BIXOLON | SRP-770II | User's Manual | BIXOLON SRP-770II User's Manual

BIXOLON SRP-770II User's Manual
User's Manual
SRP-770II
Label Printer
Rev. 1.14
http://www.bixolon.com
SRP-770II
■ Table of Contents
※ Manual Information & Usage Precautions ··································································3
1. Content Confirmation ····································································································7
2. Product Part Names·······································································································8
3. Installation & Usage·····································································································10
3-1 Power Connection ····································································································10
3-2 Interface Cable Connection ······················································································ 11
3-3 Paper Installation ······································································································12
3-4 LED Display ··············································································································13
4. Self-Test························································································································14
5. Fine Tuning···················································································································15
5-1 Printer Settings with Dip switches·············································································15
5-2 Pause/Restart ···········································································································16
5-3 Gap Sensor Auto-Calibration ····················································································17
5-4 Gap Sensor Manual-Calibration ···············································································18
5-5 The Peel-Off ·············································································································19
5-6 Using Fan-Fold Paper·······························································································21
5-7 Auto Cutter (option)···································································································22
6. Cleaning Head··············································································································23
7. Appendix·······················································································································24
7-1 Specifications············································································································24
7-2 Certification···············································································································25
7-3 Label Types ··············································································································25
Rev. 1.14
-2-
SRP-770II
■ Manual Information
※ Manual Information & Usage Precautions
This user manual contains basic information for product usage as well as for emergency
measures that may be required.
※ The following separate manuals provide more detailed content on various technological
issues and areas.
1. Windows Driver Manual
This manual provides information on the installation instructions and main functions
of the Windows Driver.
2. Unified Label Printer Utility Manual
This manual provides information on the usage of software for function selection of
this product, operating condition modification, etc.
The following functions are available.
1) Firmware Downloader
2) Factory Font Downloader
3) Soft-Font (or Downloadable-font) Downloader
4) PCX File Downloader
5) User Setting Manager
6) File Transfer Manager
7) SLCS Tester
3. Z Driver Manual
This manual provides information on the usage of the Z Driver, which contains a
function that can reduce A4-sized original copy data to 4-inch size.
4. Programming (SLCS) Manual
This manual provides information on label printer commands.
5. True Font Downloader Manual
This manual provides information on the usage of the font downloader that can
download True Fonts and facilitate their usage as Device Fonts.
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and
quality of all our products. In following, product specifications and/or user manual content
may be changed without prior notice.
Rev. 1.14
-3-
SRP-770II
■ Safety Precautions
In using the present appliance, please keep the following safety regulations in order to
prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not plug several products in one multi-outlet.
•
•
•
•
You must use only the supplied adapter.
This can provoke over-heating and a fire.
If the plug is wet or dirty, dry or wipe it before usage.
If the plug does not fit perfectly with the outlet, do not plug in.
Be sure to use only standardized multi-outlets.
• It is dangerous to use other adapters.
ONLY SUPPLIED ADAPTER
PROHIBIT
PROHIBIT
Do not pull the cable to unplug.
Keep the plastic bag out of children’s reach.
• This can damage the cable, which is the origin of a fire or a
breakdown of the printer.
• If not, a child may put the bag on his head.
PROHIBIT
Do not plug in or unplug with your hands wet.
• You can be electrocuted.
PROHIBIT
Do not bend the cable by force or leave it under any
heavy object.
• A damaged cable can cause a fire.
PROHIBIT
PROHIBIT
Rev. 1.14
-4-
SRP-770II
CAUTION
Violating following instructions can cause slight wound or damage the appliance.
If you observe a strange smoke, odor or noise from
the printer, unplug it before taking following
measures.
Keep the desiccant out of children’s reach.
• If not, they may eat it.
• Switch off the printer and unplug the set from the mains.
• After the disappearance of the smoke, call your dealer to
repair it.
TO UNPLUG
PROHIBIT
PRINTER
Install the printer on the stable surface.
• If the printer falls down, it can be broken and you can hurt
yourself.
Use only approved accessories and do not try to
disassemble, repair or remodel it for yourself.
• Call your dealer when you need these services.
• Do not touch the blade of auto cutter.
PRINTER
DISASSEMBLING
PROHIBITED
PROHIBIT
PRINTER
Do not let water or other foreign objects in the
printer.
Do not use the printer when it is out of order. This
can cause a fire or an electrocution.
• If this happened, switch off and unplug the printer before
calling your dealer.
• Switch off and unplug the printer before calling your dealer.
PROHIBIT
TO UNPLUG
PRINTER
PRINTER
DEALER
Rev. 1.14
-5-
SRP-770II
■ Other Precautions
The copyright for this user manual and various other manuals is property of the BIXOLON
Co., Ltd. Any copying or conversion into electronic firm and saving of this material
without the express written permission of BIXOLON Co., Ltd. is strictly prohibited.
Use of the information contained in this manual is not subject to any patent liability. This
manual has been prepared with utmost care and attention to detail but may contain certain
errors and/or omissions.
BIXOLON Co., Ltd. is not legally liable for any damages resulting from the use of the
information in this manual.
BIXOLON Co., Ltd. and its affiliates are not legally liable (United States excluded) for any
damages, loss, costs, and/or expenses that result from the breakdown, malfunction, and/or
misuse of the product due to violation or neglect of the operation and maintenance
information and instructions provided by the BIXOLON Co., Ltd., as well as from the
unauthorized alteration, repair, and/or modification of the product by the user and/or third
party.
BIXOLON Co., Ltd. is not legally liable for any damages and/or issues resulting from the
use of options and/or parts that are not authentic BIXOLON products or authorized
products.
Rev. 1.14
-6-
SRP-770II
1. Content Confirmation
The following items should all be contained in the printer package.
Contact the dealer from which the purchase was made if any item is damaged and/or
missing.
SRP-770II
Paper
Power Cord
Cleaning Pen
AC Adapter
CD
User’s Manual
※ Optional items
RS-232C(Serial) Cable
IEEE1284 (Parallel) Cable
USB Cable
Rev. 1.14
-7-
SRP-770II
2. Product Part Names
Feed Button
Power Switch
Cover Peel-off
Cover Lever
Printer Head
Paper Cover
Paper Holder
Paper Gap Sensor
Paper Guide
Peel-off Sensor
Rev. 1.14
-8-
SRP-770II
Fan-Fold
RS-232C Receptacle
Power Receptacle
Dip Switch
IEEE1284 Receptacle
USB Receptacle
SA
Auto Cutter
(Option)
Rev. 1.14
-9-
MS
UN
G
LAB
P
EL
RN
R
TE
SRP-770II
3. Installation & Usage
3-1 Power Connection
Connect power to the printer as shown below.
OFF
Power Switch
AC Adapter
Power Cord
1) Turn off the printer power switch.
2) Check to see that the AC adapter voltage matches that of the power source.
3) Connect the AC adapter jack to the printer power connector.
4) Connect the power cord to the AC adapter.
5) Connect the power cord to a power source/outlet.
Rev. 1.14
- 10 -
SRP-770II
3-2 Interface Cable Connection
Connect the interface cable as shown below.
This printer supports the following communications interface standards.
- RS-232C (Serial)
- IEEE1284 (Parallel)
- USB
USB Cable
RS-232 (Serial) Cable
IEEE1284 (Parallel) Cable
1) Turn off the power switch.
2) Connect the interface cable to the printer interface connector.
- For a Serial cable, secure by tightening the screws on both sides.
- For a Parallel cable, secure by fastening the clips on both sides.
Rev. 1.14
- 11 -
SRP-770II
3-3 Paper Installation
1) Open the Paper Cover.
2) Spread the paper holder and insert
paper as shown.
SU N
SAM
3) Keep note of paper printing direction.
PRI
BEL
G LA
4) Adjust the paper guide to the width of
the paper.
S UN
SAM
5) Close the Paper Cover.
Rev. 1.14
R
NT E
- 12 -
G
EL
LA B
N
PRI
TER
SRP-770II
3-4 LED Display
Feed button
Paper feed or cancel the print job.
LED
The current printer status can be viewed. (Refer to below)
The current printer status can be viewed via the printer’s LED display.
1) Green LED on
- The printer waits for the data from Host (PC) in normal mode.
2) Orange LED on
- It means paper gap sensing error. It becomes on when the printer fails to detect the
paper or paper jam occurred. When fails to detect the paper correctly use
Auto-Calibration function.
3) Red LED on
- The printer has stopped by pressing FEED button. It restarts printing when pressed
again.
4) Green LED blinking
- TPH (Thermal Printing Head) overheated or ;
- The printers is waiting for the button input to run Auto-Calibration function.
5) Orange LED blinking
- No paper. Make sure the paper is loaded correctly.
6) Red LED blinking
- The printer cover is open or ;
- Auto cutter has error such as paper jam in case of auto cutter built-in model.
Rev. 1.14
- 13 -
SRP-770II
4. Self-Test
The self-test checks whether the printer has any problems.
(Users cannot perform this procedure if using the printer’s label peel-off option.)
If the printer does not function properly, contact an authorized dealer.
The self-test checks the following;
1) Make sure that the paper roll has been installed properly.
2) Turn on the power while holding down the FEED button. The self-test begins.
3) The self-test prints the current printer status, which provides the control ROM version
and the DIP switch settings.
4) After the self-test results are printed out:
- No button input within 2 seconds: Normal Print Mode
- Button pressed once within 2 seconds: Hex Dump Mode
- Button pressed twice within 2 seconds: Line Print Mode
* The ESC-POS command set is used in Line Print Mode.
Received data is printed in sequence similar to a receipt printer.
* If it is necessary to set the line mode as the default mode when power is on,
please turn on the dip switches 1-6 and 2-8 together.
ON
Rev. 1.14
- 14 -
SRP-770II
5. Fine Tuning
5-1 Printer Settings with Dip switches
The dip switches are located on the bottom of the printer.
The dip switches are used to set the printer to perform various functions.
Follow these steps when changing dip switch settings:
1) Turn the printer power switch off.
2) Remove the screw on the bottom of the printer and open the bracket.
3) Flip the dip switches using tweezers or another narrow-ended tool.
Switches are off when up and on when down following the figure.
4) New settings take effect when the printer is turned back on.
Rev. 1.14
- 15 -
SRP-770II
[Table 1] Dip Switch 1
No
Functions
1-1
Speed Selection
1-2
1-3
Density Selection
1-4
1-5
Exhibition Selection
1-6
Media Selection
1-7
Auto Cutter
1-8
Back Feed Option
Off
On
4
Off
Off
Off
Off
On
On
On
On
Off
On
Off
On
Off
On
Off
On
[Table 2] Dip Switch 2
No
Functions
2-1
Baud Rate Selection
2-2
2-3
Media Detection
2-4
2-5
2-6
Reserved
Reserved
Reserved
Paper End Sensor
Status
Reserved
2-7
2-8
2
Off
Off
On
On
Off
On
Off
On
Details
4.0 ips
5.0 ips
3
2
Density
Off
Off
13
Off
On
14
On
Off
15
On
On
16
Off
Off
17
Off
On
18
On
Off
19
On
On
20
Normal Mode
Demo Mode
Label Paper
Thermal Continuous Paper
Without Auto Cuter
With Auto Cuter
Back Feeding Enable
Back Feeding Disable
Details
1
Baud Rate
Off
9,600 bps
On
19,200 bps
Off
230,400 bps
On
115,200 bps
Detect Gap
Detect Black-mark
Default --- off
Default --- off
Default --- off
Enable
Disable
Default --- off
5-2 Pause/Restart
Press FEED button to pause at the middle of labels printing.
1) Press FEED once.
2) Printer stops after on-going printing and Red LED becomes on.
3) Press FEED once again. It restarts printing in a queue.
Rev. 1.14
- 16 -
SRP-770II
5-3 Gap Sensor Auto-Calibration
Gap sensor auto-calibration is used when the printer does not detect a gap on the label
paper correctly.
Generally a printer is set to detect most of gap types but sometimes it fails to detect and
keep feeding the paper without a stop when special paper used. In such case, use gap
sensor auto-calibration function for a proper detection.
1) Make sure that paper roll has been installed properly.
2) Turn on the power while holding down FEED button with cover open.
Then the Green LED blinks.
ON
3) Close the ribbon roll and paper cover.
- An information message is printed out and the red LED turns on.
4) Press the paper feed button.
① Once
- The LED color changes to orange.
- The previous gap sensor correction value is erased and reset to its default value.
② Twice
- The LED color changes to green.
- The gap sensor auto-calibration is performed as 2~3 pages of paper are fed
continuously.
5) Gap sensor auto-calibration is complete.
Rev. 1.14
- 17 -
SRP-770II
5-4 Gap Sensor Manual-Calibration
Manual-calibration of media detection can be used when the printer cannot detect a media
gap (or black mark) even after auto-calibration has been executed.
Users can calibrate sensor parameters in detail by using the utility program provided by
the manufacturer.
The utility can be obtained from the enclosed CD or downloaded from the Internet via the
BIXOLON website www.bixolon.com
Please make sure the printer is connected and execute the utility program.
Press the Calibration Setting Manager button after setting the interface type.
1) Select proper values for "No. of detect" and "Detect margin" and press the Execute
Manual Calibration button to make the printer begin media sensor calibration.
2) Typically-used setting values are pre-saved in the Setting buttons (1~8).
3) If the printer malfunctions while executing calibration, please turn off the printer and turn
it on again.
4) The sensor parameters can be set back to factory default settings by pressing the
Cancel Calibration button.
Rev. 1.14
- 18 -
SRP-770II
5-5 The Peel-Off
This function is used to automatically separate labels from the liner.
- The peeler is for Label Paper only.
- When the peeler switch is on, labels are not printed if previous printed labels have
been removed from the peeler.
- When the peeler function is not required, turn the peeler switch off. Keeping the
switch on may result in the printer not working correctly.
- When the peeler switch has been changed, the printer should be turned off and
back on.
1) Open the peel-off cover and turn on the peeler switch. (Check if the peeler LED is on.)
PEEL
ER
OFF
ON
LED
2) Remove the paper and insert the paper through the slot.
Remove
Rev. 1.14
- 19 -
SRP-770II
3) Adjust the paper guides and close the cover.
4) Turn the printer off and back on.
Rev. 1.14
- 20 -
SRP-770II
5-6 Using Fan-Fold Paper
Insert paper through both the rear slot and guides.
Adjust holders and guides to the width of the paper.
OPEN
1) Open the Dust Cover and insert paper.
Dust Cover
3) Adjust Paper Guides and close the
Paper Cover.
2) Adjust Paper Holders to the paper width
and fixed Paper Holders with fixing tool.
Paper Holder
Rev. 1.14
- 21 -
SRP-770II
5-7 Auto Cutter (option)
Auto cutter should be used for continuous paper only. ( i.e. roll paper)
1. Open the Dip switch cover, and make the switch 1 number 7 “On”.
(Refer to printer mode setting at Chapter 5-1.)
2. Put a paper roll into the printer and close the cover.
M
SA
SU
NG
E
LAB
LP
RN
R
TE
※ CAUTION (Partial cut)
Once the printer cut the paper, remove the receipt in order for next printing.
Otherwise the receipt could be back into the printer and the cutter would cut it again.
Rev. 1.14
- 22 -
SRP-770II
6. Cleaning Head
Paper dust on the heating elements may lower the printer quality.
When dirty, clean the print head as follows:
※ CAUTION
- Make sure to turn the printer power off prior to cleaning.
- As the print head gets very hot during printing, if intending to clean the print head,
turn the printer power off and wait approximately 10 minute before commencement.
- When cleaning the print head, take care not to touch the heated portion of the print
head.
→ The print head is susceptible to damage from static electricity, etc.
- Take care not to allow the print head to become scratched and/or damaged in any
way.
1) Open the paper cover and remove paper and ribbon.
2) Wipe the print head with a cleaning pen.
3) Use a cloth moistened with an alcohol solution to clean the paper sensor are and
remove any paper remnants and/or dust.
4) Insert paper into the printer 1~2 minutes after completing the cleaning process and
close the printer cover.
※ Perform the cleaning process each time the paper roll is replaced to prevent print
quality deterioration.
Rev. 1.14
- 23 -
SRP-770II
7. Appendix
7-1 Specifications
Printer
Paper
AC
Adapter
Usage
Conditions
Item
Printing Method
Dot Density
Printing Width
Printing Speed
Roll
Fan-Fold Type
SMPS Input Voltage
Frequency
SMPS Output Voltage
Temperature
Humidity
(except for paper)
Description
Thermal Transfer / Direct Thermal Printing
203 dpi (8 dot/mm)
25.4 ~ 104 mm
127 mm/sec
38.1 ~ 106mm
45 ~ 112 mm
AC 100~240V
50/60 Hz
DC 24V
0 ~ 45 ℃ (Operating)
-25 ~ 70 ℃ (Storage)
30 ~ 80 % RH (Operating)
10 ~ 90 % RH (Storage)
※ Note
Printing speed can vary depending on the data transmission speed and combination of
control commands.
Rev. 1.14
- 24 -
SRP-770II
7-2 Certification
1) EMC & Safety Standards
• Europe: CE EMC,CB-Scheme:IEC60950-1, GS: EN60950-1: 2001
• North America: FCC rules parts 15B
WARNING
Use of an unprotected interface cable with this printer conflicts with EMC standards.
Users should only use cables approved by BIXOLON.
2) CE Mark
• EMC Directive 89/336/EEC
EN55002:1994+A1:1995+A2:1997
EN55024:1998+A1:2001+A2:2003
EN61000-3-2:2000
EN61000-3-3:1995+A1:2001
EN6100-4-2:1995+A1:1998+A2:2001
EN6100-4-3: 2002+A1:2002
EN6100-4-4:2004
EN6100-4-5:1995+A1:2001
EN6100-4-6:1996+A1:2001
EN6100-4-8:1993+A1:2001
EN6100-4-11:1994+A1:2001
• Low Voltage Directive 73/23/EEC
Safety: EN60950-1:2001
3) WEEE (Waste Electrical and Electric Equipment)
This mark shown on the product or its literature indicates that the
corresponding item should not be discarded at the end of its working life with
other household waste. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate marked
items from other types of waste and recycle them responsibly to promote the
sustained reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office for details
of where and how they can conduct environmentally safe recycling of such items.
Commercial users should contact their suppliers and check the terms and conditions of
purchase contracts. This product should not be combined with other commercial
waste for disposal.
7-3 Label Types
The label types used with this printer are as follows.
• Control Labels: PC
• Other Labels: PET
Rev. 1.14
- 25 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising