 ... 18 ... 16 dB ≥ 16 ... 18 ... 17 ... 16 dB ≥ 15 ... 18 ... 17 ... 16 dB ≥ 15 ... 16 ... 16 ... 15 dB Null-fill at 0° tilt 21 dB 20 dB 19 dB 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 360 / 100 / 370 N 1387 / 155 / 69 mm L (Light) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 69 1800/1900/2000/2600 XPol Type No. Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2690 X 65° XPol Panel 1710–2690 65° 18dBi 0°–12°T ESLS 80010621V01 Type No. Frequency range 1710–2690 1920 – 2200 MHz 2200 – 2490 MHz 1710 – 1990 MHz Polarization Gain (dBi) Tilt s clamp d e d lu c in 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 17.4 ... 17.4 ... 17.3 0° ... 6° ... 12° 18.2 ... 18.0 ... 17.9 0° ... 6° ... 12° 18.2 ... 18.1 ... 17.7 0° ... 6° ... 12° 18.3 ... 18.0 ... 17.6 0° ... 6° ... 12° Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) 1800/1900/2000/2600 XPol Cross polar ratio Sector 0° ±60° 68° 64° 61° 60° > 25 dB > 25 dB > 25 dB > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 5.9° 5.7° Tracking, Avg. 1.0 dB Squint ±2.5° Vertical Pattern: Half-power beam width 7.1° 6.5° Electrical tilt Sidelobe suppression – for first sidelobe above main beam – within 0°–20° sector above horizon VSWR Isolation, between ports 0°– 12°, continuously adjustable 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 17 ... 17 ... 16 dB 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 17 ... 17 ... 16 dB 0° ... 6° ... 12° T ≥ 18 ... 17 ... 17 dB ≥ 16 ... 18 ... 17 dB < 1.5 > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input Connector position 2 x 7-16 female Bottom Adjustment mechanism 1x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 370 / 135 / 420 N Height/width/depth Category of mounting hardware Weight Scope of supply 70 0° ... 6° ... 12° T ≥ 18 ... 18 ... 16 dB ≥ 15 ... 15 ... 14 dB 1400 / 155 / 70 mm M (Medium) 8 kg / 10 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 19.5dBi 0°–6°T s clamp d e includ 742213V01 Type No. Frequency range 1710 – 1880 MHz 1710–2200 1850 – 1990 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 19 dBi 2 x 19.2 dBi 2 x 19.5 dBi 1920 – 2200 MHz Half-power beam width Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection Sector 0° ±60° 67° 65° 63° Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Tracking, Avg. 1800/1900/2000/2600 XPol Horizontal Pattern: 0.5 dB Squint ±2° Vertical Pattern: Half-power beam width Electrical tilt 4.7° 4.5° Sidelobe suppression for first 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T sidelobe above main beam 18 ... 18 ... 16 .... 15 dB 18 ... 18 ... 17 ... 16 dB Isolation, between ports VSWR 4.3° 0°– 6°, continuously adjustable 0° ... 2° ... 4° ... 6° T 18 ... 18 ... 18 ... 18 dB > 30 dB < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input Connector position 2 x 7-16 female Bottom Adjustment mechanism 1x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 510 / 140 / 510 N Height/width/depth Category of mounting hardware Weight Scope of supply 1954 / 155 / 70 mm M (Medium) 9 kg / 11 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 71 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 19dBi 0°–10°T ESLS Type No. 1800/1900/2000/2600 XPol Frequency range 80010505V01 s clamp d e includ 1710–2200 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2000 – 2200 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 18.5 ... 18.7 ... 18.5 dB 18.7 ... 19.0 ... 18.5 dB 18.7 ... 19.0 ... 18.4 dB 18.7 ... 18.9 ... 18.3 dB 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T Polarization Average Gain (dBi) Tilt Horizontal Pattern: Half-power beam width 67° 65° 64° 63° Front-to-back ratio (180° ±30°) ≥ 30 dB ≥ 30 dB ≥ 27 dB ≥ 26 dB Cross polar ratio 0° Typically: 25 dB Typically: 22 dB Typically: 22 dB Typically: 22 dB Sector ±60° ≥ 11 dB ≥ 11 dB ≥ 11 dB ≥ 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 5.0° 4.8° 4.6° 4.4° Electrical tilt 0°– 10°, continuously adjustable Sidelobe suppression 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T – for first sidelobe above main beam ≥ 20 ... 20 ... 18 ... 18 dB ≥ 20 ... 20 ... 18 ... 18 dB ≥ 19 ... 20 ... 18 ... 18 dB ≥ 18 ... 20 ... 18 ... 18 dB – within 0°–20° sector above horizon ≥ 18 ... 18 ... 17 ... 17 dB ≥ 17 ... 18 ... 17 ... 15 dB ≥ 17 ... 17 ... 17 ... 15 dB ≥ 17 ... 17 ... 14 ... 12 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 72 < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom continuously adjustable Frontal / lateral / rearside: 520 / 190 / 630 N 1984 / 155 / 69 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 62° 19dBi 0°–8°T s clamp d e includ 80010636 Type No. 1710 – 1880 MHz +45°, –45° 2 x 18.3 dBi 1710–2200 1850 – 1990 MHz +45°, –45° 2 x 18.7 dBi 1920 – 2200 MHz +45°, –45° 2 x 19 dBi 65° > 30 dB 62° > 30 dB 59° > 28 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±1.5° Typically: 25 dB > 10 dB Frequency range VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 6.6° 6.2° 5.9° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 18 ... 14 ... 14 dB 18 ... 15 ... 15 dB 18 ... 15 ... 15 dB 1800/1900/2000/2600 XPol Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°± 30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 360 / 100 / 370 N 1407 / 155 / 70 mm L (Light) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2170 65° 20.5dBi 0°T s clamp d e includ 742186V01 Type No. 1710 – 1880 MHz 1710–2170 1850 – 1990 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° +45°, –45° 20 dBi 20.2 dBi 20.5 dBi 67° 65° 61° Copolar: > 30 dB Total power: > 28 dB Copolar: > 30 dB Total power: > 28 dB Copolar: > 30 dB Total power: > 27 dB Typically: 25 dB > 14 dB Typically: 25 dB > 14 dB Typically: 25 dB > 14 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection Sector 0° ±60° Tracking, Avg. 0.5 dB Squint ±1.0° Vertical Pattern: Half-power beam width VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 4° 3.8° 3.5° < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 580 / 200 / 670 N 2160 / 155 / 69 mm M (Medium) 9.5 kg / 11.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 73 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel 1710–2200 65° 21dBi 0°T Frequency range 1800/1900/2000/2600 XPol s clamp d e includ 80010439V01 Type No. Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression – for first sidelobe above main beam – within 0°–30° sector above horizon First null-fill below main beam 1710–2200 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2000 – 2200 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 2 x 20.5 dBi 2 x 20.8 dBi 2 x 21.1 dBi 2 x 21.2 dBi 66° > 30 dB 25 dB > 12 dB 63° > 30 dB 23 dB > 12 dB 60° > 30 dB 23 dB > 10 dB 58° > 30 dB 23 dB > 10 dB 3.7° 3.5° 0.5 dB ±1.0° 4.2° 4° 0°, fixed > 15 dB > 15 dB < 20 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 550 / 210 / 610 N 2172 / 155 / 89 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2200 62° 21.2dBi 0°–6°T 80010378 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°± 30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Null-fill at 0° tilt VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 74 1710 – 1880 MHz +45°, –45° 2 x 20.6 dBi 65° > 30 dB 25 dB > 10 dB 1710–2200 1850 – 1990 MHz +45°, –45° 2 x 21.1 dBi 62° > 28 dB 23 dB > 10 dB 1.0dB ±2.5° s clamp d e includ 1920 – 2200 MHz +45°, –45° 2 x 21.2 dBi 60° > 28 dB 23 dB > 10 dB 3.7° 3.5° 3.3° 0°– 6°, continuously adjustable 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 18 ... 18 ... 17 dB 18 ... 17 ... 17 dB 17 ... 17 ... 17 dB 20 dB 20 dB 20 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 660 / 260 / 730 N 2548 / 155 / 89 mm M (Medium) 13 kg / 15 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 X 88° XPol Panel 1710–2170 88° 11.5dBi 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 11.5 dBi 1920 – 2170 MHz +45°, –45° 2 x 11.6 dBi 86° Copolar: > 23 dB Total power: > 23 dB 87° Copolar: > 23 dB Total power: > 23 dB 88° Copolar: > 23 dB Total power: > 23 dB Typically: 20 dB > 18 dB Typically: 25 dB > 18 dB 0.5 dB ±3.0° Typically: 20 dB > 15 dB 28° 26° 26° > 20 dB > 20 dB > 20 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1800/1900/2000/2600 XPol 1710 – 1880 MHz +45°, –45° 2 x 11.3 dBi Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression vertical sector ±45° s clamp d e includ 741984V01 Type No. < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 90 / 27 / 105 N 342 / 155 / 69 mm L (Light) 2 kg / 2.2 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter XPol Panel 1710–2170 88° 14dBi 0°–10°T 741988V01 Type No. Frequency range 1710 – 1880 MHz +45°, –45° 2 x 13.7 dBi s clamp d e includ 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 14 dBi 1920 – 2170 MHz Polarization +45°, –45° Gain 2 x 14.1 dBi Horizontal Pattern: Half-power beam width 88° 88° 88° Front-to-back ratio, copolar > 25 dB > 25 dB > 25 dB total power > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection 0° Typically: 20 dB Typically: 20 dB Typically: 20 dB Sector ±60° > 10 dB > 10 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±3.5° Vertical Pattern: Half-power beam width 14.7° 14° 13° Electrical tilt 0° – 10°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T sidelobe above main beam 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 175 / 65 / 200 N 662 / 155 / 69 mm L (Light) 4.2 kg / 4.4 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 186 75 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 88° XPol Panel 1710–2200 88° 17dBi 0°–8°T 741989V01 Type No. 1710–2200 1850 – 1990 MHz +45°, –45° 2 x 16.8 dBi Frequency range 1710 – 1880 MHz +45°, –45° 2 x 16.5 dBi 1800/1900/2000/2600 XPol s clamp d e includ 1920 – 2200 MHz Polarization +45°, –45° Gain 2 x 16.7 dBi Horizontal Pattern: Half-power beam width 88° 88° 88° Front-to-back ratio Copolar: > 25 dB Copolar: > 25 dB Copolar: > 24 dB (180° ± 30°) Total power: > 25 dB Total power: > 25 dB Total power: > 24 dB Cross polar ratio Maindirection 0° Typically: 20 dB Typically: 20 dB Typically: 20 dB Sector ±60° > 10 dB > 10 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±2.0° Vertical Pattern: Half-power beam width 7° 6.7° 6.5° Electrical tilt 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° T sidelobe above main beam 18 ... 18 ... 16 .... 14 dB 20 ... 20 ... 18 ... 17 dB 18 ... 18 ... 18 ... 17 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottomcontinuously adjustable Frontal / lateral / rearside: 350 / 125 / 400 N 1302 / 155 / 69 mm M (Medium) 7.5 kg / 9.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–1880 90° 17.5dBi 2°T Type No. Frequency range 739710 1710 – 1880 MHz Polarization +45°, –45° Gain 2 x 17.5 dBi Half-power beam width Copolar +45°/ –45° Horizontal: Vertical: Electrical tilt 2°, fixed Sidelobe suppression for first sidelobe above horizon ≥ 14 dB Front-to-back ratio, copolar > 25 dB Isolation, between ports > 30 dB VSWR 90° 5° < 1.4 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 200 W (at 50 °C ambient temperature) Input Connector position Weight Wind load (at 150 km/h) Height/width/depth 76 2 x 7-16 female Bottom 9 kg Frontal / lateral / rearside: 530 / 150 / 610 N 1902 / 155 / 69 mm For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 X 88° XPol Panel 1710–2170 88° 18dBi 0°–6°T 741990V01 Type No. Frequency range 1710–2170 1850 – 1990 MHz +45°, –45° 2 x 18 dBi 1920 – 2170 MHz Polarization +45°, –45° Gain 2 x 18.2 dBi Horizontal Pattern: Half-power beam width 88° 88° 88° Front-to-back ratio, copolar > 25 dB > 25 dB > 25 dB total power > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection 0° Typically: 20 dB Typically: 20 dB Typically: 20 dB Sector ±60° > 10 dB > 10 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 4.9° 4.7° 4.5° Electrical tilt 0°– 6°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T sidelobe above main beam 17 ... 17 ... 17 ...17 dB 18 ... 18 ... 18 ...18 dB 18 ... 18 ... 18 ...18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1800/1900/2000/2600 XPol 1710 – 1880 MHz +45°, –45° 2 x 17.7 dBi s clamp d e includ < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable Frontal / lateral / rearside: 510 / 185 / 610 N 1942 / 155 / 69 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 77 Dual-Beam Panel Dual Polarization Half-power Beam Width 1710 –2200 1710 –2200 X X 40° 40° XXPol Panel 1710–2200/1710–2200 40°(–30°)/40°(+30°) 17/17dBi 2°–14°/2°–14°T 80010605 Type No. Frequency range 1710–2200 1850 – 1990 MHz 1920 – 2200 MHz Beam A (–30°), Beam B (+30°) +45°, –45°, +45°, –45° +45°, –45°, +45°, –45° +45°, –45°, +45°, –45° 4 x 16 dBi 4 x 16.8 dBi 4 x 17 dBi 1710 – 1880 MHz Cross polar ratio Maindirection –30°; +30° Sector –60°; 0°; 0°; +60° Sidelobe suppression for sidelobes beside main beam Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between inputs Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight (approx.) Scope of supply 43° 39° 36° Copolar: > 30 dB Total power: > 25 dB Typically: 15 dB > 10 dB Typically: 15 dB > 10 dB > 18 dB Typically: 15 dB > 10 dB 14.5° 14° 2°–14°, continuously adjustable 13° > 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom Frontal / lateral / rearside: 420 / 110 / 480 N 662 / 380 / 150 mm M (Medium) 16 kg / 18 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Dual Beam Antenna Patterns: 1710 – 1880 MHz 43° Beam A (–30°) 14.5° 10 43° Beam B (+30°) Horizontal Pattern dB dB 3 10 3 Vertical Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt 1850 – 1990 MHz 39° Beam A (–30°) 1710 – 2200 +45° Beam B (+30°) 1710 – 2200 +45° Beam A (–30°) 1710–2200 –45° Beam A (–30°) 7-16 7-16 7-16 7-16 10 39° Beam B (+30°) Horizontal Pattern dB dB 3 1710 – 2200 –45° Beam B (+30°) 14° 10 3 Vertical Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt 1920 – 2200 MHz 36° Beam A (–30°) 10 36° Horizontal Pattern 78 Beam B (+30°) dB 3 13° 10 dB 1800/1900/2000/2600 XPol Azimuth direction Polarization Gain Horizontal Pattern: Half-power beam width (offset beams ±30°) Front-to-back ratio 3 Vertical Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt For more information about additional mounting accessories please refer to page 186 Dual-Beam Panel Dual Polarization Half-power Beam Width 1710 –2200 1710 –2200 X X 45° 45° XXPol Panel 1710–2200/1710–2200 45°(–30°)/45°(+30°) 19.5/19.5dBi 0°–10°/0°–10°T s clamp d e d lu c in 80010606V01 Type No. Frequency range 1710–2200 1850 – 1990 MHz 1920 – 2200 MHz Beam A (–30°), Beam B (+30°) +45°, –45°, +45°, –45° +45°, –45°, +45°, –45° +45°, –45°, +45°, –45° 4 x 19 dBi 4 x 19.3 dBi 4 x 19.5 dBi 1710 – 1880 MHz Cross polar ratio Maindirection –30°; +30° Sector –60°; 0°; 0°; +60° Sidelobe suppression for sidelobes beside main beam Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between inputs Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 47° 45° 43° Copolar: > 30 dB Total power: > 25 dB Typically: 18 dB > 13 dB Typically: 17 dB > 13 dB > 18 dB Typically: 16 dB > 13 dB 7.2° 7.1° 0°–10°, continuously adjustable 6.8° 1800/1900/2000/2600 XPol Azimuth direction Polarization Gain Horizontal Pattern: Half-power beam width (offset beams ±30°) Front-to-back ratio > 18 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom Frontal / lateral / rearside: 710 / 200 / 820 N 1314 / 380 / 150 mm M (Medium) 18.5 kg / 20.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter Dual Beam Antenna Patterns: 1710 – 1880 MHz 47° Beam A (–30°) 7.2° 10 47° Horizontal Pattern 3 dB dB 3 10 Beam B (+30°) Vertical Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt 1850 – 1990 MHz 45° 1710 – 2200 –45° Beam B (+30°) 1710 – 2200 +45° Beam B (+30°) 1710 – 2200 +45° Beam A (–30°) 1710–2200 –45° Beam A (–30°) 7-16 7-16 7-16 7-16 Beam A (–30°) 7.1° 10 45° Horizontal Pattern 3 dB dB 3 10 Beam B (+30°) Vertical Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt 1920 – 2200 MHz 43° Beam A (–30°) 6.8° 10 43° Horizontal Pattern 3 dB dB 3 10 Beam B (+30°) Vertical Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt For more information about additional mounting accessories please refer to page 186 79 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 X 65° XPol Panel IRT 1710–2200 65° 18dBi 0°–10°T 80010314 / 80010618 Type No. A) Antenna specifications 1710 – 1880 MHz 1710–2200 1850 – 1990 MHz 1920 – 2200 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Gain 2 x 17.7 dBi 2 x 17.9 dBi 2 x 18 dBi Frequency range Horizontal Pattern: Half-power beam width 1800/1900/2000/2600 XPol Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 67° 66° 65° Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 6.8° 6.6° Vertical Pattern: Half-power beam width 7.1° Electrical tilt 0°– 10°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T sidelobe above main beam 16 ... 16 ... 16 ... 16 dB 17 ... 17 ... 17 ... 17 dB 17 ... 17 ... 17 ... 17 dB VSWR < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 120 W (at 50 °C ambient temperature) Input 2 x 7-16 female IRT in: 1 x 8pin male IRT out: 1 x 8pin female Connector position Bottom Wind load(at 150 km/h) Frontal / lateral / rearside: 330 / 115 / 390 N Height/width/depth 1302 / 155 / 69 mm ) M (Medium Category of mounting hardware Weight 7.5 kg B) IRT specifications Logical interface ex factory 1) 80010314 80010618 AISG 1.1 3GPP/AISG 2.0 Protocols Compliant to AISG 1.1 and 3GPP/AISG 2.0 Hardware interface2) 2 x 8pin connector acc. IEC 60130-9; according to AISG: – IRT in (male): Control / Daisy chain in – IRT out (female): Daisy chain out Power supply Power consumption Adjustment time (full range) Adjustment cycles 1710 – 2200 +45° 7-16 7-16 in IRT out 8pin 8pin male female 10 ... 30 V < 1 W (stand by) < 8.5 W (motor activated) 40 sec. > 50,000 1) The protocol of the logical interface can be switched from AISG 1.1 to 3GPP/AISG 2.0 and vice versa with a vendor specific command. Start-up operation of the 80010314 is only possible with a primary station supporting AISG 1.1 and start-up operation of the 80010618 is only possible with a primary station supporting 3GPP/AISG 2.0! Please note: The used Primary-SW has to be able to handle also integrated remote tilt units, like Kathrein CCU with firmware 1.29 or higher and the Kathrein PCA with SW 2.0 or higher. If the Primary of the system doesn’t support the standard of the ‘logical interface ex factory’, the IRT must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information. 2) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handtightened’). The connector should be tightened by hand only! 80 1710 – 2200 –45° For more information about additional mounting accessories please refer to page 186 0° Tri-Sector Pipe Antenna 1710 –2170 Frequency Range X Dual Polarization 65° Half-power Beam Width Adjust. Electr. Downtilt 0°– 12° 120° 240° 1710 –2170 1710 –2170 X X 65° 65° 0°– 12° 0°– 12° set by hand or by optional RCUs (Remote Control Units) XPol Tri-Sector Pipe 1710–2170 65° 15.5dBi 0°–12°T Electrical datas per sector 80010375 1710 – 1880 MHz 1710–2170 1850 – 1990 MHz +45°, –45° +45°, –45° +45°, –45° 0° ... 4° ... 8° … 12° T 15.4 ... 15.2 ... 15.0 ... 14.8 0° ... 4° ... 8° … 12° T 15.5 ... 15.4 ... 15.3 ... 14.9 0° ... 4° ... 8° … 12° T 15.7 ... 15.6 ... 15.4 ... 14.9 Polarization Gain per Input (dBi) Half-power beam width Copolar +45°/ –45° Horizontal: 67° Vertical: 12.7° Electrical tilt continuously adjustable 0°– 12° Sidelobe suppression for first sidelobe above horizon 65° 12° Horizontal: 62° Vertical: 11.2° 0°– 12° 0°– 12° 0° ... 4° ... 8° … 12° T 0° ... 4° ... 8° … 12° T 0° ... 4° ... 8° … 12° T 16 ... 16 ... 15 ... 15 dB 18 ... 17 ... 17 ... 16 dB 18 ... 18 ... 16 ... 16 dB Front-to-back ratio Cross polar ratio Maindirection Sector Horizontal: Vertical: 1920 – 2170 MHz 0° ±60° Copolar: > 25 dB Copolar: > 25 dB Copolar: > 25 dB Typically: 20 dB Typically: > 10 dB Typically: 20 dB Typically: > 10 dB Typically: 20 dB Typically: > 10 dB > 30 dB > 40 dB > 30 dB > 40 dB > 30 dB > 40 dB Isolation: Intrasystem Isolation: Intersystem 1800/1900/2000/2600 XPol Frequency range Impedance 50 Ω 50 Ω 50 Ω VSWR < 1.5 < 1.5 < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 250 W (at 50 °C ambient temperature) compact service area Type No. 0° 7-16 +45° 7-16 Mechanical specifications –45° Input 1710 –2170 Connector position 7-16 –45° 1710 –2170 +45° 240° 7-16 +45° 7-16 1710 –2170 –45° Adjustment mechanism 120° 7-16 Weight Wind load 3 x 2 x 7-16 female Bottom – inside service area 3 x 1, Position bottom continuously adjustable inside service area 32 kg 205 N (at 150 km/h) Max. wind velocity 200 km/h Natural frequency 45 – 47 Hz Damping ratio Mechanical interface Packing size Height / diameter For more information about additional mounting accessories please refer to page 186 0.032 Flange connection 12 x 12M at a graduated diameter of 208 mm 0°– 360° continuously adjustable (for further details see application note) 1395 x 315 x 330 mm 1241 / 230 and 280 mm 81 0° Tri-Sector Pipe Antenna 1710 –2170 Frequency Range X Dual Polarization 65° Half-power Beam Width Adjust. Electr. Downtilt 0°– 10° 120° 240° 1710 –2170 1710 –2170 X X 65° 65° 0°– 10° 0°– 10° set by hand or by optional RCUs (Remote Control Units) XPol Tri-Sector Pipe 1710–2170 65° 18dBi 0°–10°T 1710 – 1880 MHz 1710–2170 1850 – 1990 MHz +45°, –45° +45°, –45° +45°, –45° 17.2 ... 17.5 ... 17.2 0° ... 5° ... 10° 17.6 ... 17.8 ... 17.6 0° ... 5° ... 10° 17.8 ... 17.9 ... 17.4 0° ... 5° ... 10° Horizontal: 63° Vertical: 6.7° Horizontal: 60° Vertical: 6.4° 0°– 10° 0°– 10° 0°– 10° 0° ... 5° ... 10° T 17 ... 15 ... 15 dB 0° ... 5° ... 10° T 17 ... 17 ... 15 dB 0° ... 5° ... 10° T 17 ... 17 ... 15 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB Typically: > 10 dB Typically: 20 dB Typically: > 10 dB Typically: 20 dB Typically: > 10 dB > 30 dB > 45 dB > 30 dB > 42 dB > 30 dB > 42 dB Polarization Average gain (dBi) Tilt Half-power beam width Copolar +45°/ –45° Horizontal: Vertical: Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection Sector 0° ±60° Isolation: Intrasystem Isolation: Intersystem 66° 7° 1920 – 2170 MHz Impedance 50 Ω 50 Ω 50 Ω VSWR < 1.5 < 1.5 < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) compact service area Frequency range 1800/1900/2000/2600 XPol Electrical datas per sector 80010360 Type No. 0° 7-16 –45° 7-16 Mechanical specifications +45° Input 1710 –2170 Connector position 7-16 +45° 1710 –2170 –45° 240° 7-16 –45° Adjustment mechanism 7-16 1710 –2170 +45° 120° 7-16 Weight Wind load Bottom – inside service area 3 x 1, Position bottom continuously adjustable inside service area 56 kg 320 N (at 150 km/h) Max. wind velocity 200 km/h Natural frequency 19 – 21 Hz Damping ratio Mechanical interface Packing size Height / diameter 82 3 x 2 x 7-16 female 0.032 Flange connection 12 x 12M at a graduated diameter of 208 mm 0°– 360° continuously adjustable (for further details see application note) 2030 x 400 x 400 mm 1823 / 230 and 280 mm For more information about additional mounting accessories please refer to page 186 Additional Options for Tri-Sector-Antennas Accessories delivered with the Tri-Sector-Pipe Antenna: 1. 2. 3. 4. Clamping ring for mounting the antenna on the customer-supplied base Lightning conductor rod Ring bolt as attachment possibility for lifting aid Wrench (SW41 + SW27) for attaching the RCU Optional Accessories: The following components may be ordered separately 1. 86010025 2. 78210352 3. 78210353 4. 78210354 5. 78210355 6. 85010010 7. 738440 8. 737306 9. 85010111 10. 782 10xxx Slimline Remote Control Unit (RCU) Multipack TMA MPTMA-UMTS-12-AISG-6P with 12 dB (equals 3*DTMA) and RET-Support Multipack TMA MPTMA-UMTS-24-AISG-6P with 24 dB (equals 3*DTMA) and RET-Support Multipack TMA MPTMA-UMTS-12-CW-6P with 12 dB (equals 3*DTMA) without RET-Support Multipack TMA MPTMA-UMTS-24-CW-6P with 24 dB (equals 3*DTMA) without RET-Support Flexible Sealing Frame (Roxtec frame to seal connection between the mast and the antenna, see below Azimuth Adjustment Tool, see page 201 3-way power splitter for optional omni pattern Inlay mounting plate kit for 3-way splitter and DTMA for omni pattern Double TMA optional for omni pattern (several types, see page 302) View inside service zone with MPTMA and Slimline RCUs Flexible Sealing Frame Type No. Outer diameter 85010010 180 mm Cable diameter (6x) 15 – 42 mm Cable diameter (3x) 3.5 – 10.5 mm Frame-Material Stainless steel Sealing-Material Halogen free cross linkable compound on ethylene-propylene rubber (EPDM) Material of screws Accessories Required assembly tools Weight (without packaging) Packing size (L x W x H) Stainless steel Mounting lubricant Socket wrench size 6 mm 1.8 kg approx. 208 x 208 x 68 mm For further information please refer to separate application note under: www.kathrein.de/en/mca/index-customerportal.htm 83 84 Summary – Directional Antennas 2-Multi-band 1800/1900/2000/2600 Dual Polarization + 45°/ –45° Type No. Height [mm] Connector position Page XXPol Panel 1710–2170 1710–2170 65° 65° 15dBi 15dBi 0°–10°T 0°–10°T 742233V01 679 bottom 86 XXPol Panel 1710–2690 1710–2690 65° 65° 16.5dBi 16.5dBi 0°–12°T 0°–12°T 80010682 855 bottom 87 XXPol Panel 1710–2170 1710–2170 65° 65° 18dBi 18dBi 0°–8°T 0°–8°T 742237 1147 bottom 88 XXPol Panel 1710–2170 2490–2690 65° 60° 18dBi 18dBi 0°–10°T 0°–10°T 80010644 1410 bottom 88 XXPol Panel 1710–2200 1710–2200 65° 65° 18dBi 18dBi 0°–10°T 0°–10°T 742236V01 1319 bottom 89 XXPol Panel 1710–2690 1710–2690 65° 65° 18dBi 18dBi 0°–12°T 0°–10°T ESLS 80010622 1415 bottom 90 XXPol Panel 1710–2200 1710–2200 65° 65° 18dBi 18dBi 0°–15°T 0°–15°T ESLS 80010510V01 1389 bottom 91 XXPol Panel 1710–2170 1710–2170 65° 65° 19.5dBi 19.5dBi 0°–6°T 0°–6°T 742235V01 1959 bottom 92 XXPol Panel 1710–2200 1710–2200 65° 65° 19dBi 19dBi 0°–10°T 0°–10°T 80010511V01 1999 bottom 93 XXPol Panel 1710–2180 1710–2180 88° 88° 16.5dBi 16.5dBi 0°–10°T 0°–10°T 742352V01 1319 bottom 94 ESLS 1800/1900/2000/2600 XXPol 2-Multi Type New or changed product ying deplo nnas, n e h e W d Ant r using ti-ban 2-Mul so conside biners Com e al pleas ual-band 21) D and 2 al speci pages 220 (see Abbreviations: ESLS: Enhanced Side Lobe Suppression (above or below horizon) 85 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 1710 –2200 X X 65° 65° XXPol Panel 1710–2170/1710–2170 65°/65° 15/15dBi 0°–10°/0°–10°T s clamp d e d lu c in 742233V01 Type No. Frequency range 1710–2170 1850 – 1990 MHz 1710 – 1880 MHz Polarization 1920 – 2170 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain 4 x 15 dBi 4 x 15.2 dBi 4 x 15.3 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 67° 65° 62° Copolar: > 25 dB Total power: > 25 dB Copolar: > 25 dB Total power: > 25 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB Typically: 10 dB Typically: 20 dB Typically: 10 dB Typically: 20 dB Typically: 10 dB 13.7° 13° Vertical Pattern: Half-power beam width Electrical tilt 14° 0° – 10°, continuously adjustable 1800/1900/2000/2600 XXPol 2-Multi Sidelobe suppression for first 0° ... 4° ... 8° ... 10°T 0° ... 4° ... 8° ... 10°T sidelobe above main beam 16 ... 16 ... 15 .... 15 dB 16 ... 16 ... 16 ... 16 dB VSWR Isolation, between inputs 0° ... 4° ... 8° ... 10°T 16 ... 16 ... 16 ... 16 dB < 1.5 > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 250 W (at 50 °C ambient temperature) Input Connector position 4 x 7-16 female Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 350 / 85 / 370 N Height/width/depth Category of mounting hardware Weight Scope of supply 86 679 / 323 / 71 mm L (Light) 10.5 kg / 12.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2690 1710 –2690 X X 65° 65° XXPol Panel 1710–2690/1710–2690 65°/65° 16.5/16.5dBi 0°–12°/0°–12°T s clamp d e d lu c in 80010682 Type No. Frequency range 1710–2690 1920 – 2200 MHz 2200 – 2490 MHz 1710 – 1990 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain at 0° tilt 4 x 15.8 dBi 4 x 16.2 dBi 4 x 16.6 dBi 4 x 16.7 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Sector 0° ±60° 65° 64° 60° 61° > 30 dB > 30 dB > 30 dB > 28 dB Typically: 25 dB > 8 dB Typically: 25 dB > 8 dB Typically: 25 dB > 8 dB Typically: 25 dB > 10 dB 10° 9° 8.7° Vertical Pattern: 11° Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports 0°– 12°, continuously adjustable 0° ... 6° ... 12° T ≥ 12 ... 13 ... 15 dB 0° ... 6° ... 12° T ≥ 13 ... 14 ... 16 dB 0° ... 6° ... 12° T ≥ 13 ... 15 ... 16 dB < 1.5 > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 250 W (at 50 °C ambient temperature) Input Connector position 4 x 7-16 female Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 440 / 100 / 460 N Height/width/depth Category of mounting hardware Weight Scope of supply 0° ... 6° ... 12° T ≥ 15 ... 15 ... 17 dB 1800/1900/2000/2600 XXPol 2-Multi Half-power beam width 855 / 323 / 71 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 87 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 1710 –2170 X X 65° 65° XXPol Panel 1710–2170/1710–2170 65°/65° 18/18dBi 0°–8°/0°–8°T s clamp d e includ 742237 Type No. Frequency range 1710–2170 1850 – 1990 MHz 1710 – 1880 MHz Polarization 1920 – 2170 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain 4 x 17.5 dBi 4 x 17.7 dBi 4 x 18 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 65° 63° 61° Copolar: 30 dB Copolar: 30 dB Copolar: 30 dB Avg.: 25 dB > 10 dB Avg.: 25 dB > 10 dB Avg.: 25 dB > 10 dB 8° 7.5° Vertical Pattern: Half-power beam width 8.3° Electrical tilt Sidelobe suppression for first sidelobe above main beam, Avg. 0° – 8°, continuously adjustable 0° ... 4° ... 8° T 20 ... 20 .... 18 dB 0° ... 4° ... 8° T 20 ... 20 ... 18 dB VSWR < 1.5 1800/1900/2000/2600 XXPol 2-Multi Isolation, between inputs Intermodulation IM3 Max. power per input 0° ... 4° ... 8° T 20 ... 20 ... 18 dB > 30 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 590 / 135 / 610 N Height/width/depth 1147 / 323 / 71 mm Category of mounting hardware Weight Scope of supply M (Medium) 12.5 kg / 14.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XXPol Panel 1710–2170/2490–2690 65°/60° 18/18dBi 0°–10°/0°–10°T 80010644 Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 88 1710–2170 1710 – 1990 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 17.5 dBi 2 x 17.7 dBi 68° > 25 dB Typically: 25 dB > 8 dB 6.7° 65° > 25 dB Typically: 25 dB > 8 dB 6.3° 0°– 10° 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 17 ... 17 ... 16 dB ≥ 17 ... 17 ... 16 dB s clamp d e includ 2490–2690 2490 – 2690 MHz +45°, –45° 2 x 18.0 dBi 61° > 25 dB Typically: 25 dB > 10 dB 5.4° 0°– 10° 0° ... 6° ... 10° T ≥ 17 ... 17 ... 16 dB < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB < –150 dBc < –150 dBc (2 x 43 dBm carrier) (2 x 43 dBm carrier) 200 W* 200 W* 400 W* 400 W* 4 x 7-16 female Bottom 2 x, Position bottom continuously adjustable Frontal / lateral / rearside: 370 / 145 / 400 N 1410 / 155 / 89 mm M (Medium) 10 kg / 12 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter * (at 50 °C ambient temperature) For more information about additional mounting accessories please refer to page 186 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 1710 –2170 X X 65° 65° XXPol Panel 1710–2200/1710–2200 65°/65° 18/18dBi 0°–10°/0°–10°T s clamp d e includ 742236V01 Type No. Frequency range 1710 – 1880 MHz Polarization 1710–2200 1850 – 1990 MHz 1920 – 2200 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain 4 x 17.6 dBi 4 x 17.8 dBi 4 x 18 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 64° 64° 62° Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 6.8° 6.5° Vertical Pattern: Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between inputs Intermodulation IM3 Max. power per input Input Connector position 7° 0° – 10°, continuously adjustable 0° ... 5° ... 10° T 20 ... 18 .... 16 dB 0° ... 5° ... 10° T 20 ... 18 ... 16 dB 0° ... 5° ... 10° T 16 ... 18 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 660 / 155 / 690 N Height/width/depth Category of mounting hardware Weight Scope of supply 1800/1900/2000/2600 XXPol 2-Multi Half-power beam width 1319 / 323 / 71 mm M (Medium) 15 kg / 17 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 186 89 Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2690 1710 –2690 X X 65° 65° XXPol Panel 1710–2690/1710–2690 65°/65° 18/18dBi 0°–12°/0°–12°T ESLS s clamp d e d lu c in 80010622 Type No. Frequency range 1710–2690 1920 – 2200 MHz 2200 – 2490 MHz 1710 – 1990 MHz Polarization Gain (dBi) Tilt 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 17.4 ... 17.4 ... 17.3 0° ... 6° ... 12° 17.8 ... 17.6 ... 17.5 0° ... 6° ... 12° 18.0 ... 17.9 ... 17.5 0° ... 6° ... 12° 18.0 ... 17.7 ... 17.3 0° ... 6° ... 12° Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±30°) Cross polar ratio Sector 65° 65° 61° 61° > 25 dB, avg. 28 dB > 26 dB, avg. 28 dB > 25 dB, avg. 27 dB > 25 dB, avg. 27 dB Typically: 30 dB > 10 dB Typically: 30 dB > 10 dB Typically: 25 dB > 8 dB Typically: 25 dB > 10 dB 6.5° 5.9° 5.7° 0° ±60° Vertical Pattern: Half-power beam width 7.1° Electrical tilt 0°– 12°, continuously adjustable 1800/1900/2000/2600 XXPol 2-Multi Sidelobe suppression for first sidelobe above main beam 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB VSWR 0° ... 6° ... 12° T ≥ 18 ... 17 ... 17 dB < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 720 / 165 / 740 N Height/width/depth 1415 / 323 / 71 mm Category of mounting hardware M (Medium) Weight 17.5 kg / 19.5 kg (clamps incl.) Scope of supply 90 0° ... 6° ... 12° T ≥ 18 ... 18 ... 17 dB Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2690 +45° 1710–2690 –45° 1710–2690 +45° 1710–2690 –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 1710 –2200 X X 65° 65° XXPol Panel 1710–2200/1710–2200 65°/65° 18/18dBi 0°–15°/0°–15°T ESLS 80010510V01 Type No. Frequency range 1710 – 1880 MHz Polarization 1710–2200 1850 – 1990 MHz 1920 – 2170 MHz s clamp d e d lu c in 2000 – 2200 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain at 0° tilt 4 x 17.5 dBi 4 x 17.6 dBi 4 x 17.7 dBi 4 x 17.8 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±30°) Cross polar ratio Sector 0° ±60° 65° 63° 62° 62° ≥ 30 dB ≥ 30 dB ≥ 30 dB ≥ 28 dB 24 dB ≥ 9 dB 24 dB ≥ 9 dB 24 dB ≥ 10 dB 26 dB ≥ 10 dB 7.5° 7.2° 6.9° Vertical Pattern: Half-power beam width 7.9° Electrical tilt 0°– 15°, continuously adjustable Sidelobe suppression 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T – for first sidelobe above main beam ≥ 17 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 18 dB ≥ 15 ... 19 ... 18 ... 17 dB ≥ 14 ... 18 ... 18 ... 16 dB – within 0°–20° sector above horizon ≥ 17 ... 18 ... 18 ... 16 dB ≥ 16 ... 17 ... 17 ... 16 dB ≥ 15 ... 17 ... 17 ... 16 dB ≥ 14 ... 16 ... 16 ... 15 dB 23 dB 22 dB 21 dB VSWR 20 dB 1800/1900/2000/2600 XXPol 2-Multi Null-fill at 0° tilt < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –153 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottomcontinuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 700 / 160 / 720 N Height/width/depth 1389 / 323 / 71 mm Category of mounting hardware M (Medium) Weight 17 kg / 19 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2200 +45° 1710–2200 –45° 1710–2200 +45° 1710–2200 –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 91 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2170 1710 –2170 X X 65° 65° XXPol Panel 1710–2170/1710–2170 65°/65° 19.5/19.5dBi 0°–6°/0°–6°T s clamp d e d lu c in 742235V01 Type No. Frequency range 1710–2170 1850 – 1990 MHz 1710 – 1880 MHz Polarization 1920 – 2170 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain 4 x 19 dBi 4 x 19.2 dBi 4 x 19.5 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 65° 64° 63° Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 24 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 4.6° 1800/1900/2000/2600 XXPol 2-Multi Electrical tilt 4.4° 4.2° 0° – 6°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T sidelobe above main beam 17 ... 17 ... 14 .... 14 dB 17 ... 17 ... 15 ... 15 dB VSWR 0° ... 2° ... 4° ... 6° T 17 ... 17 ... 15 ... 15 dB < 1.5 Isolation, between inputs > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1010 / 220 / 1040 N Height/width/depth 1959 / 323 / 71 mm Category of mounting hardware M (Medium) Weight Scope of supply 92 18 kg / 20 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2170 +45° 1710–2170 –45° 1710–2170 +45° 1710–2170 –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2200 1710 –2200 X X 65° 65° XXPol Panel 1710–2200/1710–2200 65°/65° 19/19dBi 0°–10°/0°–10°T ESLS s clamp d e d lu c in 80010511V01 Type No. Frequency range 1710–2200 1850 – 1990 MHz 1920 – 2170 MHz 1710 – 1880 MHz 2000 – 2200 MHz Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain Tilt 18.5 ... 18.7 ... 18.5 dBi 18.7 ... 19.0 ... 18.5 dBi 18.7 ... 19.0 ... 18.4 dBi 18.7 ... 18.9 ... 18.3 dBi 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T Horizontal Pattern: Half-power beam width 66° 65° 65° 63° ≥ 30 dB ≥ 30 dB ≥ 30 dB ≥ 28 dB Typically: 22 dB ≥ 10 dB Typically: 22 dB ≥ 10 dB Typically: 22 dB ≥ 10 dB Typically: 22 dB ≥ 10 dB 4.8° 4.6° 4.4° Front-to-back ratio (180° ±30°) Cross polar ratio Sector 0° ±60° Vertical Pattern: Half-power beam width 5.0° 0°– 10°, continuously adjustable Sidelobe suppression – for first sidelobe above main beam – within 0°–20° sector above horizon 0° ... 4° ... 8° ... 10° T ≥ 20 ... 20 ... 18 ... 18 dB ≥ 18 ... 18 ... 17 ... 17 dB 0° ... 4° ... 8° ... 10° T ≥ 20 ... 20 ... 18 ... 18 dB ≥ 17 ... 18 ... 17 ... 15 dB VSWR 0° ... 4° ... 8° ... 10° T ≥ 19 ... 20 ... 18 ... 18 dB ≥ 17 ... 17 ... 17 ... 15 dB 0° ... 4° ... 8° ... 10° T ≥ 18 ... 20 ... 18 ... 18 dB ≥ 17 ... 17 ... 14 ... 12 dB 1800/1900/2000/2600 XXPol 2-Multi Electrical tilt < 1.5 Isolation, between ports > 30 dB Intermodulation IM3 < –153 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1020 / 230 / 1080 N Height/width/depth 1999 / 323 / 71 mm Category of mounting hardware M (Medium) Weight 18 kg / 20 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2200 +45° 1710–2200 –45° 1710–2200 +45° 1710–2200 –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 93 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 –2180 1710 –2180 X X 88° 88° XXPol Panel 1710–2180/1710–2180 88°/88° 16.5/16.5dBi 0°–10°/0°–10°T s clamp d e d lu c in 742352V01 Type No. Frequency range 1710–2180 1850 – 1990 MHz 1710 – 1880 MHz 1920 – 2180 MHz Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain (average) Tilt 16.1 ... 16.3 ... 16.0 dBi 16.2 ... 16.4 ... 16.1 dBi 16.5 ... 16.7 ... 16.2 dBi 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector 0° ±60° 88° 90° 88° Copolar: > 24 dB Total power: > 24 dB Copolar: > 24 dB Total power: > 24 dB Copolar: > 24 dB Total power: > 24 dB Typically: 15 dB > 8 dB Typically: 15 dB > 7.5 dB Typically: 15 dB > 7 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 7.4° 1800/1900/2000/2600 XXPol 2-Multi Electrical tilt 7° 6.5° 0° – 10°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T sidelobe above main beam 18 ... 17 ... 16 ... 15 dB 18 ... 17 ... 16 ... 15 dB 17 ... 17 ... 16 ... 15 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 30 dB Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 300 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 660 / 155 / 690 N Height/width/depth 1319 / 323 / 71 mm Category of mounting hardware M (Medium) Weight Scope of supply 94 16.5 kg / 18.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 +45° 1710–2180 –45° 1710–2180 +45° 1710–2180 –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Summary – Directional Antennas Dual-band 800/900 – 1800/2000/2600 Type XXPol Panel 806–960 1710–2180 XXPol Panel 790–960 1710–2170 790–960 1710–2170 XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel 790–960 1710–2180 790–960 1710–2180 870–960 1710–1880 870–960 1710–1880 790–960 1710–2180 790–960 1710–2180 790–960 1710–2180 790–960 1710–2690 870–960 1710–1880 790–960 1710–2180 790–960 1710–2180 790–960 1710–2180 C C C C C C C Type No. Height [mm] Connector position Page 65° 60° 8.5dBi 9.5dBi 0°T 0°T 80010454V01 270 bottom or top 96 65° 60° 65° 60° 12dBi 14dBi 12dBi 14dBi 0°T 0°T 0°T 0°T 742226V01 579 bottom or top 97 742222V01 579 bottom or top 98 65° 65° 65° 65° 14.5dBi 17.5dBi 14.5dBi 17.5dBi 0°–14°T 0°–8°T 0°–14°T 0°–8°T 742264V02 1334 bottom 99 742223V02 1334 bottom 100 65° 60° 65° 60° 65° 65° 65° 65° 65° 65° 65° 65° 17dBi 18.5dBi 17dBi 18dBi 16dBi 18.5dBi 16.5dBi 18.5dBi 16dBi 18.5dBi 16.5dBi 19dBi 0°T 0°T 0°T 0°T 0°–10°T 0°–6°T 2°–14°T 4°–14°T 0°–10°T 0°–6°T 0°–10°T 0°–6°T 741327 1936 bottom or top 101 741322 1936 bottom or top 101 742265V02 1933 bottom 102 80010485V01 2038 bottom 103 742224V02 1933 bottom 104 80010665 1997 bottom 105 65° 60° 65° 65° 65° 65° 65° 65° 17dBi 18dBi 17dBi 18.5dBi 17.5dBi 18.5dBi 17dBi 18.5dBi 2°–8°T 2°T 0°–7°T 0°–6°T 4°–12°T 4°–14°T 0°–7°T 0°–6°T 742047V01 2580 bottom 106 742266V02 2533 bottom 107 80010486V01 2516 bottom 108 742225V02 2533 bottom 109 XXPol Panel 790–960 1710–2180 88° 88° 13.5dBi 16.5dBi 0°–12°T 0°–10°T 80010121V01 1384 bottom 110 XXPol Panel 790–960 1710–2180 88° 88° 15.2dBi 18dBi 0°–10°T 0°–6°T 80010122V01 1917 bottom 111 XXPol Panel 790–960 1710–2180 88° 88° 16.5dBi 18dBi 0°–7°T 0°–6°T 80010123V03 2635 bottom 112 C = integrated Combiner New or changed product ying deplo nas, When g Anten band sider usin s l a u D r n e o n c i Comb ) e also 1 pleas ual-band 2 2 and al D speci pages 220 e e (s 95 800/900 – 1800/2000/2600 XXPol Dual Polarization + 45°/ –45° Dual-band Panel Dual Polarization Half-power Beam Width 806 – 960 1710 –2180 X X 65° 65° XXPol Panel 806–960/1710–2180 C 65°/ 65° 8.5/9.5dBi s clamp d e d lu c in 80010454V01 Type No. Frequency range 806 – 866 MHz 806 –960 824 – 894 MHz 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain 2 x 8.5 dBi 2 x 8.5 dBi 2 x 8.5 dBi 2 x 9.5 dBi 2 x 9.5 dBi 2 x 9.2 dBi 67° 67° 65° 60° 63° 68° Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection Sector [dB] Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 [dB] Total power: > 20 Total power: > 20 Total power: > 22 Total power: > 22 Total power: > 22 Total power: > 22 0° ±60° Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Typically: 19 dB > 10 dB Typically: 20 dB > 10 dB 68° 68° 69° 64° 62° 60° Vertical Pattern: Half-power beam width VSWR < 1.5 Isolation: Intrasystem > 30 dB Intermodulation IM3 Max. power < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 800/900 – 1800/2000/2600 XXPol Max. power per combined input 100 W (at 50 °C ambient temperature) 350 W (at 50 °C ambient temperature) nput 2 x 7-16 female Connector position Bottom or top* Wind load (at 150 km/h) Frontal / lateral / rearside: 95 / 35 / 130 N Height/width/depth 270 / 262 / 116 mm Category of mounting hardware M (Medium) Weight 4.5 kg / 6.5 kg (clamps incl.) Scope of supply Panel and 1 unit of tension bands for 45 – 125 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. 806–960 –45° 1710–2180 –45° 96 806–960 +45° 1710–2180 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2170 X X 65° 60° XXPol Panel 790–960/1710–2170 65°/ 60° 12/14dBi 0°/0°T s clamp d e d lu c in 742226V01 Type No. Frequency range 790 – 862 MHz 790–960 824 – 894 MHz 1710–2170 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain 2 x 11.1 dBi 2 x 11.4 dBi 2 x 11.8 dBi 2 x 12.8 dBi 2 x 13.3 dBi 2 x 13.6 dBi 68° 67° 65° 66° 60° 60° Horizontal Pattern: Half-power beam width Front-to-back ratio (180° ±30°) Cross polar ratio Maindirection Sector [dB] Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 [dB] Total power: > 20 Total power: > 20 Total power: > 22 Total power: > 22 Total power: > 22 Total power: > 22 0° ±60° Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 16 dB > 10 dB Typically: 18 dB > 10 dB Tracking, Avg. 1.0 dB 0.5 dB Squint ±3.0° ±1.5° Typically: 20 dB > 10 dB Vertical Pattern: 34° 33° Electrical tilt 30° 20° 18° 0°, fixed VSWR Isolation: Intrasystem < 1.5 < 1.5 > 30 dB > 30 dB Isolation: Intersystem 17.5° 0°, fixed > 45 dB (790 – 960 // 1710 – 2170 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) Max. power per input 250 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position 800/900 – 1800/2000/2600 XXPol Half-power beam width Bottom or top Wind load (at 150 km/h) Frontal / lateral / rearside: 200 / 90 / 250 N Height/width/depth 579 / 262 / 139 mm Category of mounting hardware M (Medium) Weight 7.5 kg / 9.5 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2170 –45° 790–960 –45° 790–960 +45° 1710–2170 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 97 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2170 X X 65° 60° XXPol Panel 790–960/1710–2170 C 65°/ 60° 12/14dBi 0°/0°T Frequency range 790 – 862 MHz 790–960 824 – 894 MHz 1710–2170 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain 2 x 11.1 dBi 2 x 11.4 dBi 2 x 11.8 dBi 2 x 12.5 dBi 2 x 13.3 dBi 2 x 13.6 dBi Horizontal: 68° Vertical: 34° Horizontal: 67° Vertical: 33° Horizontal: 65° Vertical: 30° Horizontal: 66° Vertical: 20° Horizontal: 60° Vertical: 18° Horizontal: 60° Vertical: 17.5° Half-power beam width Copolar +45°/ –45° Front-to-back ratio (180° ± 30°) Cross polar ratio Maindirection Sector [dB] Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 [dB] Total power: > 20 Total power: > 20 Total power: > 22 Total power: > 22 Total power: > 22 Total power: > 22 0° ±60° Isolation: Intrasystem VSWR Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 18 dB > 10 dB Typically: 18 dB > 10 dB Typically: 20 dB > 10 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 Intermodulation IM3 (2 x 43 dBm carrier) Max. power < –150 dBc < –150 dBc 250 W (at 50 °C ambient temperature) Max. power per combined input Input Bottom or top Wind load (at 150 km/h) Frontal / lateral / rearside: 200 / 90 / 250 N Height/width/depth 579 / 262 / 139 mm Category of mounting hardware M (Medium) Weight 7.5 kg / 9.5 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. 790 – 960 –45° 1710 – 2170 –45° 98 200 W (at 50 °C ambient temperature) 450 W (at 50 °C ambient temperature) 2 x 7-16 female Connector position 800/900 – 1800/2000/2600 XXPol s clamp d e d lu c in 742222V01 Type No. 790 – 960 +45° 1710 – 2170 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 824 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/ 65° 14.5/17.5dBi 0°–14°/0°–8°T s clamp d e d lu c in 742264V02 Type No. Frequency range Polarization Gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 894 MHz 880 – 960 MHz +45°, –45° +45°, –45° +45°, –45° 1710–2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 14.1 ... 14.1 ... 13.7 14.3 ... 14.2 ... 13.8 14.5 ... 14.4 ... 13.9 17.1 ... 17.3 ... 17.1 17.2 ... 17.4 ... 17.1 17.3 ... 17.5 ... 17.2 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 62° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 32 dB > 32 dB > 32 dB Cross polar ratio Maindirection Sector Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0° ±60° Tracking, Avg. 1 dB 0.5 dB Squint ±2° ±3° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. 16.5° 16° 15.3° 7.4° 7.1° 6.7° 0°– 14° 0°– 14° 0°– 14° 0°– 8° 0°– 8° 0°– 8° Sidelobe suppression for first 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T sidelobe above main beam avg. 17 ... 16 ... 15 dB 19 ... 18 ... 18 dB 17 ... 18 ... 17 dB 17 ... 17 ... 16 dB 15 ... 15 ... 15 dB 16 ... 16 ... 15 dB Isolation: Intrasystem < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Isolation: Intersystem > 45 dB, Typ. > 50 dB (790 – 960 // 1710 – 2180 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) Max. power per input Total power 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) Input 800/900 – 1800/2000/2600 XXPol VSWR 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 560 / 260 7 600 N Height/width/depth 1334 / 261 / 146 mm Category of mounting hardware M (Medium) Weight 15.5 kg / 17.5 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 99 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/ 65° 14.5/17.5dBi 0°–14°/0°–8°T Frequency range s clamp d e d lu c in 742223V02 Type No. 790–960 1710–2180 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 14.1 ... 14.1 ... 13.7 14.5 ... 14.4 ... 13.9 17.1 ... 17.3 ... 17.1 17.2 ... 17.4 ... 17.1 17.3 ... 17.5 ... 17.2 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° 800/900 – 1800/2000/2600 XXPol Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 65° 65° 62° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 32 dB > 32 dB > 32 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection 0° 25 dB 25 dB 25 dB 25 dB 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.0° ±3.0° Vertical Pattern: Half-power beam width 16.5° 15.3° 7.4° 7.1° 6.7° Electrical tilt 0°– 14° 0°– 14° 0°– 8° 0°– 8° 0°– 8° continuously adjustable Sidelobe suppression for first 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T sidelobe above main beam avg. 17 ... 16 ... 15 dB 17 ... 18 ... 17 dB 17 ... 17 ... 16 dB 15 ... 15 ... 15 dB 16 ... 16 ... 15 dB VSWR Isolation: Intrasystem Intermodulation IM3 Max. power per input Total power per combined input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply Integrated combiner < 1.5 > 30 dB < –150 dBc 250 W* 200 W* 450 W* 2 x 7-16 female (long neck) Bottom 2 x, Position bottom continuously adjustable Frontal / lateral / rearside: 560 / 260 / 600 N 1334 / 261 / 146 mm M (Medium) 15.5 kg / 17.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter The insertion loss is included in the given antenna gain values. * (at 50 °C ambient temperature) 790–960 –45° 1710–2180 –45° 100 790–960 +45° 1710–2180 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 870 – 960 1710 –1880 X X 65° 60° XXPol Panel 870–960/1710–1880 65°/ 60° 17/18.5dBi 741327 Type No. Polarization Gain Half-power beam width Copolar +45°/ –45° 870900 –960 870 – 960 MHz 1800 1710–1880 1710 – 1880 MHz +45°, –45° +45°, –45° 2 x 17 dBi 2 x 18.5 dBi Horizontal: 65° Vertical: 9.5° Horizontal: 60° Vertical: 5.5° Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input > 15 dB > 30 dB > 30 dB > 30 dB (GSM 900 – GSM 900)1 > 30 dB (GSM 1800 – GSM 1800) > 30 dB (GSM 900 – GSM 1800) < 1.5 < 1.5 < –150 dBc < –150 dBc 400 W 200 W (at 50 °C ambient temperature) Input 4 x 7-16 female Connector position Bottom or top Weight Wind load (at 150 km/h) Height/width/depth 19 kg Frontal / lateral / rearside: 330 / 200 / 770 N 1710–1880 –45° 870–960 –45° 870–960 +45° 1710–1880 +45° 7-16 7-16 7-16 7-16 1710–1880 –45° 870–960 –45° 870–960 +45° 1710–1880 +45° 1936 / 262 / 116 mm 800/900 – 1800/2000/2600 XXPol Frequency range XXPol Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi 741322 Type No. Frequency range Polarization Gain 870900 –960 870 – 960 MHz 1800 1710–1880 1710 – 1880 MHz +45°, –45° +45°, –45° 2 x 17 dBi 2 x 18 dBi Horizontal: 65° Vertical: 9.5° Horizontal: 60° Vertical: 5.5° Sidelobe suppression for first sidelobe above horizon > 15 dB > 15 dB Front-to-back ratio, copolar > 30 dB > 30 dB Isolation, between ports > 30 dB > 30 dB < 1.5 < 1.5 < –150 dBc < –150 dBc Half-power beam width Copolar +45°/ –45° VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Height/width/depth Integrated combiner 250 W 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top 19 kg Frontal / lateral / rearside: 330 / 200 / 770 N 1936 / 262 / 116 mm The insertion loss is included in the given antenna gain values. For more information about additional mounting accessories please refer to page 186 C C 7-16 7-16 101 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/ 65° 16/18.5dBi 0°–10°/0°–6°T s clamp d e d lu c in 742265V02 Type No. Frequency range Polarization Gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 894 MHz 880 – 960 MHz +45°, –45° +45°, –45° +45°, –45° 1710–2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 15.6 ... 15.5 ... 15.3 15.9 ... 15.8 ... 15.5 16.1 ... 16.0 ... 15.6 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ...18.7 ... 18.3 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° 68° 67° 65° 65° 65° 61° > 27 dB > 28 dB > 28 dB > 30 dB > 30 dB > 30 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Tracking, Avg. Squint 1.5 dB 0.5 dB ±2.5° ±2.5° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. 10.9° 10.6° 10° 5.0° 4.8° 4.6° 0.5°–9.5° 0.5°–9.5° 0.5°–9.5° 0°– 6° 0°– 6° 0°– 6° Sidelobe suppression for first 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 15 ... 16 ... 17 dB ≥ 15 ... 17 ... 19 dB ≥ 15 ... 18 ... 19 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB 800/900 – 1800/2000/2600 XXPol Isolation: Intersystem > 45 dB, Typ. > 50 dB (790 – 960 // 1710 – 2180 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) Max. power per input Total power 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) Input 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 850 / 380 / 910 N Height/width/depth 1933 / 261 / 146 mm Category of mounting hardware M (Medium) Weight 20 kg / 22 kg (clamps incl.) Scope of supply 102 Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2180 –45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/ 65° 16.5/18.5dBi 2°–14°/4°–14°T s clamp d e d lu c in 80010485V01 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.2 ... 16 ... 15.7 16.3 ... 16.1 ... 15.8 16.4 ... 16.2 ... 15.8 18 ... 18.2 ... 17.7 18.4 ... 18.5 ... 17.8 18.7 ... 18.6 ... 18 2° ... 8° ... 14° 2° ... 8° ... 14° 2° ... 8° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° Horizontal Pattern: Half-power beam width 68° 67° 65° 66° 64° 60° Front-to-back ratio (180°± 30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection Sector Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB Typically: 21 dB > 10 dB 10° 9.7° 9.3° 5° 4.7° 4.5° 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt 2°– 14°, continuously adjustable 4°– 14°, continuously adjustable Sidelobe suppression for first 2° ... 8° ... 14° T 2° ... 8° ... 14° T 2° ... 8° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T sidelobe above main beam 17 ... 17 ... 15 dB 17 ... 17 ... 16 dB 17 ... 17 ... 16 dB 20 ... 18 ... 15 dB 19 ... 18 ... 15 dB 18 ... 17 ... 15 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 35 dB (790 – 960 // 1710 – 2180 MHz) Intermodulation IM3 < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 800 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Connector position 800/900 – 1800/2000/2600 XXPol Max. power per input Total power Bottom Adjustment mechanism 1 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 750 / 380 / 900 N Height/width/depth 2038 / 262 / 139 mm Category of mounting hardware M (Medium) Weight 24 kg / 26 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 103 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/ 65° 16/18.5dBi 0°–10°/0°–6°T s clamp d e d lu c in 742224V02 Type No. Frequency range 790–960 790 – 862 MHz 880 – 960 MHz Polarization +45°, –45° Gain (dBi) Tilt 1710–2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 15.6 ... 15.5 ... 15.3 16.1 ... 16.0 ... 15.6 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ...18.7 ... 18.3 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 27 dB > 28 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Maindirection Sector Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0° ±60° Tracking, Avg. 1.5 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 10.9° 10° 5.0° 4.8° 4.6° Electrical tilt continuously adjustable 0.5°–9.5° 0.5°–9.5° 0°– 6° 0°– 6° 0°– 6° Sidelobe suppression for first 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 15 ... 16 ... 17 dB ≥ 15 ... 18 ... 19 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Max. power per input < –150 dBc 250 W* 200 W* Total power per combined input 450 W* Input 2 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 850 / 380 / 910 N Height/width/depth 1933 / 261 / 146 mm Category of mounting hardware M (Medium) Weight Scope of supply Integrated combiner 20 kg / 22 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter The insertion loss is included in the given antenna gain values. 790–960 –45° 1710–2180 –45° 104 790–960 +45° * (at 50 °C ambient temperature) 800/900 – 1800/2000/2600 XXPol Intermodulation IM3 1710–2180 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2690 X X 65° 65° XXPol Panel 790–960/1710–2690 65°/ 65° 16.5/19dBi 0°–10°/0°–6°T s clamp d e d lu c in 80010665 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 866 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2690 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2200 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 15.6 ... 15.6 ... 15.5 15.9 ... 16.0 ... 15.8 16.3 ... 16.4 ... 16.2 18.3 ... 18.5 ... 18.4 18.5 ... 18.7 ... 18.4 18.9 ... 19.2 ... 18.7 18.6 ... 19.0 ... 18.8 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 65° 62° 60° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection Sector Typically: 28 dB > 10 dB Typically: 30 dB > 10 dB Typically: 32 dB > 10 dB Typically: 16 dB > 10 dB Typically: 20 dB > 10 dB Typically: 18 dB > 10 dB Typically: 22 dB > 10 dB 9.7° 9.5° 9.0° 4.6° 4.4° 4.2° 3.5° 0° ±60° Vertical Pattern: Electrical tilt Min. sidelobe suppression for first sidelobe above main beam 0°–10°, continuously adjustable 0°–6°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 18 ... 16 ... 14 dB 18 ... 16 ... 15 dB 18 ... 17 ... 16 dB 16 ... 16 ... 15 dB 16 ... 16 ... 16 dB 16 ... 16 ... 16 dB 16 ... 16 ... 16 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB > 30 dB Isolation: Intersystem > 40 dB (790–960 // 1710–2690 MHz) Intermodulation IM3 Max. power per input Total power < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female Connector position 800/900 – 1800/2000/2600 XXPol Half-power beam width Bottom Adjustment mechanism 2x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1020 / 410 / 1080 N Height/width/depth 1997 / 299 / 152 mm Weight 26 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 1710 – 2690 –45° 790 – 960 –45° 790 – 960 +45° 1710 – 2690 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 105 Dual-band Panel Dual Polarization Half-power Beam Width 870 – 960 1710 –1880 X X 65° 60° XXPol Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi 2°–8°T/2°T Type No. Frequency range Polarization Gain 870900 –960 870 – 960 MHz 1800 1710–1880 1710 – 1880 MHz +45°, –45° +45°, –45° 2 x 17 dBi (–0.5 dB) Tracking, Avg. 2 x 18 dBi (–0.5 dB) 1 dB Squint ±2.0° Half-power beam width Copolar +45°/ –45° Horizontal: Vertical: Electrical tilt 2°– 8°, adjustable 2°, fixed Sidelobe suppression for first sidelobe above horizon 2° ... 4° ... 6° ... 8° T 20 ... 18 ... 17 ... 15 dB 2° T 17 dB Front-to-back ratio, copolar > 30 dB > 30 dB Isolation, between ports > 30 dB > 30 dB < 1.5 < 1.5 < –150 dBc < –150 dBc VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position 800/900 – 1800/2000/2600 XXPol s clamp d e d lu c in 742047V01 Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware 65° 7° Horizontal: Vertical: 250 W 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 870–960 +45° 1710–1880 +45° C C 2580 / 262 / 116 mm 7-16 7-16 H (Heavy) 25 kg / 27 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 106 870–960 –45° 1710–1880 –45° Frontal / lateral / rearside: 930/ 400 / 1270 N Weight Integrated combiner 60° 6° The insertion loss is included in the given antenna gain values. For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/ 65° 17/18.5dBi 0°–7°/0°–6°T s clamp d e d lu c in 742266V02 Type No. Frequency range Polarization Gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 894 MHz 880 – 960 MHz +45°, –45° +45°, –45° +45°, –45° 1710–2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 16.6 ... 16.6 ... 16.5 17.0 ... 16.9 ... 16.7 17.0 ... 17.1 ... 16.9 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ...18.7 ... 18.3 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° 68° 67° 65° 65° 65° 61° > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Typically: 30 dB > 10 dB Typically: 30 dB > 10 dB Typically: 30 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Tracking, Avg. 1 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. 8.0° 7.7° 7.2° 5.0° 4.8° 4.6° 0°–7° 0°–7° 0°–7° 0°– 6° 0°– 6° 0°– 6° Sidelobe suppression for first 0° ... 3° ... 7° T 0° ... 3° ... 7° T 0° ... 3° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 17 ... 17 ... 15 dB ≥ 17 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB Isolation: Intrasystem < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Isolation: Intersystem > 45 dB, Typ. > 50 dB (790 – 960 // 1710 – 2180 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) Max. power per input Total power 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) Input 800/900 – 1800/2000/2600 XXPol VSWR 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1160 / 500 / 1210 N Height/width/depth 2533 / 261 / 146 mm Category of mounting hardware H (Heavy) Weight 24 kg / 26 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter 1710 – 2180 –45° 790 – 960 –45° 790 – 960 +45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 107 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/ 65° 17.5/18.5dBi 4°–12°/4°–14°T s clamp d e d lu c in 80010486V01 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.8 ... 16.7 ... 16.6 17 ... 16.8 ... 16.8 17.2 ... 17.0 ... 16.8 17.8 ... 18.1 ... 17.5 18.3 ... 18.3 ... 17.8 18.7 ... 18.7 ... 18.0 4° ... 8° ... 12° 4° ... 8° ... 12° 4° ... 8° ... 12° 4° ... 9° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° Horizontal Pattern: Half-power beam width 68° 67° 66° 66° 64° 61° Front-to-back ratio (180°± 30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection Sector Typically: 23 dB > 10 dB Typically: 24 dB > 10 dB Typically: 25 dB > 10 dB Typically: 18 dB > 10 dB Typically: 18 dB > 10 dB Typically: 20 dB > 10 dB 7.5° 7.4° 7.2° 5° 4.8° 4.6° 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt 4°– 12°, continuously adjustable 4°– 14°, continuously adjustable Sidelobe suppression 4° ... 8° ... 12° T 4° ... 8° ... 12° T 4° ... 8° ... 12° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T – for first sidelobe above main beam 18 ... 17 ... 16 dB 19 ... 18 ... 18 dB 19 ... 18 ... 18 dB 20 ... 18 ... 16 dB 19 ... 19 ... 16 dB 18 ... 18 ... 18 dB – within 0°–20° sector above horizon 15 ... 15 ... 14 dB 16 ... 15 ... 14 dB 16 ... 15 ... 14 dB 17 ... 17 ... 15 dB 17 ... 17 ... 15 dB 17 ... 17 ... 15 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 45 dB (790 – 960 // 1710 – 2180 MHz) Intermodulation IM3 800/900 – 1800/2000/2600 XXPol Max. power per input Total power < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 800 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 920 / 460 / 1150 N Height/width/depth 2516 / 262 / 139 mm Category of mounting hardware H (Heavy) Weight 28 kg / 30 kg (clamps incl.) Scope of supply 108 Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/ 65° 17/18.5dBi 0°–7°/0°–6°T s clamp d e d lu c in 742225V02 Type No. Frequency range 790–960 790 – 862 MHz 880 – 960 MHz Polarization +45°, –45° Gain (dBi) Tilt 1710–2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.6 ... 16.6 ... 16.5 17.0 ... 17.1 ... 16.9 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ...18.7 ... 18.3 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Maindirection Sector Typically: 30 dB > 10 dB Typically: 30 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0° ±60° Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 7.7° 7.2° 5.0° 4.8° 4.6° Electrical tilt continuously adjustable 0°–7° 0°–7° 0°– 6° 0°– 6° 0°– 6° Sidelobe suppression for first 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 17 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Intermodulation IM3 < –150 dBc 200 W* Total power per combined input 450 W* Input 2 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1160 / 500 / 1210 N Height/width/depth 2533 / 261 / 146 mm Category of mounting hardware H (Heavy) Weight Scope of supply Integrated combiner 800/900 – 1800/2000/2600 XXPol 250 W* 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter The insertion loss is included in the given antenna gain values. 790–960 –45° 1710–2180 –45° 790–960 +45° * (at 50 °C ambient temperature) Max. power per input 1710–2180 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 109 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 88° 88° XXPol Panel 790–960/1710–2180 88°/ 88° 13.5/16.5dBi 0°–12°/0°–10°T s clamp d e d lu c in 80010121V01 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 13.4 ... 13.4 ... 13.1 13.6 ... 13.6 ... 13.4 13.9 ... 13.8 ... 13.5 16.4 ... 16.4 ... 16.2 16.4 ... 16.5 ... 16.0 16.4 ... 15.9 ... 15.3 0° ... 6° ... 12° 0° ... 6° ... 12° 0° ... 6° ... 12° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° ±60° 88° 86° 88° 82° 85° 90° > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB Typically: 17 dB > 10 dB avg. 16 dB Typically: 18 dB > 10 dB avg. 16 dB Typically: 20 dB > 13 dB avg. 19 dB Typically: 17 dB > 10 dB avg. 17 dB Typically: 16 dB > 12 dB avg. 19 dB Typically: 15 dB > 10 dB avg. 19 dB 15.0° 14.5° 14° 7.0° 6.6° 6.4° Vertical Pattern: Half-power beam width Electrical tilt 0.5°– 12.5°, continuously adjustable 0.5°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 14 ... 14 dB 16 ... 15 ... 14 dB 18 ... 16 ... 16 dB 17 ... 17 ... 16 dB 17 ... 18 ... 16 dB 18 ... 16 ... 16 dB average: 20 ... 19 ... 16 dB 20 ... 18 ... 17 dB 22 ... 20 ... 20 dB 20 ... 20 ... 18 dB 21 ... 22 ... 17 dB 20 ... 20 ... 16 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 42 dB (790 – 960 // 1710 – 2180 MHz) 800/900 – 1800/2000/2600 XXPol Intermodulation IM3 Max. power per input Total power < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 420 / 260 / 620 N Height/width/depth 1384 / 262 / 149 mm Category of mounting hardware M (Medium) Weight 21 kg / 23 kg (clamps incl.) Scope of supply 110 Panel and 2 units of clamps for 50 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2180 –45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 88° 88° XXPol Panel 790–960/1710–2180 88°/ 88° 15.2/18dBi 0°–10°/0°–6°T s clamp d e d lu c in 80010122V01 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 862 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 14.8 ... 14.8 ... 14.8 14.8 ... 15.0 ... 14.8 14.9 ... 15.1 ... 14.9 17.7 ... 17.8 ... 17.7 17.7 ... 18.0 ... 17.6 17.6 ... 17.8 ... 17.4 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection Sector 0° ±60° ±60° 88° 87° 88° 82° 85° 90° > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB Typically: 18 dB > 10 dB avg. 16 dB Typically: 18 dB > 10 dB avg. 16 dB Typically: 20 dB > 13 dB avg. 19 dB Typically: 17 dB > 10 dB avg. 17 dB Typically: 16 dB > 12 dB avg. 19 dB Typically: 15 dB > 10 dB avg. 19 dB 11 10.9° 10.5° 5.5° 5.2° 5° Vertical Pattern: Half-power beam width Electrical tilt 0°– 10°, continuously adjustable 0°– 6°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 18 ... 16 ... 14 dB 16 ... 16 ... 15 dB 16 ... 16 ... 15 dB 18 ... 18 ... 16 dB 18 ... 18 ... 16 dB 18 ... 18 ... 16 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 42 dB (790 – 960 // 1710 – 2180 MHz) Max. power per input Total power < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 800/900 – 1800/2000/2600 XXPol Intermodulation IM3 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 580 / 360 / 870 N Height/width/depth 1917 / 262 / 149 mm Category of mounting hardware M (Medium) Weight 27 kg / 29 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2180 –45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 111 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 X X 88° 88° XXPol Panel 790–960/1710–2180 88°/ 88° 16.5/18dBi 0°–7°/0°–6°T s clamp d e d lu c in 80010123V03 Type No. 790 – 862 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° Frequency range Polarization Average gain (dBi) Tilt 1710–2180 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.1 ... 16.2 ... 16.1 16.3 ... 16.4 ... 16.3 16.5 ... 16.6 ... 16.5 17.8 ... 17.7 ... 17.4 18.0 ... 17.9 ... 17.4 17.9 ... 17.8 ... 17.3 0° ... 4° ... 7° 0° ... 4° ... 7° 0° ... 4° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0° ±60° ±60° 86° 86° 86° 84° 85° 88° > 25 dB > 25 dB > 25 dB > 23 dB > 23 dB > 23 dB Typically: 18 dB > 10 dB avg. 16 dB Typically: 18 dB > 10 dB avg. 16 dB Typically: 20 dB > 13 dB avg. 19 dB Typically: 16 dB > 10 dB avg. 16 dB Typically: 16 dB > 12 dB avg. 17 dB Typically: 15 dB > 10 dB avg. 18 dB Tracking, Avg. Squint 0.5 dB 0.5 dB ±3.0° ±3.0° Vertical Pattern: Half-power beam width Electrical tilt 7.3° 7.2° 6.9° 4.8° 0.5°– 7°, continuously adjustable 4.5° 4.2° 0°– 6°, continuously adjustable Min. sidelobe suppression for 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 15 ... 14 ... 14 dB 15 ... 14 ... 14 dB 15 ... 14 ... 15 dB 18 ... 17 ... 16 dB 18 ... 17 ... 17 dB 18 ... 16 ... 17 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB Isolation: Intersystem > 45 dB (790 – 960 // 1710 – 2180 MHz) 800/900 – 1800/2000/2600 XXPol Intermodulation IM3 Max. power per input Total power < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Input 250 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 2 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 840 / 510 / 1260 N Height/width/depth 2635 / 262 / 149 mm Category of mounting hardware H (Heavy) Weight 33 kg / 35 kg (clamps incl.) Scope of supply 112 Panel and 2 units of clamps for 50 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2180 –45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Summary – Directional Antennas Triple-band 800/900 – 1800/2000/2600 Type XXXPol Panel Type No. Height [mm] Connector position Page 790–862 880–960 1710–2180 65° 65° 65° 15.5dBi 16dBi 18.5dBi 0°–10°T 0°–10°T 0°–6°T 80010698 1932 bottom 114 790–960 1710–1880 1920–2170 XXXPol Panel 790–960 1710–1880 1920–2170 XXXPol Panel 806–960 1710–2180 1710–2180 65° 65° 65° 65° 65° 65° 65° 65° 65° 15dBi 17dBi 17dBi 15dBi 16.5dBi 17dBi 15dBi 15dBi 15dBi 0°–14°T 0°–8°T 0°–8°T 0°–12°T 0°–8°T 0°–8°T 0°–14°T 0°–14°T 0°–14°T 742270V03 1384 bottom 115 80010670V01 1498 bottom 116 80010290V01 1540 bottom 117 65° 65° 65° 65° 65° 65° 65° 65° 65° 16.5dBi 18dBi 18dBi 16.5dBi 17.5dBi 18dBi 16.5dBi 16.5dBi 16.5dBi 0°–10°T 0°–6°T 0°–6°T 0°–10°T 0°–6°T 0°–6°T 2°–14°T 0°–14°T 0°–14°T 742271V03 1933 bottom 118 80010671V01 2058 bottom 119 80010291V02 2058 bottom 120 65° 65° 65° 66° 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 17.5dBi 17.5dBi 17.5dBi 17.5dBi 18dBi 18dBi 17.5dBi 17.5dBi 18dBi 17.5dBi 17.5dBi 17dBi 17.5dBi 17dBi 17dBi 2°–10°T 0°–10°T 0°–10°T 0°–7°T 0°–6°T 0°–6°T 0°–7°T 0°–6°T 0°–6°T 2°–10°T 0°–10°T 0°–10°T 4°–12°T 0°–14°T 0°–14°T 80010692 2593 bottom 121 742272V03 2533 bottom 122 80010672V01 2628 bottom 123 80010292V02 2694 bottom 124 80010492V01 2694 bottom 125 65° 65° 65° 16dBi 18dBi 18dBi 0°–10°T 0°–6°T 0°–6°T 80010675 1997 bottom 126 XXXPol Panel 790–960 1710–1880 1920–2170 XXXPol Panel 806–960 1710–1880 1920–2170 XXXPol Panel 790–960 1710–2180 1710–2180 C XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel 790–960 1710–2690 1710–2690 790–960 1710–1880 1920–2170 790–960 1710–1880 1920–2170 790–960 1710–2180 1710–2180 790–960 1710–2180 1710–2180 790–960 1710–2170 2490–2690 C C C = integrated Combiner New or changed product ying deplo s, When d Antenna ng n si a u b r Triple o conside biners Com e als pleas riple-band 1) T 2 2 l a speci (see page 113 800/900 – 1800/2000/2600 XXXPol Dual Polarization + 45°/ –45° Triple-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 1710 –2180 X X X 65° 65° 65° XXXPol Panel 790–862/880–960/1710–2180 65°/65°/ 65° 15.5/16/18.5dBi 0°–10°/0°–10°/0°–6°T Frequency range s clamp d e d lu c in 80010698 Type No. 790–862 880–960 1710–2180 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 15.1 ... 15.4 ... 15.1 15.6 ... 15.9 ... 15.4 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ...18.7 ... 18.3 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection 0° 25 dB 27 dB 25 dB 25 dB 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 1.0 dB 0.5 dB Squint ±2.5° ±2.5° ±2.5° Vertical Pattern: Half-power beam width 11.5° 10.1° 5.0° 4.8° 4.6° Electrical tilt 0°–10° 0°–10° 0°– 6° 0°– 6° 0°– 6° continuously adjustable Sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam: average: ≥ 17 ... 17 ... 17 dB ≥ 17 ... 17 ... 16 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB 800/900 – 1800/2000/2600 XXXPol VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 38 dB (790...960 // 1710 – 2180 MHz) > 30 dB (790 – 862 // 880 – 960 MHz) < –150 dBc < –150 dBc < –150 dBc 250 W* 500 W* 250 W* 500 W* 250 W* 500 W* 6 x 7-16 female (long neck) Bottom 3x, Position bottom continuously adjustable Frontal / lateral / rearside: 850 / 380 / 910 N 1932 / 269 / 154 mm M (Medium) 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter * (at 50 °C ambient temperature) 790–862 –45° 114 < 1.5 > 30 dB 880– 960 –45° 880– 960 +45° 7-16 7-16 790–862 +45° 1710 –2180 1710 –2180 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –1880 1920 –2170 X X X 65° ° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/ 65°/65° 15/17/17dBi 0°–14°/0°–8°/0°–8°T Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam avg. 790–960 790 – 862 MHz 880 – 960 MHz +45°, –45° +45°, –45° 14.4 ... 14.3 ... 14.0 14.8 ... 14.7 ... 14.2 0° ... 7° ... 14° 0° ... 7° ... 14° 68° > 30 dB Typically: 25 dB > 10 dB 1710 –1880 1710 – 1880 MHz +45°, –45° 16.8 ... 16.9 ... 16.6 0° ... 4° ... 8° 65° > 30 dB Typically: 25 dB > 10 dB 65° > 32 dB Typically: 25 dB > 10 dB 0.5 dB ±3.0° 1.0 dB ±2.0° 16.5° 15.3° 0°– 14° 0° ... 7° ... 14° T 0° ... 7° ... 14° T 17 ... 16 ... 15 dB 17 ... 18 ... 17 dB VSWR Isolation: Intrasystem Isolation: Intersystem 1920 –2170 1920 – 2170 MHz +45°, –45° 16.9 ... 17.0 ... 16.7 0° ... 4° ... 8° 7.4° 0°– 8° 0° ... 4° ... 8° T 17 ... 17 ... 16 dB 61° > 32 dB Typically: 25 dB > 10 dB 0.5 dB ±3.0° 6.7° 0°– 8° 0° ... 4° ... 8° T 16 ... 16 ... 15 dB < 1.5 < 1.5 > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz)11 Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz)11 > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc 500 W* 1000 W* 200 W* 200 W* 400 W* 400 W* 6x 7-16 female (long neck) Bottom 3x, Position bottom continuously adjustable Frontal / lateral / rearside: 600 / 270 / 640 N (at 150 km/h) 1384 / 261 / 146 mm M (Medium) 19 kg / 21 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 790–960 –45° 790–960 +45° 7-16 7-16 800/900 – 1800/2000/2600 XXXPol Frequency range s clamp d e d lu c in 742270V03 Type No. 1710–1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 115 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –1880 1920 –2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 C 65°/ 65°/65° 15/16.5/17dBi 0°–12°/0°–8°/0°–8°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam 790 – 866 MHz +45°, –45° 2 x 14.8 dBi 790 –960 824 – 894 MHz +45°, –45° 2 x 15 dBi 880 – 960 MHz +45°, –45° 2 x 15.2 dBi 69° 67° > 27 dB Typically: 25 dB > 10 dB 65° 14° 13.6° 0.5°– 12° 0° ... 6° ... 12° T 17 ... 17 ... 14 dB 13° VSWR Isolation: Intrasystem Isolation: Intersystem 1710 –1880 1920 –2170 1710 – 1880 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 16.5 dBi 2 x 17.2 dBi 66° > 25 dB Typically: 16 dB > 10 dB < –150 dBc 250 W 200 W (at 50 °C ambient temperature) 450 W (at 50 °C ambient temperature) Max. power per combined input Input 200 W 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 3 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 460 / 290 / 680 N Height/width/depth 1498 / 262 / 149 mm Category of mounting hardware M (Medium) Weight 21.5 kg / 23.5 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. 790–960 –45° 1920–2170 –45° 7-16 116 65° > 25 dB Typically: 18 dB > 10 dB 6.7° 6.2° 0.5°– 8° 0°– 8° 0° ... 4° ... 8° T 0° ... 4° ... 8° T 18 ... 16 ... 14 dB 18 ... 16 ... 15 dB < 1.5 > 30 dB Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 800/900 – 1800/2000/2600 XXXPol s clamp d e d lu c in 80010670V01 Type No. 1920–2170 +45° 7-16 790–960 +45° 1710–1880 –45° 1710–1880 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Triple-multiband Panel Dual Polarization Half-power Beam Width 806 – 960 1710 –2180 1710 –2180 X X X 65° 65° 65° XXXPol Panel 806–960/1710–2180/1710–2180 65°/ 65°/65° 15/15/15dBi 0°–14°/0°–14°/0°–14°T Polarization Gain: (dBi) 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt 806–960 806 – 866 MHz 824–894 MHz 880–960 MHz +45°, –45° +45°, –45° +45°, –45° 14.4 ... 14.3 ... 14 14.6 ... 14.4 ... 14.2 14.9 ... 14.7 ... 14.4 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 69° 68° > 25 dB Typically: 25 dB > 10 dB 67° 14.7° VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 67° 14.3° 13.9° 0°–14°, continuously adjustable Sidelobe suppression 0° ... 7° ... 14° – for first sidelobe above main beam 18 ... 16 ... 16 dB 0° ... 7° ... 14° 18 ... 16 ... 16 dB 14.5 ... 14.5 ... 14.2 14.8 ... 14.8 ... 14.5 15.1 ... 14.8 ... 14.4 14 ... 14 ... 13.7 14.4 ... 14.3 ... 13.9 14.9 ... 14.8 ... 14.2 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 18 ... 17 ... 16 dB 63° > 25 dB Typically: 20 dB > 10 dB 60° 13.8° 13.2° 12.6° Syst. bottom: 0°–14°, continuously adjustable Syst. top: 0°–14°, continuously adjustable 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 18 ... 16 ... 15 dB 18 ... 17 ... 17 dB 18 ... 16 ... 17 dB < 1.5 > 30 dB > 35 dB (806–960 // 1710–2180 MHz)11 > 30 dB (1710–2180 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable Frontal / lateral / rearside: 480 / 300 / 700 N 1540 / 262 / 149 mm M (Medium) 21 kg / 23 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° bottom 1710–2180 –45° top 806–960 –45° 7-16 7-16 800/900 – 1800/2000/2600 XXXPol Frequency range s clamp d e d lu c in 1710–2180 1710–2180 1710–1880 MHz 1850–1990 MHz 1920–2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010290V01 Type No. 1710–2180 +45° bottom 806–960 +45° 7-16 7-16 7-16 1710–2180 +45° top 7-16 For more information about additional mounting accessories please refer to page 186 117 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –1880 1920 –2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/ 65°/65° 16.5/18/18dBi 0°–10°/0°–6°/0°–6°T 742271V03 Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam avg. 790–960 790 – 862 MHz 880 – 960 MHz +45°, –45° +45°, –45° 15.9 ... 15.8 ... 15.6 16.4 ... 16.3 ... 15.9 0° ... 5° ... 10° 0° ... 5° ... 10° 68° > 27 dB Typically: 25 dB > 10 dB 800/900 – 1800/2000/2600 XXXPol 65° > 28 dB Typically: 25 dB > 10 dB 65° > 30 dB Typically: 25 dB > 10 dB 0.5 dB ±2.5° 1.5 dB ±2.5° 10.9° 10° 0°– 10° 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 15 ... 16 ... 17 dB ≥ 15 ... 18 ... 19 dB VSWR Isolation: Intrasystem Isolation: Intersystem 5.0° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 17 ... 15 dB 61° > 30 dB Typically: 25 dB > 10 dB 0.5 dB ±2.5° 4.6° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 16 dB < 1.5 < 1.5 > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz)11 Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz)11 > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc 300 W* 600 W* 200 W* 200 W* 400 W* 400 W* 6x 7-16 female (long neck) Bottom 3x, Position bottom continuously adjustable Frontal / lateral / rearside: 860 / 380 / 920 N 1933 / 261 / 146 mm M (Medium) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 118 1710 –1880 1710 – 1880 MHz +45°, –45° 17.8 ... 18.0 ... 17.8 0° ... 3° ... 6° s clamp d e d lu c in 1920 –2170 1920 – 2170 MHz +45°, –45° 17.9 ... 18.2 ... 17.9 0° ... 3° ... 6° 790–960 –45° 790–960 +45° 7-16 7-16 1710–1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Triple-band Panel Dual Polarization Half-power Beam Width 806 – 960 1710 –1880 1920 –2170 X X X 657° 65° 65° XXXPol Panel 806–960/1710–1880/1920–2170 C 65°/ 65°/65° 16.5/17.5/18dBi 0°–10°/0°–6°/0°–6°T Frequency range 806 – 866 MHz +45°, –45° 2 x 16 dBi 806 –960 824 – 894 MHz +45°, –45° 2 x 16.1 dBi 880 – 960 MHz +45°, –45° 2 x 16.3 dBi 69° 68° > 25 dB Typically: 25 dB > 10 dB 67° 9.5° 9.3° 0°– 10° 0° ... 5° ... 10° T 15 ... 15 ... 13 dB 9.0° VSWR Isolation: Intrasystem Isolation: Intersystem 1920 –2170 1710 –1880 1710 – 1880 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 17.5 dBi 2 x 18 dBi 65° > 24 dB Typically: 18 dB > 10 dB 4.7° 4.3° 0°– 6° 0°– 6° 0° ... 3° ... 6° T 0° ... 3° ... 6° T 18 ... 17 ... 16 dB 18 ... 16 ... 15 dB < 1.5 > 30 dB Typically: > 50 dB (806 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 65° > 25 dB Typically: 20 dB > 10 dB < –150 dBc 250 W 200 W (at 50 °C ambient temperature) 450 W (at 50 °C ambient temperature) Max. power per combined input Input 200 W 4 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 3 x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 640 / 400 / 950 N Height/width/depth 2058 / 262 / 149 mm Category of mounting hardware M (Medium) Weight 28 kg / 30 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 42 – 115 mm diameter Integrated combiner 800/900 – 1800/2000/2600 XXXPol Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam s clamp d e d lu c in 80010671V01 Type No. The insertion loss is included in the given antenna gain values. 806–960 –45° 1920–2170 –45° 7-16 1920–2170 +45° 7-16 806–960 +45° 1710–1880 –45° 1710–1880 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 119 Triple-multiband Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 1710 –2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/ 65°/65° 16.5/16.5/16.5dBi 2°–14°/0°–14°/0°–14°T Frequency range Polarization Average Gain: (dBi) 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 800/900 – 1800/2000/2600 XXXPol VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790–960 790 – 866 MHz 824–894 MHz 880–960 MHz +45°, –45° +45°, –45° +45°, –45° 16.2 ... 16 ... 15.7 16.3 ... 16.1 ... 15.8 16.4 ... 16.2 ... 15.8 2° ... 8° ... 14° 2° ... 8° ... 14° 2° ... 8° ... 14° 68° > 25 dB Typically: 25 dB > 10 dB 67° > 25 dB Typically: 25 dB > 10 dB 1.0 dB 65° > 25 dB Typically: 25 dB > 10 dB 10° 15.9 ... 15.9 ... 15.5 16.2 ... 16.2 ... 15.7 16.3 ... 16.3 ... 15.8 15.8 ... 15.8 ... 15.4 16.1 ... 16.1 ... 15.4 16.3 ... 16.2 ... 15.5 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 65° > 25 dB Typically: 18 dB > 10 dB 9.7° 9.3° 2°–14°, continuously adjustable 2 °... 8° ... 14° T 2° ... 8 °... 14° T 2° ... 8° ... 14° T 17 ... 17 ... 15 dB 17 ... 17 ... 16 dB 17 ... 17 ... 16 dB 64° > 25 dB Typically: 19 dB > 10 dB 1.0 dB 60° > 25 dB Typically: 20 dB > 10 dB 9.5° 9° 8.7° 0°–14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 18 ... 17 ... 17 dB 18 ... 17 ... 17 dB 18 ... 17 ... 17 dB < 1.5 > 30 dB > 35 dB (790–960 // 1710–2180 MHz)11 > 30 dB (1710–2180 // 1710–2180 MHz) < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 6 x 7-16 female (long neck) Bottom 3 x, Position bottom continuously adjustable Frontal / lateral / rearside: 640 / 400 / 950 N 2058 / 262 / 149 mm M (Medium) 27 kg / 29 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° bottom 120 s clamp d e d lu c in 1710–2180 1710–2180 1710–1880 MHz 1850–1990 MHz 1920–2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010291V02 Type No. 1710–2180 –45° top 790–960 –45° 7-16 7-16 1710–2180 +45° bottom 790–960 +45° 7-16 7-16 7-16 1710–2180 +45° top 7-16 For more information about additional mounting accessories please refer to page 186 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2690 1710 –2690 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2690/1710–2690 65°/ 65°/65° 17.5/17.5/17.5dBi 2°–10°/0°–10°/0°–10°T s clamp d e d lu c in 80010692 Type No. Frequency range Polarization Average Gain: (dBi) 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Tilt 790 – 866 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2690 1710–2690 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2200 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.6 ... 16.6 ... 16.5 16.9 ... 17.0 ... 16.8 17.3 ... 17.4 ... 17.2 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° 68° 67° 65° 17.0 ... 16.8 ... 16.5 17.5 ... 17.3 ... 17.0 17.7 ... 17.5 ... 17.2 17.5 ... 17.2 ... 17.0 16.6 ... 16.4 ... 16.1 17.1 ... 16.9 ... 16.6 17.3 ... 17.1 ... 16.8 17.0 ... 16.7 ... 16.5 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width 67° 65° 63° 62° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection Sector Typically: 28 dB > 10 dB Typically: 30 dB > 10 dB Typically: 32 dB > 10 dB Typically: 16 dB > 10 dB Typically: 18 dB > 10 dB Typically: 18 dB > 10 dB Typically: 20 dB > 10 dB 7.5° 7.3° 7.0° 7.1° 6.7° 6.3° 5.4°° 0° ±60° Vertical Pattern: Electrical tilt Min. sidelobe suppression for first sidelobe above main beam 2°–10°, continuously adjustable 0°–10°, continuously adjustable 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 16 ... 14 dB 18 ... 16 ... 15 dB 18 ... 17 ... 16 dB 16 ... 16 ... 15 dB 16 ... 16 ... 15 dB 16 ... 16 ... 15 dB 16 ... 16 ... 15 dB VSWR < 1.5 Isolation: Intrasystem > 30 dB > 28 dB Isolation: Intersystem > 40 dB (790–960 // 1710–2690 MHz)22 > 30 dB (1710–2690 // 1710–2690 MHz) Intermodulation IM3 Max. power per input Total power < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Input 200 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) 6 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 3x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1320 / 530 / 1400 N Height/width/depth 800/900 – 1800/2000/2600 XXXPol Half-power beam width 2593 / 299 / 152 mm Category of mounting hardware H (Heavy) Weight 33 kg / 35 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2690 1710–2690 +45° –45° 7-16 7-16 1710–2690 1710–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 121 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –1880 1920 –2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/ 65°/65° 17.5/18/18dBi 0°–7°/0°–6°/0°–6°T 742272V03 Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam avg. 790–960 790 – 862 MHz 880 – 960 MHz +45°, –45° +45°, –45° 16.9 ... 16.9 ... 16.8 17.3 ... 17.4 ... 17.2 0° ... 3° ... 7° 0° ... 3° ... 7° 68° > 30 dB Typically: 30 dB > 10 dB 800/900 – 1800/2000/2600 XXXPol 65° > 30 dB Typically: 30 dB > 10 dB 65° > 30 dB Typically: 25 dB > 10 dB 0.5 dB ±2.5° 1.0 dB ±2.5° 8.0° 7.2° 0°– 7° 0° ... 4° ... 7° T ≥ 17 ... 17 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem 0° ... 4° ... 7° T ≥ 18 ... 17 ... 15 dB 5.0° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 17 ... 15 dB 61° > 30 dB Typically: 25 dB > 10 dB 0.5 dB ±2.5° 4.6° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 16 dB < 1.5 < 1.5 > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz)11 Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz)11 > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc 500 W* 1000 W* 250 W* 250 W* 500 W* 500 W* 6x 7-16 female (long neck) Bottom 3x, Position bottom continuously adjustable Frontal / lateral / rearside: 1160 / 500 / 1210 N 2533 / 261 / 146 mm H (Heavy) 29 kg / 31 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 122 1710 –1880 1710 – 1880 MHz +45°, –45° 17.8 ... 18.0 ... 17.8 0° ... 3° ... 6° s clamp d e d lu c in 1920 –2170 1920 – 2170 MHz +45°, –45° 17.9 ... 18.2 ... 17.9 0° ... 3° ... 6° 790–960 –45° 790–960 +45° 7-16 7-16 1710–1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –1880 1920 –2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 C 65°/ 65°/65° 17.5/17.5/18dBi 0°–7°/0°–6°/0°–6°T Frequency range 790 – 866 MHz +45°, –45° 2 x 17 dBi 790 –960 824 – 894 MHz +45°, –45° 2 x 17.2 dBi 880 – 960 MHz +45°, –45° 2 x 17.5 dBi 69° 68° > 25 dB Typically: 25 dB > 10 dB 66° 7.4° 7.2° 0.5°– 7° 0° ... 4° ... 7° T 15 ... 16 ... 16 dB 6.8° VSWR Isolation: Intrasystem Isolation: Intersystem 1920 –2170 1710 –1880 1710 – 1880 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 17.5 dBi 2 x 18 dBi 65° > 25 dB Typically: 14 dB > 10 dB 4.7° 4.4° 0°– 6° 0°– 6° 0° ... 3° ... 6° T 0° ... 3° ... 6° T 17 ... 17 ... 16 dB 17 ... 15 ... 14 dB < 1.5 > 30 dB Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 63° > 25 dB Typically: 17 dB > 10 dB < –150 dBc 250 W 200 W (at 50 °C ambient temperature) 450 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 3 x, Position bottom continuously adjustable Frontal / lateral / rearside: 850 / 510 / 1270 N (at 150 km/h) 2628 / 262 / 149 mm H (Heavy) 32 kg / 34 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Max. power per combined input Input Connector position Adjustment mechanism Wind load Height/width/depth Category of mounting hardware Weight Scope of supply Integrated combiner 200 W The insertion loss is included in the given antenna gain values. 790–960 –45° 1920–2170 –45° 7-16 1920–2170 +45° 7-16 800/900 – 1800/2000/2600 XXXPol Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam s clamp d e d lu c in 80010672V01 Type No. 790–960 +45° 1710–1880 –45° 1710–1880 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 186 123 Triple-multiband Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 1710 –2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/ 65°/65° 17.5/17.5/17dBi 2°–10°/0°–10°/0°–10°T 80010292V02 Type No. s clamp d e d lu c in Frequency range 790–960 1710–2180 1710–2180 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average Gain: (dBi) 16.8 ... 17.0 ... 16.8 17.0 ... 17.1 ... 17.0 17.4 ... 17.4 ... 17.1 1710–2180 MHz (Syst. bottom) 16.5 ... 16.7 ... 16.5 17.0 ... 17.1 ... 16.7 17.3 ... 17.4 ... 16.8 1710–2180 MHz (Syst. top) 16.2 ... 16.3 ... 16.1 16.7 ... 16.7 ... 16.4 17.0 ... 17.0 ... 16.5 Tilt 2° ... 6° ... 10° 2° ... 6° ...1 0° 2° ... 6° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width 69° 68° 66° 65° 64° 60° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 26 dB > 26 dB > 26 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° 25 dB 25 dB 25 dB 18 dB 18 dB 18 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB ±60° avg. 20 dB avg. 20 dB avg. 17 dB avg. 14 dB avg. 16 dB avg. 16 dB Tracking, Avg. 1.0 dB 1710–2180 MHz (Syst. bottom) 1.0 dB 1710–2180 MHz (Syst. top) 0.5 dB Squint ±3.5° ±3.5° Vertical Pattern: Half-power beam width 7.8° 7.6° 7.1° 7.4° 7.2° 6.8° Electrical tilt 2.5°– 9.5°, continuously adjustable 0°– 10°, continuously adjustable Sidelobe suppression for first 2° ... 6° ... 10° T 2° ... 6° ... 10° T 2° ... 6° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T sidelobe above main beam 17 ... 16 ... 14 dB 17 ... 16 ... 14 dB 17 ... 16 ... 14 dB 16 ... 16 ... 16 dB 16 ... 17 ... 16 dB 16 ... 16 ... 14 dB 800/900 – 1800/2000/2600 XXXPol VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 > 30 dB < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 36 dB (790 – 960 // 1710 – 2180 MHz)11 > 36 dB (1710 – 2180 // 1710 – 2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable Frontal / lateral / rearside: 870 / 520 / 1320 N 2694 / 262 / 149 mm H (Heavy) 36 kg / 38 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° 1710–2180 +45° 1710–2180 1710–2180 +45° –45° 7-16 124 7-16 790–960 –45° 790–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Triple-multiband Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2180 1710 –2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/ 65°/65° 17.5/17/17dBi 4°–12°/0°–14°/0°–14°T Frequency range s clamp d e d lu c in 1710–2180 1710–2180 1710–1880 MHz 1850–1990 MHz 1920–2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010492V01 Type No. 790–960 790 – 866 MHz 824–894 MHz 880–960 MHz +45°, –45° +45°, –45° +45°, –45° 16.6 ... 16.5 ... 16.3 17.0 ... 16.9 ... 16.5 17.2 ... 17.0 ... 16.7 Polarization Average Gain: (dBi) 1710–2180 MHz (Syst. bottom) 16.1 ... 16.3 ... 16.0 16.7 ... 16.8 ... 16.3 17.0 ...17.0 ... 16.6 1710–2180 MHz (Syst. top) 16.1 ...16.1 ... 15.8 16.7 ... 16.5 ... 16.2 17.0 ... 16.9 ... 16.4 Tilt 4° ... 8° ... 12° 4° ... 8° ... 12° 4° ... 8° ... 12° 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° Horizontal Pattern: Half-power beam width 68° 67° 66° 65° 63° 60° Front-to-back ratio (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° 23 dB 24 dB 25 dB 18 dB 18 dB 19 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 7.5° 7.4° 7.2° 7.8° 7.6° 7.2° Electrical tilt 4°–12°, continuously adjustable 0°–14°, continuously adjustable Sidelobe suppression 4° ... 8° ... 12° T 4° ... 8° ... 12° T 4° ... 8° ... 12° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T – for first sidelobe above main beam 19 ... 17 ... 16 dB 19 ... 18 ... 18 dB 19 ... 18 ... 18 dB 18 ... 17 ... 15 dB 18 ... 17 ... 15 dB 18 ... 17 ... 15 dB – within 0°–20° sector above horizon 15 ... 15 ... 14 dB 16 ... 15 ... 14 dB 16 ... 15 ... 14 dB 18 ... 17 ... 15 dB 17 ... 17 ... 15 dB 15 ... 14 ... 14 dB Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB > 36 dB (790–960 // 1710–2180 MHz)11 > 36 dB (1710–2180 // 1710–2180 MHz) < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 6 x 7-16 female (long neck) Bottom 3x, Position bottom continuously adjustable Frontal / lateral / rearside: 870 / 520 / 1320 N 2694 / 262 / 149 mm H (Heavy) 34 kg / 36 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° bottom 1710–2180 –45° top 790–960 –45° 7-16 7-16 800/900 – 1800/2000/2600 XXXPol VSWR Isolation: Intrasystem Isolation: Intersystem 1710–2180 +45° bottom 790–960 +45° 7-16 7-16 7-16 1710–2180 +45° top 7-16 For more information about additional mounting accessories please refer to page 186 125 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 –2170 2490–2690 X X X 65° ° 65° 65° XXXPol Panel 790–960/1710–2170/2490–2690 65°/ 65°/65° 16/18/18dBi 0°–10°/0°–6°/0°–6°T s clamp d e d lu c in 80010675 Type No. Frequency range Polarization Average gain (dBi) Tilt 790 – 866 MHz 790–960 824 – 896 MHz +45°, –45° +45°, –45° 1710–2170 2490–2690 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.0 ... 16.0 ... 15.5 16.1 ... 16.1 ... 15.6 16.0 ... 16.2 ... 15.6 18.0 ... 18.0 ... 17.6 18.0 ... 18.0 ... 17.5 18.1 ... 18.1 ... 17.4 17.8 ... 17.8 ... 17.6 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 67° 65° 62° 63° 62° 63° Front-to-back ratio, copolar (180°±30°) > 27 dB > 27 dB > 27 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection Sector Typically: 22 dB > 10 dB Typically: 22 dB > 10 dB Typically: 22 dB > 10 dB Typically: 18 dB > 10 dB Typically: 22 dB > 10 dB Typically: 23 dB > 10 dB Typically: 25 dB > 10 dB 10.3° 10.1° 9.8° 4.8° 4.6° 4.4° 3.5° 0° ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjust. Min. sidelobe suppression for first sidelobe above main beam 0°–10° 0°–6° VSWR Isolation: Intrasystem < 1.5 < 1.5 < 1.5 > 30 dB > 28 dB > 28 dB Isolation: Intersystem > 30 dB (790–960 // 1710–2170 // 2490–2690 MHz) Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input Total power 500 W* 1000 W* 200 W* 400 W* Input 200 W* 400 W* 6 x 7-16 female (long neck) Connector position Bottom Adjustment mechanism 3x, Position bottom continuously adjustable Wind load (at 150 km/h) Frontal / lateral / rearside: 1020 / 390 / 1050 N Height/width/depth 1997 / 300 / 152 mm Category of mounting hardware 800/900 – 1800/2000/2600 XXXPol 0°–6° 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 17 ... 15 dB 18 ... 18 ... 16 dB 18 ... 18 ... 16 dB 18 ... 16 ... 16 dB 18 ... 18 ... 17 dB 18 ... 17 ... 17 dB 18 ... 18 ... 18 dB M (Medium) Weight 26 kg / 28 kg (clamps incl.) Scope of supply Panel and 2 units of clamps for 50 – 115 mm diameter * (at 50 °C ambient temperature) 1710–2170 –45° 126 790–960 –45° 790–960 +45° 7-16 7-16 1710–2170 +45° 2490–2690 2490–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 186 Summary – Omnidirectional Antennas 800/900/1800/2000 Vertical Polarization – 800/900 Type Type No. Connector Height female [mm] Remarks Page VPol Omni VPol Omni 870–960 806–960 360° 360° 2dBi 2dBi 0°T 0°T 738450 K751161 N N 180 348 indoor/outdoor 128 129 VPol Omni 890–960 360° 5dBi 0°T K7515641 N 715 130 VPol Omni 870–960 360° 8dBi 0°T 736350 7-16 1543 131 VPol Omni VPol Omni VPol Omni 806–894 870–960 870–960 360° 360° 360° 11dBi 11dBi 10.5dBi 0°T 0°T 5°T 738192 736347 736349 7-16 7-16 7-16 3237 3033 2954 132 133 134 Vertical Polarization – Dual-band VVPol Omni 790–862 360° 870–960 360° 8dBi 9dBi 0°T 0°T 80010747 7-16 3237 VPol Omni 870–960/1710–1880 360° 2dBi 0°T 738449 N 216 indoor/outdoor 151 VPol Omni 824–960/1805–2170 360° 2dBi 0°T 80010147 N 216 indoor/outdoor 153 870–960 360° 1920–2170 360° 9dBi 10dBi 0°T 0°T 80010274 7-16 3033 separate inputs 136 VVPol Omni 870–960/1710–1880 360° 1920–2170 360° 2dBi 2dBi 0°T 0°T 80010111 N 493 separate inputs 137 11dBi 0°T 738187 7-16 1568 138 VVPol Omni separate inputs 135 VPol Omni 1710–1880 360° Omni VPol Vertical Polarization – 1800 Vertical Polarization – 1800/2000/2500/3500 VPol Omni 1710–2700 360° 2 dBi 0°T 80010431 N 115 indoor/outdoor 152 VPol Omni 1920–2170 360° 11 dBi 0°T 741790 7-16 1387 139 VPol Omni 2500–2700 360° 11dBi 0°T 80010442 7-16 1132 140 New or changed product 127 Omnidirectional Antenna Vertical Polarization Indoor and outdoor use 870 – 960 V VPol Omni 870–960 360° 2dBi 738450 Type No. Input N female Connector position Bottom or top Frequency range 870 – 960 MHz VSWR < 1.5 Gain 2 dBi Impedance 50 Ω < –150 dBc (2 x 43 dBm carrier) Polarization Vertical Max. power 100 W (at 50 °C ambient temperature) Weight 200 g Radome diameter 20 mm Height 180 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. Omni VPol 78° 3 dB 10 0 Vertical Pattern 128 180 mm Intermodulation IM3 Omnidirectional Antenna Vertical Polarization 806 – 960 V VPol Omni 806–960 360° 2dBi K751161 Type No. Frequency range 806 – 960 MHz Polarization Vertical 2 dBi Impedance 50 Ω VSWR < 1.5 Intermodulation IM3 348 mm Gain < –150 dBc (2 x 37 dBm carrier) Max. power 100 W (at 50 °C ambient temperature) Mounting: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 – 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 – 54 mm diameter (connecting cable runs outside the mast). Material: Radiator: Brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. Omni VPol 78° 3 dB 10 0 Vertical Pattern Mechanical specifications Input Connector position Bottom Weight 0.74 kg Radome diameter Wind load Max. wind velocity Packing size On the tip Laterally at the tip Brackets for side mounting (see page 198 – 200) N female Height 21 mm 17 N (at 150 km/h) 200 km/h 455 x 112x 97 mm 348 mm 129 Omnidirectional Antenna Vertical Polarization 890 – 960 V VPol Omni 890–960 360° 5dBi K7515641 Type No. Frequency range 890 – 960 MHz Polarization Vertical Gain 5 dBi Impedance 50 Ω VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 37 dBm carrier) 250 W (at 50 °C ambient temperature) Mounting: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 – 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 – 54 mm diameter (connecting cable runs outside the mast). Material: Radiator: Brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 715 mm Max. power Omni VPol 30° 3 dB 10 0 Vertical Pattern Mechanical specifications Input N female Connector position Bottom Weight 0.90 kg Radome diameter Wind load Max. wind velocity Packing size On the tip 130 Laterally at the tip Height 21 mm 20 N (at 150 km/h) 200 km/h 825 x 112 x 97 mm 715 mm Brackets for side mounting (see page 198 – 200) Omnidirectional Antenna Vertical Polarization 870 – 960 V VPol Omni 870–960 360° 8dBi Type No. 736350 Frequency range 870 – 960 MHz Polarization Vertical Gain 8 dBi Impedance 50 Ω VSWR < 1.5 < –150 dBc (2 x 43 dBm carrier) Max. power 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1543 mm Intermodulation IM3 Omni VPol 13° 3 dB 10 0 Vertical Pattern Mechanical specifications Input 150 230 um maximtop mast Connector position Bottom Weight 5.5 kg Radome diameter Wind load Max. wind velocity Packing size 104 Brackets for side mounting (see page 198 – 200) 7-16 female Height 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1543 mm 131 Omnidirectional Antenna Vertical Polarization 806 – 894 V VPol Omni 806–894 360° 11dBi Type No. 738192 Frequency range 806 – 894 MHz Polarization Vertical Gain 11 dBi Impedance 50 Ω VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3237 mm Max. power Omni VPol 7° 3 dB 10 0 Vertical Pattern Mechanical specifications Input 150 230 um maximtop mast 7-16 female Connector position Bottom Weight 8.5 kg Radome diameter Wind load Max. wind velocity Packing size 104 132 Height 51 mm 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm Brackets for side mounting (see page 198 – 200) Omnidirectional Antenna Vertical Polarization 870 – 960 V VPol Omni 870–960 360° 11dBi Type No. 736347 Frequency range 870 – 960 MHz Polarization Vertical Gain 11 dBi Impedance 50 Ω VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3033 mm Max. power Omni VPol 7° 3 dB 10 0 Vertical Pattern Mechanical specifications Input um maximtop mast Connector position 150 230 Weight Radome diameter Wind load Max. wind velocity Packing size 104 Brackets for side mounting (see page 198 – 200) Height 7-16 female Bottom 8 kg 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 3033 mm 133 Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt 870 – 960 V 5° VPol Omni 870–960 360° 10.5dBi 5°T Type No. 736349 Frequency range 870 – 960 MHz Polarization Vertical Gain 10.5 dBi Electrical tilt 5°, fixed Impedance 50 Ω VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 2954 mm Max. power Omni VPol 7° 3 dB 10 0 Vertical Pattern 5° electrical downtilt Mechanical specifications Input um maximtop mast 7-16 female Connector position 150 230 Weight 8 kg Radome diameter Wind load Max. wind velocity Packing size 104 134 Height Bottom 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 2954 mm Brackets for side mounting (see page 198 – 200) Dual-band OmniAntenna Vertical Polarization 870 – 960 790 – 862 V V VVPol Omni 870–960/790–862 360°/360° 9/8dBi 80010747 Type No. Frequency range Polarization Gain Half-power beam width Top system 870 – 960 MHz Bottom system 790 – 862 MHz Vertical Vertical 9 dBi 8 dBi Horizontal: Omni Vertical: 11° Horizontal: Omni Vertical: 16° Isolation, between ports > 30 dB Impedance 50 Ω < 1.5 < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 150 W 100 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductors of both systems are coupled capacitively. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 790 – 862 870 – 960 VPol 790 – 862 VPol 7-16 7-16 Omni VPol 870 – 960 3237 mm VSWR 11° 16° 10 dB 3 dB 10 3 0 0 Vertical Pattern Mechanical specifications Vertical Pattern 123 Input 48 Connector position 40 85 Weight Wind load 240 maximum mast top 150 Max. wind velocity Packing size Bottom view Height Radome diameter 10 870–960 MHz top system 2 x 7-16 female Bottom 8 kg 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm 51 mm 790–862 MHz bottom system 4 Layout of interface Brackets for side mounting (see page 198 – 200) 135 Dual-band Omni Antenna Vertical Polarization 870 – 960 1920 – 2170 V V VVPol Omni 870–960/1920-2170 360°/360° 9/10dBi 80010274 Type No. Frequency range Polarization Gain Half-power beam width Top system 870 – 960 MHz Bottom system 1920 – 2170 MHz Vertical Vertical 9 dBi 10 dBi Horizontal: Omni Vertical: 11° Horizontal: Omni Vertical: 9° Isolation, between ports > 30 dB Impedance 50 Ω < 1.5 < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 150 W 100 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductors of both systems are coupled capacitively. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1920 – 2170 Omni VPol 870 – 960 3033 mm VSWR 11° 9° 3 0 870 – 960 VPol 1920 –2170 VPol 7-16 7-16 dB 3 10 dB 10 0 Vertical Pattern Vertical Pattern 123 Mechanical specifications 48 2 x 7-16 female Connector position Weight Bottom view Max. wind velocity Packing size 10 870–960 MHz top system 1920–2170 MHz bottom system 4 Bottom 8 kg Wind load 240 maximum mast top 150 40 85 Input Height 210 N (at 150 km/h) 200 km/h 3380 x 148 x 112 mm 3033 mm Radome diameter 51 mm Layout of interface 136 Brackets for side mounting (see page 198 – 200) Multi-band Omni Antenna 870 – 960 1710 –1880 1920 – 2170 V V Vertical Polarization VVPol Omni 870–960/1710–1880/1920-2170 360°/360° 2/2dBi 80010111 Gain Isolation, between ports System Bottom: 1920 – 2170 MHz Vertical Vertical 2 dBi 2 dBi > 25 dB > 25 dB Impedance 50 Ω 50 Ω VSWR < 1.7 < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power per input 50 W (at 50 °C ambient temperature) Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit and screws: Stainless steel. Mounting: The antenna can be attached laterally at the tip of a tubular mast of 40 – 70 mm diameter with a mounting clamp supplied with the antenna. The connecting cables (not supplied) run outside the mast. Excellent grounding: The metal parts of the antenna and the mounting kit (exclusive the inner conductor of the upper unit) are DC grounded. 78° 870 – 960 1710 –1880 Top 1920 – 2170 Bottom N N 3 dB 10 Omni VPol Polarization System Top: 870 – 960 MHz 1710 – 1880 MHz 493 mm Frequency range 130 mm Type No. 0 Vertical Pattern Mechanical specifications Input VPol VPol 806–960 1710–1880 1920–2170 Connector position Bottom Weight 0.85 kg Wind load Max. wind velocity bottom system top system Packing size Layout of interface 2 x N female 30 N (at 150 km/h) 200 km/h 665 x 112 x 97 mm Height 493 mm Radome diameter 30 mm Bottom view 137 Omnidirectional Antenna Vertical Polarization 1710–1880 V VPol Omni 1710–1880 360° 11dBi 738187 Type No. Frequency range 1710 – 1880 MHz Polarization Vertical Gain 11 dBi Impedance 50 Ω VSWR < 1.3 < –150 dBc (2 x 43 dBm carrier) Max. power 1568 mm Intermodulation IM3 200 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. Omni VPol 7° 3 dB 10 0 Vertical Pattern Mechanical specifications Input 150 230 um maximtop mast 7-16 female Connector position Bottom Weight 5.5 kg Radome diameter Wind load Max. wind velocity Packing size 104 138 Height 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1568 mm Brackets for side mounting (see page 198 – 200) Omnidirectional Antenna Vertical Polarization 1920–2170 V VPol Omni 1920–2170 360° 11dBi 741790 Type No. Frequency range 1920 – 2170 MHz Polarization Vertical Gain 11 dBi Impedance 50 Ω VSWR < 1.5 < –150 dBc (2 x 43 dBm carrier) Max. power 150 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with one U-bolt bracket supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1387 mm Intermodulation IM3 Omni VPol 7° 3 dB 10 0 Vertical Pattern Mechanical specifications Input 130 um maximtop mast Connector position Weight Radome diameter Wind load 104 Max. wind velocity Packing size Height Brackets for side mounting (see page 198 – 200) 7-16 female Bottom 5 kg 51 mm 120 N (at 150 km/h) 200 km/h 1570 x 148 x 112 mm 1387 mm 139 Omnidirectional Antenna Vertical Polarization 2500–2700 V VPol Omni 2500–2700 360° 11dBi 0°T 80010442 Type No. Frequency range 2500 – 2700 MHz Polarization Vertical Gain 11 dBi Impedance 50 Ω VSWR < 1.5 < –150 dBc (2 x 43 dBm carrier) Max. power 1132 mm Intermodulation IM3 200 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with one U-bolt bracket supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. Omni VPol 7° 3 dB 10 0 Vertical Pattern Mechanical specifications Input 7-16 female Connector position 130 um maximtop mast Weight 4.5 kg Radome diameter 51 mm Wind load Max. wind velocity 104 Packing size Height 140 Bottom 110 N (at 150 km/h) 200 km/h 1232 x 148 x 112 mm 1132 mm Brackets for side mounting (see page 198 – 200) Summary – Indoor Antennas 806 ... 6000 Vertical Polarization Indoor – Directional Type Type No. Frequency range Connector female Page VPol BiDir 65° 5dBi 738446 790–960/1710–2170 N 50 VVPol Indoor 90° 7dBi 80010465 790–960/1710–2700 N 142 VPol Indoor 90° 7dBi 80010433 3300–3800 SMA 143 790–960/1710–2700 2xN 144 Indoor – Directional Dual Polarization VXPol Indoor 90° C 7dBi 80010677 Indoor – Multi-band Omnidirectional VPol Indoor 360° 2dBi 80010748 876–960/1710–2700 N 145 VPol Indoor 360° 2dBi 80010749 876–960/1710–2700 N 146 VPol Indoor 360° 2dBi 80010249 790–960/1425–3800/5150–6000 N 147 VPol Indoor 360° 2dBi 741573 1710–2700 N 148 VPol Indoor 360° 2dBi 80010430 1710–6000 N 149 80010709 790–960/1710–2700/2500–2700 2xN 150 Indoor – Omnidirectional Dual Polarization VHPol Indoor 360° 2dBi VPol Omni 360° 2dBi 738450 870–960 N 128 VPol Panel 90° 7.5dBi 736854 872–960 N 54 Indoor VPol, VXPol, VHPol Indoor / Outdoor – Single-band Indoor / Outdoor – Dual-band / Multi-band VPol Omni 360° 2dBi 738449 870–960/1710–1880 N 151 VPol Omni 360° 2dBi 80010431 1710–2700 N 152 VPol Omni 360° 2dBi 80010147 824–960/1805–2170 N 153 New or changed product 141 Indoor Multi-band Directional Antenna Vertical Polarization Half-power Beam Width Integrated Combiner 790 – 960 1710 –2700 V V 90° 90° C VVPol Indoor 790–960/1710–2700 C 90° 7dBi 80010465 Type No. Frequency range 790 – 960 MHz / 1710 – 2700 MHz Polarization Vertical Gain Approx. 7 dBi Half-power beam width Horizontal: Approx. 90° Impedance 50 Ω VSWR Max. power Input 790 – 806 MHz: < 2.2 806 – 960 MHz: < 2.0 1710 – 2700 MHz: < 2.0 50 W (at 50 °C ambient temperature) Cable RG 223/CU of 1m length, white, with N female connector Protection class IP 30 Weight 500 g Packing size 363 x 152 x 62 mm Height/width/depth 231 / 140 / 50 mm Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Mounting: Two holes of 6 mm diameter in the mounting plate. Screws are not supplied. Avoid stressing the cable. No stress on the hexagonal crimp. Minimum cable bending radius: 30 mm without tensile load. 1710–2700 VPol 790–960 VPol C N 7-16 90° Indoor VPol, VXPol, VHPol All metal parts inclusive the inner conductor are DC grounded. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (790 – 2500 MHz). 3 dB 10 Grounding: 0 Horizontal Pattern Mounting: Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated. 142 Align the antenna over the attachment plate. Pull the antenna to the stop. Indoor Directional Antenna Vertical Polarization Half-power Beam Width 3300–3800 V 90° VPol Indoor 3300–3800 90° 7dBi 80010433 Type No. Frequency range 3300 – 3800 MHz Polarization Vertical Gain Approx. 7 dBi Half-power beam width Horizontal: Approx. 90° Impedance 50 Ω VSWR < 2.0 Max. power Input 50 W (at 50 °C ambient temperature) Cable of 1 m length with SMA female connector Diameter / depth 111 x 23 mm Material: Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Mounting: One hole of 6 mm diameter in the mounting plate. Screws are not supplied. Avoid stressing the cable. Cable: Minimum bending radius: Single bending 10 mm, repeated bending 20 mm. 90° 3 dB 10 0 Horizontal Pattern Indoor VPol, VX Pol, VHPol Mounting: Attach the mounting plate to the wall using one screw of 6 mm diameter in the position as indicated. Align the antenna over the mounting plate. Antenna can be mounted in 90 degree steps as indicated. Pull the antenna to the stop. 143 Indoor Multi-band Directional Antenna Vertical / Dual Polarization Half-power Beam Width Integrated Combiner 790 – 960 1710 –2700 1710 –2700 V X (–45°) X (+45°) 90° 90° 90° C VXPol Indoor 790–960/1710–2700 C 90° 7dBi 80010677 Type No. 790 – 960 MHz 1710 – 2700 MHz Vertical +45°, –45° Approx. 7 dBi Approx. 2 x 7 dBi Polarization Gain Half-power beam width Horizontal: Approx. 90° Impedance 50 Ω VSWR < 2.0 Isolation, between ports Max. power Input > 25 dB 50 W (at 50 °C ambient temperature) 2 x Cable RG 223/CU of 1m length, white, with N female connector Protection class IP 30 Weight 600 g Packing size 363 x 152 x 62 mm Height/width/depth 232 / 140 / 50 mm Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Mounting: Two holes of 6 mm diameter in the mounting plate. Screws are not supplied. Avoid stressing the cable. No stress on the hexagonal crimp. Minimum cable bending radius: 30 mm without tensile load. Available accessories: Broadband power splitters and tappers (790 – 2700 MHz). 1710–2700 XPol –45° 790–960 VPol 1710–2700 XPol +45° C N N 90° 10 3 dB Frequency range 0 Indoor VPol, VXPol, VHPol Horizontal Pattern Mounting: Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated. 144 Align the antenna over the attachment plate. Pull the antenna to the stop. Indoor Multi-band Omni Antenna Vertical Polarization 1710 –2700 V The antenna needs no additional groundplane. VPol Indoor 876–960/1710–2700 360° 2dBi ∅ 210 mm 80010748 Type No. Frequency range 876 – 960 MHz 1710 – 2700 MHz Polarization Vertical Gain 2 dBi Impedance 50 Ω VSWR 876 – 890 – 1710 – 2170 – Max. power (per band) 890 MHz: < 2.0 960 MHz: < 1.7 2170 MHz: < 1.6 2700 MHz: < 2.0 50 W (at 50 °C ambient temperature) Input 1 x N female Weight 300 g Diameter 210 mm Height 78 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters and tappers (800 – 2700 MHz). min. dia. 35 mm Indoor VPol, VX Pol, VHPol ● 876 – 960 3 holes dia. 5 mm dia. 160 mm N connector, female 13 mm Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 145 Indoor Multi-band Omni Antenna Vertical Polarization ● 876 – 960 1710 –2700 V The antenna needs no additional groundplane. VPol Indoor 876–960/1710–2700 360° 2dBi ∅ 215 mm 80010749 Type No. Frequency range 876 – 960 MHz 1710 – 2700 MHz Polarization Vertical Gain 2 dBi Impedance 50 Ω VSWR 876 – 890 – 1710 – 2170 – Max. power (per band) 890 MHz: < 2.0 960 MHz: < 1.7 2170 MHz: < 1.6 2700 MHz: < 2.0 50 W (at 50 °C ambient temperature) Input 1 x N female Weight 340 g Diameter 215 mm Height 85 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters and tappers (800 – 2700 MHz). Indoor VPol, VXPol, VHPol min. dia. 35 mm 3 holes dia. 5 mm dia. 160 mm N connector, female 13 mm 146 Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. Indoor Multi-band Omni Antenna Vertical Polarization 790 – 960 1425–3800 5150–6000 V ● The antenna can be operated in all frequency ranges simultaneously. ● The antennas need no additional groundplane. VPol Indoor 790–960/1425–3800/5150–6000 360° 2dBi 80010249 Type No. Frequency range 790 – 960 MHz 1425 – 3800 MHz 5150 – 6000 MHz Polarization Vertical Gain ≈ 2 dBi Impedance 50 Ω VSWR 790 806 1425 1710 2200 5150 Max. power – – – – – – 806 960 1710 2200 3800 6000 MHz: MHz: MHz: MHz: MHz: MHz: < < < < < < 1.7 1.5 2.0 1.4 1.6 2.2 50 W (at 50 °C ambient temperature) Input 1 x N female Protection class IP 30 Weight 466 g Packing size 277 x 277 x 169 mm Diameter 258 mm Height 94 mm (without connector) Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (790 – 2500 MHz). Indoor VPol, VX Pol, VHPol min. dia. 35 mm dia. 160 mm 3 holes dia. 5 mm N connector, female Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 147 Indoor Omnidirectional Antenna Vertical Polarization Multi-band 1710 –2700 V ● The antenna can be operated in the total frequency range simultaneously. ● The antenna needs no additional groundplane. VPol Indoor 1710–2700 360° 2dBi 100 mm diameter 741573 Type No. Frequency range 1710 – 2700 MHz VSWR 1710 1850 1920 2170 2500 – – – – – 1880 1990 2170 2500 2700 MHz: MHz: MHz: MHz: MHz: Input 1 x N female Gain 2 dBi Impedance 50 Ω Polarization < < < < < 1.6 1.6 1.6 2.0 2.2 Vertical Max. power (per band) 50 W (at 50 °C ambient temperature) Weight 150 g Diameter 100 mm Height 50 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Holes in the base enable a mounting on the ceiling. Screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (790 – 2500 MHz). min. dia. 35 mm 80 mm Indoor VPol, VXPol, VHPol 2 holes dia. 5 mm N connector, female 12.9 mm Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 148 Indoor Omnidirectional Antenna Vertical Polarization Multi-band 1710 – 6000 V ● The antenna can be operated in all frequency ranges simultaneously. ● The antenna needs no additional groundplane. VPol Indoor 1710–6000 360° 2dBi 80010430 Type No. Frequency range 1710 – 6000 MHz Polarization Vertical Gain 2 dBi Impedance 50 Ω VSWR < 1.5 50 W (at 50 °C ambient temperature) Input 1 x N female Protection class IP 30 Weight 133 g Diameter Height 138 mm 56 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Holes in the base enable a mounting on the ceiling. Screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Available accessories: Broadband power splitters and tappers (800 – 2500 MHz). min. dia. 35 mm 2 holes dia. 5 mm N connector, female Indoor VPol, VX Pol, VHPol Max. power dia. 88 mm Clip the protective housing into position after the antenna has been mounted with the help of two supplied screws. 149 Indoor Multi-band Omni Antenna Dual Polarization 790 – 960 1710–2700 2500–2700 V H ● The antenna can be operated in all frequency ranges simultaneously. ● The antennas need no additional groundplane. VHPol Indoor 790–960/1710–2700/2500–2700 360° 2dBi 80010709 Type No. Frequency range Polarization 790 – 960 MHz 1710 – 2700 MHz 2500 – 2700 MHz Vertical Horizontal Gain ≈ 2 dBi Impedance 50 Ω VSWR 790 – 960 MHz: < 2.0 1710 – 2700 MHz: < 2.0 Isolation 2500 – 2700 MHz: < 2.0 > 30 dB Max. power 50 W (at 50 °C ambient temperature) Input 2 x N female Protection class IP 30 Weight Approx. 500 g Packing size 277 x 277 x 169 mm Diameter 258 mm Height 94 mm (without connector) Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connectors a hole in the ceiling is required. Available accessories: 790–960 1710–2700 VPol 2500–2700 HPol N N Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). Indoor VPol, VXPol, VHPol min. Ø 65 mm 30 mm dia. 160 mm 3 holes dia. 5 mm N connector, female Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 150 Dual-band Omni Antenna Vertical Polarization Indoor and outdoor use 870 – 960 / 1710–1880 V VPol Omni 870–960/1710–1880 360° 2dBi 738449 Type No. Input 1 x N female Connector position Bottom or top Frequency range 870 – 960 MHz / 1710 – 1880 MHz VSWR < 1.7 Gain 2 dBi Impedance 50 Ω < –150 dBc Polarization Vertical Max. power 50 W: 870 – 960 MHz 50 W: 1710 – 1880 MHz (at 50 °C ambient temperature) Weight 250 g Radome diameter 20 mm Height 216 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. 216 mm Intermodulation IM3 (2 x 43 dBm carrier) 78° dB 3 Indoor VPol, VX Pol, VHPol 10 0 Vertical Pattern 151 Omnidirectional Antenna Vertical Polarization Indoor and outdoor use 1710–2700 V VPol Omni 1710–2700 360° 2dBi 80010431 Type No. Input N female Connector position Bottom or top 1710 – 2700 MHz VSWR < 1.8 Gain 2 dBi Impedance 50 Ω Intermodulation IM3 (2 x 43 dBm carrier) < –150 dBc Polarization Vertical Max. power 50 W (at 50 °C ambient temperature) Weight 150 g Radome diameter 20 mm Height 115 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. Grounding: All metal parts of the antenna and the mounting kit are DC grounded. The inner conductor is not DC grounded. 78° 3 dB Indoor VPol, VXPol, VHPol 10 0 Vertical Pattern 152 115 mm Frequency range Dual-band Omni Antenna Vertical Polarization Indoor and outdoor use 824 – 960 /1805 –2170 V VPol Omni 824–960/1805–2170 360° 2dBi 80010147 Type No. Input 1 x N female Connector position Bottom or top 824 – 960 MHz / 1805 – 2170 MHz VSWR < 2.0 Gain 2 dBi Impedance 50 Ω Polarization Vertical Max. power 50 Watt: 824 – 960 MHz 50 Watt: 1805 – 2170 MHz (at 50 °C ambient temperature) Weight 250 g Radome diameter 20 mm Height 216 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 216 mm Frequency range 78° dB 3 Indoor VPol, VX Pol, VHPol 10 0 Vertical Pattern 153 154 Summary – Remote Electrical Tilt (RET) Type Type No. Page Kathrein’s Remote Electrical Tilt System General information 156 Data sheets of RET components Slimline Remote Control Unit (RCU) 86010147 / 86010148 158 Central Control Unit (CCU) for indoor use 86010006 / 86010026 159 Central Control Unit (CCU) for indoor use (cost efficient version) 86010140 / 86010141 160 Portable Control Adapter (PCA) 86010046 161 Power Supply and Signal Cable 86010007, ... 162 DC Power and Signal Splitter 86010002 163 Lightning Protection Device 86010030 164 Earthing Clamp 86010031 165 Smart Bias Tee 78210253 / ..54 / ..55 / ..56 290 78210453 / ..54 / ..55 / ..56 290 78210429 286 New or changed products RET Bias Tee 155 Kathrein’s Remote Electrical Tilt System The answer to all current and future network demands Network planning is becoming ever more complicated, especially with the advent of 3G. The challenge for wireless network operators is to balance coverage, capacity, call quality and costs in order to gain maximum revenue from their network. Each of the above factors affects the others and so network engineers use many different techniques RET However, with Kathrein’s Remote Electrical Tilt unit engineers can make the necessary adjustments without shutting down the whole system ! Further advantages of using Kathrein’s Remote Electrical Tilt (RET) system : – No need for specialized teams trained in altitude work or with special safety skills – Limited site access and/or time restrictions are not so important – No special platforms or other means of access to the antenna are required – Adjustments can be made and the relevant measurements performed speedily – Network alterations can be carried out irrespective of weather conditions – No reduction in coverage – cells remain fully operational whilst changes are being made – Operators estimate that approx. 20 % of UMTS equipment can be saved by using such a RET system. 156 for establishing the right balance they are trying to achieve. One of these methods is adjusting the antenna’s downtilt. Here, the engineer must take into consideration certain facts, such as the weather, access to the cell site, availability of specialized installation teams and special equipment etc. Moreover, such an antenna adjustment can typically take several hours to perform. Since the cell site is usually switched off for safety reasons during such an adjustment, this results in lost calls and therefore revenue whilst these changes are being made. Consequently, operators tend to make fewer adjustments and so networks are often left operating unoptimized, which also eventually results in lost revenue for the operators. Kathrein’s Remote Electrical Tilt System RET components Slimline RCU (Remote Control Unit) CCU (Central Control Unit) CCU (Central Control Unit) PCA (Portable Control Adapter) Kathrein’s overall RET system works in accordance with the AISG (Antenna Interface Standards Group) standard and 3 GPP (3rd Generation Partnership Project). DC Power and Signal Splitter Optional: Smart Bias Tee Control Cable DTMA (Double Tower Mounted Amplifier) SMB Control Cable Bias Tee Lightning Protection Device RET m syste f RET o s l i e eta For d please se brochure m e t s T sy in RE e r h t Ka Earthing Clamp 157 Remote Control Unit (RCU) Remote Control Unit (RCU) for Kathrein base station antennas with adjustable electrical downtilt and appropriate mechanical interface. ● ● Compliant to AISG 1.1 and 3GPP/AISG 2.0 Compact size ● Daisy Chain feasibility Suitable for operation under outdoor condition 86010147 Type No. Protocols Logical interface ex factory ● 86010148 compliant to AISG 1.1 and 3GPP/AISG 2.0 AISG 1.1 1) Input voltage range Power consumption Connectors 2) 3GPP/AISG 2.0 10 ... 30 V (pin 1, pin 6) < 1 W (stand by); < 10 W (motor activated) 2 x 8 pin connector according to IEC 60130-9; according to AISG Daisy chain in: male; Daisy chain out: female Hardware interfaces RS 485A/B (pin 5, pin 3); power supply (pin 1, pin 6); DC return (pin 7); according to AISG / 3GPP Adjustment time (full range) 40 sec (typically, depending on antenna type) Adjustment cycles > 50,000 Temperature range –40 °C … +60 °C Protection class IP 24 Lightning protection AISG interface (each pin) 2.5 kA (10/350 µs) 8 kA (8/20 µs) Housing material Profile: Aluminum coated; cover: Aluminum Weight 525 g (1.16 lbs) Packing size 245 x 93 x 102 mm, (9.6 x 3.6 x 4 inches) Dimensions (H x W x D) 1) 177.5 x 59.5 x 49.5 mm, (7.0 x 2.3 x 1.9 inches) The protocol of the logical interface can be switched from AISG 1.1 to 3GPP/AISG 2.0 and vice versa with a vendor specific command. Start-up operation of the RCU 86010147 is only possible in a RET system supporting AISG 1.1 and start-up operation of the RCU 86010148 is only possible in a RET system supporting 3GPP/AISG 2.0! The protocol can also be changed as follows: AISG 1.1 to 3 GPP: Enter “3GPP” into the additional data filed “Installer’s ID” and perform a layer 7 reset or a power reset. 3GPP to AISG 1.1: Daisy chain in Enter “AISG1” into the additional data field “Installer’s ID” and perform a layer 2 reset or a (male) power reset. After switching the protocol any other information can be entered into the “Installer’s ID” field Daisy chain out (female) Please note: If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the RCU must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information. 2) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector should be tightened by hand only! Standards: EN 60950-1 (Safety) EN 55022 (Emission) EN 55024 (Immunity) ETS 300019-1-4 (Environmental) UL 60950-1; 1st edition CE, FCC Scope of supply: Remote Control Unit Assembly paste RET Certification: 8 mm (0.31″) 158 28.5 mm (1.1″) 33.2 mm (1.27″) 59.5 mm (2.34″) 49.5 mm (1.95″) Ø 46 mm (Ø 1.8″) M42x1.5 173.6 mm (6.8″) Bottom view of RCU Central Control Unit (CCU) For Remote Electrical Tilt (RET) and Tower Mounted Amplifier (TMA) Control For indoor use Central Control Unit 86010006 Type No. Connectors to RCU Power supply from BTS 86010026 3 x 8 pin connector acc. to IEC 60130-9, female, acc. to AISG 1) DC: –48 V / max. 1.7 A AC: 100 … 240 V / 50 ... 60 Hz / max. 1.6 A Power supply to RCU DC: –48 V / max. 1.7 A 3 x +29 V DC / max. 1.7 A (in total) 3 x +13 V DC / max. 3.8 A (in total) Total output power Max. 50 W Interface to RCU and TMA RS 485 / power supply Protocol to RCU and TMA HDLC hex-coded command set, acc. to AISG Interface to BTS Ethernet (10 Base-T) and RS 232 Protocols to BTS TCP/IP, PPP, HTTP/HTML, UDP, DHCP, FTP, SNMP, ICMP/PING Alarm interface to BTS 8 x open collector output, user programmable Max. number of RCU’s and/or TMA’s Up to 27 RCU’s in daisy chain and up to 6 DTMA’s; depending on cable configuration and max. power Max. length of control cable 200 m (9 RCU’s in daisy chain configuration) Temperature range –25 °C ... +55 °C ambient temperature Packing size 597 mm x 367 mm x 148 mm Dimensions (h / w / d) 19" 1 HU* (43.6 mm / 483 mm / 250 mm) * HU = Height Unit 1) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand tightened’). The connector should be tightened by hand only. Standards: EN 60950-1 EN 55022 EN 55024 UL 60950-1, 1 st edition Certifications: CE, FCC part 15 class B; UL Scope of supply: CCU RET Manual DC Cable AC Power Cords for USA, UK and Germany Ethernet cable, crossed CCU Interfaces Examples of CCU – RCU connections 3 x RS 485 3 x 13 V / 3 x 29 V RET GND AC: 100 – 240 V max. 1.6 A (only 860 10006) Alarm Interface DC: –48 V max. 1.7 A Network Interfaces 8 x Open Collector Ethernet RS 232 CCU Central Control Unit 159 Central Control Unit (CCU) For Remote Electrical Tilt (RET) and Tower Mounted Amplifier (TMA) Control For indoor use Central Control Unit 86010140 Type No. Connector to RCU 86010141 8 pin connector acc. to IEC 60130-9, female, acc. to AISG 1) Power supply from BTS AC: 100 … 240 V / 50 ... 60 Hz / max. 1.6 A Power supply to RCU DC: –48 V / max. 1.7 A +29 V DC / max. 1.7 A Total output power Max. 50 W Interface to RCU and TMA RS 485 / power supply Protocol to RCU and TMA HDLC hex-coded command set, acc. to AISG Interface to BTS Ethernet (10 Base-T) and RS 232 Protocols to BTS TCP/IP, PPP, HTTP/HTML, UDP, DHCP, FTP, SNMP, ICMP/PING Alarm interface to BTS 8 x open collector output, user programmable Lightning protection No lightning protection for AISG interface2) 8/20 µs, 2.5 KA Ethernet-, DC- and Alarm Interface Max. number of RCU’s and/or TMA’s Up to 27 RCU’s in daisy chain and up to 6 DTMA’s; depending on cable configuration and max. power Max. length of control cable 200 m (9 RCU’s in daisy chain configuration) Temperature range –25 °C ... +55 °C ambient temperature Packing size 597 mm x 367 mm x 148 mm 19″ 1 HU* (43.6 mm / 483 mm / 250 mm) Dimensions (h / w / d) * HU = Height Unit 1) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand tightened’). The connector should be tightened by hand only. 2) Please note: In order to achieve lightning protection acc. to IEC 61643-1/-3 (10/350 µs), please install the Kathrein Lightning Protection Device (type no. 860 10030). For additional information about lightning protection of the CCU, we kindly refer to RET Installation Manual. Standards: EN 60950-1 EN 55022 EN 55024 UL 60950-1, 1 st edition Certifications: CE, FCC part 15 class B; UL Scope of supply: CCU RET Manual DC Cable (only 860 10141) AC Power Cords for USA, UK and Germany (only 860 10140) Ethernet cable, crossed CCU Interfaces 160 GND AC: 100 – 240 V max. 1.6 A (only 860 10140) DC: –48 V max. 1.7 A (only 860 10141) 8 x Open Collector Ethernet RS 232 RET CCU Central Control Unit Alarm Interface 860 10141 Examples of CCU – RCU connections RS 485 DC 29 V Network Interfaces 860 10140 Portable Control Adapter (PCA) For Remote Control Unit (RCU) Portable Control Adapter 86010046 Type No. Connector * to RCU/TMA 1 x 8-pin connector according to IEC 60130-9, female, conforming to AISG RF-connector (SMB male) Input voltage of PCA 24 V DC Output voltage to RCU’s/TMA’s Output power (power supply to RCU’s/TMA’s) AISG female pin 6 (24 AISG female pin 1 (12 RF male (at 24 RF male (at 12 V V V V DC): DC): DC): DC): 24 14 24 14 V V V V DC DC DC DC ±10% ±7% ±10% ±7% *** *** AISG female pin 6 (24 V DC) without load on pin 1 (12 V DC) and on RF-plug: ≤ 60 W AISG female Pin 1 (12 V DC) with max. 30 W load on pin 6 (24 V DC) and/or on RF plug: ≤ 30 W Current monitoring measuremant level Per branch (12 V, 24 V, RF): 10 – 2500 mA Over-current protection Per branch (12 V, 24 V, RF): < 2500 mA Interface to RCU/TMA RS 485 / power supply / RF connector (SMB male) Protocol to RCU/TMA HDLC hex-coded command set, conforming to AISG 1.1 and 3GPP / AISG 2.0 Interface to PC Max. number of RCU’s/TMA’s USB 1.1/2.0 27/3 pcs., depending on system configuration and length of control cable Max. length of control cable 200 m / 9 RCU’s (in daisy chain configuration) 150 m / 6 RCU’s (in splitter configuration) Weight 535 g (incl. external power adapter) Temperature range 0 ... +55 °C ambient temperature Height x width x depth 40 mm x 95 mm x 160 mm External power supply ** Input: 90 – 264 V AC, 47 – 63 Hz 24 V DC / 3.0 A * Certificate: CE FCC part 15 class B UL (for external power adapter) Standards: EN 60950-1 EN 55022 EN 55024 System requirements for PCA Software: Windows 2000; Windows XP (32 bit version) Scope of supply: PCA External power supply (24 V DC / 70 W) USB cable AC power cable CD-ROM with PCA software, drivers and manual Installation guide Transport case RET Tightening torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector should be tightened by hand only! ** If powered via AISG-interface, no external power supply is required. *** Switchable with software 161 Connecting Cable For Remote Electrical Tilt (RET) System For indoor and outdoor use RET Cable for power supply and control Type No. Connectors 86010007 … 2 x 8 pin connector according IEC 60130-9, female/male Tightening torque for fixing the connectors 0.5 – 1 Nm (The connector should be tightened by hand only) Construction Screen 1x twisted pair 100 Ω/1 MHz 2x power supply, 1x ground AWM style 20317 I/II A/B + 20549 + 20233 Rated current 4 A (power supply) (at 50 °C air temperature) Temperature range –40 °C to +80 °C, (fixed position) Protection class IP 67 (connected) Cable diameter 8 mm Flammability Colour Minimum bending radius: VL 1581 VW-1 CSA FT 1 Black, similar to RAL 9005 One time 60 mm, several times 120 mm. The male and female connectors of sll Kathrein RET products are compatible components which are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. Control Cable Type No. 0.5 m 86010054 1m 86010007 2m 86010008 3m 86010029 5m 86010009 10 m 86010010 20 m 86010032 25 m 86010011 40 m 86010012 50 m 86010033 60 m 86010013 80 m 86010014 100 m 86010015 RET Length 162 Female 7 8 Male 6 6 3 1 5 4 2 8 7 1 3 4 5 2 PIN assignment according AISG: 1 +13 V DC (+12 V DC nominal) 2 not connected 3 RS485 B 4 not connected 5 RS485 A 6 +29 V DC (+24 V DC nominal) 7 DC Return 8 not connected DC-Power and Signal Splitter For Remote Electrical Tilt (RET) Indoor and Outdoor Use AISG compliant device for splitting of DC-power and control signals from one input to three outputs. 3-way-Splitter for RET 86010002 Type No. Connectors 4 x 8 pin connector according IEC 60130-9, 1 x male, 3 x female 1) Rated current (power supply) 3 A (at 50 °C) Max. voltage 60 V Protection class IP 65 Weight 250 g Packing size 114 mm x 117 mm x 117 mm Height/width/depth 1) 91 mm / 103 mm / 72 mm The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handtightened’). The connector should be thightened by hand only! Material: Connector plate: Aluminum. Cap: Plastic. Mounting: Mast mounting (50 – 145 mm diameter) by clamp. Wall mounting by screws (not supplied). Note: Connectors must be situated at the bottom. No inverted mounting possible. Scope of supply: 3-way Splitter Clamp (Art.-No. 1311847) 2 pins (power supply, max. 3 A) 6 pins (max. 0.1 A) Output 1 Output 2 Output 3 RET Input Clamp, Art. No. 1311847 163 Lightning Protection Device (LPD) For Remote Electrical Tilt (RET) Indoor and Outdoor Use The device is designed for lightning protection of control cables carrying partial lightning currents up to 25 kA (shield) and 2.5 kA (inner conductor), according IEC 61643-1, IEC 61312-3. Each pin is protected individually. Lightning Protection Device for RET 86010030 Type No. Connectors 1) SPD-Type Max. impuls current 2 x 8 pin connector according IEC 60130-9, input: male, output: female 8 x bipolar gas tube 25 kA (housing, shield) (10/350 µs) inner conductors: 2.5 kA/pin (10/350 µs) Max. dynamic overvoltage at spark gap (1 kV/µs) < 700 V Static overvoltage (100 V/s) < 100 V Grounding Max. operation current Via mounting plate / clamps at metallic surfaces or via separate cable, min. cross-section 5 mm2 Cu (screw M6) 4 A at 50 °C Max. operation voltage 60 V Weight 250 g Packing size Height/width/depth 114 mm x 117 mm x 117 mm 91 mm / 103 mm / 72 mm The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handtightened’). The connector should be thightened by hand only! 1) Material: Connector plate: Aluminum. Cap: Plastic. Mounting: Mast mounting (50 – 145 mm diameter) by clamp. Wall mounting by screws (not supplied). Note: No decoupling elements are integrated. The coordination with additional LPD’s (device input) should be checked according to IEC 61312. Grounding of the device via the mounting plate at metallic surfaces or via additional grounding cable (not included in the delivery extend). RET Connectors must be situated at the bottom. No inverted mounting possible. Important: A control cable with a minimum length of 2 meters is required between Lightning Protection Device and Central Control Unit at the BTS to achieve the required decoupling. Scope of supply: 164 Lightning Protection Device Clamp (50 ... 145 mm) Earthing Clamp For Power Supply and Control Cable For Remote Control Unit (RCU) The clamp is designed for lightning protection of control cables according to EN 50164-1 Earthing clamp for RCU power supply and signal cable 86010031 Type No. Max. lightning current 20 kA (pulse 10/350 µsec) Contact resistance < 3 mΩ Protection class IP 68 Grounding Via stranded grounding wire, 16 mm2, length 0.5 m, one end terminated with cable eye (10 mm lug) Packing size Plastic bag: 210 mm x 210 mm Weight 160 g Material: Body: Stainless steel with vulcanized EthylenePropylene-Caoutchouc Screw: Stainless steel Skin: Copper alloy Grounding wire: Copper Please note: The earthing clamp is suitable only for the Kathrein Power Supply and Signal Cables, Type No. 860 10007 to 860 10015, 860 10029, 860 10032, 860 10033, 860 10054 to 860 10060 or shielded cables with – shield diameter 6.1 mm – jacket diameter 7.8 mm ±0.3 mm The kit contains: 1 x Grounding kit body incl. Butyl sealing rope covered with paper 1 x Screw M6 DIN 912 1 x Grounding wire Mounting instructions: RET This instruction is written for qualified and experienced personnel. Please read it carefully before starting work. Any liability or responsibility for the result of improper or unsafe installation is disclaimed! Attention ! Install grounding kit only where the cable runs straight. Fig. 1a Preassembled grounding kit. Fig. 1b Clean the plastic jacket at the desired grounding point and cut out a strip of 15 mm with aid of a suitable stripping tool. Remove covering paper from Butyl sealing. Wrap the grounding kit body around the cable and align it. Tighten the screw (> 6 Nm) 165 166 Summary – Electrical Accessories 380 ... 3800 Splitters Type Type No. 2-way Splitter 380–3800 2-way Splitter 380–3800 86010130 86010131 380 – 3800 MHz Indoor/Outdoor 380 – 3800 MHz Indoor/Outdoor 200 W 700 W N 7-16 168 168 2-way Splitter 694–2700 3-way Splitter 694–2700 4-way Splitter 694–2700 86010017 86010018 86010019 694 – 2700 MHz 694 – 2700 MHz 694 – 2700 MHz 100 W 100 W 100 W N N N 169 169 169 2-way 2-way 3-way 3-way 4-way 4-way 86010100 86010101 86010102 86010103 86010104 86010105 694 694 694 694 694 694 N 7-16 N 7-16 N 7-16 170 170 170 170 170 170 2-way Tapper 694–2700 7.0/1.0 dB 2-way Tapper 694–2700 10.4/0.4 dB 2-way Tapper 694–2700 15.1/0.1 dB 86010136 86010137 86010138 694 – 2700 MHz 694 – 2700 MHz 694 – 2700 MHz 100 W 100 W 100 W N N N 171 171 171 2-way Tapper 694–2700 7.0/1.0 dB 2-way Tapper 694–2700 10.4/0.4 dB 2-way Tapper 694–2700 15.1/0.1 dB 86010150 86010151 86010152 694 – 2700 MHz Indoor/Outdoor 694 – 2700 MHz Indoor/Outdoor 694 – 2700 MHz Indoor/Outdoor 500 W 500 W 500 W 7-16 7-16 7-16 172 172 172 Indoor 100 W N 173 Indoor 100 W N 173 Splitter Splitter Splitter Splitter Splitter Splitter 694–3800 694–3800 694–3800 694–3800 694–3800 694–3800 Frequency range – – – – – – 3800 3800 3800 3800 3800 3800 MHz MHz MHz MHz MHz MHz Remark Indoor Indoor Indoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Max. power 200 700 200 700 200 700 W W W W W W Connector Page female Tappers Indoor Indoor Indoor Continuously adjustable ratio 2-way Tapper 790–960/1710–2170 5.0–15.0dB 2-way Tapper 870–960/1710–2500 5.0–15.0dB K63236001 86010023 790 1710 870 1710 – – – – 960 2170 960 2500 MHz MHz MHz MHz New or changed product Antenna Measurement Tools (from Schomandl) SWR Instrument FAT 2710 174 WLAN Power Meter (VSWR) 175 WLAN Power Meter (Power) 175 Broadcast RF Power Monitor 176 Safe One Resonal RF Safety Monitor 177 167 Electrical Accessories Power Meter Low-loss Power Splitters Multi-band 380 –3800 For indoor and outdoor use. 2-way Splitter 380–3800 86010130 86010131 Type No. Connector (female) Max. power (at 50 °C ambient temperature) N 7-16 200 W 700 W For connecting ... antennas 2 Frequency range 380 – 3800 MHz VSWR < 1.5 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Impedance 50 Ω Insertion loss < 0.05 dB Weight 750 g Packing size 870 g 300 x 75 x 75 mm Material: Brass. Surface treatment: CuSnZn3 Mounting: Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). DC capability: DC transmission between all terminations (suitable for remote power supply systems). Environmental conditions; ETS 300 019-1-4 class 4.1 E – Low temperature: –55 °C – High temperature (dry): +60 °C IP 65 86010131 15 14.5 86010131 SW 24 7 34 86010130 35 61 input 260 86010130 36 SW 24 11 54 input 13.5 263.5 Clamps (order separately) Splitters Type No. 736801 736802 736803 736804 736805 Description 1 1 1 1 1 clamp clamp clamp clamp clamp Remarks Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 – – – – – 60 80 100 120 140 mm mm mm mm mm diameter diameter diameter diameter diameter 736805 168 Multi-band Low-loss Power Splitters 694 –2700 For indoor use. 2-way Splitter 694–2700 3-way Splitter 694–2700 4-way Splitter 694–2700 86010017 Frequency range 86010019 694 – 2700 MHz For connecting ... antennas 2 3 Insertion loss 4 < 0.05 dB Impedance VSWR 86010018 50 Ω 694 – 894 MHz: 790 – 2500 MHz: 2500 – 2700 MHz: < 1.52 < 1.25 < 2.02 Intermodulation IM3 < 1.52 < 1.25 < 2.02 < 1.5 < 1.3 < 2.0 < –150 dBc (2 x 43 dBm carrier) Max. power 100 W (at 50 °C ambient temperature) Connector N female Weight approx. 0.6 kg Profile cross-section 25 x 25 mm Packing size 242 x 110 x 95 mm Max. size 204 / 63 / 41 mm Material: Housing: Aluminum. Inner conductor: Brass. DC capability: DC transmission between all terminations (suitbale for remote power supply systems). Environmental conditions: IP 52 Input 860 10019 Splitters Type No. 169 Multi-band Low-loss Power Splitters 694 – 3800 For indoor and outdoor use. 2-way Splitter 694–3800 3-way Splitter 694–3800 4-way Splitter 694–3800 86010100 86010101 86010102 86010103 86010104 86010105 Type No. Connector (female) Max. power (at 50 °C ambient temperature) N 7-16 N 7-16 N 7-16 200 W 700 W 200 W 700 W 200 W 700 W For connecting ... antennas 2 3 Frequency range 4 694 – 3800 MHz VSWR 694 – 894 MHz: < 1.32 790 – 3800 MHz: < 1.15 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Impedance 50 Ω Insertion loss < 0.05 dB Weight 750 g 870 g 760 g Packing size 900 g 775 g 960 g 300 x 75 x 75 mm Material: Brass. Surface treatment: CuSnZn3 Mounting: Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). DC capability: DC transmission between all terminations (suitable for remote power supply systems). Environmental conditions; ETS 300 019-1-4 class 4.1 E – Low temperature: –55 °C – High temperature (dry): +60 °C IP 65 26 86010105 15 SW 24 7 34 35 61 input 64.5 260 36 25 86010104 SW 24 86010105 54 input 86010104 263.5 63 Clamps (order separately) Splitters Type No. 736801 736802 736803 736804 736805 170 Description 1 1 1 1 1 clamp clamp clamp clamp clamp Remarks Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 – – – – – 60 80 100 120 140 mm mm mm mm mm diameter diameter diameter diameter diameter 736805 Multi-band Low-loss Power Tappers 694 –2700 For indoor use P1 2-way Tapper 694–2700 7.0 /1.0dB 2-way Tapper 694–2700 10.4/0.4dB 2-way Tapper 694–2700 15.1/0.1dB 86010136 Frequency range 86010137 86010138 P2 694 – 2700 MHz Tap Loss Input ↔ P1 Input ↔ P2 – 1.0 dB – 7.0 dB – 0.4 dB – 10.4 dB For connecting ... antennas – 0.1 dB – 15.1 dB 2 Insertion loss < 0.05 dB Impedance 50 Ω VSWR 694 – 790 MHz: < 2.0 790 – 2500 MHz: < 1.5 2500 – 2700 MHz: < 2.0 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power 100 W (at 50 °C ambient temperature) Connector N female Weight 500 g Profile cross-section 25 x 25 mm Packing size 267 x 95 x 111 mm Max. size 244 / 64 / 25 mm Material: Housing: Aluminum. Inner conductor: Brass. DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Environmental conditions: IP 52 Input 860 10138 Tappers Type No. 171 Multi-band Low-loss Power Tappers 694 –2700 For indoor and outdoor use. 2-way Tapper 694–2700 7.0 /1.0dB 2-way Tapper 694–2700 10.4/0.4dB 2-way Tapper 694–2700 15.1/0.1dB 86010150 Type No. Frequency range 86010151 P1 86010152 694 – 2700 MHz Tap Loss Input ↔ P1 Input ↔ P2 – 1.0 dB – 7.0 dB – 0.4 dB – 10.4 dB For connecting ... antennas – 0.1 dB – 15.1 dB 2 Insertion loss P2 < 0.05 dB Impedance 50 Ω VSWR 694 – 790 MHz: < 2.0 790 – 2500 MHz: < 1.5 2500 – 2700 MHz: < 2.0 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power 500 W (at 50 °C ambient temperature) Connector 7-16 female Weight Approx. 1.3 kg Packing size 310 x 93 x 112 mm Max. size 244 / 90 / 55 mm Material: Housing: Aluminum. Inner conductor: Brass. Input DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Mounting: Bracked for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). Environmental conditions: IP 65 86010150 Clamps (order separately) Tappers Type No. Description Remarks 734360 1 tension band Mast: 34 – 60 mm diameter 734361 1 tension band Mast: 60 – 80 mm diameter 734362 1 tension band Mast: 80 – 100 mm diameter 734363 1 tension band Mast: 100 – 120 mm diameter 734364 1 tension band Mast: 120 – 140 mm diameter 734365 1 tension band Mast: 45 –125 mm diameter 172 734364 Multi-band Low-loss Power Tapper Continuously Adjustable 790 – 960 / 1710 –2170 5.0 – 15.0 dB For indoor use. P1 K63236001: 2-way Tapper 790–960/1710–2170 5.0–15.0dB 86010023: 2-way Tapper 870–960/1710–2500 5.0–15.0dB Type No. K63236001 86010023 Frequency range 790 – 960 MHz and 1710 – 2170 MHz 870 – 960 MHz and 1710 – 2500 MHz Power ratio between outputs (P2 – P1) P2 –5.0 dB to –15.0 dB continuously adjustable For connecting ... antennas 2 Insertion loss < 0.1 dB Impedance Blocking unit 50 Ω VSWR 790 – 824 MHz: < 2.1 824 – 960 MHz: < 1.7 1710 – 2170 MHz: < 1.7 Intermodulation IM3 < 1.7 < –150 dBc (2 x 43 dBm carrier) Max. power 100 W (at 50 °C ambient temperature) Connector N female Weight 0.5 kg Profile cross-section 25 x 25 mm Packing size 249 x 111 x 40 mm 277 x 111 x 40 mm Max. size 235 / 100 / 25 mm 263 / 100 / 25 mm Material: Housing: Aluminum. Inner conductor: Brass. Adjustment mechanism: ASA. DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Environmental conditions: IP 52 Input 86010023 Splitting table Splitting ratio P1 / P2 –5 –6 –7 –8 –9 – 10 – 11 – 12 – 13 – 14 – 15 3.2 4 5 6.3 8 10 12.6 15.8 20 25.1 31.6 Splitting attenuation PInput – P1 [dB] PInput – P2 [dB] – 1.2 – 1.0 – 0.8 – 0.6 – 0.5 – 0.4 – 0.3 – 0.3 – 0.2 – 0.2 – 0.1 – 6.2 – 7.0 – 7.8 – 8.6 – 9.5 – 10.4 – 11.3 – 12.3 – 13.2 – 14.2 – 15.1 Tappers P2 / P1 [dB] 173 SWR Instrument FAT 2710 • LCD Display works in direct sunlight and with backlight in dark areas. • Built-in synthesized RF sweeping source. • Measured results can stored for further analysing and documentation on internal and external storage media • Time stamp and operator ID is possible • All in one analysing for antenna tuning and control • FAT 2710 measures antenna, frequency, SWR and bandwidth by sweeping band of interest • A cost-effective SWR Analyzer covering all major Cellular and mobile radio communication bands • FAT 2710 gives you quick and reliable trouble-shooting Specifications Model Application Measurement of SWR in 50 ø transmission lines Frequency range 30->2700 MHz entered as centre and span Center Frequency 30 to 2700 MHz. Span 0 to 2670 MHz. Frequency stability Measurement range Impedance Generator output ±50ppm 1.0<SWR<9.9, 0<dB<-30dB Nom. 50 ø Approx. -4dBm Max. input on test terminal 100 mW Tolerance on SWR reading 30-650MHz)± 5%; 650-1450MHz ± 10%; and 1450-2700MHz ±15% Operating temperature range Storage temperature range Connectors Power supply Auto Power off NOT OK Normal operating use 0° C-> + 50° C -30°C -> + 50° C “N”-female RF test connector. USB A type for memory key. USB B type for serial PC communication. Mini DIN for RS232 communication up to 38400 Baud 4 NiMH type AA rechargeable batteries (Batteries, NiMH rechargeable and 230VAC/7.5VDC charger supplied) For battery economy, FAT 2710 automatically turns off 3 min. after last entry Fully charged: More than 10 hours. Colour Silver/blue Width 82 mm Depth 31 mm Height 165 mm Weight 500 gram (incl. Batteries) EMC Measurement Tools FAT 2710 (BN: 86817.001) Complies with directive 89/336EEC as amended by 92/31EEC and 93/68/EEC Standards Emissions: EN 61000-6-4: 2001 Immunity: EN 61000-6-2: 2005 Accessory Soft carrying bag with RF-adapter set, car charching cable and two 7/16 connectors Order Number for Accessory: BN: 86817.101 Please contact for technical information and orders: SCHOMANDL-Vertriebs-GmbH Bahnhofstraße 108 · D-83224 Grassau/Germany Telephone: 08641-403-140 · Telefax: 08641-403-264 e-mail: [email protected] · Internet: http://www.schomandl.de 174 WLAN Power Meter Display forward, reflected power and VSWR 2 GHz to 6 GHz Diagnose 802.11a,b and g WLAN Accessory: Soft carrying bag with SMA 50 Ohm load 6 GHz, RPSMA male BN 86817.104 to SMA female Adaptor, SMA male to RPSMA, SMA male to SMA male Adaptor and special 2,4 GHz SMA Antenna Specifications Model No.: 86817.004 Frequency range: 2 – 6 GHz Insertion loss: <0.4dB Absolute accuracy : ±1dB Power range indicated: 1µW – 999mW VSWR indicated: 1.01 – 9.99 : 1 Directivity: >30dB Peak Detect of: <1mS pulse Auto Power off 1 minute Power Supply: 3Volt (2 X AAA Alkaline) Max power consumption: 50 mA Operating time (no backlight) 20 Hours Optional Accessories: SMA to RPSMA adaptors Belt clip Option EMI/RFI EN55022 /B – Width: – Depth: – Height: Weight incl. Batteries: 58 mm 23 mm 105 mm approx. 130g Temperature: – Operating – Storage 0 to 40°C –20 to 80°C Colour: – Standard White/Grey Measurement Tools Dimensions: Please contact for technical information and orders: SCHOMANDL-Vertriebs-GmbH Bahnhofstraße 108 · D-83224 Grassau/Germany Telephone: 08641-403-140 · Telefax: 08641-403-264 e-mail: [email protected] · Internet: http://www.schomandl.de 175 Broadcast RF Power Monitor Digital RF Power Meter Also avalible as 19″ Rack mount Version: 1U Rack mount Power Monitor including all options BN 86818.000 additional power, reflected power, VSWR calculation Accessory: UHF Probe 1 or 2 required BN 86818.101 VHF Probe 1 or 2 required BN 86818.102 Specifications for Broadcast Power Monitor with external coupler Model No.: 86818.002 Frequency range: (Coupler dependent) Coupling Flatness , from 6dB/octave Probes 3015,3016 Absolute accuracy after offset adjustment: True RMS Power range: ±0,2dB ±0,2dB (±4%) –34 dBm to +10 dBm Peak Power range: +24 dBm Dynamic range: > 50 dB Power readout: Auto range 1KW – 999KW 1024 steps Coupler attenuation VHF @ 100MHz: 43 dB to 73 dB Coupler attenuation UHF @ 500MHz: 50 dB to 80 dB VSWR readout: 1,00:1-9,99:1 Remote Temperature Sensing 0 – 99°C Remote Voltage Sensing 0–100VDC Remote Current Sensing 0–3V DC (1024 bits) Relay Out/Digital Out: Open Collector 50V/0,5A Controller out for SNMP or dialup RS232 1200- 9600 Bps Power Supply: – AC power: Max power consumption: – AC 90-264V @ 50-60Hz 10V/A EMI/RFI EN55022 /B Connectors: – RF sensors – Power AC in rear Options: – Analogue/digital – RS232 DB9 Female IEC DB9 Female DB9 Male Dimensions: – Width: 19″ unit – Depth: 1HU Dimensions: – Width: Stand alone unit – Depth: – Height: Weight: Measurement Tools 50 – 860 MHz Temperature: – Operating -Storage Colour: – standard 482.5 mm 180 mm 44 mm 216 mm 180 mm 53 mm approx. 1.8 kg 5 to 50°C 20 to 80°C Silver Anodised Please contact for technical information and orders: SCHOMANDL-Vertriebs-GmbH Bahnhofstraße 108 · D-83224 Grassau/Germany Telephone: 08641-403-140 · Telefax: 08641-403-264 e-mail: [email protected] · Internet: http://www.schomandl.de 176 Safe One Personal RF Safety Monitor Monitors RF fields Indicates RF pollution Alarm and Silent modes Broadband coverage General Safety According to WHO ICNIRP Alarm 2W/m2 or 10W/m2 Specifications for Safe One Personal Safety Monitor Model No.: 86817.003 Frequency range: 10 – 10000 MHz Frequency response ICNIRP Absolute accuracy 400–2500MHz: ±6dB Power range indicated: 0. 1 – 100 W/m2 Field strenght indicated: 19 – 137 V/m Dynamic range: >30dB Audio Alarm 80dBa LED Alarm always enabled 15mcd Normal Mode Audio and LED Alarm: ( – ) Timed Mode Silent in: (– – ) 2W/m – 28V/m or 10W/m2 – 137V/m 2 5 minutes Audible Alarm Off Mode: (– – – ) Never Power Supply: 3Volt (2 X AAA Alkaline) Max power consumption no alarm: 110µA Operating time (no Audio Alarm) +500 Days Belt clip included EMI/RFI – Width: – Depth: 23 mm – Height: 105 mm Weight incl. Batteries: Temperature: Colour: 58 mm approx. 88g – Operating –10 to 40°C – Storage –20 to 80°C – Standard Black/Grey Measurement Tools Dimensions: EN55022 /B Please contact for technical information and orders: SCHOMANDL-Vertriebs-GmbH Bahnhofstraße 108 · D-83224 Grassau/Germany Telephone: 08641-403-140 · Telefax: 08641-403-264 e-mail: [email protected] · Internet: http://www.schomandl.de 177 178 Summary – Mechanical Accessories Clamps, Downtilt Kits ... Page Mounting Configurations 180 Dimensions of Panels 181 Modified Product Line of Mounting Parts 186 Amount of needed Clamps per Panel Type 187 Clamps 188 Downtilt kit “L” 189 Downtilt kit “L” and “M” 190 Downtilt kit “H” 191 Azimuth Adjustment Kits 192 3 Sector Clamps 193 Offset 194 2x Panel Mounting Kit 195 Tension Band 197 Side-mounting Clamp Omnis 198 Azimuth Adjustment Tool 201 Installation Tool Triple-band Antennas 202 179 Mechanical Accessories The hereinafter referred to “wind load category L - M - H” correspond to the defined “category of mounting hardware” given in the respective data sheets. Mounting Configurations Small Pipe Diameter Off-set Mechanical Accessories Large Pipe Diameter Flat Surface Standard Downtilt Off-set Downtilt Azimuth 180 Panels XPol 800/900 30° Half-power Beam Width Antenna Dimensions 72±0.3 0 9–0.5 XPol Panels 800/900 with 30° Half-power Beam Width 64±0.3 width 560 mm A B C 1296 mm 1358 mm 1396 mm Side view 160 123.3 Front view B C A A Corresponds with the antenna height mentioned in the technical data. 348 560 XPol Panels 800/900 with 30° Half-power Beam Width 9 Bottom view 72 64 width 576 mm A B C 2254 mm 2284 mm 2326 mm A Corresponds with the antenna height mentioned in the technical data. A B C Adjustment mechanism with integrated scale Front view 60 99 110 140 576 181 Mechanical Accessories Bottom view Panels VPol / XPol / XXPol 800/900 60°/65°/88°/90° Half-power Beam Width Antenna Dimensions 72 64 9 VPol Panel 800/900 width 258 mm A B C 264 mm 1294 mm 1934 mm 2574 mm –– 1350 mm 1990 mm 2630 mm –– 1390 mm 2030 mm 2670 mm A Corresponds with the antenna height mentioned in the technical data. 103 XPol Panel 800/900 A B C B C width 258 mm A B C 258 1294 mm 1934 mm 2254 mm 2574 mm 1340 mm 1980 mm 2300 mm 2604 mm 1382 mm 2022 mm 2342 mm 2674 mm Top view A Corresponds with the antenna height mentioned in the technical data. Rear view 72 9 64 XPol Panel 800/900 XXPol Panel 900/1800 with 65° and 90° Half-power Beam Width 58 +45° -45° A B C 256 mm 310 mm 350 mm 656 mm 710 mm 750 mm 1936 mm 1990 mm 2030 mm A B 116 width 262 mm C 262 Bottom view A Corresponds with the antenna height mentioned in the technical data. 72 Front view 9 64 XXPol Panel 800/900 with 60°, 65° and 88° Half-power Beam Width 50 width 374 mm A B C D 2024 mm 1490 mm 221 mm 617 mm 2631 mm 2020 mm 301 mm 921 mm Mechanical Accessories A Corresponds with the antenna height mentioned in the technical data. 182 A 300 Bottom view Panels Dual-band / Triple-band Antenna Dimensions 72 Dual-band XXPol 800/900 / 1800/2000 with 65° Half-power Beam Width A B C 270 mm 322 mm 362 mm 579 mm 630 mm 670 mm 9 64 770 mm 1316 mm 1916 mm 2038 mm 2516 mm 2580 mm 824 mm 1367 mm 1967 mm 2089mm 2567 mm 2634 mm 864 mm 1407 mm 2007 mm 2129 mm 2607 mm 2674 mm A Corresponds with the antenna height mentioned in the technical data. A B C 52 139 58 262 Bottom view Adjustment mechanism with integrated scale 9 72 64 1384 mm 1917 mm 2635 mm 1427 mm 1960 mm 2677 mm 1467 mm 2000 mm 2717 mm A B C 103 180 203 262 A Corresponds with the antenna height mentioned in the technical data. 45 A B C 106 149 171 Dual-band XXPol Panel 800/900 / 1800/2000 with 90° Half-power Beam Width Bottom view 72 64 9 Adjustment mechanism with integrated scale Triple-band XXXPol Panel 800/900 – 1800 – 2000 with 65° Half-power Beam Width A B C A 1498 mm 1540 mm 1932 mm 1997 mm 2058 mm 2593 mm 2628 mm 2694 mm B 1541 mm 1583 mm 1967 mm 2027 mm 2101 mm 2627 mm 2671 mm 2737 mm C 1581 mm 1623 mm 2005 mm 2067 mm 2141 mm 2667 mm 2711 mm 2777 mm 149 A Corresponds with the antenna height mentioned in the technical data. Adjustment mechanism with integrated scale 183 Mechanical Accessories 262 Bottom view Panels 1800 – 2700 MHz with 33° / 45° / 65° / 88° Half-power Beam Width Antenna Dimensions Dimensions [mm] (‘A’ corresponds to the antenna height given on the data sheet) 33° – 45° Half-power Beam Width 65° – 88 °Half-power Beam Width A B C A B C 1032 1304 1306 1942 1946 1109 1381 1412 1996 2052 1149 1421 1442 2036 2082 155 342 662 735 851 1142 1302 1314 1387 1400 1407 1902 1942 1954 1984 2160 2172 2548 209 396 716 789 896 1186 1356 1356 1429 1454 1449 1956 1996 1996 2038 2214 2246 2605 239 426 746 819 926 1216 1386 1386 1459 1484 1480 1986 2026 2026 2068 2244 2276 2635 Width according to data sheet information Front view Front view A B C A B C ø 8.5 Mechanical Accessories 9 35 64 72 184 64 Panels 1800 – 2700 MHz Detailed Connector Position Antenna Dimensions +45°/–45° Polarization 58 90° Half-power Beam Width 155 54 65° and 90° Half-power Beam Width adjustable electrical downtilt 164 45° Half-power Beam Width Multi-band adjustable electrical downtilt 199 45 30° Half-power Beam Width Multi-band adjustable electrical downtilt 299 45 65° Half-power Beam Width 2-Multi-band adjustable electrical downtilt 299 48 65° Half-power Beam Width 2-Multi-band adjustable electrical downtilt 323 57 65° Half-power Beam Width Dual-Beam adjustable electrical downtilt 380 185 Mechanical Accessories 150 50 135 0 12 Modified Product Line of Mounting Parts Type Clamp Pole Diameter in mm Type No. light / medium ∅ 28 – 64 731651 light / medium / heavy ∅ 28 – 115 738546 ∅ 110 – 220 85010002 ∅ 210 – 380 85010003 Windload Classification light / medium / heavy Downtilt kit Remark Modified product 732317 732318 light 732321 732322 Modified product Available: 2nd half 2011 732327 Downtilt kit 737971 737972 737973 light / medium 737974 737975 Modified product Available: 2nd half 2011 737977 737978 Downtilt kit heavy New product 85010008 Replacement for 85010007 Available: 2nd half 2011 Azimuth Adjustment Kit light / medium Azimuth Adjustment Kit heavy 85010015 light / medium 85010016 heavy 85010017 3 Sector Clamp light / medium ∅ 88.9 742263 ∅ 88.9 742317 ∅ 114.3 742033 ∅ 139.7 742034 Pole mounting adjustment angle ±30° (additional clamp needed) Wall mounting adjustment angle ±30° New product ∅ 114.3 85010058 New product ∅ 1397 85010059 New product light / medium New product 85010060 heavy New product 85010061 Clearance between pole and antenna (additional clamp needed) heavy Offset 85010014 2x Panel Mounting Kit light / medium 742113 Additional clamp needed heavy Tension Band Mechanical Accessories light 186 85010006 ∅ 34 – 60 734360 ∅ 60 – 80 734361 ∅ 80 – 100 734362 ∅ 100 – 120 734363 ∅ 120 – 140 734364 ∅ 45 – 125 734365 Please note: Only usable without downtilt kit Mounting Hardware Amount of needed clamps 2 pcs VPol 800/900 Antenna height: 264 mm 1 pc 187 Mechanical Accessories VPol 800/900 All other Panels Panel Accessories Mounting Hardware Clamps Clamps 731651 738546 85010002 85010003 Suitable for mast diameter 28 – 60 mm 42 – 115 mm 110 – 220 mm 210 – 380 mm Antenna – mast distance F 40 – 44 mm 37 – 44 mm 47 – 56 mm 48 – 69 mm 1 clamp 1 clamp 1 clamp 1 clamp Type No. Number of pieces Material – Clamp – Screws Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel/ Hot-dip galvanized steel/ Hot-dip galvanized steel/ Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Steinless stell – Nuts Weight 0.8 kg 1.1 kg 2.7 kg 4.8 kg Torque MA = G Torque: M8 => MA = 20 Nm M6 => MA = 8 Nm Type No. A B C D E 731651 116 mm 40 mm 40 mm 28 – 60 mm 93 mm 40 – 44 mm 20 Nm 84 mm 738546 152 mm 40 mm 40 mm 42 –115 mm 93 mm 37 – 44 mm 25 Nm 125 mm 85010002 280 mm 100 mm 50 mm 110 –220 mm 93 mm 47 – 56 mm 35 Nm 240 mm 85010003 442 mm 150 mm 50 mm 210 –380 mm 150 mm 48 – 69 mm 35 Nm 392 mm Mechanical Accessories Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. 188 F G H Standard Downtilt kit for Panel Antennas (Wind load Category “L”) Antenna height: 502 662 982 1302 – duct d pro : e i f i d Mo ble Availa 2011 f l a 2nd h mm mm mm mm 20 Nm / M8 20 Nm / M8 20 Nm / M8 Scale Before the adjustment, all joint screws must be loosened. After the adjustment has been completed, all loosened screws must be tightened. Recommended torque for M8 bolted connections: 20 Nm. Mounting accessories included. 20 Nm / M8 For heights not mentioned in this table please use downtilt kit 732327. Downtilt kit with scale Downtilt angle Antenna height Downtilt angle Type No. 502 mm 0° – 25° 732322 662 mm 0° – 19° 732321 982 mm 0° – 13° 732318 1302 mm 0° – 10° 732317 Downtilt kit without scale* Type No. Weight Material All parts: 732327 Approx. Hot-dip galanized steel 1.3 kg Nuts / washers: Stainless steel * Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna. 189 Mechanical Accessories Mounting a downtilt kit enlarges the spacing between mast and antenna by 42 mm. Standard Downtilt kit for Panel Antennas Wind load Category “L” and “M” Antenna height: 654 974 1294 1934 2254 2574 – 735 mm – 1032 mm – 1306 mm – 1946 mm / 2256 mm – 2582 mm – duct d pro : e i f i d Mo ble Availa 2011 f l a 2nd h 20 Nm / M8 20 Nm / M8 50 Nm / M12 Scale Before the adjustment, all joint screws must be loosened. After the adjustment has been completed, all loosened screws must be tightened. Recommended torque for M8 bolted connections: 20 Nm. Mounting accessories included. 20 Nm / M8 For heights not mentioned in this table please use downtilt kit 737978. Downtilt kit with scale Downtilt angle Antenna height Downtilt angle Type No. 654 – 735 mm 0° – 30° 737972 974 – 1032 mm 0° – 21° 737973 1294 –1306 mm 0° – 16° 737974 1934 – 1946 mm 0° – 11° 737975 2254 / 2256 mm 0° – 9° 737977 2574 – 2582 mm 0° – 8° 737971 Downtilt kit without scale* Type No. Weight Material All parts: 737978 Approx. Hot-dip galanized steel 2.3 kg Nuts / washers: Stainless steel * Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna. Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm. Mechanical Accessories Use the downtilt kit together with the clamps Type No. 731651, 738546, 85010002, 85010003, 85010014 for pole mounting and 85010016 for wall mounting. 190 Standard Downtilt kit for Panel Antennas (Wind load Category “H”) t– roduc p w e N ble: Availa 2011 l af 2nd h Special downtilt kit for Panel antennas with a higher wind load. Mounting accessories included M10 Downtilt kit 85010008 Type No. Preferred range of use – Panel antennas with a higher wind load – Panel antennas with attached mounting plates – Downtilt kit without scale for universal use Weight M8 M12 6.5 kg Material Hot-dip galvanized steel Screws Hot-dip galvanized steel / stainless steel All nuts Stainless steel M10 Recommended mast clamps: Mast diameter Weight approx. Units per antenna 42 – 115 mm 1.1 kg 2 1 clamp 110 – 220 mm 2.9 kg 2 1 clamp 210 – 380 mm 4.8 kg 2 Type No. Description 738546 1 clamp 85010002 85010003 Torque M8 20 Nm M10 50 Nm M12 90 Nm Ø9 –0.5 Screw size 72±0.3 Ø9 –0.5 Recommended torque for all bolted connections: 72±0.3 96 < 5000 N Lateral wind load < 1300 N 310 Frontal wind load 62 Maximum acceptable load: Downtilt angle Downtilt angle 1498 mm 0° – 13° 2058 mm 0° – 10° 2516 mm 0° – 8° 2628 mm 0° – 8° 155 M10 191 Mechanical Accessories Antenna height All Panels Mounting Hardware Azimuth Adjustment Kits Pole mounting Wall mounting Detail Y X 358 308±1 109 MA 46 86 50 104 62±0.5 Distance B see table 43 ∅ 15 ±0.5 14 106 180±1 The azimuth adjustment kit for pole mounting can be mounted with all suitable clamps, 3-Sector clamps and 2x A-/C-/F-Panel mounting kits (with the latter only as an interface between mounting kit and antenna). Type No. 85010014 Suitable for Number of pieces Distance between screws [B] 2 brackets 64 mm Angular range Weight / kit 85010015 approx. 1260 g 2 brackets 2 brackets 72 mm 64 mm approx. 1260 g Mechanical Accessories 72 mm approx. 2500 g approx. 2500 g Screws and dowels for wall fastening are not supplied, they must be chosen by installer according to on-site requirements. Adapter for downtilt kit 732 3xx serie Adapter for downtilt kit 732 3xx serie Parts are hot-dip galvanized steel; Captive nuts are stainless steel 2150 N 760 N 5100 N 1350 N 2150 N 760 N Recommended torque: Screws M6: 8 Nm; Screws M8: 20 Nm; MoS2 greased. Minimum torque MA: 30 Nm; MoS2 greased 192 2 brackets ± 30° all screws Materials 85010017 wall mounting ± 30° Supplied mounting accessories Max. permissible static load / kit – X direction – Y direction 85010016 pole mounting 5100 N 1350 N 3 Sector Panel Arrangement 3 Sector Clamp Kit Mounting Hardware ● Slim and unobstrusive design. Nearly cylindrical optical appearance with small outer diameter. ● Suitable for all Panels with an antenna housing width less than 400 mm (Hmax). Please note: Panels with connector position “Rearside, pointing downwards” fit only with downtilt kit or offset mounted in-between. ● M8 E F B 60 ° 3 sector clamp C G A Mounting support clamp Torque 25 Nm E 64 64 64 64 72 72 F 50 50 49 49 50 50 G 45 45 45 45 45 45 Hmax 280 361 375 400 375 400 Weight 4 kg 4 kg 4 kg 4 kg 4 kg 4 kg ax Type No. A B C D 742263 88.9 65 180 168 742317 88.9 88 213 199 742033 114.3 88 217 207 742034 139.7 100 236 228 85010058 114.3 88 217 207 85010059 139.7 100 236 228 All dimensions in mm. Dout is determined by mounted components. t D ou Hm D Bottom view without downtilt kit 3 Sector Clamp Kit (Antenna Wind load Category “L” and “M”) Type No. Angle between antennas Suitable for mast diameter Number of pieces Material – 3 sector clamp – Mounting support clamp – Screws – Nuts 742263 742317 742033 742034 120° 120° 120° 120° 88.9 mm 88.9 mm 114.3 mm 139.7 mm 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x mounting support clamp 2 x mounting support clamp 2 x mounting support clamp 2 x mounting support clamp Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Aluminum Aluminum Aluminum Aluminum Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Stainless steel Stainless steel Stainless steel Stainless steel Type No. Angle between antennas Suitable for mast diameter Number of pieces Material – 3 sector clamp – Mounting support clamp – Screws – Nuts 85010058 85010059 120° 114.3 mm 2 x 3 sector clamp 2 x mounting support clamp 120° 139.7 mm 2 x 3 sector clamp 2 x mounting support clamp Hot-dip galvanized steel Aluminum Hot-dip galvanized steel Stainless steel Hot-dip galvanized steel Aluminum Hot-dip galvanized steel Stainless steel 193 Mechanical Accessories 3 Sector Clamp Kit (Antenna Wind load Category “H”) Mounting Hardware Offset for Panel Antennas Type No. Wind load category 85010060 85010061 “L” and “M” “H” No. of pieces 2x spacer Material: – spacer – nuts Dimension “A” Hot-dip galvanized steel Stainless steel 64 mm Weight 72 mm 1.3 kg Fitting accessories Supplied Recommended torque for M8 bolted connections: 20 Nm Please use the offset in combination with clamps corresponding to the pole diameter. 42 77 104 A Mounting accessories (order separately) Possible clamps in combination with: 85010060 Mast diameter Weight approx. Units per antenna 1 clamp 28 – 64 mm 0.8 kg 2 1 clamp 42 – 115 mm 1.1 kg 2 1 clamp 110 – 220 mm 2.9 kg 2 1 clamp 210 – 380 mm 4.8 kg 2 Type No. Description Mast diameter Weight approx. Units per antenna 738546 1 clamp 42 – 115 mm 1.1 kg 2 85010002 1 clamp 110 – 220 mm 2.9 kg 2 85010003 1 clamp 210 – 380 mm 4.8 kg 2 Type No. Description 731651 738546 85010002 85010003 85010061 Mechanical Accessories If a downtilt kit is used, please choose the fitting one from the antenna data sheet. 194 90 Panel Accessories 2 x Panel Mounting Kit for Panels width 112 mm and 155 mm Use this mounting kit only for Panels with a maximum width of 160 mm. Wind load category: L (Light) or M (Medium) 2 x Panel Mounting Kit 742113 Type No. Contens Material: – Clamp and screws – Nuts and washers Weight 2 x brackets and mounting accessories Hot-dip galvanized steel Stainless steel Approx. 1.6 kg Recommended torque for M8 bolted connections: 20 Nm 90 72±0.3 10 9 118 75 30° 19 64±0.3 38 Ø 9 64±0.3 64±0.3 82.5 82.5 270 Configuration with mechanical downtilt Use the 2 x Panel Mounting Kit together with the following mounting accessories Type No. Description 731651 738546 85010002 85010003 85010060 737978 1 1 1 1 1 1 clamp clamp clamp clamp offset downtilt kit Remarks Mast: 28 – 60 mm diameter Mast: 42 – 115 mm diameter Mast: 110 – 220 mm diameter Mast: 210 – 380 mm diameter in combination with the clamps Downtilt angle: depending on antenna height Weight Units per approx. antenna 0.8 1.1 2.7 4.8 1.3 2.3 kg kg kg kg kg kg 2 2 2 2 2 1 For a three sector panel arrangement, use the mounting kit type no. 742113 together with the three sector clamp 742213, 742033 or 742034. Three sector clamp 742263 does not match. If a downtilt kit is used, please choose the fitting one from the antenna datasheet. 195 Mechanical Accessories Configuration without mechanical downtilt Panels VPol / XPol 800/900 Panels XXPol 800/900 / 1800/2000 2 x Panel Mounting Kit Use this mounting kit only for Panels with a maximum width of 262 mm. Wind load category: H (Heavy) Type No. 85010006 Contens 2 x brackets and mounting accessories Material: – Clamp and screws – Nuts and washers Hot-dip galvanized steel Stainless steel Weight Approx. 3.3 kg Recommended torque for M8 bolted connections: 20 Nm 72±0.3 64±0.3 64±0.3 73 48 90–0.5 64±0.3 280 390 Configuration without mechanical downtilt Configuration with mechanical downtilt Mounting Accessories (order separately) Clamps (only the listed clamps are allowed!) Weight Units per approx. antenna Type No. Description Remarks 85010002 1 clamp Mast: 110 – 220 mm diameter 2.7 kg 2 85010003 1 clamp Mast: 210 – 380 mm diameter 4.8 kg 2 85010061 1 offset in combination with the clamps 1.3 kg 2 Mechanical Accessories If a downtilt kit is used, please choose the fitting one from the antenna datasheet. 196 Mounting Hardware Tension Band for Panel Antennas (Wind load Category “L”) Suitable for mast diameter Material Weight (approx.) 734360 734361 734362 734363 734364 734365 34 – 60 mm 60 – 80 mm 80 – 100 mm 100 – 120 mm 120 – 140 mm 45 – 125 mm Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel 0.06 kg 0.07 kg 0.08 kg 0.09 kg 0.11 kg 0.08 kg e: e not wntilt kit ! s a e l P t do ithou w e l usab Only 197 Mechanical Accessories Type No. Side-mounting Clamp Omnidirectional Antennas Large Pipe Type No. 738908 For mast diameters of 94 – 125 mm Antenna Mast b a b Mechanical Accessories a 198 Side-mounting Bracket Omnidirectional Antennas Type No. 737398 ∅D Side-mounting bracket (for mast diameters of 40 – 105 mm) Type No. 737398 Bracket At the top and at the bottom Fits for antenna type no: 800/900 MHz 736347 736348 736349 736350 736351 738664 738192 1800 MHz 739785 738187 739404 737190 A UMTS 741790 Dual-band 80010274 Side-mounting is possible for four fixed distances between the tubular mast and the antenna: 800/900 MHz A = 100 mm = 0.3 λ 1800/2000 MHz (holes 1 and 3) A = 160 mm = 0.5 λ A = 240 mm = 0.75 λ A = 80 mm = 0.5 λ A A A A (hole 2) Bracket Antenna Antenna base Mast Bracket Hole 3 D Pipe D Hole 1 D Horizontal Radiation Pattern Spacing A Curve Hole 3 Hole 2 D Pipe D D Horizontal Radiation Pattern 100 mm Spacing A Curve Pipe D Curve Horizontal Radiation Pattern Spacing A 100 mm 40 mm dB 3 3 0 0 direction from mast to antenna 80 mm 160 mm 240 mm direction from mast to antenna 3 100 mm 240 mm 0 direction from mast to antenna 199 Mechanical Accessories 100 mm dB 160 mm dB 40 mm Side-mounting Brackets Omnidirectional Antennas 900 For mast diameters of 40 – 105 mm Type No. Bracket K61335 at the bottom only Fits for antenna type no. øD K75116 .. K75156 . Side mounting is possible for three fixed distances between the tubular mast and the antenna: 100 mm = 0.3 λ 160 mm = 0.5 λ 240 mm = 0.75 λ Pipe D Horizontal Radiation Pattern Spacing A Curve Additional gain to the nominal value of the antenna gain A 100 mm 2 dB 160 mm 3 dB dB 40 mm 3 240 mm 2 dB 0 direction from mast to antenna 100 mm 2.5 dB 160 mm 3.5 dB dB 100 mm 3 240 mm 0 Mechanical Accessories direction from mast to antenna 200 2.5 dB K61335 All Panels Accessories Azimuth Adjustment Tool Type No. 738440 Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth adjustment tool. This tool is suitable to all types of Panels and Tri-Sector Pipe Antennas with a maximum width of 315 mm. Elevation compensation Target object Target object Scale Move the stopper to central position* Panel Clamping device Instruction: – Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). – Set this angle on the scale of the adjustment tool. – Place the adjustment tool onto the antenna and tighten the clamping device. – Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool. 201 Mechanical Accessories – Use the telescope to aim at the target object, if necessary, use elevation compensation. Kathrein Installation Tool for Triple-band Antennas Type No. 85010005 Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool (as shown below) in combination with a standard torque-wrench. Kathrein installation set: Type No. 85010005 Set has to be ordered separately! Set consists of two spanners of 27 and 32 mm width. 1/2″ square actuation according to DIN 3120 Form C 27 or 32 mm These tools are suitable for 7-16 connectors with a wrench size of 27 mm or 32 mm. Tighten nut within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifications. Description of connector arrangement: 2 1 8 Adjustment mechanisms (1 – 3) 3 6 4 5 7 9 Feederline connectors (4 – 9) There are six feederline connectors and three adjustment mechanisms located at the bottom of the antenna. Mechanical Accessories For detailed information about feederline installation for Triple-band Antennas please see Kathrein RET system brochure. 202 Filters / Duplexers Multiband Combiners Dual-Band Combiners Triple-Band Combiners Quad-Band Combiners Same-Band Combiners Hybrid Combiners Same-Band Combiner Duplex Hybrid Combiner Active Duplex Hybrid Combiner Hybrid Combiner 2 : 1 Hybrid Combiner 4 : 4 3-dB Couplers Hybrid Ring Junctions System Components Bias Tees Measuring Directional Couplers DC-Stops Attenuators 50-Ω Loads Power Distribution Unit DTMAs 203 Summary of Filter, Combiner, Amplifier and Repeater Types The articles are listed by type number in numerical order. Type No. Page Type No. Page Type No. Page Type No. Page 782 10153 309 782 10457 224, 225 782 10635 244, 245 784 10235 299 782 10154 309 782 10458 224, 225 782 10640 246, 247 784 10236 299 299 782 10161 214 782 10460 224, 225 782 10641 246, 247 784 10237 782 10162 214 782 10469 240 782 10642 246, 247 784 10238 299 782 10164 214 782 10474 298 782 10643 246, 247 784 10367 296 782 10165 214 782 10500 256 782 10652 314, 315 784 10470 296 782 10167 215 782 10502 257 782 10653 314, 315 782 10168 210, 211 782 10504 258 782 10660 230 ,231 728 954 223 782 10169 210, 211 782 10524 276, 277 782 10661 230 ,231 790 881 274, 275 782 10170 210, 211 782 10532 259 782 10662 230 ,231 791 145 226 274, 275 782 10171 210, 211 782 10172 210, 211 782 10192 218 782 10193 218 782 10203 260 261 782 10663 230 ,231 791 498 782 10550 287 782 10664 230 ,231 791 918 299 782 10555 306 782 10665 230 ,231 791 919 299 782 10556 306 782 10669 232 ,233 791 920 299 782 10557 306 782 10680 234, 235 791 921 299 216 782 10534 782 10215 212, 213 782 10558 306 782 10681 234, 235 792 542 782 10216 212, 213 782 10561 310 782 10682 234, 235 792 544 217 782 10253 290, 291 782 10562 310 782 10683 234, 235 792 699 253 254 782 10254 290, 291 782 10563 310 782 10800 242, 243 792 702 782 10255 290, 291 782 10564 310 782 10805 264, 265 792 972 300 782 10256 290, 291 782 10565 310 782 10808 240 793 006 279 782 10257 212, 213 782 10566 310 782 10809 241 793 301 283 782 10264 250 782 10567 310 782 10810 241 793 304 285 278 782 10265 212, 213 782 10568 310 782 10811 308 793 506 782 10278 236, 237 782 10569 310 782 10850 284 793 554 280 782 10279 236, 237 782 10570 310 782 10860 316 793 555 255 782 10305 236, 237 782 10571 310 782 10900 248, 249 782 10306 236, 237 782 10577 288 782 10901 248, 249 K 62 26 11 1 296 782 10341 227 782 10578 289 782 10925 266, 267 K 62 26 20 1 297 782 10344 294, 295 782 10579 310 782 10930 268, 269 K 62 26 20 7 297 782 10388 294 782 10580 305 782 10935 270, 271 K 62 26 21 1 297 297 782 10389 294 782 10581 305 782 10936 272, 273 K 62 26 21 7 782 10390 208 782 10610 312 782 10970 228 ,229 K 62 26 30 1 297 782 10391 208 782 10612 312 782 10971 228 ,229 K 62 26 30 7 297 297 782 10392 209 782 10613 313 782 10972 228 ,229 K 62 26 31 1 782 10406 307 782 10620 238, 239 782 10973 228 ,229 K 62 26 31 7 297 782 10415 216 782 10621 238, 239 782 11055 292, 293 K 62 26 40 1 296 782 10429 286 782 10622 238, 239 782 11056 292, 293 K 62 26 41 1 296 782 10430 303 782 10623 238, 239 782 11091 242, 243 K 62 26 50 1 297 297 297 782 10440 304 782 10624 238, 239 782 11092 242, 243 K 62 26 50 7 782 10442 304 782 10625 238, 239 782 11093 242, 243 K 62 26 51 1 782 10448 311 782 10630 244, 245 782 11094 242, 243 K 62 26 61 1 296 K 63 73 62 1 274, 275 782 10453 290, 291 782 10454 290, 291 782 10455 782 10456 204 244, 245 782 11095 242, 243 782 10632 244, 245 782 11100 249 290, 291 782 10633 244, 245 782 11101 249 290, 291 782 10634 244, 245 782 11110 262, 263 782 10631 New Products Filters / Duplexers Filters / Duplexers 205 206 Summary of Filter and Duplexer Types Filters: Description Type No. Frequency range Max. Input power Page 400 W 400 W 400 W 208 208 209 Max. input power Page 400 W 210, 211 400 W 210, 211 400 W 210, 211 400 W 210, 211 400 W 210, 211 400 W 212, 213 400 W 212, 213 400 W 212, 213 800 W 212, 213 500 W 214 500 W 214 500 W 214 500 W 214 250 W 215 250 W 216 250 W 216 300 W 217 250 W 218 250 W 218 ... tunable bandwidth – fixed bandwidth Band-pass Filter Band-pass Filter Band-pass Filter 782 10390 782 10391 782 10392 890 – 960 MHz 890 – 960 MHz 824 – 888 MHz Duplexers: Description Type No. Duplexer 782 10168 Duplexer 782 10169 Duplexer 782 10170 Duplexer 782 10171 Duplexer 782 10172 Duplexer 782 10215 Duplexer 782 10216 Duplexer 782 10257 Duplexer 782 10265 Duplexer 782 10164 Duplexer 782 10165 Duplexer 782 10161 Duplexer 782 10162 Duplexer 782 10167 Duplexer 792 542 Duplexer 782 10415 Duplexer 792 544 Duplexer 782 10192 Duplexer 782 10193 Frequency range Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: 824 – 835 869 – 880 824 – 835 869 – 880 824 – 835 869 – 880 835 – 851 880 – 896 835 – 851 880 – 896 824 – 851 869 – 896 824 – 851 869 – 896 824 – 846.5 869 – 891.5 824 – 846.5 869 – 891.5 890 – 915 935 – 960 890 – 915 935 – 960 890 – 915 935 – 960 890 – 915 935 – 960 880 – 915 925 – 960 1710 – 1785 1805 – 1880 1710 – 1785 1805 – 1880 1850 – 1910 1930 – 1990 1920 – 1980 2110 – 2170 1920 – 1980 2110 – 2170 MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz New Products 207 Band-pass Filter 890 – 960 MHz Port 2 • GSM 900 Tx/Rx preselector filter • Suppression of interfering Tx signals of an adjacent AMPS or CDMA frequency band • Suitable for indoor applications • Built-in DC stop Port 1 782 10390 782 10391 Typical Attenuation Curves Typical Attenuation Curves 10 0 – 888 890 – 960 20 30 Attenuation/dB 0 10 0 – 889 30 40 50 50 60 60 70 70 80 80 90 90 100 865 100 865 875 885 895 905 915 925 935 945 955 965 Frequency/MHz 0.5 1.0 890 – 960 1.5 3.0 3.5 3.5 4.0 4.0 4.5 4.5 915 925 935 945 955 965 5.0 865 875 885 Pass band Insertion loss Stop band attenuation VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 2 Mounting Weight Packing size Dimensions (w x h x d) 208 < < < < 782 10390 782 10391 0 – 888 MHz 2 MHz 0 – 889 MHz 1 MHz 1.5 0.8 0.6 0.3 890 – 960 MHz dB (890 – 892 MHz) dB (892 – 893 MHz) dB (893 – 905 MHz) dB (905 – 960 MHz) > 50 dB (0 – 880 MHz) > 40 dB (880 – 885 MHz) > 30 dB (885 – 888 MHz) < 1.25 (890 – 960 MHz) 945 895 905 915 925 935 945 Frequency/MHz Technical Data Stop band Frequency spacing 935 955 965 955 965 890 – 960 Frequency/MHz Type No. 925 Frequency/MHz 0 – 889 2.5 905 915 1.5 3.0 895 905 1.0 2.0 885 895 0.5 2.5 875 885 0 2.0 5.0 865 875 Diagram II 0 0 – 888 890 – 960 20 40 Diagram II Port 1 Attenuation/dB Port 2 Diagram I Attenuation/dB Attenuation/dB Diagram I 0 890 – 960 MHz < 4.0 dB (890 – 891 MHz) < 2.5 dB (891 – 892 MHz) < 1.0 dB (892 – 893 MHz) < 0.6 dB (893 – 905 MHz) < 0.3 dB (905 – 960 MHz) > 50 dB (0 – 869 MHz) > 30 dB (869 – 889 MHz) < 1.3 (891 – 960 MHz) 50 Ω < 400 W (935 – 960 MHz) < –160 dBc (3rd order; with 2 x 20 W) –20 … +55 °C –5 … +45 °C Port 1: 7-16 female, long neck / Port 2: 7-16 male Indoor Stop With 4 screws (max. 4 mm diameter) 2 kg 387 x 137 x 130 mm 92 x 74 x 338.4 mm (including connectors and mounting feet) Band-pass Filter 824 – 888 MHz (AMPS/CDMA850) • AMPS/CDMA850 Tx/Rx filter • Suppression of spurious emissions at adjacent Port 2 GSM900 Rx frequencys • Suitable for indoor applications Port 1 • Built-in DC stop Port 2 Calculated Attenuation Curves Attenuation/dB Diagram I 0 10 824 – 888 890 – 960 20 30 40 50 60 70 Port 1 80 90 100 820 Technical Data Pass band Insertion loss Stop band attenuation VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 840 850 860 870 880 890 900 910 920 Frequency/MHz 782 10392 824 – 888 MHz < 0.5 dB (824 – 885 MHz) < 0.8 dB (885 – 886 MHz) < 1.5 dB (886 – 888 MHz) > 40 dB (890 – 960 MHz) < 1.25 50 Ω < 400 W (824 – 888 MHz) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +55 °C Port 1: 7-16 female (long neck) / Port 2: 7-16 male Indoor Diagram II Attenuation/dB Type No. 830 0 0.5 1.0 824 – 888 890 – 960 1.5 2.0 2.5 3.0 3.5 4.0 Stop With 4 screws (max. 4 mm diameter) 2 kg 387 x 137 x 130 mm 89 x 73,3 mm x 308.5 mm (including connectors and mounting feet) 4.5 5.0 820 830 840 850 860 870 880 890 900 910 920 Frequency/MHz 209 Duplexer 824 – 835 / 869 – 880 MHz (AMPS A-Band) 835 – 851 / 880 – 896 MHz (AMPS B-Band) The Duplexer is designed to combine/split GSM Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • 78210168: AMPS A-Band, indoor version • 78210169: AMPS A-Band, outdoor version • 78210170: AMPS A-Band, indoor version 782 10168 782 10171 (indoor) mounted onto a 19˝ drawer Low band Antenna High band • 78210171: AMPS B-Band, indoor version • 78210172: AMPS B-Band, outdoor version 782 10169 782 10172 (outdoor) Low band Low band Antenna Low band Antenna Antenna High band High band High band 782 10170 (19˝ drawer) Technical Data Type No. Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 210 782 10168 782 10169 782 10170 782 10171 782 10172 AMPS A-Band AMPS B-Band 824 – 835 MHz 869 – 880 MHz 835 – 851 MHz 880 – 896 MHz < 0.5 dB (824 – 835 MHz) < 0.5 dB (869 – 880 MHz) < 0.5 dB (835 – 851 MHz) < 0.5 dB (880 – 896 MHz) > 85 dB (824 – 835 / 869 – 880 MHz) > 85 dB (835 – 851 / 880 – 896 MHz) < 1.25 (824 – 835 / 869 – 880 MHz) < 1.25 (835 – 851 / 880 – 896 MHz) 50 Ω 50 Ω < 400 W (high band; with max. 8 carriers) < 400 W (high band; with max. 12 carriers) < –160 dBc (3 rd order; with 2 x 20 W) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C –40 ... +60 °C –20 ... +55 °C –20 ... +55 °C –40 ... +60 °C 7-16 female 7-16 female Indoor Outdoor (IP 66) Indoor, 19˝ drawer Indoor Outdoor (IP 66) Built-in DC stop between all ports Built-in DC stop between all ports With 4 screws Wall mounting With 4 screws With 4 screws Wall mounting with 4 screws (max. 4 mm diameter) with 4 screws (max. 6 mm diameter) (max. 4 mm diameter) (max. 8 mm diameter) (max. 8 mm diameter) Mast mounting with Mast mounting with additional clamp set additional clamp set 2.8 kg 5.5 kg 3.7 kg 2.8 kg 5.5 kg 309 x 162 x 252 mm 347 x 297 x 174 mm 612 x 312 x 224 mm 309 x 162 x 252 mm 347 x 297 x 174 mm 229 x 80 x 170 mm 238 x 305 x 93.5 mm 19˝ drawer, 229 x 80 x 170 mm 238 x 305 x 93.5 mm 2 height units, plug- (including connectors (including mounting feet) in depth 170 mm and mounting feet) Duplexer 824 – 835 / 869 – 880 MHz (AMPS A-Band) 835 – 851 / 880 – 896 MHz (AMPS B-Band) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Clamp Set Typical Attenuation Curves (782 10168, 782 10169, 782 10170) Diagram I Diagram II High band ¤ Antenna Antenna ¤ Low band 0 Attenuation/dB Attenuation/dB Antenna ¤ Low band 10 20 824 – 835 869 – 880 30 0.5 1.0 869 – 880 824 – 835 1.5 40 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 100 802 High band ¤ Antenna 0 5.0 812 822 832 842 852 862 872 882 892 902 802 812 822 832 842 852 Frequency/MHz 862 872 882 892 902 Frequency/MHz Typical Attenuation Curves (782 10171, 782 10172) Diagram I Diagram II Antenna ¤ Low band High band ¤ Antenna 0 Attenuation/dB Attenuation/dB Antenna ¤ Low band 10 20 880 – 896 835 – 851 30 0.5 1.0 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 825 835 845 855 865 875 885 895 905 Frequency/MHz 915 880 – 896 835 – 851 1.5 40 100 815 High band ¤ Antenna 0 5.0 815 825 835 845 855 865 875 885 895 905 915 Frequency/MHz 211 Duplexer 824 – 851 / 869 – 896 MHz (AMPS A/B-Band) 824 – 846.5 / 869 – 891.5 MHz (AMPS A/B-Band) 782 10215 782 10257 134 148 ø4 .3 229 219 169.6 The Duplexer is designed to combine/split AMPS Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor application • Built-in DC stop 50 27.5 91.5 59.5 206 max. 80 High Band ø4 .3 Low Band Antenna 229 219 175.4 134 148 782 10216 782 10215, 782 10257 50 27.5 91.5 59.5 206 max. 80 Low Band Antenna 782 10265 High Band ø4 .3 229 219 170 134 148 782 10216 71.5 max. 112 27.5 91.5 59.5 206 Low Band Antenna High Band Technical Data Type No. Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power 782 10215 782 10216 782 10265 AMPS A/B-Band (reduced bandwidth) 824 – 851 MHz 869 – 896 MHz 824 – 846.5 MHz 869 – 891.5 MHz < 0.5 dB (824 – 851 MHz) < 0.5 dB (869 – 896 MHz) < 0.5 dB (824 – 846.5 MHz) < 0.5 dB (869 – 891.5 MHz) > 65 dB (824 – 851 / 869 – 896 MHz) > 70 dB (824 – 846.5 / 869 – 891.5 MHz) < 1.25 (824 – 851 / 869 – 896 MHz) 50 Ω < 400 W (high band; with max. 16 carriers) < 1.25 (824 – 846.5 / 869 – 891.5 MHz) 50 Ω < 400 W (high band; < 800 W (high band; with max. 16 carriers) with max. 32 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C Intermodulation products Temperature range < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 7-16 female 212 782 10257 AMPS A/B-Band N female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 2.6 kg 309 x 252 x 162 mm 229 x 80 x 170 mm 229 x 80 x 175.4 mm (including connectors and mounting feet) 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 2.6 kg Approx. 3 kg 309 x 252 x 162 mm 309 x 252 x 162 mm 229 x 80 x 170 mm 229 x 112 x 170 mm (including connectors and mounting feet) Duplexer 824 – 851 / 869 – 896 MHz (AMPS A/B-Band) 824 – 846.5 / 869 – 891.5 MHz (AMPS A/B-Band) Typical Attenuation Curves (782 10215, 782 10216) Diagram II Diagram I High band ¤ Antenna Antenna ¤ Low band 0 Attenuation/dB Attenuation/dB Antenna ¤ Low band 10 20 824 – 851 869 – 896 30 0.5 1.0 824 – 851 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 820 830 840 850 860 870 880 890 900 5.0 810 910 869 – 896 1.5 40 100 810 High band ¤ Antenna 0 820 830 840 850 860 Frequency/MHz 870 880 890 900 910 Frequency/MHz Typical Attenuation Curves (782 10257) Diagram II Diagram I High band ¤ Antenna Antenna ¤ Low band 0 Attenuation/dB Attenuation/dB Antenna ¤ Low band 10 20 824 – 846.5 869 – 891.5 30 0.5 1.0 824 – 846.5 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 820 830 840 850 860 870 880 890 900 5.0 810 910 869 – 891.5 1.5 40 100 810 High band ¤ Antenna 0 820 830 840 850 860 Frequency/MHz 870 880 890 900 910 Frequency/MHz Typical Attenuation Curves (782 10265) Diagram II Diagram I High band ¤ Antenna Antenna ¤ Low band Attenuation/dB Attenuation/dB Antenna ¤ Low band 0 10 20 824 – 846.5 869 – 891.5 30 0.5 1.0 824 – 846.5 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 820 830 840 850 860 870 880 890 900 Frequency/MHz 910 869 – 891.5 1.5 40 100 810 High band ¤ Antenna 0 5.0 810 820 830 840 850 860 870 880 890 900 910 Frequency/MHz 213 Duplexer 890 – 915 / 935 – 960 MHz (GSM) The Duplexer is designed to combine/split GSM Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • 782 10164: Indoor version with 7-16 female connectors • 782 10165: Indoor version with 7-16/N female connectors • 782 10161: Indoor version with 7-16 female connectors mounted onto a 19˝ drawer • 782 10162: Outdoor version with 7-16 female connectors 782 10164 (indoor) 782 10162 (outdoor) 782 10165 (indoor) 782 10161 (19˝ drawer) Typical Attenuation Curves Diagram I Diagram II High band ¤ Antenna 0 10 20 935 – 960 890 – 915 30 Antenna ¤ Low band Attenuation/dB Attenuation/dB Antenna ¤ Low band 0.5 1.0 935 – 960 890 – 915 1.5 40 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 100 875 High band ¤ Antenna 0 5.0 885 895 905 915 925 935 945 955 965 975 875 885 895 905 915 Frequency/MHz 925 935 945 955 965 975 Frequency/MHz Technical Data Type No. Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Low band High band Antenna Application Special features Mounting Weight Packing size Dimensions (w x h x d) 214 782 10164 782 10165 782 10161 782 10162 890 – 915 MHz 935 – 960 MHz < 0.5 dB (890 – 915 MHz) < 0.5 dB (935 – 960 MHz) > 70 dB (890 – 915 / 935 – 960 MHz) < 1.25 (890 – 915 / 935 – 960 MHz) 50 Ω < 500 W (high band; with max. 16 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female 7-16 female 7-16 female Indoor N female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female Indoor Indoor, 19˝ drawer Built-in DC stop between all ports With 4 screws With 4 screws (max. 4 mm diameter) (max. 6 mm diameter) 2.6 kg 309 x 162 x 252 mm 228.6 x 80 x 169.6 mm (including connectors and mounting feet) –40 ... +60 °C 7-16 female 7-16 female 7-16 female Outdoor (IP 66) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3.5 kg 5.5 kg 612 x 312 x 224 mm 347 x 294 x 174 mm 19˝ drawer, 2 height units, 238 x 93.5 x 305 mm plug-in depth 172 mm (including connectors and mounting brackets) Duplexer 880 – 915 / 925 – 960 MHz (EGSM) The Duplexer is designed to combine/split EGSM Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC Stop Typical Attenuation Curves Diagram I Low band Antenna High band Attenuation/dB Antenna ¤ Low band High band ¤ Antenna 0 10 20 880 – 915 925 – 960 30 40 50 60 Technical Data Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 782 10167 80 880 – 915 MHz 925 – 960 MHz 100 870 90 880 890 900 910 < 0.9 dB (880 – 915 MHz) < 0.9 dB (925 – 960 MHz) 930 940 950 960 970 Diagram II Antenna ¤ Low band > 75 dB (880 – 915 / 925 – 960 MHz) < 1.25 (880 – 915 / 925 – 960 MHz) 50 Ω < 250 W (low band or high band) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +55 °C 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 4.6 kg 347 x 297 x 174 mm 229 x 81 x 260 mm (including connectors and mounting feet) 920 Frequency/MHz Attenuation/dB Type No. 70 High band ¤ Antenna 0 0.5 1.0 880 – 915 925 – 960 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 870 880 890 900 910 920 930 940 950 960 970 Frequency/MHz 215 Duplexer 1710 – 1785 / 1805 – 1880 MHz (GSM 1800) The Duplexer is designed to combine/split GSM 1800 Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop between all ports 792 542 782 10415 Low band Antenna High band Low Band Antenna High Band Typical Attenuation Curves Diagram I Attenuation/dB Antenna ¤ Low band High band ¤ Antenna 0 10 20 1805 – 1880 1710 – 1785 30 40 50 60 Technical Data Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 216 792 542 80 782 10415 90 100 1710 – 1785 MHz 1805 – 1880 MHz 1695 1715 1735 1755 1775 1795 < 0.7 dB (1710 – 1785 MHz) < 0.7 dB (1805 – 1880 MHz) > 65 dB (1710 – 1785 / 1805 – 1880 MHz) < 1.25 (1710 – 1785 / 1805 – 1880 MHz) 50 Ω < 250 W (low band or high band, with max. 8 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Indoor, 19˝ drawer Built-in DC stop between all ports With 4 screws With 4 screws (max. 4 mm diameter) (max. 6 mm diameter) 1.6 kg 2.6 kg 282 x 252 x 114 mm 612 x 312 x 224 mm 192 x 42.5 x 199.6 mm 19˝ drawer, 2 height units (including connectors plug-in depth 184 mm and mounting feet) 1815 1835 1855 1875 1895 Frequency/MHz Diagram II Antenna ¤ Low band Attenuation/dB Type No. 70 High band ¤ Antenna 0 0.5 1.0 1710 – 1785 1805 – 1880 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1695 1715 1735 1755 1775 1795 1815 1835 1855 1875 1895 Frequency/MHz Duplexer 1850 – 1910 / 1930 – 1990 MHz (GSM 1900) The Duplexer is designed to combine/split GSM 1900 Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop Typical Attenuation Curves Diagram I Low Band Antenna High Band Attenuation/dB Antenna ¤ Low band High band ¤ Antenna 0 10 20 1850 – 1910 1930 – 1990 30 40 50 60 70 Technical Data Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 90 792 544 100 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020 Frequency/MHz 1850 – 1910 MHz 1930 – 1990 MHz < 0.7 dB (1850 – 1910 MHz) < 0.7 dB (1930 – 1990 MHz) > 65 dB (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) 50 Ω < 300 W (low band or high band) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 1.7 kg 282 x 252 x 114 mm 192 x 42.5 x 199.6 mm (including connectors and mounting feet) Diagram II Antenna ¤ Low band Attenuation/dB Type No. 80 High band ¤ Antenna 0 0.5 1.0 1850 – 1910 1930 – 1990 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020 Frequency/MHz 217 Duplexer 1920 – 1980 / 2110 – 2170 MHz (UMTS) The Duplexer is designed to combine/split UMTS Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop 782 10193 782 10192 Low band Antenna High band Typical Attenuation Curves Diagram I Antenna ¤ Low band Antenna Attenuation/dB Low band High band High band ¤ Antenna 0 10 20 2110 – 2170 1920 – 1980 30 40 50 Technical Data Pass band Low band High band Insertion loss Antenna ¤ Low band High band ¤ Antenna Isolation Low band ¥ High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 782 10192 782 10193 70 80 1920 – 1980 MHz 2110 – 2170 MHz 90 100 1800 1850 1900 1950 2000 2050 2100 2150 < 0.3 dB (1920 – 1980 MHz) < 0.3 dB (2110 – 2170 MHz) > 90 dB (1920 – 1980 / 2110 – 2170 MHz) < 1.25 (1920 – 1980 / 2110 – 2170 MHz) 50 Ω < 250 W (low band or high band) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +55 °C 7-16 female N female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 1.67 kg 272 x 237 x 119 mm 229 x 46 x 167.6 mm 229 x 46 x 173.4 mm (including connectors and mounting feet) 2200 2250 2300 Frequency/MHz Diagram II Antenna ¤ Low band Attenuation/dB Type No. 60 High band ¤ Antenna 0 0.5 1.0 1920 – 1980 2110 – 2170 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1800 1850 1900 1950 2000 2050 2100 2150 2200 2250 2300 Frequency/MHz 218 Multiband Combiners Multiband Combiners Dual-Band Combiners Triple-Band Combiners Quad-Band Combiners 219 Summary of Multiband Combiner Types Multiband Combiners: Description Type No. Frequency range Max. input power Page Dual-Band Combiner 728 954 Band 1: Band 2: 68 – 470 MHz 870 – 970 MHz 50 W 50 W 223 Dual-Band Combiner 782 10460 Band 1: Band 2: 50 – 470 MHz 806 – 2500 MHz 500 W 500 W 224, 225 Dual-Band Combiner 782 10457 Band 1: Band 2: 87.5 – 470 MHz 806 – 2500 MHz 500 W 500 W 224, 225 Dual-Band Combiner 782 10458 Band 1: Band 2: 87.5 – 470 MHz 806 – 2500 MHz 500 W 500 W 224, 225 Dual-Band Combiner 791 145 Band 1: Band 2: 50 – 1000 MHz 1600 – 2000 MHz 100 W 50 W 226 Dual-Band Combiner 782 10341 Band 1: Band 2: 824 – 880 MHz 890 – 960 MHz 400 W 400 W 227 Dual-Band Combiner 782 10970 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz 200 W 200 W 228, 229 Dual-Band Combiner 782 10971 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz 200 W 200 W 228, 229 Dual-Band Combiner 782 10972 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz 200 W 200 W 228, 229 Dual-Band Combiner 782 10973 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz 200 W 200 W 228, 229 Dual-Band Combiner 782 10660 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10661 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10662 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10663 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10664 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10665 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 230, 231 Dual-Band Combiner 782 10669 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz 650 W 350 W 232, 233 Dual-Band Combiner 782 10680 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz 700 W 650 W 234, 235 Dual-Band Combiner 782 10681 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz 700 W 650 W 234, 235 Dual-Band Combiner 782 10682 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz 700 W 650 W 234, 235 Dual-Band Combiner 782 10683 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz 700 W 650 W 234, 235 Dual-Band Combiner 782 10278 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz 500 W 500 W 236, 237 Dual-Band Combiner 782 10279 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz 500 W 500 W 236, 237 Dual-Band Combiner 782 10305 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz 500 W 500 W 236, 237 Dual-Band Combiner 782 10306 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz 500 W 500 W 236, 237 Dual-Band Combiner 782 10620 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 Dual-Band Combiner 782 10621 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 Dual-Band Combiner 782 10622 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 Dual-Band Combiner 782 10623 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 Dual-Band Combiner 782 10624 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 Dual-Band Combiner 782 10625 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz 300 W 300 W 238, 239 220 Summary of Multiband Combiner Types Multiband Combiners: Description Type No. Frequency range Max. input power Page Dual-Band Combiner 782 10469 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz 250 W 250 W 240 Dual-Band Combiner 782 10808 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz 250 W 250 W 240 Dual-Band Combiner 782 10809 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz 250 W 250 W 241 Dual-Band Combiner 782 10810 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz 250 W 250 W 241 Dual-Band Combiner 782 10800 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 11091 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 11092 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 11093 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 11094 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 11095 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz 300 W 300 W 242, 243 Dual-Band Combiner 782 10264 Band 1: Band 2: 50 – 2200 MHz 2400 – 2500 MHz 200 W 200 W 250 SmartPlex Dual-Band Combiner 782 10900 Band 1: Band 2: 380 – 960 MHz 1710 – 2690 MHz 500 W 300 W 248, 249 SmartPlex Dual-Band Combiner 782 10901 Band 1: Band 2: 380 – 960 MHz 1710 – 2690 MHz 500 W 300 W 248, 249 Triple-Band Combiner 782 10630 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Triple-Band Combiner 782 10631 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Triple-Band Combiner 782 10632 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Triple-Band Combiner 782 10633 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Triple-Band Combiner 782 10634 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Triple-Band Combiner 782 10635 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 700 W 300 W 300 W 244, 245 Quad-Band Combiner 782 10640 Band Band Band Band 1: 2: 3: 4: 380 – 960 1710 – 1880 1920 – 2200 2500 – 2690 MHz MHz MHz MHz 700 300 300 200 W W W W 246, 247 Quad-Band Combiner 782 10641 Band Band Band Band 1: 2: 3: 4: 380 – 960 1710 – 1880 1920 – 2200 2500 – 2690 MHz MHz MHz MHz 700 300 300 200 W W W W 246, 247 Quad-Band Combiner 782 10642 Band Band Band Band 1: 2: 3: 4: 380 – 960 1710 – 1880 1920 – 2200 2500 – 2690 MHz MHz MHz MHz 700 300 300 200 W W W W 246, 247 Quad-Band Combiner 782 10643 Band Band Band Band 1: 2: 3: 4: 380 – 960 1710 – 1880 1920 – 2200 2500 – 2690 MHz MHz MHz MHz 700 300 300 200 W W W W 246, 247 New Products 221 Multiband Combiner – Frequency combinations Dual-Band Combiner, Triple-Band Combiner, Quad-Band Combiner 222 Dual-Band Combiner 68 – 470 MHz 870 – 970 MHz 80 / 160 / 400 MHz GSM 900 • Designed for inhouse multiband distribution Port 1 network • Enables feeder sharing • DC by-pass between port 1 and port 3 Port 2 • Built-in DC stop between port 2 and port 3 12 15 32 18.7 Port 3 ø4.3 Output N coupler 40 105 111.6 Input N coupler 223 Input N coupler 229.4 Typical Attenuation Curves Port 3 Port 1 68 – 470 MHz Port 2 870 – 970 MHz Attenuation/dB Diagram I Port 1 ¥ Port 3 Port 2 ¥ Port 3 68 – 470 870 – 970 0 10 20 30 40 Technical Data Type No. 50 728 954 60 70 Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application DC transparency Port 1 ¥ Port 3 Port 2 ¤ Port 3 Port 3 ¤ Port 2 Weight Packing size Dimensions (w x h x d) 80 68 – 470 MHz 870 – 970 MHz 90 100 < 0.5 dB (68 – 470 MHz) < 0.5 dB (870 – 970 MHz) 0 > 45 dB < 1.2 50 Ω < 50 W < 50 W < –160 dBc (2 nd/3 rd order; with 2 x 20 W) –20 ... +70 °C N female Indoor 100 200 300 400 500 600 700 800 900 1000 Frequency/MHz Diagram II Attenuation/dB Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Port 1 ¥ Port 3 Port 2 ¥ Port 3 68 – 470 870 – 970 0 0.1 0.2 0.3 0.4 0.5 0.6 By-pass (max. 2500mA) short circuited stop 0.8 kg 285 x 55 x 125 mm 229.4 x 32 x 111.6 mm (without connectors) 0.7 0.8 0.9 1.0 0 100 200 300 400 500 600 700 800 900 1000 Frequency/MHz 223 Dual-Band Combiner 50 – 470 MHz 806 – 2500 MHz PMR / TETRA / TETRAPOL CDMA 850 / GSM 900 / GSM 1800 / UMTS 2100 / WLAN • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • External DC stop available as an accessory • Very low insertion loss • High input power Port 3 Port 1 Port 2 782 10457 782 10458 782 10457 782 10458 782 10460 Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Mounting Weight Dimensions (w x h x d) 224 782 10460 87.5 – 470 MHz 806 – 2500 MHz 50 – 470 MHz 806 – 2500 MHz < 0.15 dB (87.5 – 470 MHz) < 0.15 dB (806 – 2500 MHz) < 0.15 dB (50 – 470 MHz) < 0.15 dB (806 – 2500 MHz) > 50 dB (250 – 470 / 806 – 2500 MHz) > 40 dB (87.5 – 250 MHz) < 1.25 (87.5 – 470 / 806 – 960 / 1710 – 2500 MHz) 50 Ω > 50 dB (50 – 470 / 806 – 2500 MHz) < 1.25 (50 – 470 / 806 – 960 / 1710 – 2500 MHz) < 500 W < 500 W < –160 dBc (3 rd order; with 2 x 20 W) –55 ... +60 °C 7-16 female, long neck Indoor or outdoor (IP 66) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4 kg 122 x 52 x 284.7 mm (without connectors, without mounting brackets) Dual-Band Combiner 50 – 470 MHz 806 – 2500 MHz PMR / TETRA / TETRAPOL CDMA 850 / GSM 900 / GSM 1800 / UMTS 2100 / WLAN Typical Attenuation Curves 782 10457 Diagram I Diagram II 0 10 20 806 – 2500 87.5 – 470 Port 1 ¥ Port 3 Port 2 ¥ Port 3 30 Attenuation/dB Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 0.1 0.2 806 – 2500 87.5 – 470 0.3 40 0.4 50 0.5 60 0.6 70 0.7 80 0.8 90 0.9 1.0 100 0 250 500 750 0 1000 1250 1500 1750 2000 2250 2500 250 500 750 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz Frequency/MHz 782 10458 Diagram I Diagram II Port 2 ¥ Port 3 0 10 20 806 – 2500 87.5 – 470 30 Port 1 ¥ Port 3 Attenuation/dB Attenuation/dB Port 1 ¥ Port 3 0.1 0.2 806 – 2500 87.5 – 470 0.3 40 0.4 50 0.5 60 0.6 70 0.7 80 0.8 90 0.9 100 Port 2 ¥ Port 3 0 1.0 0 250 500 750 1000 1250 1500 1750 2000 2250 2500 0 250 500 750 Frequency/MHz 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz 782 10460 Diagram I Diagram II Port 2 ¥ Port 3 0 10 20 806 – 2500 50 – 470 30 Port 1 ¥ Port 3 Attenuation/dB Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 0.1 0.2 50 – 470 806 – 2500 0.3 40 0.4 50 0.5 60 0.6 70 0.7 80 0.8 90 0.9 1.0 100 0 250 500 750 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz 0 250 500 750 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz 225 Dual-Band Combiner 50 – 1000 MHz 1600 – 2000 MHz 80 / 160 / 400 / GSM 900 GSM 1800 • Designed for inhouse multiband distribution network • Enables feeder sharing • DC by-pass between port 1 and port 3 Port 1 Port 2 • Built-in DC stop between port 2 and port 3 Port 3 deep Port 3 Port 1 Port 2 50 – 1000 MHz 1600 – 2000 MHz Typical Attenuation Curves Diagram I Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 10 20 1600 – 2000 50 – 1000 30 40 Technical Data Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR (all ports) Impedance Input power Band 1 Band 2 Temperature range Connectors Application DC transparency Port 1 ¥ Port 3 Port 2 ¤ Port 3 Port 3 ¤ Port 2 Mounting Weight Packing size Dimensions (w x h x d) 791 145 60 70 50 – 1000 MHz 1600 – 2000 MHz 80 < 0.3 dB (50 – 1000 MHz) < 0.5 dB (1600 – 2000 MHz) 100 90 0 200 400 600 800 1000 1200 1400 1600 1800 > 40 dB (50 – 1000 / 1600 – 2000 MHz) < 1.2 (50 – 1000 / 1600 – 2000 MHz) 50 Ω < 100 W < 50 W –30 … +60 °C N female Indoor Diagram II Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 0.1 0.2 1600 – 2000 50 – 1000 0.3 0.4 0.5 By-pass (max. 2500mA) Short circuited Stop With 4 screws (max.4 mm diameter) 0.7 kg 220 x 40 x 140 mm 201 x 23 x 112 mm (incl. connectors) 0.6 0.7 0.8 0.9 1.0 0 200 400 600 800 1000 1200 1400 1600 1800 Frequency/MHz 226 2000 Frequency/MHz Attenuation/dB Type No. 50 2000 Dual-Band Combiner 824 – 880 MHz 890 – 960 MHz AMPS / CDMA 850 GSM 900 • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor applications • Built-in DC stop between all ports Port 1 Port 3 Port 2 Typical Attenuation Curves Diagram I Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 10 20 890 – 960 824 – 880 30 40 50 Technical Data Type No. 60 70 782 10341 80 90 824 – 880 MHz 890 – 960 MHz 100 800 820 840 860 880 900 > 55 dB (824 – 880 / 890 – 960 MHz) < 1.2 (824 – 880 / 890 – 960 MHz) 50 Ω < 400 W (with max. 8 carriers) < 400 W (with max. 8 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 3.2 kg 228 x 85 x 199.3 mm (including connectors and mounting feet) 920 940 960 980 1000 Frequency/MHz < 0.6 dB (824 – 880 MHz) < 0.6 dB (890 – 960 MHz) Diagram II Port 1 ¥ Port 3 Attenuation/dB Pass band Band 1 (AMPS / CDMA 800) Band 2 (GSM 900) Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application Special features Mounting Weight Dimensions (w x h x d) Port 2 ¥ Port 3 0 0.5 1.0 890 – 960 824 – 880 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 800 820 840 860 880 900 920 940 960 980 1000 Frequency/MHz 227 Dual-Band Combiner 790 – 862 MHz 880 – 960 MHz LTE 800 GSM 900 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory Port 3 Port 1 Port 2 782 10970, 782 10972 Single Unit 782 10971, 782 10973 Double Unit Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Lightning protection Mounting Weight Dimensions (w x h x d) 228 782 10970 782 10972 Single Unit Single Unit 782 10971 782 10973 Double Unit Double Unit 790 – 862 MHz 880 – 960 MHz < 0.4 dB, typically 0.2 dB (790 – 862 MHz) < 0.4 dB, typically 0.2 dB (880 – 960 MHz) > 50 dB (790 – 862 MHz / 880 – 960 MHz) < 1.25 (790 – 862 / 880 – 960 MHz) 50 Ω < 200 W / < 200 W < –160 dBc (3 rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.9 kg / Double Unit: 5.8 kg Single Unit: 175 x 51 x 207 mm / Double Unit: 175 x 106 x 207 mm (without connectors, without mounting brackets) Dual-Band Combiner 790 – 862 MHz 880 – 960 MHz LTE 800 GSM 900 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description Typical Attenuation Curves Diagram I Clamp Set Port 1 ¥ Port 3 Port 2 ¥ Port 3 DC stop 50-Ohm load 793 301 784 10367 DC stop 50-Ohm load Diagram II Port 1 ¥ Port 3 Port 2 ¥ Port 3 Side view Single Unit Side view Double Unit Top view Single Unit, Double Unit Please note: Bottom view Single Unit, Double Unit The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 229 Dual-Band Combiner 470 – 960 MHz 1710 – 2700 MHz LTE 800 / CDMA 850 / GSM 900 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory • Extremely small dimensions and low weight • Very low insertion loss • High input power Port 1 Port 3 Port 2 782 10660, 782 10662, 782 10664 Single Unit 782 10661, 782 10663, 782 10665 Double Unit Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products 782 10660 782 10662 782 10664 Single Unit Single Unit Single Unit 782 10661 782 10663 782 10665 Double Unit Double Unit Double Unit 470 – 960 MHz 1710 – 2700 MHz < 0.15 dB (470 – 960 MHz), typically 0.1 dB (470 – 960 MHz) < 0.2 dB (1710 – 2700 MHz), typically 0.1 dB (1710 – 2700 MHz) > 55 dB (470 – 960 MHz) / > 65 dB (1710 – 2700 MHz) < 1.2 (470 – 960 / 1710 – 2700 MHz) 50 Ohm < 650 W / < 350 W < –160 dBc (3 rd order with 2 x 20 W) Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 230 –55 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 1.2 kg / Double Unit: 2.4 kg Single Unit: 285 x 157 x 93 mm / Double Unit: 285 x 157 x 148 mm Single Unit: 126 x 145 x 38 mm / Double Unit: 126 x 145 x 93 mm (without connectors, without mounting brackets) Dual-Band Combiner 470 – 960 MHz 1710 – 2700 MHz LTE 800 / CDMA 850 / GSM 900 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 Accessories (order separately) Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Diagram I Clamp Set Port 1 ¥ Port 3 Attenuation/dB Type No. Typical Attenuation Curves DC stop Port 2 ¥ Port 3 0 -10 -20 1710 – 2700 470 – 960 -30 -40 -50 -60 50-Ohm load Type No. -70 Description -80 782 10850 DC stop 784 10367 50-Ohm load -90 -100 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 -0.1 -0.2 1710 – 2700 470 – 960 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Side view Single Unit Side view Double Unit Top view Single Unit, Double Unit 231 Dual-Band Combiner 470 – 960 MHz 1710 – 2700 MHz LTE 800 / CDMA 850 / GSM 900 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 • Designed to support separate DC/AISG supply for Unit 2 a low-band and high-band DTMA via 2 feeder cables (see application) • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Double unit for XPol antennas • Built-in lightning protection • Extremely small dimensions and low weight • Very low insertion loss • High input power Port 3 Port 1 Port 2 Unit 1 Application Example Technical Data Type No. 782 10669 Double Unit Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 232 470 – 960 MHz 1710 – 2700 MHz < 0.15 dB (470 – 960 MHz), typically 0.1 dB (470 – 960 MHz) < 0.2 dB (1710 – 2700 MHz), typically 0.1 dB (1710 – 2700 MHz) > 55 dB (470 – 960 MHz) / > 65 dB (1710 – 2700 MHz) < 1.2 (470 – 960 / 1710 – 2700 MHz) 50 Ohm < 650 W / < 350 W < –160 dBc (3 rd order with 2 x 20 W) –55 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Unit 1 Unit 2 By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 2.4 kg 285 x 157 x 148 mm 126 x 145 x 93 mm (without connectors, without mounting brackets) Dual-Band Combiner 470 – 960 MHz 1710 – 2700 MHz LTE 800 / CDMA 850 / GSM 900 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 Accessories (order separately) Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Diagram I Clamp Set Port 1 ¥ Port 3 Attenuation/dB Type No. Typical Attenuation Curves DC stop Port 2 ¥ Port 3 0 -10 -20 1710 – 2700 470 – 960 -30 -40 -50 -60 50-Ohm load Type No. -70 Description -80 782 10850 DC stop 784 10367 50-Ohm load -90 -100 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 -0.1 -0.2 1710 – 2700 470 – 960 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Side view Top view 233 Dual-Band Combiner 380 – 960 MHz 1710 – 2700 MHz TETRA / LTE800 / CDMA850 / GSM900 GSM1800 / UMTS / WiMAX / LTE2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory • Extremely low insertion loss • High input power 380 – 960 Port 1 Port 3 Port 2 782 10681, 782 10683 Double Unit 782 10680, 782 10682 Single Unit 380 – 960 1710 – 2700 1710 – 2700 Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 234 782 10680 782 10682 Single Unit Single Unit 782 10681 782 10683 Double Unit Double Unit 380 – 960 MHz 1710 – 2700 MHz < 0.1 dB (380 – 960 MHz) < 0.1 dB (1710 – 2700 MHz) > 55 dB (380 – 550 MHz) / > 65 dB (550 – 960 MHz) / > 65 dB (1710 – 2700 MHz) < 1.2 (380 – 960 / 1710 – 2700 MHz) 50 Ω < 700 W / < 700 W < –160 dBc (3 rd order; with 2 x 20 W) –55 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.2 kg / Double Unit: 4.3 kg Single Unit: 365 x 207 x 150 mm / Double Unit: 365 x 207 x 214 mm Single Unit: 117 x 210 x 50 mm / Double Unit: 117 x 210 x 102 mm (without connectors, without mounting brackets) Dual-Band Combiner 380 – 960 MHz 1710 – 2700 MHz TETRA / LTE800 / CDMA850 / GSM900 GSM1800 / UMTS / WiMAX / LTE2600 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Typical Attenuation Curves Clamp Set Diagram I Port 1 ¥ Port 3 Port 2 ¥ Port 3 DC stop 50-Ohm load Type No. Description 782 10850 DC stop 784 10367 50-Ohm load Diagram II Port 1 ¥ Port 3 Port 2 ¥ Port 3 Side view Single Unit Side view Double Unit Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 235 Dual-Band Combiner 790 – 1880 MHz 1920 – 2170 MHz LTE 800 / CDMA 850 / GSM 900 / GSM 1800 UMTS • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS Port 3 Port 1 or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol an- tennas as a double unit Built-in lightning protection • • External DC Stop available as an accessory Port 2 782 10278, 782 10305 Single Unit 782 10279, 782 10306 Double Unit Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 236 782 10278 782 10305 Single Unit Single Unit 782 10279 782 10306 Double Unit Double Unit 790 – 1880 MHz 1920 – 2170 MHz < 0.1 dB, typically 0.05 dB (790 – 960 MHz) / < 0.4 dB, typically 0.2 dB (1710 – 1880 MHz) < 0.4 dB, typically 0.2 dB (1920 – 2170 MHz) > 55 dB (790 – 960 MHz) / > 50 dB (1710 – 1880 MHz) / > 50 dB (1920 – 2170 MHz) < 1.2 (790 – 960 MHz) / < 1.25 (1710 – 1880 MHz) / < 1.2 (1920 – 2170 MHz) 50 Ω < 500 W / < 500 W < –160 dBc (2 nd/3 rd order; with 2 x 20 W) –55 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.4 kg / Double Unit: 6.6 kg Single Unit: 207 x 437 x 154 mm / Double Unit: 207 x 437 x 214 mm Single Unit: 130 x 269.9 x 43 mm / Double Unit:130 x 269.9 x 98.5 mm (without connectors, without mounting brackets) Dual-Band Combiner 790 – 1880 MHz 1920 – 2170 MHz LTE 800 / CDMA 850 / GSM 900 / GSM 1800 UMTS Accessories (order separately) Clamp set suitable for mast diameter of Clamp Set Diagram I 0 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 40 734 364 120 – 140 mm 50 734 365 45 – 125 mm 60 DC stop 50-Ohm load Type No. Description 793 301 DC stop 784 10367 Port 2 ¥ Port 3 Port 1 ¥ Port 3 Attenuation/dB Type No. Typical Attenuation Curves 10 20 1920 – 2170 790 – 1880 30 70 80 90 100 500 50-Ohm load 700 900 1100 1300 1500 1700 1900 2100 2300 2500 Frequency/MHz Diagram II Port 2 ¥ Port 3 Attenuation/dB Port 1 ¥ Port 3 0 0.1 0.2 790 – 1880 1920 – 2170 0.3 0.4 Side view, Single Unit 0.5 0.6 0.7 0.8 0.9 1.0 500 700 900 1100 1300 1500 1700 1900 2100 2300 2500 Frequency/MHz Side view, Double Unit Top view, Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 10) and replaced with other means of mounting, always provided that the max. drilled depth of 8.5 mm is respected with the choice of replacement screws. 4 screws M5 x 10 4 spring washers 5.5 DIN 6095 Bottom view, Single Unit, Double Unit 237 Dual-Band Combiner 1710 – 1880 MHz 1920 – 2170 MHz GSM 1800 UMTS 2100 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS Port 3 Port 1 or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory Port 2 782 10620, 782 10622, 782 10624 Single Unit 782 10621, 782 10623, 782 10625 Double Unit Technical Data Type No. Pass band Band 1 (GSM 1800) Band 2 (UMTS) Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 ¥ Port 3 Port 2 ¥ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 238 782 10620 782 10622 782 10624 Single Unit Single Unit Single Unit 782 10621 782 10623 782 10625 Double Unit Double Unit Double Unit 1710 – 1880 MHz 1920 – 2170 MHz < 0.3 dB (1710 – 1880 MHz) < 0.3 dB (1920 – 2170 MHz) > 50 dB (1710 – 1880 / 1920 – 2170 MHz) < 1.25 (1710 – 1880 / 1920 – 2170 MHz) 50 Ω < 300 W / < 300 W < –160 dBc (3 rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.9 kg / Double Unit: 5.7 kg Single Unit: 392 x 272 x 139 mm / Double Unit: 392 x 272 x 189 mm Single Unit: 199 x 199 x 48 mm / Double Unit: 199 x 199 x 100 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 – 1880 MHz 1920 – 2170 MHz GSM 1800 UMTS 2100 Accessories (order separately) Type No. Typical Attenuation Curves Clamp Set Clamp set suitable for mast diameter of Diagram I 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm -40 734 365 45 – 125 mm -50 Type No. Description 793 301 DC stop Attenuation/dB 734 360 DC stop 50-Ohm load 0 -10 -20 1710 – 1880 1920 – 2170 -30 -60 -70 -80 50-Ohm load -90 -100 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 Frequency/MHz Diagram II Port 1 ¥ Port 3 Side view Single Unit Attenuation/dB 784 10367 Port 2 ¥ Port 3 Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 -0.1 -0.2 1710 – 1880 1920 – 2170 -0.3 -0.4 Side view Double Unit -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 Frequency/MHz Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 239 Dual-Band Combiner 1850 – 1910 / 1930 – 1990 MHz 1710 – 1755 / 2110 – 2155 MHz PCS AWS • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor or outdoor applications • With fault detection and integrated switch for multiple DC power supply COM ANT AWS PCS 782 10469 Typical Attenuation Curves Diagram I Technical Data Pass band Band 1 (PCS) Band 2 (AWS) Insertion loss Port PCS ¥ Port ANT Port AWS ¥ Port ANT Isolation Port PCS ¥ Port AWS VSWR Impedance Input power Port PCS Port AWS Intermodulation products Power supply voltage operational survival Polarity protection Max. Current Power supply current at PCS port operating with dummy load Lightning protection Temperature range Connectors Application Weight Dimensions (w x h x d) 240 782 10469 782 10808 Single unit Double unit Port Port PCS ¥ ANT Port Port AWS ¥ ANT 0 -10 1850 – 1910 -20 -30 1930 – 1990 1710 – 1755 2110 – 2155 -40 -50 1850 – 1910 (Rx) / 1930 – 1990 (Tx) MHz 1710 – 1755 (Rx) / 2110 – 2155 (Tx) MHz -60 -70 < 0.3 dB (1850 – 1910 / 1930 – 1990 MHz) < 0.2 dB (1710 – 1755 / 2110 – 2155 MHz) -80 -90 > 50 dB (1850 – 1910 / 1930 – 1990 MHz) > 50 dB (1710 – 1755 / 2110 – 2155 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1710 – 1755 / 2110 – 2155 MHz) 50 Ω < 250 W (1850 – 1910 / 1930 – 1990 MHz) < 250 W (1710 – 1755 / 2110 – 2155 MHz) < –160 dBc (3 rd order; with 2 x 20 W) +10 … +15 V DC (Port PCS) +10 … +30 V DC (Port AWS) +10 … +35 V DC –48 V DC (Port PCS, Port AWS) 1.5 A (Port ANT) -100 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz Diagram II Port Port AWS ¥ ANT Attenuation/dB Type No. Attenuation/dB Port Port AWS ¥ ANT Port Port PCS ¥ ANT Port Port AWS ¥ ANT 0 -0.1 -0.2 2110 – 2155 1710 – 1755 -0.3 1850 – 1910 -0.4 1930 – 1990 -0.5 100 mA ±20 mA (+10 ... +15 V DC) 8/20 μs, 20 kA; 10/350 μs, 3 kA (Port ANT) –40 ... +65 °C 7-16 female (long neck) Indoor or outdoor (IP 66) 2.5 kg 5 kg 122 x 216.3 x 47 mm 122 x 216.3 x 102.6 mm (without connectors, without mounting brackets) -0.6 -0.7 -0.8 -0.9 -1.0 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz Dual-Band Combiner 1850 – 1910 / 1930 – 1990 MHz 1710 – 1755 / 2110 – 2155 MHz PCS AWS • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor or outdoor applications • DC by-pass between all ports • External DC stop available as an accessory COM ANT AWS PCS 782 10809 Typical Attenuation Curves Diagram I Attenuation/dB Port Port AWS ¥ ANT Port Port PCS ¥ ANT Port Port AWS ¥ ANT 0 -10 1850 – 1910 -20 -30 1710 – 1755 1930 – 1990 2110 – 2155 -40 -50 -60 Technical Data Pass band Band 1 (PCS) Band 2 (AWS) Insertion loss Port PCS ¥ Port ANT Port AWS ¥ Port ANT Isolation Port PCS ¥ Port AWS VSWR Impedance Input power Port PCS Port AWS Intermodulation products Lightning protection Temperature range Connectors Application DC/AISG transparency Weight Dimensions (w x h x d) 782 10809 782 10810 Single unit Double unit -80 -90 -100 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 1850 – 1910 (Rx) / 1930 – 1990 (Tx) MHz 1710 – 1755 (Rx) / 2110 – 2155 (Tx) MHz Frequency/MHz < 0.3 dB (1850 – 1910 / 1930 – 1990 MHz) < 0.2 dB (1710 – 1755 / 2110 – 2155 MHz) > 50 dB (1850 – 1910 / 1930 – 1990 MHz) > 50 dB (1710 – 1755 / 2110 – 2155 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1710 – 1755 / 2110 – 2155 MHz) 50 Ω < 250 W (1850 – 1910 / 1930 – 1990 MHz) < 250 W (1710 – 1755 / 2110 – 2155 MHz) < –160 dBc (3 rd order; with 2 x 20 W) 3 kA, 10/350 μs pulse –40 ... +65 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass between all ports (max. 2500 mA) 2.5 kg 5 kg 122 x 216.3 x 47 mm 122 x 216.3 x 102.6 mm (without connectors, without mounting brackets) Diagram II Port Port AWS ¥ ANT Attenuation/dB Type No. -70 Port Port PCS ¥ ANT Port Port AWS ¥ ANT 0 -0.1 -0.2 2110 – 2155 1710 – 1755 -0.3 1850 – 1910 -0.4 1930 – 1990 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz 241 Dual-Band Combiner 1710 – 2180 MHz 2400 – 2700 MHz GSM1800 / PCS1900 / AWS / UMTS2100 WLAN / WiMAX / BRS/ LTE2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory • Very low insertion loss 1710 – 2180 2400 – 2700 Port 3 Port 1 Port 2 782 10800, 782 11092, 782 11094 Single Unit 1710 – 2180 782 11091, 782 11093, 782 11095 Double Unit 2400 – 2700 1710 – 2180 2400 – 2700 Technical Data Type No. 782 10800 782 11092 782 11094 Single Unit Single Unit Single Unit 782 11091 782 11093 782 11095 Double Unit Double Unit Double Unit Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products 1710 – 2180 MHz 2400 – 2700 MHz < 0.15 dB < 0.15 dB > 60 dB < 1.25 (1710 – 2180 / 2400 – 2700 MHz) 50 Ω < 300 W / < 300 W < –160 dBc (3 rd order with 2 x 20 W) Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 242 –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.9 kg / Double Unit: 5.7 kg Single Unit: 392 x 272 x 139 mm / Double Unit: 392 x 272 x 189 mm Single Unit: 199 x 199 x 44 mm / Double Unit: 199 x 199 x 95 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 – 2180 MHz 2400 – 2700 MHz GSM1800 / PCS1900 / AWS / UMTS2100 WLAN / WiMAX / BRS/ LTE2600 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description Clamp Set Typical Attenuation Curves Diagram I Port 1 Port 3 Port 2 Port 3 Port 2 Port 3 DC stop 50-Ohm load 782 10850 DC stop 784 10367 50-Ohm load Diagram II Port 1 Port 3 Single Unit Side view Double Unit Side view Top view Single Unit Double Unit Please note: The mounting plates can be removed by loosening the to (M5 x 12) and replaced with other screws means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. Bottom view Single Unit Double Unit 243 Triple-Band Combiner 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz TETRA, LTE 800, CDMA 850, GSM 900 GSM 1800 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory UMTS 2100 Port 4 Port 1 Port 2 Port 3 782 10630, 782 10632, 782 10634 Single Unit 782 10631, 782 10633, 782 10635 Double Unit Technical Data Type No. Pass band Band 1 (TETRA ... GSM 900) Band 2 (GSM 1800) Band 3 (UMTS) Insertion loss Port 1 Port 4 Port 2 Port 4 Port 3 Port 4 Isolation Port 1 Port 2 Port 1 Port 3 Port 2 Port 3 VSWR Impedance Input power Band 1 / Band 2 / Band 3 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 4 Port 2 Port 4 Port 3 Port 4 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 244 782 10630 782 10632 782 10634 Single Unit Single Unit Single Unit 782 10631 782 10633 782 10635 Double Unit Double Unit Double Unit 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz < 0.2 dB ( 380 – 960 MHz) < 0.3 dB (1710 – 1880 MHz) < 0.3 dB (1920 – 2170 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1710 – 1880 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1920 – 2170 MHz) > 50 dB (1710 – 1880 / 1920 – 2170 MHz) < 1.25 (380 – 960 / 1710 – 1880 / 1920 – 2170 MHz) 50 Ω < 700 W / < 300 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) Stop 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.2 kg / Double Unit: 6.3 kg Single Unit: 392 x 292 x 139 mm / Double Unit: 392 x 292 x 189 mm Single Unit: 219 x 199 x 48 mm / Double Unit: 219 x 199 x 104 mm (without connectors, without mounting brackets) Triple-Band Combiner 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz TETRA, LTE 800, CDMA 850, GSM 900 GSM 1800 UMTS 2100 Accessories (order separately) Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Typical Attenuation Curves Clamp Set Diagram I Port 1 ¥ Port 4 Attenuation/dB Type No. DC stop Description 782 10850 DC stop 784 10367 50-Ohm load Port 3 ¥ Port 4 10 20 1920 – 2170 380 – 960 30 1710 – 1880 40 50 50-Ohm load Type No. Port 2 ¥ Port 4 0 60 70 80 90 100 300 500 700 900 1100 1300 1500 1700 1900 2100 2300 Frequency/MHz Side view Single Unit Diagram II Side view Double Unit Attenuation/dB Port 1 ¥ Port 4 Port 2 ¥ Port 4 Port 3 ¥ Port 4 0 0.1 0.2 1920 – 2170 380 – 960 0.3 1710 – 1880 0.4 0.5 0.6 0.7 0.8 0.9 Top view Single Unit, Double Unit 1.0 300 500 700 900 1100 1300 1500 1700 1900 2100 2300 Frequency/MHz Bottom view Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 245 Quad-Band Combiner 380 – 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz GSM 1800 UMTS 2100 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory LTE 2600 Port 1 Port 5 Port 2 Port 3 Port 4 782 10641, 782 10643 Double Unit 782 10640, 782 10642 Single Unit Technical Data Type No. Pass band Band 1 (TETRA ... GSM 900) Band 2 (GSM 1800) Band 3 (UMTS) Band 4 (LTE 2600) Insertion loss Port 1 Port 5 Port 2 Port 5 Port 3 Port 5 Port 4 Port 5 Isolation Port 1 Port 2 Port 1 Port 3 Port 1 Port 4 Port 2 Port 3 Port 2 Port 4 Port 3 Port 4 VSWR Impedance Input power Band 1 / Band 2 / Band 3 / Band 4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 5 Port 2 Port 5 Port 3 Port 5 Port 4 Port 5 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 246 782 10640 782 10642 Single Unit Single Unit 782 10641 782 10643 Double Unit Double Unit 380 1710 1920 2500 < < < < 0.2 0.3 0.3 0.2 dB dB dB dB – – – – 960 1880 2200 2690 ( 380 (1710 (1920 (2500 – – – – MHz MHz MHz MHz 960 1880 2200 2690 MHz) MHz) MHz) MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1710 – 1880 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1920 – 2200 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 2500 – 2690 MHz) > 50 dB (1710 – 1880 / 1920 – 2200 MHz) > 50 dB (1710 – 1880 / 2500 – 2690 MHz) > 50 dB (1920 – 2200 / 2500 – 2690 MHz) < 1.25 (380 – 960 / 1710 – 1880 / 1920 – 2200 / 2500 – 2690 MHz) 50 Ω < 700 W / < 300 W / < 300 W / < 200 W < –160 dBc (3 rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass By-pass By-pass By-pass (max. (max. (max. (max. 2500 2500 2500 2500 mA) mA) mA) mA) Stop Stop Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.8 kg / Double Unit: 7.5 kg Single Unit: 392 x 292 x 139 mm / Double Unit: 392 x 292 x 189 mm Single Unit: 215 x 228 x 50 mm / Double Unit: 215 x 228 x 106 mm (without connectors, without mounting brackets) Quad-Band Combiner 380 – 960 MHz 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 GSM 1800 UMTS 2100 LTE 2600 Accessories (order separately) Clamp Set Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Diagram I Port 1 ¥ 5 Attenuation/dB Type No. Typical Attenuation Curves DC stop Port 2 ¥ 5 Port 3 ¥ 5 Port 4 ¥ 5 0 10 2500 – 2690 20 1920 – 2200 380 – 960 30 1710 – 1880 40 50 60 50-Ohm load 70 Type No. Description 782 10850 DC stop 90 784 10367 50-Ohm load 100 80 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Attenuation/dB Port 1 ¥ 5 Side view Single Unit Port 2 ¥ 5 Port 3 ¥ 5 Port 4 ¥ 5 0 1710 – 1880 2500 – 2690 0.1 0.2 380 – 960 1920 – 2200 0.3 0.4 0.5 0.6 0.7 Side view Double Unit 0.8 0.9 1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 247 SmartPlex ® Dual-Band Combiner 380 – 960 MHz 1710 – 2690 MHz TETRA / LTE 800 / DD / CDMA / GSM 900 GSM / PCS / AWS / UMTS 2100 / LTE • Universal multi-protocol dual-band combiner AISG 1.1 AISG 2.0 3GPP Current window alarming (CWA) Vendor specific protocols Main 2 Main 1 Div 1 Div 2 • Designed for co-siting purposes • Enables feeder sharing • 782 10900: For use near the base station (BTS), thereby converting different base station DC voltages into one common feeder DC voltage (multi-BTS power supply handling) 782 10901: For use near the antenna (ANT), thereby reproducing the base station DC voltages for the antenna line devices 782 10901 Feeder Main AISG Feeder Div • Simultaneous support of antenna line devices (TMAs, RET units) Feeder Main Feeder Div • Dynamic DC/AISG by-pass: Automatic setting on each RF path according to the BTS and antenna line device requirements • DC power supply either from BTS via RF path, or from an external source via AISG port (782 10900) • Provides full Smart Bias Tee functionality • Suitable for indoor or outdoor applications • Wall or mast mounting • Double unit in one housing for XPol antennas • Built-in lightning protection • Very low insertion loss • High input power 782 10900 Main 2 Main 1 AISG Div 1 Div 2 Technical Data Type No. Pass band Band 1 / Band 2 Insertion loss Isolation Main 1 Main 2 / Div 1 Div 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors RF AISG Power consumption DC supply Application DC/AISG transparency Lightning protection Mounting Weight Dimensions (w x h x d) 248 782 10901 (ANT) 782 10900 (BTS) 380 – 960 / 1710 – 2690 MHz < 0.2 dB, typically 0.15 dB (380 – 960 / 1710 – 2690 MHz) > 60 dB (380 – 960 / 1710 – 2690 MHz) < 1.22 (380 – 960 / 1710 – 2690 MHz) 50 Ohm < 500 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) 8-pin, IEC 60130-9 (782 10900/901: Male/female) Pin 2: -48V DC (782 10900 only), Pin 3: RS485B, Pin 5: RS485A, Pin 6: Nominal 24 V DC, Pin 7: DC return (78210900/901: Not grounded/grounded), Other pins: Not connected 2 W (idle mode) 782 10900: 7 – 30 V DC (via RF connectors) Indoor or outdoor (IP 67) For AISG 1.1, AISG 2.0, 3GPP, vendor specific protocols and for current window alarm (CWA) controlled TMAs 3 kA (10/350 μs pulse), 10 kA (8/20 μs pulse) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 782 10900: 6.5 kg, 782 10901: 4.9 kg 782 10900: 233 x 258 x 79 mm 782 10901: 233 x 223 x 62 mm (without connectors, without mounting brackets) Application Example SmartPlex ® Dual-Band Combiner 380 – 960 MHz TETRA / LTE 800 / DD / CDMA / GSM 900 1710 – 2690 MHz GSM / PCS / AWS / UMTS 2100 / LTE Accessories (order separately) Typical Attenuation Curves Clamp Set Diagram I Port 1 ¥ Port 3 Attenuation/dB Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm -40 734 365 45 – 125 mm -50 Type No. Description 50-Ohm load Port 2 ¥ Port 3 0 -10 -20 380 – 960 1710 – 2690 -30 -60 -70 784 10367 50-Ohm load 1.5 W / indoor or outdoor -80 782 11100 DC cable kit –48 VDC -90 782 11101 DC cable kit +24 VDC -100 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II 782 10901 Attenuation/dB Port 1 ¥ Port 3 Port 2 ¥ Port 3 0 -0.1 -0.2 380 – 960 1710 – 2690 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz 782 10900 249 Dual-Band Combiner 50 – 2200 MHz 2400 – 2500 MHz 80 / 160 / 400 / 800 / 900 / 1800 / 2100 WLAN • Designed for inhouse multiband distribution networks • Enables feeder sharing • DC by-pass between ports 1 and 3 • Built-in DC stop between ports 2 and 3 Port 3 Port 1 Port 2 Typical Attenuation Curves Diagram I Port 2 ¥ Port 3 Attenuation/dB Port 1 ¥ Port 3 0 10 2400 – 2500 20 50 – 2200 30 40 Technical Data 50 Pass band Band 1 Band 2 Insertion loss Port 1 ¥ Port 3 Port 2 ¥ Port 3 Isolation Port 1 ¥ Port 2 VSWR Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 250 782 10264 60 70 50 – 2200 MHz 2400 – 2500 MHz 80 90 < 0.1 dB (50 – 2200 MHz) < 0.2 dB (2400 – 2500 MHz) > 50 dB (50 – 2200 / 2400 – 2500 MHz) < 1.25 (50 – 2200 / 2400 – 2500 MHz) 50 Ω < 200 W < 200 W < –150 dBc (3rd order; with 2 x 20 W) –20 ... +55 °C N female Indoor Built-in DC stop between ports 2 and 3 DC by-pass between ports 1 and 3 (max. 2500 mA) With 4 screws (max. 4 mm diameter) 0.47 kg 225 x 140 x 75 mm 86 x 30.4 x 181.4 mm (including connectors and mounting feet) 100 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Port 1 ¥ Port 3 Attenuation/dB Type No. Port 2 ¥ Port 3 0 0.1 2400 – 2500 0.2 50 – 2200 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Same-Band / Hybrid Combiners Same-Band Combiners Hybrid Combiners Same-Band Combiner Duplex Hybrid Combiner Active Duplex Hybrid Combiner Hybrid Combiner 2 : 1 Hybrid Combiner 4 : 4 3-dB Couplers Hybrid Ring Junctions 251 Summary of Same-Band Combiner and Hybrid Combiner Types Hybrid Combiners and Couplers: Description Type No. Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 4:4 Hybrid Combiner 4:4 Hybrid Combiner 4:4 Active Duplex Hybrid Combiner Duplex Hybrid Combiner 792 792 793 782 782 782 782 782 782 782 699 702 555 10500 10502 10504 10532 10203 10534 11110 78210805 Same-Band Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Hybrid Ring Junction Hybrid Ring Junction Hybrid Ring Junction 3-dB Coupler 3-dB Coupler 3-dB Coupler 3-dB Coupler 782 10925 782 10930 782 10935 782 10936 K 63 73 62 1 790 881 791 498 782 10524 793 506 793 006 793 554 New Products 252 Frequency range 806 – 960 1700 – 2200 800 – 2200 806 – 960 1710 – 2170 698 – 2690 1710 – 2170 800 – 2200 698 – 2600 Rx: 880 – 915 Tx: 925 – 960 Rx: 880 – 915 Tx: 925 – 960 1920 – 2170 880 – 960 880 – 960 880 – 960 806 – 960 890 – 960 1710 – 1880 698 – 2690 806 – 960 1700 – 2200 800 – 2200 MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz Max. input power Connector Page 150 W per Tx/Rx port 150 W per Tx/Rx port 150 W per Tx/Rx port 60 W at each port 60 W at each port 60 W at each port 60 W at each port 150 W at each port 150 W at each port 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 253 254 255 256 257 258 259 260 261 250 W 7-16 262, 263 250 W 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W per input 100 W per input 50 W per input 150 W at each port 500 W 300 W 300 W 7-16 7-16 7-16 7-16 7-16 N N N 7-16 7-16 7-16 7-16 264, 265 266, 267 268, 269 270, 271 272, 273 274, 275 274, 275 274, 275 276, 277 278 279 280 Hybrid Combiner 2:1 806 – 960 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications • Wall or 19´´ rack mounting • DC by-pass between port 1 and port 3 • External DC stop available as an accessory Technical Data Type No. Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) Tx/Rx2 Attenuation Tx/Rx1 / dB Attenuation Tx1 × Tx/Rx2 Tx2 / dB Typical attenuation Tx/Rx1 vs. Antenna VSWR 25 792 699 806 – 960 MHz 3.1 ±0.4 dB 3.1 ±0.4 dB > 27 dB * < 1.11 50 Ω 20 15 < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor By-pass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 10.3 kg 510 x 410 x 100 mm 336 x 444 x 64 mm * Valid if all ports are terminated with 50-Ω loads (see diagram). 1.0 1.5 2.0 Antenna VSWR Antenna VSWR Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. 253 Hybrid Combiner 2:1 1700 – 2200 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna • The frequency spacing between transmitter Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications • Wall or 19´´ rack mounting • DC by-pass between port 1 and port 3 • External DC stop available as an accessory Type No. Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 792 702 1700 – 2200 MHz 3.1 ±0.4 dB 3.1 ±0.4 dB > 24 dB* < 1.15 50 Ω < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor By-pass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 9.8 kg 510 x 410 x 100 mm 336 x 444 x 64 mm * Valid if all ports are terminated with 50-Ω loads (see diagram). 254 Attenuation Tx/Rx1 Technical Data Tx/Rx2 Tx/Rx2 / dB Typical attenuation Tx/Rx1 vs. Antenna VSWR Antenna VSWR Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. Hybrid Combiner 2:1 800 – 2200 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna • The frequency spacing between transmitter Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications • Wall or 19´´ rack mounting • DC by-pass between port 1 and port 3 • External DC stop available as an accessory Type No. Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 793 555 800 – 2200 MHz 3.1 ±1.2 dB 3.1 ±1.2 dB > 22 dB* < 1.2 50 Ω < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor By-pass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 10 kg 510 x 410 x 100 mm 336 x 444 x 64 mm * Valid if all ports are terminated with 50-Ω loads (see diagram) Attenuation Port 1 Technical Data Port 2 Port 2 / dB Typical attenuation Port 1 vs. VSWR at Port 3 VSWR at Port 3 Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. 255 Hybrid Combiner 2:1 806 – 960 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC by-pass between all ports • External DC stop available as an accessory Port 3 Port 1 Port 2 Technical Data Type No. 782 10500 Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency 806 – 960 MHz Mounting Weight Packing size Dimensions (w x h x d) 3.1 ±0.5 dB 3.1 ±0.5 dB > 23 dB * < 1.15 50 Ω < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass between all ports (max. 2500 mA) AISG: Attenuation 3 dB with / 6 dB without external DC stop at either Port 1 or Port 2 Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set (see data sheet) 3.7 kg 377 x 232 x 189 mm 143.6 x 258 x 97.5 mm (including connectors) * Valid if all ports are terminated with 50-Ω loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted horizontally, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If mounted vertically and/or used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Mounted horizontally Mounted vertically 60 W 70 W 75 W 70 W 80 W 85 W Max. ambient temperature +55 °C +40 °C +25 °C 256 Earth screw M8 x 10 Hybrid Combiner 2:1 1710 – 2170 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC by-pass between all ports • External DC stop available as an accessory Port 1 Port 2 Technical Data 782 10502 Type No. Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 1710 – 2170 MHz 3.1 ±0.5 dB 3.1 ±0.5 dB > 22 dB * < 1.25 50 Ω < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass between all ports (max. 2500 mA) AISG: Attenuation 3 dB with / 6 dB without external DC stop at either Port 1 or Port 2 Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set 3.7 kg 377 x 232 x 189 mm 143.6 x 256 x 97.5 mm (including connectors) * Valid if all ports are terminated with 50-Ω loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted horizontally, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If mounted vertically and/or used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Mounted horizontally Mounted vertically 60 W 70 W 75 W 70 W 80 W 85 W Max. ambient temperature +55 °C +40 °C +25 °C Earth screw M8 x 10 257 Hybrid Combiner 2:1 698 – 2690 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna • The frequency spacing between transmitter signals can be as small as required Port 1 • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC by-pass between port 1 and port 3 Port 3 Port 2 Technical Data Type No. 782 10504 Frequency range Attenuation Port 1 Port 3 Port 2 Port 3 Port 1 Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Mounting 698 – 2690 MHz Weight Packing size Dimensions (w x h x d) 3.1 ±0.5 dB 3.1 ±0.5 dB > 23 dB* < 1.2 (698 – 2170 MHz) / < 1.25 (2170 – 2690 MHz) 50 Ω < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) Stop Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4.3 kg 385 x 345 x 168 mm 264 x 203 x 72.5 mm (without connectors, without mounting brackets) * Valid if all ports are terminated with 50-Ohm loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Mounted horizontally Mounted vertically 55 W 70 W 80 W 60 W 75 W 85 W Max. ambient temperature +55 °C +40 °C +25 °C 258 Hybrid Combiner 4:4 1710 – 2170 MHz 4 x 60 W • Designed for the decoupled combining of 4 transmitter or receiver signals and distributing these signals equally onto 4 antenna outputs • Suitable for indoor or outdoor applications • Wall or mast mounting • DC by-pass between all ports • External DC stop available as an accessory Outputs 1...4 Inputs 1...4 Technical Data 782 10532 Type No. Frequency range Insertion Loss Input 1...4 Output 1...4 Power distribution loss (excluding insertion loss) Input 1...4 Output 1...4 Isolation Input 1...4 Input 1...4 Output 1...4 Output 1...4 VSWR (all ports) Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 1710 – 2170 MHz 0.5 dB ±0.2 dB 6 ±0.75 dB > 22 dB* > 22 dB* < 1.25 50 Ω < 60 W at each port < –160 dBc (3 rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass between all ports (max. 2500 mA) External DC stop available as an accessory Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4.4 kg 357 x 312 x 189 mm 271 x 262 x 89.5 mm (including connectors and mounting brackets) * Valid if all ports are terminated with 50-Ω loads Note: The use of fewer than 4 inputs or outputs is possible. Any unused input ports have to be terminated with low-power 50-Ohm loads (e.g. Kathrein type 784 10367), unused output ports have to be terminated with high-power 50-Ohm loads (e.g. Kathrein low-intermodulation type 782 10474). 259 Hybrid Combiner 4:4 800 – 2200 MHz 4 x 150 W • Designed for the decoupled combining of 4 transmitter or receiver signals and distributing these signals evenly onto 4 antenna outputs. Technical Data Type No. 782 10203 Frequency range 800 – 2200 MHz Power distribution loss (including insertion loss) Input 1...4 Output 1...4 < 6.5 ±2 dB Insertion Loss < 0.5 dB Isolation Input 1...4 Input 1...4 > 20 dB Output 1...4 Output 1...4 > 20 dB VSWR (all ports) < 1.3 * Impedance 50 Ω Input power < 150 W at each port Intermodulation products < –155 dBc (3 rd order; with 2 x 20 W) Temperature range –40 … +60 °C Connectors 7-16 female Application Indoor Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Dimensions (w x h x d) 360 x 180 x 216 mm * Valid if all ports are terminated with 50-Ω loads. Note: The use of fewer than 4 inputs or outputs is possible. Any unused input ports have to be terminated with low-power 50-Ω loads (e.g. Kathrein type 784 10367), unused output ports have to be terminated with high-power 50-Ω loads (e.g. Kathrein low-intermodulation type 782 10474). 260 Output 1 Input 1 Output 2 Output 3 3-dB Coupler 3-dB Coupler 3-dB Coupler 3-dB Coupler Input 2 Input 3 Output 4 Input 4 Hybrid Combiner 4:4 698 – 2690 MHz 4 x 150 W • Designed for the decoupled combining of 4 Output 1 transmitter or receiver signals and distributing these signals equally onto 4 antenna outputs Output 2 Output 3 • Suitable for indoor or outdoor applications • DC/AISG by-pass • External DC stop available as an accessory Output 4 Input 1 Input 2 Input 3 Input 4 Technical Data Type No. 782 10534 Frequency range Insertion loss Input 1...4 Output 1...4 Power distribution loss (excluding insertion loss) Input 1...4 Output 1...4 Isolation Input 1...4 Input 1...4 Output 1...4 Output 1...4 VSWR (all ports) Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency 698 – 2690 MHz Mounting Weight Packing size Dimensions (w x h x d) 0.5 ±0.2 dB 6 ±0.75 dB > 22 dB* > 22 dB* < 1.3 50 Ω < 150 W at each input port < –160 dBc (3 rd order; with 2 x 20 W) –40 … +60 °C 7-16 female Indoor or outdoor (IP 66) By-pass (max. 2500 mA) between Input 1 Output 4 / Input 2 Output 2 / Input 3 Output 3 / Input 4 Output 1 External DC stop available as an accessory Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional mounting kit Max. 3.9 kg 452 x 272 x 124 mm 365.9 x 63 x 214.2 mm (with connectors and mounting feet) * Valid if all ports are terminated with 50-Ohm loads Accessories (order separately) Type No. Description 782 10850 DC stop 782 10474 50-Ohm load (80 W) 784 10367 50-Ohm load (1.5 W) 782 10535 Mast mounting kit DC stop 50-Ohm load 50-Ohm load Note: The use of fewer than 4 inputs or outputs is possible. Any unused input ports have to be terminated with low-power 50-Ohm loads (e.g. Kathrein type 784 10367), unused output ports have to be terminated with high-power 50-Ohm loads (e.g. Kathrein low-intermodulation type 782 10474). 261 Active Duplex Hybrid Combiner (Same-Band Combiner) 880 ... 960 MHz EGSM 900 880 ... 960 MHz UMTS 900 • Enables antenna and feeder sharing for two base stations in the 900 MHz frequency band • 12 dB gain over 20 MHz Rx bandwidth (factory tunable) • Very low insertion loss over 20 MHz Tx bandwidth (factory tunable) compared to standard hybrid combiners • Double unit in one housing for XPol antennas • Suitable for indoor or outdoor applications • Supports AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard Port 1 Port 2 Port 4 Port 5 • By-pass mode (LNA) to ensure cell operation in case of DC power down • Built-in lightning protection RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Technical Data 782 11110 Type No. Pass band Rx Tx Tx Insertion loss Port 1 Port 3 / Port 4 Rx gain Isolation Port 1 Port 2 / Port 4 20 MHz within 880 ... 915 MHz (factory tunable) 20 MHz within 925 ... 960 MHz (factory tunable) Port 6 < 0.2 dB (925 – 945 MHz) – see Diagram I and II 12 dB ±0.5 dB Port 5 > 25 dB (880 – 900 MHz) > 35 dB (925 – 945 MHz) < 1.25 (880 – 900 / 925 – 945 MHz) 50 Ω Port 1: < 250 W Port 4: < 250 W < –160 dBc (5th / 7th order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) 3 kA, 10/350 μs pulse –40 … +65 °C IP67 > 1 000 000 hours (per TMA) According to ETS 300 342-3 10 – 30 V Nom. 195 mA at 10 V Nom. 85 mA at 30 V AISG 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 – 30 V DC, pin 7: DC return, other pins: not connected) With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Lightning protection Operating temperature range IP rating MTBF EMC DC supply Operating current per DTMA (without RET) Alarm management Connectors RF AISG Mounting 262 Port 3 Port 6 Active Duplex Hybrid Combiner (Same-Band Combiner) 880 ... 960 MHz EGSM 900 880 ... 960 MHz UMTS 900 Accessories (order separately) Clamp Set Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm Calculated Attenuation Curves 734 361 60 – 80 mm 734 362 80 – 100 mm Tuning example Rx: 880 – 900 MHz, Tx: 925 – 945 MHz 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 793 301 DC stop 784 10367 DC stop Diagram I Port 1 Port 4 Port 3 Port 6 Diagram II Port 1 Port 4 Port 3 Port 6 Diagram III Port 2 Port 5 Port 3 Port 6 Diagram IV Port 2 Port 5 Port 3 Port 6 50-Ω load 50-Ω load 1.5 W / indoor or outdoor Application example 263 Duplex Hybrid Combiner (Same-Band Combiner) 880 – 960 MHz GSM 900 880 – 960 MHz UMTS 900 • Enables antenna and feeder sharing for two base stations in the 900 MHz frequency band • Very low insertion loss over full EGSM/UMTS 900 Tx bandwith compared to standard hybrid combiners • Double unit in one housing for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply (for UMTS paths only) Port 3 Port 2 Port 6 Port 1 Port 4 Port 5 Typical Attenuation Curves Attenuation/dB Diagram I Port 1 Port 4 Port 3 Port 6 0 5 10 925 – 960 880 – 915 15 20 25 30 35 40 45 50 870 880 890 900 910 920 930 940 950 960 970 Frequency/MHz Attenuation/dB Diagram II Port 1 Port 4 Port 3 Port 6 0 0.5 1.0 925 – 960 880 – 915 1.5 2.0 2.5 3.0 Technical Data 3.5 4.0 782 10805 Type No. 880 – 915 MHz 925 – 960 MHz Port 6 < 0.4 dB, typically 0.2 dB (925 – 960 MHz) – see Diagram I and II < 4.3 dB, typically 3.6 dB (880 – 915 MHz) – see Diagram I and II Port 6 < 4.0 dB, typically 3.5 dB (880 – 915 MHz) – see Diagram III and IV Port 5 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 5 Port 6 Port 2 Port 3 / Port 4 Port 6 Lightning protection Mounting 264 890 900 910 920 930 940 950 960 970 Diagram III Port 2 Port 5 Port 3 Port 6 0 5 10 925 – 960 880 – 915 15 20 VSWR Impedance Input power Weight Packing size Dimensions (w x h x d) 880 Frequency/MHz Attenuation/dB Port 2 Port 3 / Port 5 Isolation Port 1 Port 2 / Port 4 5.0 870 > 25 dB (880 – 915 MHz) > 35 dB (925 – 960 MHz) < 1.2 (880 – 915 / 925 – 960 MHz) 50 Ω Port 1: < 250 W Port 4: < 250 W < –160 dBc (3 rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 6.5 kg 390 x 470 x 160 mm 287.1 x 278.6 x 71 mm (without connectors, without mounting brackets) 25 30 35 40 45 50 870 880 890 900 910 920 930 940 950 960 970 Frequency/MHz Diagram IV Attenuation/dB Pass band Rx Tx Insertion loss Port 1 Port 3 / Port 4 4.5 Port 2 Port 5 Port 3 Port 6 0 0.5 1.0 925 – 960 880 – 915 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 870 880 890 900 910 920 930 940 950 960 Frequency/MHz 970 Duplex Hybrid Combiner (Same-Band Combiner) 880 – 960 MHz GSM 900 880 – 960 MHz UMTS 900 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 793 301 784 10367 Clamp Set 782 10440 DC stop 50-Ω load DC stop 50-Ω load 1.5 W indoor or outdoor BTS UMTS900 BTS EGSM900 Application example 265 Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 UMTS 2100 (10 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Customized 10 MHz Tx/Rx bandpass filters (factory tunable) available for inserting a second UMTS 2100 base station • Full pass-band (without the second UMTS 2100 10 MHz Tx/Rx frequency blocks) available for the first UMTS 2100 base station • Low insertion loss over complete UMTS 2100 Tx/Rx bandwidth compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Port 2 Port 1 Port 6 Port 3 Port 4 Port 5 Block Diagram Tuning Examples 1 2 3 Technical Data 782 10925 Type No. Pass band BTS 1 (UMTS 2100) Rx = 1920 – 1980 / Tx = 2110 – 2170 MHz (without assigned BTS 2 10 MHz Tx/Rx frequency blocks and ±5 MHz guard bands) Rx = 1920 ... 1980 / Tx = 2110 ... 2170 MHz (factory tunable 10 MHz frequency blocks) 5 MHz (between Tx1/Rx1 and Tx3/Rx3, between Tx2/Rx2 and Tx4/Rx4 e.g. tuning example 1: Rx1 (Rx2) = 1920 – 1965 and Tx1 (Tx2) = 2110 – 2155 MHz Rx3 (Rx4) = 1970 – 1980 and Tx3 (Tx4) = 2160 – 2170 MHz BTS 2 (UMTS 2100) Guard band Insertion loss Port 1 Port 3 / Port 4 Port 2 Port 3 / Port 5 Isolation Port 1 Port 2 / Port 4 VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 4 Port 2 Port 3 / Port 5 Lightning protection Mounting Weight Dimensions (w x h x d) 266 Port 6 Port 6 < 1.2 dB – see diagram I and II for tuning example 1 < 1.2 dB – see diagram III and IV for tuning example 1 Port 5 > 30 dB (1920 – 1980 / 2110 – 2170 MHz) < 1.25 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) Port 6 Port 6 Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 6.5 kg 243 x 240 x 100 mm (without connectors, without mountain brackets) Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 UMTS 2100 (10 MHz Bandwidth) Accessories (order separately) BTS 2 (UMTS 2100) BTS 1 (UMTS 2100) Diagram I (Port 1 Port 3 / Port 4 Port 6) 0 Diagram III (Port 2 Attenuation/dB Clamp set suitable for mast diameter of Attenuation/dB Type No. Calculated Attenuation Curves (Tuning Example 1) 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm -20 -20 120 – 140 mm -25 -25 -30 -30 -35 -35 -40 -40 -45 -45 734 364 734 365 Type No. 784 10367 45 – 125 mm Description -5 -10 1920 – 1965 Rx 2110 – 2155 Tx -15 Port 6) -5 -10 -15 1970 – 1980 Rx 2160 – 2170 Tx -50 1900 1920 1940 1960 1980 2000 2020 2040 2060 2080 2100 2120 2140 2160 2180 2200 -50 1900 1920 1940 1960 1980 2000 2020 2040 2060 2080 2100 2120 2140 2160 2180 2200 50-Ohm load Port 3 / Port 5 0 Frequency/MHz Frequency/MHz Clamp Set 50-Ohm load Port 3 / Port 4 Port 6) 0 -0.5 -1.0 1920 – 1965 Rx 2110 – 2155 Tx -1.5 Diagram IV (Port 2 Attenuation/dB Attenuation/dB Diagram II (Port 1 0 1970 – 1980 Rx Port 3 / Port 5 Port 6) 2160 – 2170 Tx -0.5 -1.0 -1.5 -2.0 -2.0 -2.5 -2.5 -3.0 -3.0 -3.5 -3.5 -4.0 -4.0 -4.5 -4.5 -5.0 1900 1920 1940 1960 1980 2000 2020 2040 2060 2080 2100 2120 2140 2160 2180 2200 -5.0 1900 1920 1940 1960 1980 2000 2020 2040 2060 2080 2100 2120 2140 2160 2180 2200 Frequency/MHz Frequency/MHz 267 Same-Band Combiner 880 – 915 / 925 – 960 MHz 880 ... 915 / 925 ... 960 MHz GSM 900 LTE / UMTS 900 (5 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations within the same frequency band • Customized 5 MHz Tx/Rx pass-band filters (factory tunable) available for inserting LTE/UMTS 900 base station Port 1 Port 3 Port 2 • Full pass-band (without LTE/UMTS 900 5 MHz Tx/Rx frequency blocks) available for GSM 900 base station • Very low insertion loss over complete EGSM Tx/Rx bandwidth compared to standard hybrid combiners Port 4 Port 6 Port 5 • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Block Diagram Tuning Examples 1 2 3 Technical Data 782 10930 Type No. Pass band GSM 900 Rx = 880 – 915 / Tx = 925 – 960 MHz (without assigned LTE/UMTS 900 5 MHz TX/Rx frequency blocks and ± 3 MHz guard bands) Rx = 880 ... 915 / Tx = 925 ... 960 MHz (factory tunable 5 MHz frequency blocks) 3 MHz (between Tx/Rx1 and Tx/Rx3, between Tx/Rx2 and Tx/Rx4) – e.g. tuning example 1: Rx1 (Rx2) = 880 – 892 / 903 – 915 and Tx1 (Tx2) = 925 – 937 / 948 – 960 MHz Rx3 (Rx4) = 895 – 900 and Tx3 (Tx4) = 940 – 945 MHz LTE/UMTS 900 Guard band Insertion loss Port 1 Port 3 / Port 4 Port 2 Port 3 / Port 5 Isolation Port 1 Port 2 / Port 4 VSWR Group delay variation GSM 900 LTE/UMTS 900 Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 4 Port 2 Port 3 / Port 5 Lightning protection Mounting Dimensions (w x h x d) 268 Port 6 Port 6 < 0.5 dB (typically 0.1 dB) – see diagram I and II for tuning example 1 < 0.5 dB – see diagram III and IV for tuning example 1 Port 5 > 30 dB (880 – 915 / 925 – 960 MHz) < 1.25 (pass bands) < 20 ns (200 kHz) < 50 ns (5 MHz) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) Port 6 Port 6 Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 498 x 455 x 154.5 mm (without connectors, without mounting brackets) Same-Band Combiner 880 – 915 / 925 – 960 MHz 880 ... 915 / 925 ... 960 MHz GSM 900 LTE / UMTS 900 (5 MHz Bandwidth) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 784 10367 50-Ohm load Clamp Set 50-Ohm load Calculated Attenuation Curves (Tuning Example 1) BTS 1 (GSM 900) BTS 2 (LTE/UMTS 900) Diagram I (Port 1 Port 3 / Port 4 Port 6) Diagram III (Port 2 Port 3 / Port 5 Port 6) Diagram II (Port 1 Port 3 / Port 4 Port 6) Diagram IV (Port 2 Port 3 / Port 5 Port 6) 269 Same-Band Combiner 880 – 886 / 925 – 931 MHz 903 – 915 / 948 – 960 MHz GSM900 (6 MHz Bandwidth) GSM900 (12 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations Port 3 within the same frequency band • Very low Tx/Rx insertion loss compared to standard hybrid combiners Port 2 Port 6 Port 4 • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Port 5 Port 1 Block Diagram Tuning Diagram Technical Data 782 10935 Type No. Pass band BTS 1 (GSM900 / Operator 1) BTS 2 (GSM900 / Operator 2) Insertion loss Port 1 Port 3 / Port 4 Port Port 2 Port 3 / Port 5 Port Isolation Port 1 Port 2 / Port 4 Port VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 4 Port Port 2 Port 3 / Port 5 Port Lightning protection Mounting Weight Dimensions (w x h x d) 270 Rx1/Rx2 = 880 – 886 MHz, Tx1/Tx2 = 925 – 931 MHz Rx3/Rx4 = 903 – 915 MHz, Tx3/Tx4 = 948 – 960 MHz 6 6 < 0.4 dB (880 – 886 MHz) / < 0.6 dB (925 – 931 MHz) < 0.6 dB (903 – 915 MHz) / < 0.4 dB (948 – 960 MHz) 5 > 30 dB (880 – 886 / 903 – 915 / 925 – 931 / 948 – 960 MHz) < 1.2 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) 6 6 Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 6.9 kg 275 x 176 x 140 mm (without connectors, without mounting brackets) Same-Band Combiner 880 – 886 / 925 – 931 MHz 903 – 915 / 948 – 960 MHz GSM900 (6 MHz Bandwidth) GSM900 (12 MHz Bandwidth) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 784 10367 50-Ohm load Clamp Set 50-Ohm load Typical Attenuation Curves BTS 2 (GSM 900) BTS 1 (GSM 900) Diagram I (Port 1 Port 3 / Port 4 Port 6) Diagram III (Port 2 Port 3 / Port Diagram II (Port 1 Port 3 / Port 4 Port 6) Diagram IV (Port 2 Port 3 / Port 5 Port 6) Port 6) Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. These facts must be considered during the site planning process. The Same-band Combiner is designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas, filters, combiners, amplifiers and accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Terminate unused inputs with a suitable 50-Ohm load, e.g. 784 10367. Any previous datasheet issues have now become invalid. 271 Same-Band Combiner 880 – 890 / 925 – 935 MHz 902.5 – 915 / 947.5 – 960 MHz GSM900 (10 MHz Bandwidth) GSM900 (12.5 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations Port 3 within the same frequency band • Very low Tx/Rx insertion loss compared to standard hybrid combiners Port 2 Port 6 Port 4 • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Port 5 Port 1 Block Diagram Tuning Diagram Technical Data 782 10936 Type No. Pass band BTS 1 (GSM900 / Operator 1) BTS 2 (GSM900 / Operator 2) Insertion loss Port 1 Port 3 / Port 4 Port Port 2 Port 3 / Port 5 Port Isolation Port 1 Port 2 / Port 4 Port VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 4 Port Port 2 Port 3 / Port 5 Port Lightning protection Mounting Weight Dimensions (w x h x d) 272 Rx1/Rx2 = 880 – 890 MHz, Tx1/Tx2 = 925 – 935 MHz Rx3/Rx4 = 902.5 – 915 MHz, Tx3/Tx4 = 947.5 – 960 MHz 6 6 < 0.5 dB, typically 0.3 dB (880 – 890 MHz) / < 0.7 dB, typically 0.4 dB (925 – 935 MHz) < 0.7 dB, typically 0.5 dB (902.5 – 915 MHz) / < 0.5 dB, typically 0.3 dB (947.5 – 960 MHz) 5 > 30 dB (880 – 890 / 902.5 – 915 / 925 – 935 / 947.5 – 960 MHz) < 1.2 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) 6 6 Stop By-pass (max. 2500 mA) 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 6.9 kg 275 x 176 x 140 mm (without connectors, without mounting brackets) Same-Band Combiner 880 – 890 / 925 – 935 MHz 902.5 – 915 / 947.5 – 960 MHz GSM900 (10 MHz Bandwidth) GSM900 (12.5 MHz Bandwidth) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 784 10367 50-Ohm load Typical Attenuation Curves BTS 2 (GSM900) BTS 1 (GSM900) Diagram I (Port 1 Port 3 / Port 4 Port 6) Diagram III (Port 2 Port 3 / Port 5 Port 6) Diagram II (Port 1 Port 3 / Port 4 Port 6) Diagram IV (Port 2 Port 3 / Port 5 Port 6) Clamp Set 50-Ohm load 273 Hybrid Ring Junction (180° Hybrid) 806 – 960 MHz / 1710 – 1880 MHz The hybrid ring junction can be used: – as a power splitter with a ratio of 1:1, – for the decoupled combining of two transmitters with arbitrarily low frequency spacing ( at 3 dB loss), – for the decoupled combining of two receivers with arbitrarily low frequency spacing, – for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, – as component to form combiners. Port 1 Port 2 Port 3 Port 4 K 63 73 621 790 881 Description: The hybrid ring junction has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 4, port 3 is decoupled and without power if ports 2 and 4 are ideally matched. In practice an absorber of suitable power at port 3 is to be planned for according to the mismatch of ports 2 and 4. Decoupled combining can be made via ports 1 and 3 or 2 and 4. Port 4 Port 1 Port 3 2 λ/4 Port 2 791 498 λ/4 1 3 λ/4 3/4λ 4 Technical Data K 63 73 621 Type No. Frequency range Attenuation 1 2 or 1 Attenuation 1 VSWR Impedance Input power Connectors Application Mounting 3 or 2 Weight Packing size Dimensions (w x h x d) 4 4 790 881 806 – 960 MHz 890 – 960 MHz 3 ±0.4 dB 3 ±0.3 dB (see diagram I) (see diagram I) See diagram II < 1.2 50 Ω < 100 W per input N female Indoor With 2 screws (max. 4.5 mm diameter) 0.32 kg Approx. 160 x 40 x 105 mm 150 x 30 x 87 mm (including connectors) 791 498 1710 – 1880 MHz 3 ±0.4 dB (see diagram I) See diagram II < 1.3 50 Ω < 50 W per input N female Indoor With 4 screws (max. 4.5 mm diameter) 0.25 kg 90 x 40 x 110 mm 80 x 26 x 106 mm (including connectors) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 274 Hybrid Ring Junction (180° Hybrid) 806 – 960 MHz / 1710 – 1880 MHz Typical Attenuation Curves K 63 73 621 44 // dB Typical attenuation 1 vs. frequency 2 and 1 Diagram II 4 Attenuation 1 3 or 2 4 vs. frequency 20 2.5 960 Frequency/MHz dB 33/ /dB 806 dB 44/ /dB 11 22 3.5 Attenuation 2 2 Attenuation 11 44 3.0 Attenuation 11 Attenuation Attenuation 11 Attenuation 11 Attenuation 22 // dB Diagram I 30 40 806 820 860 900 940 960 Frequency/MHz typical attenuation guaranteed attenuation 790 881 Typical attenuation 1 vs. frequency 2 and 1 Diagram II 4 Attenuation 1 3 or 2 4 vs. frequency 20 2.5 11 44 890 960 Frequency/MHz 4 / dB 11 22 3.5 30 Attenuation22 Attenuation 3.0 Attenuation1 1 33 // dB Attenuation Attenuation Attenuation1 1 44/ /dB Attenuation1 1 22/ /dB Attenuation Diagram I 40 890 910 930 950 960 Frequency/MHz typical attenuation guaranteed attenuation 791 498 44 / dB Typical attenuation 1 vs. frequency 2 and 1 Diagram II 4 Attenuation 1 3 or 2 4 vs. frequency 20 2.5 11 44 11 22 1880 Frequency/MHz dB 44 // dB 1710 3 / dB 3.5 30 Attenuation Attenuation22 3.0 Attenuation Attenuation11 Attenuation Attenuation 11 Attenuation Attenuation 11 2 / dB Diagram I 40 1700 1750 1800 1850 Frequency/MHz 1900 typical attenuation guaranteed attenuation 275 3-dB Coupler Hybrid Combiner 2 : 2 698 – 2690 MHz • Can be used for the decoupled combining of 2 transmitters Port 1 onto a common antenna with frequency spacing as narrow as desired (3 dB loss) – see application example 1 • Can be used for the decoupled combining of 2 transmitters Port 3 onto two antennas with frequency spacing as narrow as desired – see application example 2 • Can be used as a decoupled 2-way splitter – see application example 3 Port 2 • Can be used as a frequency-independant 90° phase shifter (90° Hybrid) Port 4 • Suitable for indoor or outdoor applications • DC/AISG by-pass • External DC stop available as an accessory Diagram Technical Data Type No. 782 10524 Frequency range Attenuation Port 1 Port 2 Port 1 Port 3 Port 2 Port 3 Directivity VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency 698 – 2690 MHz Mounting Weight Packing size Dimensions (w x h x d) 3.1 ±0.5 dB 3.1 ±0.5 dB See diagram > 20 dB < 1.25 50 Ω < 150 W at each input port < –160 dBc (3 rd order; with 2 x 20 W) –40 ... +70 °C 7-16 female Indoor or outdoor (IP66) By-pass between Port 1 Port 3 / Port 2 Port 4 (max. 2500 mA) External DC stop available as an accessory With 4 screws (max. 6.5 mm diameter) 1.5 kg 268 x 115 x 203 mm 205.4 x 60 x 104 mm (without connectors and mounting feet) Note: VSWR and attenuation values only valid if all ports are terminated with 50-Ohm loads. 276 Attenuation Port 2 ↔ Port 3 / dB Typical attenuation Port 2 ↔ Port 3 vs. VSWR at Port 1 25 20 15 1.0 1.5 2.0 VSWR at Port 1 (with 50-Ohm load at Port 4) Accessories (order separately) Type No. Description 782 10850 DC stop 782 10474 50-Ohm load (80 W) 784 10367 50-Ohm load (1.5 W) DC stop 50-Ohm load 50-Ohm load 3-dB Coupler Hybrid Combiner 2 : 2 698 – 2690 MHz 277 3-dB Coupler (90° Hybrid) 806 – 960 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1:1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a component to form combiners. earth screw M6 Attenuation / / dB Attenuation 11 3 3 Diagram I Attenuation Attenuation 11 2 /2 / dB Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned in accordance with the mismatch of ports 2 and 3. Decoupled combining can be achieved via the diagonally opposite ports 2 and 3 or 1 and 4. Typical attenuation between ports 1 2 resp. 1 3 vs. frequency 2.5 1 1 22 3.0 1 33 3.5 coupler 7-16 806 960 Frequency/MHz 1 3 2 4 Technical Data Intermodulation products Temperature range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 3 806 – 960 MHz 3 ±0.4 dB (see diagram I) See diagram II > 30 dB < 1.1 50 Ω < 500 W total power at two inputs, with max. 350 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 ... +70 °C 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 6 mm diameter) 1.8 kg 160 x 95 x 65 mm 136 x 46.5 x 94 mm (including connectors) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 278 Typical attenuation 2 Attenuation22 3 3/ dB / dB Attenuation Frequency range Attenuation 1 2/1 Attenuation 2 3 Directivity VSWR Impedance Input power Diagram II 793 506 Type No. 3 vs. VSWR at port 1 25 20 15 1.0 1.5 2.0 VSWR at port 1 (with 50-Ω load at port 4) 3-dB Coupler (90° Hybrid) 1700 – 2200 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1:1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a component to form combiners. Diagram I Attenuation 1 1 33 // dB Attenuation dB earth screw M6 Attenuation 1 1 22 // dB dB Attenuation Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned in accordance with the mismatch of ports 2 and 3. Decoupled combining can be achieved via the diagonally opposite ports 2 and 3 or 1 and 4. Typical attenuation between ports 11 2 resp. 1 13 vs.3frequency 2 resp. vs. frequency 2.5 11 22 3.0 11 33 3.5 coupler 7-16 1700 2200 Frequency/MHz 1 3 2 4 Technical Data Intermodulation products Temperature range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 3 1700 – 2200 MHz 3 ±0.4 dB (see diagram I) See diagram II > 25 dB < 1.15 50 Ω < 300 W total power at two inputs, with max. 200 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 ... +70 °C 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 5.5 mm diameter) 1.3 kg 160 x 95 x 65 mm 94 x 59.5 x 89 mm (including connectors) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. Typical attenuation 2 Attenuation Attenuation22 3 3/ dB / dB Frequency range Attenuation 1 2/1 Attenuation 2 3 Directivity VSWR Impedance Input power Diagram II 793 006 Type No. 3 vs. VSWR at port 1 25 20 15 1.0 1.5 2.0 VSWR at port 1 (with 50-Ω load at port 4) 279 3-dB Coupler (90° Hybrid) 800 – 2200 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1 : 1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a combiner component. Diagram I Attenuation Attenuation11 33/ / dB earth screw M6 Attenuation Attenuation11 22/ / dB Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into the ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned for according to the mismatch of ports 2 and 3. Decoupled combining can be achived via the diagonally opposite ports 2 and 3 respectively 1 and 4. Typical attenuation between ports 1 2 resp. 1 3 vs. frequency 1 22 2.0 3.0 4.0 1 33 coupler 7-16 800 2200 Frequency/MHz 1 3 2 4 Technical Data 3 Intermodulation products Temperatur range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 800 – 2200 MHz 3 ±1.2 dB (see diagram I) See diagram II > 20 dB < 1.2 50 Ω < 300 W total power at two inputs, with max. 200 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 … +70 °C 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 5.5 mm diameter) 1.3 kg 160 x 95 x 65 mm 104.9 x 50.2 x 93.9 mm (including connectors) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 280 Typical attenuation 2 AttenuationAttenuation Port 2 ↔ Port dB 2 33 // dB Frequency range Attenuation 1 2/ Attenuation 2 3 Directivity VSWR Impedance Input power Diagram II 793 554 Type No. 3 vs. VSWR at port 1 25 20 15 1.0 1.5 2.0 VSWR at Port VSWR at Port 11 (with 50-Ohm at Port 4) at Port 4) (with load 50-Ohm load System Components System Components Bias Tees Measuring Directional Couplers DC-Stops Attenuators 50-Ω Loads Power Distribution Unit 281 Summary of System Component Types System Components: Description Type No. DC Stop DC Stop Bias Tee Bias Tee AISG Bias Tee AISG/Bulkhead Bias Tee, outdoor Bias Tee, outdoor (AISG) Smart Bias Tee 12 V / BTS Smart Bias Tee 12 V / Antenna Smart Bias Tee 24 V / BTS Smart Bias Tee 24 V / Antenna Smart Bias Tee 12 V / BTS Smart Bias Tee 12 V / Antenna Smart Bias Tee 24 V / BTS Smart Bias Tee 24 V / Antenna Smart Bias Tee Smart Bias Tee 50-Ω Load (N male) 50-Ω Load (7-16 male) 50-Ω Load (7-16 female) 50-Ω Load (N male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) 50-Ω Load (7-16 male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) 50-Ω Load (7-16 male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) 50-Ω Load (7-16 female) Low IM Attenuator 3 dB Attenuator 6 dB Attenuator 10 dB Attenuator 20 dB Attenuator 3 dB Attenuator 6 dB Attenuator 10 dB Attenuator 20 dB 793 301 782 10850 793 304 782 10429 782 10550 782 10577 782 10578 782 10253 782 10254 782 10255 782 10256 782 10453 782 10454 782 10455 782 10456 782 11055 782 11056 K 62 26 61 1 784 10367 784 10470 K 62 26 11 1 K 62 26 40 1 K 62 26 41 1 K 62 26 20 1 K 62 26 21 1 K 62 26 20 7 K 62 26 21 7 K 62 26 30 1 K 62 26 31 1 K 62 26 30 7 K 62 26 31 7 K 62 26 50 1 K 62 26 51 1 K 62 26 50 7 782 10474 784 10235 784 10236 784 10237 784 10238 791 918 791 919 791 920 791 921 Measuring Directional Coupler 792 972 Description Power Distribution Unit (PDU) Type No. 782 10344 New Products 282 Frequency range Max. input power Page 750 750 250 250 250 250 250 750 750 750 750 750 750 750 750 750 750 0.5 1.5 1.5 2 10 10 25 25 25 25 50 50 50 50 100 100 100 80 2 2 2 2 15 12 10 10 283 284 285 286 287 288 289 290, 291 290, 291 290, 291 290, 291 290, 291 290, 291 290, 291 290, 291 292, 293 292, 293 296 296 296 296 296 296 297 297 297 297 297 297 297 297 297 297 297 298 299 299 299 299 299 299 299 299 800 – 2170 MHz 250 – 2700 MHz 800 – 2170 MHz 800 – 2170 MHz 1710 – 2170 MHz 690 – 2700 MHZ 690 – 2700 MHZ 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 800 – 2170 MHz 690 – 2700 MHz 690 – 2700 MHz 0 – 2700 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 1000 MHz 0 – 1000 MHz 0 – 1000 MHz 800 – 2700 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 824 – 960 MHz 960 – 2500 MHz W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W 800 W 200 W 300 Power supply (DC input) Page 38 ... 72 V DC 294, 295 DC Stop 800 – 2170 MHz DC Stop is used in dual- or multi-band antenna systems where one or more antenna systems require a DC supply for an installed mast head amplifier. The DC Stop prevents DC voltage from being shorted within the non-biased antenna system(s) and isolates the corresponding base station output(s) from DC voltage. • Low RF signal insertion loss • High DC signal isolation from port 1 to port 2 and vice versa • Suitable for indoor or outdoor applications 70.4 39.5 M29x1.5 793 301 DC - Stop 800–2170 MHz 32 Application Example Technical Data Type No. Frequency range Insertion loss Port 1 Port 2 Isolation Port 1 Port 2 VSWR Impedance Input power Intermodulation products Temperature range Connectors Port 1 Port 2 Application Weight Dimensions (w x h x d) 793 301 Port 2 800 – 2170 MHz < 0.1 dB (800 – 2170 MHz) Port 1 > 70 dB (DC) < 1.1 ( 800 – 2000 MHz) < 1.2 (2000 – 2170 MHz 50 Ω < 750 W (800 – 2170 MHz) < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 male 7-16 female Indoor or outdoor (IP 67) 0.32 kg 70.4 mm x 39.5 mm x 32 mm (including connectors and earthing screw of 6 mm diameter) 283 DC Stop 250 – 2700 MHz DC Stop is used in dual- or multi-band antenna systems where one or more antenna systems require a DC supply for an installed mast head amplifier. The DC Stop prevents DC voltage from being shorted within the non-biased antenna system(s) and isolates the corresponding base station output(s) from DC voltage. • Low RF signal insertion loss • High DC signal isolation from port 1 to port 2 and vice versa • Suitable for indoor or outdoor applications 78210850 78210555 78210850 2 x 78210660 (single unit) or 2 x 78210661 (double unit) 70.4 78210850 DC - Stop 250–2700 MHz Port 1 39.5 M29x1.5 32 Port 2 2 x 78210660 (single unit) or 2 x 78210661 (double unit) 78210850 78210850 Application Example Technical Data Type No. 782 10850 Frequency range Insertion loss Port 1 Port 2 Isolation Port 1 Port 2 VSWR 250 – 2700 MHz Impedance Input power Intermodulation products Temperature range Connectors Port 1 Port 2 Application Weight Dimensions (w x h x d) 284 < 0.1 dB (250 – 2700 MHz) > 70 dB (DC) < 1.1 (380 – 2700 MHz) < 1.2 (250 – 380 MHz) 50 Ω < 750 W (250 – 2700 MHz) < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 male 7-16 female Indoor or outdoor (IP 67) 0.32 kg 70.4 mm x 39.5 mm x 32 mm (including connectors and earthing screw of 6 mm diameter) Port 2 Port 1 Bias Tee 800 – 2170 MHz The Bias Tee is suitable to feed DC voltage into the feeder cable of a receiving and/or transmitting antenna system in order to provide the operating voltage for a mast head amplifier. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. 16 35.4 793 304 Bias Tee 800–2170 MHz Antenna BTS DC DC 6.5 6.5 28.5 47 88 Application Example Technical Data Type No. Frequency range Insertion loss BTS Antenna Isolation BTS Antenna BTS DC VSWR Impedance Input power BTS DC Intermodulation products Lightning protection Temperature range Connectors BTS Antenna Port DC Application Weight Packing size Dimensions (w x h x d) 793 304 Antenna 800 – 2170 MHz < 0.1 dB (800 – 2170 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (800 – 2170 MHz) 50 Ω BTS Port DC < 250 W (800 – 2170 MHz) < 1000 mA / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 5 kA, 8/20 μs pulse –40 ... +70 °C 7-16 male 7-16 female SMB male Indoor 0.6 kg 145 x 145 x 50 mm 88 x 47 x 35.4 mm (including connectors and earthing screw of 6 mm diameter) 285 Bias Tee 800 – 2170 MHz The Bias Tee is suitable to feed DC voltage and AISG control signals into the feeder cable in order to provide operating voltage and control signals via the RF feeder cable to the TMA or RCU. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage and AISG control signal (2.176 MHz) is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken in conjunction with the CCU-LOC to protect against static discharge and lightning ensure a high level of reliability and operational safety. 16 35.4 793 304 Bias Tee Bias Tee 800–2170 MHz 800–2170 MHz Antenna BTS Antenna BTS DC DC/AISG DC 6.5 6.5 28.5 47 88 Application Example Technical Data Type No. 782 10429 Frequency range Insertion loss BTS Antenna Isolation BTS Antenna BTS DC/AISG VSWR Impedance Input power BTS DC/AISG 800 – 2170 MHz Lightning protection Intermodulation products Temperature range Connectors Port 1 BTS Port 2 Antenna Port DC/AISG Application Weight Packing size Dimensions (w x h x d) 286 Port 2 Feeder < 0.1 dB (800 – 2170 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (800 – 2170 MHz) 50 Ω < 250 W (800 – 2170 MHz) < 1.8 A / 13 VDC < 0.8 A / 29 VDC 3 kA, 10/350 μs pulse < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 male 7-16 female SMB male Indoor 0.6 kg 145 x 145 x 50 mm 88 x 47 x 35.4 mm (including connectors and earthing screw of 6 mm diameter) Port 1 BTS Port DC/AISG Bias Tee 1710 – 2170 MHz The Bias Tee is suitable to feed DC voltage and AISG control signals into the feeder cable in order to provide operating voltage and control signals via the RF feeder cable to the TMA or RCU. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage and AISG control signal (2.176 MHz) is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken in conjunction with the CCU-LOC to protect against static discharge and lightning ensure a high level of reliability and operational safety • Designed for front panel mounting (Bulkhead version). outdoor indoor Front panel (bulkhead) Application Example Technical Data Type No. Frequency range Insertion loss BTS Antenna Isolation BTS Antenna BTS DC/AISG VSWR Impedance Input power BTS DC/AISG Lightning protection Intermodulation products Temperature range Connectors Port 1 BTS Port 2 Antenna Port DC/AISG Application Weight Packing size Dimensions (w x h x d) 782 10550 Port 1 BTS 1710 – 2170 MHz < 0.1 dB (1710 – 2170 MHz) Port 2 Feeder > 70 dB (DC) > 70 dB (DC) < 1.1 (1710 – 2170 MHz) 50 Ω < 250 W (1710 – 2170 MHz) < 1.8 A / 13 VDC < 0.8 A / 29 VDC 3 kA, 10/350 μs pulse; 20 kA, 8/20 μs pulse < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 female 7-16 female SMB male Indoor, port 2 connector outdoor with sealing (O-ring) 0.6 kg 145 x 145 x 50 mm 91 x 47 x 35.4 mm (including connectors) 287 Bias Tee 690 – 2700 MHz The Bias Tee is suitable to feed DC voltage into the feeder ca-ble of a receiving and/or transmitting antenna system in order to provide the operating voltage for a mast head amplifier. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken to protect against static discharge and lightning ensure 936.3769 Subject to alteration. a high level of reliability and operational safety. Application Example Technical Data Port DC Type No. 782 10577 Frequency range Insertion loss Port 1 Port 2 Isolation Port 1 Port 2 Port 1 DC VSWR Impedance Input power Port 1 DC Intermodulation products Lightning protection Temperature range Connectors Port 1 (BTS) Port 2 (Antenna) Port DC Application Weight Packing size Dimensions (w x h x d) 690 – 2700 MHz 288 Port 2 Antenna < 0.1 dB (690 – 2700 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (690 – 2700 MHz) 50 Ω < 250 W (690 – 2700 MHz) < 1 A / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 3 kA, 10/350 μs pulse –40 ... +70 °C 7-16 male 7-16 female SMA female Indoor or outdoor (IP 66) 0.47 kg 128 x 75 x 88 mm 85.4 x 45 x 46.2 mm (including connectors and earthing screw of 6 mm diameter) Port 1 BTS Bias Tee (AISG) 690 – 2700 MHz The Bias Tee is suitable to feed DC voltage and AISG control signals into the feeder cable in order to provide operating voltage and control signals via the RF feeder cable to the TMA or RCU. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage and AISG control signal (2.176 MHz) is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken in conjunction with the CCU-LOC to protect against 936.3771 Subject to alteration. static discharge and lightning ensure a high level of reliability and operational safety. Application Example Technical Data Type No. 782 10578 Frequency range Insertion loss Port 1 Port 2 Isolation Port 1 Port 2 Port 1 Port DC/AISG VSWR Impedance Input power Port 1 Port DC/AISG Intermodulation products Lightning protection Temperature range Connectors Port 1 (BTS) Port 2 (Antenna) Port DC/AISG Application Weight Packing size Dimensions (w x h x d) 690 – 2700 MHz Port DC/AISG Port 2 Antenna < 0.1 dB (690 – 2700 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (690 – 2700 MHz) 50 Ω < 250 W (690 – 2700 MHz) < 1 A / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 3 kA, 10/350 μs pulse –40 ... +70 °C Port 1 BTS 7-16 male 7-16 female SMA female Indoor or outdoor (IP 66) 0.47 kg 128 x 75 x 88 mm 85.4 x 45 x 46.2 mm (including connectors and earthing screw of 6 mm diameter) 289 Smart Bias Tee 800 – 2170 MHz The Smart Bias Tee combines the performance of a standard Bias Tee (e.g. type 793 304) with the function of an additional modem (AISG standard) in order to provide either DC voltage as well as remote control signals via an RF feeder cable to a TMA or RCU. The Smart Bias Tee provides low RF signal insertion loss from port 1 to port 2 and vice versa.The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. • 782 10253, 782 10453: 12 V version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable Port 1 Antenna Port 2 Feeder Port 1 Antenna Port DC/RCU 782 10254 782 10256 • 782 10254, 782 10454: 12 V version for use near the antenna, in order to control an RCU (only required if no TMA is in use) Port 2 Feeder Port DC/RCU Port 1 BTS Port 2 Feeder 782 10454 782 10456 Port 2 Feeder Port 1 BTS • 782 10255, 782 10455: 24 V version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable • 782 10256, 78210456: 24 V version for use near the Port DC/RCU antenna, in order to control an RCU (only required if no TMA is in use) 782 10253 782 10255 Port DC/RCU 782 10453 782 10455 Pin connections Abbreviations: RCU = Remote Control Unit for remote electrical control of antenna tilt BTS = Base Transceiver Station TMA = Tower Mounted Amplifier AISG= Antenna Interface Standards Group Port 1 = Port for BTS or for Antenna Port 2 = Port for Feeder Cable Port DC/RCU = Port for DC voltage and remote control unit signals Technical Data Type No. Port 1: 7-16 male Port 2: 7-16 female Type No. Port 1: 7-16 female Port 2: 7-16 male Frequency range Insertion loss Port 1 Port 2 Isolation for DC and RCU signals Port 1 Port 2 Port 1 Port DC/RCU Port 2 Port DC/RCU VSWR Impedance Input power Port 1 or port 2 Port DC/RCU Power consumption Lightning protection Intermodulation products Temperature range Modem carrier frequency Application Weight Packing size Dimensions (w x h x d) 290 782 10253 782 10254 782 10255 782 10256 12 V / BTS 12 V / Antenna 24 V / BTS 24 V / Antenna BTS Feeder Antenna Feeder BTS Feeder Antenna Feeder 782 10453 782 10454 782 10455 782 10456 12 V / BTS 12 V / Antenna 24 V / BTS 24 V / Antenna BTS Feeder Antenna Feeder BTS Feeder Antenna Feeder 800 – 2170 MHz < 0.1 dB (800 – 2170 MHz) > 70 dB > 70 dB > 0 dB < 1.1 (800 – 2170 MHz) 50 Ω < 750 W (800 – 2170 MHz) < 2.5 A / +8 … +14 VDC < 750 W (800 – 2170 MHz) < 2.5 A / +8 … +30 VDC Typically 0.6 W 3 kA, 10/350 μs pulse < –160 dBc (3rd order; with 2 x 20 W) –40 ... +60 °C 2.176 MHz Indoor or outdoor (IP66) 1.5 kg 167 x 102 x 86 mm 79 x 79 x 43.5 mm (without connectors) Smart Bias Tee 800 – 2170 MHz Block diagrams Application Examples Port 1 (Antenna) Warning: Don’t mix 12 V and 24 V Bias Tees in any configuration. Always choose corresponding voltage to suit the TMA. Port 2 (Feeder) Port 2 (Feeder) Port DC/RCU (RCU) Port DC/RCU (CCU) Port 1 (BTS) Port 1 (Antenna) Antenna system (1 sector) without TMA Antenna system (1 sector) with Kathrein TMA Port DC/RCU (RCU) Please note: The Smart Bias Tees are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. Port 2 (Feeder) The installation team must be properly qualified and also be familiar with the relevant national safety regulations. Port 2 (Feeder) The coupling torque at 7-16 connectors is 25 – 30 Nm! Hold the smart bias tee housing securely while tightening the 7-16 locking nut. The tightning torque for fixing the AISG connector must be 0.5 – 1.0 Nm (‘hand-tightened’). Port 1 (BTS) Port DC/RCU (CCU) Antenna system (1 sector) without TMA Antenna system (1 sector) with Kathrein TMA Dimensional Drawings 782 10253, 782 10255 782 10453, 782 10455 782 10254, 782 10256 782 10454, 782 10456 291 Smart Bias Tee 690 – 2700 MHz • The Smart Bias Tee combines the performance of a standard Bias Tee (e.g. type 793 304) with the function of an additional modem (AISG standard) in order to provide either DC voltage as well as remote control signals via an RF feeder cable to a TMA or RCU. • The Smart Bias Tee provides low RF signal insertion loss from port 1 to port 2 and vice versa. The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. • 782 11055: +8 ... +30 V DC version (DC on pin 6) for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable Port 1 Antenna Port 2 Feeder • 782 11056: +8 ... +30 V DC version (DC on pin 6) for use near the antenna, in order to control an RCU (only required if no TMA is in use) RCU = Remote Control Unit for remote electrical control of antenna tilt BTS = Base Transceiver Station TMA = Tower Mounted Amplifier AISG = Antenna Interface Standards Group Port 1 = Port for BTS or for Antenna Port 2 = Port for Feeder Cable Port DC/RCU = Port for DC voltage and remote control unit signals Port DC/RCU 782 11056 Port 1 BTS Port 2 Feeder Port DC/RCU 782 11055 Technical Data Type No. Port 1: 7-16 male Port 2: 7-16 female Frequency range Insertion loss Port 1 Port 2 Isolation for DC and RCU signals Port 1 Port 2 Port 1 Port DC/RCU Port 2 Port DC/RCU VSWR Impedance Input power Port 1 or port 2 Port DC/RCU Power consumption Lightning protection Intermodulation products Temperature range Modem carrier frequency Application Weight Packing size Dimensions (w x h x d) 292 782 11055 782 11056 BTS Antenna BTS Feeder Antenna Feeder 690 – 2700 MHz < 0.1 dB (690 – 2700 MHz) > 70 dB > 70 dB > 0 dB < 1.1 (690 – 2700 MHz) 50 Ω < 750 W (690 – 2700 MHz) < 2.5 A / +8 … +30 VDC Typically 0.6 W 3 kA, 10/350 μs pulse < –160 dBc (3rd order; with 2 x 20 W) –40 ... +60 °C 2.176 MHz Indoor or outdoor (IP66) 0.8 kg 167 x 102 x 86 mm 81 x 81 x 46 mm (without connectors) Pin Connections Smart Bias Tee 690 – 2700 MHz Block Diagrams Application Examples Port 1 (Antenna) 782 11056 Port 2 (Feeder) Port DC/RCU (RCU) Port 2 (Feeder) Port DC/RCU (CCU) DC cable DC cable 782 11055 Antenna system (1 sector) without TMA Port 1 (BTS) Antenna system (1 sector) with Kathrein TMA Dimensional Drawings 782 11055 Please note: The Smart Bias Tees are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. 782 11056 The coupling torque at 7-16 connectors is 25 – 30 Nm! Hold the smart bias tee housing securely while tightening the 7-16 locking nut. The tightning torque for fixing the AISG connector must be 0.5 – 1.0 Nm (‘hand-tightened’). 293 Power Distribution Unit (PDU) The PDU provides DC supply voltage and alarm interfacing for up to 6 TMAs / MHAs (Tower Mounted Amplifiers / Mast Head Amplifiers) with current window alarming. • Suitable for low DC power requirements, e.g. Kathrein DTMA 782 10301 (UMTS) or 782 10312 (GSM1800) Input Power supply • Alarm signals available on SubD 9-pin connector Outputs Alarms Orange alarm LED Power supply failure and LEDs • Bias Tees and cable sets for connection of up to 6 Outputs DC supply voltage MHA1 ... MHA6 and Red alarm LEDs TMA failure DIP switch MHA1 ... MHA6 disconnect Bias Tees for servicing 6 TMAs (or 3 DTMAs = double TMAs) are available as accessories Alarm interface function: Under normal operating conditions each TMA pulls the nominal current from the PDU. In case of failure when a TMA consumes a current outside the specified alarm window, then an internal TMA circuit pulls an increased alarm current. Once the respective TMA failure detection threshold is registered by the PDU, then the following alarms are activated: 1. The DC supply voltage for the defective TMA is switched off. 2. The corresponding red alarm LED lights up. 3. The contacts 4 and 5 on the SubD 9-pin connector are closed. In addition, the respective pins 1 (TMA1), 2 (TMA2), 3 (TMA3), 6 (TMA4), 7 (TMA5), or 8 (TMA6) are grounded. This contact status can be used for monitoring purposes. If required, the additional DIP switch can be used to override the individual alarm and turn off the respective TMA supply voltage (1 = supply voltage and red LED alarm OFF, 0 = supply voltage and red LED alarm ON). Technical Data 782 10344 Type No. Power supply (DC input) DC supply voltage (DC outputs to MHA1 ... MHA6) Failure detection threshold Alarms LED indicators SubD 9-pin connector Electrical protection against Temperature range Connectors Scope of delivery MTBF Mounting Application Weight Dimensions (w x h x d) 38 ... 72 V DC 6x +12 ±0.3 V / nominal current: 110 mA ±20% > 230 mA ±10% Red LED ON = TMA failure at indicated DC output Orange LED ON = power supply failure (back-up power supply in use), Green LED ON = power supply ON Contact pins 4 + 5 closed when failure detection threshold is exceeded = MHA or power supply failure Contact pins 1 ... 3, 6 ... 8 grounded when failure detection threshold is exceeded = MHA failure Reverse voltage on DC outputs Reverse polarity voltage, over-current and over-voltage on DC input (power supply) –40 ... +60 °C Power supply: DIN 3-pin male DC supply voltage: BNC female (6x) Alarms: SubD 9-pin PDU, 3 m power supply cable with DIN 3-pin female connector, (brown (+), blue (–), green-yellow (grd) > 450 000 hours With 2 screws (M6) Indoor (IP20) 2.2 kg 19 ˝ drawer, 2 height units, plug-in depth 171 mm Accessories (order separately) Type No. Description Technical data 782 10388 Cable set 2 m (6 cables) 782 10389 Cable set 5 m (6 cables) Lenth: 2.0 m Cable type: RG 316 Connectors: BNC male / SMB female Voltage drop at 110 mA nominal current: < 0.2 V Lenth: 5.0 m Cable type: RG 316 Connectors: BNC male / SMB female Voltage drop at 110 mA nominal current: < 0.2 V Please see separate data sheet 793 304 Bias Tee Cable Set 782 10388 Bias Tee 793 304 294 Power Distribution Unit (PDU) Detail Power supply connector Application example Antenna system (1 sector) with Kathrein PDU 782 10344, Bias Tees 793 304 and UMTS Douple TMA 782 10301 Detail SupD 9-pin connector SubD 9-pin connector and LED alarms SubD 9-pin connector pin # MHA1 MHA2 MHA3 MHA4 MHA5 MHA6 Power supply failure no failure 4 5 Orange alarm LED Red alarm LED # Green alarm LED 1 2 3 6 7 8 9 1 2 3 4 5 grd – – – – – grd ON – – – – – – ON open – – – – – grd OFF – – – – – – ON – – – grd – ON – – – – – ON – – – grd – OFF – – – – – ON – – – grd – – ON – – – – ON failure – grd – no failure – open – failure – – grd no failure – – open – – – grd – – OFF – – – – ON failure – – – grd – – grd – – – ON – – – ON no failure – – – open – – grd – – – OFF – – – ON failure – – – no failure – – – failure – – no failure – failure no failure contacts closed if at least 1 failure 6 contacts open if no failure – grd – grd – – – – ON – – ON – open – grd – – – – OFF – – ON – – – grd grd – – – – – ON – ON – – – – open grd – – – – – OFF – ON – – – – – – grd – – – – – – ON ON – – – – – – grd – – – – – – OFF ON – contact status not defined grd contact grounded 295 50-Ohm Load 0 ... 4000 MHz 0.5 ... 100 W • Standard 50-Ohm terminations for small and medium power • Suitable for terminating open ports on RF equipment for indoor and/or outdoor applications 0.5 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz VSWR1000 – 2000 MHz VSWR2000 – 2700 MHz Application Weight Packing size Dimensions K 62 26 61 1 N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor 40 g 90 x 60 x 25 mm 33 / 21 mm diameter K 62 26 61 1 1.5 Watt * Type No. Connector Frequency range VSWR 0 – 2000 MHz VSWR 2000 – 4000 MHz Application Weight Packing size Dimensions 784 10367 784 10470 7-16 male 7-16 female 0 – 4000 MHz < 1.10 < 1.30 Indoor or outdoor (IP65) 120 g Approx. 50 x 90 x 100 mm 40 / 32 mm diameter 42 / 29 mm diameter 784 10367 2 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz VSWR 1000 – 2000 MHz VSWR 2000 – 2700 MHz Application Weight Packing size Dimensions K 62 26 11 1 N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor 40 g 90 x 60 x 25 mm 30 / 21 mm diameter K 62 26 11 1 10 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz V 1000 – 2000 MHz VSW R2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) 296 K 62 26 40 1 K 62 26 41 1 N female N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 250 g 50 x 90 x 100 mm 40 x 82 x 77 mm 40 x 82 x 85 mm (including connector) (including connector) K 62 26 40 1 50-Ohm Load 0 ... 4000 MHz 0.5 ... 100 W 25 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz VSWR1000 – 2000 MHz VSWR2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) K 62 26 20 1 K 62 26 21 1 N female N male K 62 26 20 7 K 62 26 21 7 35 x 94 x 113 mm (incl. connector) 7-16 female 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 0.5 kg 50 x 100 x 135 mm 35 x 94 x 121 mm 35 x 94 x 125 mm (incl. connector) (incl. connector) 7-16 male 35 x 94 x 124 mm (incl. connector) K 62 26 30 1 K 62 26 31 1 K 62 26 31 7 N female N male K 62 26 20 1 50 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz VSWR1000 – 2000 MHz VSWR2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) 67 x 90 x 130 mm (incl. connector) K 62 26 30 7 7-16 female 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 0.8 kg 80 x 95 x 145 mm 67 x 90 x 138 mm 67 x 90 x 134 mm (incl. connector) (incl. connector) 7-16 male 67 x 90 x 133 mm (incl. connector) K 62 26 30 1 100 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz Application Weight Packing size Dimensions (w x h x d) K 62 26 50 1 K 62 26 51 1 K 62 26 50 7 N female N male 0 – 1000 MHz < 1.08 Indoor Approx. 2.4 kg 130 x 195 x 180 mm 114 x 161 x 156 mm (including connector) 7-16 female 114 x 153 x 156 mm (including connector) 114 x 170 x 156 mm (including connector) K 62 26 50 1 * Rated power at 40 °C ambient temperature. The max. power rating increases or decreases with falling or rising ambient temperature. Note: The 50-Ohm load, type 782 010474, should be used if intermodulation requirements are of high priority. 297 50-Ohm Load 698 – 2700 MHz 80 W • Designed as 50-Ohm termination wherever improved intermodulation performance compared to standard loads is required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • Built-in DC stop RF Port Technical Data 782 10474 Type No. Frequency range VSWR Impedance Input power Intermodulation products Temperature range Connector Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 698 – 2700 MHz < 1.12 50 Ω < 80 W (see table) < –160 dBc (3rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Built-in DC stop AISG: Attenuation up to 3 dB when used in a network Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set (see data sheet) 3.1 kg 377 x 232 x 189 mm 143.6 x 216 x 79.2 mm (including connector) Note: The RF port connector should always point downwards if mounted outdoors. The input power rating of 80 W is specified at an ambient temperature of +40 °C with the combiner mounted vertically, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). The max. power rating increases or decreases with falling or rising ambient temperature and depending on horizontal or vertical mounting in accordance with the following table: Max. input power Mounted horizontally Mounted vertically 50 W 70 W 90 W 60 W 80 W 100 W Max. ambient temperature +55 °C +40 °C +25 °C 298 Attenuator 2 – 15 W 0 – 4000 MHz Air-cooled attenuator for low power rating • Signal attenuation for test, measuring or tuning purposes • Good matching over large frequency range • Closed metal housing, very stable and RF proof • Free choice of mounting position due to convection-cooling Technical Data Type No. Attenuation Frequency range VSWR Impedance Max. power 784 10235 3 ±0.3 dB 784 10236 784 10237 6 ±0.3 dB 10 ±0.3 dB 0 – 4000 MHz < 1.12 50 Ω 2W Connectors IP rating Application Weight Dimensions (L x diameter) 784 10238 20 ±0.5 dB N IP65 Outdoor 60 g 49 x 21 mm Air-cooled attenuator for medium power rating • Signal attenuation for test, measuring or tuning purposes • Good matching over large frequency range • Closed metal housing, very stable and RF proof • Free choice of mounting position due to convection-cooling Technical Data Type No. Attenuation Max. power Frequency range VSWR Impedance Connectors IP rating Application Weight Dimensions (L x diameter) 791 918 3 ±0.3 dB 15 W 791 919 791 920 6 ±0.3 dB 10 ±0.3 dB 12 W 10 W 0 – 4000 MHz < 1.15 50 Ω N IP65 Outdoor 70 g 50 x 26 mm 791 921 20 ±0.5 dB 10 W 299 Measuring Directional Coupler 824 – 2500 MHz The Measuring Directional Coupler provides measurement ports for monitoring the forward and reflected power of a RF signal. • Easy implementation into existing RF systems due to male/female connectors • Input and output ports are reciprocal in nature • Front panel mounting possible via flange • Suitable for indoor applications Forward Port Output Port Input Port Reflected Port 102.8 Technical Data 792 972 Type No. Frequency range Insertion loss Input port Output port Coupling attenuation Input port Forward port Output port Reflected port Directivity VSWR Input port, Output port Forward port, Reflected port Impedance Input power Intermodulation products Temperature range Connectors Input port Output port Forward port, Reflected port Application Mounting Weight Dimensions (w x h x d) 300 824 – 2500 MHz < 0.05 dB (824 – 2500 MHz) 32.0 ±0.75 dB (824 – 960 MHz) 28.5 ±1.50 dB (1710 – 2500 MHz) 32.0 ±0.75 dB (824 – 960 MHz) 28.5 ±1.50 dB (1710 – 2500 MHz) > 28 dB (824 – 2200 MHz)3 > 25 dB (2200 – 2500 MHz) < 1.04 (824 – 960 MHz) < 1.08 (960 – 2500 MHz) < 1.2 (824 – 2500 MHz) 50 Ω < 800 W (824 – 960 MHz) < 200 W (960 – 2500 MHz) < –160 dBc (3rd order; with 2 x 20 W) –20 … +55 °C 7-16 male 7-16 female MCX female Indoor Front panel mounting possible with 4 screws (max. 2.5 mm diameter) 0.26 kg 32 x 32 x 102.3 mm DTMAs DTMAs 301 Summary of DTMA Types DTMAs: Description Type No. Frequency range Gain Page DTMA-800-12-AISG 782 10430 UL: 791 – 821 / DL: 832 – 862 MHz 12 dB 303 DTMA-1800-12-CWA 782 10580 UL: 1805 – 1880 / DL: 1710 – 1785 MHz 12 dB 305 DTMA-1800-12-AISG 782 10581 UL: 1805 – 1880 / DL: 1710 – 1785 MHz 12 dB 305 DTMA-1900-850 BYP-12-AISG 782 10406 UL: 1850 – 1910 / DL: 1930 – 1990 MHz Bypass: 806 – 896 MHz 12 dB Single Mode AISG or CWA 307 DTMA-UMTS-24-AISG 782 10448 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 24 dB 311 DTMA-2600-12-AISG 782 10860 UL: 2500 – 2570 / DL: 2620 – 2690 MHz 12 dB 316 DTMA-900-12-32-AISG-CWA 782 10440 UL: 880 – 915 / DL: 925 – 960 MHz 12/32 dB 304 DTMA-900-12-32-AISG-CWA 782 10442 UL: 880 – 915 / DL: 925 – 960 MHz 12/32 dB 304 DTMA-1800-12-AISG-CWA 782 10555 UL: 1710 – 1785 / DL: 1805 – 1880 MHz 12 dB 306 DTMA-1800-12-AISG-CWA 782 10556 UL: 1710 – 1785 / DL: 1805 – 1880 MHz 12 dB 306 DTMA-1800-12-AISG-CWA 782 10557 UL: 1710 – 1785 / DL: 1805 – 1880 MHz 12 dB 306 DTMA-1800-12-AISG-CWA 782 10558 UL: 1710 – 1785 / DL: 1805 – 1880 MHz 12 dB 306 DTMA-1900-12-AISG-CWA 782 10811 UL: 1850 – 1910 / DL: 1930 – 1990 MHz 12 dB 308 DTMA-UMTS-12-AISG-CWA 782 10153 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 12 dB 309 DTMA-UMTS-12-AISG-CWA 782 10154 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 12 dB 309 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10561 UL: 1970 – 1985 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10562 UL: 1970 – 1985 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10563 UL: 1965 – 1980 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10564 UL: 1965 – 1980 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10565 UL: 1950 – 1965 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10566 UL: 1920 – 1935 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10567 UL: 1920 – 1935 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10568 UL: 1950 – 1965 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10569 UL: 1970 – 1985 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10570 UL: 1920 – 1935 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10571 UL: 1965 – 1980 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA-FB-BS 782 10579 UL: 1965 – 1980 / DL: 2110 – 2170 MHz 12 dB 310 DTMA-UMTS-12-AISG-CWA 782 10610 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 12 dB 312 DTMA-UMTS-12-AISG-CWA 782 10612 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 12 dB 312 DTMA-UMTS-24-AISG-CWA 782 10613 UL: 1920 – 1980 / DL: 2110 – 2170 MHz 24 dB 313 DTMA-UMTS-BYP900/1800-12-AISG-CWA 782 10652 UL: 1920 – 1980 / DL: 2110 – 2170 MHz Bypass: 870 – 960 MHz 1710 – 1880 MHz 12 dB DTMA-UMTS-BYP900/1800-12-AISG-CWA 782 10653 UL: 1920 – 1980 / DL: 2110 – 2170 MHz Bypass: 870 – 970 MHz 1710 – 1880 MHz 12 dB Dual Mode AISG and CWA New Products 302 UL = Up Link / DL = Down Link 314, 315 314, 315 DTMA-800-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports AISG 2.0 • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Node B0 RET Node B1 Technical Data Type No. 782 10430 DTMA-800-12-AISG (12 dB gain) Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Loss in by-pass mode Return loss Gain Noise figure 3rd order intercept point (OIP3) Environmental Characteristics Operating temperature range IP rating MTBF EMC DC and Alarm Characteristics DC supply Operating current per DTMA (without RET) Alarm management Mechanical Characteristics Material Connectors RF AISG Mounting Weight Dimensions (w x h x d) 791 – 821 MHz Typically 0.25 dB < 0.3 dB < 100 W (+50 dBm) CW < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB 832 – 862 MHz Typically 2 dB > 16 dB (DC ON) 12 dB nominal Typically 1.2 dB Typically 30 dBm –40 … +65 °C IP67 > 1 000 000 hours (per TMA) According to ETS 300 342-3 10 – 30 V DC Nom. 100 mA at 10 V DC / Nom. 50 mA at 30 V DC AISG Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 6.5 kg 240 x 170 x 98 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm 303 DTMA-900-12-32-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double units for easy use with XPol antennas • Gain setting switchable from 12 dB (default) to 32 dB • Both versions support CWA, AISG 1.1 and AISG 2.0 (default) 782 10440: CWA alarm 170 – 200 mA / 800 – 900 mA 782 10442: CWA alarm 230 – 295 mA / 800 – 900 mA • AISG and gain setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. 782 10440 CWA alarm 170 – 200 mA / 800 – 900 mA DTMA-900-12-32-AISG-CWA (12/32 dB gain) CWA alarm 230 – 295 mA / 800 – 900 mA DTMA-900-12-32-AISG-CWA (12/32 dB gain) 782 10442 Tx Characteristics Frequency range 925 – 960 MHz Insertion loss * < 0.5 dB Input power (per input) < 180 W (+52.5 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 880 – 915 MHz Loss in by-pass mode < 4 dB (DC OFF) Return loss > 16 dB (DC ON) / > 12 dB (DC OFF) Gain 12/32 ±0.7 dB (+22 … +28 °C) 12/32 ±1.0 dB (– 40 ... +55 °C) Noise figure ** < 1.3 dB (+22 ... +28 °C) Input 1-dB compression point > – 7 dBm Input 3rd order intercept point (IIP3) > 5 dBm Environmental Characteristics Operating temperature range –40 … +55 °C IP rating IP 67 MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 8.5 – 15 V 10 – 30 V Operating current per TMA 80 – 130 mA (12 dB gain) < 110 mA (12 dB gain) (without RET) 360 – 400 mA (32 dB gain) < 350 mA (32 dB gain) Alarm management 12 dB gain 782 10440: 170 – 200 mA AISG *** 782 10442: 230 – 295 mA 32 dB gain 800 – 900 mA Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Weight 8.7 kg Packing size 342 x 579 x 212 mm Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Dimensions (w x h x d) 250 x 353 x 94 mm (without connectors, without mounting brackets) * Insertion loss IL = ** Noise figure NF = IL925 MHz + 2 x IL942.5 MHz + IL960 MHz 4 NF880 MHz + 2 x NF897.5 MHz + NF915 MHz 4 (Additional variation at –40 ... +55 °C: Δ NF < 0.3 dB) 304 Accessories (order separately) Type No. 734 734 734 734 734 734 360 361 362 363 364 365 Clamp set suitable for mast diameter of 34 60 80 100 120 45 – – – – – – 60 80 100 120 140 125 mm mm mm mm mm mm *** AISG and Gain Setting The protocol of the software interface can be switched between AISG 2.0 / 3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start-up. Please contact Kathrein for further information. Gain setting according to AISG commands. DTMA-1800-12-CWA DTMA-1800-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) Ant 1 • Double units for easy use with XPol antennas • AISG setting switchable • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm BTS 0 BTS 1 782 10580 Ant 1 Ant 0 Technical Data Type No. 782 10580 782 10581 DTMA-1800-12-CWA (12 dB gain) DTMA-1800-12-AISG (12 dB gain) Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Loss in by-pass mode Return loss Gain Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) Environmental Characteristics Operating temperature range IP rating MTBF EMC DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management Mechanical Characteristics Material Connectors RF AISG Weight Mounting Packing size Dimensions (w x h x d) 1805 – 1880 MHz Typically 0.2 dB < 200 W (+53 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB BTS 0 BTS 1 782 10581 782 10581 1710 – 1785 MHz Typically 1.7 dB (DC OFF) > 16 dB (DC ON) > 16 dB (DC ON) / > 15 dB (DC OFF) 12 dB nominal Typically 1.0 dB > 10 dBm Typically 30 dBm –40 … +65 °C IP 67 > 1 000 000 hours (per TMA) According to ETS 300 342-3 CWA Mode 7.5 – 15 V Typically 80 mA 230 – 290 mA AISG Mode 10 – 30 V Nom. 195 mA at 10 V Nom. 85 mA at 30 V AISG 782 10580 Aluminium housing 7-16 female (long neck) 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: Not connected) 4 kg Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 405 x 235 x 175 mm 220 x 170 x 71.5 mm (without connectors, without mounting brackets) 305 DTMA-1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double units for easy use with XPol antennas • All versions support CWA, AISG 1.1 and AISG 2.0 782 10555: Default setting AISG 1.1, CWA alarm 170 – 200 mA 782 10556: Default setting AISG 1.1, CWA alarm 230 – 295 mA 782 10557: Default setting AISG 2.0, CWA alarm 170 – 200 mA 782 10558: Default setting AISG 2.0, CWA alarm 230 – 295 mA AISG setting switchable • CWA and AISG configurations • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection • RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Ant 1 Ant 0 Technical Data 782 10555 Default setting AISG 1.1 CWA alarm 170 – 200 mA DTMA-1800-12-AISG-CWA (12 dB gain) Default setting AISG 1.1 CWA alarm 230 – 295 mA DTMA-1800-12-AISG-CWA (12 dB gain) Default setting AISG 2.0 CWA alarm 170 – 200 mA DTMA-1800-12-AISG-CWA (12 dB gain) Default setting AISG 2.0 CWA alarm 230 – 295 mA DTMA-1800-12-AISG-CWA (12 dB gain) 782 10556 782 10557 782 10558 Tx Characteristics Frequency range 1805 – 1880 MHz Insertion loss* < 0.4 dB Input power (per input) < 160 W (+52 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1710 – 1785 MHz Loss in by-pass mode Typically 2.8 dB (DC OFF) Return loss > 18 dB (DC ON) / > 15 dB (DC OFF) Gain 12 ±0.7 dB (+22 … +28 °C) / 12 ±1.3 dB (– 40 ... +65 °C) Noise figure** < 1.4 dB (+22 ... +28 °C) Output 1-dB compression point > 10 dBm 3 rd order intercept point (OIP3) > 25 dBm Environmental Characteristics Operating temperature range –40 … +65 °C IP rating IP 67 MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 – 15 V 9 – 30 V Operating current per TMA 80 – 130 mA Nom. 95 mA at 9 V (without RET) Nom. 35 mA at 30 V Alarm management 782 10555: 170 – 200 mA 782 10556: 230 – 295 mA AISG *** 782 10557: 170 – 200 mA 782 10558: 230 – 295 mA Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Weight 5 kg Packing size 262 x 502 x 214 mm Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Dimensions (w x h x d) 166 x 278 x 77.5 mm (without connectors, without mounting brackets) * Insertion loss IL = ** Noise figure NF = Node B0 RET BTS 0 Node B1 BTS 1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm IL1805 MHz + 2 x IL1842.5 MHz + IL1880 MHz 4 NF1710 MHz + 2 x NF1747.5 MHz + NF1785 MHz 4 (Additional variation at –40 ... +65 °C: Δ NF < 0.5 dB) *** The protocol of the software interface can be switched between AISG 2.0/3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start up. Please contact Kathrein for further information. 306 DTMA-1900-850 BYP-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • RF-Bypass feature for 850 MHz • DC-stop integrated to 850 MHz ports • Kathrein redundancy amplifier design for improved system reliability • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection • Compact size • Suitable for antenna RET control according to AISG standard • DTMA DC supply and AISG feed via BTS 0 port for both TMAs Ant 1 Ant 1 Ant 0 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group BYP = RF-BYPass Technical Data 782 10406 Type No. DTMA-1900-850 BYP-12-AISG (12 dB gain) 850 MHz Bypass Frequency range Insertion loss Isolation to 1900 MHz Input power Return loss 1900 MHz DTMA Tx Characteristics Frequency range Bandwidth Insertion loss Input power Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Bandwidth Loss in by-pass mode Return loss 806 – 896 MHz < 0.15 dB > 80 dB 500 W CW / per input > 18 dB 1930 – 1990 MHz 60 MHz < 0.5 dB at 80% of BW, a further 0.25 dB at 100% BW. < 160 W (+52 dBm) CW / per input < 1.6 kW (+62 dBm) Peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Output 1-dB compression point 3 rd order intercept point (OIP3) 1850 – 1910 MHz 60 MHz 2.8 dB typically > 18 dB (DC ON) > 15 dB (DC OFF) 12 ±0.7 dB 12 ±1.3 dB < 1.7 dB at 80% of BW, a further 0.3 dB at 100% BW. < 2.2 dB at 80% of BW, a further 0.3 dB at 100% BW. > 15 dBm > 25 dBm Environmental Characteristics Operating temperature range IP rating MTBF –40 … +65 °C IP67 > 1 000 000 hours (per TMA) Gain Noise figure +22 … +28 °C –40 … +65 °C +22 … +28 °C Noise figure –40 … +65 °C EMC Lightning protection DC and Alarm Characteristics DC supply without RET Alarm management Modem Characteristics Mechanical Characteristics Material Connectors RF AISG Connector (Compliance AISG 1.1) Mounting Weight Dimensions (w x h x d) ETS 300 342-3 5 kA, 8/20 μs RF connections and AISG port BTS 0 AISG and DC-Port RET BTS 1 BTS 1 BTS 0 Through BTS 0 Port only +12 V nominal (9 – 15 V, minus grounded) Typically 150 mA per TMA According to AISG standard 1.1 According to AISG standard 1.1 (Data rate: 9.6 kB) Aluminium housing 7-16 female 8-pin female, IEC 60130-9 (Pin 1: +12 V DC nominal, pin 3: RS485B, pin 5: RS485A, pin 7: DC return; other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Approx. 8.7 kg 271 x 278 x 77.5 mm (without connectors, without mounting brackets) BTS 0 BTS 1 307 DTMA-1900-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data 782 10811 Type No. DTMA-1900-12-AISG-CWA (12 dB gain) Tx Characteristics Frequency range 1930 – 1990 MHz Insertion loss* < 0.5 dB Input power (per input) < 160 W (+52 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1850 – 1910 MHz Loss in by-pass mode Typically 2.8 dB (DC OFF) Return loss > 18 dB (DC ON) / > 15 dB (DC OFF) Gain 12 ±0.7 dB (+22 … +28 °C) / 12 ±1.3 dB (– 40 ... +65 °C) Noise figure** < 1.4 dB (+22 ... +28 °C) Output 1-dB compression point > 10 dBm 3rd order intercept point (OIP3) > 25 dBm Environmental Characteristics Operating temperature range –40 … +65 °C IP rating IP67 MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA-Mode AISG-Mode DC supply 9 – 15 V 9 – 30 V Operating current per TMA 80 – 130 mA Nom. 95 mA at 9 V (without RET) Nom. 35 mA at 30 V Alarm management 170 – 200 mA AISG*** Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Weight 5 kg Packing size 262 x 502 x 214 mm Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Dimensions (w x h x d) 166 x 278 x 77.5 mm (without connectors, without mounting brackets) * Insertion loss IL = ** Noise figure NF = BTS 0 RET Ant 0 IL1930 MHz + 2 x IL1960 MHz + IL1990 MHz BTS 1 Ant 1 DTMA 4 NF1850 MHz + 2 x NF1880 MHz + NF1910 MHz 4 BTS 0 BTS 1 (Additional variation at –40 ... +65 °C: Δ NF < 0.5 dB) *** The protocol of the software interface can be switched between AISG 2.0/3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start up. Please contact Kathrein for further information. 308 DTMA-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double units for easy use with XPol antennas • Both versions support CWA, AISG 1.1 and AISG 2.0 782 10153 default setting: AISG 1.1 782 10154 default setting: AISG 2.0 Ant 1 • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. 782 10153 Default setting AISG 1.1 DTMA-UMTS-12-AISG-CWA (12 dB gain) Default setting AISG 2.0 DTMA-UMTS-12-AISG-CWA (12 dB gain) 782 10154 Tx Characteristics Frequency range 2110 – 2170 MHz Insertion loss Typ. 0.3 dB Ripple < 0.1 dB Input power (per input) < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1920 – 1980 MHz Loss in by-pass mode < 2.5 dB (DC OFF) Return loss > 18 dB (DC ON) / > 12 dB (DC OFF) Gain 12 ±0.5 dB (+22 … +28 °C) / 12 ±1.0 dB (– 40 ... +65 °C) Gain ripple < ±0.3 dB Noise figure < 1.6 dB (25 °C) / < 2.0 dB (60 °C) Output 1-dB compression point > 15 dBm 3rd order intercept point (OIP3) > 25 dBm Environmental Characteristics Operating temperature range –40 … +65 °C IP rating IP67 MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 – 15 V 9 – 30 V Operating current per TMA 80 – 145 mA Nom. 115 mA at 9 V (without RET) Nom. 40 mA at 30 V Alarm management 170 – 200 mA AISG* Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Weight 5 kg Packing size 262 x 502 x 214 mm Dimensions (w x h x d) 166 x 262 x 77.5 mm (without connectors, without mounting brackets) Node B0 RET Node B1 Node B0 Node B1 Ant 0 Ant 1 DTMA Node B0 Node B1 * The protocol of the software interface can be switched between AISG 2.0/3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start up. Please contact Kathrein for further information. 309 DTMA-UMTS-12-AISG-CWA-FB-BS Tx-Fullband / Rx-Band Selective Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports AISG 1.1 and 2.0 (default version see table)* • Kathrein redundancy amplifier design for improved system reliability • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection • Compact size • DC supply • • • Ant 1 Ant 0 CWA: Via Node B0 and B1 AISG: Via Node B0, Node B1 or both Signalling CWA: Via Node B0 and B1 for each LNA AISG: Via Node B0, Node B1 for both LNAs Suitable for antenna RET control according to AISG/3GPP standard DTMA DC supply and AISG feed via Node B0 or Node B1 port for both TMAs RET AISG FB BS CWA Ant 0 = Remote Electrical Tilt = Antenna Interface Standards Group = Full Band in Tx-Band = Band Selective in Rx-Band = Current Window Alarm Ant 1 DTMA Node B0 Node B1 Technical Data Type Tx Characteristics Frequency range Bandwidth Insertion loss Ripple Max. Group Delay Max. Delta Group Delay in 5 MHz Bandwidth Input power Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Bandwidth Loss in by-pass mode Gain ripple Return loss Gain +22 … +28 °C –40 … +60 °C Max. Group Delay Max. Delta Group Delay in 5 MHz Bandwidth Noise figure Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) Environmental Characteristics Operating temperature range IP rating MTBF EMC DC and Alarm Characteristics DC supply Alarm management Modem Characteristics Mechanical Characteristics Material Connectors RF AISG Connector (Compliance AISG) Mounting Weight Packing size Dimensions (w x h x d) DTMA-UMTS-12-AISG-CWA-FB-BS (12 dB gain) Node B0 2110 – 2170 MHz 60 MHz < 0.4 dB < 0.1 dB 50 ns 5 ns RET Node B1 < 100 W (+50 dBm) CW < 1.6 kW (+62 dBm) Peak < –122 dBm (2 x 43 dBm carriers) > 18 dB factory tunable within 1920 – 1985 MHz 15 MHz < 3.0 dB (DC OFF) < 0.4 dB > 18 dB (DC ON) > 16 dB (DC OFF) 12 ±0.5 dB 12 ±1.0 dB 100 ns 10 ns < 1.5 dB / 25 °C < 1.8 dB / 60 °C > 7 dBm > 17 dBm –40 … +60 °C IP67 > 1 000 000 hours ETS 300 342-3 9 – 30 V, minus grounded CWA or according to AISG standard* According to AISG standard* Aluminium housing 7-16 female long neck 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return; other pins: NC) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 5 kg 262 x 502 x 214 mm 166 x 262 x 77.5 mm (without connectors, without mounting brackets) Node B1 Node B0 Type no. Rx-Frequency (MHz) AISG 1.1 (default version) 782 10561 1970 – 1985 Current in CWA mode (mA) nominal alarm 50 – 190 230 – 295 782 10562 1970 – 1985 80 – 120 170 – 200 782 10563 1965 – 1980 50 – 190 230 – 295 782 10564 1965 – 1980 80 – 120 170 – 200 782 10565 1950 – 1965 80 – 120 170 – 200 782 10566 1920 – 1935 50 – 190 230 – 295 782 10567 1920 – 1935 80 – 120 170 – 200 782 10568 1950 – 1965 50 – 190 230 – 295 Type no. Rx-Frequency (MHz) AISG 2.0 (default version) Current in CWA mode (mA) nominal alarm 782 10569 1970 – 1985 50 – 190 230 – 295 782 10570 1920 – 1935 50 – 190 230 – 295 782 10571 1965 – 1980 50 – 190 230 – 295 782 10579 1965 – 1980 80 – 120 170 – 200 * The protocol of the software interface can be switched between AISG 2.0/3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start up. Please contact Kathrein for further information. 310 DTMA-UMTS-24-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports AISG 1.1 or 2.0 (Default version AISG 1.1) * • Kathrein redundancy amplifier design for improved system reliability • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection • Compact size • Suitable for antenna RET control according to AISG/3GPP standard • DTMA DC supply and AISG feed via Node B0 port for both TMAs Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Technical Data Type No. 782 10448 DTMA-UMTS-24-AISG (24 dB gain) Tx Characteristics Frequency range Bandwidth Insertion loss Ripple Input power Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Bandwidth Loss in by-pass mode Gain ripple Return loss 2110 – 2170 MHz 60 MHz Typically 0.3 dB < ±0.2 dB < 100 W (+50 dBm) CW < 1.6 kW (+62 dBm) Peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB 24 ±1.0 dB 24 ±0.5 dB Typically 1.4 dB > 20 dBm > 29 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC Lightning protection –40 … +65 °C IP67 > 1 000 000 hours (per TMA) ETS 300 342-3 5 kA, 8/20 μs RF connections and AISG port Alarm management Mechanical Characteristics Material Connectors RF AISG Connector (Compliance AISG) Mounting Weight Packing size Dimensions (w x h x d) Node B1 RET 1920 – 1980 MHz 60 MHz Typically 2.4 dB (DC OFF) < ±0.3 dB > 18 dB (DC ON) > 12 dB (DC OFF) Gain –40 … +65 °C +22 … +28 °C Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) DC and Alarm Characteristics DC supply without RET Node B0 AISG and DC-Port Through Node BO Port only 9 – 30 V, minus grounded Typically 300 mA at 9 V Typically 100 mA at 30 V According to AISG standard* Node B1 Node B0 Aluminium housing 7-16 female 8-pin female, IEC 60130-9 (Pin 6: 9 – 30 V DC, pin1: 9-15 V DC, pin 3: RS485B, pin 5: RS485A, pin 7: DC return; other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 5 kg 262 x 502 x 214 mm 166 x 262 x 77.5 mm (without connectors, without mounting brackets) Ant 0 Ant 1 DTMA Node B0 Node B1 * The protocol of the software interface can be switched between AISG 2.0/3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start up. Please contact Kathrein for further information. 311 DTMA-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Slimline design • Double units for easy use with XPol antennas • Both versions support CWA, AISG 1.1 and AISG 2.0 Ant 1 782 10610 default setting: AISG 1.1 782 10612 default setting: AISG 2.0 Ant 0 • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. Default setting AISG 1.1 Default setting AISG 2.0 Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in Rx band Return loss 782 10610 DTMA-UMTS-12-AISG-CWA (12 dB gain) Node B0 782 10612 RET Node B1 DTMA-UMTS-12-AISG-CWA (12 dB gain) 2110 – 2170 MHz < 0.3 dB (typically 0.15 dB) < 0.1 dB < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range 1920 – 1980 MHz Loss in by-pass mode < 2.5 dB (DC OFF) Return loss > 18 dB (DC ON) / > 12 dB (DC OFF) Gain 12 ±1.0 dB (+22 … +28 °C) / 12 ±1.2 dB (– 40 ... +65 °C) Gain ripple < ±0.3 dB Noise figure* < 1.3 dB (+22 ... +28 °C) Output 1-dB compression point > 11 dBm 3rd order intercept point (OIP3) > 25 dBm (typically 30 dBm) Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67 > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) * Noise figure NF = CWA Mode 9 – 15 V 80 – 140 mA 170 – 200 mA Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3.8 kg 262 x 502 x 214 mm 160 x 205 x 63 mm (without connectors, without mounting brackets) NF1920 MHz + 2 x NF1950 MHz + NF1980 MHz 4 (Additional variation at –40 ... +65 °C: Δ NF < 0.3 dB) 312 AISG Mode 9 – 30 V Nom. 95 mA at 9 V Nom. 35 mA at 30 V AISG Node B0 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm DTMA-UMTS-24-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Slimline design • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data 782 10613 Type No. DTMA-UMTS-24-AISG-CWA (24 dB gain) Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in Rx band Return loss Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67 > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management Weight Packing size Dimensions (w x h x d) * Noise figure NF = Node B1 < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB 1920 – 1980 MHz < 2.5 dB (DC OFF) > 18 dB (DC ON) / > 12 dB (DC OFF) 24 ±1.0 dB (+22 … +28 °C) / 24 ±1.2 dB (– 40 ... +65 °C) < ±0.3 dB < 1.4 dB (+22 ... +28 °C) > 18 dBm > 25 dBm (typically 30 dBm) Mounting RET 2110 – 2170 MHz < 0.3 dB (typically 0.15 dB) < 0.1 dB < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Rx Characteristics Frequency range Loss in by-pass mode Return loss Gain Gain ripple Noise figure* Output 1-dB compression point 3rd order intercept point (OIP3) Mechanical Characteristics Material Connectors RF AISG Node B0 CWA Mode 9 – 15 V 130 – 340 mA 380 – 420 mA AISG Mode 9 – 30 V Nom. 210 mA at 9 V Nom. 70 mA at 30 V AISG Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3.8 kg 262 x 502 x 214 mm 160 x 205 x 63 mm (without connectors, without mounting brackets) Node B0 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm NF1920 MHz + 2 x NF1950 MHz + NF1980 MHz 4 (Additional variation at –40 ... +60 °C: Δ NF < 0.4 dB) 313 DTMA-UMTS-BYP900/1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier with 900 MHz and 1800 MHz By-pass • Double units for easy use with XPol antennas • Both versions support CWA, AISG 1.1 and AISG 2.0 (default) 782 10652: CWA alarm 170 – 200 mA 782 10653: CWA alarm 230 – 295 mA • RF Bypass for 900 MHz and 1800 MHz • Integrated DC stops • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection RET AISG CWA BYP = Remote Electrical Tilt = Antenna Interface Standards Group = Current Window Alarm = RF BYPass Ant 0 1800 Ant 0 900 Ant 1 900 Ant 1 1800 Ant 1 UMTS Ant 0 UMTS Technical Data Type No. 782 10652 CWA alarm 170 – 200 mA DTMA-UMTS-BYP900/1800-12-AISG-CWA (12 dB gain) CWA alarm 230 – 295 mA DTMA-UMTS-BYP900/1800-12-AISG-CWA (12 dB gain) 782 10653 UMTS Tx Characteristics Frequency range 2110 – 2170 MHz Insertion loss < 0.4 dB Return loss > 18 dB Input power (per input) < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) UMTS Rx Characteristics Frequency range 1920 – 1980 MHz Loss in by-pass mode < 3.0 dB (DC OFF) Return loss > 16 dB (DC ON) / > 14 dB (DC OFF) Gain 12 ±0.7 dB (+22 … +28 °C) / 12 ±1.3 dB (– 40 ... +60 °C) Gain ripple in 5 MHz bandwidth < ±0.2 dB Noise figure* < 1.3 dB (+22 ... +28 °C) Output 1-dB compression point > 10 dBm 3rd order intercept point (OIP3) > 23 dBm 1800 MHz Bypass Characteristics Frequency range 1710 – 1880 MHz Insertion loss < 0.3 dB Return loss > 18 dB Isolation > 80 dB (2400 – 2900 MHz) / > 60 dB (2110 – 2170 MHz) / > 50 dB (2010 – 2025 MHz) / > 50 dB (1920 – 1980 MHz) / > 80 dB (880 – 960 MHz) Input power (per input) 100 W CW / 300 W peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) 900 MHz Bypass Characteristics Frequency range 870 – 970 MHz Insertion loss < 0.3 dB Return loss > 18 dB Isolation > 70 dB (2400 – 2900 MHz) / > 60 dB (2110 – 2170 MHz) / > 60 dB (2010 – 2025 MHz) / > 55 dB (1920 – 1980 MHz) / > 30 dB (1710 – 1880 MHz) Input power (per input) 100 W CW / 300 W peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Environmental Characteristics Operating temperature range –40 … +60 °C IP rating IP67 (see note on data sheet) MTBF > 1 000 000 hours per TMA EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 – 15 V 9 – 30 V Operating current per TMA 80 – 140 mA Nom. 95 mA at 9 V (without RET) Nom. 35 mA at 30 V Alarm management 782 10652: 170 – 200 mA AISG 782 10653: 230 – 295 mA Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Dimensions (w x h x d) 222 x 316.9 x 108.5 mm (without connectors, without mounting brackets) 314 Node B0 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. Description 784 10367 50-Ω load 1.5 W / indoor or outdoor * Noise figure NF = Clamp Set 50-Ω load NF1920 MHz + 2 x NF1950 MHz + NF1980 MHz 4 (Additional variation at –40 ... +60 °C: Δ NF < 0.3 dB) DTMA-UMTS-BYP900/1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier with 900 MHz and 1800 MHz By-pass DC Supply, Current Window Alarm and AISG Configuration (automatically chosen by the DTMA depending on incoming signals) 782 10652, 782 10653 Application Example AISG Setting The protocol of the software interface can be switched between AISG 2.0 / 3GPP and AISG 1.1 and vice versa with a vendor specific command (depending on default setting). If the primary station does not support the default setting, it has to be switched over before system start-up. Please contact Kathrein for further information. 315 DTMA-2600-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • DC/AISG by-pass between ports “Node B0 or Node B1“ and “Ant 0“ for Ant 1 Ant 0 the support of RET integrated antennas (incl. short circuit protection) • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Node B0 Node B1 RET Technical Data Type No. 782 10860 DTMA-2600-12-AISG (12 dB gain) Tx Characteristics Frequency range 2620 – 2690 MHz Insertion loss Typically 0.3 dB Ripple < 0.35 dB Input power (per input) < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 2500 – 2570 MHz Loss in by-pass mode Typically 2 dB Return loss > 18 dB (DC ON) Gain 12 dB nominal Noise figure Typically 1.2 dB Output 1-dB compression point > 13 dBm 3rd order intercept point (OIP3) Typically 30 dBm Environmental Characteristics Operating temperature range –40 … +65 °C IP rating IP67 MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics DC supply 10 – 30 V Operating current per DTMA Nom. 175 mA at 10 V DC (without RET) Nom. 70 mA at 30 V DC Alarm management AISG Mechanical Characteristics Material Aluminium housing Connectors RF 7-16 female (long neck) AISG 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 – 30 V DC, pin 7: DC return, other pins: not connected) Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Weight 3.5 kg Packing size 217 x 407 x 144 mm Dimensions (w x h x d) 165.3 x 236.4 x 65.1 mm (without connectors, without mounting brackets) 316 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Clamp Set Sales queries, orders, catalogues or CD-ROM: Fax: +49 80 31 184-820 E-Mail: [email protected] Technical Information: Fax: +49 80 31 184-973 E-Mail: [email protected] Internet: www.kathrein.de KATHREIN-Werke KG . Phone +49 80 31 184-0 . Fax +49 80 31 184-973 Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . D-83004 Rosenheim . Germany 9981.1576/1210/6/ZW/FO Please contact for Subject to alteration. A current list of Kathrein’s International Representatives can be found on our homepage: www.kathrein.de 790 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications Catalogue 2011 Subsidiaries/Affiliates Catalogue 2011 790 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021