The biggest thing in signal conditioning is only 6 mm wide

The biggest thing in signal conditioning is only 6 mm wide
The biggest thing
in signal conditioning
is only 6 mm wide
PERFORMANCE
MADE
SMARTER
3000 series
High performance temperature
transmitters and signal devices
T E M P E R AT U R E | I . S . I N T E R FA C E S | CO M M U N I C AT I O N I N T E R FA C E S | M U LT I F U N C T I O N A L | I S O L AT I O N | Your supplier:
JSP, s.r.o., Raisova 547, 506 01 Jičín, Czech Republic
Phone: +420 493 760 811, Fax: +420 493 760 820, e-mail: [email protected]
JSP Industrial Controls
www.jsp.cz
The cost-effective 3000 series
equipped with patented technologies
Everything you need to perform – without compromise
Operating a precise, efficient process
requires much more than just an
accurate temperature transmitter
or signal device. And with PR
electronics’ unique 3000 series, you get
high accuracy, fast response time
AND low temperature drift in just
6 mm. Our 3000 series provides
exceptional performance for dedicated
applications at a much lower total cost
of ownership.
The 3000 series is equipped with many approvals for applications worldwide.
C O M M U N I C AT I O N F O U N D AT I O N
High accuracy
• High basic 0.05% accuracy in all
available signal ranges for reliable
signals you can trust
• All units tested to ensure 2.5 kVAC
isolation and have excellent noise
immunity
• NAMUR NE21 burst A criteria
Fast response time
• Transmits rapid changes in process
measurements to your PLC/DCS for
fast and accurate monitoring of
critical signals
• Response time of < 5 / < 7 ms (> 100 Hz
signal band width) for analog signals,
< 30 ms for temperature measurements
and < 60 ms for HART signals
• Accurate measurement of rapidly
changing signals from torque,
acceleration and thermocouple
temperature sensors
Low temperature drift
• Low temperature coefficient better
than 0.01% / °C in a wide -25 to +70°C
ambient temperature range for
precise measurements
• Long term accuracy better than 0.1% /
3 years with no need for re-calibration
Temperature devices
Accurately converting temperature signals to analog or digital, now with
HART® technology
Temperature transmitters and converters have been our core business for
four decades, and now this expertise
extends to the 6 mm 3000 series.
This wide range of high-performance
temperature devices offers you
reliable and accurate conversion of
industry process temperature signals
to analog or digital outputs. The easy
DIP-switch set-up allows for more than
1000 different pre-calibrated temperature range combinations.
Unique additional features
Never seen before in a 6 mm series,
the sensor error detection is conducted
simultaneously without disrupting the
temperature measurement or response
time.
The 3113 and 3337 devices even offer
HART 7 protocol.
3102: Cost-effective Pt100 transmitter
3101: Cost-effective TC transmitter
• Converts TC J and K temperature sensors to
voltage or current outputs
•H
igh accuracy, better than 1°C or 0.1% in all
available ranges
•S
electable < 30 ms / 300 ms response time
•E
xcellent EMC performance and 50/60 Hz
noise suppression
3111: High performance TC transmitter
•C
onverts TC J and K temperature sensors to
voltage or current outputs
• Top performance in harsh EMC environments
•M
eets the NAMUR NE21 recommendations
reater than 0.5°C or 0.05% accuracy in all
•G
available ranges
•H
igh galvanic isolation of 2.5 kVAC
• Converts Pt100 temperature sensors to
voltage or current outputs
• Over 1000 pre-calibrated temperature
ranges selectable
• High accuracy, better than 0.2°C or 0.1%
in all available ranges
• Easily configurable via DIP-switches
3112: High performance Pt100 transmitter
• Converts Pt100 temperature sensors to
voltage or current outputs
• Excellent accuracy, better than 0.1°C or
0.05% in all available ranges
• Pre-calibrated temperature ranges
selectable via DIP-switches
• Selectable < 30 ms / 300 ms response time
• High galvanic isolation of 2.5 kVAC
3114: Multifunctional converter
3113: HART® Temperature transmitter
• Converts Pt100, TC J and K temperature
sensors to an isolated active analog current
and HART signal output
•M
ultiple pre-calibrated temperature ranges
selectable
•P
rogrammed by DIP-switches or by
standard HART interface
• Converts RTD, TC, Ohm, potentiometer,
mA or voltage input signals
• All operational parameters can be modified
to suit almost any signal conversion
• High performance, flexible design
• P rogramming via 4501 display and
Configmate 4590
C O M M U N I C AT I O N F O U N D AT I O N
3331: Loop powered temperature transmitter
•C
onverts Pt100, TC J and K temperature
sensors to an isolated passive 4-20 mA
current output
•G
reater than 0.1°C or 0.05% accuracy in
all available ranges
lexibly loop powered by 5.5-35 VDC
•F
•H
igh galvanic isolation of 2.5 kVAC
3337: HART® Loop powered temperature transmitter
• Converts Pt100, TC J and K temperature
sensors to an isolated passive current output
• Loop powered 4-20 mA output with HART
protocol
• More pre-calibrated temperature ranges are
selectable
• Programmed by DIP-switches or by standard
HART interface
C O M M U N I C AT I O N F O U N D AT I O N
3333: Loop powered Pt100 transmitter
• Converts a standard 2, 3 or 4-wire Pt100
temperature sensor
• Provides a passive analog current
output signal
• Flexibly loop powered by 3.3-35 VDC
• Wide ambient temperature range of
-25 to +70°C
Signal devices
Provides exceptionally high, safe isolation between
the input, output and supply
Inside our slim 6 mm housing, this range
of intelligent signal devices provides you
with exceptionally high, safe isolation,
no matter the signal. Easily DIP-switch
or 4501 display (3114) programmable,
all of our signal devices offer extremely
high isolation levels of 2.5 kVAC and
exceptional EMC performance.
These high-performance devices
utilize our innovative microprocessor
technology to provide high base
accuracy, low power consumption,
and maximum protection against
error due to electromagnetic noise.
3103: Isolated signal repeater
• Isolation and 1:1 conversion of standard
current signals
• Simple and cost effective
• Fast response time: < 7 ms
• Conversion range: 0-20 mA
3105: Cost-effective isolation converter
• Isolation and conversion of standard analog
process signals
• Ultra low cost
• Fast response time: < 7 ms
• DIP-switch configured
3109: Signal converter / splitter
• Isolation and conversion of standard active/
passive current and voltage process signals
• Splitter function: 1 in – 2 out, each
individually configurable
• Easy and fast DIP-switch programming for
input and individual output set-up
• Loop supply > 17 V for powering 2-wire
transmitters
3117: Bipolar isolated converter
• Converts bipolar voltage or current process
signals to unipolar output signals
• Multiple ranges are selectable via DIP-switch
• High 0.05% accuracy in all available ranges
3185: Loop powered isolator
• 1- or 2-channel input loop powered isolator
• Signal 1:1 functional range 0-23 mA
• Galvanic isolation of current loop signals
• Competitive in terms of both price and
technology
3104: Flexible signal isolator and converter
• Isolation and conversion of standard active/
passive current and voltage process signals
• 0.05% accuracy in all available DIP-switch
selectable ranges
• Loop supply > 17 V for powering 2-wire
transmitters
3108: Isolated signal splitter and repeater
• Isolation and signal repeating of 0-20 mA
and 4-20 mA current signals
• Provides simple splitter function:
1 in – 2 out
• High accuracy < ±0.05% of span
• Fast response time: < 7 ms
3114: Multifunctional converter
• Conversion/isolation of analog signals
for multiple applications
• Measures 2, 3, or 4-wire RTD, TC, linear
resistance, potentiometer, current or
voltage inputs
• Programming via 4501 display and
Configmate 4590
3118: Bipolar isolated converter/splitter
• Converts bipolar voltage or current process
signals to 2 unipolar outputs or 1 bipolar
output
• Fast response time: < 7 ms or < 44 ms
• Conversion range: ±20 mA or ±10 V
3186: 2-wire transmitter isolator
• 1:1 transmitter isolator with 2 wires
• Excellent accuracy in the range of 3.5-23 mA
• 1- or 2-channel versions
• 100 channels in just 30 cm
More advanced features
in one compact device
All the reliable, flexible and user-friendly features
you need for top performance
Our ingenious 6 mm range enables you to have upwards of 50 units or 100 channels
in just 30 cm.
Power supply
The separate power devices can be energized by
16.8-31.2 VDC, and the output loop powered devices
can be energized by 3.3-35 VDC. This flexibility
provides high immunity to power dropouts and
surges.
Mounting
Devices can be mounted both vertically and horizontally with no air gap separation required. The devices
snap onto a power rail or DIN rail and are easily
detached by lifting the bottom lock.
Side labels
All information relevant to installation and
DIP-switch setting is printed on the sides of
the housing for easy visibility.
DIP-switch programming
Re-calibration is not needed after changing the
DIP-switch range settings. Just change the DIP-switch,
cycle the power to the unit and obtain the new,
pre-calibrated I/O range. HART programming is enabled
for selected devices.
High level of isolation
Safe galvanic isolation of 2.5 kVAC provides high
noise immunity and prevents ground loops for
accurate delivery of the process signal to your
control system.
Device status indicators
A front LED indicates device status, e.g. an error in
the set-up, sensor or hardware.
Power rail
Most of the devices can be energized on a power rail,
enabling redundant power supplies and hot swapping.
The 3405 and 9410 power connectors allow for easy
connection of a 24 VDC source to the power rail.
Over voltage- / polarity protection
All terminals can withstand up to ±31.2 VDC, and
are protected against incorrect supply wiring to
ensure safe, error-free installation.
Vibration test
Devices are vibration tested up to 4g via DNV and
GL according to IEC 60068-2-6. The 9404 module
stop provides additional support in heavy vibration
applications, e.g. marine.
Ambient temperature range
As temperature changes in your control panel,
our units offer a low temperature coefficient
(better than 0.01% / °C) over a wide temperature
range of -25 to +70°C.
Raising the bar
Unique, patent-pending, state-of-the-art
technology gives you a competitive advantage
Since 1974, we have been setting the benchmark, developing new and better
standards within signal conditioning. And with the new 3000 series, we have
done it again.
Patent for:
Sensor error/wire breakage
detection
A method of continuous surveillance
has been developed to ensure
responsive sensor error/wire
breakage detection, as well as
extremely fast signal measurement.
It is based on a continuous out-offrequency band measurement of the
connected sensor’s impedance.
Patent for:
Power supply with spread
spectrum to reduce wire-­
conducted emissions
A traditional high frequency switch
mode power supply causes wire
conducted emissions. However,
continuous changing of the frequency
(period by period) of the switch mode
supply spreads the wire-conducted
noise throughout the frequency
domain, making the overall noise
level well within what is required in
the EMC directive.
Patent for:
Linearization technology for
loop-powered transmitters
The 3185 and 3186 loop-supplied
isolated transmitters use a DC-current
to AC-current conversion across
the isolation barrier. A small microcontroller continuously measures the
input current and voltage supply and
uses a two dimensional matrix to
select the correct compensation
parameters without error or
non-linearity.
No other competing device can match our performance
in all three areas – without compromise
Temperature devices
Accuracy
0.05% FS
Better than 0.05% accuracy in all
ranges for high signal reliability with
no need for re-calibration.
PR 3000
0.20% FS
Main Competitor
Temperature drift
Designed with a low temperature
drift of 0.01% / °C for high signal
reliability under changing ambient
temperature conditions.
Response time
A response time of less than 30 ms
for accurate measurement of
rapidly changing signals.
160 ms
0.02% / °C
30 ms
0.01% / °C
Signal devices
Accuracy
0.05% FS
Better than 0.05% accuracy in all
ranges for high signal reliability with
no need for re-calibration.
0.1% FS
PR 3000
Main Competitor
Temperature drift
Signal-to-noise ratio
Designed with a low temperature
drift of 0.01% / °C for high signal
reliability under changing ambient
temperature conditions.
60 dB signal-to-noise ratio for a
steady output with high reliability,
even under harsh conditions.
40 dB
60 dB
0.01% / °C
Applicable to
many industries
High performance modules suitable for both process
and factory automation
Our dedication to R&D and understanding
of our customers’ needs have enabled
us to build our expertise across a wide
range of industries, all with varying
needs for process control and signal
conditioning. And the 3000 series is no
different. Our temperature transmitters
and signal devices can be used in many
factory and process automation industries, including: packaging, automotive,
robotics, printing and paper, shipbuilding,
water and wastewater, wood, building
automation, HVAC, energy and more.
Many users value the fast, accurate
measurements, long trouble-free
lifetime and the minimal space requirements due to our narrow housing and
flexible horizontal/vertical mounting
options.
Application examples
Energy
Measuring and isolating steam turbine
bearing temperature sensor signals.
Water & Wastewater
Measuring and isolating liquid level
sensors used in holding ponds.
Chemical & Petrochemical
Measuring and isolating rapidly
changing temperature signals in
bioreactors.
Temperature devices
INPUT
PR
OUTPUT
TC
J&K
Current
Pt100
Ext. CJC
Int. CJC
2-, 3-, 4-wire
Active
Passive
Voltage
FRONT
LED
SUPPLY
3101
HART
ISOLATION
24 VDC
3102
24 VDC
3111
24 VDC / Power rail
2.5 kV
3112
24 VDC / Power rail
2.5 kV
3113
24 VDC / Power rail
2.5 kV
3114*
24 VDC / Power rail
2.5 kV
3331
Loop powered
2.5 kV
3333
Loop powered
3337
Loop powered
2.5 kV
Signal devices
INPUT
OUTPUT
FRONT
LED
SUPPLY
ISOLATION
3103
24 VDC / Power rail
2.5 kV
3104
24 VDC / Power rail
2.5 kV
3105
24 VDC / Power rail
2.5 kV
3108
24 VDC / Power rail
2.5 kV
3109
24 VDC / Power rail
2.5 kV
3114*
24 VDC / Power rail
2.5 kV
3117
24 VDC / Power rail
2.5 kV
3118
24 VDC / Power rail
2.5 kV
3185
Input loop powered
2.5 kV
3186
Output loop powered
2.5 kV
PR
mA
Active
Passive
Voltage
Bipolar
Current
Active
Passive
Voltage
* 3114: Multifunctional converter – see data sheet for additional specifications
Splitter
1 in – 2 out
Energy
Chemical &
Petrochemical
Water &
Wastewater
PR core competences
Low power
consumption
Economical, resource-saving solutions
One of PR’s core competences is our
ability to design and manufacture
high precision technology with
low power consumption. Our high
performance devices not only
deliver a positive impact on the
environment, but also bring you
tangible operational savings.
Because they consume less
power, they also emit less heat.
Our 3000 series is no different and is
designed to deliver exceptional
performance with low power
consumption:
•No air-gap needed, which does not
derate specs – horizontal and
vertical mounting
•Mount 50 devices or 100 channels
in only 30 cm
•Max power consumption < 0.65-1.2 W
meaning less power needed for
cabinet cooling, while increasing
immunity to power dropouts
How to reduce power consumption at your plant?
Selecting the right product can make all the difference in reducing power consumption
at your plant, saving you money.
ompetitor device:
• C
Power supply = 100 watts
Consumption per unit = 0.96 watts
Number of units installed with this power supply: 104 units
• P
R 3112 device:
Power supply = 100 watts
Consumption per unit = 0.70 watts
Number of units installed with this power supply: 142 units
The 3112 consumes 0.26 watts less than competing products, significantly
reducing your power consumption, or allowing you to install 38 more units with
the same supply.
Excellent
EMC performance
Pushing standards in electromagnetic compatibility
PR has always been a pioneer in EMC
and in 1991 we built our own
in-house EMC laboratory. Since then,
we have made significant advancements in designing products for high
EMC performance that do not depend
on using shielded enclosures,
including:
•A sophisticated printed circuit
board layout where wanted and
unwanted signals are being
intelligently routed
•Filters that protect from DC to GHz,
from uV to kV and from uA to A
•A maximum deviation of 0.5% of
the specified range
Beyond our rigorous design process,
we ensure high standards by subjecting our devices to more stringent
testing compared to many competit-
ors. We test by 20 V/m (only 10 V/m
required by the EMC Directive) and
against A criteria (supply and output)
and B criteria (input) mixing the
toughest requirements for both
emissions and immunity.
The result is exceptional EMC
performance even in harsh environments, ensuring stable and accurate
signal conditioning throughout your
process.
Our 3000 series is no different and
delivers exceptional EMC specifications:
•EMC immunity influence < ±0.5% of
the specified range
•NAMUR NE21 burst A criteria < ±1%
of the specified range
•Excellent 50/60 Hz noise suppression
•EN 61326-1 certification
Benefit today from
PERFORMANCE MADE SMARTER
PR electronics is the leading technology
company that specializes in making
industrial process control safer, more
reliable and more efficient. Since 1974
we have been dedicated to perfecting
our core competence of innovating
high-precision technology with low
power consumption. This dedication
continues to set new standards for
products that communicate, monitor
and connect our customers’ process
measurement points to their process
control systems.
Our innovative, patented technologies
are derived from our extensive R&D
­
facilities
andour
ourcustomers’
thorough under
standing of
needs and
processes. We are guided by principles
of simplicity, focus, courage and
excellence, enabling some of the
world’s greatest companies to achieve
PERFORMANCE MADE SMARTER.
1042EN_W01(1430)
Your supplier:
www.prelectronics.com
JSP, s.r.o., Raisova 547, 506 01 Jičín, Czech Republic
Phone: +420 493 760 811, Fax: +420 493 760 820, e-mail: [email protected]
JSP Industrial Controls
www.jsp.cz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement