Bosch | UML-172-90 | User's Manual | Bosch UML-172-90 User's Manual

High Performance LCD Monitors
UML-172-90 | UML-192-90 | UML-202-90
en
Installation Manual
High Performance LCD Monitors
Table of Contents | en
iii
Table of Contents
1
Safety
1
1.1
Important Safety Instructions
1
1.2
Safety Precautions
4
1.3
Important Notices
4
1.4
Customer Support and Service
2
Unpacking
13
2.1
Parts List
13
2.2
Exploded View
14
2.3
Remote Control
16
2.4
Remote Control Battery Installation
17
3
Description
19
11
3.1
Features
19
3.2
Power
20
4
Installing the Monitor
21
4.1
Ventilation
21
4.2
Mounting the Monitor
21
4.2.1
Desktop Installation
21
4.2.2
Wall Mount Installation
22
4.3
Connecting the Composite Video Signal to the Monitor
22
4.4
Connecting the Y/C (S-Video) Signal to the Monitor
23
4.5
Connecting Audio to the Monitor
23
4.5.1
Connecting PC Audio
23
4.6
Connecting the PC Signal to the Monitor
24
4.6.1
HDMI
24
4.6.2
DVI
24
4.6.3
VGA
24
4.7
Connecting an Alarm Trigger
25
4.8
Single / Multiple Monitor Configuration
27
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 2.0 | 2009.03
iv
en | Table of Contents
High Performance LCD Monitors
5
Navigating the Monitor
29
5.1
Navigating the Front Panel
29
5.2
Navigating the Monitor On-screen Display (OSD)
29
5.3
On-screen Display Menus
31
5.4
Custom Menu
31
5.5
Picture / Sound Menu
33
5.6
PIP Menu
35
5.7
Setup Menu
36
5.7.1
Configuring Alarm Relay Inputs
37
5.7.2
Configuring Auto Switching
39
6
Power Management
41
6.1
Power Consumption
41
6.2
LED Indicator
41
7
Maintenance
43
8
TroubleShooting Guide
45
F.01U.076.723 | 2.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
1
Safety
1.1
Important Safety Instructions
1
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
1.
Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a dry cloth for cleaning is sufficient, but a moist flufffree cloth or leather shammy may also be used. Do not use
liquid cleaners or aerosol cleaners.
2.
Heat Sources - Do not install the unit near any heat
sources such as radiators, heaters, stoves, or other
equipment (including amplifiers) that produce heat.
3.
Ventilation - Any openings in the unit enclosure are
provided for ventilation to prevent overheating and ensure
reliable operation. Do not block or cover these openings.
Do not place the unit in an enclosure unless proper
ventilation is provided, or the manufacturer's instructions
have been adhered to.
4.
Water - Do not use this unit near water, for example near a
bathtub, washbowl, sink, laundry basket, in a damp or wet
basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To
reduce the risk of fire or electrical shock, do not expose
this unit to rain or moisture.
5.
Object and liquid entry - Never push objects of any kind
into this unit through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electrical shock. Never spill liquid of any
kind on the unit. Do not place objects filled with liquids,
such as vases or cups, on the unit.
6.
Lightning - For added protection during a lightning storm,
or when leaving this unit unattended and unused for long
periods, unplug the unit from the wall outlet and
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
2
en | Safety
High Performance LCD Monitors
disconnect the cable system. This will prevent damage to
the unit from lightning and power line surges.
7.
Controls adjustment - Adjust only those controls specified
in the operating instructions. Improper adjustment of
other controls may cause damage to the unit. Use of
controls or adjustments, or performance of procedures
other than those specified, may result in hazardous
radiation exposure.
8.
Overloading - Do not overload outlets and extension cords.
This can cause fire or electrical shock.
9.
Power cord and plug protection - Protect the plug and
power cord from foot traffic, being pinched by items
placed upon or against them at electrical outlets, and its
exit from the unit. For units intended to operate with
230 VAC, 50 Hz, the input and output power cord must
comply with the latest versions of IEC Publication 227 or
IEC Publication 245.
10. Power disconnect - Units with or without ON/OFF
switches have power supplied to the unit whenever the
power cord is inserted into the power source; however,
the unit is operational only when the ON/OFF switch is in
the ON position. The power cord is the main power
disconnect device for switching off the voltage for all units.
11. Power sources - Operate the unit only from the type of
power source indicated on the label. Before proceeding,
be sure to disconnect the power from the cable to be
installed into the unit.
–
For battery powered units, refer to the operating
instructions.
–
For external power supplied units, use only the
recommended or approved power supplies.
–
For limited power source units, this power source
must comply with EN60950. Substitutions may
damage the unit or cause fire or shock.
–
For 24 VAC units, voltage applied to the unit's power
input should not exceed ±10%, or 28 VAC. Usersupplied wiring must comply with local electrical
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
3
codes (Class 2 power levels). Do not ground the
supply at the terminals or at the unit's power supply
terminals.
–
If unsure of the type of power supply to use, contact
your dealer or local power company.
12. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
13. Damage requiring service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel when any damage to the equipment has
occurred, such as:
–
the power supply cord or plug is damaged;
–
exposure to moisture, water, and/or inclement
weather (rain, snow, etc.);
–
liquid has been spilled in or on the equipment;
–
an object has fallen into the unit;
–
unit has been dropped or the unit cabinet is damaged;
–
unit exhibits a distinct change in performance;
–
unit does not operate normally when the user
correctly follows the operating instructions.
14. Replacement parts - Be sure the service technician uses
replacement parts specified by the manufacturer, or that
have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical
shock, or other hazards.
15. Safety check - Safety checks should be performed upon
completion of service or repairs to the unit to ensure
proper operating condition.
16. Installation - Install in accordance with the manufacturer's
instructions and in accordance with applicable local codes.
17. Attachments, changes or modifications - Only use
attachments/accessories specified by the manufacturer.
Any change or modification of the equipment, not
expressly approved by Bosch, could void the warranty or,
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
4
en | Safety
High Performance LCD Monitors
in the case of an authorization agreement, authority to
operate the equipment.
1.2
Safety Precautions
WARNING! High risk:
This symbol indicates an imminently hazardous situation such
as “Dangerous Voltage” inside the product. If not avoided, this
will result in an electrical shock, serious bodily injury, or death.
!
WARNING! Medium risk:
Indicates a potentially hazardous situation. If not avoided, this
could result in serious bodily injury or death.
CAUTION! Medium risk:
Indicates a potentially hazardous situation. If not avoided, this
may result in minor or moderate injury. Alerts the user to
important instructions accompanying the unit.
!
WARNING! Low risk: (without safety alert symbol)
Indicates a potentially hazardous situation. If not avoided, this
may result in property damage or risk of damage to the unit.
NOTICE!
i
1.3
This symbol indicates information or a company policy that
relates directly or indirectly to the safety of personnel or
protection of property.
Important Notices
Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious
injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer.
When a cart is used, use caution and care when moving the
cart/apparatus combination to avoid injury from tip-over. Quick
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
5
stops, excessive force, or uneven surfaces may cause the cart/
unit combination to overturn. Mount the unit per the
manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building.
If it is needed to open the housing for servicing and/or other
activities, use this all-pole switch as the main disconnect device
for switching off the voltage to the unit.
Coax grounding:
–
Ground the cable system if connecting an outside cable
system to the unit.
–
Connect outdoor equipment to the unit's inputs only after
this unit has had its grounding plug connected to a
grounded outlet or its ground terminal is properly
connected to a ground source.
–
Disconnect the unit's input connectors from outdoor
equipment before disconnecting the grounding plug or
grounding terminal.
–
Follow proper safety precautions such as grounding for
any outdoor device connected to this unit.
U.S.A. models only - Section 810 of the National Electrical Code,
ANSI/NFPA No.70, provides information regarding proper
grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors,
location of discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
NOTICE!
i
This device is intended for use in public areas only.
U.S. federal law strictly prohibits surreptitious recording of oral
communications.
Your Bosch product was developed and manufactured with
high-quality material and components that can be recycled and
reused. This symbol means that electronic and electrical
appliances, which have reached the end of their working life,
must be collected and disposed of separately from household
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
6
en | Safety
High Performance LCD Monitors
waste material. Separate collecting systems are usually in place
for disused electronic and electrical products. Please dispose
of these units at an environmentally compatible recycling
facility, per European Directive 2002/96/EC.
Environmental statement - Bosch has a strong commitment
towards the environment. This unit has been designed to
respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET
handling precautions to avoid electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper
ESD safety precautions when handling the electrostaticsensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch
circuit protection must be secured with a maximum fuse rating
of 16A. This must be in accordance with NEC800 (CEC Section
60).
Grounding and polarization - This unit may be equipped with a
polarized alternating current line plug (a plug with one blade
wider than the other blade). This safety feature allows the plug
to fit into the power outlet in only one way. If unable to insert
the plug fully into the outlet, contact a locally certified
electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding
plug (a plug with a third pin for earth grounding). This safety
feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally
certified electrician to replace the obsolete outlet. Do not
defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move
the unit with care. Excessive force or shock may damage the
unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially
regarding clearance from power and lightning conductors and
transient protection, must be in accordance with NEC725 and
NEC800 (CEC Rule 16-224 and CEC Section 60).
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
7
Permanently connected equipment - Incorporate a readily
accessible disconnect device in the building installation wiring.
Pluggable equipment - Install the socket outlet near the
equipment so it is easily accessible.
Power disconnect - Units have power supplied whenever the
power cord is inserted into the power source. The power cord
is the main power disconnect for all units.
Power lines - Do not locate the camera near overhead power
lines, power circuits, or electrical lights, nor where it may
contact such power lines, circuits, or lights.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV)
circuits. SELV circuits should only be connected to other SELV
circuits.
Because the ISDN circuits are treated like telephone-network
voltage, avoid connecting the SELV circuit to the Telephone
Network Voltage (TNV) circuits.
Video loss - Video loss is inherent to digital video recording;
therefore, Bosch Security Systems cannot be held liable for any
damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security
Systems recommends multiple, redundant recording systems,
and a procedure to back up all analog and digital information.
NOTICE!
i
This is a class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only, CLASS A)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following conditions:
–
this device may not cause harmful interference, and
–
this device must accept any interference received,
including interference that may cause undesired operation.
Note
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
8
en | Safety
High Performance LCD Monitors
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of Industry Canada. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and radiates
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct
the interference at his expense.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
INFORMATIONS FCC ET ICES (commercial applications)
(modèles utilisés aux États-Unis et au Canada uniquement,
CLASSE A)
Ce produit est conforme aux normes FCC partie 15. la mise en
service est soumises aux deux conditions suivantes:
–
cet appareil ne peut pas provoquer d'interférence nuisible
et
–
cet appareil doit pouvoir tolérer toutes les interférences
auxquelles il est soumit, y compris les interférences qui
pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est
révélé conforme aux exigences imposées aux appareils
numériques de Classe A en vertu de la section 15 du règlement
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
9
de la Commission fédérale des communications des États-Unis
(FCC). Ces contraintes sont destinées à fournir une protection
raisonnable contre les interférences nuisibles quand l'appareil
est utilisé dans une installation commerciale. Cette appareil
génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux
instructions, générer des interférences nuisibles aux
communications radio. L’utilisation de ce produit dans une
zone résidentielle peut provoquer des interférences nuisibles.
Le cas échéant, l’utilisateur devra remédier à ces interférences
à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un
technicien qualifié en radio/télévision, qui procédera à une
opération corrective. La brochure suivante, publiée par la
Commission fédérale des communications (FCC), peut s’avérer
utile : « How to Identify and Resolve Radio-TV Interference
Problems » (Comment identifier et résoudre les problèmes
d’interférences de radio et de télévision). Cette brochure est
disponible auprès du U.S. Government Printing Office,
Washington, DC 20402, États-Unis, sous la référence n° 004000-00345-4.
AVERTISSEMENT: Ce produit est un appareil de Classe A. Son
utilisation dans une zone résidentielle risque de provoquer des
interférences. Le cas échéant, l’utilisateur devra prendre les
mesures nécessaires pour y remédier.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Closed
Circuit Television Equipment, UL 2044. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
10
en | Safety
High Performance LCD Monitors
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL 60950-1. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
Copyright
This user guide is the intellectual property of Bosch Security
Systems, Inc. and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and must be
treated accordingly.
NOTICE!
This user guide has been compiled with great care and the
information it contains has been thoroughly verified. The text
i
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
1.4
Safety | en
11
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security
Systems Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Repair Center
Telephone: 800-566-2283
Fax: 800-366-1329
E-mail: repair@us.bosch.com
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
E-mail: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
E-mail: technical.support@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500
Fax: 31 (0) 76-5721413
E-mail: RMADesk.STService@nl.bosch.com
Asia Region
Repair Center
Telephone: 65 63522776
Fax: 65 63521776
E-mail: rmahelpdesk@sg.bosch.com
Customer Service
Telephone: 86 (0) 756 7633117 or
86 (0) 756 7633121
Fax: 86 (0) 756 7631710
E-mail: customer.service@cn.bosch.com
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
12
en | Safety
High Performance LCD Monitors
Warranty and more information
For additional information and warranty queries, please contact
your Bosch Security Systems representative or visit our website
at www.boschsecurity.com.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
2
Unpacking | en
13
Unpacking
This equipment should be unpacked and handled with care. If
an item appears to have been damaged in shipment, notify the
shipper immediately.
Verify that all the parts listed in the Parts List below are
included. If any items are missing, notify your Bosch Security
Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to
transport the unit and must be used if returning the unit for
service. Save it for possible future use.
2.1
Parts List
The following table lists the parts included:
Quantity Part
1
UML-172-90, UML-192-90, or UML-202-90 Color LCD
1
2
Flat Panel Monitor
Installation manual
Power Cords, 3-wire with grounded plug 1.8 m (6 ft)
long:
one with a U.S plug type and one with a European
1
1
1
1
1
Bosch Security Systems, Inc.
Continental plug type
VGA to VGA (D-SUB) cable, 1.5 m (5 ft)
DVI-D to DVI-D cable, 1.5 m (5 ft)
Alarm relay cable with two flying leads
PC-style audio cable
Remote control with two (2) batteries
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
14
en | Unpacking
2.2
High Performance LCD Monitors
Exploded View
Figure 2.1
Front Panel UML-202
Figure 2.2
Front Panel UML-172 and UML-192
Number Button
Description
1
Input Button
Selects the signal to be displayed
2
Menu Button
Selects the on-screen display (OSD)
3

Adjusts the value when in the OSD
4

Adjusts the value when in the OSD or Scrolls down in the OSD
5

Decreases the value when in the OSD Scrolls left in the OSD
6

Increases the value when in the OSD Scrolls right in the OSD
7
IR Sensor
Remote control sensor
8
LED Indicator Power On (green)
9
Power Button Display Power (On/Off)
Scrolls up in the OSD
auto adjusts when in PC mode
Power Off, Standby (red)
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Unpacking | en
15
Figure 2.3 Side and Bottom Panels
Side Panel
Bottom Panel
Number Connector
Number Connector
1
Video 1 (AV1) IN
12
2
Video 1 (AV1) OUT
13
HDMI IN
DVI IN
3
Video 2 (AV2) IN
14
D-SUB IN
4
Video 2 (AV2) OUT
15
PC Stereo IN
5
S-Video (Y/C) IN
16
Audio OUT
6
S-Video (Y/C) OUT
17
Component Y, Pb, Pr and Sound L, R
7
Audio IN (AV1, S-Video)
18
DC 12 V IN
8
Audio OUT (AV1, S-Video)
19
Trigger Input
9
Audio IN (AV2)
10
Audio OUT (AV2)
11
12 V Adaptor
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
16
en | Unpacking
2.3
High Performance LCD Monitors
Remote Control
This section details the functions and the usage of the Bosch
remote control.
Button
Function
POWER
Turns the power ON and OFF.
SOURCE
Selects the PC or Video source.
Numbers
Numerals 0-9.
AUTO
Auto adjusts to the graphics adaptor.
MUTE
Mutes the sound.
MENU
Displays the OSD. Pressing the Menu button returns you to the Main
EXIT
Exits the OSD.
UP
Moves the cursor up in an OSD menu.
menu from anywhere in the OSD menus.
DOWN
Moves the cursor down in an OSD menu.
ENTER
Accepts your selection or displays the current mode when in the OSD
menu.

Moves the cursor left, decreases item values in an OSD menu, or
VOL
decreases sound.

Moves the cursor right, increases item values in an OSD menu, or
VOL
decreases sound.
INFO
Displays the information for the settings currently selected for CVBS or
STILL
Freezes the video by pressing the button once and releases the freeze
PIP
Activates/deactivates Picture-In-Picture mode.
P. INPUT
Selects the PC or Video source for the PIP. Continuously press this
P. POS
Moves the position of the sub picture for the PIP mode. Continuously
P. SIZE
Changes the size of the sub and main picture for the PIP mode.
SWAP
Alternates between the main and sub picture for the PIP mode.
PC Input.
by pushing it again.
button to change the selection.
press this button to change the selection.
Continuously press this button to change the selection.
Continuously press this button to change the selection.
ARC (Aspect
Selects the screen ratio when in Video mode. Continuously press this
Ratio Control)
button to change the selection.
APC (Auto
Selects the Picture mode. Continuously press this button to change
Picture Control) the selection.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Unpacking | en
17
ACC (Auto Color Selects the Color mode. Continuously press this button to change the
Control)
selection.
S. SET
Selects the Sound mode main input or sub input (only available when
PC
Selects the PC mode (HDMI, DVI, PC). Continuously press this button
PIP is enabled).
to change the selection.
AV
Selects the AV mode (AV1, AV2, S-Video). Continuously
COMP
Selects the COMPONENT mode.
press this button to change the selection.
2.4
Remote Control Battery Installation
1.
Turn the remote over (buttons facing down) and push
down on the cover and slide it off.
2.
Insert two (2) new AAA alkaline batteries, matching the
batteries to the (+) and (-) marks inside the battery case.
Figure 2.4
3.
Remote Control Battery Placement
Slide the battery cover back into place.
Note: Replace batteries when required or at least once a
year. Dispose of used batteries properly.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
18
en | Unpacking
F.01U.076.723 | 3.0 | 2009.03
High Performance LCD Monitors
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
3
Description | en
19
Description
The Bosch High Performance Family of LCD monitors display
PAL or NTSC standard color pictures in CCTV systems. Two (2)
looping Composite Video BNC connector inputs, two (2)
looping Audio input RCA, and two (2) looping Y/C (S-Video)
inputs using a 4-pin mini-DIN are included. In addition, each
model includes an Analog VGA input using 15-pin D-sub to
accommodate the increasing use of PCs and digital video
devices in security applications, an HDMI (High Definition
Multimedia Input), DVI, PC-RGB (VGA), RC Audio In and Out,
and Component Video (Y/Pb/Pr) connectors.
Monitor control functions are accessed via the front panel push
buttons and On-screen Display (OSD). See Section 2.2 Exploded
View, Page 14, for front panel descriptions.
3.1
Features
–
17-inch, 19-inch, and 20-inch models
–
90 to 256 VAC Power Supply
–
NTSC/PAL Auto-Detect
–
High-Resolution Display
–
1024 x 768 (UML-172-90)
–
1280 x 1024 (UML-192-90)
–
1600 x 1200 (UML-202-90)
–
VGA Input
–
Composite Video Input
–
Y/C Input (S-Video)
–
On-screen Display (OSD) with Multiple Languages
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
20
en | Description
3.2
Power
Model No.
Rated Voltage
UML-172-90 120/230 VAC
High Performance LCD Monitors
Voltage Range Power at Rated Voltage Sync Format
100 to 240 V < 40 W
NTSC/PAL
100 to 240 V
< 45 W
NTSC/PAL
90 to 256 V
70 W (max)
NTSC/PAL
50/60 Hz
UML-192-90 120/230 VAC
50/60 Hz
UML-202-90 120/230 VAC
50/60 Hz
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
4
Installing the Monitor | en
21
Installing the Monitor
This chapter outlines the procedures to install the UML-172-90,
UML-192-90, or the UML-202-90 Series. A qualified service
person should install the monitor and adhere to all local codes.
4.1
Ventilation
To prevent overheating, ensure that the ventilation openings on
the rear of the monitor are not covered.
4.2
Mounting the Monitor
The UML-172-90, UML-192-90, and the UML-202-90 are
designed for use on a desktop or mounted to a wall or rack.
4.2.1
Desktop Installation
The Bosch High Performance monitors are delivered with a 3pole US-style power cord and a 3-pole Euro-style power cord.
Use the US-style power cord where 120 VAC, 60 Hz power is
available; use the Euro-style power cord where 230 VAC, 50 Hz
power is available. The monitor automatically adjusts to either
power input voltage. The viewing angle of the LCD can be
adjusted to fit the most comfortable monitoring status.
Min Degree
25° 122 mm
i
Max Degree
50° 192 mm
NOTICE! For the best viewing quality and holding support, the
suggested bracket angle is 25° to 50°.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
22
en | Installing the Monitor
4.2.2
High Performance LCD Monitors
Wall Mount Installation
The square mounting holes (100 mm [3.9 in.] centers) are
compatible with the Bosch UMM-LW-20B fixed wall mount or
the UMM-LW-30B swivel/tilt mount.
Figure 4.1
4.3
Mounting the Device
Connecting the Composite Video Signal to
the Monitor
There are two (2) BNC connectors located on the rear side
panel of the monitor for composite video input and two (2) BNC
connectors for composite video outputs (see Figure 2.3).
Note: All video inputs are passive loop-through. The impedance
is automatically set to 75 ohm by the input of the signal on the
input connector, while operating in a single connection mode
(see Figure 4.7). If a cable is also connected to the output
connector, the video signal can be passed on to another
monitor connected to it via the passive loop-through function.
Up to three (3) monitors may be connected in this manner (see
Figure 4.8).
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Installing the Monitor | en
23
Note: To select between AV1 and AV2, press Input (see
Figure 2.1, Item 1 or Figure 2.2, Item 1) located on the front of
the monitor.
4.4
Connecting the Y/C (S-Video) Signal to the
Monitor
There is one (1) mini-DIN type connector for the S-Video (Y/C)
input (see Figure 4.2) on the rear side panel.
Note: Both Y and C inputs are terminated with 75 Ω resistors.
Figure 4.2
Number
1
2
3
4
4.5
Y/C Connection Pinout
Input
GND
GND
Y-signal IN or OUT
C-signal IN or OUT
Connecting Audio to the Monitor
There are two (2) sets of mono audio connectors for audio
input, located at the side panel.
–
All audio inputs are active loop-through.
–
Audio 1 is associated with Video 1 or Y/C; Audio 2 is
associated with Video 2.
Input
Video 1
Video 2
S-video
4.5.1
Audio 1
X
Audio 2
X
X
Connecting PC Audio
The rear bottom panel has PC stereo audio IN and audio OUT.
Connect with 1/8 in. mini phono plug jack to Audio IN.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
24
en | Installing the Monitor
4.6
High Performance LCD Monitors
Connecting the PC Signal to the Monitor
There are three ways to connect the PC signal to the monitor;
HDMI, DVI, and VGA.
4.6.1
HDMI
The monitor can be connected to the HDMI (High Definition
Multimedia Input) by connecting a HDMI cable (not supplied).
Figure 4.3
4.6.2
HDMI Input
DVI
The monitor can be connected by using the supplied DVI-D
cable and connecting it to the digital DVI-D signal.
Figure 4.4
4.6.3
DVI Input
VGA
The monitor can be connected by connecting the analog VGA
signal by using the provided VGA cable (D-SUB to D-SUB).
Figure 4.5
Pin
1
2
3
4
5
6
7
8
VGA Input
Description
Red Video
Green Video
Blue Video
Ground
Ground
Red Ground
Green Ground
Blue Ground
F.01U.076.723 | 3.0 | 2009.03
Pin
9
10
11
12
13
14
15
Installation Manual
Description
N/A
Signal Cable Detect
Ground
SDA (for DDC)
H-Sync or H+V Sync
V-Synch
SCL (for DDC)
Bosch Security Systems, Inc.
High Performance LCD Monitors
4.7
Installing the Monitor | en
25
Connecting an Alarm Trigger
The monitor contains an alarm Trigger Input, the right-most
input on the back panel, and an alarm relay cable. These
components allow you to connect an alarm relay from a device,
such as a camera or a door. Connect the two flying leads from
the alarm relay cable into the relay out ports of the device.
Then, route the other end of the cable to the Trigger Input
connector on the back panel of the monitor.
The following illustration depicts a typical alarm relay
configuration:
VIDEO
DC 12V
AC 24V
SVHS
SYNC
ALARM
Figure 4.6 Camera to Monitor Alarm Relay
Number
1
2
3
Description
Dinion Camera
Flying leads connected to relay outputs 3 and 4
UML Back Panel
In the above example, the flying leads of the alarm relay cable
are connected to relay output three and four of a Dinion
camera. The cable is routed to the back panel of the UML
monitor and the plug-end of the wire is connected to the
Trigger Input port. See Section 5.7.1 Configuring Alarm Relay
Inputs, Page 37, for configuring alarm acknowledgement.
Example: Typical Alarm Trigger Configuration
In this case, the Dinion camera is used to watch for motion.
When the camera detects motion it sends an alarm to the UML
monitor. The monitor, then, switches the input to display the
video from the Dinion camera and sounds a buzzer.
1.
Route the coax cable from the Dinion Video output to the
AV1 input of the UML monitor.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
26
en | Installing the Monitor
2.
3.
High Performance LCD Monitors
Configure the following settings for the Dinion camera:
–
VMD: OSD
–
Area: 1
–
Active: On
Connect one flying lead to relay output three, on the back
of the Dinion camera, and connect the other to relay
output four.
4.
Connect the other end of the Trigger Relay cable to the
Trigger Input connector on the back of the monitor.
5.
Plug the monitor into a power socket; then press the
Power button.
6.
On the monitor, access the Trigger menu:
a.
b.
Press the Menu button.
Press the Down Arrow button to access the Setup
menu.
c.
Press the Right Arrow button to enter the Setup
d.
Press the Down Arrow button until Trigger is
menu.
highlighted; then press the Right Arrow button.
7.
Make the necessary changes to the Trigger menu so that
the settings match the following:
Trigger
Trigger Enable
Trigger Type
Trigger Input
Buzzer
Trigger Time
Trigger Option
Display Type
:Move
8.
On
External
AV1
On
10
N/O
M/C
:Input
:Menu
Press the Menu button three (3) times to exit the menu
and to return to the video display.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
4.8
Installing the Monitor | en
27
Single / Multiple Monitor Configuration
Figure 4.7
Number
1
2
3
4
Single Monitor Configuration
Description
Video Camera
VIDEO 2 (AV2) IN
VIDEO 2 (AV2) OUT
VCR
Figure 4.8 Multiple Monitor Configuration
Number
1
2
3
Bosch Security Systems, Inc.
Description
Video Camera
VIDEO 2 (AV2) IN
VIDEO 2 (AV2) OUT
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
28
en | Installing the Monitor
F.01U.076.723 | 3.0 | 2009.03
High Performance LCD Monitors
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Navigating the Monitor | en
5
Navigating the Monitor
5.1
Navigating the Front Panel
29
Use the front panel to make any necessary OSD adjustments to
the UML-172-90, UML-192-90, or to the UML-202-90. See the
figure below for an explanation of the front panel.
Figure 5.1 Front Panel Buttons
Number Button
1
Description
Input Button
Selects the signal to be displayed
2
Menu Button
Selects the on-screen display (OSD)
3

4

Scrolls up in the OSD
Performs an Autoset when
Scrolls down in the OSD
connected to the VGA input, which
automatically adjusts the display to
match the graphics adapter.
5

Decreases the value
Scrolls left in the OSD
6

Increases the value
Scrolls right in the OSD
7
IR Sensor
Remote control sensor
8
LED Indicator
Power On (green)
9
Power Button Display Power (On/Off)
Power Off, Standby (red)
5.2
Navigating the Monitor On-screen Display
(OSD)
The UML172-90, UML-192-90, and the UML-202-90 have two (2)
modes: Video and PC. The LCD is programmed through the onscreen display (OSD) menus and submenus where an operator
can select operating parameters. To access the OSD menus,
press the Menu button on the front panel or on the remote
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
30
en | Navigating the Monitor
High Performance LCD Monitors
control. Use the front panel of the monitor or respective remote
control to make any necessary adjustments to the OSD.
i
NOTICE! When you are navigating through the OSD menus, use
the Input button to select a menu and use the Menu button to
exit a menu.
To navigate the set up menus, follow the steps below:
1.
2.
Connect the CVBS or VGA cable.
If required, press the Input button until a signal is
displayed. NOTE: Menus are not available without a signal
applied.
3.
Press the Power button to turn on the unit (see Figure 2.1
or Figure 2.2).
4.
Press the Menu button to activate the main menu
selections (see Figure 2.1 or Figure 2.2).
5.
Press the  and  buttons to select a menu.
6.
Press the Input button to enter the selected menu.
7.
Press the  and  buttons to select a sub-menu item.
8.
Press the  and  buttons to toggle the OSD values.
9.
Press the Menu button to exit the selected menu and to
return to the menu bar or to confirm a selection.
10. Press the Menu button again to exit the OSD menu bar.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
5.3
Navigating the Monitor | en
31
On-screen Display Menus
There are four (4) on-screen menus that allow you to customize
your settings. Press the Menu button to access the OSD menu.
Icon
Menu
Custom
Function
Adjusts the Brightness, Contrast, Color, Tint, and the
Sharpness level for video performance of the OSD. (The menu
options differ between the Video and PC modes.)
Picture / Sound Adjusts the Picture Mode, Color Tone, Mute, Volume, Size,
and the PC settings. (The menu options differ between the
Video and PC modes.)
PIP
Adjusts the Input Source, Size, Position, Swap, and the
Sound Select settings.
Set Up
Enables user to Reset the factory default settings and to
adjust the Language, OSD Tone, Blue Screen, Key Lock,
Trigger, and Auto Switching settings.
5.4
Custom Menu
To access the Custom menu, press the Menu button on the
front panel of the monitor. Next, press the right arrow and then
press the up and down arrows to select a submenu. Press the
left and right arrow buttons to increase or decrease the values.
When finished, press the Menu button to save any changes,
then press the Menu button again to exit the OSD.
Custom
:Move
Brightness
Contrast
Color
Tint
Sharpness
Phase
50
50
50
50
20
3
:Input
:Menu
Table 5.1 Custom Menu (Video Mode)
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
32
en | Navigating the Monitor
High Performance LCD Monitors
Custom
Brightness
Contrast
:Move
50
50
:Input
:Menu
Table 5.2 Custom Menu (PC Mode)
Submenu
Definition
Brightness
Adjusts the brightness level for video performance (range 0-
Contrast
Adjusts the contrast level for video performance (range 0-100).
100).
Color
Adjusts the overall intensity of the screen (range 0-100).
Tint
Adjusts the tint of the picture (range 0-100). NTSC only.
Sharpness
Adjusts the sharpness level for video performance (range 0100).
Phase (Component only)
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
5.5
Navigating the Monitor | en
33
Picture / Sound Menu
To access the Picture / Sound menu, press the Menu button on
the front panel of the monitor, then press the left and right
arrows to select the Picture / Sound icon. Press the up and
down arrows to select the Picture / Sound submenu.
Picture/Sound
Picture Mode
Color Tone
Mute
Volume
Size
DNR
3D Comb
:Move
Custom
Normal
Off
20
4:3
On
On
:Input
:Menu
Table 5.3 Picture / Sound Menu (Video Mode)
Picture/Sound
Picture Mode
Color Tone
Mute
Volume
Size
PC
:Move
Custom
Normal
Off
20
4:3
:Input
:Menu
Table 5.4 Picture / Sound Menu (PC Mode)
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
34
en | Navigating the Monitor
High Performance LCD Monitors
Submenu
Definition
Picture Mode
Selects the automatic picture control mode. Choices are:
(Video Mode)
Custom: User selected values of the Custom menu are applied.
Dynamic: Automatically adjusts the Brightness, Contrast, and
Sharpness, maximizing the video quality in the picture.
Standard: Applies factory default values.
Picture Mode (PC
Selects the automatic picture control mode. Choices are:
Mode)
Custom: User selected values of the Custom menu are applied.
High: Uses the following values: Brightness = 70, Contrast = 80
Middle: Uses the following values: Brightness = 60, Contrast = 70.
Low: Uses the following values: Brightness = 50, Contrast = 60.
Color Tone
Selects the color temperature. Choices are: Cool 9300K, Normal
6500K, Warm 5000K.
Mute
Enables/disables audio. Choices are: On and Off.
Volume
Controls built-in speaker output volume (range 0-100).
Size (Video Mode)
Selects the Aspect Ratio Control mode. Choices are: 4:3,
Panorama, Zoom1, Zoom2, Wide.
DNR (Video Mode)
Turns Noise Reduction On or Off. Turning this feature OFF
reduces the video quality slightly, but improves the monitors
response time to MOTION.
PC (PC Mode)
Selects between Auto or manual adjustment of the desktop
screen. Auto Adjust: Auto synchronizes screen to graphics
adaptor.
Manual choices are: Phase (range 0-100), H-Position (range 0100), V-Position (range 0-100), Frequency (range 0-100).
3D Comb
Activates the 3D comb filter.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
5.6
Navigating the Monitor | en
35
PIP Menu
To access the PIP menu, press the Menu button on the front
panel of the monitor, then press the left and right arrows to
select the PIP icon. Press the up and down arrows to select the
PIP submenu.
PIP
PIP
On
Input Source AV1
Size
Position
Swap
Sound Select Main
:Move
:Input
:Menu
Table 5.5 PIP menu
Submenu
Definition
PIP
Activates the PIP feature.
Input Source
Select the video input source for the PIP area. The selections depend on
the main video input source. Analog video sources (AV1, AV2, S-Video)
can display only digital video (Component, HDMI, DVI, PC) inputs in the
PIP area; digital video sources can only display analog video inputs in the
PIP area.
AV1, AV2, S-Video: Component, HDMI, DVI, PC
Component, HDMI, DVI, PC: AV1, AV2, S-Video
Size
Enables 3 screen sizes: full screen side by side, 4:3 side by side, and 4:3
Position
Enables 4 positions: bottom right, top right, bottom left, top left.
Swap
Alternates between the main and sub picture for the PIP mode.
corner (177 mm [3.03 in.] diagonal).
Continuously press to change selection.
Sound Select Select the sound source from either the Main or the PIP input source
(only available when PIP is enabled).
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
36
en | Navigating the Monitor
5.7
High Performance LCD Monitors
Setup Menu
To access the Setup menu, press the Menu button on the front
panel of the monitor, then press the left and right arrows to
select the Setup icon. Press the up and down arrows to select
the Setup submenu.
Setup
Reset
Language
OSD Tone
Blue Screen
Key Lock
Trigger
Auto Switching
Firmware Version
:Move
:Input
English
Blue
Off
Off
X.XX
:Menu
Table 5.6 Setup Menu
Submenu
Definition
Reset
Restores default settings.
Language
Adjusts the language of the OSD. Choices are: English, French,
German, Italian, Dutch, Spanish, and Portuguese.
OSD Tones
Selects the type of background for the OSD menu. Choices are:
Transparency and Blue.
Blue Screen
Enables or disables video loss indication. Choices are:
On: displays a blue background when video loss is detected.
Off: displays a black backgound when video loss is detected.
Key Lock
Enables or disables the Key Lock function.
Trigger
Opens the Trigger menu allowing you to configure the monitor’s
repsonse to incoming alarms. See Section 5.7.1 Configuring Alarm
Relay Inputs, Page 37.
Auto Switching
Opens the Auto Switching menu allowing you to configure the way
the monitor cycles through video inputs. See
Section 5.7.2 Configuring Auto Switching, Page 39.
Firmware Version Displays the release level of the monitor firmware.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Navigating the Monitor | en
37
NOTICE! When key lock is enabled through the front panel, use
either the remote control or the front panel buttons to disable
i
the key lock command. To disable the key lock feature using the
front panel buttons, press and hold both the Input and the
Menu buttons until the monitor displays the Key Unlocked
message.
5.7.1
Configuring Alarm Relay Inputs
The monitor allows you to connect an alarm relay cable from a
device (camera or door) to the monitor, and then to configure
the monitor’s response to an incoming alarm (see
Section 4.7 Connecting an Alarm Trigger, Page 25).
Trigger
Trigger Enable
Trigger Type
Trigger Input
Buzzer
Trigger Time
Trigger Option
Display Type
:Move
Off
External
AV1
On
20
N/O
PIP & FULL
:Input
:Menu
Table 5.7 Trigger Menu
Option
Definition
Selections
Trigger Enable Activates the trigger feature.
ON or OFF
Trigger Type
External
Specifies the source of the alarm. This option is
always set to External.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
38
en | Navigating the Monitor
High Performance LCD Monitors
Option
Definition
Selections
Trigger Input
Select the video input source that the monitor
AV1
displays when an alarm is activated. When the
AV2
monitor receives an alarm input, it switches to the
S-Video
speficied input source.
Component
HDMI
DVI
PC
Buzzer
Activates an audible signal when the monitor
ON or OFF
receives an alarm input and switches to the Trigger
Input video source.
Note: If the Input video source is the same as the
Trigger Input, the monitor does not sound the
buzzer.
Trigger Time
Select the amount of time, in seconds, that the
0–100 seconds
monitor displays the Trigger Input video source.
Trigger Option Select the type of physical trigger input. Consult the N/C
manual for the alarm source to determine your
(normally closed)
selection.
N/O
(normally open)
High (2–5 V)
Low (< .6 V)
Display Type
Select the mode in which the monitor displays the
PIP & FULL
Trigger Input. The monitor takes one of the following FULL
actions:
–
Displays the Trigger Input in the Picture-inPicture position (PIP & FULL) of the current
video input source.
Note: The main video source must support the
Trigger Input source as a PIP option. See
Section 5.6 PIP Menu, Page 35.
–
Switches the display to show the Trigger Input
in the full screen (FULL).
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
5.7.2
Navigating the Monitor | en
39
Configuring Auto Switching
The Auto Switching feature allows the monitor to cycle the
display of selected video inputs.
Auto Switching
Auto Switching
Input
Time
:Move
Off
10
:Input
:Menu
Table 5.8 Auto Switching Menu
Option
Definition
Selections
Auto Swtiching Activates the Auto Switching feature.
ON or OFF
Input
Opens another menu in which you select the input
Time
Select the amount of time, in seconds, that the monitor 0–100 seconds
sources to include in the Auto Switching cycle.
displays each selected input source.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
40
en | Navigating the Monitor
High Performance LCD Monitors
Selecting Input Sources for Auto Switching
Use this menu to add or remove an input source from the Auto
Switching cycle.
Auto Switching
AV1
AV2
S-Video
Component
HDMI
DVI
PC
:Move
On
On
On
On
On
On
On
:Input
:Menu
Table 5.9 Auto Switching Menu – Input Source Selection
1.
Use the Up and Down arrow buttons to select an input
source.
2.
Press the Right Arrow to change the status of the input
3.
Use the Up and Down arrow buttons to change the status
source.
of the input source:
–
Select On to include the input source in the cycle.
–
Select OFF to remove the input source from the cycle.
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
6
Power Management | en
41
Power Management
These monitors feature a power management system to “power
down” upon receipt of the display power management signaling
(DPMS) from a DPMS video card.
The DPMS-compliant video card performs this signaling system
by not sending a horizontal, vertical, or a sync signal.
The monitor enters an appropriate mode through identifying
each of the three (3) modes of the signaling system.
6.1
Power Consumption
Mode
ON
STANDBY
SUSPEND
ACTIVE OFF
6.2
Power Consumption
70 W
10 W
10 W
10 W
LED Indicator
The power management feature of the monitor is comprised of
these stages:
Mode
ON
STANDBY
SUSPEND
ACTIVE OFF
UNSUPPORTED
MODE
POWER OFF
LED
Monitor Operation
Color
Green Normal operation
Flashes Screen blanks after idle time and some electronic
Red
circuits or all circuitry in the monitor shuts down.
Green
Normal operation but the screen displays an error
Red
message.
Not operational.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
42
en | Power Management
F.01U.076.723 | 3.0 | 2009.03
High Performance LCD Monitors
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
7
Maintenance | en
43
Maintenance
To clean the LCD panel, wipe off water droplets or oil
immediately with absorbent cotton or a soft lint-free cloth.
Staining and discoloration may occur if left on the panel for
long periods.
If the surface (polarizer) of the LCD panel is dirty or stained,
use absorbent cotton or a soft lint-free cloth to remove the
residue as follows:
1.
2.
Turn off the computer or display.
Do not spray any liquid directly on the screen. Dampen a
clean, soft, lint-free cloth with water only (using a paper
towel or dirty cloth can scratch the screen).
3.
Gently wipe the screen starting from the top of the screen
to bottom wiping in a downward motion. Be careful not to
press too hard to avoid damaging the screen.
4.
To avoid streaking, wipe the screen again with another
clean, dry, lint-free cloth.
i
NOTICE! If water does not work, use a mild cleaner labeled for
use with LCD panels, available at office supply stores.
Do not use any of the following as a cleaning agent:
–
Ketone type materials
–
Ethyl alcohol
–
Ethyl acid
–
Toluene
–
Methyl chloride
–
Ammonia
Use of these materials may permanently damage the polarizer
due to a chemical reaction.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
44
en | Maintenance
F.01U.076.723 | 3.0 | 2009.03
High Performance LCD Monitors
Installation Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
8
TroubleShooting Guide | en
45
TroubleShooting Guide
Problem
Solution
No image is
–
displayed on
Check that the power cord of the monitor is securely
connected into the wall outlet or grounded extension
screen
cable or strip.
–
Power switch should be in the ON position and the
–
Check that the Brightness and/or Contrast
LED lit.
adjustments of the display have not been turned
down to minimum levels.
“Going to
–
Sleep” message
is displayed
The signal cable should be completely connected to
the video card/computer.
–
The video card should be completely seated in its slot
and the computer switched ON.
Display image is –
Push the down key to activate the Autoset function.
not centered, is
-or-
too small, or too –
Adjust the Clock and Phase in the PC OSD submenu.
large in the PC
mode
Monitor does
Compare the Trigger Option setting on the Trigger menu
not switch upon with the physical alarm output setting for alarm device.
trigger input
Monitor does
If the video input and the Trigger Input are from the same
not sound the
source:
buzzer
–
Set the Trigger Time to zero (0).
If the video input and the Trigger Input are from different
sources, check the following settings on the Picture/
Sound menu:
–
Ensure that the Mute option is set to OFF.
–
Ensure that the Volume is set to an audible level.
Bosch Security Systems, Inc.
Installation Manual
F.01U.076.723 | 3.0 | 2009.03
46
en | TroubleShooting Guide
Problem
Solution
Vertical or
–
High Performance LCD Monitors
Push the down key to activate the Autoset function
horizontal noise
(for VGA inputs only).
is present in the
-or-
picture
–
Incorrect colors –
Adjust the Clock and Phase in the PC OSD submenu.
Press the Menu button on the front panel of the
monitor, then press the down arrow to select the
Color Tone menu. Press the down arrow on the front
panel and select Cool, Warm, or Normal.
- or -
–
Press the Menu button on the front panel of the
monitor, then press the right arrow to select the
Setup menu. Press the down arrow on the front panel
and select Recall to reset to the default settings.
The error
PC is operating with either a resolution or timing mode
message “Out of that is not supported by the monitor. Change the PC
Range” is
timing mode to one of the valid combinations below:
displayed
640 x 480; 60/72/75 Hz
800 x 600; 60/72/75 Hz
1024 x 768; 60/70/75 Hz
1280 x 1024; 60 Hz
1600 x 1200; 60 Hz
F.01U.076.723 | 3.0 | 2009.03
Installation Manual
Bosch Security Systems, Inc.
Americas
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, Pennsylvania 17601
USA
Telephone +1 888-289-0096
Fax
+1 585-223-9180
Email:
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven,
The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.c
om
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
apr.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems, Inc. 2009; F.01U.076.723 | 3.0 | 2009.03; Data subject to change without
notice.
Download PDF

advertising