advertisement
O
AC
US
TIC
AL
PER
FORMANCE PA
RTN
ER
SH
SPECIFICATIONS JF290z
FEATURES
• High output two-way loudspeaker systems with 12-in woofer
and 1.4-in exit/3-in voice coil HF compression driver on
90
°
x 45
°
constant directivity horn
• Beamwidth matching crossover point selection for smooth
power response
• Switchable powering: internal passive crossover or
bi-amplified operation
• Handles and pole mount cup for portable applications
• 3/8”-16 threaded mounting points for permanent
installation
DESCRIPTION
EAW’s JF290z two-way loudspeaker system provides high output, low distortion sound reinforcement for the entire range of pro audio applications.
The newly re-engineered 12-in low frequency cone and 1.4in exit 3-in voice coil high frequency compression driver provides higher output and lower distortion plus enhanced power handling capabilities for better performance in both portable and permanently installed applications. The new constant directivity HF horn – inspired by the new AS Series systems – provides optimized dispersion of HF information without problematic beaming.
EAW’s advanced beamwidth matching crossover selects a crossover point where the HF horn’s beamwidth matches that of the woofer. The result is more even off-axis frequency response (power response) for more complete coverage.
The JF290z offers a switchable powering mode: passive operation using the internal crossover filter network or biamplified operation requiring the use of pre-configured
MX Series processor settings.
APPLICATION
The JF290z was designed to support the widest possible range of pro audio applications and was optimized for use in distributed systems.
The pole mount cup and balance-optimized handles allow for quick and easy load-in of portable uses. Its high output capabilities let it act as a main system for smaller concert or portable A/V events or even provide front or side fill for concert touring applications.
The comprehensive system of integral 3/8”-16 threaded mounting points permit safe, load-rated suspension in permanent installations.
PERFORMANCE
Frequency Response (1 Watt @ 1m, MX200i Processing)
±
3 dB 67 Hz to 17 kHz
-10 dB 55 Hz
Axial Sensitivity (dB SPL, 1 Watt @ 1m)
Full Range 97
LF 96
HF 105
Impedance (Ohms)
Full Range 8
LF 8
HF 16
Power Handling, AES Standard (Watts)
Full Range 500
LF 500
HF 200
Calculated Maximum Output (dB SPL)
Full Range Peak 130.0
LF Peak 130.0
HF Peak 134.0
Full Range Long Term 124.0
LF Long Term 123.0
HF Long Term 128.0
PHYSICAL
Configuration 2-way, full range
Powering Switchable: passive (LF/HF crossover) or bi-amplified
LF Subsystem 1x 12-in, vented
HF Subsystem 1x 1.4-in exit/3-in voice coil compression driver on CD horn
Acoustic Performance Partnership Eastern Acoustic Works
EAW products are continually improved. All specifications are therefore subject to change without notice. • PUB#JF290z-888037 (A)/2 pp/1/29/99 • Printed In USA
JF290z
O
AC
US
TIC
AL
PER
FORMANCE PA
RTN
ER
SH
SPECIFICATIONS JF290z
JF290z CABINET TO BE SYMMETRICAL ABOUT CENTERLINE DESIGNATIONS.
MOUNTING POINT 3/8-16 THREADED HOLE.
3.00 X 1.35 FLY TRACK.
2.06
2.12
13.68
8.59
22.25
18.13
9.50
4.70
8.12
INPUT
FRONT
60 °
10.00
C
6.81
15.25
TOP HAT,
BOTTOM ONLY
BACK
2.06
18.13
2X HANDLES
4.70
(4.02)
510737 (B) exp 8/23/98 shb
TOP/BOTTOM 2X 6.88
SIDES
PHYSICAL
Coverage Angles (h
°
x v
°
) 90 x 45
Cabinet Type (shape) Trapezoidal
Enclosure Materials Baltic birch plywood
Finish Black polyurethane
Connectors 2x Neutrik NL4 Speakon
Suspension Hardware (6) 3/8"-16 threaded mounting/ suspension points (2 each back and sides), (6) 3 position flytrack
(3 each top and bottom), stand mount cup (bottom)
Grille Powder coated perforated steel, foam backed
Controls (switches, knobs) Powering mode switch
Dimensions inches millimeters
Height 22.25
565
Width (Front) 13.68
347
Width (Rear) 4.02
102
Depth (Max) 15.25
387
Trapezoid Angle 30 degrees per side
Weights pounds kilograms
Net Weight 67 30.5
Shipping Weight 74 33.7
SERVICE ITEMS
LF: Complete Cone Driver:
EAW Part No.
804090
HF: Complete Compression Driver/Tweeter:
EAW Part No.
803045
LF: Recone Assembly:
EAW Part No.
460064
HF: Diaphragm Assembly:
EAW Part No.
806049
Filter/Crossover Network: Complete Assembly:
EAW Part No.
225421
A & E SPECIFICATIONS
The two-way full range loudspeaker systems shall incorporate a 12-in LF transducers and a 1.4-in exit/3-in voice coil compression driver HF transducer.
The LF driver shall be mounted in a vented enclosure tuned for optimum low frequency response. The HF driver shall be loaded on a constant directivity horn with a nominal coverage pattern of 90
°
(h) x 45
°
(v).
A switch shall be provided allowing the user to select between bi-amplified or full range passive powering modes. In full range passive mode, an internal passive filter network shall provide fourth order acoustical crossover and system equalization between the low and high frequency sections.
System frequency response shall vary no more than
±
3 dB from 67 Hz to 17 kHz measured on axis. In full range mode, the system shall produce a Sound Pressure Level (SPL) of 97 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 129.0 dB SPL on axis at 1 meter. In full range mode, the system shall handle 500 Watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 Ohms.
In biamplified mode, the low frequency section shall produce a Sound Pressure Level (SPL) of 96 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 129.0 dB SPL on axis at 1 meter, and the high frequency section shall produce a Sound Pressure Level (SPL) of 105 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 134.0 dB SPL on axis at 1 meter. In biamplified mode, the low frequency section shall handle 500 Watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 Ohms and the high frequency section shall handle 200 Watts of amplifier power and shall have a nominal impedance of 16 Ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of 1/2-in thickness void-free cross-grainlaminated Baltic birch plywood and shall employ extensive internal bracing. It shall be finished in black catalyzed polyurethane. Input connectors shall be dual Neutrik NL4. A total of 6x 3/8"-16 threaded mounting/suspension points (2 each sides and back) shall be provided as well as 6x 3-position flytracks (3 each top and bottom). A stand mount cup shall be provided on the bottom of the enclosure. The front of the loudspeaker shall be covered with a vinyl coated perforated steel grille.
The 2-way full range loudspeaker shall be the EAW model
JF290z.
Acoustic Performance Partnership Eastern Acoustic Works JF290z
One Main Street, Whitinsville MA, 01588 USA • Phone 508/234-6158 • Toll Free 800/992-5013 • Fax 508/234-8251 • Web http://www.eaw.com • email [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project