Instruction Manual
IMPORTANT SAFEGUARDS
STEREO RADIO CASSETTE RECORDER
COMPACT DISC PLAYER
GPS213PLLR
Instruction Manual
PRE FITTED MAINS PLUGS
For your convenience a mains plug has been fitted to this appliance. For your safety please
observe the following information.
1. Should the fuse in the plug remove the plug from the wall socket and replace the fuse with a 3
Amp ASTA approved to BS 1362 fuse.
2. Never use the plug without the fuse cover fitted. Replacement fuse covers are available from
your dealer or most electrical retail outlets.
3. If the mains plug is cut off the cable, rewire the replacement plug in accordance with
instruction given in this manual.
4. CAUTION: Under no circumstances should the discarded plug be inserted mains socket. To
prevent a shock hazard carefully dispose of the discarded plug. Do not leave the plug lying
around where children might see it.
WARNING: To prevent fire or shock hazard do not expose this unit to rain or moisture.
CAUTION: DANGEROUS VOLTAGES EXIST INSIDE THIS UNIT, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL. DISCONNECT FROM MAINS SUPPLY
WHEN NOT IN USE.
PLUG WIRING DETAILS
E
BLUE
N
L
FUSE
BROWN
CORD
GRIP
The wires in this mains lead are coloured in
accordance with the following wiring codes:
Blue................................................. Neutral
Brown................................................... Live
The wires in this mains lead must be
connected to the terminals in the plugs as
follows:
Blue Wire..................................... N or Black
Brown Wire..................................... L or Red
Only a 3 Amp fuse should be fitted in the plug
or a 5 Amp fuse at the distribution board.
WARNING: UNDER NO CIRCUMSTANCES MUST THE LIVE OR NEUTRAL WIRES BE
CONNECTED TO THE EARTH TERMINAL IN A 3-PIN MAINS PLUG.
SPECIFICATIONS
Programme Play ............................................Up to 20 tracks
This symbol means that this unit is double insulated.
An earth connection is not required.
Earphone output ............................................20mW x 2 (32 )
Power requirement ........................................AC 230V/50Hz
Dimension .....................................................Approx. 310 (L) x 231.2 (W) x 127.7 (H) mm
Weight ...........................................................Approx. 2.044Kg (not including batteries)
HELPLINE PHONE NUMBER 0870 873 0080
For improvement purposes, specification and design are subject to change without notice.
Goodmans Product Information Helpline 0870 873 0080
CAUTION
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
Use of Controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
LASER SAFETY
This unit employs a laser, only qualified service personnel should attempt repair.
DANGER: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCK FAILED OR DEFEATED. AVOID DIRECT
EXPOSURE TO BEAM.
CAUTION: HAZARDOUS LASER RADIATION WHEN OPEN AND
INTERLOCK DEFEATED.
CAUTION
CLEANING: Always disconnect unit from mains supply before attempting to clean it. Use soft
cloth moistened with soapy water, wipe gently. Do not use solvents or abrasive
materials.
SOME DO'S AND DONT'S ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet European safety standards but
like any electrical equipment, care must be taken if you are to obtain the best results and safety is
to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (Including the mains plug, extension leads and
interconnections between pieces of equipment) are properly made in accordance with the
manufacturer's instructions. Switch off and withdraw the mains plug when making or changing
connections.
Do consult your dealer if you are ever in doubt of the installation, operating, or safety of your
equipment.
Don't continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way- switch off, withdraw the mains plug and consult your dealer.
Don't remove any fixed covers as this may expose dangerous voltages.
Don't leave equipment switched on when it is unattended unless it is specifically stated that it is
designed for unattended operation or has a standby mode. Switch off using the switch on the
equipment and made sure that your family knows how to do this. Special arrangements may need
to be made for infirm or handicapped people.
Don't listen to headphones at high volume, as such use can permanently damage your hearing.
Don't obstruct the ventilation of the equiment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
Don't allow electrical equipment to be exposed to rain or moisture.
Above all
Never let anyone, especially children, push anything into holes, slots or any other opening as
this could result in a fatal electric shock.
Never guess or take chances with electrical equipment of any kind.
It is better to be safe than sorry!
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE, DANGEROUS HIGH VOLTAGES ARE
PRESENT INSIDE THE ENCLOSURE, DO NOT OPEN THE CABINET, REFER
SERVICING TO QUALIFIED PERSONNEL ONLY.
HELPLINE PHONE NUMBER 0870 873 0080
Your hearing is very important to you and to us so please take care when operating
this equipment. The following guidelines are provided for your information.
ESTABLISH A SAFE SOUND LEVEL
— Over time your hearing will adapt to continuous loud sounds and will give the
impression that the volume has in fact been reduced. What seems normal to
you may in fact be harmful. To guard against this BEFORE YOUR HEARING
ADAPTS set the volume at a low level.
— Slowly increase the level until you can hear comfortably and clearly and without
distortion.
— Damage to your hearing is accumulative and is irreversible.
— Any ringing or discomfort in the ears indicates that the volume is too loud.
— Remember listening for prolonged period of time at high volume levels will
harm your hearing.
Once you have established a comfortable listening level, DO NOT INCREASE
THE SOUND LEVEL FURTHER.
The following list of typical sound levels may assist you in recognizing just how
loud you have set the volume level.
DECIBEL
Level dB
Example
30dB
40
50
60
70
Quiet library, soft whisper.
Living room, fridge freezer bedroom away from traffic.
Normal conversation, quiet office, light traffic.
Electric sewing machine.
Vacuum cleaner, hair dryer, noisy restaurant.
THE FOLLOWING NOISE CAN BE HARMFUL UNDER CONSTANT EXPOSURE
80dB
90
100
120
140
180
Average city traffic, alarm clock buzzer at 1 Metre, food mixer.
Motorcycle, heavy goods vehicle, petrol lawn mower.
Pneumatic drill, chain saw, garbage truck, discotec/night-club.
Rock band concert, thunderclap, fast train passing by.
THRESHOLD OF PAIN Gunshot, jet plane taking off.
Rocket Launching pad.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Power Sources ................................................. 1
Player Maintenance............................................ 2
Disc Cleaning, Power failure............................ 3
1. As the laser beam used in this compact
disc player is harmful to the eyes, do not
attempt to disassemble the casing.
Player Operation
Location of Controls........................................... 4
Radio operation................................................. 5
Listening to a compact disc.................................. 6
Program play operation......................................7
Repeat play operation.........................................8
Random play operation........................................9
Cassettes..........................................................10
Recording from Radio/MIC/CD........................... 11
Remote Control.................................................12
Product Specifications...................................... 13
WARNING
2. Stop operation immediately if any liquid or
solid object should fall into the cabinet.
Unplug the unit and have it checked by
qualified personnel.
3. Do not touch the lens or poke at it. If you do,
you may damage the lens and the player
may not operate properly.
1. POWER SOURCES
AC MAINS OPERATION
BATTERY OPERATION
1. Remove the AC cord which is packed
inside the box.
2. Connect the cord to the AC input
socket.
3. Connect the 3 pin mains plug to an AC
mains socket.
1. Insert 8 LR14 (C Size) batteries (not
supplied) into the battery compartment
observing the correct polarity as
indicated.
2. Ensure compartment cover is securely
fitted.
3. Product will only function from
batteries once AC cord is removed
from the unit.
4. When replacing flat batteries, ensure
all batteries are replaced at the same
time with the same type.
5. If the product is not to be used for an
extended period of time the batteries
should be removed to prevent any
possible damage to the product.
4. Do not put anything in the safety slot. If you
do, the laser diode will be ON when the lid
is still opened.
5. This unit employs a laser. The use of
controls or adjustments or performance of
procedures other then those specified
herein may result in exposure to
hazardous radiation.
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
2. PLAYER MAINTENANCE
CASSETTE DECK MAINTENANCE
CLEANING THE LENS
When the heads, capstan and pinch roller
become dirty, this may result in muffled,
distorted or reduced sound during play back
and may even result in tape jams.
Clean the tape head with a head cleaning
tape.
If the lens in the CD pick-up is dirty, dusty,
etc, it could degrade the sound or prevent
disc play. Open the disc holder and clean
the lens as shown.
h Use a blower (available from camera
stores) to blow dust off the lens.
h If there are fingerprints, etc., on the
lens, gently wipe clean with a cotton
swab.
3. DISC CLEANING, POWER FAILURE
4. LOCATION OF CONTROLS
Cleaning the Disc
3
2
1. To handle a disc use only one of the two
manners illustrated.
NOTE: Do not touch the rainbow-colored
side.
2. To wipe a disc, use only a soft cloth. Do
not use benzene or thinner which will
damage the disc. The disc should always
be wiped in a straight line from the center
to the edge. It should never be wiped in a
circular motion.
4
5
6
7
8
9
10 12 14 16
11 13 15 17
1
18
3. Never place the disc on other equipment
or near any heat source. Avoid positions
where the disc would be subjected to
direct sunlight for long periods.
19 33 21
Maintenance and care
1. Electronic products should never be
subjected to extreme temperatures nor
high humidity to ensure good performance
and a long life-time. The player should not
be placed in bathing areas, or around
stoves and radiators, etc. Always leave
sufficient space around the unit for
ventilation.
2. If necessary, only clean the cabinet of the
unit with a soft dampened piece of cloth.
(be sure the AC power cord is unplugged
from the outlet) Never use a polish or a
strong detergent for cleaning since this
can damage the finish of the cabinet.
22
24 26 28 30
23 25 27 29
31
20
22
32
34
35
36
37
42
43
44
45
46
47
38
39
40
48
41
1. HEADPHONE JACK
2. HANDLE
3. CD DOOR
4. VOLUME UP/DOWN BUTTON
5. POWER BUTTON
6. BUILT-IN CONDENSER MICROPHONE
7. CASSETTE PAUSE BUTTON
8. CASSETTE STOP/EJECT BUTTON
9. CASSETTE FAST FORWARD BUTTON
10. CASSETTE REWIND BUTTON
11. CASSETTE PLAY BUTTON
12. CASSETTE RECORD BUTTON
13. CD DOOR OPEN BUTTON
14. BAND BUTTON
15. RADIO BUTTON
16. TAPE BUTTON
17. CD BUTTON
18. FM STEREO/MONO SWITCH
19. STAND BY INDICATOR
20. BATTERY COMPARTMENT
21. LCD DISPLAY
22. SPEAKERS
23. CASSETTE DOOR
24. CD RANDOM BUTTON
25. RADIO PRESET/CD REPEAT BUTTON
26. CD PROGRAM/ RADIO STORE BUTTON
27. CD BACKWARD SKIP/SEARCH / RADIO
TUNING DOWN BUTTON
28. CD FORWARD SKIP/SEARCH / RADIO TUNING
UP BUTTON
29. CD STOP BUTTON
30. CD PLAY/PAUSE BUTTON
31. TELESCOPIC ANTENNA
32. AC SOCKET
33. REMOTE SENSOR
REMOTE CONTROL
34. MUTE BUTTON
35. CD BUTTON
36. CD PROGRAM/RADIO STATION STORE
BUTTON
37. VOLUME DOWN BUTTON
38. CD PLAY/PAUSE BUTTON
39. CD BACKWARD SKIP/SEARCH / RADIO
TUNING DOWN BUTTON
40. CD STOP BUTTON
41. BATTERY COMPARTMENT
42. POWER BUTTON
43. RADIO BUTTON
44. BAND BUTTON
45. CD REPEAT/RADIO PRESET BUTTON
46. TAPE BUTTON
47. VOLUME UP BUTTON
48. CD FORWARD SKIP/SEARCH / RADIO TUNING
UP BUTTON
5. RADIO OPERATION
1. Turn the power on by pressing the
Power button.
PRESETTING STATIONS
UP TO 10 MW AND 10 FM STATIONS CAN BE STORED INTO THE PRESET
MEMORIES. (THEY WILL REMAIN IN MEMORY AS LONG AS THE AC POWER CORD
IS CONNECTED.)
1. Press the Band button to select MW or
FM band, and press the Tuning Down
or Up button to select a station.
2. Press the RADIO button to select radio.
3. Press the Radio Band button to select
the desired wave band.
4. Tune to desired station by pressing the
Tuning Down or Up button. Each time the
button is pressed, the frequency
changes.
5. To search for a station quickly (automatic
tuning), keep the Tuning Down or Up
button pressed until the station starts to
change rapidly, then release the button
and it will stop at the next strong station.
6. If you tune into a FM stereo station,
" FM STEREO " will show in the display.
If when you are listening to a station with
the FM Stereo/Mono switch set to Stereo
and there is a large amount of noise (hiss).
Change the FM Stereo/Mono switch to
the Mono position. If you are listening to
an MW station, rotate the unit until clear
reception is heard.
7. Press the Volume Up/Down button to
your listening preference.
8. To turn off the radio, press the Power
button again, the Stand-by indicator will
be on.
2. Press the PROG button, "
flash in the display.
" will
3. While the "
" is blinking, Press the
Preset/Repeat button to choose a
memory location (01- 10). (Example:
Push the Preset/Repeat button 3 times
for Preset Number 3; 4 times for Preset
Number 4.)
4. Pressthe PROG button again to confirm.
The station now broadcasting is stored
into that preset memory.
NOTE: Steps 2-4 should be done
quickly.
5. Repeat the above steps 1 to 4 to store
other stations into memory.
6. Each memory location (01-10) can store
2 stations, one for MW, the other for FM.
TO LISTEN TO A PRESET STATION
(after you programmed them)
1. Press the Power button, the Stand-by
Indicator will be off.
2. Press the RADIO button to select radio.
3. Press the Band button to select your
desired wave band.
4. Press the Preset/Repeat button to select
the memory location (01-10). You will
receive the station you stored into that
preset memory. Pressing the button
several times will give you the different
preset stations you stored into the preset
memories 1 to 10 (Example: Pressing
the button 3 times will give you Preset
Number 3, press the button 4 times will
give you Preset Number 4). Preset
Number will show in the display.
5. To turn off the radio, press the Power
button again, the Stand-by Indicator will
be on.
6. LISTENING TO A COMPACT DISC
PLAYING A COMPACT DISC
This set is designed to play only compact
discs bearing this
identification logo
(logo must say DIGITAL AUDIO).
1. Press the Power button.
2. Press the CD button to select CD mode.
3. Press the CD Door Open button to open
the CD Door.
4. Insert a CD with the LABEL side facing UP,
close the CD Door by gently pushing it
down.
5. The display will show " ", and the total
number of tracks and the total play time
of the disc. (If the disc is upside down or
damaged, the display will show "
",
and then "
" will be shown).
6. To start the music, press the CD
Play/Pause button (wait a few seconds
for music to start). The first track number
"
" will appear in the display, and the
disc will start playing. The elapsed time
shows in the display.
7. Press the Volume Up/Down button to
adjust the volume.
8. To p a u s e p l a y b a c k , p r e s s t h e
Play/Pause button, the elapsed time will
flash to remind you that you are in pause
mode.
9. To resume the music from pause, press
the Play/Pause button again. The
elapsed time will be steady on (not
flashing).
10. To stop playing music, press the CD
Stop button.
11. To turn off the unit, press the Power
button again, and the Stand-by indicator
will be on.
5. Repeat steps 3 and 4 until all the desired
tracks are programmed.
6. When you have finished programming,
press the CD Play/Pause button.
7. All songs will play in the order you
programmed.
8. The display will show the track number
being played, and the "
" will
show (but not flashing) in the display
during programmed play.
9. If in middle of play, you want to hear the
next programmed song, press Forward
Skip/Search button.
10. When all the songs have finished playing,
the set will stop. "
" disappears
from the display.
11. To turn off the power, remember to press
the Power button again, the Stand-by
indicator will be on.
NOTE: Programming can only be done
when the CD is in the stop mode.
SKIPPING TRACKS (SEARCH)
1. This function enables you to find the
beginning of any desired track during
play. If the CD Forward Search/Skip (
)
button is pressed once or repeatedly, the
NEXT TRACK or one of the following
tracks will be selected. The Display will
show the track or song number.
2. If the CD Backward Search/Skip (
)
button is pressed twice or more in rapid
succession, play will go BACK one track
per press.
3. When the unit is in the pause mode, it is
also possible to select the beginning of a
certain track by using the CD Forward
Search/Skip (
) button and CD
Backward Search/Skip (
) button to
reach the desired track. After selection,
press CD Play/Pause button.
4. Press and hold the CD Forward
Search/Skip (
) button to search
forward at a high speed for a particular
point of a song. Press and HOLD the CD
Backward Search/Skip (
) button to
search backward. Release the button to
resume normal play when the point is
found.
8. REPEAT PLAY OPERATION
REPEAT PLAY SINGLE SONG
7. PROGRAM PLAY OPERATION
PROGRAMMED (MEMORY) PLAYBACK
(up to 20 tracks can be programmed)
1. During STOP mode, press the
Program/Store button.
2. The display will show "
" and
"
".
3. Press the Skip/Search buttons
either
or
until the desired track
shows on the display.
4. Press the Program/Store button. The
display will show "
".
x2
To repeat the SAME song over and over
again, do the following:
1. Press the Preset/Repeat button once
during playback or stop mode.
2. The " REPEAT " icon will be flashing. The
song currently playing will play over and
over, till you press Stop button.
3. To stop the repeat function, press the
Repeat button twice.
REPEAT PLAY ALL SONGS
TO PLAY A CASSETTE TAPE
To repeat play ALL SONGS on a disc and
then play them again and again.
1. Press the Preset/Repeat button twice
during playback or stop mode.
2. The " REPEAT " icon will show steadily
(not flashing) in the display. All the
songs on the CD will play in order and
then start all over again. (In stop mode
pressing the PLAY/PAUSE button again
is required.)
3. To stop the repeat function, press the
Repeat button once.
1. Open the Cassette door by pressing
the Cassette Stop/Eject button (in
some cases, you may have to press
the Cassette Stop/Eject button twice
since this button has combined
functions).
2. Insert cassette tape into deck door
track. Make sure the full reel is on the
right and the exposed part of the tape
faces upward, make sure the tape
inside is not slack or loosely wound. If it
is, insert a pencil into the reel and turn
until the tape is wound up.
3. Close the Cassette door.
4. Press TAPE button.
5. Press the Cassette Play button.
NOTE: If the Play button pops up, turn
the tape over or press Rewind button.
6. Press the Volume Up/Down button to
your listening preference.
7. To stop the tape, press the Cassette
Stop/Eject button.
8. To remove the cassette, press the
Cassette Stop/Eject button again and
the Cassette door will open.
Unload the cassette tape, turn it over and
re-insert into cassette compartment if you
want to play the other side of the cassette
tape.
x1
9. RANDOM PLAY OPERATION
Press the random button during CD
playback or in the CD stop mode, and
then press the play/pause button. The unit
will pick up the tracks in a random order
for playback.
10. CASSETTES
CASSETTE TAPE SELECTION
AUTOMATIC LEVEL CONTROL (ALC)
The quality and condition of the cassette tapes you use will have a direct effect on the
performance of this set.
Low quality tapes tend to break and stretch and a broken tape can easily become entangle
in the drive mechanism, causing major damage. Stretched tapes will run at uneven speeds
and will distort anything recorded on them.
h Use only well-known brands of tapes.
h Use of C-120 (120 minutes) cassette is not recommended. The extreme thinness of
this tape may result in breakage or other failures.
h This set is not designed for CrO2, Fe-Cr or METAL tape use. Therefore, be sure to use
named brand normal cassette tapes.
This product utilizes the latest Automatic
Level Control circuitry, therefore, it is not
necessary to adjust the Volume Control
when recording. This circuit automatically
records at the correct level and prevents
over loading.
NOTE: While recording you may adjust
the Volume Control as desired
without affecting the recording
operation.
11. RECORDING FROM RADIO/MICROPHONE/CD
RECORDING FROM RADIO
1. Follow the instructions to listen to the
radio.
2. Press RADIO button.
3. Load a blank cassette tape with full
spool on right into the door.
4. Locate the portion of the tape where
you desire to start recording by using
the Rewind feature (or Fast Forward)
or start at the beginning of the tape.
5. Tune in to the station you want to
record, press the Cassette Record
button and Cassette Play button
simultaneously. Both buttons should
remain in their depressed positions
when released. Also, pressing the
Cassette Record button alone, will also
cause the Cassette Play button to go
down. This is the new one-touch
recording feature.
6. You are now recording from the Built-in
Radio and the recording process will
automatically stop at the end of the
tape.
7. To stop the recording manually, press
the Cassette Stop/Eject button.
NOTE: When you want to play the
cassette tape after recording,
p r e s s TA P E b u t t o n , p r e s s
Cassette Rewind button, and then
press Cassette Play button. Press
the Volume Up/Down button to
your taste.
RECORDING FROM THE BUILT-IN
MICROPHONE
1. Load a blank cassette tape into the
Cassette door (full reel or spool on right
side).
2. Press TAPE button.
3. Press the Cassette Record button and
Cassette Play button at the same time.
Both buttons should remain in their
down positions when released.
4. When you talk in front of the set your
voice will be recorded. You are now
recording using the Built-in Condenser
Microphone and the recording process
will automatically stop at the end of the
tape and shut itself off.
5. To stop the recording manually, press
the Cassette Stop/Eject button.
6. To hear what you recorded, press the
Cassette Rewind button and Cassette
Play button.
RECORDING FROM A CD
1. Load the cassette tape into the
Cassette Door (full reel on the right ).
2. Load the compact disc and close the CD
Door.
3. Press CD button.
4. Press the Cassette Pause button.
5. Press the Cassette Record button for
record stand by.
NOTE: When pressing the Cassette
Record Button, the Cassette
Play Button will automatically
go down (If the buttons do not
go down, reverse the tape or
check record lever interlock).
6. Start the CD playing by pressing the CD
Play/Pause button.
7. Press (and release) the Cassette Pause
button when you wish to start recording.
8. Press the Cassette Stop/Eject button to
stop the recording.
9. The recording will stop when the tape
has reached the end and the Record
and Play buttons will pop up.
10. To hear what you recorded, press TAPE
button, press Rewind and Play button.
11. To shut off the set, press Stop on the
Cassette Deck. Press Power button, the
Stand-by indicator will be on.
13. PRODUCT SPECIFICATIONS
PICK-UP
System
Compact disc digital audio system
Laser diode
Properties
material: GaAIAs
Wavelength: =780nm
Emission Duration: continuous
Laser output: <44.6 W
Cross-interleave Reed-solomon code
Error correction
AUDIO
D/A conversion
Frequency response
1-bit DAC 8 times oversampling
Wow and flutter
No. of channels
Output level
Below measurable limits
2 channels (stereo)
Earphone: 20mW (32 )
Speakers Impedance
8
20-20,000Hz (+1/-3 dB)
3W*2
12. REMOTE CONTROL
RADIO
REMOTE OPERATION
INSERTING BATTERIES
Receiving bands
MW/FM
By using the remote controller, you can
operate the system in almost the same
way as with the controls of the main unit.
1. Open the battery compartment cover.
2. Install 2pcs UM-4 (size AAA) batteries
into the battery Compartment matching
the polarity as shown in the battery
compartment.
3. Close the battery compartment lid.
NOTE: Always remove batteries if the
remote controller is not going to
be used for a month or more.
Batteries left in the unit may
leak and cause damage.
Frequency range
MW
FM
MUTE BUTTON
The unit can mute during CD, Radio,
Cassette playing. When you have a call
or do not want to listen the music, you can
press the MUTE Button on remote
controller, then there will be no sound.
Press the MUTE Button again, and the
music will resume.
REMOTE CONTROL RANGE
Use the remote control within an angle of
30o at the left and right horizontally and
over distances up to about 3 meters.
540-1600
88 - 108
KHz
MHz
GENERAL
Power requirements
AC 230V
DC 8* "C" size (or equivalents) batteries
Power consumption
12.5W
Approx. 310 (L) x 231.2 (W) x 127.7 (H) mm
Approx. 2.044Kg (not including batteries)
Dimension
Net Weight
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement