advertisement
HP
A-MSR20_A-MSR30_A-MSR50_A-MSR900-C
MW520-R2312P15-SI
© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
The information in this document is subject to change without notice.
HP
A-MSR20_A-MSR30_A-MSR50_A-MSR900-C
MW520-R2312P15-SI Release Notes
Keywords: Version Information, Unresolved Problems and Avoidance Measure
Abstract: This release notes describes the R2312P15 release with respect to hardware and software compatibility, released features and functions, software upgrading, and documentation.
Acronyms:
Acronym
LAN
PIM
LPM
QoS
UTP
SFP
DHCP
OSPF
RIP
ARP
AAA
RSTP
MAC
IGMP
VLAN
STP
RMON
GMRP
ACL
GBIC
Full spelling
Local Area Network
Media Access Control
Internet Group Management Protocol
Virtual Local Area Network
Spanning Tree Protocol
Remote Monitor(SNMP)
GARP Multicast Registration Protocol
Access Control List
Dynamic Host Configuration Protocol
Open Shortest Path First
Routing Information Protocol
Address Resolution Protocol
Authentication Authorization Accounting
Rapid Spanning Tree Protocol
Protocol Independent Multicast
Longest Prefix Match
Quality of Service
Unshielded Twisted Paired
Small Form-Factor Pluggable
Gigabit Interface Converter
1
Contents
i
Technical support ················································································································· 38
ii
List of Tables
iii
This document describes the features, restrictions and guidelines, open problems, and workarounds for version R2312P15. Before you use this version in a live network, back up the configuration and test the version to avoid software upgrade affecting your live network.
Use this document in conjunction with HP
A-MSR20_A-MSR30_A-MSR50_A-MSR900-CMW520-R2312P15-SI Release Notes (Software
Feature Changes) and the documents listed in "Related documentation"
Important information
Passwords created in configuration files by software version prior to F2208 were held in a different format. To avoid any problems downgrading software, please backup the configuration file before upgrading from an earlier version of code. More details may
be found in the Open problems and workarounds section below.
Version information
Version number
A-MSR 20-20_A-MSR 20-21_A-MSR 20-40_A-MSR30-16_A-MSR 30-20_A-MSR 30-40_A-MSR
30-60_A-MSR 50-40_A-MSR 50-60_A-MSR 50-40 MPU-G2_A-MSR 50-60 MPU-G2_A-MSR30-1X:
Comware software, Version 5.20, Rlease 2312P15, Standard
A-MSR9XX_A-MSR20-1X:
Comware software, Version 5.20, Rlease 2312P15
Note: You can see the version number with the command display version in any view.
Please see Note①.
Version history
Table 1 Version history
Version number Last version
Release
Date
Release type
Release version
CMW520-R2312P1
5
CMW520-R23
12
2012-12-27
Remarks
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
New Features:
1. Jitter buffer
2. Different authentication keys for
TACACS servers
3. Destination MAC check on VE
4
Version number Last version
Release
Date
Release type
CMW520-R2312
CMW520-R23
11
2012-10-25
CMW520-E2310
CMW520-R22
09P21
2012-09-20
Release version
CMW520-R2311
CMW520-E23
10
2012-10-16
Release version
Release version
Remarks interfaces
4. Support for FIPS and CC certification
5. Disabling password recovery capability
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
New Features:
1. CAR support percent configuration
2. LYNC gateway authentication test
3. IMC SMS-based configuration deployment
4. NAT traversal for main-mode PSK
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
New Features:
1. Advanced ASPF
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
New Features:
1.DVPN support for VPN instances
2.Configuring the FXS interfaces to use DTMF-based CID
3.IPsec support for IPv6
4.Configuring call forwarding authority control
5.Configuring analog E&M line failure tone
6.Supporting the Sierra 313U, 320U, and 312U 3G modems
7.Bulk configuring interfaces
8.Configuring enhanced SIP trunk features
9.Enabling the number substitution function
10.Sending both the access number and
11.called number to the softswitch
12.The QoS policy applied to a
5
Version number Last version
Release
Date
Release type
CMW520-R22
09P15
CMW520-R2209P2
1
CMW520-R22
09P19
2012-06-14
CMW520-R2209P1
9
CMW520-R22
09P01
2012-06-14
Release version
Release version
CMW520-R2209P1
5
CMW520-R22
09P13
2012-05-17
Release version
CMW520-R2209P1
3
CMW520-R22
09P01
2012-04-23
Release version
6
Remarks main interface taking effect on subinterfaces
13.Configuring call transfer authority control
14.Supporting the maddr parameter
15.Configuring dynamic BGP peers
16.MPLS VRF MIB support
17.GET VPN
18.Supporting unicast/broadcast-to-multicast and multicast-to-unicast/broadcast conversions
19.Adding MIB files for 3G modems
20. Assign the private network in next-hop for policy-based routing
Modified Features:
1.IP source guard
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Support map a nonstandard port to an application layer protocol for NAT ALG
2. The console interface of
A-MSR900/MSR900 and
A-MSR920/MSR920 support the
function of the auxiliary interface, and Only the A-MSR900/MSR900 and A-MSR920/MSR920 which's
PCB versions are 3.0 or higher can support this function.
Fixes bugs
Only support A-MSR9XX series and
MSR9XX series
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Support Sierra 313U modem
2. Support to auto-configure the router by USB disk
3. Extend A-MSR50 OSPF maximum area amount to 200
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
Version number Last version
Release
Date
Release type
CMW520-R2209P0
1
CMW520-R22
09
2012-03-28
CMW520-R22
07P45
CMW520-R2209
CMW520-F22
08
2012-02-14
CMW520-R2207P4
5
CMW520-R22
07P38
2011-12-28
Release version
Release version
Release version
Remarks
1. Support to set the OEM flag of
A-MSR
2. Support to disable the USB port using the command
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Support to set the OEM flag of
A-MSR router from HP to 3COM using the command (can't be supported at MSR3010/3011E/
3011F and MPU-G2)
2. Support to filter packets based on MAC Addresses, and any attempt to break this rule must to be logged and to send a SNMP trap
3. Support to assign IPv6 address of
/127 prefix on link interfaces
4. Judge whether the software version can support this hardware before updating the software version
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. CWMP support for configuring multiple ACS servers.
2. Support multicast UDPH function
3. Support to using the sub-address of the interface sending and receiving RIP routes
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Using the command of
“impedance south-africa” to set the FXO interface’s ringing impedance
2. Support HUAWEI EC1261 3G modem
3. If The NAT and IPSEC functions were enabled at the same interface, the command of “ipsec no-nat-process enable” can control that packets don’t do NAT transition before IPSEC
7
Version number Last version
Release
Date
Release type
CMW520-F2208
CMW520-R22
07P38
2011-12-08
Release version
Release version
CMW520-R2207P3
8
CMW520-R22
07P34
2011-11-18
CMW520-R2207P3
4
CMW520-R22
07P23
2011-10-19
Release version
CMW520-R2207P3
3
CMW520-R22
07P02
2011-10-08
Release version
Release version
CMW520-R2207P2
3
CMW520-R22
07P14
2011-09-15
CMW520-R2207P1
4
CMW520-R22
07P02
2011-08-17
Release version
Remarks
4. Support of CWMP over AES-256
SSL tunnel
5. Support of CWMP (TR-069) over
SSL for BIMS and the router
Fixes bugs
Code Optimize, Support
A-MSR20_30_50_900 series and
MSR20_30_50_900 series
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. The MIM-G.SHDSL and
FIC-G.SHDSL card supported the
Whip function
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Support Huawei E261 3G modem and ZTE MF190 3G modem
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New Features:
1. Delay to notify the status change of interface
2. Support to encrypt HWTACAS
Key
3. The Statistic information of the
MFR main interface included the input and output packets from sub-interface.
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New Features:
1. The number of NAT address pool was extended to 64 from 32.
2. Support Sierra 250U and 308U 3G modem at the A-MSR20/A-MSR30/
A-MSR9XX router.
3. Support HUAWEI E173 WCDMA modem
4. Support to Configure TPID on a
8
Version number Last version
Release
Date
Release type
CMW520-R2207P0
2
CMW520-R22
07
2011-06-23
Release version
CMW520-R2207
CMW520-R21
05P38
2011-05-19
Release version
Remarks
Layer 3 Ethernet or VE interface, and to implement VLAN termination.
5. Support to transit the extendedVideoCapability field of
H245 packets in the NAT ALG
6. Support the DVPN instance.
7. The QoS policy of main interface can apply to sub-interface.
8. Support the Refer-by field of the
SIP packets.
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Support the statistics per classifier of nested QoS
Fixes bugs
Support A-MSR20_30_50_900 series and MSR20_30_50_900 series
New features:
1. Call forwarding authority control
2. Support DAR MIB
3. Authorization again for AAA
4. The feature supports the VPN could visit the other VPN by NAT
5. Support OSPF and NAT in bridge-template interface
6. WCDMA 3G Modem
7. CDMA2000 3G Modem
8. TD-SCDMA 3G Modem
9. SIP TRUNKING
10. SRTP
11. L2VPN connected to L3VPN
12. NAT DMZ host and related features
13. SIP support for non early media
negotiation
14. IPsec RRI
15. Allows you to configure NAT address groups, NAT server, and attack protection through TR069.
16. Support of routing protocols for
9
Version number Last version
Release
Date
Release type
Remarks
6VPE
17. BIDIR-PIM
18. OSPFv3 support for MCE
19. Voice support for TR104
20. BGP, OSPFv3 and ISISv6 support for IPv6 VPN BFD
21. Allows you to set a BGP update interval of 0.
22. Allows you to use domain names to specify SNMP trap and log hosts.
23. TR069 supports the following memory and CPU utilization nodes:
24. ACL configuration information display filtering
25. A routing policy name can contain up to 64 characters.
26. Allows you to use names as
BGP community attributes
27. Permanent attribute for static routes
28. Continue feature for routing policy
29. E1POS and AM ports can send calling numbers.
30. POS terminal access can use the source address in the TPDU header to map POS packets to specific POS applications.
31. POS terminal access allows you to specify TCP source port numbers for POS applications.
32. Bloomberg MSR Source NAT
33. NAT support for discontinuous address pools
34. ISDN support for sending the progress-indicator unit
35. An ACL name can contain up to 63 characters.
36. POS MIB and E1 POS MIB
37. SIP support for SRV and NAPTR
38. TR098
10
Version number Last version
Release
Date
Release type
Release version
CMW520-R2105P3
8
CMW520-R21
05P36
2011-05-17
CMW520-R2105P3
6
CMW520-R21
05P35
2011-04-19
Release version
Release version
CMW520-R2105P3
5
CMW520-R21
05P31
2011-03-30
CMW520-R2105P3
1
CMW520-R21
05P26
2011-03-08
Release version
CMW520-R2105P2
6
CMW520-R21
05P25
CMW520-R2105P2
5
CMW520-R21
05P22
2011-02-16
Release version
2011-01-28
Release version
Release version
CMW520-R2105P2
2
CMW520-R21
05P12
2011-01-19
CMW520-R2105P1
2
CMW520-R21
05P06
2010-12-10
Release version
11
Remarks
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support FRF.12 fragment function based on the interface
2. FIPS features appended
Fixes bugs
Support MSR20_30_50_900 series
Fixes bugs
Only support MSR 30_50_50
MPU-G2
Series
New features:
1. Support the statistics per classifier of nested QoS
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support the packets and the rate Statistic at the vlan-interface
2. Set the number of interframe filling tag using the command
3. Support to assign the IP address of next server offering service for the DHCP client
Fixes bugs
Support MSR20_30_50_900 series
Fixes bugs
Only support MSR30-1X series
New features:
1. Support FIPS.
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support to set virtual bandwidth using the command of
“bandwidth” at the interface.
2. At best every VRF can support
10000 routes at the MSR50 router.
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support HUAWEI E367 models of
Version number Last version
Release
Date
CMW520-R2105P0
9
CMW520-R21
04P02
2010-09-19
Release version
Release version
CMW520-R2105P0
6
CMW520-R21
05P02
2010-11-25
CMW520-R2105P0
2
CMW520-R21
05
2010-10-15
CMW520-R2105
CMW520-R21
04P02
2010-09-13
CMW520-R2104P0
2
First release
Release type
Release version
Release version
2010-08-17
Release version
Remarks
WCDMA 3G Modems.
2. MSR50 MPU-G2 can support
10000 rules each ACL.
3. Support remarking the protocol packets from the router itself.
Fixes bugs
Only support MSR30-1X series
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support HUAWEI E1553 models of
WCDMA 3G Modems.
2. IPv6 capabilities in VPNs
3. Support LLDP in LAN
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Excluding the ACL information when displaying current configuration
2. It can be enlarged to 64 characters for the route-policy name, a case-sensitive string of 1 to 63 characters.
3. It can put a name to describe the BGP community lists, a string of
1 to 31 characters (not all are numbers).
4. Permanent Static Route
Fixes bugs
Support MSR20_30_50_900 series
New features:
1. Support HUAWEI E1820 models of
WCDMA 3G Modem
2. BIDIR-PIM
Fixes bugs
Support MSR20_30_50_900 series
New features:
Fixes bugs
Hardware and software compatibility matrix
HP A-MSR product family matrix:
12
Before HP A-MSR family, there were another 2 product families, i.e. 3Com MSR and H3C
MSR, shipped to market. All of these three product families have same hardware and software specification except brand. The product matrix is as following. In brief, the HP
A-MSR SKU will be the representation to all of them in subsequent document.
Table 2 Product matrix
HP A-MSR series
A-MSR20-1X series: A-MSR
20-10_ A-MSR 20-11_ A-MSR
20-12_ A-MSR 20-13 (No A-MSR
20-15)
A-MSR 20-20_A-MSR
20-21_A-MSR 20-40
None
A-MSR30-1X series:
A-MSR30-10_A-MSR30-11E_A-M
SR30-11F
A-MSR 30-16
A-MSR30-20_A-MSR
30-40_A-MSR 30-60
A-MSR 50-40_A-MSR 50-60_
A-MSR 50-40 MPU-G2_A-MSR
50-60 MPU-G2
A-MSR9XX series: A-MSR
900_A-MSR920
H3C MSR series 3Com MSR series
MSR20-1X series: MSR 20-10_MSR
20-11_MSR 20-12_MSR
20-13_MSR 20-15
MSR20-1X series: MSR
20-10_MSR 20-11_MSR
20-12_MSR 20-13_MSR 20-15
MSR 20-20_MSR 20-21_MSR
20-40
MSR30-11
Only MSR30-10
MSR 20-20_MSR 20-21_MSR
20-40
None
None
MSR 30-16
MSR30-20_MSR 30-40_MSR 30-60
MSR 30-16
MSR30-20_MSR 30-40_MSR
30-60
MSR 50-40_MSR 50-60_MSR
50-40 MPU-G2_MSR 50-60
MPU-G2
MSR 50-40_MSR 50-60
MSR9XX series: MSR 900_MSR920 None
Table 3 Hardware and software compatibility matrix
Item
Product family
Specifications
A-MSR20_30_50_900 series routers
Hardware platform
Boot
ROM version
A-MSR20-1X series: A-MSR 20-10_ A-MSR 20-11_ A-MSR 20-12_ A-MSR 20-13/MSR 20-15
A-MSR 20-20_A-MSR 20-21_A-MSR 20-40
MSR30-11
A-MSR30-1X series: A-MSR30-10_A-MSR30-11E_A-MSR30-11F
A-MSR 30-16
A-MSR30-20_A-MSR 30-40_A-MSR 30-60
A-MSR 50-40_A-MSR 50-60_ A-MSR 50-40 MPU-G2_A-MSR 50-60 MPU-G2
A-MSR9XX series: A-MSR 900_A-MSR920
A-MSR20-1X series: 300 or higher
A-MSR 20-20_A-MSR 20-21_A-MSR 20-40: 400 or higher
A-MSR30-1X series: 300 or higher
A-MSR 30-16: 300 or higher
A-MSR30-20_A-MSR 30-40_A-MSR 30-60: 400 or higher
A-MSR 50-40_A-MSR 50-60: 400 or higher
13
Item
Host software iMC version
Specifications
A-MSR 50-40 MPU-G2_A-MSR 50-60 MPU-G2: 200 or higher
A-MSR9XX series: 200 or higher
(Note: Perform the command display version command in any view to view the version information. Please see Note②)
Hardware
A-MSR 20-20_A-MSR
20-21_A-MSR 20-40
A-MSR20-1X series
A-MSR30-1X series
A-MSR 30-16
A-MSR 30-20_A-MSR
30-40_A-MSR 30-60
A-MSR 50-40_A-MSR
50-60
A-MSR 50-40 MPU-G2_
A-MSR 50-60 MPU-G2 software
A_MSR20-CMW520-R231
2P15-SI.BIN
A_MSR201X-CMW520-R2
312P15.BIN
A_MSR301X-CMW520-R2
312P15-SI.BIN
A_MSR3016-CMW520-R2
312P15-SI.BIN
A_MSR30-CMW520-R231
2P15-SI.BIN
A_MSR50-CMW520-R231
2P15-SI.BIN
A_MSR50-CMW520-R231
2P15-EPUSI.BIN
A-MSR 900_A-MSR920
A_MSR9XX-CMW520-R23
12P15.BIN iMC PLAT 5.1 SP1 (E0202P05) iMC UAM 5.1 SP1 (E0301P03) iMC EAD 5.1 SP1 (E0301P03) iMC MVM 5.1 SP1 (E0201P01) iMC VSM 5.1 (E0201) iMC QoSM 5.1 (E0201) iMC TAM 5.1 (E0301)
MD5 Check Sum b6faf0b218b47b6ce0e3a11dd58 e9577 eb08728c4028ce0b74f30016ea6
21fd7 f9498c8f2f76dd2c2f7599350bb74
69c
657f0062e352acde78672c82fc3c
675e
64509980dc9fa1090b898150f7d2 c539
5bb1c8e84eb5fd745f8375ae1238
3357
918ca27d88b975ecb767184b8e0
2ac15
4eb822559c78cd8614d453b6d64
16691 iNode PC 5.1 (E0304) iNode version
Cards
Version
Cards Name
SIC-AP
SIC-ADSL-I/SIC-ADSL-P
MIM-6FCM/FIC-6FCM
FIC-24FXS
DFIC-24FXO24FXS
Software Version
R3200 or higher
230 or higher
230 or higher
200 or higher
200 or higher
SIC-2BSV/MIM-4BSV/FIC-4BSV None
VCPM: RTV1VCPM None
CPLD or FPGA version
200 or higher
100 or higher
100 or higher
100 or higher
100 or higher
CPLD: 200 or higher
CPLD: 100 or higher
FPGA: 400 or higher
Sample: To display the host software and Boot ROM version of the A-MSR routers, perform the following:
14
<Sysname> display version
HP Comware Platform Software
Comware Software, Version 5.20, Release 2312P15, Standard ------- Note①
Copyright (c) 2010-2012 Hewlett-Packard Development Company, L.P.
HP A-MSR30-60 uptime is 0 week, 0 day, 0 hour, 1 minute
Last reboot 2011/06/02 09:58:02
System returned to ROM By <Reboot> Command.
CPU type: FREESCALE MPC8349 533MHz
512M bytes DDR SDRAM Memory
4M bytes Flash Memory
Pcb Version: 4.0
Logic Version: 3.0
Basic BootROM Version: 4.00
Extended BootROM Version: 4.00 ------- Note②
[SLOT 0]CON (Hardware)4.0 (Driver)1.0, (Cpld)3.0
[SLOT 0]AUX (Hardware)4.0 (Driver)1.0, (Cpld)3.0
[SLOT 0]GE0/0 (Hardware)4.0 (Driver)1.0, (Cpld)3.0
[SLOT 0]GE0/1 (Hardware)4.0 (Driver)1.0, (Cpld)3.0
[SLOT 0]CELLULAR0/0 (Hardware)4.0 (Driver)1.0, (Cpld)3.0
Upgrading restrictions and guidelines
Hardware feature updates
CMW520-R2312P15
None
CMW520-E2310
New features: TOSHIBA flash is supported on MSR 30-11E/MSR 30-11F/MSR 30-10/MSR
900/MSR 920.
Deleted features: None
Software feature and command updates
For more information about the software feature and command update history, see HP
A-MSR20_A-MSR30_A-MSR50_A-MSR900-CMW520-R2312P15-SI Release Notes (Software
Feature Changes).
15
MIB updates
Table 4 MIB updates
Item MIB file
CMW520-R2312P15
Module Description
None
Modified hh3c-3gmodem.mi
b hh3c-3gmodem.mi
b
HH3C-3GMODE
M-MIB
HH3C-3GMODE
M-MIB
Added hh3cSmsOperationTable, hh3cWirelessCardOnlineTable, hh3cLteInfoTable.
And add hh3cWirelessCardModemMode, hh3cWirelessCardCurNetConn in hh3cWirelessCardTable, add hh3c3GGsmMcc, hh3c3GGsmMnc in hh3c3GgsmInfoTable, add hh3cSmsRxNotifSwitch, hh3cSmsSrcNumberBind, hh3cSmsTimeBind, hh3cSmsEncodeBind in Scalar objects.
Add hh3cSmsTxNotification, hh3cSmsRxNotification in traps.
Modified PDS of hh3cWirelessCardTable, hh3cUIMInfoTable, hh3c3GCdma1xRttTable, hh3c3GcdmaEvDoTable, hh3c3GgsmInfoTable
CMW520-E2310
New rfc3815-mpls-ldp-st d.mib hh3c-entity-ext.mib
MPLS-LDP-STD-MI
B
HH3C-ENTITY-EXT-
MIB
Add mplsFecIndex, mplsFecType, mplsFecAddrPrefixLength, mplsFecAddrType, mplsFecAddr, mplsFecStorageType, mplsFecRowStatus
Add hh3cEntityExtCpuUsageRecoverThreshol d in hh3cEntityExtStateTable rfc2674-qbridge.mi
b
Q-BRIDGE-MIB Add dot1qVlanCurrentTable rfc2096-ip-forward.
mib hh3c-config-man.m
ib hh3c-config-man.m
ib hh3c-flash-man.mib
IP-FORWARD-MIB
HH3C-CONFIG-
MAN-MIB
HH3C-CONFIG-
MAN-MIB
HH3C-FLASH-MA
N-MIB
Add inetCidrRouteNumber, inetCidrRouteDiscards and inetCidrRouteTable
Add hh3cCfgLogCmdSrcAddrType, hh3cCfgLogCmdSrcAddrRev, hh3cCfgLogServerAddrType, hh3cCfgLogServerAddrRev, hh3cCfgLogServerAddrVPNName in hh3cCfgLogTable
Add hh3cCfgOperateSrvAddrType, hh3cCfgOperateSrvAddrRev, hh3cCfgOperateSrvVPNName in hh3cCfgOperateTable
Add hh3cFlhOperSrvAddrType, hh3cFlhOperSrvAddrRev and
16
Item
Modified
MIB file
Hh3c-posa.mib hh3c-3gmodem.mi
b lldp-ext-dot1.mib hh3c-sys-man.mib rfc1213.mib rfc3813-mpls-lsr-std.
mib
Module
HH3C-
POSA-
MIB
HH3C-3GMODE
M-MIB
LLDP-EXT-DOT1-
MIB
HH3C-SYS-MAN-
MIB
RFC1213-MIB hh3c-splat-vlan.mib
HH3C-LswVLAN-
MIB
MPLS-LSR-STD-MI
B
Description hh3cFlhOperSrvVPNName hh3cFlhOpTable
Add hh3cPosaAppName, hh3cPosaCallerIDTransEnable, hh3cPosaTpduChangeStrateg y, hh3cPosaBackupAppID and hh3cPosaQuietTimeOut in hh3cPosaAppTable
Add hh3cWirelessCardInterfaceIndex, hh3cWirelessCardModemStatus, hh3cWirelessCardCurServiceStatus, hh3cWirelessCardCurRoamingStatus inhh3cWirelessCardTable;
Add hh3cDeviceOUI,hh3cAccessMedia,hh3c
3GCurrentService,hh3c3GCurrentRssiBin d,hh3c3GImsiBind in Scalar objects;
And add hh3c3GCdma1xRttTable,hh3c3GcdmaE vDoTable,hh3c3GgsmInfoTable
Modified the Default value of lldpXdot1ConfigVlanNameTxEnable,lldp
Xdot1ConfigProtoVlanTxEnableto FALSE
Modified the PDS of scalar objects
Modified the description of sysDescr and sysObjectID
Modified the description of hh3cdot1qVlanName,delete the Default value.
Modified the description of mplsInSegmentStorageType, mplsOutSegmentStorageType, mplsXCStorageType, mplsLabelStackStorageType, mplsTunnelNotificationMaxRate, mplsTunnelNotificationEnable, mplsTunnelSessionAttributes, mplsTunnelResourcePointer, mplsTunnelPrimaryInstance, mplsTunnelInstancePriority, mplsTunnelPathInUse, mplsTunnelTotalUpTime, mplsTunnelInstanceUpTime, mplsTunnelPrimaryUpTime, mplsTunnelPathChanges, mplsTunnelLastPathChange, mplsTunnelCreationTime, mplsTunnelStateTransitions, mplsTunnelRowStatus, mplsTunnelStorageType, mplsTunnelHopAsNumber, mplsTunnelHopAddrUnnum,
17
Item MIB file rfc1213.mib hh3c-acl.mib hh3c-3gmodem.mi
b rfc3815-mpls-ldp-st d.mib rfc3814-mpls-ftn-std.
mib
MPLS-FTN-STD-MI
B rfc2787-vrrp.mib
Module
RFC1213-MIB
HH3C-ACL-MIB hh3c-flash-man.mib
HH3C-FLASH-MA
N-MIB
HH3C-3GMODE
M-MIB
MPLS-LDP-STD-MI
B
VRRP-MIB
Description mplsTunnelHopLspId, mplsTunnelHopEntryPathComp, mplsTunnelHopRowStatus, mplsTunnelHopStorageType, mplsTunnelResourceRowStatus, mplsTunnelResourceStorageType, mplsTunnelARHopAddrUnnum, mplsTunnelCHopAsNumber, mplsTunnelCHopAddrUnnum, mplsTunnelCRLDPResRowStatus and mplsTunnelCRLDPResStorageType
Modified the description of ifOperStatus, delete link status
Modified the description of hh3cAclIPAclBasicVpnInstanceName and hh3cAclIPAclAdvancedVpnInstanceNa me
Modified the description of hh3cFlhOperIndex, hh3cFlhOperSourceFile, hh3cFlhOperDestinationFile in hh3cFlhOpTable
Modified the description of hh3cWirelessCardIndex in hh3cWirelessCardTable
Modified the description of mplsLdpEntityStatsSessionRejectedMaxP duErrors, mplsLdpSessionStatsUnknownMesTypeErr ors and mplsLdpSessionStatsUnknownTlvErrors
Modified the description of mplsFTNSourceAddrMin, mplsFTNSourceAddrMax, mplsFTNDscp and mplsLabelStackTable
Modified the description of vrrpNodeVersion and vrrpOperAdvertisementInterval
CMW520-R2209P01
New None None
Modified hh3c-config-man.m
ib
HH3C-CONFIG-
MAN-MIB
None
Modified the description of hh3cCfgLogTerminalUser in hh3cCfgLogTable
CMW520-R2209
New None None
Modified rfc1213.mib RFC1213-MIB
None
Modified all the descriptions of ipv6InterfaceTable, ipSystemStatsTable,
18
Item MIB file Module Description ipIfStatsTable, ipAddressPrefixTable, ipAddressTable, ipNetToPhysicalTable, ipv6ScopeZoneIndexTable, ipDefaultRouterTable, ipv6RouterAdvertTable, icmpStatsTable and icmpMsgStatsTable to Not supported
CMW520-R2207P02
New rfc2515-atm.mib rfc2515-atm.mib rfc1213.mib
ATM-MIB
ATM-MIB
RFC1213-MIB
HH3C-DAR-MIB
None
Add ATMIMA to the table of atmInterfaceMaxActiveVciBits
Add GBIS and ATMIMA to the table of atmInterfaceMaxVccs
Modified description of ifSpeed from an estimate of the interface's current bandwidth in bits per second to configured by the bandwidth command, and it's different in various types of interfaces by default.
Modified the oid of hh3cDarStatisticsTable
None hh3c-dar.mib
Modified None
CMW520-R2207 hh3c-nqa.mib
New
Modified hh3c-nqa.mib
Hh3c-e1t1vi.mib hh3c-e1.mib hh3c-splat-mstp.mi
b hh3c-dhcps.mib rfc1657-bgp4.mib
Hh3c-posa.mib
HH3C-NQA-MIB
Add hh3cNqaStatisticsReactionTable and h3cNqaReactionTable
HH3C-NQA-MIB
Add such TRAPs in HH3C-NQA-MIB: hh3cNqaProbeTimeOverThreshold, hh3cNqaJitterRTTOverThreshold, hh3cNqaProbeFailure, hh3cNqaJitterPacketLoss, hh3cNqaJitterSDOverThreshold, hh3cNqaJitterDSOverThreshold, hh3cNqaICPIFOverThreshold and hh3cNqaMOSOverThreshold
HH3C-E1T1VI-MIB Add hh3cE1T1VITrapTimeSlotEnable
HH3C-E1-MIB
Add hh3ce1FcmChannelIndex and hh3ce1TimeSlotSetTable
HH3C-LswMSTP-
MIB
HH3C-DHCPS-MI
B
Modified the description of hh3cdot1sMstAdminFormatSelector.
Changed the value range from [0..255] to 0
Modified the description of hh3cDHCPSGlobalPoolLeaseUnlimited.
Added the value can’t be set to 0
BGP4-MIB
HH3C-POSA-MIB
Modified the PDS of bgpeerAdminStatus, bgpPeerHoldTimeConfigured, bgpPeerKeepAliveConfigured, bgpPeerMinASOriginationInterval and bgpPeerMinRouteAdvertisementInterval
Modified the PDS of hh3cPosaTerminalTable and
19
Item MIB file Module Description hh3cPosaAppTable
Operation changes
None.
Restrictions and cautions
1. This product complies with the European Radio & Telecommunication Terminal
Equipment Directive 1999/5/EC. Based on this evaluation, a minimum distance of 25 cm between the 3G antennas and between the 3G antenna and the WiFi antenna is required to maintain compliance and receiver reliability.
2. It is recommended that the A-MSR900/MSR900 and A-MSR920/MSR920 which's PCB versions are 3.0 or higher use the software R2209P19 or later versions. If the old software versions are used, the console interface of the A-MSR900/MSR900 and A-MSR920/MSR920 will be flow controlled, and it is necessary to forbid detecting the RTS/CTS signal at the terminal software in order to manage the console interface normally.
Open problems and workarounds
RTD58409
Symptom:
In this version of code, the password encryption within configuration files has been enhanced and cannot be interpreted by earlier revisions of the agent code. This means that if a unit is downgraded to earlier code, it may no longer be possible to login and manage the device.
Workarounds:
Before upgrading to the new code, it is necessary to ensure password control is disabled.
Execute the “undo password-control enable” and then save this configuration file as a backup in case you need to downgrade the software again. If it is later necessary to downgrade to earlier software, force the router to use this backup configuration file by executing a ”startup saved-configuration (filename)” command before rebooting to the old code. Then, after the code has been downgraded, the device can be logged in from the console or by Telnet, but not SSH. The SSH authentication details will need to be reset.
If no backup configuration has been saved but it is still possible to access the device management via some method while running the old code (e.g. Console, Telnet or SSH), then you can redefine all the device management passwords as required.
20
If after a downgrade it is impossible to login to the device via any method, then there are two ways to recover the router:
From the BOOT menu, set the new code to run again and reboot the device.
Disable Telnet authentication: a.
User-interface vty 0 4 b.
Authentication mode none c.
Then save the configuration and downgrade the code again, login via Telnet and reset all the passwords as required.
From the BOOT menu. On boot-up, use Ctrl+B to enter the Boot menu and then force the unit to use the factory default configuration (bypassing the user configuration). The unit will then need to be fully reconfigured.
List of resolved problems
Resolved problems in CMW520-R2312P15
RTD064289
Symptom: When an AE3 card of a router connects to non-H3C device, the router cannot communicate with the non-H3C device because the peer port cannot come up.
Condition: This symptom occurs if the non-H3C device checks the payload type field of E3 frames and finds that the field does not match its implementation.
RTD063995
Symptom: When access the hh3cUserPassword node of hh3cUserInfoTable by SNMP, the device return the user's password.
Condition: Access the hh3cUserPassword node of hh3cUserInfoTable by SNMP.
HSD81844
Symptom: Because of the weak cryptographic algorithm there is a risk that the stored passwords possibly be cracked.
Condition: Config password in ciphertext.
HSD82338
Symptom: Memory leak occurs on some specific LDAP query in SSL VPN feature.
Condition: Specific LDAP query in SSL VPN.
HSD76273
Symptom: Buffer overflow occurs on some specific illegal IKE packet.
Condition: Illegal IKE packet attack.
21
Resolved problems in CMW520-R2312
RTD063095
Symptom: When communication with the remote SIP server recovers, the router that acts as the local SIP server still responds to SIP register requests.
Condition: This symptom occurs when the following conditions exist:
The router operates in alive mode.
Communication with the remote SIP server fails and after a certain time, it recovers.
RTD063683
Symptom: The MSR router cannot be accessed by some wireless devices.
Condition: This symptom occurs if the IE extended attributes of the wireless devices fail to pass check on the MSR router.
RTD063679
Symptom: A port that is configured with nat outbound and is not configured with nat server
still performs NAT server translation for received packets.
Condition: This symptom might occur if the port is one of the two public ports of the router, and the other public port is configured with nat server.
RTD064096
Symptom: The MSR router that acts as the LNS cannot be accessed by other devices.
Condition: This symptom occurs because FrameCap AVP in SCCRP sent by the MSR is
TRUE, resulting in PPP negotiation failures.
RTD063561
Symptom: Packet forwarding between secondary addresses configured on a VLAN interface has low efficiency.
Condition: This symptom occurs during packet forwarding between secondary addresses configured on a VLAN interface.
Resolved problems in CMW520-R2311
RTD063829
Symptom: If the router starts up without loading a configuration file, multiple voice-related TCP ports are enabled.
Condition: This symptom occurs if the router starts up without loading a configuration file.
22
Resolved problems in CMW520-E2310
RTD063149
Description: The display rta all command cannot display complete RTA template information.
Condition: This symptom might occur when more than 24 RTA templates have been configured.
RTD063140
Description: Changing user privileges in the Web interface fails.
Condition: This symptom occurs when you change a user privilege in the Web interface.
RTD063433
Description: An MSR 30-11F router that performs 802.1X authentication fails to execute permit rules in an assigned ACL.
Condition: This symptom might occur if the assigned ACL comprises both permit and deny rules.
RTD063426
Description: An X.25 SVC fails to be established.
Condition: This symptom occurs if the call request received from the X.25 peer has a facility ID of 00.
RTD063577
Description: A client fails to pass 802.1X authentication on the router.
Condition: This symptom occurs if the client is enabled with IP check function.
Resolved problems in CMW520-R2209P21
RTD062073
Symptom: Because the external 3G modem negotiates slowly, if the PPPoE client waits for PPP negotiation more than 10s, the PPPoE dialer will fail.
Condition: MSR device as PPPoE client, and connected with external 3G modem.
RTD061928
Symptom: The power level measured is greater than the maximum power level allowed by the standard 12.5dBm.
Condition: The test house carries out the Annex L testing for the SIC-ADSL card.
23
RTD061985
Symptom: The UMTS light on the SIC-3G-GSM or SIC-HSPA card is bright yellow all along.
Condition: The SIM card can’t be identified in the SIC-3G-GSM or SIC-HSPA.
Resolved problems in CMW520-R2209P15
RTD061429
Symptom: When modifying the parameter of tunnel bandwidth, OSPF COST doesn’t update.
Condition: The tunnel interface of the route runs OSPF protocol.
RTD61366
Symptom: The REINVITE message from the router doesn’t take NTE capacity filed, so the FAX passthrough with LYNC server fails.
Condition: The router runs FAX passthrough with Microsoft LYNC server.
RTD061122
Symptom: The router doesn’t eliminate the NAT session synchronously at the router, so that the NAT data flow can be transmitted all along.
Condition: Remove the NAT static configuration at the router, at the same time there are durative NAT data flow at the router.
Resolved problems in CMW520-R2209P13
RTD060728
Symptom: Some time, the E1-F interface is UP and DOWN ceaselessly.
Condition: A SIC-2E1-F card is inserted into the router, and the link status of one E1-F interface is UP, the link status of the other E1-F interface is DOWN.
RTD60727
Symptom: The router can’t detect the RPS power status accurately, so there are lots of
RPS power alarms at the LOG of the router.
Condition: The MSR30 router with RPS power.
RTD60660
Symptom: The pulse shape of MIM-8T1 and FIC-8T1 interface was too low.
Condition: None.
RTD60295
Symptom: The Power Spectral Density of the 4-Wire G.SHDL MIM can’t achieve compliance against S043 for Australia testing.
24
Condition: None.
RTD60295
Symptom: The Power Spectral Density of the 4-Wire G.SHDL MIM can’t achieve compliance against S043 for Australia testing.
Condition: None.
RTD60721
Symptom: Once the interface bearing the BGP connection is UP/DOWN, the BGP connection will be UP/DOWN again and again, and it takes a long time to establish the steady BGP connection.
Condition: There are lots of BGP route policies about community attribute at the router, and there are also many of BGP routes at the router.
RTD60720
Symptom: The GTS characteristics (CIR, CBS, EBS) based on the real bandwidth negotiated by the router on the display information are error.
Condition: Set the QoS GTS policy at the ATM interface of the router.
RTD060715
Symptom: When the called phone number is in the hunt-group, the caller cannot hear ring back and the call failed.
Condition: The router established SIP voice calls to VCX and hunt-group was set.
Resolved problems in CMW520-R2209P01
RTD60295
Symptom: The Power Spectral Density of the 4-Wire G.SHDL MIM can’t achieve compliance against S043.
Condition: None.
RTD60406
Symptom: The router rebooted abnormally.
Condition: Insert some USB facility which the router can’t support into the router.
RTD60172
Symptom: Certain instance, EC1261 doesn’t reply BULK OUT ACK to the router for two seconds, so the router can’t identify the EC1261.
Condition: The router connects HUAWEI EC1261 MODEM.
25
RTD60042
Symptom: After a long time, the FSW card can’t forward multicast and broadcast packets.
Condition: The 16FSW or 24FSW card at the router runs three layer packets, and the other interfaces of the router forward large numbers of packets.
RTD59961
Symptom: The Remote Alarm Indication (RAI) handling of SIC-EPRI doesn’t seem to work correctly, the test cases TC10102, TC10103, TC10105, TC10701, TC11105, TC11118 and TC12501 of TBR4 are all non-compliant.
Condition: None.
RTD59907
Symptom: E160 MODEM reboots again and again.
Condition: The router connects HUAWEI E160 MODEM.
RTD59895
Symptom: Period of time, The SIC-1T1-F card can’t receive and send packets, and the interface queue is plugged up.
Condition: The POE router is inserted into FSW-POE card and SIC-1T1-F card.
RTD60199
Symptom: The SNMP OID hh3cCfgLogTerminalUser value is error.
Condition: None.
Resolved problems in CMW520-R2209
RTD59161
Symptom: When transmits some UDP packets, the router will reboot abnormally.
Condition: The router runs NAT function, and there are several NAT outbound commands at the interface of the router.
RTD58793
Symptom: The result of NQA was inaccurate.
Condition: Run NQA function in the Multilink PPP link with several physical interfaces.
RTD58598
Symptom: The line protocol status of the async interface is always down.
Condition: The aysnc interface of the router works at flow mode.
26
RTD59306
Symptom: OSPF Area 0 ABR does not generate default to stub when no neighbor in
Area 0.
Condition: Run OSPF protocol in the router.
Resolved problems in CMW520-R2207P45
RTD58789
Symptom: If the router received challenge more than 16 bytes, the PPP CHAP authentication failed.
Condition: The interface of the router set PPP protocol and CHAP authentication.
RTD58508
Symptom: The router can’t identify the INARP packets with filled information, so the router failed to parse the IP address.
Condition: None.
RTD57556
Symptom: Because the BGP timer of the router was inaccurate, the BGP neighbors were UP and DOWN again and again.
Condition: The CPU usage of the router was high.
Resolved problems in CMW520-R2207P38
RTD58234
Symptom: The port will be shut down.
Condition: Insert a pseudo fiber module to a port of an HP A-MSR router.
RTD57850
Symptom: There wasn’t the command to adjust the cable attenuation parameters at the IMA-T1 interface of the router.
Condition: None.
RTD57858
Symptom: The pulse shape of IMA-T1 interface was too low.
Condition: None.
RTD58297
Symptom: The pulse shape of SIC-EPRI interface has overshot /undershot.
Condition: None.
27
RTD58164
Symptom: The pulse shape of IMA-E1 interface was too low.
Condition: None.
RTD57892
Symptom: When the router received the SIP packets which’s record-route and contact head field the Transfer Protocol were inconsistent, because the router selected the error Transfer Protocol the voice call failed。
Condition: The router as VOICE gateway connected with AYAYA .
RTD57811
Symptom: The dialer connection can’t establish.
Condition: The Dialer interface of the router set chap authentication for call-in connection.
RTD58221
Symptom: The router rebooted abnormally.
Condition: Execute the command of “display ip flow-ordering statistic internal” at the router.
Resolved problems in CMW520-R2207P34
RTD57852
Symptom: After the BFD session at the router was DOWN, the router would delete correlative RIP routes, but the router still sent the RIP packets from the interface. If the interface was broken down in the one direction, another end could still received the rip packets.
Condition: The router started RIP BFD function.
RTD57785
Symptom: If the router received the SIP messages which the contact filed of was included the maddr parameter, the voice call from the router was unsuccessful.
Condition: The router worked with some SIP SERVER, and established voice calls.
RTD57105
Symptom: The router reboots itself randomly.
Condition: The MSR30 router has 2 x 512M memories.
28
Resolved problems in CMW520-R2207P33
RTD57709
Symptom: The fax function couldn’t be started at the router.
Condition: None.
Resolved problems in CMW520-R2207P23
RTD57286
Symptom: Occasionally the router can’t recover from PPP state-machine and can’t dialup 3G-link successfully.
Condition: The router doesn’t receive connect information from 3G modem.
RTD57514
Symptom: The 3G interface of the router would be UP and DOWN.
Condition: 3G network was HSPA+.
RTD57364
Symptom: The fax function couldn’t be started at the router.
Condition: None.
RTD57365
Symptom: Because the SDP’s fmtp and rtpmap of the SIP packet negotiated by error, the compression selected was wrong.
Condition: The router established the SIP connection with other equipment.
RTD57500
Symptom: The packet which matching this route can’t be transmitted.
Condition: MPLS L3VPN, inter-AS option B, a route advertising to ASBR through different
VPN-instance and the route is flapping.
Resolved problems in CMW520-R2207P14
RTD56973
Symptom: The 3G interface would be UP and DOWN because 3G network was unstable.
Condition: 3G network status was unstable, little the network was no service.
29
RTD56986
Symptom: The router would turn off the FAX function, and brought on that the FAX failed.
Condition: The router received the SIP INVITE message without a=T38MaxBitRate filed to transfer T.38.
RTD56520
Symptom: Even though the RIP BFD session was down, the RIP routes were updated.
Condition: Configuring RIP BFD at the router, the link was uni-direction and the router could receive the RIP packets.
RTD56390
Symptom: The router couldn’t get the Calling number and Called Number attribute from LAC.
Condition: The router acted as LNS, and LAC sent the ICCN packets without Proxy auth attribute.
RTD56145
Symptom: Because the router didn’t take offset filed in the L2TP packets, the L2TP connection couldn’t establish.
Condition: The router acted as LNS, and LAC requested the L2TP packets received with offset field.
Resolved problems in CMW520-R2207P02
RTD56119
Symptom: The router will reboot possibly.
Condition: If change the DVPN tunnel-protocol when there is IP traffic going out of the tunnel.
RTD56062
Symptom: The IPSec policy groups cannot be modified successfully if the virtual interface is deleted first.
Condition: Apply two or more IPSec policy groups to a virtual interface on the web interface, like interface tunnel.
RTD56060
Symptom: The router made mistake when negotiating about the codec, it resulted in that the FAX failed.
Condition: The router received the SIP packet of “200 OK” without
“a=silenceSupp:off”.
30
RTD56106
Symptom: The DAR function was abnormal and couldn’t identify the packets correctly.
Condition: The packets were identified by DAR after the packets were transmitted through L2TP tunnel.
RTD55818
Symptom: The E1 POS calls failed.
Condition: The E1POS interface worked with ISDN signal, and established the ISDN connection with ALCATEL PBX.
RTD56103
Symptom: The A-MSR router as RTA client couldn’t establish connection with RTA relay.
Condition: The AR46 or AR28 router worked as RTA relay.
Resolved Problems in CMW520-R2207
RTD54811
Symptom: The instant message cannot be relaid.
Condition: When using UDP as the SIP transport protocol, If the Packet is huge, the
A-MSR cannot re-build the SIP fragment messages.
RTD54836
Symptom: The call cannot be established.
Condition: When configure the UDP as the SIP transport protocol, If the Packet is larger than MTU-200, the transport protocol will automatically change to TCP, but if the destination does not support TCP, the transport protocol cannot change back to UDP.
Resolved Problems in CMW520-R2105P38
RTD55551
Symptom: All isdn calls at the four SIC-BU cards couldn’t be established successfully at the same time.
Condition: There were four SIC-BU cards inserted into the router.
RTD55454
Symptom: After period of time, IPSEC data would be intermitted.
Condition: The router transmitted IPSEC data with perfect forward secrecy function.
31
RTD55494
Symptom: The static arp items are not buildrun after the arp fixup command, so the static arp items will be lost after the device reboot.
Condition: Run the arp fixup command and reboot the router.
Resolved Problems in CMW520-R2105P36
RTD54196
Symptom: Even if there were several sub-interfaces at the main-interface, only one x.121 address can be set to map x25 bridge.
Condition: Set x25 bridge map at the interface of the router.
RTD54728
Symptom: After mirroring the packets for a while, the memory of the router leaked.
Condition: The source port of mirror-group was MP’s virtual-template interface.
RTD54669
Symptom: The G.SHDSL interface still negotiated as 4-wire.
Condition: The G.SHDSL interface of the A-MSR 20-13 was set to 2-wire mode.
Resolved Problems in CMW520-R2105P35
RTD53977
Symptom: There were some lost packets at the high PRI queue even if the high priority packets didn’t exceed the bandwidth assigned.
Condition: The FR traffic shaping function was enabled at the FR interface, and the CIR of the DLCI was equal to the bandwidth of the interface, the QOS queues were set at the DLCI.
Resolved Problems in CMW520-R2105P31
RTD54152
Symptom: If the ARP entries updated, the sequence of static ARP entries saved changed.
Condition: Configure some static ARP entries at the router.
32
Resolved Problems in CMW520-R2105P26
RTD54042
Symptom: After doing the two operations simultaneity period of time, the router’s configuration file lost.
Condition: Execute the command “save” to save the configuration file at the router, at the same time put the configuration file to the router using TFTP.
RTD53983
Symptom: The packets transmitted by the interface can’t be translated correctly.
Condition: Certain interface of the router was bound to the VPN-instance, and was enabled the NAT function.
RTD53976
Symptom: If defining several PU facilities using the same MAC address, the router only could establish virtual circuit for one PU facility.
Condition: The two routers established the DLSw peer, and transmitted the packets between the IBM mainframe and SNA host.
RTD53848
Symptom: Even though the L2TP client was asynchronous PPP, the router still sent the
SLI control packets with ACCM option, and sometime this should bring on that the L2TP connection negotiated unsuccessfully.
Condition: The router acts as LNS established the L2TP connection with other equipment.
RTD53886
Symptom: Ping 900 bytes to 1500 bytes packets from the G.SHDSL interface, and there were lots of packet lost.
Condition: The FIC/MIM-G.SHDSL cards were inserted into the router, and the G.SHDSL interface established the connection with the Ericsson EDA u2530 DSLAM.
Resolved Problems in CMW520-R2105P22
RTD53762
Symptom: After running for period of time, the router couldn’t establish SIP voice call successfully.
Condition: The router acted as SIP voice gateway.
RTD53423
Symptom: The NQA jitter test result was incorrect.
33
Condition: The time zone or the summer-time was set at the router, and the router acted as NQA server or client inter-operated with the other equipment.
RTD53153
Symptom: The Windows PPTP connection couldn’t be established successfully, after the PPTP packets were transmitted by the router.
Condition: NAT function was enabled at the router.
RTD53779
Symptom: When the signal of VT1 interface is R2, Digital E&M, or LGS, only the timeslot
1-23 can be set.
Condition: None.
Resolved Problems in CMW520-R2105P12
RTD53005
Symptom: After the user succeeded to login through the local Portal server, the router rebooted exceptionally.
Condition: The local Portal server was enabled at the router.
RTD53154
Symptom: Because the OSFP MD5 authentication Sequence could reach to the maximum and overturn at the short time, the OSPF neighbor relationships broke down and re-established.
Condition: There were many OSPF neighbors be established at the router.
Resolved Problems in CMW520-R2105P06
RTD51595
Symptom: The packets can’t be forwarded m.
Condition: When configuration the interface of virtual-template as the output-interface of static route.
RTD52249
Symptom: The key of HWTACACS can’t more than 96 characters.
Condition: None
RTD52822
Symptom: The packets matched up the static route can’t be transmitted by the
Virtual-template interface, and the static route to Virtual-template was invalid.
Condition: The Virtual-template interface of the router connected a point-to-point network, and the Virtual-template interface was an output interface of a static route.
34
RTD52279
Symptom: The POS connections to the AUX interface failed.
Condition: Run the POS APP function at the AUX interface of the router.
RTD52833
Symptom: The caller name couldn’t be displayed at the called.
Condition: The VOIP function was enabled at the router, and the ISDN SETUP message from the PBX didn’t contain the caller name, instead the caller name was included at the following Facility message.
Resolved Problems in CMW520-R2105P02
RTD51702
Symptom: Then the router can’t recognize the USB 3G Modem.
Condition: Plug the USB 3G Modem in and reboot the router with empty configuration.
RTD51603
Symptom: The router will be crash when send packets of ICMP unreachable.
Condition: When configuration the command of “nat outbound” on the interface.
RTD51986
Symptom: The A-MSR 30-16 didn’t support the DMC function, and there is any command of DMC at the A-MSR 30-16.
Condition: None
RTD52094
Symptom: The NAS-IP can’t be set to the IP address ended with 255 at the router.
Condition: None.
RTD51965
Symptom: When the router received the especial DNS reverse-query packets, the router did the NAT translation, then the router rebooted abnormally.
Condition: Start the NAT function at the router.
RTD51715
Symptom: The Linux FTP client couldn’t visit the Serv-U ftp server transmitted by the router.
Condition: Enable the ASPF function at the router.
35
RTD51666
Symptom: Because the ADSL Modem XAVI model x7822m should send the ARP packets with 0000-0000-0000 MAC, the router can’t established the connection with this ADSL Modem.
Condition: None.
RTD51593
Symptom: If the ip address of the loopback interface is set before the ip address of another interface is set, the router can’t telnet the ip address of its loopback interface successfully.
Condition: There is a loopback interface and another interface which’s ip addres is the same IP network segment with the loopback interface.
RTD51592
Symptom: Because the router responded NAK packet when it received the MRRU more than 0x4000, the router can’t establish the connection with some equipment.
Condition: The router ran multilink PPP linked with some equipment.
RTD51760
Symptom: On the router direct route and LDP does not accept the label from the direct peer.
Condition: None.
Resolved Problems in CMW520-R2105
RTD51163
Symptom: Codec negotiation may be failed, and the call can not be setup.
Condition: When receiving a SIP message, if its SDP rtpmap and fmtp are not in order, the codec negotiation may be failed.
RTD51162
Condition: When neotiating T.38 in SIP Messages, after the negotiation, t.38 packets were not marked with DSCP.
Symptom: Because T.38 packets were not marked with DSCP, QoS policy may be mismatch and unuseful.
Related documentation
New feature documentation
None.
36
Documentation set
About the HP A-MSR Command References
About the HP A-MSR Configuration Guides
HP A-MSR Router Series ACL and QoS Command Reference
HP A-MSR Router Series ACL and QoS Configuration Guide
HP A-MSR Router Series Fundamentals Command Reference
HP A-MSR Router Series Fundamentals Configuration Guide
HP A-MSR Router Series High Availability Command Reference
HP A-MSR Router Series High Availability Configuration Guide
HP A-MSR Router Series IP Multicast Command Reference
HP A-MSR Router Series IP Multicast Configuration Guide
HP A-MSR Router Series IPX Command Reference
HP A-MSR Router Series IPX Configuration Guide
HP A-MSR Router Series Interface Command Reference
HP A-MSR Router Series Interface Configuration Guide
HP A-MSR Router Series Interface Modules Guide
HP A-MSR Router Series Layer 2 - LAN Switching Command Reference
HP A-MSR Router Series Layer 2 - LAN Switching Configuration Guide
HP A-MSR Router Series Layer 2 - WAN Command Reference
HP A-MSR Router Series Layer 2 - WAN Configuration Guide
HP A-MSR Router Series Layer 3 - IP Routing Command Reference
HP A-MSR Router Series Layer 3 - IP Routing Configuration Guide
HP A-MSR Router Series Layer 3 - IP Services Command Reference
HP A-MSR Router Series Layer 3 - IP Services Configuration Guide
HP A-MSR Router Series MPLS Command Reference
HP A-MSR Router Series MPLS Configuration Guide
HP A-MSR Router Series Network Management and Monitoring Command Reference
HP A-MSR Router Series Network Management and Monitoring Configuration Guide
HP A-MSR Router Series OAA Command Reference
HP A-MSR Router Series OAA Configuration Guide
HP A-MSR Router Series Security Command Reference
HP A-MSR Router Series Security Configuration Guide
HP A-MSR Router Series Terminal Access Command Reference
37
HP A-MSR Router Series Terminal Access Configuration Guide
HP A-MSR Router Series Voice Command Reference
HP A-MSR Router Series Voice Configuration Guide
HP A-MSR Router Series WLAN Command Reference
HP A-MSR Router Series WLAN Configuration Guide
HP A-MSR Router Series Web-Based Configuration Guide
Obtaining documentation
To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals
Technical support
[email protected] http://www.h3c.com
38
Appendix A Feature list
Hardware features
Table 5 A-MSR20-1X Series Hardware Features
Item
Dimensions (H x W x D)
A-MSR
20-10
Descriptio n
44.2mm
30
0mm 240m m
A-MSR
20-11
Description
44.2mm
300 mm 240mm
A-MSR
20-12
Descriptio n
44.2mm
30
0mm 240m m
Weight
Input AC voltage
3Kg 3Kg 3Kg
Rated voltage: 100 VAC to 240 VAC;
50 Hz/60 Hz
Input DC voltage Not support DC
Max power consumption
Operating temperature
Relative humidity
(noncondensing)
Processor
BootROM
FLASH
Memory
Externa l modul e
Internal modul e
SIC/
DSIC module
VPM strip
Consol e/AUX
USB
Fixed interfa ce
FE
FE switchi ng interfac e
25W
0°C to 40°C
5% to 90%
MSR 20-15
Description
44.2mm
300 mm 240mm
PowerPC
1MB
PowerPC
1MB
PowerPC
1MB
PowerPC
1MB
PowerPC
1MB
16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB
256MB 256MB 256MB 256MB 256MB
1
0
1
1
1 electrical interfaces
4
1
0
1
1
1 electrical interfaces
4
1
1
1
1
1 electrical interfaces
4
A-MSR
20-13
Descriptio n
44.2mm
30
0mm 240m m
3Kg
1
0
1
1
1 electrical interfaces
4
3Kg
1
1
1
1
1 electrical interfaces
4
1
ADSL
G.SHDS
L
SAE
ISDN
S/T
AM
E1/T1
0
0
0
0
0
0
0
0
1
0
0
0 option al
Wlan 1 0
Table 6 A-MSR20 Series Hardware Features
0
0
0
1
1
0
0
Item
Dimensions (H x W x
D)
Weight
Input AC voltage
Input DC voltage
Max power
A-MSR 20-20
Description
44.2mm
360mm
287.
1mm
A-MSR 20-21
Description
44.2mm
360mm
28
7.1mm
3.4Kg 3.4Kg
Rated voltage: 100 VAC to 240 VAC; 50/60 Hz
Not support DC
54W 54W
Operating temperature
Relative humidity
(noncondensing)
Processor
0°C to 40°C (32oF to 104oF)
5% to 90%
PowerPC
BootROM
Memory
CF CARD
External module
Internal module
SIC module
ESM module
2
1
VCPM module
0
VPM strip 0
Console 1
4MB
SDRAM
Default: 256MB
Maximum: 256MB
Default: 256MB
Maximum: 1GB
Fixed interfac e
AUX
USB
FE
1
1
Two electrical
PowerPC
4MB
SDRAM
Default: 256MB
Maximum: 256MB
Default: 256MB
Maximum: 1GB
2
1
0
0
1
1
1
Two electrical
1
0
0
1
0
1(G.SHDSL.
bis)
0
5.4Kg
100W
4
2
1
1
1
1
0
1
0
0
A-MSR 20-40
Description
44.2mm
442mm
407.1
mm
PowerPC
4MB
SDRAM
Default: 256MB
Maximum: 256MB
Default: 256MB
Maximum: 1GB
1
1
2
1
Two electrical
2
interfaces
FE switching interface
0
Table 7 A-MSR30 Series Hardware Features interfaces
8 interfaces
0
Item
Dimensions
(H x W x D)
Weight
Input AC voltage
MSR 30-11
Descriptio n
A-MSR 30-16
Description
A-MSR 30-20
Description
44.2mm×44
2 mm×360 mm
4.6Kg
44.2mm×442 mm×441.8mm
44.2mm×442 mm×441.8mm
6Kg 6.9Kg
Rated voltage: 100 VAC to 240 VAC;
50 Hz/60 Hz
A-MSR 30-40
Description
88.2mm×442 mm×422.3mm
11.9Kg
Input DC voltage
Not support
DC
Not support DC
Rated voltage:
-48V d.c.~-60V d.c
Rated voltage:
-48V d.c.~-60V d.c
125W 210W Max power 54W
Operating temperatur e
Relative humidity
(nonconde nsing)
0°C to 40°C
5% to 90%
Processor
BootROM
Memory
PowerPC
2MB
DDR
SDRAM
Default:
256MB
Maximum:
256MB
100W
PowerPC
4MB
DDR SDRAM
Default: 256MB
Maximum:
256MB
CF CARD 0
32MB
Default: 256MB
Maximum: 1GB
0
PowerPC
4MB
PowerPC
4MB
A-MSR
30-60
Descriptio n
132mm×442 mm×421.8m
m
13.6Kg
Rated voltage:
-48V d.c.~
-60V d.c
210W
PowerPC
4MB
DDR SDRAM
Default: 512MB
Maximum: 1GB
DDR SDRAM
Default: 512MB
Maximum: 1GB
DDR SDRAM
Default:
512MB
Maximum:
1GB
Default: 256MB
Maximum: 1GB
0
Default: 256MB
Maximum: 1GB
0
Default:
256MB
Maximum:
1GB
0
E xt e rn al m
FLASH
SIC modul e
DSIC modul e
2
0
4
2
4
2
4
2
4
2
3
o d ul e e rf in t
Fi x e d a c e
In t e rn al m o d ul e
VPM strip
Consol e
AUX
USB
FE
GE
SAE
MIM modul e
XMIM modul e
DMIM modul e
ESM modul e
VCPM modul e
1
1
0
1
0
0
1
1
0
2
0
1
0
0
2
1
2
1
1
1
2
0
2
0
0
2
1
2
1
1 0
Table 8 A-MSR30-1X Series Hardware Features
1
2
0
2 electrical interfaces
0
Item
Dimensions (H x W x
D)
Weight
Input AC voltage
Input DC voltage
Max power
Operating temperature
Relative humidity
(noncondensing)
Processor
BootROM
Memory
0°C to 40°C (32oF to 104oF)
5% to 90%
PowerPC
2MB
DDR SDRAM
Default: 256MB
PowerPC
2MB
DDR SDRAM
Default: 256MB
4
0
1
2
1
3
A-MSR 30-10
Description
44.2 mm×442 mm×360mm
A-MSR 30-11E
Description
44.2 mm×442 mm×360mm
4.8kg 4.5Kg
Rated voltage: 100 VAC to 240 VAC; 50/60 Hz
Rated voltage: –48
VDC to –60 VDC
54W
Not support DC
54W
1
1
2
0
2 Combo interfaces
0
A-MSR 30-11F
Description
44.2 mm×442 mm×360mm
4.8kg
Not support DC
54W
6
0
2
2
1
3
PowerPC
2MB
DDR SDRAM
Default: 256MB
1
1
2
0
2 Combo interfaces
0
4
CF CARD
FLASH
External module
Internal module
Fixed interfac e
Maximum: 256MB
Not support
256MB
SIC module
MIM module
2
1
XMIM module
1
ESM module
1
VPM strip 1
Console
AUX
USB
FE
1
1
1
Two electrical interfaces
FE switching interface
0
Table 9 A-MSR50 Series Hardware Features
Maximum: 256MB
Not support
256MB
2
1
0
1
0
1
1
1
Two electrical interfaces
24
Maximum: 256MB
Not support
256MB
2
1
0
1
0
1
1
1
Two electrical interfaces
48
Item
A-MSR 50-40
Description
A-MSR 50-40
MPU-G2
Description
130.7mm×436.2mm×424mm
A-MSR 50-60
Description
A-MSR 50-60
MPU-G2
Description
175.1mm×436.2mm×424mm
Dimensions (H x W x
D)
Weight
Input AC voltage
Input DC voltage
Max power
Operating temperature
Relative humidity
(noncondensing)
Processor
BootROM
Memory
CF CARD
18Kg 20Kg
Rated voltage: 100 VAC to 240 VAC; 50/60 Hz
Rated voltage: –48 VDC to –60 VDC
350W 350W
0°C to 40°C (32°F to 104°F)
5% to 90%
PowerPC
4MB
DDR SDRAM:
Default:
512MB
Max: 1GB
Default: 256MB
Max: 1GB
DDR SDRAM II:
Default: 1GB
Max: 2GB
PowerPC
4MB
DDR SDRAM:
Default: 512MB
Max: 1GB
Default: 256MB
Max: 1GB
DDR SDRAM II:
Default: 1GB
Max: 2GB
5
Item
Dimensions (H x W x
D)
Weight
Input AC voltage
Input DC voltage
Max power
Operating temperature
Relative humidity
(noncondensing)
Processor
BootROM
Memory
FLASH
External module
SIC module
MIM module
Internal ESM
External module
Internal module
Fixed interfac e
SIC module
FIC module
MSCA module
GE
4
4
1
ESM module
VCPM module
2
1
VPM strip
4
Console 1
AUX 1
USB
FE switchin g interfac e
2
0
2 COMBO interfaces
0
0
3 COMBO interfaces
Table 10 A-MSR 9XX Series Hardware Features
A-MSR 900 Description
44.2 mm×230 mm×160 mm
5~90% NO Dew
PowerPC
2MB
256MB
256MB
0
0
0
4
6
1
2
1
4
1
1
2
0
2 COMBO interfaces
0
0
3 COMBO interfaces
A-MSR 920 Description
44.2 mm×230 mm×160 mm
1.8Kg 1.8Kg
Rated voltage: 100 VAC to 240 VAC; 50/60 Hz
12V
15W 15W
0~40℃
PowerPC
2MB
256MB
256MB
0
0
0
6
module module
VPM strip 0
Fixed interfac e
Console/
AUX
USB
FE switching interface
FE
1
1
4
2
0
1
1
8
2
Table 11 A-MSR20_A-MSR30_A-MSR50_A-MSR900 series Module List
Module
SIC
Description
Ethernet interface cards:
JD573B HP A-MSR 4-port 10/100Base-T Switch SIC Module
JD620A HP A-MSR 4-port 10/100Base-T PoE Switch SIC Module
JD545B HP A-MSR 1-port 10/100Base-T SIC Module
JF280A HP A-MSR 1-port 100Base-X SIC Module
JD572A HP A-MSR 1-port GbE Combo SIC Module
JD634B HP A-MSR 1-port E1/Fractional E1 (75ohm) SIC Module
JD538A HP A-MSR 1-port T1/Fractional T1 SIC Module
JF842A HP A-MSR 2-port E1/Fractional E1 (75ohm) SIC Module
JD557A HP A-MSR 1-port Enhanced Sync/Async Serial SIC Module
JD536A HP 1-Port Analog Modem SIC A-MSR Module
JD537A HP A-MSR 1-port ADSL over POTS SIC Module
JD570A HP A-MSR 1-port ISDN-U SIC Module
JD571A HP A-MSR 1-port ISDN-S/T SIC Module
JF281A HP A-MSR 8-port Async Serial SIC Module
JF819A HP A-MSR 802.11b/g/n Wireless Access Point SIC Module
JF820A HP 3G Wireless GSM/WCDMA WAN SIC Module
JG211A HP A-MSR 802.11b/g/n Wireless Access Point SIC Module (NA)
JG056B HP A-MSR 1-port ADSL over ISDN SIC Module
JG186A HP A-MSR 16-port Async Serial SIC Module
JF253B HP A-MSR 1-port E1/CE1/PRI SIC Module
JG187A HP A-MSR HSPA/WCDMA SIC Module
Voice interface cards:
JD558A HP A-MSR 2-port FXO SIC Module
JD559A HP A-MSR 1-port FXO SIC Module
JD560A HP A-MSR 2-port FXS SIC Module
JD561A HP A-MSR 1-port FXS SIC Module
JD575A HP A-MSR 1-port E1 Voice SIC Module
JD576A HP A-MSR 1-port T1 Voice SIC Module
JF821A HP A-MSR 2-port ISDN-S/T Voice SIC Module
JD632A HP A-MSR 2-port FXS/1-port FXO SIC Module
7
DSIC
ESM
MIM
JD574B HP A-MSR 9-port 10/100Base-T Switch DSIC Module
JD621A HP A-MSR 9-port 10/100Base-T PoE Switch DSIC Module
JG189A HP A-MSR 4-port FXS/1-port FXO DSIC Module
JG191A HP A-MSR 1-port 8-wire G.SHDSL (RJ45) DSIC Module
JD608A HP A-MSR Advanced Network Data Encryption ESM Module
JD609A HP A-MSR Standard Network Data Encryption ESM Module
Ethernet interface cards:
JD613A HP A-MSR 2-port 10/100Base-T MIM Module
JD551A HP A-MSR 4-port 10/100Base-T MIM Module
JD548A HP A-MSR 2-port Gig-T MIM Module
JD569A HP 16-Port 10/100 MIM A-MSR Module
JD618A HP 16-Port 10/100 POE MIM A-MSR Module
JD540A HP A-MSR 2-port Enhanced Sync/Async Serial MIM Module
JD541A HP A-MSR 4-port Enhanced Sync/Async Serial MIM Module
JD552A HP A-MSR 8-port Enhanced Sync/Async Serial MIM Module
JF840A HP A-MSR 8-port Enhanced Async Serial MIM Module
JF841A HP A-MSR 16-port Enhanced Async Serial MIM Module
JD544A HP A-MSR 2-port E1/CE1/PRI MIM Module
JD549A HP A-MSR 2-port T1/CT1/PRI MIM Module
JD550A HP A-MSR 4-port E1/CE1/PRI MIM Module
JD556A HP A-MSR 4-port T1 IMA MIM Module
JD563A HP A-MSR 8-port E1/CE1/PRI (75ohm) MIM Module
JF255A HP A-MSR 8-port E1/Fractional E1 (75ohm) MIM Module
JC159A HP A-MSR 8-port T1/Fractional T1 MIM Module
JC160A HP A-MSR 8-port T1/CT1/PRI MIM Module
JD628A HP A-MSR 1-port T3/CT3/FT3 MIM Module
JD630A HP A-MSR 1-port E3/CE3/FE3 MIM Module
JD624A HP A-MSR 1-port OC-3c/STM-1c ATM SFP MIM Module
JD554A HP NDEC2 Encryption Accel MIM A-MSR Module
JD547A HP A-MSR 1-port 4-Wire G.SHDSL MIM Module
JG193AHP A-MSR 1-port OC-3c/STM-1c POS MIM Module
JF254B HP A-MSR 4-port T1/Fractional T1 MIM Module
JF257B HP A-MSR 4-port E1/Fractional E1 MIM Module
JD555B HP A-MSR 8-p E1 IMA (75ohm) MIM Module
Voice interface card:
JD543A HP A-MSR 2-port FXO MIM Module
JD542A HP A-MSR 4-port FXO MIM Module
JD553A HP A-MSR 4-port FXS MIM Module
JD565A HP A-MSR 1-port E1 Voice MIM Module
JD566A HP A-MSR 1-port T1 Voice MIM Module
JD567A HP A-MSR 2-port E1 Voice MIM Module
JD568A HP A-MSR 2-port T1 Voice MIM Module
JF822A HP A-MSR 16-port FXS MIM Module
JF837A HP A-MSR 4-port ISDN-S/T Voice MIM Module
8
DMIM
XMIM
VPM / VCPM
FIC
JD539A HP A-MSR 4-port E&M MIM Module
JD564A HP 24-Port 10/100 DMIM A-MSR Module
JD619A HP 24-Port 10/100 POE DMIM A-MSR Module
JF279A HP A-MSR 16-port 10/100Base-T Switch XMIM Module
JF276A HP A-MSR 24-port 10/100Base-T Switch XMIM Module
JD610A HP A-MSR Voice Co-processing Module
JD598A HP A-MSR 32-Channel Voice Processing Module
JD599A HP A-MSR 24-Channel Voice Processing Module
JD600A HP A-MSR 16-Channel Voice Processing Module
JD601A HP A-MSR 8-Channel Voice Processing Module
Ethernet interface cards:
JD583B HP A-MSR 1-port Gig-T FIC Module
JF260B HP A-MSR 8-port Enhanced Async Serial FIC Module
JF265B HP A-MSR 16-port Enhanced Async Serial FIC Module
JF269B HP A-MSR 2-port Gig-T FIC Module
JF270B HP A-MSR 2-port 1000Base-X FIC Module
JD582A HP A-MSR 1-port 1000Base-X FIC Module
JD577A HP A-MSR 2-port 10/100Base-T FIC Module
JF824A HP A-MSR 4-port 10/100Base-T FIC Module
JD604A HP 16-Port 10/100 FIC A-MSR Module
JD616A HP 16-Port 10/100 POE FIC A-MSR Module
JD584A HP A-MSR 4-port Enhanced Sync/Async Serial FIC Module
JD580A HP A-MSR 8-port Enhanced Sync/Async Serial FIC Module
JD578A HP A-MSR 2-port E1/CE1/PRI FIC Module
JD588A HP A-MSR 4-port E1/CE1/PRI FIC Module
JD585A HP A-MSR 8-port E1/CE1/PRI (75ohm) FIC Module
JD591A HP A-MSR 4-port E1/Fractional E1 FIC Module
JD592A HP A-MSR 4-port T1/Fractional T1 FIC Module
JD629A HP A-MSR 1-port T3/CT3/FT3 FIC Module
JD625A HP A-MSR 1-port E3/CE3/FE3 FIC Module
JD589A HP A-MSR 4-port Enhanced ISDN-S/T FIC Module
JD622A HP A-MSR 4-port E1 IMA (75ohm) FIC Module
JD595A HP A-MSR 1-port T3 ATM FIC Module
JD596A HP A-MSR 1-port E3 ATM FIC Module
JD633A HP A-MSR 1-port OC-3c/STM-1c ATM SFP FIC Module
JD581C HP A-MSR 1-port OC-3c/STM-1c POS FIC Module
JG201A HP A-MSR 1-port OC-3/STM-1 (E1/T1) CPOS FIC Module
JD586B HP A-MSR 8-port T1/CT1/PRI FIC Module
JG200A HP A-MSR 8-port T1 IMA FIC Module
JF278B HP A-MSR 8-p E1 IMA (75ohm) FIC Module
Voice interface cards:
JD602A HP A-MSR 4-port E&M FIC Module
JD593A HP A-MSR 4-port FXO FIC Module
JD594A HP A-MSR 4-port FXS FIC Module
9
D-FIC
JD605A HP A-MSR 1-port T1 Voice FIC Module
JD606A HP A-MSR 2-port T1 Voice FIC Module
JD607A HP A-MSR 1-port E1 Voice FIC Module
JD587A HP A-MSR 2-port E1 Voice FIC Module
JG197A HP A-MSR 24-port FXS FIC Module
JD603A HP 24-Port 10/100 DFIC A-MSR Module
JD617A HP 24-Port 10/100 POE DFIC A-MSR Module
CAUTION:
The support and restriction of modules on A-MSR please refer to HP A-MSR Router Series
Interface Module Guide, Appendix Purchase Guide.
Software features
Table 12 Software features of A-MSR20_A-MSR30_A-MSR50_A-MSR900 Series
Category
LAN protocol:
WAN protocols:
Features
ARP (proxy ARP, free ARP, authorization ARP)
Ethernet_II
Ethernet_SNAP
VLAN (PORT-BASED VLAN/MAC-BASED VLAN/VLAN-BASED PORT
ISOLATE/VLAN VPN/VOICE VLAN)
802.3x
LACP(802.3ad)
802.1p
802.1Q
802.1x
RSTP(802.1w)
MSTP(802.1s)
GVRP
PORT MUTILCAST suppression
PPP, MP
PPPoE Client, PPPoE Server
PPP/MP over FR
FR, MFR
FR Fragment, FR Compress, FR over IP
FRTS
ATM(IPoA, IPoEoA, PPPoA, PPPoEoA)
DCC, Dialer Watch
HDLC
LAPB
X25, X25 over TCP, X25 to TCP
X25 PAD, X25 Huntgroup, X25 CUG
10
IP services
Non-IP services:
IP application
IP route
MPLS
DLSW(V1.0/2.0)
ISDN, ISDN Network
ISDN QSIG
MODEM
Fast forwarding (unicast/multicast)
TCP
UDP
IP Option
IP unnumber
Policy routing (unicast/multicast)
SNA/DLSw support
DLSw Ethernet redundancy backup
IPX
Netstream
Ping and Trace
DHCP Server
DHCP Relay
DHCP Client
DNS client
DNS Static
NQA
IP Accounting
UDP Helper
NTP
Telnet
TFTP Client
FTP Client
FTP Server
Static routing management
Dynamic routing protocols:
RIP/RIPng
OSPF
OSPFv3
BGP
IS-IS
Multicast routing protocols:
IGMP
PIM-DM
PIM-SM
MBGP
MSDP
Routing policy
LDP
LSPM
11
IPv6
Port security
AAA
Firewall
Data security
Other security technologies
MPLS TE
MPLS FW
MPLS/BGP VPN
L2VPN
IPv6 basic functions
IPv6 ND
IPv6 PMTU
IPv6 FIB
IPv6 ACL
IPv6 transition technologies
NAT-PT
IPv6 tunneling
6PE
IPv6 routing
IPv6 static routing management
Dynamic routing protocols
RIPng
OSPFv3
IS-ISv6
BGP4+
Multicast routing protocols
MLD
PIM-DM
PIM-SM
PIM-SSM
PPPoE Client&Server
PORTAL
802.1x
Local authentication
Radius
HWTacacs
ASPF
ACL
FILTER
DDOS
IKE
IPSec
Encryption card
Portal/Portal+
L2TP
NAT/NAPT
PKI
RSA
SSH V1.5/2.0
12
Reliability
L2 QoS
Traffic supervision
Congestion management
Congestion avoidance
Traffic shaping
SSL (only support cooperate with CWMP)
URPF
GRE
DVPN
Supports VRRP
Supports the backup center
SP
WRED(Port)
CAR
LR
Flow-base QOS Policy
Port-Based Mirroring
Flow-Based Mirroring
Cos-Based HOLB(Head of Line Blocking)Prevention
Packet Remarking
Flow Redirect
Flow Accounting
Priority Mapping
Port Trust Mode
Port Priority
Flow Filter
FlowControl
ACL
Supports CAR (Committed Access Rate)
Supports LR (Line Rate)
FIFO, PQ, CQ, WFQ, CBQ, RTPQ
Other QOS technologies
Voice Interfaces
Voice Signaling
WRED/RED
Supports GTS(Generic Traffic Shaping)
FR QOS
MPLS QOS
MP QoS/LFI cRTP/IPHC
ATM QOS
Sub-interface QOS
FXS
FXO
E&M
E1VI/T1VI
R2
DSS1
Q.sig
Digital E&M
13
SIP
Codec
Media Process
FAX
Other
Network management
Local management
User access management
SIP
SIP Operation
G.711A law
G.711U law
G.723R53
G.723R63
G.729a
G.729R8
RTP/cRTP
IPHC
Voice Backup
FAX
Voice RADIUS
VoFR
Analog voice access and emergency
SNMP V1/V2c/V3
MIB
SYSLOG
RMON
Command line management
File system management
Dual Image
Supports console interface login
Supports AUX interface login
Supports TTY interface login
Supports telnet (VTY) login
Supports SSH login
Supports FTP login
Supports X25 PAD login
XMODEM
Appendix B Upgrading software
This section describes how to upgrade system software while the router is operating normally or when the router cannot correctly start up.
System software file types
System software images are in .bin format (for example, main.bin) and run at startup. You can set a system software image as a main, backup, or secure image.
At startup, the router always attempts to boot first with the main system software image. If the attempt fails, for example, because the image file is corrupted, the router tries to boot
14
with the backup system software image. If the attempt still fails, the router tries to boot with the secure system software image. If all attempts fail, the router displays a failure message.
Upgrade methods
You can upgrade system software by using one of the following methods:
Upgrade method
Upgrading from the BootWare menu
Software Upgrading Through Web
Remarks
You must reboot the router to complete the upgrade.
This method can interrupt ongoing network services.
Use this method when the router cannot correctly start up.
Provides a quick software upgrade method through Web.
Preparing for the upgrade
Before you upgrade system software, complete the following tasks:
Set up the upgrade environment as shown in Table 14 5
.
Configure routes to make sure that the router and the file server can reach each other.
Run a TFTP or FTP server on the file server.
Log in to the CLI of the router through the console port.
Copy the upgrade file to the file server and correctly set the working directory on the
TFTP or FTP server.
Make sure the upgrade has minimal impact on the network services. During the upgrade, the router cannot provide any services.
IMPORTANT:
In the BootWare menu, if you choose to download files over Ethernet, the Ethernet port must be ETH0 on an MSR900, MSR920, MSR20-1X, MSR20-20, MSR20-21, MSR20-24,
MSR30-10, MSR30-11E, MSR30-11F, and MSR30-16 router, and must be GE0 on an
MSR93X, MSR30-20, MSR30-40, MSR30-60, MSR50-40, and MSR50-60 router.
Table 13 Storage media
Model
MSR900 / 920
MSR93X
MSR20-1X
MSR20-20 / 20-21 / 20-40
MSR30-10 / 30-11E / 30-11F
MSR30-16 / 30-20 / 30-40 / 30-60
MSR50-40 / 50-60
Storage medium
Flash
Flash
Flash
CF card
Flash
CF card
CF card
Path flash:/ flash:/ flash:/ cfa0:/ flash:/ cfa0:/ cfa0:/
15
Figure 1 Set up the upgrade environment
192.168.1.2/24
TFTP/FTP
Server
192.168.1.1/24
Console cable
Upgrading from the CLI
You can use the TFTP or FTP commands on the router to access the TFTP or FTP server to back up or download files.
Using TFTP to upgrade software
This section describes how to upgrade system software by using TFTP.
Backing up the running system software image and configuration file
1.
2.
Perform the save command in any view to save the current configuration.
<HP> save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[cfa0:/startup.cfg]
(To leave the existing filename unchanged, press the enter key): cfa0:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait....
Configuration is saved to device successfully.
<HP>
Perform the dir command in user view to identify the system software image and configuration file names and verify that the CF card has sufficient space for the new system software image.
<HP> dir
Directory of cfa0:/
0 drw- - Jun 28 2012 14:41:16 logfile
1 drw- - Jun 28 2012 14:42:56 domain1
2 -rw- 16256 Jun 28 2012 14:43:40 p2p_default.mtd
3 -rw- 1694 Jun 28 2012 14:47:12 startup.cfg
4 -rw- 3432 Jun 28 2012 14:47:10 system.xml
5 -rw- 23861744 Jun 28 2012 14:37:46 main.bin
252328 KB total (227856 KB free)
16
3.
4.
File system type of cfa0: FAT16
<HP>
This example uses the default system software image file name main.bin and the default configuration file name startup.cfg.
Perform the tftp put command in user view to upload the main.bin file to the TFTP server.
<HP> tftp 192.168.1.1 put main.bin
File will be transferred in binary mode
Sending file to remote TFTP server. Please wait... \
TFTP: 23861744 bytes sent in 70 second(s).
File uploaded successfully.
<HP>
Perform the tftp put command in user view to upload the startup.cfg file to the TFTP server.
<HP> tftp 192.168.1.1 put startup.cfg
File will be transferred in binary mode
Sending file to remote TFTP server. Please wait... \
TFTP: 1694 bytes sent in 0 second(s).
File uploaded successfully.
<HP>
Upgrading the system software
1.
2.
3.
Perform the tftp get command in user view to download the system software image file, for example, MSR30-CMW520-R2207-SI.BIN to the CF card on the router.
<HP> tftp 192.168.1.1 get MSR30-CMW520-R2207-SI.BIN
File will be transferred in binary mode
Downloading file from remote TFTP server, please wait...|
TFTP: 23861744 bytes received in 70 second(s)
File downloaded successfully.
<HP>
Perform the boot-loader command in user view to load the file
MSR30-CMW520-R2207-SI.BIN and specify the file as the main image file at the next reboot.
<HP> boot-loader file msr30-cmw520-r2207-si.bin main
This command will set the boot file. Continue? [Y/N]:y
The specified file will be used as the main boot file at the next reboot on slot
0!
<HP>
Perform the display boot-loader command in user view to verify that the file has been loaded.
<HP> display boot-loader
The boot file used at this reboot:cfa0:/main.bin attribute: main
17
4.
5.
The boot file used at the next reboot:cfa0:/ msr30-cmw520-r2207-si.bin attribute: main
Failed to get the backup boot file used at the next reboot!
Failed to get the secure boot file used at the next reboot!
<HP>
Perform the reboot command in user view to reboot the router.
<HP> reboot
Start to check configuration with next startup configuration file, please wait.
........DONE!
This command will reboot the device. Continue? [Y/N]:y
#Jun 28 16:17:22:368 2012 HP DEVM/1/REBOOT:
Reboot device by command.
%Jun 28 16:17:22:368 2012 HP DEVM/5/SYSTEM_REBOOT: System is rebooting now.
Now rebooting, please wait...
<HP>
System is starting...
After the reboot is complete, perform the display version command to verify that the system software image is correct.
<HP>display version
HP Comware Platform Software
Comware Software, Version 5.20, Release 2207, Standard
Copyright (c) 2010-2012 Hewlett-Packard Development Company, L.P.
HP MSR30-20 uptime is 0 week, 0 day, 0 hour, 3 minutes
Last reboot 2012/06/28 16:19:05
System returned to ROM By <Reboot> Command.
CPU type: FREESCALE MPC8349 533MHz
256M bytes DDR SDRAM Memory
4M bytes Flash Memory
Pcb Version: 3.0
Logic Version: 2.0
Basic BootROM Version: 3.12
Extended BootROM Version: 3.13
[SLOT 0]CON (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]AUX (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/0 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/1 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]CELLULAR0/0 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
<HP>
Using FTP to upgrade software
This section describes how to upgrade system software by using FTP.
Backing up the running system software image and configuration file
1.
Perform the save command in any view to save the current configuration.
<HP> save
The current configuration will be written to the device. Are you sure? [Y/N]:y
18
2.
3.
4.
5.
Please input the file name(*.cfg)[cfa0:/startup.cfg]
(To leave the existing filename unchanged, press the enter key): cfa0:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait....
Configuration is saved to device successfully.
<HP>
Perform the dir command in user view to identify the system software image and configuration file names and verify that the CF card has sufficient space for the new system software image.
<HP> dir
Directory of cfa0:/
0 drw- - Jun 28 2012 14:41:16 logfile
1 drw- - Jun 28 2012 14:42:56 domain1
2 -rw- 16256 Jun 28 2012 14:43:40 p2p_default.mtd
3 -rw- 1694 Jun 28 2012 14:47:12 startup.cfg
4 -rw- 3432 Jun 28 2012 14:47:10 system.xml
5 -rw- 23861744 Jun 28 2012 14:37:46 main.bin
252328 KB total (227856 KB free)
File system type of cfa0: FAT16
<HP>
This example uses the default system software image file name main.bin and the default configuration file name startup.cfg.
Perform the ftp command in user view to access the FTP server.
<HP> ftp 192.168.1.1
Trying 192.168.1.1 ...
Press CTRL+K to abort
Connected to 192.168.1.1.
220 3Com 3CDaemon FTP Server Version 2.0
User(192.168.1.100:(none)):user001
331 User name ok, need password
Password:
230 User logged in
Perform the put command in FTP client view to upload the main.bin file to the FTP server.
[ftp] put main.bin
227 Entering passive mode (192,168,1,1,7,210)
125 Using existing data connection
226 Closing data connection; File transfer successful.
FTP: 23861744 byte(s) sent in 21.363 second(s), 1116.00Kbyte(s)/sec.
[ftp]
Perform the put command in FTP client view to upload the startup.cfg file to the FTP server.
[ftp] put startup.cfg
19
227 Entering passive mode (192,168,1,1,7,177)
125 Using existing data connection
226 Closing data connection; File transfer successful.
FTP: 1677 byte(s) sent in 0.142 second(s), 11.00Kbyte(s)/sec.
[ftp]
Upgrading the system software
1.
2.
3.
4.
5.
Perform the get command in FTP client view to download the system software image file MSR30-CMW520-R2207-SI.BIN to the CF card on the router.
[ftp] get msr20-cmw520-r2207-si.bin
227 Entering passive mode (192,168,1,1,7,225)
125 Using existing data connection
226 Closing data connection; File transfer successful.
FTP: 23861744 byte(s) received in 30.907 second(s), 772.00K byte(s)/sec.
[ftp]
Perform the quit command in FTP client view to return to user view.
[ftp]quit
221 Service closing control connection
<HP>
Perform the boot-loader command in user view to load the file
MSR30-CMW520-R2207-SI.BIN and specify the file as the main image file at the next reboot.
<HP> boot-loader file msr30-cmw520-r2207-si.bin main
This command will set the boot file. Continue? [Y/N]:y
The specified file will be used as the main boot file at the next reboot on slot
0!
<HP>
Perform the display boot-loader command in user view to verify that the file has been loaded.
<HP> display boot-loader
The boot file used at this reboot:cfa0:/main.bin attribute: main
The boot file used at the next reboot:cfa0:/ msr30-cmw520-r2207-si.bin attribute: main
Failed to get the backup boot file used at the next reboot!
Failed to get the secure boot file used at the next reboot!
<HP>
Perform the reboot command in user view to reboot the router.
<HP> reboot
Start to check configuration with next startup configuration file, please wait.
........DONE!
This command will reboot the device. Continue? [Y/N]:y
#Jun 28 16:17:22:368 2012 HP DEVM/1/REBOOT:
Reboot device by command.
%Jun 28 16:17:22:368 2012 HP DEVM/5/SYSTEM_REBOOT: System is rebooting now.
Now rebooting, please wait...
20
6.
<HP>
System is starting...
After the reboot is complete, perform the display version command to verify that the system software image is correct.
<HP>display version
HP Comware Platform Software
Comware Software, Version 5.20, Release 2207, Standard
Copyright (c) 2010-2012 Hewlett-Packard Development Company, L.P.
HP MSR30-20 uptime is 0 week, 0 day, 0 hour, 3 minutes
Last reboot 2012/06/28 16:19:05
System returned to ROM By <Reboot> Command.
CPU type: FREESCALE MPC8349 533MHz
256M bytes DDR SDRAM Memory
4M bytes Flash Memory
Pcb Version: 3.0
Logic Version: 2.0
Basic BootROM Version: 3.12
Extended BootROM Version: 3.13
[SLOT 0]CON (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]AUX (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/0 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/1 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
[SLOT 0]CELLULAR0/0 (Hardware)3.0 (Driver)1.0, (Cpld)2.0
<HP>
Upgrading from the BootWare menu
You can use the following methods to upgrade software from the BootWare menu:
Using TFTP/FTP to upgrade software through an Ethernet port
Using XMODEM to upgrade software through the console port
TIP:
Upgrading through an Ethernet port is faster than through the console port.
Accessing the BootWare menu
1.
Power on the router (for example, an HP MSR30-20 router), and you can see the following information:
System is starting...
Do you want to check SDRAM? [Y/N]
Booting Normal Extend BootWare........
The Extend BootWare is self-decompressing.....................
Done!
****************************************************************************
* *
21
2.
3.
* HP MSR30-20 BootWare, Version 4.0 *
* *
****************************************************************************
Copyright (c) 2004-2012 Hewlett-Packard Development Company, L.P.
Compiled Date : Feb 16 2012
CPU Type : MPC8349E
CPU L1 Cache : 32KB
CPU Clock Speed : 533MHz
Memory Type : DDR SDRAM
Memory Size : 256MB
Memory Speed : 264MHz
BootWare Size : 4096KB
Flash Size : 4MB cfa0 Size : 256MB
CPLD Version : 2.0
PCB Version : 3.0
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Press Ctrl + B at the prompt.
BootWare password: Not required. Please press Enter to continue.
Press Enter the BootWare password at the prompt to access the BootWare menu.
The current mode is password recovery.
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9):
Table 14 BootWare menu options
Item
<1> Boot System
Description
Boot the system software image.
22
Item
<2> Enter Serial SubMenu
<3> Enter Ethernet SubMenu
Description
Access the Serial submenu (see Table 17 ) for upgrading
system software through the console port or changing the serial port settings.
Access the Ethernet submenu (see Table 15 ) for
upgrading system software through an Ethernet port or changing Ethernet settings.
Access the File Control submenu (see Table 18 ) to
retrieve and manage the files stored on the router.
<4> File Control
<5> Restore to Factory Default
Configuration
<6> Skip Current System Configuration
<7> BootWare Operation Menu
<8> Clear Super Password
<9> Storage Device Operation
<0> Reboot
Restore to factory default configuration.
Start the router with the factory default configuration.
This is a one-time operation and does not take effect at the next reboot. You use this option when you forget the console login password.
Access the BootWare Operation menu for backing up, restoring, or upgrading BootWare. When you upgrade the system software image, BootWare is automatically upgraded. HP does not recommend upgrading
BootWare separately. This document does not cover using the BootWare Operation menu.
Clear all super passwords used for switching to higher user privilege levels.
By default, no super password is required for switching to a higher user privilege level.
Access the Storage Device Operation menu to manage storage devices. Using this option is beyond this chapter.
Restart the router.
Using TFTP/FTP to upgrade software through an Ethernet port
1.
Enter 3 in the BootWare menu to access the Ethernet submenu.
=========================<Enter Ethernet SubMenu>=========================
|Note:the operating device is cfa0 |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Update Backup Application File |
|<4> Update Secure Application File |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
==========================================================================
Enter your choice(0-5):
23
Table 15 Ethernet submenu options
Item
<1> Download Application Program To SDRAM
And Run
<2> Update Main Application File
<3> Update Backup Application File
<4> Update Secure Application File
<5> Modify Ethernet Parameter
Description
Download a system software image to the
SDRAM and run the image.
Upgrade the main system software image.
Upgrade the backup system software image.
Upgrade the secure system software image.
Modify network settings.
<0> Exit To Main Menu
2.
Return to the BootWare menu.
Enter 5 to configure the network settings.
=========================<ETHERNET PARAMETER SET>=========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
==========================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :main.bin
:
Target File Name :main.bin
:
Server IP Address :192.168.1.1
Local IP Address :192.168.1.253
Gateway IP Address :0.0.0.0
FTP User Name :user
FTP User Password :password
Table 16 Network parameter fields and shortcut keys
Field
'.' = Clear field
'-' = Go to previous field
Ctrl+D = Quit
Protocol (FTP or TFTP)
Load File Name
Target File Name
Server IP Address
Local IP Address
Gateway IP Address
FTP User Name
Description
Press a dot (.) and then Enter to clear the setting for a field.
Press a hyphen (-) and then Enter to return to the previous field.
Press Ctrl + D to exit the Ethernet Parameter Set menu.
Set the file transfer protocol to FTP or TFTP.
Set the name of the file to be downloaded.
Set a file name for saving the file on the router. By default, the target file name is the same as the source file name.
Set the IP address of the FTP or TFTP server. If a mask must be set, use a colon (:) to separate the mask length from the IP address. For example, 192.168.80.10:24.
Set the IP address of the router.
Set a gateway IP address if the router is on a different network than the server.
Set the username for accessing the FTP server. This username must be the same as configured on the FTP server. This field is not available for TFTP.
24
Field
FTP User Password
Description
Set the password for accessing the FTP server. This password must be the same as configured on the FTP server. This field is not available for TFTP.
3.
4.
Select an option in the Ethernet submenu to upgrade a system software image. For example, enter 2 to upgrade the main system software image.
Loading.....................................................................
............................................................................
.........................Done!
31911744 bytes downloaded!
Updating File flash:/main.bin...............................................
....................................................Done!
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Update Backup Application File |
|<4> Update Secure Application File |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5):
Enter 0 to return to the BootWare menu or 1 to boot the system.
Using XMODEM to upgrade software through the console port
1.
Enter 2 in the BootWare menu to access the Serial submenu.
===========================<Enter Serial SubMenu>===========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Update Backup Application File |
|<4> Update Secure Application File |
|<5> Modify Serial Interface Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5):
Table 17 Serial submenu options
Item
<1> Download Application Program To SDRAM
And Run
<2> Update Main Application File
<3> Update Backup Application File
Description
Download an application to SDRAM through the serial port and run the program.
Upgrade the main system software image.
Upgrade the backup system software image.
25
Item
<4> Update Secure Application File
<5> Modify Serial Interface Parameter
Description
Upgrade the secure system software image.
Modify serial port parameters
<0> Exit To Main Menu
2.
Return to the BootWare menu.
Select an appropriate baud rate for the console port. For example, enter 5 to select
115200 bps.
===============================<BAUDRATE SET>===============================
|Note:'*'indicates the current baudrate |
| Change The HyperTerminal's Baudrate Accordingly |
|---------------------------<Baudrate Available>---------------------------|
|<1> 9600(Default)* |
|<2> 19200 |
|<3> 38400 |
|<4> 57600 |
|<5> 115200 |
|<0> Exit |
============================================================================
Enter your choice(0-5):5
The following messages appear:
Baudrate has been changed to 115200 bps.
Please change the terminal's baudrate to 115200 bps, press ENTER when ready.
NOTE:
Typically the size of a .bin file is over 10 MB. Even at 115200 bps, the download takes about 30 minutes.
3.
Select Call > Disconnect in the HyperTerminal window to disconnect the terminal from the router.
Figure 2 Disconnect the terminal connection
4.
NOTE:
If the baud rate of the console port is 9600 bps, jump to step
Select File > Properties, and in the Properties dialog box, click Configure.
26
Figure 3 Properties dialog box
5.
Select 115200 from the Bits per second list and click OK.
27
Figure 4 Modify the baud rate
6.
Select Call > Call to reestablish the connection.
Figure 5 Reestablish the connection
7.
8.
Press Enter.
The following menu appears:
The current baudrate is 115200 bps
===============================<BAUDRATE SET>===============================
|Note:'*'indicates the current baudrate |
| Change The HyperTerminal's Baudrate Accordingly |
|---------------------------<Baudrate Available>---------------------------|
|<1> 9600(Default) |
|<2> 19200* |
|<3> 38400 |
|<4> 57600 |
|<5> 115200 |
|<0> Exit |
============================================================================
Enter your choice(0-5):
Enter 0 to return to the Serial submenu.
28
===========================<Enter Serial SubMenu>===========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Update Backup Application File |
|<4> Update Secure Application File |
|<5> Modify Serial Interface Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5):
9.
Select an option from options 2 to 4 to upgrade a system software image. For example, enter 2 to upgrade the main system software image.
Please Start To Transfer File, Press <Ctrl+C> To Exit.
10.
Waiting ...CCCCC
Select Transfer > Send File in the HyperTerminal window.
Figure 6 Transfer menu
11.
In the dialog box that appears, click Browse to select the source file, and select
Xmodem
from the Protocol list.
Figure 7 File transmission dialog box
12.
Click Send. The following dialog box appears:
29
Figure 8 File transfer progress
13.
When the Serial submenu appears after the file transfer is complete, enter 0 at the prompt to return to the BootWare menu.
Download successfully!
31911808 bytes downloaded!
Input the File Name:main.bin
Updating File flash:/main.bin..............................................
.....................................................Done!
===========================<Enter Serial SubMenu>===========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Update Backup Application File |
|<4> Update Secure Application File |
|<5> Modify Serial Interface Parameter |
|<0> Exit To Main Menu |
============================================================================
14.
15.
Enter your choice(0-5):
Enter 1 in the BootWare menu to boot the system.
If you are using a download rate other than 9600 bps, change the baud rate of the terminal to 9600 bps. If the baud rate has been set to 9600 bps, skip this step.
Managing files from the BootWare menu
To change the type of a system software image, retrieve files, or delete files, enter 4 in the
BootWare menu.
The File Control submenu appears:
==============================<File CONTROL>==============================
|Note:the operating device is cfa0 |
|<1> Display All File(s) |
30
|<2> Set Application File type |
|<3> Set Configuration File type |
|<4> Delete File |
|<0> Exit To Main Menu |
==========================================================================
Enter your choice(0-4):
Table 18 File Control submenu options
Item
<1> Display All File
<2> Set Application File type
<3> Set Configuration File type
<4> Delete File
<0> Exit To Main Menu
Description
Display all files.
Change the type of a system software image.
Change the type of a configuration file.
Delete files.
Return to the BootWare menu.
Displaying all files
To display all files, enter 1 in the File Control submenu:
Display all file(s) in cfa0:
'M' = MAIN 'B' = BACKUP 'S' = SECURE 'N/A' = NOT ASSIGNED
==========================================================================
|NO. Size(B) Time Type Name |
|1 640199 May/20/2012 09:53:16 N/A cfa0:/logfile/logfile.log |
|2 22165484 May/20/2012 09:18:10 B+S cfa0:/update.bin |
|3 1181 May/20/2012 09:42:54 N/A cfa0:/startup.cfg |
|4 22165484 May/20/2012 09:42:28 M cfa0:/main.bin |
==========================================================================
Changing the type of a system software image
System software image file attributes include main (M), backup (B), and secure (S). You can store only one main image, one backup image, and one secure image on the router.
A system software image can have any combination of the M, B, and S attributes. If the file attribute you are assigning has been assigned to an image, the assignment removes the attribute from that image. The image is marked as N/A if it has only that attribute.
For example, the file main.bin has the M attribute and the file update.bin has the S attribute.
After you assign the M attribute to update.bin, the type of update.bin changes to M+S and the type of main.bin changes to N/A.
NOTE:
You cannot remove or assign the S attribute in the File Control submenu.
To change the type of a system software image:
1.
Enter 2 in the File Control submenu.
'M' = MAIN 'B' = BACKUP 'S' = SECURE 'N/A' = NOT ASSIGNED
==========================================================================
|NO. Size(B) Time Type Name |
31
2.
3.
|1 22165484 May/20/2012 09:18:10 B+S cfa0:/update.bin |
|2 22165484 May/20/2012 09:42:28 M cfa0:/main.bin |
|0 Exit |
========================================================================
Enter file No:
Enter the number of the file you are working with, and press Enter.
Modify the file attribute:
==========================================================================
|<1> +Main |
|<2> -Main |
|<3> +Backup |
|<4> -Backup |
|<0> Exit |
==========================================================================
Enter your choice(0-4):
Enter a number in the range of 1 to 4 to add or delete a file attribute for the file.
Set the file attribute success!
Deleting files
When storage space is insufficient, you can delete obsolete files to free up storage space.
To delete files:
1.
Enter 4 in the File Control submenu.
Deleting the file in cfa0:
'M' = MAIN 'B' = BACKUP 'S' = SECURE 'N/A' = NOT ASSIGNED
2.
3.
==========================================================================
|NO. Size(B) Time Type Name |
|1 640199 May/20/2012 09:53:16 N/A cfa0:/logfile/logfile.log |
|2 22165484 May/20/2012 09:18:10 B+S cfa0:/update.bin |
|3 1181 May/20/2012 09:42:54 N/A cfa0:/startup.cfg |
|4 22165484 May/20/2012 09:42:28 M cfa0:/main.bin |
|0 Exit |
==========================================================================
Enter file No:
Enter the number of the file to delete.
When the following prompt appears, enter Y.
The file you selected is cfa0:/backup.bak,Delete it? [Y/N]Y
Deleting........Done!
Handling software upgrade failures
If a software upgrade fails, the system runs the old software version. To handle a software failure:
1.
Check the physical ports for a loose or incorrect connection.
32
4.
5.
6.
2.
3.
If you are using the console port for file transfer, check the HyperTerminal settings
(including the baud rate and data bits) for any wrong setting.
Check the file transfer settings:
If XMODEM is used, you must set the same baud rate for the terminal as for the console port.
If TFTP is used, you must enter the same server IP addresses, file name, and working directory as set on the TFTP server.
If FTP is used, you must enter the same FTP server IP address, source file name, working directory, and FTP username and password as set on the FTP server.
Check the FTP or TFTP server for any incorrect setting.
Check that the storage device has sufficient space for the upgrade file.
If the message “Something is wrong with the file” appears, check the file for file corruption.
Software Upgrading Through Web
The device obtains the target application file in the user-defined path through HTTP and has the system upgraded to the target version at the next reboot.
Select System Management > Software Upgrade from the navigation tree to enter the page as shown below.
Click Browse. On the dialog box displayed, select the target application file in the local path, and specify the name of the application file to be stored on the device. Then select the If the file with same name exists, overwrite it out remind check box. Click Apply to upgrade the software, as shown in the following figure.
33
The upgrade process takes about three to five minutes. During this process, ensure that the network connection is normal and do not power off or restart the device.
After the upgrade is complete, the system displays the following information and you need to restart the device.
34
Before restarting the device, follow these steps to save the current system configuration: select System Management > Configuration from the navigation tree to enter the default
Save page, and then click Save Current Settings, as shown in the following figure.
Click Yes in the pop-up dialog box.
After saving the configuration information, select System Management > Reboot from the navigation tree to enter the page shown below. Click Apply to reboot the device.
35
Appendix C Dealing with console login password loss and user privilege level password loss
CAUTION:
Dealing with console login password loss and user privilege level password loss from
BootWare menus is disruptive.
How to deal with console login password loss and user privilege level password loss
depends on the state of password recovery capability (see Figure 9 ). Password recovery
capability controls console user access to the device configuration and NVRAM from
BootWare menus.
If password recovery capability is enabled, a console user can access the device configuration without authentication and configure new passwords.
If password recovery capability is disabled, a console user must restore the factory-default configuration before configuring new passwords. Restoring the factory-default configuration deletes the main and backup next-startup configuration files.
To enhance system security, disable password recovery capability.
36
Figure 9 Dealing with password loss
Password lost
Reboot the router to access
EXTEND-BOOTWARE menu
Console login password lost
Yes
Password recovery capability enabled?
User privilege level password lost
Enter 6 to skip console login authentication
Enter 8 to clear user privilege level password
No
Enter 5 to restore the factory-default configuration
Reboot the router
Configure new passwords in system view
Save the running configuration
Examining the state of password recovery capability
1.
Reboot the router.
System is starting...
Press Ctrl+D to Access BASIC-BOOTWARE MENU..........................
****************************************************************************
* *
* HP MSR30-20 BootWare, Version 4.0 *
* *
****************************************************************************
Copyright (c) 2004-2012 Hewlett-Packard Development Company, L.P.
Compiled Date : Feb 16 2012
CPU Type : MPC8349E
CPU L1 Cache : 32KB
CPU Clock Speed : 533MHz
Memory Type : DDR SDRAM
Memory Size : 256MB
Memory Speed : 266MHz
BootWare Size : 4096KB
Flash Size : 4MB cfa0 Size : 256MB
CPLD Version : 2.0
PCB Version : 3.0
37
2.
3.
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Press Ctrl + B within three seconds after the "Press Ctrl+B to enter extended boot menu..." prompt message appears.
BootWare password: Not required. Please press Enter to continue.
Press Enter and read the password recovery capability state message displayed before the EXTEND-BOOTWARE menu.
The current mode is password recovery.
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9):
Dealing with console login password loss when password recovery capability is enabled
4.
Reboot the router to access the EXTEND-BOOTWARE menu, and then enter 6.
The current mode is password recovery.
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
38
5.
6.
7.
8.
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6
After the configuration skipping flag is set successfully, the following message appears:
Flag Set Success.
When the EXTEND-BOOTWARE menu appears again, enter 0 to reboot the router.
The router starts up with empty configuration.
To use the configuration in the next-startup configuration file, load the file in system view.
<HP> system-view
[HP] configuration replace file startup.cfg
Current configuration will be lost, save current configuration? [Y/N]:n
Info: Now replacing the current configuration. Please wait...
Info: Succeeded in replacing current configuration with the file startup.cfg.
Configure a new console login password.
In the following example, the console login authentication mode is password and the authentication password is 123456. For security, the password is always saved in ciphertext to the configuration file, regardless of whether you specify the simple keyword or cipher keyword for the set authentication password command.
<HP> system-view
[HP] user-interface console 0
[HP-ui-console0] authentication-mode password
[HP-ui-console0] set authentication password cipher 123456
To make the settings take effect after a reboot, save the running configuration to the next-startup configuration file.
[HP] save
Dealing with user privilege level password loss when password recovery capability is enabled
9.
Reboot the router to access the EXTEND-BOOTWARE menu, and then enter 8.
The current mode is password recovery.
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
39
10.
11.
12.
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 8
The router deletes the user privilege level password configuration commands from the main next-startup configuration file. After the operation is completed, the following message appears:
Clear Super Password Success!
When the EXTEND-BOOTWARE menu appears again, enter 0 to reboot the router.
The router starts up with the main next-startup configuration file.
Configure new passwords for user privilege levels.
In the following example, the password 123456 is configured for user privilege level 3.
For security, the password is always saved in ciphertext to the configuration file, regardless of whether you specify the simple keyword or cipher keyword for the super password
command.
<HP> system-view
[HP] super password cipher 123456
To make the setting take effect after a reboot, save the running configuration to the next-startup configuration file.
[HP] save
Dealing with password loss when password recovery capability is disabled
13.
Reboot the router to access the EXTEND-BOOTWARE menu, and enter 5.
The current mode is no password recovery.
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 5
40
14.
15.
16.
17.
At the prompt for confirmation, enter Y.
The router deletes its main and backup next-startup configuration files and restores the factory-default configuration.
The current mode is no password recovery. The configuration files will be deleted, and the system will start up with factory defaults, Are you sure to
continue?[Y/N]Y
Setting...Done.
When the EXTEND-BOOTWARE menu appears again, enter 0 to reboot the router.
The router starts up with the factory-default configuration.
Configure a new console login password (see " Configure a new console login password.
") or new user privilege level passwords (see " Configure new passwords for user privilege levels.
To make the settings take effect after a reboot, save the running configuration to the next-startup configuration file.
[HP] save
41
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Important information
- 6 Version information
- 6 Version number
- 6 Version history
- 14 Hardware and software compatibility matrix
- 17 Upgrading restrictions and guidelines
- 17 Hardware feature updates
- 17 CMW520-R2312P
- 17 CMW520-E
- 17 Software feature and command updates
- 18 MIB updates
- 22 Operation changes
- 22 Restrictions and cautions
- 22 Open problems and workarounds
- 23 List of resolved problems
- 23 Resolved problems in CMW520-R2312P
- 24 Resolved problems in CMW520-R
- 25 Resolved problems in CMW520-E
- 25 Resolved problems in CMW520-R2209P
- 28 Resolved problems in CMW520-R
- 29 Resolved problems in CMW520-R2207P
- 33 Resolved Problems in CMW520-R
- 33 Resolved Problems in CMW520-R2105P
- 38 Resolved Problems in CMW520-R
- 38 Related documentation
- 38 New feature documentation
- 39 Documentation set
- 40 Obtaining documentation